Low-cost particulate matter (PM) sensors offer an excellent opportunity to improve our knowledge about this type of pollution. Their size and their cost, which support multi-node network deployment, along with their temporal resolution, enable them to report fine spatio-temporal resolution for a given area. These sensors have known issues across performance metrics. Generally, the literature focuses on the PM mass concentration reported by these sensors but some models of sensors also report particle number concentrations (PNC) segregated into different PM size bins. In this study, 8 units of each Alphasense OPC-R1, Plantower PMS5003 and Sensirion SPS30 have been exposed, under controlled conditions, to short-lived peaks of PM generated using two different combustion sources of PM, exposing the sensors to different particle size distributions to quantify and better understand the low cost sensors performance across a range of relevant environmental ranges. The PNC reported by the sensors were analysed. This study showed that there is added value in directly using the PNC reported by the sensors instead of the mass concentrations, which could aid the efforts to calibrate these sensors to a known accuracy. It demonstrated that all sensors tested here could track the fine temporal variation of PNC, that the Alphasense OPC-R1 could closely follow the variations of size distribution between the two sources of PM, and it showed that particle size distribution and composition are more impactful on the sensors measurement than relative humidity.

Air pollution is a leading cause of death worldwide, and has a profound impact on the planet's climate and ecosystems. A substantial portion of air pollution is attributable to Ocean Going Vessels (OGVs). In light of this, international regulations have been put in place to mitigate air pollutant emissions from OGVs. While studies have indicated that these regulations can create significant health, environmental, and economic benefits, there remains a research gap regarding their specific impact on enhancing air quality. The aim of this study is to investigate how the implemented regulations have affected air quality in the Southern North Sea. The study found that the international regulations on ship emissions have successfully led to a decline in SO2 emissions from OGVs in the Southern North Sea, which resulted in a reduction of ambient SO2 concentrations inland, leading to positive effects on public health and the environment. However, it was projected that their proportion is tend to increase in the following years. Moreover, the study revealed that Exhaust Gas Cleaning Systems (EGCS) present significant concerns. They were significantly more frequently found to be non-compliant, and more alarmingly, they emit notably higher average levels of SO2. It also turned out that international regulations in the southern North Sea have less effect on the reduction of NOx emissions from OGVs than expected. The NOx emissions from OGVs will even account for an alarming 40% of the total domestic NOx emissions for the Belgian Region by 2030.

A combination of compost and biochar has been proven to be a promising strategy to immobilize metal(loid)s and improve soil properties. To the best of our knowledge, no study has been conducted to investigate the effect of biochar and compost combination administered at different rates on mining technosol. Thus, we investigated the effect of different rates of compost (20%, 40%, 60% w/w) in combination with biochar (0%, 2%, 6% w/w) on soil physiochemical properties and the mobility of arsenic (As) and lead (Pb), the ability of Arabidopsis thaliana (ecotype Columbia-0) to grow and accumulate metal(loid)s. All modalities improved pH and electrical conductivity, stabilized Pb and mobilized As, but only the mixture of 20% compost and 6% biochar improved plant growth. Plants in all modalities showed a significant reduction in root and shoot Pb concentrations compared to the non-amended technosol. Whereas, As shoot concentration was significantly lower for plants in all modalities (except with 20% compost only) compared to non-amended technosol. For root As, plants in all modalities showed no significant reduction except for the mixture of 20% compost and biochar. Overall, the mixture of 20% compost with 6% biochar represents the optimum combination for improving plant growth and As uptake.

Spatial variation of indoor and outdoor PM2.5 within three states for a 5-year period is studied using regulatory and low-cost PurpleAir monitors. Most of these data were collected in an earlier study1 investigating the relative contribution of indoor-generated and outdoor-infiltrated particles to indoor exposures. About 260 regulatory monitors and ~10,000 outdoor and ~4,000 indoor PurpleAir monitors are included. Daily mean PM2.5 concentrations, correlations, and coefficients of divergence (COD) are calculated for pairs of monitors at distances ranging from 0 (collocated) to 200 km. We use a transparent and reproducible open algorithm that avoids use of the proprietary algorithms provided by the manufacturer of the sensors in PurpleAir PA-I and PA-II monitors. The algorithm is available on the PurpleAir API website under the name “PM2.5_alt”. This algorithm is validated using several hundred pairs of regulatory and PurpleAir monitors separated by up to 0.5 km. The PM2.5 spatial variation outdoors is homogeneous with high correlations to at least 10 km, as shown by the COD index under 0.2. There is also a steady improvement in outdoor PM2.5 concentrations with increasing distance from the regulatory monitors. The spatial variation of indoor PM2.5 indoors is not homogeneous even at distances <100 m. We document substantial differences between Federal Reference Methods (FRM) and Federal Equivalent Methods (FEM).

Heavy metal contamination is listed among the most alarming threats to the environment and human health. The detrimental effects of heavy metals in the natural environment span from a reduction of biodiversity to toxic effects on marine life - through microplastic born heavy metals -, to impairment of microbial activity in the soil, and to detrimental effects on animal reproduction. A host of different chemical and biological technologies have been proposed to alleviate environmental contamination by heavy metals. Relatively less attention has been paid to the microbial precipitation of heavy metals, as a side mechanism of the most general process of microbially induced calcite precipitation (MICP). This process is currently receiving a great deal of interest from both a theoretical and practical standpoint, because of its possible practical applications in concrete healing and soil consolidation, and its importance in the more general framework of microbial induced mineral precipitation. In this study, we analyse the ability of the marine bacteria Vibrio harveyi in co-precipitating CaCO3 minerals, together with Cd, Cr, Pb, and Zn added in form of nitrates, from solutions containing CaCl2. The precipitated carbonatic minerals were a function of the different heavy metals present in the solution. The process of co-precipitation appears to be rather effective and fast, as the concentrations of the 4 heavy metals were reduced in 2 days by 97.2%, on average, in the solutions.

Integrated assessment modelling (IAM) has been successfully used in the development of international agreements to reduce transboundary pollution in Europe, based on the GAINS model of IIASA. At a national level in the UK a similar approach has been taken with the UK Integrated Assessment Model, UKIAM, superimposing pollution abatement measures and behavioural change on energy projections designed to meet targets set for reduction of greenhouse gas emissions, and allowing for natural and imported contributions from other countries and shipping. This paper describes how UKIAM has been used in development of proposed targets for reduction of fine particulate PM2.5 in the Environment Act, exploring scenarios encompassing different levels of ambition up to 2050 with associated health and other environmental benefits. There are two PM2.5 targets, an annual mean concentration target setting a maximum concentration to be reached by a future year, and a population exposure reduction target with benefits for health across the whole population. The work goes further, to also demonstrate links to social deprivation. There is a strong connection between climate measures aimed at reducing net GHG emissions to zero by 2050 and future air quality, which may be positive or negative, as illustrated by sectoral studies for road transport where electrification of the fleet needs to match the evolution of energy production, and for domestic heating where use of wood for heating is an air quality issue. UKIAM has been validated against air pollution measurements and other modelling, but there are many uncertainties including future energy projections. New work is beginning to link UKIAM directly with the TIMES model addressing future energy projections, to explore different uptake scenarios for hydrogen production and use with respect to air quality.

With a worldwide growing concern for greenhouse gas (GHG) emissions and their impact on human health and the environment, transportation has become a central theme in mitigation, responsible for 14% of human GHG emissions. To build endurance to climate change, transportation services must adapt to the current scenario and act quickly to avert future changes. Deeply rooted changes in socio-technical systems will be necessary to achieve significant CO2 reduction and secure the well-being of future generations. This study's objective is to comprehensively review the current state of carbon mitigation in the transportation sector. This is done through a systematic literature review engrained in the socio-technical transition theory and the structural theory of contingency. Twenty-six review papers covering 2,983 original articles are selected for full-text examination concerning carbon emissions in transportation. Enablers, barriers, benefits, disadvantages and metrics in carbon emissions reduction are identified, and a comprehensive framework is built. Results provide a view of the current sustainability scenario in transportation and allow a better understanding of the factors influencing carbon emission initiatives in transportation and its outcomes.

Plastic contamination is a burning issue costing the global cotton and textile industries billions of dollars annually. Any time plastics from different sources end up in a cotton lint bale, the value to the textile mills plummets significantly. Various industry players have therefore made a concerted effort to find lasting solutions to the menace posed by plastic to cotton profitability and sustainability. Nevertheless, until now, there have been no up-to-date comprehensive documents detailing the numerous and ever-growing efforts committed to solving this challenge. Therefore, this article provides a detailed yet compact review of this highly dynamic subject matter. First, it puts into perspective plastic contamination in the cotton and textile industries. Then, the cotton value chain is subdivided into phases from pre-cultivation to textile mills. The root causes of plastic contamination are discussed in each stage, followed by discussions of some already developed and emerging solutions in response to the challenge by the affected industries and researchers. Concluding from the author’s perspective, the paper makes projections for the future directions of plastic mitigation efforts within the cotton and textile industries. This article also infers from the reviewed literature that research on finding alternative materials to plastic as module wrap, the development of new, effective, and all-condition plastic sensing techniques for ginning and spinning equipment, and standardized protocols for UAV in-field surveys of plastic trash are some of the areas that will be beneficial to finding a permanent solution to the challenge.

The increasing regulatory pressure to monitor and reduce GHG emissions and air pollutants requires cost-effective methods for their surveillance. The most common technique used for scientific investigations on gas concentration monitoring in barns are accurate but expensive and with a complex maintenance. This research study analysed the potential use of a low-cost portable measurement devices for the measurement of ammonia (NH3) and carbon dioxide (CO2) concentrations in an open dairy barn. A comparison between gas concentrations acquired at different heights from the floor by using portable devices and those acquired by a photoacoustic infrared multigas spectroscope (i.e., reference measurement) in the same sampling locations was carried out to determine the precision of the low-cost portable devices. The performance of low-cost portable devices was statistically analysed by the application of the one-way analysis of variance, correlation analysis and regression analysis. The results showed a significant difference between gas concentration values at various heights from the floor for both NH3 and CO2. The correlations between concentrations acquired by the low-cost portable device and the INNOVA were statistically significant (r=0.83; P&lt;0.001) for gas concentrations monitored at 0.4 m from the floor. Compared with the reference measurement device, the low-cost devices were effective in the monitoring of NH3 concentrations at 0.40 m from the floor though it underestimated them in the barn at increasing of the height from the floor, whereas the device was not adequate for CO2 concentrations. In detail, the relative measurement error of the low-cost devices compared to INNOVA was reduced close to the floor during NH3 concentration measurements. Within these limitations, this device could be useful for monitoring NH3 concentration in the barn and to assess variation in NH3 concentrations mainly related to the animal occupied zone. Further efforts are needed in this field of research to identify low-cost device that could simplify emission estimation from open dairy barns.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

A quality marine ecosystem if it is free from GTP contaminants. Accuracy and caution are needed in the exploitation of marine resources as marine tourism destinations so that in the future, there will be no ecological hazards that cause chain effects, not only on aquatic ecosystems but also on humans. This article identifies exposure to GTP (MP, PAH, PR, HM, MW) in marine ecosystems in the MTA area and BCI waters. The combination of qualitative and quantitative analysis methods uses a combination of analytical instruments and mathematical formulas. The search results show the average total abundance of MP in seawater and fish samples (5.47 units/m3) and (7.03 units/m3), respectively, while in sediment and sponge samples (8.18 units/m3) and (8.32 units/m3). Based on the analysis of the polymer structure, it was identified that the dominant light group MP (PE, PP and PS), followed by PA and PC. Several PAH pollutants were identified in the samples, especially NL types found in all samples, followed by PN and AZ. BCI sea waters are suspected to be exposed to MW and PR. Pollutants of Pb+2 and Cu+2 around BCI were successfully calculated with average concentrations in seawater 0.164 mg/L and 0.294 mg/L, respectively, while in fish, 1.8110 µg/g and 2,452 µg/g, respectively. Based on these findings, the BCI area is not recommended as a marine tourism destination.

The Particulate Matter (PM), particles of variable but small diameter could penetrate the respiratory system via inhalation, causing respiratory and/or cardiovascular diseases. This study aims to evaluate the association of environmental particulate matter (PM2.5) and black carbon (BC) with respiratory health and physical activity in users traveling by transportation modes over four roads in Bogotá. This was a mixed-method study, in 300 healthy participants, based on a convergent parallel design. Including a descriptive qualitative component focused on asserting the individual perception of air pollution by semi-structured interviews and a cross-sectional study measuring the individual exposure to PM2.5 and BC to evaluate the pulmonary function by spirometry. The analysis included concurrent triangulation and a Poisson regression. This study provides integration of air pollution exposure variables and respiratory health effects in different transport microenvironments. To our knowledge, this is the first mixed-methods study focused on PM2.5, BC, and respiratory health effects in a city above 2.000 meters above sea level.

The article analyzes two existing social, technical and economic problems which the world community shall focus on and pay special attention to.

Background: Particulate matter and urban air pollution affect the human body and can lead to death. Epidemiological studies should consider the exposure to pollutants and the diverse responses of individuals depending on their sensitivity to the pollutants. Methods: In this study, air pollution measurements were obtained hourly at measuring stations operated by the national and local governments to increase the reliability of the measured values. A β-ray absorption method was used to analyze the measurements of fine dust and determine the particulate matter content. Results: The air pollution data were log-converted to enable the comparison of data from different time periods. The comparison was made, focusing on the period of Seoul's fine dust policy. As a result, the cancer incidence rate also decreased after the policy. The data on individual characteristics were obtained from a survey of Seoul citizens conducted from 2015 to 2016 and using indicators such as the quality of life and social trust of Seoul citizens. Concludions: The survey on the living environment and residence indicated that 80% of the heads of households were men. Women had a greater dissatisfaction than men with the residential, economic, and social environments. The survey questions on well-being were related to the internal and external environment such as air pollution, noise, and fine dust.

Clairton, Pennsylvania, is home to the largest coke works facility in the United States (US). On 24 December 2018, a large fire occurred at this facility and damaged pollution control equipment. Although repairs were not completed for several months, production continued at pre-fire capacity and daily emissions increased by 24 to 35 times, with multiple exceedances of monitored levels of outdoor air pollution (OAP). The aim of this study was to objectively evaluate the impact of this industrial incident and resultant OAP exceedances on asthma morbidity. We assessed pre-fire and post-fire rate ratios (RR) of outpatient and emergency department (ED) visits for asthma exacerbations among nearby adult residents. Pre-fire versus post-fire RRs increased for both visit types: RR = 1.82 (95% CI: 1.30, 2.53; p < 0.001) and 1.84 (95% CI: 1.05, 3.22; p = 0.032) for outpatient and ED visits, respectively. Additionally, total visit rates increased on days with OAP exceedances: RR = 2.47 (95% CI: 1.52, 4.01; p < 0.0001), 1.58 (95% CI: 1.00, 2.48; p = 0.048) and 1.79 (95% CI: 1.27, 2.54; p = 0.001) for PM_2.5, SO₂, and H₂S exceedance days, respectively. These results show a near doubling of acute visits for asthma exacerbations in nearby adult residents during this industrial incident and underscore the need for prompt remediation and public notification of OAP exceedances to prevent adverse health impacts.

Understanding the relationships between land cover/urban structure patterns and air pollutants is key to sustainable urban planning and development. In this study, we employ a mobile monitoring method to collect PM_2.5 and BC data in the city of Philadelphia, PA during the summer of 2019 and apply the Structure of Urban Landscapes (STURLA) methodology to examine relationships between urban structure and atmospheric pollution. We find that, while PM_2.5 and BC vary by STURLA class, many of the differences in pollutant concentrations between classes are not significant. However, we also find that the proportions in which STURLA components are present throughout the urban landscape can be used to predict urban air pollution. Among frequently sampled STURLA classes, gpl hosted the highest PM_2.5 concentrations on average (16.60 _± 4.29 µg/m³), while tgbwp hosted the highest BC concentrations (2.31 _± 1.94 µg/m³). Furthermore, STURLA combined with machine learning modeling was able to correlate PM_2.5 (R²= 0.68, RMSE 2.82 µg/m³) and BC (R² = 0.64, RMSE 0.75 µg/m³) concentrations with the urban landscape and spatially interpolate concentrations where sampling did not take place. These results demonstrate the efficacy of the STURLA methodology in modeling relationships between air pollution and land cover/urban structure patterns.

The frequent incidents of oil spills and other forms of pollution arising from crude oil exploration and exploitation (OEE) in the Niger Delta have caused several investigations on Polycyclic Aromatic Hydrocarbons (PAHs) pollution. This study aimed at developing a comprehensive report on PAH pollution and its human health risks recorded in the Niger Delta. Studies were extracted from Google Scholar, PubMed, and ResearchGate using a defined selection criterion. The quality of each study was assessed using the Newcastle – Ottawa Scale. Thirty-eight studies were selected with the majority reporting on PAH pollution in aquatic environments. Across all the selected studies, the total number of PAHs recorded ranged from 7 to 28 PAH congeners. Also, PAH potential sources reported in the studies were of pyrogenic and petrogenic sources. PAH concentrations recorded in water, sediment, aquatic organisms (fish and shrimp), soil, dust, and crop samples ranged from below detection limit (BDL) to 450 ± 117.9 mg/L, BDL to 1821.5 mg/kg, 0.005 to 1.098 mg/kg, ND to 4154 ± 3461 mg/kg, 165.1 to 1012 mg/kg, and 0.020 to 3.37 mg/kg, respectively. Majority of the selected studies reported PAH levels which were higher than the permissible limits. Incremental Lifetime Cancer Risk (ILCR) assessment of PAHs in samples ranged from low to high via ingestion and dermal routes of exposure to humans. It is recommended that the Federal Government of Nigeria promotes environmentally friendly operations of OEE. Future studies should focus on PAH pollution in farmlands, ambient air and the associated human and ecological health risks.

Water and water habitats are essential to life and to the wellness of the communities that rely on them, as the Danube river is subject to human impact and vice versa, periodic surveys are required to determine the status of its pollution levels. In this work we used known microbiological indicators as well as physico-chemical ones to assess the ecotoxicological status of the Danube river from eleven locations partially forming the “Romanian–Bulgarian Danube Sector”. Most of the microbial communities found, and their densities, could be explained by point and diffuse sources scattered along the sector such as discharged household and farm wastewater, as well as nearby agricultural areas where fertilizers have been used and then leaked in the water stream during rainfalls. However, microbial data on non-point sources that lead to diffuse pollution of surface waters could be linked to such parameters and furthermore shown a slight correlation with the current status of fish communities.

Microplastics are a fast emerging group of contaminants. Their worldwide occurrence in water, sediment, and aquatic fauna raises questions and concerns as to their probable effects on aquatic life and ecology. This study investigates for the first time presence, abundance, and types of microplastics in water and sediment from a lagoon bordering the large urban agglomeration of Lagos in Nigeria, and renders additional information about grain size and sediment composition. Water and sediment samples were collected from four locations in the Lagos lagoon and a tributary. The abundance and distribution of microplastics in four range classes were determined for the sampled locations. Plastic particles were counted using digital microscopy, and identified with FTIR and pyrolysis GC-MS. The abundance of microplastics ranged from 310-2319 microplastic particles/kg in sediment, and 139-303 particles/m³ in water. The large discrepancy in the sediments can be explained by sediment characteristics as more microplastics were detected in the fine-grained sediments of Makoko. Fibres were the predominant shape found in all samples followed by fragments and few films whereas spheres were missing. Fibres were more abundant in water (92.6 %) than in sediments (32.5 %) while more fragments and foils occurred in sediments. The most commonly used polymers polypropylene and polyethylene were also the most detected ones in both matrices. Compared to other studies in Nigeria, our findings especially in the coarser sediments were lower while the fine-grained site revealed similar results.

Heavy metals have been implicated as Lagoon pollutants from sources such as agriculture, mining and manufacturing industries and waste water treatment works. A study was carried out in the University of Lagos lagoon to investigate the seasonal bioavailability of the heavy metal contaminants Cd, Cr, Cu, Pb and Zn. The physical parameters pH, redox potential, temperature, TDS and conductivity were measured on site. Dried sediment samples were extracted using the Community Bureau of Reference (BCR) sequential procedure and analysed by ICP-OES. A certified reference material (CRM), BCR 701 (lake sediment) was used for quality assurance with recoveries ranging between 80-120%. Statistical analysis (ANOVA) showed that there was a significant difference between metal distribution in the dry and wet seasons. Cu, Pb and Zn were in the available fractions (carbonate, Fe/Mn oxide and organic). Cu was highest in the Fe/Mn oxide and organic fractions. This indicated that an increase in organic matter and reducing agents will avail the Cu. Zn was distributed in all fractions while Pb was found in the Fe/Mn oxide fraction (3.93- 21.3 %). Results showed that the bioavailability of Cu, Pb and Zn was high. Metal bioavailability by BCR indicates a potential risk of pollution in lagoon sediments as the available metals exceeded the permissible Sediment Quality Assessment Guidelines (SQAG’s) from Environmental Protection Agency (EPA).

The river Teign in Devon has come under scrutiny for failing to meet Environmental Quality Standards for ecotoxic metals due to past mining operations. A disused mine known as Bridford Barytes mine, has been found to contribute a significant source of Zn, Cd and Pb to the river. Recently, studies have been focused on the remediation of such mine sites using low-cost treatment methods to help reduce metal loads to the river downstream. Red mud is a waste product from the aluminium industry, the utilization of this resource has proven an attractive low-cost treatment method for adsorbing toxic metals. Adsorption kinetics and capacity experiments reveal metal removal efficiencies of up to 70% within the first 2 hours when red mud is applied in pelletized form. Biochar is another effective adsorbent with the potential to remove >90% Zn using agricultural feedstock. Compliance of the Teign has been investigated by analysing dissolved metal concentrations and bioavailable fractions of Zn to assess if levels are of environmental concern. By applying a Real-World Application Model, this study reveals that compressed pellets and agricultural biochar offer an effective, low-cost option to reducing metal concentrations and thus improving the quality of the river Teign.

India is one of the large sources of the anthropogenic pollutants and their increasing emission due to the recent economic growth in India. In this study we analyzed the annual and seasonal behaviors of ozone (O₃) gas using satellite remote sensing dataset from the sources Ozone Monitoring Instrument (OMI) over India region from 2006-2015. The study focuses on the seasonal behaviors of O₃ gas i.e., monthly, seasonal, annual mean variations of trace gas and also trend analysis of O₃ gas and comparison of the seasonal behavior of the ozone gas by trend analysis were assessed. In this study we also taken eleven cities to show the increment and decrement in four seasons of O₃ gas by taking 2006 as a base year and investigate the behaviors of gases during (2007-2015) years. Higher concentrations of O₃ south-to-north gradient, indicating the variations due to the impact of emissions and local meteorology. Ozone concentrations were higher during the warmer months. However, in winter season lowest concentration of O₃ seen due to the less amount of heat and due to cold days and ozone holes in the stratosphere. Instead, total O₃ concentrations rises over Delhi, Lucknow and Kolkata due to large population density, high traffic emission, highly polluted air and larger industrial activities.

Background: Covid-19 was first reported in Wuhan, China in Dec 2019. Since then, it has been transmitted rapidly in China and the rest of the world. While Covid-19 transmission rate has been declining in China, it is increasing exponentially in Europe and America. Although there are numerous studies examining Covid-19 infection, including an archived paper looking into the meteorological effect, the role of outdoor air pollution has yet to be explored rigorously. It has been shown that air pollution will weaken the immune system, and increase the rate of respiratory virus infection. We postulate that outdoor air pollution concentrations will have a negative effect on Covid-19 infections in China, whilst lockdowns, characterized by strong social distancing and home isolation measures, will help to moderate such negative effect. Methods: We will collect the number of daily confirmed Covid-19 cases in 31 provincial capital cities in China during the period of 1 Dec 2019 to 20 Mar 2020 (from a popular Chinese online platform which aggregates all cases reported by the Chinese national/provincial health authorities). We will also collect daily air pollution and meteorology data at the city-level (from the Chinese National Environmental Monitoring Center and the US National Climatic Data Center), daily inter-city migration flows and intra-city movements (from Baidu). City-level demographics including age distribution and gender, education, and median household income can be obtained from the statistical yearbooks. City-level co-morbidity indicators including rates of chronic disease and co-infection can be obtained from related research articles. A regression model is developed to model the relationship between the infection rate of Covid-19 (number of confirmed cases/population at the city level) and outdoor air pollution at the city level, after taking into account confounding factors such as meteorology, inter- and intra-city movements, demographics, and co-morbidity and co-infection rates. In particular, we shall study how air pollution affects infection rates across different cities, including Wuhan. Our model will also study air pollution would affect infection rates in Wuhan before and after the lockdown. Expected findings: We expect there be a correlation between Covid-19 infection rate and outdoor air pollution. We also expect that reduced intra-city movement after the lockdowns in Wuhan and the rest of China will play an important role in reducing the infection rate. Interpretation: Infection rate is growing exponentially in major cities worldwide. We expect Covid-19 infection rate is related to the air pollution concentration, and is strongly dependent on inter- and intra-city movements. To reduce the infection rate, the international community may deploy effective air pollution reduction plans and social distancing policies.

Microorganisms drive the biogeochemical cycles that link abiotic and biotic processes in the aqueous environment and are intricately associated with plastic debris. The detection of microplastics in water and sediment introduces new concerns as small particle size allows for yet unconsidered pathways for plastics in the food web and element cycles. In this review, we present current knowledge of microbe-plastic interactions and summarize the potential impact of biogeochemical processes on plastic distribution, cycling, transport, and sedimentation. We explore how microbe-plastic interactions influence the exposure of consumers to plastics and plastic degradation products. Key methods used to elucidate biofilm development, microbial biodegradation, and plastic detection in the aqueous environment are discussed. Finally, we comment on potential future questions and research directions needed to further define the role of microorganisms in the environmental fate of microplastics.

A recent study found that a 3ppb increase in O₃ ambient concentration was associated with an increased progression of 0.18 percentage points in percent emphysema and that such increase was equal to smoking 20 cigarettes per day for 29 years. A simple estimation of population attributable fraction shows that COPD diagnoses due to smoking are actually 30 times more than those attributed to a 3 ppb increment in O₃ concentration. Labelling ozone pollution as the new smoking may distort perception of the risks and hinder proper response to real life threatening risk such as smoking.

Because of the widespread use of bisphenol analogues (BPs) as the alternatives to bisphenol A (BPA), they have attracted considerable attention for health risk in aquatic ecosystems. The occurrence and distribution of six BPs were researched in soluble phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. Except for bisphenol Z, all BPs were detected in the two or three phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the soluble phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the soluble and colloidal phases, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude higher than SPM, suggesting that colloids have an obvious impact on regulating BPs’ environmental behaviors. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

Owing to the widespread use of bisphenol analogues (BPs) as bisphenol A (BPA) alternatives, they have been recognized to constitute a health risk for aquatic ecosystems. The occurrence and distribution of six BPs were investigated in the truly dissolved phase (< 5 kDa), colloidal phase (5 kDa to 1 µm) and suspended particulate matter (SPM > 1 µm) in a water diversion project of Nanjing, China. With the exception of bisphenol Z, all BPs were detected in at least two phases, the total concentrations of detected BPs were 161-613 ng/L, 5.19-77.2 ng/L and 47.5-353 ng/g for the truly dissolved phase, colloidal phase and SPM, respectively. Among the detected compounds, BPA still the dominant BPs in the truly dissolved phase and colloidal phase, followed by BPS, while BPAF was the major contaminant in SPM, followed by BPA. The mean contribution proportions of colloids were 1-2 orders of magnitude greater than that of SPM, suggesting that colloids play an important role in regulating the environmental behaviors of BPs. In terms of spatial distribution, although the water diversion project could reduce the pollution levels of BPs, which might further affect the ecological security of the Yangtze River.

The study of the distribution and health risk assessment is meaningful to provide basic data for environmental management．To investigate the pollution of potential toxic organics and their health risk to human beings, water samples were collected at 7 sites of main surface water of Beijing during wet and dry seasons respectively. The targeted 92 organics were detected, including phthalates (PAEs), volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs) and phenols. The results showed that: there were 56 organics detected out, and the number ratios of detected compounds to the total compounds of the same kind increased as the following: VOCs, phthalates, phenols, PAHs. 8 VOCs were detected in wet season, and 3 in dry season. The concentration of 2,2-Dichloropropane was highest as 10.62ug/L, while the concentrations of other VOCs were below 5ug/L; There were 11 phthalates detected during dry season. The content of Bis(2-methoxyethyl) phthalate was highest as 188.47ng/L; 17 phenols were found in samples during wet season, and the highest concentration was 1244.73ng/L for 4-nitrophenol; PAHs could be detected in all samples, and the detected compounds and the corresponding average concentrations were higher in wet seasons than those in dry seasons, which indicated that non-point pollution was possibly the main pollution source. The health risk assessment of the detected 56 pollutants by using a model from US EPA showed that, the risk caused by the four kinds of toxic organics in this study was in the acceptable ranges.

This study evaluated the physicochemical, mineralogical properties, mobile chemical species’ bioavailability and translocation in Brassica juncea and Spinacea oleracea L plants of a South African coal fired power utility. Coal fly ash (CFA) disposal is associated with various environmental and health risks including air, soil, surface and ground water pollution due to the leaching of toxic chemical species; these ends up in food webs affecting human health, while repeated inhalation causes bronchitis, silicosis, hair loss and lung cancer. The morphology, chemical, and mineralogical composition of CFA were determined using Scanning Electron Microscopy (SEM), X-ray fluorescence (XRF) and X-ray Diffraction, respectively. In pot culture experiments, S. oleracea L and B. juncea plants were grown in three sets of pots containing CFA (set 1), soil (set 2) and a mixture of CFA plus soil at ratio 1:1 (50% CFA: 50% soil) (set 3), while no plants were grown in set 4 as a control for the leachate samples. SEM showed that surface morphology of CFA has a lower degree of sphericity with irregular agglomerations of many particles. The XRF results revealed that CFA contains 43.65%, 22.68% and 10.89% of SiO₂, Al₂O₃ and Fe₂O₃ respectively which indicate that the CFA is an alumino-silicate material. While XRD showed that the coal CFA contains mullite as a major phase followed by quartz mineral phases. Chemical species such as Fe, Mn, B, Ba and Zn were accumulated highly in most parts of the plant species. However, B. juncea showed higher potential to accumulate chemical species as compared to S. oleracea L. The bioconcentration and translocation factors (BF and TF) showed that B. juncea was the most effective in terms of bioconcentration and translocation of most of the chemical species. This indicates that B. juncea has potential in application for phytoremediation of CFA dumps and could contribute to remediation of CFA dumps and reduction of potential health and environmental impacts associated with CFA.

The Bay of Espirito Santo is located in the Espírito Santo State, in the eastern part of Brazil. It is surrounded by the city of Vitoria on one side and by the Atlantic Ocean on the other. Superficial sediments of Espirito Santo Bay were analyzed at 12 (western shallow silt sediments) + 8 (eastern sandy sediments and relatively deep sampling stations) = 20 uniformly distributed sampling points where geochemical analysis was performed. Nineteen elements were analyzed: Mo, Cu, Pb, Zn, Ag, Ni, Mn, Fe, As, U, Th, Sr, Cd, Sb, Bi, V, Cr, Ba, and Al. This selection was made based on the most representative heavy metals present in this area and according to the results obtained from the geochemical analysis. Their concentrations were compared with metal contamination benchmarks like Screening Quick Reference Tables (SQuiRTs), Effects Range-Low (ERLs) and Effects Range-Median (ERMs), TELs (Threshold Effects Levels), PELs (Probable Effects Levels), ERM (Effects range median), and AETs (Apparent Effects Thresholds). Results indicate that there is no particular pollution condition able to alter the condition of any part of this water body. The Authors conclude that the Espirito Santo Bay is only moderately polluted and some elements are virtually absent.

The Bay of Espirito Santo is located in the Espírito Santo State, in the eastern part of Brazil. It is surrounded by the city of Vitoria on one side and by the Atlantic Ocean on the other. Superficial sediments of Espirito Santo Bay were analyzed at 12 (western shallow silt sediments) + 8 (eastern sandy sediments and relatively deep sampling stations) = 20 uniformly distributed sampling points where geochemical analysis was performed. Nineteen elements were analyzed: Mo, Cu, Pb, Zn, Ag, Ni, Mn, Fe, As, U, Th, Sr, Cd, Sb, Bi, V, Cr, Ba, and Al. This selection was made based on the most representative heavy metals present in this area and according to the results obtained from the geochemical analysis. Their concentrations were compared with metal contamination benchmarks like Screening Quick Reference Tables (SQuiRTs), Effects Range-Low (ERLs) and Effects Range-Median (ERMs), TELs (Threshold Effects Levels), PELs (Probable Effects Levels), ERM (Effects range median), and AETs (Apparent Effects Thresholds). Results indicate that there is no particular pollution condition able to alter the condition of any part of this water body. The Authors conclude that the Espirito Santo Bay is only moderately polluted and some elements are virtually absent.

Air pollution has become a growing invisible killer in recent years and is major cause of morbidity and mortality globally. India stands 10th among the highly polluted countries with an average PM10 level of 134μg/m3 per year. It is also reported that 99% of India's population comes across air pollution level that exceed the World Health Organization Air Quality Guideline (AQG), PM2.5 permissible levels of 10 μg/m3. Maternal exposure to air pollution has a serious health outcome to the offspring because it can affect embryonic phases of development during the gestation period. Fetus is more prone to air pollution effect during embryonic developmental phases due to oxidative stress as antioxidant mechanisms are lacking at that stage. Any injury during this vulnerable period (embryonic phase) will have long-term impact on offspring health both in early and later in life. Epidemiological studies have revealed that maternal exposure to air pollution increases the risk of developing airways disease in offspring due to impaired lung development in utero. In this review, we discuss cellular mechanisms involved in maternal exposure to air pollution and how it can impact development of airways disease in offspring. Better understanding of these mechanisms in context of maternal exposure to air pollution can offer newer avenue to prevent development of airways disease in offspring.

Abstract: The frequency and intensity of air pollution are two of most critical issues the world faces in dealing with global environmental problems. They are both important areas that need to be improved. Our previous research [20] examines the assessment of fine dust pollution in Baekryeong island by statistical reasoning through one specific example of inland city (Yanggu) in Republic of Korea; however, given that Baekryeong Island is a remote island, there has been little focus on in-depth examination of its effect on the high density of fine dust in Baekryeong Island. The purpose of this article is twofold: (i) to examine the effect of a remote island on the high density of fine dust on Baekryeong Island using statistical reasoning and to provide a more specific statistical basis for the claim that one of the non-negligible factors influencing the high density of fine dust on Baekryeong Island is the geographic proximity to China; and (ii) to present brief discussion of fundamental cause of fine dust and global air pollution issues, which are not discussed in [20].

The air is not the same as thousands and hundreds of years ago. In the air, suspended particles originate from natural phenomena like dust storms or volcanic activities, as well as anthropogenic pollutants such as fuel engine exhaust and everyday activities at home. The total particles in the air can be classified by sizes, such as PM10, PM2.5 or ultrafine particles. However, there are many other important factors in addition to the particle size, influencing the particle behavior and affecting our health. The surface area, chemical and biological composition, aspect ratio, and the charge are all factors characteristic of particles. OoC microfluidic chips are very useful for the pollutant toxicity measurements on various body tissues. A better understanding of pollutants will help to trace these to the potential sources. The data from the on-the-ground and satellite monitoring can be integrated into models, helping to predict and prevent pollution exposure.

The current study aimed to: i) Monitor levels of PM₁₀, at Shebika, Haram, Masfala, Azizia, Awali and Mina in Makkah city, KSA during the period of 01 Shawwal 1436H – 27 Rabi Al-Awwal 1437H, by using LVS instruments; and; 2) assess health risk (non-cancer and cancer risks) on humans (children and adult) exposed to PM₁₀ in ambient air of Makkah city.The results showed that: the high PM₁₀ levels were found in Haram site, while the lower levels were found in Awali site. These levels were lower than that set for PM₁₀ by PME (Daily limit of 340 µg/m³). Vehicles emissions and constructions sources may be the main source of PM₁₀ levels in Makkah city. The human health risk assessments showed that: the daily exposure doses of PM₁₀ were ranked in the order: D_ing > D_dermal > D_inh for children and adult in Makkah city. Ingestion of PM₁₀ particles was the main exposure pathway for both children and adults. The HIs and cancer risk values were within the safe level, indicating that (non-carcinogenic and carcinogenic) risks for humans exposed to PM₁₀ in Makkah city were negligible.

Whereas waste management research has focused on mostly urban municipalities in South Africa, not much is known about the current performance of waste management services from the perspective of community residents in rural municipalities. This study reports on the status and effectiveness of waste management practices from the perspective of community residents in the Umkhanyakude and Zululand Districts in the rural areas of the KwaZulu-Natal province of South Africa. Making use of structured questionnaires, primary data was obtained by interviewing 333 respondents representing households in the study area. Results have revealed several shortfalls in the provision of municipal waste management services, except for solid waste removal from households (66%), and management of landfill sites (41%). The degree of dissatisfaction for waste management services rendered was very high (97.3%). Furthermore, the majority (61.4%) of respondents were not willing to participate in waste segregation due to lack of appropriate knowledge and infrastructure. The study also pinpointed some benefits associated with waste minimization, as well as barriers constraining effective waste recycling. Based on these findings, there is a dire need for transforming current waste management practices toward increased recycling rates by creating more environmental awareness and a supporting infrastructure.

In this study, the causal-effect between carbon dioxide emissions and forestry production and trade was investigated in Ghana by employing a data spanning from 1961 to 2014 by using the VECM and ARDL model. Evidence of the long-run equilibrium relationship in the VECM shows that, a 1% increase in veneer sheet production reduces carbon dioxide emissions by 1.47% in the long-run. There was evidence of a bidirectional causality between carbon dioxide emissions and veneer sheet production, carbon dioxide emissions and wood charcoal production, and a unidirectional causality running from carbon dioxide emissions to wood fuel production and plywood production to carbon dioxide emissions. Evidence from the long-run equilibrium relationship in the ARDL model shows that; a 1% increase in plywood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in sawnwood production will increase carbon dioxide emissions by 0.17% in the long-run, a 1% increase in wood charcoal production will increase carbon dioxide emissions by 0.36% in the long-run and a 1% increase in wood fuel production will increase carbon dioxide emissions by 0.37% in the long-run.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.