The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

Cement production requires a significant amount of energy and natural resources, severely impacting the environment due to harmful gas emissions. Coal Bottom Ash (CBA) and Coal Boiler Slag (CBS), byproducts of coal-fired power plants, have pozzolanic properties. CBA and CBS can be mechanically ground to obtain Ground Coal Bottom Ash (GCBA) or Ground Coal Bottom Slag (GCBS), which can potentially replace cement in concrete, reducing waste in landfills, benefit the economy, preserving natural resources, and reducing health hazards. This study was performed to determine the optimum amount of GCBA and GCBS that can replace cement in concrete. The fresh, mechanical, and durability properties of the concrete containing GCBA were compared to a control mix consisting of 100% Portland cement. The optimum amount of cement replaced with GCBA and GCBS was 10% and 5%, respectively, based on compressive strength. The GCBA-based concrete's tensile strength, modulus of elasticity, and durability properties were better than the control. The compressive strength of the GCBA and GCBS-based mortars increased with an increase in fineness. GCBA and GCBS fineness should be within the limit recommended in the ASTM C618 standard to enhance concrete or mortar properties.

Experimental quantification of retention factors related to post-fire strength as well as post-fire ductility of intentionally selected stainless steel grades applied in construction is the objective of research presented here. These steel grades are characterized by a two-phase austenitic-ferritic microstructure of the duplex type. In this context two mutually corresponding chromium-nickel-molybdenum steel grades have been subjected to analysis, namely X2CrNiMoN22-5-3 steel belonging to the standard duplex group (DSS 22% Cr) and X2CrMnNiN21-5-1 steel belonging to the lean duplex group (LDSS). The similarities and differences in the mechanical properties exhibited by these steel grades after effective cooling, following more or less prolonged simulated fire action conforming to several development scenarios, have been identified and indicated. The resistance of given steel grade to permanent structural changes induced by the heating program proved to be the critical factor determining these properties and resulting in many cases in increased susceptibility to brittle fracture.

Fly ash cement has rarely been used in Japan, mainly because its strength development is slower than ordinary Portland cement. In this research, the effect of the new fly ash cement with both high alite (C3S) cement and fly ash modified by electrostatic belt separation method on cracking resistance of precast concrete prepared by steam curing was studied. The mechanical and shrinkage properties of the proposed fly ash concrete were compared with those of concrete made using OPC cement without fly ash. In order to study the cracking tendency of precast concrete with the proposed fly ash cement, thermal stress analysis was conducted taking into consideration of the experimental data of concrete properties with the different concrete mix proportions. A standard precast concrete box culvert model was used in this 3D FEM analysis and the distribution of temperature and relative humidity in cross section and induced restraint stress during and after steam curing were discussed. Steam-cured concrete with fly ash and high alite cement developed higher compressive strength on the first day of age than concrete with OPC. The proposed fly ash concrete developed high cracking resistance in the early days. On the other hand, the results showed that the drying shrinkage at later ages was the main cause of cracking.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

Sex dimorphism starts during early embryogenesis and is further manifested in response to hormones during puberty. As this leads to physical divergence that is measurably different between sexes, males enjoy physical performance advantages over females within competitive sport. While this advantage is the underlying basis of the segregation into male and female sporting categories, these sex-based categories do not account for transgender persons who experience incongruence between their biological sex and their experienced gender identity. Accordingly, the International Olympic Committee determined criteria by which a transgender woman may be eligible to compete in the female category, requiring total serum testosterone levels to be suppressed below 10 nmol/L for at least 12 months prior to and during competition. Whether this regulation removes the male performance advantage has not been collectively scrutinized. Here, we aim to review how differences in biological characteristics between biological males and females affect sporting performance and assess whether evidence exists to support the assumption that testosterone suppression in transgender women removes the male performance advantage. In this review, we report that the performance gap between males and females amounts to 10-50% depending on sport. The performance gap is more pronounced in sporting activities relying on muscle mass and strength, particularly in the upper body. Longitudinal studies examining the effects of testosterone suppression on muscle mass and strength in transgender women consistently show very modest changes, where the loss of lean body mass, muscle area and strength typically amounts to approximately 5% after 1 year of treatment. Thus, current evidence shows that the biological advantage enjoyed by transgender women is only minimally reduced when testosterone is suppressed. Sports organizations may therefore be compelled to reassess current policies regarding participation of transgender women in the female category of sport.

The study presents a comparative approach between response surface methodology (RSM) and hybridized, genetic algorithm artificial neural network (GA-ANN) in predicting the water absorption, compressive strength, flexural strength split tensile strength and slump for steel fiber reinforced concrete. The effect of process variables such as aspect ratio, water cement ratio and cement content were investigated using the central composite design of response surface methodology. This same experimental design was used in training the hybrid-training approach of artificial neural network. The predicting ability of both methodologies were compared using the root mean sqaured error (RMSE), mean absolute error (MAE), model predictive error (MPE) and absolute average deviation (AAD). The RSM model was found more accurate in prediction compared to hybrid GA-ANN.

In India, particularly within its North-Eastern territories, the occurrence of landslides triggered by post-dry period rainfall events is a significant concern, with the phenomena persistently causing extensive damage to both life and infrastructure. Despite the inevitability of such natural disasters, it is understood that the impact they exert can be substantially mitigated through the implementation of pre-emptive measures. Critical to the endeavour of landslide prevention is the application of a spectrum of mitigation strategies, predicated upon a foundational analysis of slope stability to ascertain critical surfaces for intervention. This investigation delves into the dynamics of partially saturated soils, a condition commonly resultant from the prolonged dry periods preceding the monsoonal rains. The study's focal point is an experimental examination conducted on soil samples to assess parameters such as soil matric suction and unconfined compressive strength across varying degrees of saturation and density, alongside performing analyses of slope failure incidents after dry period during the 2017 monsoon in the Lunglei district, Mizoram based on some established data. The Soil-Water Characteristic Curve (SWCC), derived from soil suction measurements employing the ASTM D5298-10 standard, utilizes a contact filter paper method and serves to delineate the moisture transition phases of the slope. To replicate the desiccation of the soil slope after monsoonal rains, a microwave drying technique based on the ASTM standard was employed to prepare unsaturated soil samples for Unconfined Compressive Strength (UCS) testing. The integrity of the slope was evaluated in a temporal context, before and after rainfall events of varied intensities throughout the calendar year, utilizing a blend of numerical modeling and empirical laboratory investigations. The persistence of real onsite slope failures underscores the necessity for a numerical analysis approach to unravel the underlying factors causing slope instability, especially given the absence of prior stability assessments for the landslide in question. An evaluation of SWCC curves, UCS tests on partially saturated soil at different densities and saturation and the utilization of the benchmark data collected in 2017 on the shallow transitional landslide in Lunglei, Mizoram caused by intense monsoonal precipitation, are central key data and information used to carry out this research. Rainfall data for Lunglei, sourced from the Mizoram Meteorological Department, facilitated a real-time monsoonal data-driven numerical analysis. This analysis elucidated the pivotal role of rainfall in inducing slope failure, indicating a marked destabilization of the slope after precipitation events. The implications of these findings are far-reaching, suggesting a foundational basis for the development of an advanced landslide early warning system, thereby enhancing disaster preparedness, and mitigating potential damages.

The functional capacity of the cervical spine plays a central role in healthy living. This study evaluated and created a comprehensive strength, range of motion (ROM), and musculoskeletal pain profile of the cervical spine in young adults. 60 physically active individuals (30 males/30 females; 19-24 year-old) participated in the study. Cervical ROM (forward flexion, extension, lateral flexion, and rotation), maximal isometric strength (forward flexion, extension, lateral flexion), and musculoskeletal pains were assessed using an electronic goniometer, a handheld dynamometer, and the Nordic questionnaire, respectively. Data analysis revealed that: a) fe-males had higher ROM values, during extension and lateral flexion, than males (p<0.05), b) males had higher absolute strength values than females in all movement directions, higher rela-tive strength values/body mass (at forward flexion) and flexion/extension ratio values (p<0.05), c) ROM and strength values were not significantly different between right-left sides (p>0.05), d) a great proportion (43.3%) of the participants had cervical pains (no sex-related differences) and e) cervical strength showed significant small negative correlation with pains (p<0.05; r=-0.225 to -0.345). The reference values created may be used by health and fitness professionals to exten-sively evaluate the cervical spine and to design specific exercise programs for injury prevention and rehabilitation.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

The relative force strengths of the Coulomb forces, gravitational forces, dark matter forces, weak forces and strong forces are compared for the dark matters, leptons, quarks, and normal matters (p and n baryons) in terms of the 3-D quantized space model. The quark confinement and asymptotic freedom are explained by the CC merging to the A(CC=-5)₃ state. The proton with the (EC,LC,CC) charge configuration of p(1,0,-5) is p(1,0) + A(CC=-5)₃. The A(CC=-5)₃ state has the 99.6% of the proton mass. The three quarks in p(1,0,-5) are asymptotically free in the EC and LC space of p(1,0) and are strongly confined in the CC space of A(CC=-5)₃. This means that the lepton beams in the deep inelastic scattering interact with three quarks in p(1,0) by the EC interaction and weak interaction. Then, the observed spin is the partial spin of p(1,0) which is 32.6 % of the total spin (1/2) of the proton. The A(CC=-5)₃ state has the 67.4 % of the proton spin. This explains the proton spin crisis. The EC charge distribution of the proton is the same to the EC charge distribution of p(1,0) which indicates that three quarks in p(1,0) are mostly near the proton surface. From the EC charge distribution of neutron, the 2 lepton system (called as the koron) of the koron is, for the first time, reported in the present work.

Bamboo is considered a sustainable construction material due to its ability to grow quickly and its mechanical properties that are comparable to timber. Contributing to the current effort to establish the structural bamboo standards in the National Structural Code of the Philippines (NSCP), this study establishes the characteristic compressive strength of four bamboo species: Bambusa vulgaris (36 samples), Dendrocalamus asper (36 samples), Bambusa blumeana (94 samples), and Guadua angustifolia Kunth (30 samples). The samples were subjected to compressive loading following ISO 22157-1 (2017). The characteristic compressive strength values obtained, according to ISO 12122-1 (2014), were 40.35 MPa for B. vulgaris, 40.21 MPa for D. asper, 46.63 MPa for B. blumeana, and 36.99 MPa for G. angustifolia Kunth. Simple linear analysis, One-way ANOVA, and Welch’s t-Test were used to analyze the correlation models and establish a comparative analysis of the effect of nodes, and geometric and physical properties on the compressive strength of bamboos. Comparing the characteristic compressive strength obtained from this study to the strength of unseasoned structural timber of Philippine woods, all bamboo species showed higher strength values, and thus have great potential as an alternative construction material to timber.

In this paper, we will use the maximum likelihood estimation (MLE) and the Bayes methods to perform estimation procedures for the reliability of stress-strength ℜ=P[X>Y] based on independent adaptive progressive censored samples that were taken from the Chen distributions. An approximate confidence interval of ℜ is constructed using a variety of classical techniques, such as the normal approximation of the MLE, the normal approximation of the log-transformed MLE, and the percentile bootstrap (Boot-p) procedure. The Bayesian estimation of ℜ is obtained based on the balanced loss function, which comes in two versions here, the symmetric balanced squared error (BSE) loss function and the asymmetric balanced linear exponential (BLINEX) loss function. When estimating ℜ using the Bayesian approach, all the unknown parameters of the Chen distributions are assumed to be independently distributed and to have informative gamma priors. Further, a mixture of Gibbs sampling algorithm and Metropolis-Hastings algorithm is used to compute the Bayes estimate of ℜ and the associated highest posterior density credible interval. In the end, simulation research are used to assess the general overall performance of the proposed estimators and a real data set is provided to exemplify the theoretical results.

In cricket, particularly the twenty20 format is most watched and loved by the people, where no one can guess who will win the match until the last ball of the last over. In India, The Indian Premier League (IPL) started in 2008 and now it is the most popular T20 league in the world. So we decided to develop a machine learning model for predicting the outcome of its matches. Winning in a Cricket Match depends on many key factors like a home ground advantage, past performances on that ground, records at the same venue, the overall experience of the players, record with a particular opposition, and the overall current form of the team and also the individual player. This paper briefs about the key factors that affect the result of the cricket match and the regression model that best fits this data and gives the best predictions. Cricket, the mainstream and widely played sport across India which has the most noteworthy fan base. Indian Premier League follows 20-20 format which is very unpredictable. IPL match predictor is a ML based prediction approach where the data sets and previous stats are trained in all dimensions covering all important factors such as: Toss, Home Ground, Captains, Favorite Players, Opposition Battle, Previous Stats etc, with each factor having different strength with the help of KNIME Tool and with the added intelligence of Naive Bayes network and Eulers strength calculation formula.

The radio operation in wireless sensor networks (WSN) in the Internet of Things (IoT) applications are the most common source for power consumption. However, recognizing and controlling the factors affecting radio operation can be valuable for managing the node power consumption. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS used in WakeUp mode, which is a clear channel assessment (CCA) to check radio status periodically. The time spent to check the radio is of utmost importance for monitoring power consumption. It can lead to false WakeUp or idle listening in Radio Duty-Cycles and ContikiMAC. This paper presents a detailed analysis of radio WakeUp time factors of ContikiMAC. Then, we propose lightweight CCA (LW-CCA) as an extension to ContikiMAC to reduce the percentage of Radio Duty-Cycles in false WakeUps and idle listenings by using dynamic received signal strength indicators (RSSI) status check time. The simulation results in the Cooja simulator show that LW-CCA reduces about 8% energy consumption in nodes while maintaining up to 99% of the packet delivery rate (PDR).

Background and objectives: Only a few studies analyzed the physical activity level of elderly people living alone in local communities and evaluated the relationship between it and mental health. The purpose of this study was to investigate the relationship between physical activity and depression in the elderly living alone and to provide basic data for the prevention of depression in the elderly. Materials and Methods: We analyzed 256 elderly people living alone aged 65 years or older who completed the 2014 Korea National Health and Nutrition Examination Survey. Depression was defined as a score of 10 or higher using Patient Health Questionnaire-10(PHQ-9). This study investigated walking per week, days of muscular strength exercise performance in the past one week, days of flexibility exercise in the past one week, mean hours in a sitting position per day, the numbers of days and hours conducting a high intensity physical activity in the past one week, and numbers of days and hours conducting a medium intensity physical activity in the past one week to define physical activity. Our study presented prevalence odds ratios (pOR) and 95% confidence interval (CI) by using complex sample logistic regression analysis in order to identify the relationship between physical activity and depression. Results: The results of complex sample logistic regression analysis showed that flexibility exercise was significantly related to depression (p <0.05). On the other hand, the mean hours in a sitting position per day, aerobic physical activity, walking, and muscular strength exercise were not significantly related to geriatric depression. Conclusions: The results of our study implied that persistent flexibility exercise might be more effective to maintain a healthy mental status than muscular strength exercise. A longitudinal study is required to prove the causal relationship between physical activity and depression in the old age.

This work investigates how the user-controlled parameters of the 3D printing process define temperature conditions on the boundary between layers of the part being fabricated and how these conditions influence the structure and strength of the part. The process studied is fused filament fabrication with a desktop 3D printer and the material utilized is PLA (polylactic acid). As a characteristic of the part strength the fracture load in the case of a three-point bend and calculated related stress were used. During the printing process parts were oriented with the long side along the Z axis, thus, in the bend tests, the maximum stress occurred orthogonally to the layers. During the fabrication process, temperature distribution on the sample surface was monitored with thermal imager. Sample mesostructure was analyzed using SEM. The influence of the extrusion temperature, the intensity of part cooling, the printing speed and the time between printing individual layers were considered. The influence of all the parameters can be expressed through two generalizing factors: the temperature of the previous layer and the flow efficiency, determining the ratio of the amount of extruded plastic to the calculated. A regression model was proposed that describes the effect of the two factors on the printed part strength. Along with interlayer bonding strength, these two factors determine the formation of the part mesostructure (the geometry of the boundaries between individual threads). It is shown that the optimization of the process parameters responsible for temperature conditions makes it possible to approximate the strength of the interlayer cohesion to the bulk material strength.

The current paper is studying the influence of geometrical parameters of the FDM (FFF) 3D printing process on printed part strength for open source desktop 3D printers and the most popular material used for that purpose, i.e. PLA (polylactic acid). The study was conducted using a set of different nozzles (0.4, 0.6 and 0.8 mm) and a range of layer heights from the minimum to maximum physical limits of the machine. To assess print strength, a novel assessment method is proposed. A tubular sample is loaded in the weakest direction (across layers) in a three-point bending fixture. To explain the results obtained, a mesostructure evaluation through SEM scans of the samples were used. A significant influence of geometric process parameters was detected on sample mesostructure and, consequently, on sample strength.

The Mann-Whitney effect is a measure for comparing survival distributions between two groups. The Mann-Whitney effect is interpreted as the probability that a randomly selected subject in a group survives longer than a randomly selected subject in the other group. Under the independence assumption of two groups, the Mann-Whitney effect can be expressed as the traditional integral formula of survival functions. However, when the survival times in two groups are not independent each other, the traditional expression of the Mann-Whitney effect has to be modified. In this article, we propose a copula-based approach to compute the Mann-Witney effect with parametric survival models under dependence of two groups, which may arise in the potential outcome framework. In addition, we develop a Shiny web app that can implement the proposed method via simple commands (https://nkosuke.shinyapps.io/shiny_survival/). Through a simulation study, we show the correctness of the proposed calculator. We apply the proposed methods to two real datasets.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

We investigate new graph characteristics namely total (vertex, edge) face irregularity strength of gen- eralized plane grid graphs Gmn under k-labeling Phi of type (Alpha, Beta, Gamma). The minimum integer k for which a vertex-edge labelled graph has distinct face weights is called the total face irregularity strength of the graph and is denoted by tfs(Gmn). In this article, the graphs G = (V;E; F) under consideration are simple, finite, undirected and planar. We will estimate the exact tight lower bounds for the total face irregularity strength of some families of generalized plane grid graphs.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

The radio activity in Wireless Sensor Networks (WSN) and Internet of Things (IoT) applications are the most common reason for power consumption. However, recognizing and controlling the factors affecting radio activity can be valuable for managing node power. ContikiMAC is a low-power Radio Duty-Cycle protocol in Contiki OS that uses Clear Channel Assessments (CCA) to check radio status periodically. The time taken to check the radio in receive mode WakeUp, is one of the most important reasons for power consumption which in most the cases can lead to negative WakeUp in Radio Duty-Cycles and ContikiMAC especially. Here, we present a detailed analysis of idle listening time factors on the ContikiMAC. Then, we propose Light Weight CCA(LW-CCA) as an extension to ContikiMAC to reduce power consumption by reducing the radio check time in receive mode WakeUp’s, while maintaining up to 99% the Packet Delivery Rate (PDR). The simulation results show that the proposed method reduces significantly energy consumption in nodes compared to ContikiMAC and thus it helps maintain a high network performance.

Throughout this paper the effects of injuries on athletes are highlighted in different aspects. Exertional compartment syndrome is a specific injury related to athletes that is thoroughly explored in this paper through an analysis of the anatomy, symptoms, diagnosis and treatments of the syndrome. Exertional compartment syndrome is an exercise-induced muscle and nerve condition that causes pain, swelling as well as disability in the affected muscles of the lower leg. This syndrome commonly develops in young athletes involved in sports with excessive running and repetitive impact such as track and field, soccer, basketball and lacrosse. Exertional compartment syndrome is commonly misdiagnosed as other less severe injuries such as shin splints, which is symptomatic of pain along the tibia bone of the lower leg caused by overuse. The misdiagnosis of exertional compartment syndrome allows the syndrome to worsen and intensify resulting in the only effective treatment to be fasciotomy, a surgical procedure to release the pressure within the compartment of the lower leg. There is no definitive protocol developed for patients after fasciotomy is performed. Athletes experiencing similar symptoms after surgery are usually treated for their symptoms rather than the syndrome as a whole, which does not have a high degree of success. The development of a definitive protocol utilizing the techniques of manual therapy, mobility stretching and corrective strength training can improve the adverse effects of exertional compartment syndrome as well as restore functionality to the athlete. Raising awareness of this syndrome in athletics will be effective in treating the athlete early on in order to avoid severe effects and invasive procedures.

Bare slope instability is a prevalent concern. The root system of, herbaceous vegetation enhances the shear strength of shallow–slope soil. Indoor experiments were conducted on rootless undisturbed soil (RUS) and undisturbed soil with a root system (USRS) using a triaxial compression apparatus to analyze the slope stability of composite soil with a Tagetes erecta root system. Significance tests and correlation analysis of the factors affecting shear performance were conducted using R software. The slope reinforcement, effect by the plant root system was simulated under 24 working conditions using the MIDAS finite element method. The results revealed the influence of the–root content (RC), moisture content (MC), and stress on the shear strength of USRS, the contribution degree, and the variables’ influences on slope stability. Both RUS and USRS exhibited strain hardening during shearing. The internal friction angle (φ) and cohesion (c) of USRS were negatively and positively correlated with the RC and MC (root burial depth), respectively, and a good fit was obtained for the relationship. The maximum deviatoric stress during shear failure was 1.29 times higher for USRS than for RUS. The RC (root depth) was positively correlated with the slope safety coefficient and the slope of the line under different working conditions, whereas the slope gradient was negatively correlated with the slope safety coefficient. The reinforcement effect by the root system resulted in a 13.2% increase in the safety coefficient and improved stability of slopes with a gradient larger than 1.5%. This article investigated the mechanism of the root–soil system and, the effects of different influencing factors on the shear strength of the soil, and slope stability. The findings provide new insights into shallow slope stability in practical slope protection projects.

Fiber reinforced thermoplastics (FRTP), which is reinforced with glass or carbon fibers, are used to improve the mechanical strength of injection-molded products. However, FRTP has problems such as the formation of weld lines, the deterioration of the appearance due to the exposure of fibers on the molded product surface, and the deterioration of the strength of molded products due to the fiber orientation in the molded products. We have designed and fabricated an injection mold capable of melt flow control and induction heating and cooling that has the functions of both heating and cooling the injection mold as well as the function of controlling the melt flow direction using a movable core pin. In this study, the above-mentioned mold was used for the molding of carbon fiber reinforced semi-aromatic polyamide. As a result, we found that increasing the heating temperature of the mold and increasing melt flow control volume contribute to the prevention of the generation of a weld line and the exposure of fibers on the molded product surface, as well as to the formation of a flat surface and increased bending strength. The relationships of these results with the carbon fiber orientation in the molded products and the crystallization of semi-aromatic polyamide were also examined in this study.

Breast cancer is the most common malignant disease in women. Preclinical studies have confirmed that the local anesthetic levobupivacaine has a cytotoxic effect on breast cancer cells. We examined whether postoperative wound infiltration with levobupivacaine influences survival in 120 patients who were operated on for breast cancer and underwent quadrantectomy or mastectomy with axillary lymph node dissection. Groups with continuous levobupivacaine wound infiltration, bolus wound infiltration, and diclofenac analgesia were compared. Long-term outcomes examined were quality of life, shoulder disability, and hand grip strength (HGS) after one year, and survival after 5 and 10 years. Groups that had infiltration analgesia had better shoulder function compared to diclofenac after one year. Levobupivacaine PCA group had the best preserved HGS after 1 year (P=0.022). The most significant predictor of the 5-year outcome was HGS (P=0.03). Although the best survival after 5 and 10 years was registered in the bolus levobupivacaine group, statistical significance was not reached (P=0.36). The extent of the disease at the time of surgery is the most important predictor of long-term survival. A larger prospective clinical study could better confirm the effect of levobupivacaine wound infiltration on outcomes after breast cancer surgery observed in this pilot study. Trial number NCT05829707

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

The article presents results of research consisting in an attempt to assess the influence of temperature, heating time and cooling method on microstructure and residual strength properties of steel previously tempered during the production process. Simulated environmental conditions to which high-strength bolts, commonly used in steel construction, were subjected, were intended to reflect conditions of a natural fire that may occur in public facilities where the obligation to ensure safety of users and rescue teams is of key importance, also required by law. Furthermore, the tests carried out also comprised a simulated effect of a rescue and firefighting operation using shock, rapid cooling of some of the heated bolts. Samples cut out from the tested bolts, after they were properly prepared, were subjected to microstructural tests using light microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), phase analysis with the use of an X-ray diffractometer (XRD) and quantitative analysis of the microstructure involving, inter alia, measuring the surface area of grains, their equivalent diameter and mean diameter. As a result of the tests, considerable microstructure changes were identified occurring in the bolt material as a result of exposing it to fire conditions, leading to a change in key, from the point of view of structural safety, mechanical properties. The results of the microstructure tests were compared with the results of previous strength tests, including hardness of the material after the heat treatment and the residual tensile strength of the material Rm. A conducted comparative analysis showed a significant effect of all such factors as the temperature level of the simulated fire, its duration and the fire-fighting method on the mechanical properties of bolts. Results obtained were provided with required comments and the concept of using the microstructure for the post-fire assessment of steel structures was referred to.

Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

In road construction, before applying an asphalt or concrete surface, the ground must be compacted and stabilized. There are two basic methods of soil stabilization: in situ and in a stationary node (ex-situ). The method of performing stabilization in place (in-situ) is the most frequently used method due to its convenience and lower price. The most popular type of binder for stabilization is a hydraulic binder (most often cement and various ashes). Such stabilization is performed at a depth of 10-50 cm, achieving the desired load-bearing parameters. In order to improve them, various chemical additives for stabilization are often used, such as ion exchange compounds, additives based on sulfuric acid, additives based on vinyl polymers or even organic additives using lignosulfonates. However, the use of such additives is associated with much greater costs and environmental burden, resulting in seeking for cheaper and equally effective alternatives. The win-win situation would be for instance recycling the problematic waste-based materials that on one hand are landfilled or impossible to recycle and on the other hand cause problems for the waste producers. Therefore, an interesting issue is the production of stabilization additives from various types of waste materials. As a result of the extensive testing of various waste-based materials blends with soil, the mechanical (compressive strength after 7 and 28 days) and hydraulic (capillary rise, water absorption, frost resistance) soil properties were measured. The optimization process led to obtaining additives compositions ensuring the best strengthening and sealing properties. These were for sandy soil: Pure foil (wax emulsion), Pure foil (wax emulsion) + waste sulphuric acid, RDF from waste tires (wax emulsion), Pure foil (wax emulsion) + “by-pass” waste ash + NaOHx2 and for clayey soil: Pure foil (wax emulsion) + NaOH, Pure foil (wax emulsion) + waste sulphuric acid, Tequant, Pure foil (wax emulsion).

The dilatometer curves of continuous cooling transformation of 12Mn steel were measured with Formastor-FⅡthermal mechanical simulator．The steel's undercooled austenite phase continuous cooling transformation curves ( CCT curves) were established by means of the dilatometer method and the metallographic-hardness measurement method． The effect of cooling rate on microstructure and hardness of the steel was studied． CCT curve of test steel was simulated by JMatPro. The results show that the Ac1 and Ac3 of the experimental steel are 692 ℃ and 855 ℃ ; the microstructure obtained is made of ferrite，pearlite and bainite．The ferrite transformation and pearlite transformation occur at a slower cooling rate，in which the ferrite is dominant. When the cooling rate is greater than 4.25 ℃ / s bainite transformation happens．As the cooling rate increases，microstructure or grains become finer．The hardness of the tested steel with increasing cooling rate shows a trend of first fast increase and soon decrease．The simulation results are consistent with the measured CCT law. The high temperature mechanical properties of 12mn steel round billet were tested by gleeble-1500d thermal / mechanical simulator. The tensile strength, reduction of area and stress-strain curves of the billet were obtained in the range of 600-1300 ℃.

Obesity in adolescents combined with the increased exposure time to electronic devices, enhances a sedentary lifestyle and is linked to the risk of developing musculoskeletal injuries. The aim of this study was to identify possible correlations between anthropometric characteristics, body composition, exposure time to electronic devices or screen time (ST) and physical activity (PA) level along with muscle power and dynamic knee valgus (DKV) in young athletes to avoid future injuries. A total of 125 adolescent basketball athletes (66.4% boys), 12 to 17 years old (13.94±1.58 years) participated. Anthropometric and demographic characteristics were recorded. PA level was assessed through IPAQ and ST through a single question from the HELENA study. The Counter Movement Jump test was used for the evaluation of the lower limb muscle power, while the Single Leg Drop Jump test was used for the evaluation of the dynamic knee valgus via two-dimensional (2D) kinematic analysis. The Pearson index showed a statistically significant positive correlation between muscle power and height (r=0.788, p<0.001), while the Spearman index showed a smaller but equally statistically significant positive correlation with BMI (rs =0.651, p<0.001) and age (rs=0.579, p<0.001). The ST (rs= -0.194, p=0.03) showed a weak negative correlation with DKV, while PA (r=0.85, p<0.001) showed a high, statistically significant, positive correlation. The anthropometric characteristics of adolescent athletes can determine their ability to produce muscle power. A high level of physical activity could play a key role in compensating and thus reducing the negative effects of high exposure to screen time on the dynamic knee valgus

The rehabilitation of the road embankments alongside the irrigation canal, which is constructed on a Bangkok soft clay foundation, has resulted from land use growth for several decades. As a result, the embankment is always confronted with the problem of instability. Numerous articles have demonstrated that rapid drawdown of the water level in the canal could be one of the most significant reasons, whereas vehicle cyclic loading may potentially contribute to some effect of the embankment failure. To explore and assess the effects of the influence factors, the finite element method (FEM) and conventional and dynamic triaxial approaches were employed. The study also investigated the consequences of varying thicknesses of soft clay and cyclic loading with different magnitudes and frequencies. Consequently, cyclic loading can lead to an augmentation in strain distribution and excess pore water pressure. Likewise, more significant deformation and excess pore water pressure were induced by a lower frequency and deeper thickness of soft clay compared to a higher frequency and thinner thickness. In brief, vehicle repetitive loading is one of the primary factors contributing to embankment failure, with the threshold stress being approximately three-fourths of the undrained shear strength. In contrast, threshold strain is approximately one to two-fold of the monotonic strain condition.

Background: Physical and mental health of corporate employees is equally important, especially in international salespeople in the in vitro diagnostic (IVD) medical device industry. The rapid growth of the IVD market is driven by the increasing prevalence of chronic and infectious diseases. This study aims to identify the association of socio-demographic, occupational, organizational, and psychosocial factors with mental health outcomes for depression, anxiety, and somatic symptoms in Chinese IVD international salespeople. Methods: The study was a cross-sectional survey of ISs in IVD companies officially registered in China. An online survey was designed to collect data through email contact with IVD companies and social media between August 2022 and March 2023. Measured factors included effort-reward imbalance (ERI), health-promoting leadership (HPL), health climate (HC), inner strength (IS), and perceived social support (PSS). Mental health outcomes assessed using the Core Symptom Index (CSI) were depression, anxiety, and somatic symptoms. Results: A total of 244 salespeople responded to the survey. CSI scores indicated that 18.4% (n = 45) and 10.2% (n = 25) of the respondents had symptoms of major depression and anxiety, respectively. ERI was positively correlated, while the IS and PSS were negatively correlated with major depression, anxiety, and somatic symptoms (p < .01). Health climate was negatively correlated with major depression (p < .05). Education background was associated with somatic symptoms (p < .05). ERI, IS, and gender were significant predictors of major depression, anxiety, and somatic symptoms (p < .05). Conclusion: The prevalence of depression and anxiety in China’s IVD international salespeople was considered low compared with prevalence in Chinese populations during COVID-19, but higher than those before the pandemic. Effort–reward imbalance, inner strength, and gender were significant factors in major depression, anxiety, and somatic symptoms among IVD international salespeople.

Paving blocks are concrete pieces placed in exposed places to the weather, which are sub-jected to loads and wear. Hence, quality control in the manufacture of paving blocks is es-sential to guarantee the properties and durability of the product in construction projects. In Ecuador, the requirements are described in the Ecuadorian technical standard "NTE INEN 3040", and tensile splitting strength is a fundamental requirement to guarantee product quality. It is analyzed using quality control measurements such as dimensions, the weight of the fresh paving block in the vibro-compacted process, and the percentage of water absorption in order to know how the variables influence and manage to predict the tensile splitting strength to avoid product non-conformity in advance, having a timely and better control of the manufacturing process. The data was obtained from a company that can produce 30 000 units per day of rectangular paving blocks with 6 cm thickness. Mul-tivariate models such as multiple linear regression, regression trees, random forests and neural networks are performed to predict the tensile splitting strength variable through two groups of predictors; the first group is the thickness mm, width mm, length mm, mass of fresh paving block g and percentage of water absorption %. The second group of pre-dictor variables is the density of the fresh paving block kg/m3 and the percentage of water absorption %. It is concluded that the multiple linear regression method performs better in predicting the first group of predictor variables with a mean square error (MSE) of 0.110086, followed by the neural network without hidden layers resulting in an MSE of 0.112198. The best method for the second set of predictors was the neural network with-out hidden layers with a mean square error ( MSE ) of 0.112402, closely followed by the multiple linear regression model with an MSE of 0.115044.

The area of Central and Eastern Europe, and thus Poland, is not exposed to effects of seismic actions. Any possible tremors can be caused by coal or copper mining. Wind, rheological effects, the impact of other objects or a non-uniform substrate are the predominant types of loading included in calculations for stiffening walls. The majority of buildings in Poland, as in most other European countries, are low, medium-high brick buildings. Some traditional materials, like solid brick (>10% of construction materials market) are still used. But autoclaved aerated concrete (AAC) and cement-sand calcium-silicate (Ca-Si) elements with thin joints are prevailing (>70% of the market) on the Polish market. Adding reinforcement only to bed joints in a wall is a satisfactory solution (in addition to confining) for seismic actions occurring in Poland that improves ULS and SLS. This paper presents results from our own tests on testing horizontal shear walls without reinforcement and with different types of reinforcement. This discussion includes 51 walls made of solid brick (CB) reinforced with steel bars and steel trusses, results from tests on 15 walls made of calcium-silicate (Ca-Si) and AAC masonry units reinforced with steel trusses and plastic meshes. Taking into account our own tests and those conducted by other authors, empirical relationships were determined on the basis of more than 90 walls. They are applicable to design and construction phase to determine the likely effect of reinforcement on cracking stress that damage shear deformation and wall stiffness.

Throughout this paper the impact of anxiety on adolescent athlete’s is highlighted through analyzing neurological and psychological aspects involved in sports performance. The neuroanatomy and neuropsychology of the human brain plays a major role in developing athlete’s that has only begun to be analyzed within recent years. Especially in young athletes, there are numerous factors that affect performance on the field that originate from the environment and training the adolescent athlete is involved in. Sports performance is viewed as a major physical factor such as training and lifting weights, however the psychological aspect of sports performance often goes unnoticed. Athletes can begin to develop mental fatigue and anxiety which inevitably can decrease their ability to perform. The athlete’s internal suffering begins to go unnoticed, as the only tangible factor is watching their performance decrease. This causes the athlete to push themselves further in training resulting in greater mental fatigue. This paper emphasizes the numerous factors neurologically that play a role in athletic performance which should be focused on in adolescent athletes as they navigate the challenges and competition that are apparent within athletics. It is critical to understand the processes and hormonal changes the body undergoes with training and playing a sport, this information can change the way adolescent sports are approached and advanced.

The mind-body problem is the central issue in both of philosophy and life science for several centuries. To date, there is still no conclusive theory to interpret the relation between the mind and the body, even just the mind alone. Here, we promote a novel model, a derived mathematic equation called the entropic system equation, to describe the innate characters of the mind and the mechanism of the mind-body coupling phenomenon. As the semi-open thermodynamic systems far from equilibrium, the living organisms could be logically considered as an entropic system. In the living organisms or the entropic systems, there also are three essential existing elements including mass, energy and information, in which the mind and the body are hypothetically coupled by free energy and entropic force.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.