Mechanically strong and thermally stable films obtained from a water-based polyurethane (PU) dispersion with small (0.1–1.5 wt.%) additions of graphene oxide nanosheet (GO) were studied through elemental analysis, X-ray photoelectron spectroscopy, differential thermogravimetry, and Raman spectroscopy. Moreover, the depletion of near-surface layers in nitrogen was presented for all the samples under study. It was found that the introduction of GO into a PU matrix was ac-companied by a partial reduction of graphene oxide nanosheet and an increase in the concentra-tion of defects in its structure.

This study introduces a promising and practical method for the removal of paracetamol from aqueous environments, employing graphene oxide-polymer nanocomposite beads. The approach involves the utilization of a straightforward and facile phase inversion method, offering a convenient and efficient one-step process for the creation of adsorbent beads by integrating polymers and graphene oxide (GO). The synthesized nanocomposite beads are tailored for the removal of paracetamol from simulated wastewater in batch systems. Extensive characterization techniques are employed to scrutinize the chemical properties and structural attributes of the prepared beads. The investigation explores the impact of critical parameters such as adsorbent dosage, adsorption duration, initial paracetamol concentration, and solution pH on the adsorption process. These nanocomposite beads exhibit an exceptional paracetamol removal efficiency, achieving up to 99% removal. This research not only contributes to the advancement of efficient and sustainable adsorbent materials for pollutant removal but also underscores their potential for environmentally friendly and cost-effective solutions in the domain of wastewater treatment.

Graphene is a two-dimensional nanostructured material with intrinsic properties that show promising performance in various applications, including electronics, renewable energy, medicine, mechanical enforcement and others. This study reports a bottom-up approach for the conversion of cyclohexane into graphene nanoflakes, which were then deposited onto fiberglass using a non-thermal generator. The composite was characterized using transmission electron microscopy, which revealed the formation of stacked few-layer graphene with a partially disordered structure and a d-spacing of 0.358 nm between the layers. X-ray diffraction confirmed the observations from the TEM images. SEM images showed the agglomeration of carbonaceous material onto the fiberglass, which experienced some delamination due to the synthesis method. Raman spectroscopy indicated that the obtained graphene exhibited a predominance of defects in its structure. Additionally, Atomic Force Microscopy (AFM) analyses revealed the formation of graphene layers with varying levels of porosity.

Graphene/silicon (Si) heterojunction photodetectors are widely studied in detecting of optical signals from near-infrared to visible light. However, performance of the graphene/Si photodetectors is limited by defects created in the growth process and surface recombination at the interface. Herein, a remote plasma-enhanced chemical vapor deposition is introduced to directly grow graphene nanowalls (GNWs) at a low power, which can effectively improve the growth rate and reduce defects. Moreover, hafnium oxide (HfO2) grown by atomic layer deposition has been employed as an interfacial layer for the GNWs/Si heterojunction photodetector. It is shown that the high-k dielectric layer of HfO₂ acts as an electron blocking and hole transport layer, which minimizes the recombination and reduces dark current. By optimizing the thickness of HfO₂, an extremely low dark current of 3.85×10^(-10) A with a responsivity of 0.19 AW^(-1), as well as a specific detectivity of 1.38×10^12 Jones at zero bias can be obtained for the fabricated GNWs/HfO₂/Si photodetector. This work demonstrates a universal strategy to fabricate high-performance graphene/Si photodetectors.

Graphene nanostructures (GNS) are among the most promising materials for creating supercapacitors. However, GNS are still not used in creating supercapacitors due to the impossibility of obtaining large volumes of high-quality material at an acceptable cost. In this work, we investigated the efficiency of using few-layer graphene (FLG) with the number of layers is not more than 5 synthesized under Self-propagating high-temperature synthesis (SHS) conditions as basic material for supercapacitors. Using the SHS process makes it possible to synthesize large volumes of FLG without Stone-Wales defects. It was found that the synthesized FLG makes it possible to obtain better results than using classical materials, namely activated carbon (AC). It was found that the sample based on FLG has a higher specific capacitance – 65 F×g-1 compared to the sample from AC, the specific capacitance of which is 35 F×g-1, for a speed of 5 mV×s-1 these values are 170 and 64 F×g-1, respectively. The drop in capacitance over 1000 cycles was 4%, which indicates a sufficiently high stability of FLG and allows us to consider FLG as perspective material for use in supercapacitors.

This work is devoted to consideration and analysis of the application of molecular dynamics simulation (MDS) methods to the study of nanosized polymer polyvinylidene fluoride (PVDF) thin ferroelectric films (two-dimensional ferroelectrics) and their composites with graphene layers: 1) to study and calculations of the polarization switching time depending on the electric field and PVDF film thickness; 2) to study and calculations of the polarization switching time depending changes of the PVDF on PVDF-TrFE film; 3) to study the polarization switching time in PVDF under influence of graphene layers. All calculations at each MDS step were carried out using quantum semi-empirical methods PM3. A comparison and analysis of the results of these calculations and the kinetics of polarization switching within the framework of the Landau-Ginzburg-Devonshire theory for homogeneous switching in ferroelectric polymer films is carried out. The study of the composite heterostructures of the “graphene-PVDF” type and calculations of their polarization switching times were presented too. It is shown that replacing PVDF with PVDF-TrFE significantly changes the polarization switching times in these thin polymer films, and that introducing various graphene layers into the PVDF layered structure leads to both an increase and a decrease in the polarization switching time. Here everything also depends on the position and displacement of the ferroelectric coercive field depending on the system damping parameters.

Since the discovery of graphene, due to its excellent optical, thermal, mechanical and electrical properties, it has a broad application prospect in energy, materials, biomedicine, electromagnetism and other fields. A great quantity of researches on the physical mechanism of graphene has been applied to engineering in electromagnetism and optics. To study the properties of graphene, different kinds of numerical methods have been developed for simulating the electromagnetic field effects of graphene, and equivalent boundary conditions have been employed to replace graphene in the computational domain. In this work, the numerical methods with equivalent boundary conditions are reviewed, and some examples are provided to illustrate their applicability.

Optical parametric amplification (OPA) represents a powerful solution to achieve broadband amplification in wavelength ranges beyond the scope of conventional gain media, for generating high-power optical pulses, optical microcombs, entangled photon pairs and a wide range of other applications. Here, we demonstrate optical parametric amplifiers based on silicon nitride (Si₃N₄) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. We achieve precise control over the thickness, length, and position of the GO films using a transfer-free, layer-by-layer coating method combined with accurate window opening in the chip cladding using photolithography. Detailed OPA measurements with a pulsed pump for the fabricated devices with different GO film thicknesses and lengths show a maximum parametric gain of ~24.0 dB, representing a ~12.2 dB improvement relative to the device without GO. We perform a theoretical analysis of the device performance, achieving good agreement with experiment and showing that there is substantial room for further improvement. This work demonstrates a new way of achieving high photonic integrated OPA performance by incorporating 2D materials.

This work is related to the environmental toxicology risk assessment and evaluation of possible transformation of carbon-based nanomaterials (CNMs) after the contact with marine microalgae. The materials used in the study represent common and widely applied multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO). The toxicity was evaluated as growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species generation changes. The measurement was performed with flow cytometry after 3, 24, 96 h, and 7 days. Biotransformation of nanomaterials were evaluated after 7 days of microalgae cultivation with CNMs by FTIR and Raman spectroscopy. The calculated toxic level (EC50 in mg/L, 96 h) of ued CNMs reduced in the following order: CNTs (18.98) > GrO (76.77) > Gr (159.40) > C60 (414.0). Oxidative stress and membrane depolarization was the main toxic action of CNTs and GrO. At the same time, Gr and C60 decreased the toxic action with time and had no negative impact on microalgae even at concentration of 125 mg/L. Moreover, C60 and Gr after seven days of the contact with microalgae cells obtained structural deformations.

Monolayer graphene absorbs 2.3 percent of the incident visible light. This “small” absorption has been used to emphasize the visual transparency of graphene, but it in fact means that multilayer graphene absorbs a sizable fraction of incident light, which causes non-negligible fluorescence. In this paper, we formulate the light emission properties of multilayer graphene composed of tens to hundreds of layers using a transfer matrix method and confirm the method’s validity experimentally. We could quantitatively explain the measured contrasts of multilayer graphene on SiO2/Si substrates and found sizable corrections, which cannot be classified as incoherent light emissions, to the reflectance of visible light. The new component originates from coherent emission caused by absorption at each graphene layer. Multilayer graphene thus functions as a partial coherent light source of various wavelengths, and it may have surface-emitting laser applications.

Traditional graphene-based films normally possess high thermal conductivity (TC) only along single direction, which is not suitable for thermal interface materials (TIMs). Here, a graphene film with excellent bidirectional TC and mechanical properties was prepared by hot-pressing super-elastic graphene aerogel (SEGA). Thermal annealing at 1800℃ improves the further restacking of graphene sheets, bring the SEGA high structure stability for enduring the hot-pressing process. The junctions and nodes between the graphene layers in the hot-pressed SEGA (HPSEGA) film provide bidirectional heat transport paths. The in-plane TC and through-plane TC of HPSEGA film with thickness of 101μm reach 740 Wm-1K-1 and 42.5 Wm-1K-1, respectively. In addition, HPSEGA film with higher thickness still maintains excellent thermal transport properties due to the interconnected structure reducing the effect of the defects. The infrared thermal images visually manifest the excellent thermal-transfer capability and thermal dissipation efficiency of the HPSEGA films, indicating the great potential as advanced bidirectional TIMs.

Graphene-based nanomaterials have emerged as promising materials for a wide range of applications.. Therefore, in the last years carbon nanoparticles have attracted great attention due to their low toxicity, high biocompatibility and easy preparation. Recently, N-doped carbon nanoparticles have been shown to have improved antibacterial activity over the undoped nanomaterial, but it is difficult to find correlations between the structure of the nanoparticle and its antibacterial activity. With this purpose, here, we analyze the effect of both, the nanoparticle size and the surface chemical composition of four N-doped carbon nanoparticles on the growth of Escherichia coli bacteria. Our results were analyzed using a Ligand-Substrate model based on the Monod´s equation, which allows us to interpret the dependence of the nanoparticle-bacteria affinity with the nanomaterial structure.

The growing production and application of carbon-based nanomaterials (CNMs) represent possible risks for aquatic systems. However, the variety of CNMs with different physical and chemical properties, and different morphology complicated the understanding of their potential toxicity. This paper aims to evaluate and compare the toxic impact of four most common CNMs, namely multiwalled carbon nanotubes (CNTs), fullerene (C60), graphene (Gr), and graphene oxide (GrO) in marine microalgae Porphyridium purpureum. The microalgae cells were exposed to the CNMs for 96 h and measured by flow cytometry. Based on the obtained results, we determined no observed effect level (NOEL), calculated EC10 and EC50 concentrations for growth rate inhibition, esterase activity, membrane potential, and reactive oxygen species (ROS) generation changes for each tested CNMs. According to the sensitivity (growth rate inhibition) of P. purpureum, the used CNMs can be listed in following order: CNTs > GrO > Gr > C60. The toxicity of CNTs was significantly higher than the toxic effect of the other used CNMs and only this sample caused increase of ROS generation in microalgae cells. This effect caused by trace metal residuals in CNTs and high affinity between particles and microalgae associated with the presence of exopolysaccharide coverage on P. purpureum cells.

The electronic structure of 7/9-AGNR superlattices with up to eight unit cells has been studied by means of state of the art Density Functional Theory (DFT) and also by two model Hamiltonians, the first one including only local interactions (Hubbard model, Hu) while the second one is extended to allow long-range Coulomb interactions (Pariser, Parr and Pople model, PPP). Both are solved within mean field approximation. At this approximation level, our calculations show that 7/9 interfaces are better described by spin non-polarized solutions than by spin-polarized wavefunctions. Consequently, both Hu and PPP Hamiltonians lead to electronic structures characterized by a gap at the Fermi level that diminishes as the size of the system increases. DFT results show similar trends although a detailed analysis of the density of states around the Fermi level shows quantitative differences with both Hu and PPP models. Before improving model Hamiltonians, we interpret the electronic structure obtained by DFT in terms of bands of topological states: topological states localized at the system edges and extended bulk topological states which interact between them due to the long-range Coulomb terms of Hamiltonian. After careful analysis of the interaction among topological sates, we find that the discrepancy between ab initio and model Hamiltonians can be resolved considering a screened long-range interaction that is implemented adding an exponential cutoff to the interaction term of PPP model. In this way, an adjusted cutoff distance λ = 2 allows a good recovery of DFT results. In view of this, we conclude that the correct description of the density of states around the Fermi level (Dirac point) needs the inclusion of long-range interactions well beyond Hubbard model but not completely unscreened as is the case for the PPP model.

Carbonization of a biopolymer (lignin) in self-propagating high-temperature synthesis (SHS) led to the production of 2D graphene structures. With the help of modern analytical methods (Raman spectroscopy, X-ray diffraction) and electron microscopy, the resulting product was confirmed to have a few-layer 2D graphene structure. The predicted photovoltaic properties of the resulting few-layer graphene were implemented for laser ignition of a model pyrotechnic composition based on porous silicon. A phenomenological model of the formation mechanism of 2D graphene structures under the conditions of the SHS process is proposed.

Graphene-based Field-Effect Transistors (FETs) integrated with microstrip patch antennas offer a promising approach for Terahertz signal radiation. In this study, a dual-stage simulation methodology is employed to comprehensively investigate the device’s performance. The initial stage, executed in MATLAB, delves into charge transport dynamics within a FET under asymmetric boundary conditions, employing hydrodynamic equations for electron transport in the graphene channel. Electromagnetic field interactions are modeled via Finite-Difference Time-Domain (FDTD) techniques. The second stage, conducted in COMSOL Multiphysics, focuses on the microstrip patch antenna’s radiative characteristics. Notably, analysis of the S11 curve reveals minimal reflections at the FET’s resonant frequency of 1.34672 THz, indicating efficient impedance matching. Examination of the radiation pattern demonstrates the antenna’s favorable directional properties. This research underscores the potential of graphene-based FETs for Terahertz applications, offering tunable impedance matching and high radiation efficiency for future Terahertz devices.

The wide application of graphene in the industry requires the direct growth of graphene films on silicon substrates. In this study, we find a possible technique to meet the requirement above. Multilayer graphene thin films (MLG) are grown without a catalyst on Si/SiO2 by pulsed laser deposition (PLD). It was found that the minimum number of laser pulses that are required to produce fully covered (uninterrupted) samples is 500. This number of laser pulses resulted in samples that contain ~5 layers of graphene. The number of layers was not affected by the laser fluence and the sample cooling rate after the deposition. However, the increase of the laser flu-ence from 0.9 J/cm2 to 1.5 J/cm2, results in 2.5 fold reduction of the MLG resistance. The present study reveals that the PLD method is suitable to produce nanocrystalline multilayer graphene with electrical conductivity of the same magnitude as commercial CVD graphene samples.

This study is dedicated to enhancing lithium battery performance through the utilization of porous conductive polyaniline-modified graphene composites (PMGC). Given the growing importance of green energy, coupled with the development of lithium-ion battery systems and electric vehicles, achieving high-speed charge and discharge performance has become imperative. Traditional approaches involve incorporating additives like carbon nanotubes and graphene into electrodes to improve conductivity, but they encounter challenges related to cost and aggregation issues. In this study, polyaniline (PANI), a cost-effective, stable, and conductive polymer, was explored. PMGC was formed by employing ammonium persulfate (APS) as an oxidant during PANI polymerization, simultaneously serving as a surface modifier for graphene. The study systematically investigated the impact of varying amounts of PMGC on lithium-ion battery electrodes, assessing reductions in internal resistance, aging effects, different charge and discharge rates, and cycle performance. PMGC exhibited a porous structure formed by nanoscale PANI intertwining on graphene. Various measurements, including FT-IR, TGA, Raman spectroscopy, and battery performance assessments, confirmed the successful synthesis and positive effects of PMGC. Results indicated that a 0.5% addition of PMGC led to reduced internal resistance and enhanced fast charging and discharge capacity. However, excessive PMGC adversely affected aging and self-discharge. The study provides valuable insights into optimizing PMGC content for improved lithium battery performance, presenting potential advancements in energy storage systems and electric vehicles.

Micro-arc oxidation (MAO) is an emerging technology employed to produce high hardness or anti-corrosion ceramic coatings on lightweight metals such Al, Ti, Mg and their respective alloys. However, under non-lubrication conditions, such coatings exhibit relatively high friction coeffi-cients. To enhance the friction reduction properties of the MAO coatings, we employed a one-step MAO process with varying concentrations of graphene oxide (GO) in an aluminate sys-tem electrolyte to create composite coatings on the surfaces of Ti-6Al-4V alloy. The effect of concentrations of GO particles on microstructure, composition, and wear behavior of the result-ing composite coatings was investigated. Measurements of the coating's thickness, hardness, and roughness have also been conducted. Ball-on-disk friction test under dry condition were carried out to reveal tribological behavior of the MAO coating. The addition of graphene oxide in the electrolyte reduces the friction coefficient, with the composite coating containing 5 g/L of GO particles displaying the most effective friction reduction. Moreover, coating thickness increases with higher GO concentration. This friction reduction can be attributed to the particles in the coating acting as lubricants during friction, while GO also reduces adhesive damage, shifting the wear mechanism from adhesive to abrasive.

Wastewater treatment from oils and oil products, organic mixtures are a very relevant topic that can be successfully used to solve problems of serious environmental pollution, such as oil spills, industrial oily wastewater discharges and water treatment in the water treatment process. In this work, we have developed new superhydrophobic magnetic polyurethane (PU) sponges functionalized with reduced graphene oxide (RGO), MgFe2O4 nanoparticles, and silicone oil (SO) as a selective and reusable sorbent for purification and separation of wastewater from oils and organic solvents. The surface morphology and wettability of the sponge surface were characterized by scanning electron microscopy (SEM) and a contact angle analysis system, respectively. The results showed that the obtained PU sponge PU/RGO/MgFe2O4/SO had excellent mechanical and water-repellent properties, reusable properties (more than 20 cycles), as well as fast (immersion time 20 sec) and excellent adsorption capacity (16.61- 44.86 g / g), and good magnetic properties made it easy to separate the sponge from the water with a magnet. And the presence of RGO in the composition of the nanomaterial improves the separating and cleaning properties of materials, and also leads to an increase in the absorption capacity of oil and various organic solvents. The synthesized PU sponge has great potential for practical applications due to its facile fabrication and excellent oil-water separation property.

This work deals with the analysis of phase composition of sintered Ti-Al-C composite materials under high voltage electrical discharge. The samples of Ti-Al-C powder composites were tested by SEM, Raman spectroscopy and XRD. It was determined that the treatment of the powder by high voltage electrical discharge (HVED) and further sintering at high temperatures using the method of spark plasma sintering (SPS) encourages the formation of the intermetallic reinforcing phases, carbides and different nanocarbon structures like graphene and fullerenes, as well as pure graphite. Intermetallic phases and nanocarbon structures improve mechanical and physical properties of the composites. By using experimental methods mentioned above, the phase composition of Ti-Al-C powder composites obtained at different sintering temperatures was determined.

The poor conductivity and instability of layered dihydroxides (LDHs) limit their widespread application in oxygen evolution reaction (OER). In this study, the composite electrode of NiMn-LDHs, reduced graphene oxide (rGO) and nickel foam (NF), i.e., NiMn-LDHs/rGO/NF, was prepared by a hydrothermal method. When subjected to oxygen evolution reaction (OER) catalytic performance in a solution of 1 M KOH, the NiMn-LDHs/rGO/NF composite catalyst exhibited an overpotential of only 140 mV at a current density of 10 mA cm-2 and a Tafel slope of 49 mV dec-1, which is not only better than the comparing RuO2/NF catalyst, but also better than most of the Mn-based and the Ni–Fe containing bimetallic OER catalysts reported in the literature. The excellent electrocatalytic performance is ascribed to the efficient integration of ultrathin NiMn-LDHs sheets, thin-layered rGO and NF, contributing a lot to the decrease in charge transfer resistance and the increase in electrochemically active surface area. Moreover, NF plays a role of current collector and a role of rigid support for the NiMn-LDHs/rGO composite, contributing extra conductivity and stability to the NiMn-LDHs/rGO/NF composite electrode.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

Pastes containing reduced graphene oxide (rGO) and LiCl-Mn(NO3)2·4H2O are screen-printed on a carbon cloth substrate and then calcined using a nitrogen atmospheric-pressure-plasma jet (APPJ) for conversion into rGO-LiMnOx nanocomposites. The APPJ processing time is within 300 s. RGO-LiMnOx on carbon cloth is used to sandwich H2SO4, LiCl, or Li2SO4 gel electrolytes to form hybrid supercapacitors (HSCs). The areal capacitance, energy density, and cycling stability of the HSCs are evaluated using electrochemical measurement. The Li2SO4 gel electrolyte HSC exhibits the highest areal capacitance and energy density but lower cycling stability. By contrast, the H2SO4 gel electrolyte HSC exhibits better cycling stability but lower areal capacitance and energy density.

Graphene is perhaps the most prominent “Dirac material,” a class of systems whose electronic structure gives rise to charge carriers that behave as relativistic fermions. In multilayer graphene several crystal sheets are stacked such that the honeycomb lattice of each layer is displaced along one of the lattice edges. When subject to an external magnetic field, the scaling of the multilayer energy spectrum with the magnetic field, and thus the system’s thermodynamic behavior, depends strongly on the number of layers. With this in mind, we examine the performance of a finite-time endoreversible Otto cycle with multilayer graphene as its working medium. We show that there exists a simple relationship between the engine efficiency and the number of layers, and that the efficiency at maximum power can exceed that of a classical endoreversible Otto cycle.

Matter grows and self-assembles to produce complex structures such as virus capsids, carbon fullerenes, proteins, glasses, etc. Due to its complexity, performing pen-and-paper calculations to explain and describe such assemblies is cumbersome. Many years ago, Richard Kerner presented a pen-and-paper path integral approach to understand self-organized matter. Although successfully addressed many important problems including the yield of fullerene formation, the glass transition temperature of doped chalcogenide glasses, the fraction of boroxol rings in B2O3 glasses, the first theoretical explanation for the empirical recipe of window and Pyrex glass and the understanding of virus capsid self-assembly, still is not the primary choice when tackling similar problems. The reason lies in the fact that it diverges from mainstream approaches based on the energy landscape paradigm and non-equilibrium thermodynamics. In this context, a critical review is presented, demonstrating that the Richard Kerner method is, in fact, a clever way to identify relevant configurations. Its equations are simplified, common physical sense versions to those found in the energy landscape kinetic equations. Subsequently, the utilization of equilibrium Boltzmann factors in the transition Markov chain probabilities is analyzed within the context of local two-level energy landscape models kinetics. This analysis demonstrates that their use remains valid when the local energy barrier between reaction coordinate states is small compared to the thermal energy. This finding places the Richard Kerner model on par with other more sophisticated methods and, hopefully, will promote its adoption as an initial and useful choice for describing the self-agglomeration of matter.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

In the work the enhanced security of unmanned aerial vehicles (UAVs) electronics in RF environment was investigated. UAVs are commonly used in many areas and the cellular networks as the parallel helping networks for systems: LTE, 5G or especially for future 6G are very perspective and needed. For effective communications in channels: “air-to-ground” as well as “drone-to-drone” the important task is undisturbed work of transportation platforms, ie. UAV. However, high level of outside electromagnetic radiation can affect the correct electronics work. The problem is due to non-conformity of RF environment regulations. The electromagnetic compatibility (EMC) standards guarantee correct electronics work when the radiation level is not higher than established EMC levels. In case of commercially available devices, like UAVs, this level is 3 V/m. On the other hand, permissive exposure level, treated as RF environment emitted by cellular base stations, can reach the level of 61 V/m. Such level of electromagnetic wave pollution, can damage unprotected electronics with fatal consequences. This can cause the unchecked drone flight or unchecked fall down. As a result, due to unchecked flight, the UAV can cause the sudden communication interruption with operator or other drones. To reduce the level of damaging RF field we propose to cover the UAV housing with microwave absorber. In this case absorber must ensure good electromagnetic protection as well as lightweight and resistant on weather conditions. The shielding property of reduced graphene oxide (RGO) as an absorber was investigated. For proposed material the shielding effectiveness (SE) was investigated in the frequency range from 100 MHz to 10 GHz. It has been proved that such material can be a good candidate as an absorber for UAV having low reflection coefficient and high absorption ability. In this work the shielding effectiveness of RGO was analyzed for two layers of 3 and 5 mm at typical frequencies as RF environment, ie. 3.6 GHz (5G system) and 5.8 GHz (LTE). Investigated absorber guarantees the value of SE of 25 dB and 30 dB for 3 mm layer at 3.6 GHz and 5.8 GHz respectively and of 29 dB and 39.5 dB for 5 mm layer at these frequencies respectively.

Graphene hybrid-filler polymer composites have emerged as prominent materials that revolutionize heavy industries. This study encapsulates the in-depth analysis of different influential factors such as filler/graphene type, aspect ratios, dispersion methods, filler-matrix compatibility, fiber orientation, synergistic effects, different processing techniques, and post-curing conditions that affect the processing, properties and determine the resultant applications of graphene hybrid polymer composites. Additionally, it discusses the substantial role of graphene collaboration with other fillers such as carbon nanotubes, silica, nano-clays and metal oxides to produce functionalized hybrid polymer composites with synergistically enhanced tailored properties to offer solutions for heavy industries like aerospace, automotive, electronics, and energy harvesting. The review concludes with some suggestions and outlook on the future of these composite materials by emphasizing the need for continued research to fully optimize their potential.

This study introduces a low-cost solution provided by a specialized source measure unit (SMU), offering an alternative to conventional source meter units. Through precise IV curve measurements for graphene-channel FETs, the SMU demonstrates its capability in accurately characterizing these devices with minimal noise and high accuracy. This cost-effective solution presents a promising avenue for researchers and developers seeking reliable tools for sensor development and characterization, providing valuable insights into the behavior of graphene-channel FETs and the effect of surface illumination without the need for expensive equipment. Additionally, the SMU was validated with known passive and active components, along with probe station integration for microscale connection, ensuring its effectiveness in capturing accurate measurements. The SMU’s focus on collecting IV curves, coupled with its ability to identify device defects, such as Schottky junctions, contributes to its utility in quality testing for semiconductor devices. Its low-cost nature makes it accessible for various research endeavors, enabling efficient data collection and analysis for graphene-based sensor applications.

Temperature-responsive separation membranes can significantly change their permeability and separation properties in response to changes in their surrounding temperature, improving efficiency and reducing membrane costs. This study focuses on the modification of commercial polyvinylidene fluoride (PVDF) membranes with amphiphilic temperature-responsive copolymer and inorganic nanoparticles. We prepared an amphiphilic temperature-responsive copolymer which the hydrophilic poly(N-isopropyl acrylamide) (PNIPAAm) was side-linked to a hydrophobic polyvinylidene fluoride (PVDF) skeleton. Subsequently, PVDF-g-NIPAAm polymer and graphene oxide (GO) blended with PVDF to prepare temperature-responsive separation membranes. The results showed that temperature-responsive polymers with different NIPAAm grafting ratios were successfully prepared by adjusting the material ratio of PVDF to NIPAAm. PVDF-g-NIPAAm was blended with PVDF with different grafting ratios to obtain separate membranes with different temperature responses. GO and PVDF-g-NIPAAm formed a relatively stable hydrogen bond network, which improved the internal structure and mechanical properties of the membrane without affecting the temperature response, thus extending the service life of the membrane.

To improve the wear resistance of polyimide (PI), surface modification was developed. In this study, the tribological properties of graphene (GN), graphene oxide (GO), and KH550-grafted graphene oxide (K5-GO) modified PI were evaluated by molecular dynamics (MD) at the atomic level. The findings indicated that the addition of nanomaterials can significantly enhance the friction performance of PI. The friction coefficient of PI composites decreased from 0.253 to 0.232, 0.136, and 0.079 after coating GN, GO and K5-GO, respectively. Among them, the K5-GO/PI exhibited the best surface wear resistance. Importantly, the mechanism behind the modification of PI was thoroughly revealed by observing the wear state, analyzing the changes of interfacial interactions, interfacial temperature, and relative concentration.

In this study, a composite film was developed for electrochemical sensing of tryptophan (Trp). Porous reduced graphene oxide (PrGO) was utilized as the electron transfer layer, and a C-undecylcalix[4] resorcinarene Langmuir-Blodgett (CUCR-LB) film served as the molecular recognition layer. Atomic force microscopy (AFM), transmission electron microscopy (TEM), Raman spectroscopy, scanning electron microscopy (SEM), and electrochemical experiments were employed to analyze the characteristics of the CUCR-LB/PrGO composite film. The electrochemical behavior of Trp on the CUCR-LB/PrGO composite film was investigated, revealing a linear response range of Trp was 1.0×10-7 to 3.0×10-5 mol L-1 and a detection limit of 3.0×10-8 mol L-1. Furthermore, the developed electroanalytical method successfully determined Trp content in an amino acid injection samples. This study not only introduces a rapid and reliable electrochemical method for determination of Trp but also presents a new strategy for constructing high-performance electrochemical sensing platforms.

The band gap research in graphene is still a very important topic for materials application. Here, we report a band gap opening and p-type semiconducting property of the graphene by using an electrochemical doping on graphene surface. The manganese-oxide nanopar-ticles adsorbed on the graphene were used as the dopants in an electrolyte, which induce the band gap opening and the change of electronic structure. In addition, the fabricated graphene FET shows the p-type semiconductor behaviors. The temperature dependent conductivity of the p-type doped graphene at applied potential of 1.5 V during electro-chemical doping shows the formation of band gap of 0.23 eV, which is obtained from the fitting of conductivity equation. The semiconducting properties of manganese-oxide doped graphene is attributed to the formation of manganese-oxide nanoparticle on the surface of graphene.

Alcoholic liver disease (ALD) develops when the immunotolerant environment of the liver is compromised due to excessive alcohol consumption. ALD progression involves variations in the expression of multiple genes, resulting in liver inflammation and the development of a leaky gut. Molecular mechanism involved for ALD progression is still unclear, and due to that there are currently no FDA-approved drugs available for its treatment. In this study, the protective effects of Graphene oxide nanoparticles (GO) was investigated against ethanol-induced damage in the gut-liver axis in in vitro. GO was synthesized using a modified Hummer's method and characterization was done. Given the general concerns regarding nanoparticle toxicity, assessment of cell viability, lipid accumulation, DNA damage, cell death, and the generation of reactive oxygen species (ROS) were conducted using various techniques. Furthermore, gene expression of pro- and anti-inflammatory cytokines was done using RT-qPCR. The findings revealed that GOs promoted cell viability even against ethanol treatment. Additionally, lipid accumulation significantly decreased when cells were treated with GO alongside ethanol compared to ethanol treatment alone, with similar trends observed for other assays. Gene expression analysis indicated that GO treatment reduced the expression of proinflammatory cytokines while enhancing the expression of antioxidant genes. Moreover, GO treatment led to improvements in gut permeability and a reduction in proinflammatory cytokines in colon cells damaged by ethanol. These findings suggest that GO holds promise as a drug carrier, exhibiting no observed toxic effects. By shedding light on the protective effects of GO against ethanol-induced damage, this study contributes to the burgeoning field of nanoparticle-mediated therapy for ALD.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with redox graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorporation of rGO would increase the interlayer spacing of NVO and diminish the charge transfer interactions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 94.54% of its initial specific capacity of 506.9 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

Graphene, a single layer of carbon atoms arranged in a two-dimensional honeycomb lattice, has attracted tremendous attention due to its exceptional properties and diverse applications. Synthesis methods play a crucial role in tailoring graphene's properties for specific applications. This review provides a comprehensive overview of recent advances in graphene synthesis techniques, including chemical vapor deposition (CVD), exfoliation, epitaxial growth, and chemical reduction. We discuss the principles, advantages, challenges, and applications associated with each method. Furthermore, emerging trends and future prospects in graphene synthesis are explored, with a focus on scalability, cost-effectiveness, and environmental sustainability.

Highly-doped graphene samples show the conductance reduced and the shot-noise power enhanced compared to standard ballistic systems in two-dimensional electron gas. These features can be understood within a model assuming incoherent scattering of Dirac electrons between two interfaces separating the sample and the leads. Here we find, by adopting the above-mentioned model for the edge-free (Corbino) geometry and by means of the computer simulation of quantum transport, that another graphene-specific feature should be observable when the current flow through a doped disk is blocked by high magnetic field. In case the conductance drops to zero, the Fano factor approaches the value of $F\approx{}0.56$, with a very weak dependence on the disk radii ratio. The role of finite source-drain voltages and the system behavior upon tuning the electrostatic potential barrier from a rectangular to parabolic shape are also discussed.

Graphene oxide (GO) is considered as one of the promising adsorbents for the removal of various heavy metal contaminants in aquatic environment, due to its beneficial structural, chemical and electronic properties. Using the density functional theory (DFT) approach, we investigate the reactivity of a model GO nanoparticule (C30H14O15) toward neutral and charged lead (Pb) and cadmium (Cd) atoms. We found the model metal-free GO to have a high chemical reactivity. To study the adsorption of the metal atoms on the GO nanoparticle, we have used a single and doubly-adsorbed neutral (Pb0 and Cd0) and charged (Pb2+, Cd2+) atoms. After identified possible adsorption sites on the GO, we found that a single charged metal ion binds more strongly than a neutral atom of the same type. To determine the possibility of multiple adsorptions of GO nanoparticle, two metal atoms of the same species are co-adsorbed on its surface. Our calculations reveals a site-dependent adsorption energy such that when two atoms of the same specie are adsorbed at sites Si and Sj , the binding energy per atom depends on the whether one of the two atoms is adsorbed firstly on the Si or Sj sites. It is also found that the binding energy per atom for two co-adsorbed atoms of the same specie is less than the binding energy of a singly-adsorbed atom which suggests that atoms may become less likely to be adsorbed on the GO nanoparticle when their concentrations increase. This applies to both neutral and charged atoms. We adduce the origin of this observation to be interplay between metal-metal interaction on the one hand and GO-metal on the other, with the former resulting in a less binding for the charged adsorbed metals in particular, due to repulsive interaction between two positively charged ions. The frontier molecular orbitals analysis and the calculated global reactivity descriptors of the respective GO- metal complexes revealed that all the GO-metal complexes have a smaller HOMO-LUMO gap (HLG) relative to that of pristine metal-free GO nanoparticle. This suggests that although the GO-metal complexes are stable, they are less stable compared to metal-free GO nanoparticles. The negative values of the chemical potentials obtained for all the GO-metal complexes further confirms their stability. Our work calculates parameters that will be crucial to rational design of GO nanoparticles for Pb abd Cd ions contaminants removal, and may find application in water purification for example.

Graphene quantum dots (GQDs) have garnered significant attention in recent years due to their unique properties and promising applications in various fields such as electronics, optoelectronics, bioimaging, and sensing. The synthesis of GQDs is a critical step in harnessing their potential, and numerous methods have been developed to produce GQDs with specific properties. This review provides an overview of the different techniques employed for synthesizing GQDs, including top-down and bottom-up approaches. Furthermore, it discusses the advantages, limitations, and potential applications of each method, offering insights into the future direction of GQD synthesis research.