This paper presents a new implementation of a 2-box absolute flow model, enabling the calculation of CO₂ transfer between the atmosphere and a mixing reservoir representing the combined effect of the terrestrial and ocean regions. The model uses published values of anthropogenic CO₂ fossil fuel emissions (CO2ff), atmospheric CO₂ mixing ratio and nuclear weapons bomb yields, to compute atmospheric d¹³C and Δ¹⁴C time-series. The level of agreement between the calculated values and the accepted values for d¹³C is within ± 0.05 ‰, and for Δ¹⁴C is within ± 3‰, spanning 200 years. The model contains only seven internal parameters; these are varied to optimize the fit, leading to reasonable parameter values, indicating the validity of the method. In addition, the model shows how a rising CO₂ exchange influx fluctuating with surface temperature is compatible with a nett atmospheric CO₂ sink. The study demonstrates that a single CO₂ residence time applies to both the ¹⁴C bomb pulse and the anthropogenic flux, contrary to the conventional view that "bomb radiocarbon and anthropogenic CO₂ do not behave identically." [Joos 1994 Nature 370, 181–182]. It is shown that the difference in behaviour, claimed to be due to seawater chemistry, is not significant in practice since fluctuating bulk carbon dominates fluctuating isotopic ratio. A new analysis of the airborne fraction indicates that the assumption of a time-dependent exchange influx results in a similar residence time for bulk CO₂ as for ¹⁴C in the nuclear bomb pulse, reinforcing the view that the ¹²C, ¹³C and ¹⁴C carbon isotopic forms of CO₂ behave similarly in the carbon cycle.

Rising fuel costs, significant air pollution, and the need to mitigate the negative consequences of oil consumption have diminished the relevance of traditional vehicles. This shift encourages the adoption of safer, more efficient, and eco-friendly transportation alternatives, such as fuel cell, electric, and hybrid vehicles. Brushless direct current motors are gaining popularity due to their high efficiency, power factor, torque, and controllability. By 2030, Brushless Direct Current motors are expected to replace conventional motors as the standard for power transfer, especially in dynamic applications like automobiles, more electric aircraft. This study explores a control technique to improve real-time control of brushless direct current motors in electric vehicles It presents speed control of these system for electric vehicle applications and an overview of electric vehicle technologies. A model for the 120-degree mode was developed using electrical and mechanical equations in MATLAB/Simulink. Three scenarios were examined to assess the potential of controlling brushless direct current motors using constant and dynamic speed and torque. The actual value reached the reference value in the first two scenarios.

Background: Inadequate meibomian glands (MGs) secretion can lead to dry eye signs and symptoms. Tear film lipid layer (TFLL) secreted by MGs protects and prevents rapid evaporation of tear film. Our purpose was to assess TFLL alteration and function in patients with evaporative dry eye (EDE) using tear interferometry after optimal pulse light technology (OPT) intense pulsed light (IPL). Methods: This prospective randomized examiner-masked sham- controlled study included 86 participants (142 eyes) with DED. IPL or sham procedure was performed on day 0, 21, and 42. Ocular Surface Disease Index (OSDI), non-invasive breakup time (NITBUT), interferometric fringe pattern determined TFLL quality, fluorescein staining (FS), and meibum gland (MG) were assessed at day 0, 21, 42 and 3-month. Results: At 3-month, TFLL, NITBUT, MG drop-out, MG quality, MG expressibility, FS and OSDI improved significantly (P<0.05) in the IPL group, while the sham group had no significant improvements. All DE parameters significantly correlated with the improvement in TFLL following IPL treatment. Additionally, artificial tears usage was significantly less in the IPL group from D-42 onwards. Conclusion: IPL treatment demonstrated the ability to improve TFLL quality and clinically reduced sign and symptoms of DED thereby reducing the frequency of artificial tears usage.

This work investigates the use of Non-destructive tests as a tool for monitoring the structural performance of concrete structures. The investigation encompassed four phases; the first of which involved the use of destructive and non-destructive mechanisms to assess concrete strength on cube specimens. The second phase research focused on site assessment for a twin engineering theatre located at the Faculty of Engineering, University of Lagos using rebound hammer and ultrasonic pulse velocity tester. The third phase was the use of linear regression analysis model with MATLAB to establish a relationship between calibrated strength as well as ultrasonic pulse velocities with their corresponding compressive strength values on cubes and values obtained from existing structures. Results show that the root-mean squared-R² values for rebound hammer ranged between 0.275 and 0.742 while ultrasonic pulse velocity R² values were in the range of 0.649 and 0.952 for air curing and water curing systems respectively. It initially appeared that the Ultrasonic pulse velocity was more suitable for predicting concrete strength than rebound hammer but further investigations showed that the latter was adequate for early age concrete while the former was more suited for aging concrete. Hence, a combined use is recommended in this work.

Sepsis still remains one of the most difficult conditions to diagnose as it presents unspecific clinical signs and symptoms, which makes early detection crucial. Our study aimed to enhance the accuracy of sepsis diagnosis by integrating multimodal monitoring technologies with traditional diagnostic methods. The research involved 121 newborns, comprising 39 cases of late-onset sepsis, 35 cases of early-onset sepsis, and 47 control subjects. Biosignals including pulse oximetry (PO), near-infrared spectroscopy (NIRS), and skin temperature (ST) were continuously monitored and an algorithm was developed using Python for identifying early signs of sepsis. The model demonstrated the ability to detect sepsis 6 to 48 hours in advance with an accuracy rate of 87.67% ± 7.42%. Sensitivity and specificity were recorded at 76% and 90%, respectively, with NIRS and ST having the most significant impact on predictive accuracy. Despite the promising results, limitations such as sample size, data variability, and potential biases were noted. The findings highlight the critical role of non-invasive biosensing methods in conjunction with traditional biomarkers and cultures, offering a robust framework for early sepsis detection and improved neonatal care. Further studies are recommended to validate these results across diverse clinical settings.

Photonic integrated circuits (PIC) devices are impacted by fabrication tolerances and therefore, prior knowledge of such variation could improve the PIC fabrication process and overall yield. This paper presents a method for predicting the fabrication impacts on a telecommunication optical digital to analog converter (oDAC) based pulse amplitude modulator level four (PAM-4) transmitter. Our findings allow us to estimate the production yield in fabrication scenario using symbol error rate (SER) benchmark.

In the permanent magnet synchronous motor (PMSM) drive system, the unwilling and ear-piercing vibro-acoustics caused by high-frequency sideband harmonics becomes unacceptable in the electric vehicle application. In this paper, a modified space vector pulse-width modulation (SVPWM) technique implemented with hybrid carrier frequency modulation (HCFM) is provided to reduce the sideband current harmonic components and vibro-acoustic responses. The principle and implementation of the proposed HCFM technique are firstly presented, in which the fixed carrier frequency is improved with the sawtooth and random signal-based coupling modulation based on the rotor position. For verification, the experiment tests are carried out on a prototype 12/10 PMSM and microcontroller unit. The effectiveness of the HCFM technique can hence be confirmed, in which the sideband vibro-acoustics reduction shows more effectively than that in conventional random PWM. The proposed approach may provide a new route in noise-cancelling and electromagnetic compatibility for the electric drive powertrain.

The screen-printed carbon nanofibers electrodes (SPCNFE) represent an alternative with great acceptance due to their results, as well as their low impact for the environment. In order to improve their performance, in the present work they were modified with silver nanoparticles (Ag-NPs) and electrochemically characterized by using anodic stripping voltammetry. From the Ag-NPs synthesis, silver seeds (Ag-NS) and silver nanoprisms (Ag-NPr) were obtained. The Ag-NPs formation was confirmed by micrographs where Ag-NPs with diameters of 12.20±0.04 nm for Ag-NS, and 20.40±0.09 nm for Ag-NPr were observed. The electrodes were modified by using three different deposition methods: drop-casting, spin-coating and in-situ approaches. It was observed that the last methodology showed a low amount of Ag-NS deposited on the electrode surface and a deep alteration of this surface. Those facts suggested that the in situ synthesis methodology were not appropriate for the determination of heavy metals and it was discarded. The incorporation of the nanoparticles by spin-coating and drop-casting strategies showed different spatial distribution on the electrode surface as proved by scanning electron microscopy. The electrodes modified by these strategies, were evaluated for the cadmium(II) and lead(II) detection using differential pulse anodic stripping voltammetry, obtaining detection limit values of 2.1 and 2.8 µg L^-1, respectively. The overall results showed that the incorporation route does not change directly the electrocatalytic effect of the nanoparticles, but the shape of these nanoparticles (spherical for seeds and triangular for prisms) has a preferential electrocatalytical enhancement over Cd(II) or Pb(II).

Wide bandgap (WBG) power semiconductor devices are increasingly replacing silicon IGBTs in high-power and high-voltage power electronics applications. However, there is a significant gap in the literature regarding efficient testing methodologies for high-power and high-voltage converters under constrained laboratory resources. This paper addresses this gap by presenting comprehensive, hardware-focused testing methodologies for high-power and high-voltage WBG power semiconductor based converters, preceding the control evaluation phase. The proposed methods enable thorough evaluation and evaluation of converter hardware, including device switching characteristics, driving circuit functionality, thermal management performance, insulation integrity, and sustained operation at full power. We utilize the double pulse test (DPT) to characterize switching performance in a two-level phase leg configuration, extract circuit parasitics, and validate magnetic components. The DPT is further applied to optimize gate driving circuits, validate overcurrent protection mechanisms, and measure device on-resistance. Additionally, a multicycle test is introduced to rapidly assess steady-state converter performance and estimate efficiency. Recognizing the critical role of thermal management in high-power converters, our methodologies extend to the experimental extraction of key thermal parameters—such as junction-to-ambient thermal resistance and thermal capacitance—via a heat loss injection method. A correlation method between temperature sensor measurements and junction temperature is presented to enhance the accuracy of device temperature monitoring during tests. To ensure reliability and safety, dielectric withstand tests and partial discharge measurements are conducted at both component and converter levels under conventional 60 Hz sinusoidal and high-frequency PWM waveforms. Finally, we highlight the importance of testing converters under full voltage, current, and thermal conditions through power circulating tests with minimal power consumption, applicable to both non-isolated and isolated high-power converters. Practical examples are provided to demonstrate the effectiveness and applicability of these hardware testing methodologies.

Casein hydrolysate improves arterial stiffness, as estimated by brachial ankle pulse wave velocity (baPWV), in untreated hypertensive subjects. Facial pigmentation is a useful biomarker for arterial stiffness. This trial evaluated whether casein hydrolysate improves facial pigmentation in association with changes in arterial stiffness. A randomized, double-blind, placebo-controlled trial was conducted in 80 non-hypertensive Japanese participants randomly assigned to receive either active tablets containing casein hydrolysate or placebo for 48 weeks. Facial pigmentation and baPWV were measured at baseline and at the end of the intervention. Other biochemical atherosclerosis-related parameters were also measured, including advanced glycation end products (AGEs). Changes in facial pigmentation showed a significant difference between the groups. Change in baPWV was significantly better in the active than in the placebo group. In contrast, no significant association was seen between changes in facial pigmentation and those in baPWV. Among other atherosclerosis-related factors, changes in advanced glycation products (AGEs) were significantly decreased in the active compared to the placebo group. Further, changes in facial pigmentation were positively correlated with those in AGEs. Changes in AGEs were independently associated with changes in facial pigmentation. Casein hydrolysate improves facial pigmentation in non-hypertensive participants. Casein hydrolysate may have beneficial effects on glycation stress.

Since the beginning of the 21th century, infrared Nd:YVO4 pulsed lasers have been widely applied especially in some actual industrial processes. In the working process of a laser-aided etching device, the “match-head” effect must be effectively controlled by suppressing the first giant pulse for a solid-state Q-switched laser. In the process of optimizing the infrared Nd:YVO4 pulsed laser by adjusting the slope parameters of the radio frequency (RF) modulation to suppress the first giant pulse, it has been come across that some abnormal horizontally polarized emission with a very short time appears before the formal vertically polarized emission when the gate signal is artificially started. Actually, abnormal horizontally polarized emission will bring some unexpected machining traces during the production process and even greater dangers. The experimental results show that with the increase of the slope duration of a RF signal, the existence time of abnormal output horizontal polarized light will be shortened, and the horizontal giant pulse and vertical giant pulse are well suppressed. When the slope duration is greater than 0.18 ms both horizontal and vertical giant pulses will disappear. The horizontal polarized light can be thoroughly suppressed when the slope duration is greater than 13.7 ms. Compared with the method of adding polarizer to eliminate abnormal output horizontal polarized light, this method does not add elements in the laser, ensuring that the laser volume is relatively small, and does not affect the quality of the normal output laser. The research conclusion is thought to be of great practical significance especially for processing transparent materials.

In this work, we studied light-output properties, efficiency function as well as PSD capability of p-Terphenyl scintillator. The selected solid cylindrical scintillation detector has a size of (45 x 45) mm with PSD properties. Recently presented studies of light-output functions have been meas-ured only for low neutron energies. Our motivation has been to determine more accurate the light output function for p-Terphenyl scintillator over a wider neutron energy range. The measurements have been carried out with mono-energetic neutron beams in the wide energy range from 2.5 to 19 MeV. The neutron-gamma spectrometric system, which we developed has been used for the measurement. The input analogue signal from the detector is digitized with fast 12-bits analogue to digital converter with sampling frequency of 1 GHz. Measured data from the detector are processed into gamma and neutron spectra. The light output function for protons has been determined by finding the position of the protons for given neutron energies. The more accurate light output function for p-Therphenyl scintillator has been calculated. The pulse-shape discrimination capability as well as efficiency of p-Terphenyl scintillator in comparison with NE-213 equivalent detector is lower.

In this paper, we study the effect of decreasing aperture diameter on signal transmission from the scintillator to the PMT. The apertures have been inserted directly between the scintillator and the photomultiplier. Three different aperture diameters have been used over a wide energy range.A newly developed fast digital spectrometer has been utilised for experimental measurement in the radial channel of the VR-1 research reactor. The detector signals with and without inserted apertures have been measured and evaluated. The aim of our research was to determine the effect of the apertures on the spectral quality, energy range and the evaluated physical quantities.

The article presents an induction generator connected to the power grid using the AC / DC / AC converter and LCL coupling filter. In the converter, both from the generator side and from the power grid side, three-level inverters were used. The algorithm realizing Pulse Width Modulation (PWM) in inverters has been simplified to the maximum. Control of the induction generator was based on the Direct Field Oriented Control (DFOC) method. At the same time, voltage control has been used for this solution. The MPPT algorithm has been extended to include the variable pitch range of the wind turbine blades. The active voltage balancing circuit has been used in the inverter DC voltage circuit. In the control system of the grid converter with an LCL filter, the number of measurements was limited to the measurement of power grid currents and voltages. Synchronization of control from the power grid side is ensured by the use of a PLL loop with the system of preliminary suppression of undesired harmonics (CDSC).

The paper explores the features of numerical simulation to analyze the dynamic behavior of drives controlled by pulse-width modulators. Modern motor control systems widely use pulse width modulation. Effective numerical modeling of such systems has specific features because the models employed are continuous-event and have hybrid behavior due to the presence of nonlinear links with discontinuities of the first kind. Therefore, it is essential to have special integration methods with variable steps, which should be factored in when developing the model. The paper shows how these problems are solved when modeling an electric drive with a DC motor in the SimInTech software.

Spin-orbit coupling and nonparaxiality effects during propagation of vortex vector light beams in a cylindrical graded-index waveguide are investigated by solving the full three-component field Maxwell’s equations. Symmetry breaking effects for left- and right-handed circularly polarized vortex light beams propagating in a rotationally symmetric graded-index optical fiber are considered. The mode-group delay in a graded-index fiber due to spin-orbit interaction is demonstrated. It is shown that the relative delay times between vortex pulses of opposite circular polarizations of the order of 10 ps/km can be observed in graded-index fibers for high-order topological charges.

Electrophysiological mapping (EM) using acute electrode probes is a common procedure performed during functional neurosurgery. Due to their constructive specificities, the EM probes are lagging in innovative enhancements. This work addressed complementing a clinically employed EM probe with carbonic and circumferentially segmented macrocontacts that are operable both for neurophysiological sensing ("recording") of local field potentials (LFP), and for test stimulation. The paper illustrates in-depth the development, that is based on direct writing of functional materials. The unconventional fabrication processes were optimized on planar geometry and then transferred to the cylindrically thin probe body. We report and discuss on the constructive concept and architecture of the probe, characteristics of the electrochemical interface deduced from voltammetry and chronopotentiometry, and the results of in vitro and in vivo recording and pulse stimulation tests. Two and three directional macrocontacts were added on probes having shanks of 550 and 770 m diameters and 10-23 cm lengths. The graphitic material presents a ~2.7 V-wide, almost symmetric water electrolysis window, and an ultra-capacitive charge transfer. When tested with 150 s biphasic current pulses, the interfacial polarization stayed safely away from the water window for pulse amplitudes up to 9 mA (135 C/cm2). The in vivo experiments on adult rat models confirmed the high-quality sensing of LFPs. Additionally, the in vivo-prevailing increase of the electrode impedance and overpotential are discussed and modeled by an ionic mobility-reducing spongiform structure; this restricted diffusion model gives new applicative insight into the in vivo-uprisen stimulation overpotential.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

The popular motor drive systems with a single two-level voltage source inverter (VSI) have one main problem that is the occurrence of the common-mode voltage (CMV), which is an effect of the electromagnetic interference, shaft voltage, bearing currents, leakage current. These cause the high stress, increasung temperature and early mechanical failure in machine. To overcome this problem, the technology of the dual two-level VSI fed open-end three-phase ac loads is now available to eliminate the CMV at the ac/induction motor load with the 120-degree modulation technique for controlling each inverter. In this paper, the discontinuous space vector modulation (DSVM) schemes are proposed and applied for the dual two-level VSI fed open-end load. It is based on the 120-degree modulation technique by using only 12 active voltage vectors and the 10 zero voltage vectors from the total 64 voltage vectors along with the different five-segment swicthing sequence designs with centralizing pulse width modulation technqiue in order to not only cancel the CMV in the ac load, but also reduce the switching number/switching loss of the conversion system. Among the various DSVM schemes, their performances are compared in this paper, such as the number of the switching, the step and peak value of the CMV in each inverter, and the quality of the output waveform, etc. The details of the verfication and comparison are carried out by simulation using Matlab/Simulink software.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

The method for quantitative analysis is based on the direct measurement of the analyte using differential pulse voltammetry (DPV), exploiting its oxidation peak. Calibration curves are set up to evaluate the figures of merit of the analytical method (LOD, LOQ, linear range). The application of the sensor for the dosing of GA in real matrices is carried out by analyzing non-alcoholic and alcoholic beverages and comparing the results with those reported in the literature and with the content of total polyphenols determined by the Folin-Ciocalteu method. In all cases, concentrations of GA align with those previously found in the literature for the beverages examined. Moreover, the values are always lower than the total polyphenols content; this demonstrates the good selectivity of the sensor that can discriminate the target molecule from other polyphenols present.

This review focuses on Cu/TiO2 sequentially and Cu-TiO2 co-sputtered catalytic/photocatalytic surfaces leading to bacterial inactivation discussing their stability, synthesis, adhesion and antibacterial kinetics. The intervention of TiO2, Cu and the synergic effect of Cu and TiO2 on films prepared by a colloidal approach and other techniques is also reviewed leading to bacterial inactivation. Processes in aerobic media and anaerobic media leading to bacterial loss of viability on multidrug resistant (MDR) pathogens, Gram-negative (-) and Gram-positive(+) bacteria are described. Insight is provided for the interfacial charge transfer mechanism under solar irradiation occurring between TiO2 and Cu. surface properties of 2D TiO2/Cu and TiO2-Cu films are correlated with the bacterial inactivation kinetics observed in the dark and under light. The intervention of these antibacterial sputtered surfaces in health-care facilities leading to MRSA-isolates is described in the dark and under the actinic light. The synergic intervention of the Cu and TiO2 films leading to bacterial inactivation prepared by direct current magnetron sputtering (DCMS), pulsed direct current magnetron sputtering (DCMSP) and highly ionized pulse plasma magnetron sputtering (HIPIMS) is reported in a detailed way.

: Seasonal influenza (a.k.a flu) is responsible for considerable morbidity and mortality across the globe. The three recognized pathogens that cause epidemics during the winter season are influenza A, B and C. The influenza virus is particularly dangerous due to its mutability. Vaccines are an effective tool in preventing seasonal influenza, and their formulas are updated yearly according to WHO recommendations. However, in order to facilitate decision-making in the planning of the intervention, policymakers need information on the projected costs and quantities related to introducing the influenza vaccine, in order to help governments obtain an optimal allocation of the vaccine each year. In this paper, an approach based on a Controlled Elitism Non-Dominated Sorting Genetic Algorithm (CENSGA) model is introduced to optimize the allocation of influenza vaccination. A bi-objective model is formulated to control the infection volume, and reduce the unit cost of the vaccination campaign. An SIR (Susceptible–Infected–Recovered) model is employed for representing a potential epidemic. The model constraints are based on the epidemiological model, time management, and vaccine quantity. A two-phase optimization process is proposed: guardian control followed by contingent controls. The proposed approach is an evolutionary metaheuristic multi-objective optimization algorithm with a local search procedure based on a hash table. Moreover, in order to optimize the scheduling of a set of policies over a predetermined time to form a complete campaign, an extended CENSGA is introduced with a variable-length chromosome (VLC) along with mutation and crossover operations. To validate the applicability of the proposed CENSGA, it is compared with the classical Non-Dominated Sorting Genetic Algorithm (NSGA-II). The results are analyzed using graphical and statistical comparisons in terms of cardinality, convergence, distribution and spread quality metrics, illustrating that the proposed CENSGA is effective and useful for determining the optimal vaccination allocation campaigns.

Since its initial development in the 1970’s by Phil Burke and his collaborators, the R-matrix theory and associated computer codes have become the de facto approach for the calculation of accurate data for general electron-atom/ion/molecule collision and photoionization processes. The use of a non-orthonormal set of orbitals based on B-splines, now called the B-spline R-matrix (BSR) approach, was pioneered by Zatsarinny. It has considerably extended the flexibility of the approach and improved particularly the treatment of complex many-electron atomic and ionic targets, for which accurate data are needed in many modelling applications for processes involving low-temperature plasmas. Both the original R-matrix approach and the BSR method have been extended to the interaction of short, intense electromagnetic (EM) radiation with atoms and molecules. Here we provide an overview of the theoretical tools that were required to facilitate the extension of the theory to the time domain. As an example of a practical application, we show results for two-photon ionization of argon by intense short-pulse extreme ultraviolet radiation

Insufficient mixing in large-scale bioreactors, provokes gradient zones of substrate, dissolved oxygen, pH and other parameters. E. coli responds to a high glucose, low oxygen feeding zone with the accumulation of mixed acid fermentation products, especially formate, but also with the synthesis of non-canonical amino acids, such as norvaline, norleucine and -methyl-norleucine. These amino acids can be mis-incorporated into recombinant products, which causes a problem for pharmaceutical production whose solution is not trivial. While these effects can also be observed in scale down bioreactor systems, these are challenging to operate. Especially the high-throughput screening of clone libraries is not easy, as fed-batch cultivations would need to be controlled via repeated glucose pulses with simultaneous oxygen limitation, as has been demonstrated in well controlled robotic systems. Here we show that not only glucose pulses in combination with oxygen limitation can provoke the synthesis of these non-canonical branched-chain amino acids, but also that pyruvate pulses produce the same effect. Therefore we combined the enzyme based glucose delivery method Enbase® in a PALL24 mini-bioreactor system and combined repeated pyruvate pulses with simultaneous reduction of the aeration rate. These cultivation conditions, produced an increase in the non-canonical branched chain amino acids norvaline and norleucine in both the intracellular soluble protein and inclusion body fractions with mini-proinsulin as an example product, and this effect was verified in a 15 L stirred tank bioreactor. To our opinion this cultivation strategy is easy to apply for the screening of strain libraries under standard laboratory conditions if no complex robotic and well controlled parallel cultivation devices are available.

Acute lower respiratory tract infection is a major health problem that affects more than 15% of the total population of Saudi Arabia each year. Epidemiological studies conducted over the last three decades have indicated that viruses are responsible for the majority of these infections. The epidemiology of respiratory viruses in Saudi Arabia is believed to be affected mainly by the presence and mobility of large numbers of foreign workers and the gathering of millions of Muslims in Mecca during the Hajj and Umrah seasons. Knowledge concerning the epidemiology, circulation pattern, and evolutionary kinetics of respiratory viruses in Saudi Arabia are scant, with the available literature being inconsistent. After reviewing the available data on epidemiology and evolution of respiratory viruses, this study examines the effect of varying vaccination rates across different age groups during the 2019/2020 influenza season in Saudi Arabia. Utilizing an age-structured SEIR (Susceptible–Exposed–Infectious–Recovered) model, it develops customized vaccination policies by considering age-specific incidence rates. This pioneering research segments the population into five age groups—infants and school-aged children, junior and older youth, young adults and adults, middle-aged, and seniors—across five regional areas in Saudi Arabis: Eastern, Central, Northern, Western, and Southern. A contact matrix, compiled from multiple sources, is used to delineate the dynamics of influenza transmission. The study undertakes a thorough comparison of three distinct vaccination scenarios: no vaccination, national vaccination, and optimized vaccine allocation policy, under various potential pandemic situations. It examines their impact on vaccination campaigns in terms of the total number of infections, mortality, and morbidity rates. The results emphasize the crucial impact of population demographics on disease transmission and vaccine distribution. According to the findings, the optimized vaccination scenario proved to be the most effective strategy in all scenarios.

This paper presents a study to accurately evaluate defects in reinforced concrete decks using ultrasonic pulse-echo signals. Two validation specimens were designed and tested where reinforced concrete deck slab specimens included planned voids and defects. A commercial Ultrasonic Pulse-Echo (UPE) device obtains 2-D images of the void/defect locations of the reinforced concrete deck. The UPE is based on the ultrasonic shear-wave test method using dry-point-contact transmitting and receiving transducers and employing a synthetic aperture focusing technique. The authors analyzed the recorded UPE A-scan data to enhance the accuracy of estimating the defects' locations using the synthetic aperture focusing technique imaging method. The analysis benefitted from an advanced denoising approach and defect echo peak extraction based on empirical modal decomposition, Hurst exponent characterization, and Hilbert envelope estimation. While output from conventional UPC devices can only provide qualitative results, the new method provides quantitative information on the anomalies inside the reinforced concrete deck. The developed approach accurately assists with assessing the location and depth of the voids/defects in the reinforced concrete deck slabs.

Heel pain in the “funnel-shaped” space between the calcaneus, talus, and talocalcaneonavicular and subtalar joints may be representative of Sinus Tarsi syndrome. The pain is often characterized by a burning, numbness, or tingling sensation that can stem from strains and tears on the ligaments in that area. Injury treatment typically includes balance training, muscle exercises, bracing, foot orthosis, and non-steroidal anti-inflammatory drugs (NSAIDs). This study presents Wharton Jelly (WJ) tissue allografts as an alternative intervention for patients who fail standard-care treatments. WJ targets tissue defects, unlike other therapies, which aim to reduce swelling and symptomatic pain. This study includes five female patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. After an average of 80 days, the cohort had an overall 85.29% improvement in pain. The study's limitations include a small cohort size and a non-blinded design. Given the significant improvement in pain, WJ tissue allograft, combined with other techniques, presents an optimal patient care plan for tissue defects associated with Sinus Tarsi syndrome when standard-of-care treatments fail. These results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

The requirement for developing tools capable of detecting and monitoring heavy metals (HMs) has recently taken on more significance due to worries about their toxic effect on human health and aquatic habitats. In this study, a simple electrochemical sensing carbon paste electrode (CPE) based on composite of Zinc/Iron layered double hydroxide (LDH) and polyaniline (PANI) was developed for the determination of lead ions in aquatic solutions. For this purpose, Zn-Fe LDH/PANI was prepared and characterized by Fourier transform infrared (FTIR), X ray diffraction (XRD), and scanning electron microscopy (SEM). Modified carbon electrode based Zn-Fe LDH/PANI was electrochemically characterized compared with unmodified electrode in FCN as a redox probe using cyclic voltammetry (CV). Thus, Zn-Fe LDH/PANI was utilized as sensing material for the electrochemical determination of lead ions using differential pulse voltammetry (DPV). Zn-Fe LDH/PANI/CPE show limits of detection (LOD) and quantification (LOQ) of 167.8 nM and 559.4 nM, respectively. Zn/Mg/Fe LDH was prepared using co-precipitation method and characterized by XRD, FTIR, SEM and BET, used for removal of Pb+2 ions. Removal process was investigated at different conditions as pH, metal ion concentrations, starting adsorbent dose at first and contact time. Zn/Mg/Fe LDH was evaluated as an effective adsorbent material for lead ions elimination in aquatic solutions, with capacity of adsorption 700 mg/g. The elimination of lead ions on Zn/Mg/Fe LDH fitted the pseudo first-order kinetics model and the isotherm was matched with Langmuir model. Studies revealed that the ideal removal conditions were pH = 5.0, an adsorbent mass of 0.05 g, and 20 ml of 50 ppm metal ion concentration at 60 min. The Zn-Fe LDH/PANI composite also showed potential anti-cancer properties against lung cancer cells (A549) while maintaining safety for normal lung fibroblast cells (WI-38). Collectively, advancements in electrochemical sensors offer promising solutions for lead ion detection, with wide-reaching applications in wastewater treatment and cytotoxicity assessment. These innovations have the potential to enhance environmental monitoring and public health safety.

This paper presents a symmetrical topology for the design of solid-state transformer, made up of power switching converters, to replace conventional bulky transformers. The proposed circuitry not only reduces the overall size but also provides power flow control with the ability to be interfaced with renewable energy resources (RESs) to fulfill the future grid requirements at consumer end. Solid state transformer provides bidirectional power flow with variable voltage and frequency operation and has the ability to maintain unity power factor, and current total harmonic distortion (THD) for any type of load within defined limits of IEEE standard. Solid State Transformer offers much smaller size as compared to that of the conventional iron core transformer. MATLAB/Simulink platform is adopted to test the validity of the proposed circuit for different scenarios by providing the simulation results evaluated at 25 kHz switching frequency.

We previously reported nano-pulse treatment (NPT), a pulsed power technology, resulted in 4T1-luc mammary tumor elimination and a strong in situ vaccination, thereby completely protecting tumor-free animals against a second live tumor challenge. The mechanism whereby NPT mounts effective antitumor immune responses in the 4T1 breast cancer predominantly immunosuppressive tumor microenvironment (TME) remains unanswered. In this study, orthotopic 4T1 mouse breast tumors were treated with NPT (100 ns, 50 kV/cm, 1000 pulses, 3 Hz). Blood, spleen, draining lymph nodes and tumors were harvested at 4-hour, 8-hour, 1-, 3-, 7-day. Additional studies were conducted over 3-month posttreatment intervals for the analysis of frequencies, death and functional markers of various immune cells in addition to suppressor function of regulatory T cells (Tregs). NPT was verified to elicit strong in situ vaccination (ISV) against breast cancer and promoted both acute and long-term T cell memory. NPT abolished immunosuppressive dominance systemically and in the TME by substantially reducing Tregs, myeloid-derived suppressor cells (MDSCs), and tumor-associated macrophages (TAMs). NPT induced apoptosis in Tregs and TAMs. It also functionally diminished the Treg suppression capacity, likely explained by the downregulation of activation markers, particularly 4-1BB and TGFβ, and a phenotypic shift from predominantly activated (CD44+CD62L-) to naïve (CD44-CD62L+) Tregs. Importantly, NPT selectively induced apoptosis in activated Tregs and spared effector CD4+ and CD8+ T cells. These changes were followed by a concomitant rise in CD8+CD103+ tissue-resident memory T cells and TAM M1 polarization. These findings indicate that NPT effectively switches the TME and secondary lymphatic systems from an immunosuppressive to an immunostimulatory state allowing cytotoxic T-cell function and immune memory formation to eliminate cancer cells and account for the NPT in situ vaccination.

Ground-based high-power lasers enable to, in principle, deorbit any kind of space debris object from the low Earth orbit (LEO) by remotely inducing laser-ablative momentum. However, the assessment of efficiency and operational safety depends on many factors like atmospheric constraints or the risk of debris disintegration during irradiation. We analyze laser momentum for a great variety of target geometries and sizes, and – for the first time in a large-scale simulation – include thermal constraints for laser irradiation configuration. Using a coherently coupled 100 kJ laser system at 1030 nm wavelength, 5 ns pulse duration in an optimized pointing elevation angle range, the pulse frequency should amount to less than 10 Hz to prevent fragment meltdown. For mechanically intact payloads or rocket bodies, repetition rates should be even lower. Small debris fragments sized between 10 and 40 cm can be de-orbited by around 100 to 400 station passes with head-on irradiation while objects exceeding 2 m typically require far more than 1000 irradiations for deorbit. Hence, laser-based debris removal cannot be considered a prime space sustainability measure tackling the top-risk large debris, yet it can provide for remediation of a multitude of small-sized debris using small networks of globally distributed laser sites.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

This case report demonstrates the rare but potentially serious complication of pulmonary vein stenosis (PVS) diagnosed several years after radiofrequency ablation for atrial fibrillation. Pulmonary vein stenosis can remain asymptomatic until significant occlusion occurs, after which it can present with a variety of symptoms, mimicking numerous cardiovascular and pulmonary pathologies. Early diagnosis and treatment rely on consistent follow-up using appropriate diagnostic imaging modalities, which are paramount in preventing severe complications.