This paper presents the results of a comparison of the seasonal dynamics of carbon dioxide content in the atmosphere and the phenological phases of various water bodies located in the boreal and subarctic zones for 2012–2020. Six large freshwater areas were selected as research objects: Lake Baikal, Lake Ladoga, Gulf of Ob, Lake Huron, Great Bear Lake and Great Slave Lake. In addition, four areas of wetlands in Western Siberia were studied. The CO2 concentration in the air column over water bodies was obtained from CAMS global greenhouse gas reanalysis data. These data represent three-dimensional fields of aerosols and chemical components in the atmosphere, with complete coverage of the globe. The phenological phases of the water bodies were determined using data from the MIRAS microwave radiometer of the SMOS satellite. The comparison and analysis performed showed that the concentration of CO2 in the atmosphere over the studied water bodies has a seasonal cyclical nature. The minimum concentration corresponds to the summer period due to strong photosynthesis of phytoplankton and swamp vegetation, which results in the absorption of carbon dioxide. The maximum CO2 concentration over the water bodies corresponds to the end of the winter – the beginning of the spring period, when photosynthesis processes are minimal. During this period, CO2 is being accumulated in water bodies and subsequently emitted. In freezing lakes located in the boreal zone, in addition to a stable spring maximum of CO2, a strong short-term release of carbon dioxide is sometimes observed, also corresponding to the stage of destruction of the ice cover. It is associated with the release of CO2 accumulated over the winter period, which was “sealed” in the ice and in the water column under the ice. The absence of such a release in the waters of the subarctic zone is explained by the lower biological productivity of these reservoirs compared to the waters of the boreal zone.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

Phytochemicals from Hedera helix L. lead to extracts with good biological properties which are beneficial to human health and can be used to protect plants against different diseases. The aim of this research was to find the most suitable extraction method and the most favorable parameters for different bioactive compounds extraction from ivy leaves. Different extraction methods, namely microwave assisted extraction (MAE), ultrasound assisted extraction (UAE), and conventional heating extraction (CHE), were used. The most suitable method for saponins extraction is MAE with an extraction efficiency of 58%, while for carbohydrates and polyphenols the best results were achieved by UAE with an extraction efficiency of 61.7% and 63.5%, respectively. The antioxidant activity (AA) of the extracts was also determined. The highest AA was obtained by UAE (368.98±9.01 µmol TR/gDM). Better results were achieved at 50 °C for 10 min of extraction, using 80% ethanol in water as solvent. In order to evaluate their in vitro cytotoxicity, the extracts richest in bioactive compounds were tested on NCTC fibroblasts. Their influence on the DNA content of RAW 264.7 murine macrophages was also tested. Until 200 µg/mL, the extracts obtained by UAE and MAE were cytocompatible with NCTC fibroblasts at 48 h of treatment.

This study aims to evaluate the combined assimilation of AGRI infrared radiance and ground-based MWR (Microwave Radiometer) data for predicting short-duration heavy rainfall. The WRFDA 4.3 framework is utilized to establish the data assimilation interface. The structural characteristics of this joint assimilation approach are analyzed using a typical heavy rainfall event in the Kaifeng region of Central China. The findings indicate the following: (1) The joint assimilation of FY-4A AGRI and ground-based MWR data effectively corrects the initial moisture content in model simulations. Data assimilation significantly improves the simulation of 24-hour accumulated rainfall. Furthermore, the joint assimilation of AGRI radiance and MWR data outperforms assimilating either of them individually; (2) In the heavy rainfall stage, from the low level to the high level, strong upward movement occurs in the center of the rainstorm. The water vapor in the process of this rainstorm mainly comes from the westward air transport in front of the high trough. The water vapor is continuously transported to the heavy rainfall belt through this channel, providing sufficient water vapor for the maintenance of the rainstorm; (3) The combination of the interaction between high and low level vorticity and divergence in the atmosphere and the vertical upward movement, the emergence of low level jet and the generation of unstable energy in the atmospheric environment jointly lead to the occurrence of the rainstorm process; and (4) The terrain-sensitive experiment results show that, the existence of the topography of Taihang Mountain changes the precipitation in Kaifeng area, and reducing the terrain height will lead to a 50%-60% decrease in the overall precipitation of the precipitation center, and the precipitation range will also be greatly reduced. An increase of more than 50% in terrain height will lead to an increase in precipitation center, precipitation range and precipitation intensity, and an increase of 10%-20% in overall precipitation; An increase of more than 75% in the terrain height will cause the rain belt to shift eastward by about 0.5°E, and the precipitation center will shift significantly eastward. When the terrain height increased by more than 100%, the precipitation did not continue to increase, which was basically the same as the control test. This paper provides a valuable basis for further improving the application of FY-4A AGRI radiance and ground-based microwave radiometer in numerical weather models.

The root extracts of Symphytum officinale (comfrey) are commonly used in traditional medicine to treat muscle, joint, skin and bone disorders. However, little information is available on the biomedical functions of comfrey leaves. In this study, sequencing results of Internal Transcribed Spacer and trnL-trnF genes showed that plants purchased from the local market were comfrey and named as S. officinale WL (WL). The optimal extraction conditions of WL leave with the highest extract yield and contents of total phenols and flavonoids by microwave-assisted extraction were identified. The antioxidative and anti-inflammatory activities and possible molecular mechanism(s) of the WL leaf extract (WLE) were evaluated. Furthermore, the major component of WLE was identified as rosmarinic acid by HPLC. Results showed that the optimal extract condition was obtained with 750W microwave power, 50℃, 75% methanol, the solid-to-solvent ratio of 1:10, and 15 minutes. Results of all DPPH, ABTS and superoxide radical scavenging activities, reducing power, ferrous ion chelating activity, and ferric reducing antioxidant power showed high antioxidative capacities of WLE. Furthermore, WLE showed obvious DNA protecting activity. WLE attenuated lipopolysaccharides-stimulated inflammation by suppressing iNOS, COX-2, IL-1β, IL-6, and TNF-α expressions in RAW264.7 macrophages. These attenuations involved in inactivations of lipopolysaccharides-induced NF-κB and MAPK signaling pathways.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

Feedback control plays a crucial role in improving system accuracy and stability for a variety of scientific and engineering applications. Here, we theoretically and experimentally investigate the implementation of feedback control in microwave photonic (MWP) transversal filter systems based on optical microcomb sources, which offer advantages in achieving highly reconfigurable processing functions without requiring changes to hardware. We propose four different feedback control methods including (1) one-stage spectral power reshaping, (2) one-stage impulse response reshaping, (3) two-stage spectral power reshaping, and (4) two-stage synergic spectral power reshaping and impulse response reshaping. We experimentally implement these feedback control methods and compare their performance. The results show that the feedback control can significantly improve not only the accuracy of comb line shaping as well as temporal signal processing and spectral filtering, but also the system’s long-term stability. Finally, we discuss the current limitations and future prospects for optimizing feedback control in microcomb-based MWP transversal filter systems implemented by both discrete components and integrated chips. Our results provide a comprehensive guide for the implementation of feedback control in microcomb-based MWP filter systems in order to improve their performance for practical applications.

In this paper, the extraction of essential oil (EO) from thyme by consecutive use of ultrasound and microwave treatments is presented. The aim of the study was to apply an ultrasound pre-treatment of thyme leaves to enhance the thymol content and the extraction yield of the EO obtained by microwave-assisted hydro-distillation (MWHD). Compared with the conventional hydro-distillation (CHD), the consecutive use of ultrasound and microwave treatments resulted in a 72% lower extraction time. When the ultrasound pre-treatment (using the ultrasonic processor with an amplitude of 70%) was applied, the EO content was 23% higher compared to the extraction without pre-treatment. The EO samples were analyzed by GC/MS. The results showed that the major component, thymol, varied from 43.54% (by CHD) to 65.94% (by consecutive use of ultrasound and microwave treatments).

Background and aim We investigated the clinical outcomes of patients with hepatocellular carcinoma (HCC) who underwent next-generation microwave thermosphere ablation (MTA). Methods A total of 429 patients with 607 HCCs (maximum tumor diameter ≤40 mm) were included. Results The primary etiologies of HCC were hepatitis-related: 259 (60.4%) cases of HCV, 31 (7.3%) cases of HBV, and two instances of both. Median maximum tumor diameter was 15.0 (interquartile range, 10.0–21.0) mm. There were 86 tumors in areas of the liver where MTA is difficult. The most common area was near the primary and secondary branches of the intrahepatic portal vein (26 nodules). The cumulative local tumor recurrence rates at 1, 2, and 3 years were 4.4%, 8.0%, and 8.5%, respectively. The cumulative local tumor recurrence rate differed significantly by tumor size group: ≤20 mm group (n=483), 20–30 mm group (n=107), and ≥30 mm group (n=17) (p<0.001). The cumulative local tumor recurrence rate was similar by difficult-to-treat status (p=0.169). In the multivariable analysis, tumor size (per 1 mm) (hazard ratio [HR], 1.07; 95% confidence interval [CI], 1.03–1.11; p<0.001) and ablative margin (per 1 mm) (HR, 0.81; 95% CI, 0.70–0.92; p=0.002) were significantly associated with local tumor recurrence. Only tumor size (per 1 mm) (odds ratio, 1.08; 95% CI, 1.02–1.15; p=0.015) was significantly associated with complications. Conclusions MTA is a safe and effective local ablation therapy for HCC, even for tumors located in areas of the liver where local ablation therapy is difficult.

The microwave field is used for drying and disinfection of grain, during pre-sowing seed treat-ment. The use of a microwave field in these installations leads to an increase in their productivity and a decrease in the energy consumed by them. One of the principal problems of microwave field use for treatment of dense grain layers is to insure sufficient distribution uniformity of the field. In this article, waveguide design options have been discussed that serve to introduce microwave radiation into the grain layer. Mathematical simulation of the electromagnetic field distribution was performed with the use of CST Microwave Studio software in order to evaluate and compare horn-type, rectangular and semicircular waveguides. The data on the standing wave ratio and radiation efficiency for these types of waveguides have been reported. Specific features of the microwave electromagnetic field distribution and radiation power in the output of those wave-guides have been described. Results of mathematical simulations enabled to make out that sem-icircular waveguides with slot-type radiators are preferable for processing dense grain layers.

Wild strawberry (Fragaria vesca L.) leaves possess diverse antioxidant properties, mainly due to the different classes of phenolics. In this study, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) of wild strawberry phenolics were carried out to understand the impact of extraction temperature, extraction time and solvent-to-sample ratio (SSR) on the quantitative and qualitative properties of the obtained extracts. The highest total phenolic content (8027 mg GA/100 g DW), as well the highest DPPH• antiradical activity (903 mol TE/g DW) was obtained with ASE at 150 °C, static time 5 min and SSR of 40:1; while the highest ABTS•+ antiradical activity (681 mol TE/g DW,) and FRAP (2389 mol TE/g DW) was obtained with MAE after 5 min at 80 °C and a SSR of 40:1. The correlation analysis showed that phenolics largely contributed to the antioxidant properties of the studied MAE extracts, while correlation was not found in ASE extracts. A total of 54 different phenolics were identified by UPLC/MS-MS in MAE and ASE extracts obtained at optimal extraction conditions. MAE extract was shown to have a higher content of phenolic acids (40%), but lower content of proanthocyanidins (88%), flavonols (29%), flavan-3-ols (50%) and flavones (39%) than ASE extract.

The presented work studies the processes of synthesis of nitrogen-containing structures of ZnO using atmospheric pressure microwave nitrogen plasma and investigates their photocatalytic activity in the processes of degradation of 2,4-dinitrophenol and the antibiotic ciprofloxacin when irradiated with sunlight. The work proposes an effective method for formation of photosensitive ZnO powders. Due to the features of plasma treatment in the open atmosphere of zinc metal microparticles, ZnO structures are formed with sizes from hundreds of nanometers to several micrometers with various micromorphologies. High photoactivity was demonstrated (rate constants 0.036 min-1 and 0.051 min-1) of synthesized ZnO structures during photo-degradation of 2,4-dinitrophenol and ciprofloxacin, respectively, when exposed to solar radiation. Photo-active structures of ZnO synthesized using microwave nitrogen plasma can find application in processes of mineralization of toxic organic compounds.

Alginate, a biopolymer promising in food, biomedical, pharmaceutical, and electronic materials industries, is characterized by its biodegradability, biocompatibility, low toxicity, and gel-forming properties. It is most abundantly found in brown algae. However, conventional dilute acid and alkali extraction methods face limitations in commercialization due to their long processing time, low throughput, and high solvent requirements. In this study, a microwave-assisted extraction (MAE) process for sodium alginate was designed to improve extraction efficiency. Solid/liquid ratio, extraction temperature, and extraction solvent concentration were major variables affecting sodium alginate extraction from Undaria pinnatifida(sea mustard). They were then statistically optimized using response surface methodology. Under optimal conditions (13.27 g/L, 91.86 ℃, 2.51 %(w/v), and 15 min), the yield was 38.41 %, which was 93.43 % of the theoretical content of sodium alginate in Undaria pinnatifida. Our work has confirmed the productivity and industrial feasibility of efficient extraction of sodium alginate from marine biomass, and we hope that it will serve as an encouraging case for the application of biopolymers as one of the desirable options for alternative petrochemicals to construct a sustainable society.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

We report a dual-polarization radio frequency (RF) channelizer based on microcombs. With the tailored mismatch between the FSRs of the active and passive MRRs, wideband RF spectra can be channelized into multiple segments featuring digital-compatible bandwidths via the Vernier effect. Due to the use of dual-polarization states, the number of channelized spectral segments, and thus the RF instantaneous bandwidth (with a certain spectral resolution), can be doubled. In our experiments, we used 20 microcomb lines with ~ 49 GHz FSR to achieve 20 channels for each polarization, with high RF spectra slicing resolutions at 144 MHz (TE) and 163 MHz (TM), respectively; achieving an instantaneous RF operation bandwidth of 3.1 GHz (TE) and 2.2 GHz (TM). Our approach paves the path towards monolithically integrated photonic RF receivers (the key components—active and passive MRRs are all fabricated on the same platform) with reduced complexity, size, and unprecedented performance, which is important for wide RF applications with digital-compatible signal detection.

Focused microwave breast hyperthermia (FMBH) employs a phased antenna array to perform beamforming that can focus microwave energy at targeted breast tumors. Selective heating of the tumor endows the hyperthermia treatment with high accuracy and low side effects. The effect of FMBH is highly dependent on the applied phased antenna array. This work investigates the effect of polarizations of antenna elements on the microwave focusing results by simulations. We explore two kinds of antenna arrays with the same number of elements using different digital realistic human breast phantoms. The first array has all the elements’ polarization in the vertical plane of the breast while the second array has half elements’ polarization in the vertical plane and the other half in the transverse plane, i.e., cross polarization. In total 96 sets of different simulations are performed, and the results show that the second array leads to a better focusing effect in dense breasts than the first array. This work is very meaningful for the potential improvement of the antenna array for FMBH, which is of great significance for the future clinical applications of FMBH. The antenna array with cross polarization can also be applied in micro-wave imaging and sensing for biomedical applications.

Microwave transversal filters, which are implemented based on the transversal filter structure in digital signal processing, offer a high reconfigurability for achieving a variety of signal processing functions without changing hardware. When implemented using microwave photonic (MWP) technologies, also known as MWP transversal filters, they provide competitive advantages over their electrical counterparts, such as low loss, large operation bandwidth, and strong immunity to electromagnetic interference. Recent advances in high-performance optical microcombs provide compact and powerful multi-wavelength sources for MWP transversal filters that require a larger number of wavelength channels to achieve high performance, allowing for the demonstration of a diverse range of filter functions with improved performance and new features. Here, we present a comprehensive performance analysis for microcomb-based MWP spectral filters based on the transversal filter approach. First, we investigate the theoretical limitations in the filter spectral response induced by finite tap numbers. Next, we analyze the distortions in the filter spectral response resulting from experimental error sources. Finally, we assess the influence of input signal’s bandwidth on the filtering errors. These results provide a valuable guide for the design and optimization of microcomb-based MWP transversal filters for a variety of applications.

: Low-temperature growth of diamond films by chemical vapor deposition (CVD) method is not so widely reported and especially its initial periods of nucleation and growth phenomenon are of particular interest to the researchers. Four sets of substrates were selected for growing diamond films by linear antenna microwave plasma enhanced CVD (LA-MPCVD). Among them, silicon and sapphire substrates were pre-treated with detonation nanodiamond (DND) seeds before diamond growth for enhancement of its nucleation. On the other hand, carbon nanotube (CNT) films on Si substrates were also used as another template for LA-MPCVD diamond growth. In order to enhance the diamond nucleation during CVD growth, some of the CNT films were again pre-treated by electrophoretic deposition (EPD) of diamond nanoparticles. All these substrates were then put inside the LA-MPCVD chamber for growing diamond films under variable processing conditions. Microwave input powers (1100 – 2800 W), input power modes (pulse or continuous), antenna to stage distances (5 - 6.5 cm), process gas recipes (with or without CO2), methane gas percentages (3 - 5%), deposition times (11 – 120 minutes) were altered to investigate their effect on the growth of diamond film on the pre-treated substrates. The substrate temperatures were found to vary from as low as 170oC to a maximum of 307oC during the alteration of the different processing parameters. Contrary to the conventional MPCVD, it was observed that during the first hour of LA-MPCVD diamond growth, DND seeds or the nucleating structures, do not coalesce together to make a continuous film. Deposition time was the most critical factor in fully covering the substrate surfaces with diamond film, since the substrate temperature could not become stable during the first hour of LA-MPCVD. CNT was found to be oxidised rapidly under LA-MPCVD plasma conditions; therefore, a CO2-free process gas recipe was used to reduce CNT burning. Moreover, EPD-coated CNT was found to be less oxidised by the LACVD plasma during diamond growth.

Microwave photonic (MWP) signal processors, which process microwave signals based on photonic technologies, bring advantages intrinsic to photonics such as low loss, large processing bandwidth, and strong immunity to electromagnetic interference. Optical microcombs can offer a large number of wavelength channels and compact device footprints, which make them powerful multi-wavelength sources for MWP signal processors to realize a variety of processing functions. In this paper, we experimentally demonstrate the capability of microcomb-based MWP signal processors to handle diverse input signal waveforms. In addition, we quantify the processing accuracy for different input signal waveforms, including Gaussian, triangle, parabolic, super Gaussian, and nearly square waveforms. Finally, we analyze the factors contributing to the difference in the processing accuracy among the different input waveforms, and our theoretical analysis well elucidates the experimental results. These results provide a guidance for microcomb-based MWP signal processors when processing microwave signals of various waveforms.

This paper presents for the first time the design of a microwave sensing setup for the potential monitoring and identification of red palm weevil (RPW) gender type. The microwave sensor consists of a planar two-port transmission line (TL) with a single complementary split-ring resonant (CSRR) inclusion etched from the bottom metallic layer. The CSRR sensor is placed on top of a customized non-conductive container. The microwave sensing setup has been designed, numerically demonstrated, fabricated and tested experimentally. Simulated results correlate quite well with the experimental data. Moreover, the sensitivity of the CSRR sensor when in close proximity to different RPW gender has been evaluated both numerically and experimentally. Based on the measured results from 15 RPW collected samples with different body sizes, different RPW gender types showed unique microwave signatures. Notable shift to the sensor's resonance frequency has been achieved, where on average a resonant frequency shift of 10% for adult RPWs was achieved, while 2.4% frequency change was obtained for larvae (young) RPWs. Hence, the proposed microwave sensing setup can be adopted in field trials to examine and differentiate between various RPW genders at various development stages.

In the work the enhanced security of unmanned aerial vehicles (UAVs) electronics in RF environment was investigated. UAVs are commonly used in many areas and the cellular networks as the parallel helping networks for systems: LTE, 5G or especially for future 6G are very perspective and needed. For effective communications in channels: “air-to-ground” as well as “drone-to-drone” the important task is undisturbed work of transportation platforms, ie. UAV. However, high level of outside electromagnetic radiation can affect the correct electronics work. The problem is due to non-conformity of RF environment regulations. The electromagnetic compatibility (EMC) standards guarantee correct electronics work when the radiation level is not higher than established EMC levels. In case of commercially available devices, like UAVs, this level is 3 V/m. On the other hand, permissive exposure level, treated as RF environment emitted by cellular base stations, can reach the level of 61 V/m. Such level of electromagnetic wave pollution, can damage unprotected electronics with fatal consequences. This can cause the unchecked drone flight or unchecked fall down. As a result, due to unchecked flight, the UAV can cause the sudden communication interruption with operator or other drones. To reduce the level of damaging RF field we propose to cover the UAV housing with microwave absorber. In this case absorber must ensure good electromagnetic protection as well as lightweight and resistant on weather conditions. The shielding property of reduced graphene oxide (RGO) as an absorber was investigated. For proposed material the shielding effectiveness (SE) was investigated in the frequency range from 100 MHz to 10 GHz. It has been proved that such material can be a good candidate as an absorber for UAV having low reflection coefficient and high absorption ability. In this work the shielding effectiveness of RGO was analyzed for two layers of 3 and 5 mm at typical frequencies as RF environment, ie. 3.6 GHz (5G system) and 5.8 GHz (LTE). Investigated absorber guarantees the value of SE of 25 dB and 30 dB for 3 mm layer at 3.6 GHz and 5.8 GHz respectively and of 29 dB and 39.5 dB for 5 mm layer at these frequencies respectively.

This paper is dedicated to examining dynamic dark energy models in the context of observational constraints and their implications for the universe's future. By integrating theoretical models with various observational data, we aim to provide a comprehensive view of how dynamic dark energy influences cosmic evolution and the universe's fate. This study tests these models against the latest observational evidence, including the Cosmic Microwave Background, supernovae, and large-scale structure surveys, to refine our understanding of the universe's accelerating expansion and the mysterious nature of dark energy.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

In India, particularly within its North-Eastern territories, the occurrence of landslides triggered by post-dry period rainfall events is a significant concern, with the phenomena persistently causing extensive damage to both life and infrastructure. Despite the inevitability of such natural disasters, it is understood that the impact they exert can be substantially mitigated through the implementation of pre-emptive measures. Critical to the endeavour of landslide prevention is the application of a spectrum of mitigation strategies, predicated upon a foundational analysis of slope stability to ascertain critical surfaces for intervention. This investigation delves into the dynamics of partially saturated soils, a condition commonly resultant from the prolonged dry periods preceding the monsoonal rains. The study's focal point is an experimental examination conducted on soil samples to assess parameters such as soil matric suction and unconfined compressive strength across varying degrees of saturation and density, alongside performing analyses of slope failure incidents after dry period during the 2017 monsoon in the Lunglei district, Mizoram based on some established data. The Soil-Water Characteristic Curve (SWCC), derived from soil suction measurements employing the ASTM D5298-10 standard, utilizes a contact filter paper method and serves to delineate the moisture transition phases of the slope. To replicate the desiccation of the soil slope after monsoonal rains, a microwave drying technique based on the ASTM standard was employed to prepare unsaturated soil samples for Unconfined Compressive Strength (UCS) testing. The integrity of the slope was evaluated in a temporal context, before and after rainfall events of varied intensities throughout the calendar year, utilizing a blend of numerical modeling and empirical laboratory investigations. The persistence of real onsite slope failures underscores the necessity for a numerical analysis approach to unravel the underlying factors causing slope instability, especially given the absence of prior stability assessments for the landslide in question. An evaluation of SWCC curves, UCS tests on partially saturated soil at different densities and saturation and the utilization of the benchmark data collected in 2017 on the shallow transitional landslide in Lunglei, Mizoram caused by intense monsoonal precipitation, are central key data and information used to carry out this research. Rainfall data for Lunglei, sourced from the Mizoram Meteorological Department, facilitated a real-time monsoonal data-driven numerical analysis. This analysis elucidated the pivotal role of rainfall in inducing slope failure, indicating a marked destabilization of the slope after precipitation events. The implications of these findings are far-reaching, suggesting a foundational basis for the development of an advanced landslide early warning system, thereby enhancing disaster preparedness, and mitigating potential damages.

Chert rock is a by-product of sand quarrying (about 40% in the geological section). All attempts to use ordinary technologies for aggregate production from chert have been economically unsuccessful, resulting in significant chert "waste" accumulation covering vast quarry areas. This paper presents the study results of the effect of microwave irradiation on the mechanical properties of chert gravel, which is mineralogically relatively homogenous and consists of fine quartz grains. The results show that an increase in irradiation time decreases the strength of chert gravel (by a factor of 4-6 for the 2.5 min of irradiation), while the quenching changes the fractional content of the samples after the crushing test, decreasing the Gravel-to-Sand ratio.

This study aims to exploit the distinctive properties of carbon nanotube materials, which are particularly pronounced at the microscopic scale, by deploying fabrication techniques that allow their features to be observed macroscopically. Specifically, we aim to create a semiconductor device that exhibits flexibility and the ability to modulate its electromagnetic wave absorption frequency by means of biasing. Initially, we fabricate a sheet of carbon nanotubes through a vacuum filtration process. Subsequently, phosphorus and boron elements are separately doped into the nanotube sheet, enabling it to embody the characteristics of a PN diode. Measurements indicate that, in addition to the fundamental diode's current-voltage relationship, the device also demonstrates intriguing transmission properties under the TEM mode of electromagnetic waves. It exhibits a frequency shift of approximately 2.3125 GHz for each volt of bias change. The final result is a lightweight and flexible carbon-based semiconductor microwave filter, which can conform to curved surfaces. This feat underscores the potential of such materials for innovative and effective electromagnetic wave manipulation.

This study aimed to evaluate the effect of convective and microwave drying on the content of bioactive compounds of blackberry (Rubus fruticosus), drying parameters and energy consumption. The fruit was dehydrated in a convective dehydrator at a temperature of 50 °C and 70 °C and a microwave oven at power levels of 90 V, 180 V and 240 V. The highest amount of anthocyanins, polyphenols and antioxidant capacity were obtained in microwave dried blackberry fruits at 90 V and 180 V. It turned out that microwave dehydration shortened the processing time and lower the energy consumption compared to the convective drying. Blackberry fruits dehydrated at 240 V showed the shortest dehydration time, minimal energy consumption and the most efficient diffusion.

The influences of doped hole transporting layer (HTL) on the performances of perovskite solar cells were studied. The influences of electrostatic and surface roughness effect by solvent additive doping were compared. The electrostatic effect of solvent additive doping was compared by addition of 1,8-diiodooctane and 1,8-dichlorooctane to the HTL layer. The surface roughness effect of solvent additive doping was examined using atomic force microscopy. The perovskite crystallinity by doping HTL was studied by X-ray diffraction. The conductivity of HTL was measured using four probe methods and was higher for doped devices. Enhanced conductivity of PEDOT:PSS film was also proved using fluorescence emission quenching. Long-term stability of the device was enhanced by doping HTL. The device with solvent additive exhibited much enhanced stability, retained over 80% of the initial PCE for 400 hours, while PCE of the device without solvent additive decreased to less than 80% after 200 hours. A very weak power microwave treatment was used for post-annealing of the fully fabricated devices. Post-annealing enhanced the lifetime of the device. Comparing different size of cells, the device lifetime was decreased as the cell area increased and as the size of the cell increased, the extent of lifetime enhancement by doping was increased.

Traditional methods of non-metallic materials joining for industrial uses are limited to lasers, or induction or conduction heating. The precision and efficiency for large-scale applications are difficult to be achieved at the same time. Here in this paper, we report a precise microwave welding method induced by localized surface plasmon of metallic macro-gaps under microwave excitation. The proposed method utilizes energy from well-developed commercial microwaver, and benefits from the precision of localized surface plasmon, an oscillating electron cloud excited by electromagnetic waves, which is currently under hot investigation only at micro- or nano-scales. The method is applied to the welding of polymers to solve the problems of complex processing equipment and high processing energy consumption in the traditional welding process, so as to cope with the growing energy and environmental crisis. Finite element numerical simulations are used to study the distribution characteristics of electric fields and temperature fields. The results show that the process is a high quality, efficient, low consumption and environmentally friendly green process compared to traditional polymer welding methods.

This paper presents a novel high-power rotary waveguide phase shifter based on circular polarizers specifically engineered for high-power microwave (HPM) applications. The phase shifter is capable of performing a precise 360° linear phase shift through rotation and consists of three parts: a linear polarized to left-handed circular polarized (LP-LHCP) mode converter, a left-handed to right-handed circular polarized (LH-RHCP) mode converter, and a linear polarized to right-handed circular polarized (LP-RHCP) mode converter. The paper analyzes the phase shifting principle, optimizes the three parts of the X-band rotary waveguide phase shifter, and conducts simulation studies on the entire phase shifter made of aluminum. The results show that the reflection is less than -20dB and the transmission efficiency is over 95% within 9.5GHz to 10.2GHz. The phase shift has a linear relationship with the rotation angle by a factor of two within this frequency range. Specifically, the phase shifter can achieve a linear phase shift of 360° when rotated from 0° to 180°, with a maximum deviation of less than 1.2°. Moreover, the power-handling capacity of the phase shifter in vacuum exceeds 242mW.

In this study, we investigate Quantum Entanglement Asymmetry (QEA) as a potential explanation for the matter-antimatter imbalance observed in the universe. By integrating quantum mechanics with cosmological phenomena, the study proposes a model in which quantum entanglement among particle-antiparticle pairs in the early universe leads to an asymmetry favoring matter. Through theoretical development and numerical simulations, we explore how this model predicts unique patterns in Cosmic Microwave Background (CMB) anisotropies and the distribution of matter, setting a foundation for empirical verification. The study aims to enhance the understanding of cosmological asymmetries and highlight the significance of quantum entanglement in the universe's evolution.

This study develops a wavelet maxima-based methodology to extract anomalous signals from microwave brightness temperature (MBT) observations for seismic estimation. MBT, acquired via satellite microwave radiometry, enables subsurface characterization penetrating clouds. Five earthquake categories were defined contingent on locale (oceanic/terrestrial) and ambient traits (soil hydration, vegetal covering). Continuous wavelet transform was applied to preprocess annualized MBT readings preceding and succeeding prototypical events of each grouping, utilizing optimized wavelet functions and orders tailored to individualized contexts. Wavelet maxima graphs visually portraying signal intensity variations facilitated identification of aberrant phenomena, including pre-seismic accrual, co-seismic perturbation, and postsismic remission signatures. Casework found 10GHz horizontal-polarized MBT optimally detected signals for aquatic and predominantly humid/vegetative settings, whereas 36GHz horizontal-polarized performed best for arid, vegetated landmasses. This preliminary investigation establishes an analytical framework, albeit reliant on qualitative appraisals. Quantitative machine learning methods are warranted to statistically define selection standards and augment empirical forecasting leveraging lithospheric stress state inferences from sensitive MBT parametrization.

Abstract: The objective of these studies was to determine the dependence of the distribution of the microwave field into a grain layer and the efficiency of energy transfer from the magnetron into the grain layer, via a waveguide, on the moisture content. The subject of the research was a semicircular waveguide with slot radiators that supply a microwave field to the grain surrounding the waveguide. The change in the directional diagram of the microwave field in the longitudinal direction of the waveguide was studied using CST Microwave Studio 2019 software. It was found that the change in the moisture content of the processed grain leads to a significant change in both the radiation and total efficiency values of the waveguide. For instance, the radiation efficiency of the waveguide decreases by 15.1% (from 68.729 dB to 58.294 dB) when the moisture content of the processed grain increases from 14% to 26%. The total radiation efficiency also decreases (from 11.27 dB to 21.7 dB). In this case, not only the value of the radiation efficiency but also the shape of its dependence on the magnetron radiation frequency change. Data were obtained on the change in the Q-factor for resonators in which grain layers are processed, depending on the variation in grain moisture content.

This study presents the utilization of the Microwave InfraRed Thermography (MIRT) technique to identify and analyze the defects in the carbon-fiber-reinforced polymer (CFRP) composite rein-forcement of concrete specimens. At first, a set of the numerical models was created, comprising of the broadband pyramidal horn antenna and the analyzed specimen. The utilization the system operating at a power of 1000W in a continuous mode, operating at frequency of 2.45 GHz was analyzed. The specimen under examination comprised a compact concrete slab that was covered with an adhesive layer, thereafter, topped with a layer of CFRP. An air gap represented a defect at the interface between the concrete and CFRP within the adhesive layer. In the modelling stage the study investigated three separate scenarios: a sample with no defects, a sample with a defect located at the center, and a sample with a numerous additional random defects located at the rim of the CFRP matte, to analyze the effect of the natural reinforcement degradation in this area. The next phase of the study involved conducting experiments to confirm the results obtained from nu-merical modeling. In the experiments the concrete sample aged for 10 years with the defect in the center and naturally developed defects at the CFRP rim was used. The study employed numerical modeling to explore the phenomenon of microwave heating in complex structures. The aim was to assess the chosen antenna design and identify the most effective experimental setup. These con-clusions were subsequently confirmed through experimentation. The observations made during the heating process were particularly remarkable, since they deviated from earlier studies that solely conducted measurements of the sample post-heating phase. The findings demonstrate that MIRT has the capacity to be employed as a technique for detecting flaws in concrete structures reinforced with CFRP.

This work presents preliminary experimental results advancing non-destructive testing methods for detecting steel bars in concrete structures via contactless investigation in the X-band spectrum. The study reveals the field’s penetration into concrete, extracting insights into embedded bars through scattered data. Applying a quasi-quadratic inverse scattering technique to numerically simulated data yields promising results, confirming the effectiveness and reliability of the proposed approach. In this realm, using a higher frequency allows the use of lighter equipment and smaller antennas. Identified areas for improvement include accounting for antenna behavior and establishing undeformed target morphology and precise orientation. Transitioning from powder-based and sand specimens to real solid reinforced concrete structures is expected to alleviate laboratory challenges. Although accurately determining concrete properties such as relative permittivity and conductivity is essential, it remains beyond the scope of this study. Finally, overcoming these challenges could significantly enhance non-invasive testing, improving structural health monitoring and disaster prevention.

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.