Keywords: SAR; interferometry; bistatic

This article proposes an interferometer which should in principle split further an initially split beam to yield new sets of beams, effectively multiplying the number of beams that can be subjected to detectable interference. It can be considered a modification to the Michelson interferometer that introduces additional arrays of beam splitters, mirrors and detectors. It is expected of the interferometer to provide us with a set or sets of data holding details of phase changes in multiple interference patterns detectable by multiple detectors, enabling comparative analysis of data for multiple interference patterns recorded from a single measurement or activity. The number of multiplied beams possible is not limited, as it only depends on the specific amount of beam splitters required for certain experiments and practicals. The interference of multiple beams may improve sensitivity and detection for instrumentation purposes. The use of multiplied beam interferometry may also extend to quantum computation, particularly in linear optical quantum computation scheme as it enable production of multiple coherent beams which may exhibit properties of entanglement, making it suitable for developing optical multi-qubit systems.

Aptamers are excellent choices for selective detection of small molecules. However, the previously reported aptamer for chloramphenicol suffers from low affinity, probably as a result of steric hin-drance due to its bulky nature (80 nucleotides) leading to lower sensitivity in analytical assays. The present work was aimed at improving this binding affinity by truncating the aptamer without compromising its stability and three-dimensional folding. Shorter aptamer sequences were designed by systematically removing bases from each or both ends of the original aptamer. Thermodynamic factors were evaluated computationally to give insights into the stability and folding patterns of the modified aptamers. Binding affinities were evaluated by bio-layer interferometry. Among the 11 sequences generated, one aptamer was selected based on its low dissociation constant, length and regression of model fitting with association and dissociation curves. The dissociation constant could be lowered by 86.93% by truncating 30 bases from the 3’ end of the previously reported aptamer. The selected aptamer was used for gold nanospheres based colorimetric detection of chloram-phenicol in real samples. The detection limit could be reduced 32.87 times (1.673 pg mL-1) using the modified length aptamer, indicating its improved affinity as well as suitability in real sample analysis for ultrasensitive detection of chloramphenicol.

We present a compact optical head design for wide-range and low noise displacement sensing using deep frequency modulation interferometry. The on-axis beam topology is realised in a quasi-monolithic component and relies on cube beamsplitters and beam transmission through perpendicular surfaces to keep angular alignment constant when operating in air or vacuum, which leads to the generation of ghost beams that can limit the phase readout linearity. We investigate the coupling of these beams into the non-linear phase readout scheme of DFMI and demonstrate adjustments of the phase estimation algorithm to reduce this effect. This is done through a combination of balanced detection and the inherent orthogonality of beat signals with different relative time-delays in deep frequency modulation interferometry that is a unique feature not available for heterodyne, quadrature or homodyne interferometry.

The understanding of structural alteration mechanisms due to relative humidity impact on organic supports of paintings is of crucial significance for the preventive conservation strategies in order to ensure the long-term preservation of important cultural identity artworks. The effort in this paper is to simulate Museum realistic relative humidity condition in a climate chamber while monitoring the structural responses through a quantitative interferometric method allowing the quantitative correlation between the physical values of deformation and mass alteration relevant to relative humidity fluctuations.

Three-dimensional transfer functions (3D TFs) are generally assumed to fully describe the transfer behavior of optical topography measuring instruments such as coherence scanning interferometers in the spatial frequency domain. Therefore, 3D TFs are supposed to be independent of the surface under investigation resulting in a clear separation of surface properties and transfer characteristics. In this paper we show that the 3D TF of an interference microscope differs depending on whether the object is specularly reflecting or consists of point scatterers. In addition to the 3D TF of a point scatterer, we will derive an analytical expression for the 3D TF corresponding to specular surfaces and demonstrate this as being most relevant in practical applications of coherence scanning interferometry (CSI). We additionally study the effects of temporal coherence and disclose, that in conventional CSI temporal coherence effects dominate. However, narrowband light sources are advantageous if high spatial frequency components of weak phase objects are to be resolved, whereas for low-frequency phase objects of higher amplitude the temporal coherence is less affecting. Finally, we present an approach that explains the different transfer characteristics of coherence peak and phase detection in CSI signal analysis.

This article described the technology of determining earthquake epicenter with radar remote sensing on the example of Sentinel-1A/B. To determine the epicenter of the earthquake, the Earth's crust displacements were analyzed using radar remote sensing data obtained for the ascending and descending flight orbits. Coordinates of Earthquake epicenters were found according to line-of-sight displacement images via its maximum value. Displacement of the Earth's crust was obtained by processing in the GMTSAR package in the VirtualBox virtual machine of the Linux Ubuntu 16.04 operation system. Two earthquakes that occurred in 2020 were studied to determine the accuracy of finding epicenters using the ascending and descending orbits Sentinel-1A/B. These earthquakes occurred in Western Xizang, China, and Doganyol, Turkey. The maximum deviation from the officially registered epicenter coordinates was 15.38 km for Doganyol and 3.2 km for the Western Xizang earthquake. The negative displacement was 90 mm for Doganyol and 50 mm for Western Xizang.

Interferometry is used in magnetic fusion devices to measure the line-1 averaged electron density. It is based on detecting changes in the refractive index of electromagnetic waves traveling through a plasma. The adequate frequency of these electromagnetic waves depends on several limitations. First the maximum expected peak electronic density must be lower than the cutoff density for that frequency. This means that the waves can still propagate through the plasma when the maximum density is reached. In this sense, IR interferometers operating in the infrared región are themost suitable. With such low wavelengths, mechanical vibrations become an important issue and a complementary interferometer to cancel these vibrations must be used. These arrangements are called two color interferometers. In this paper some measurements that were obtained from the TJ-II double color IR FPGA-based processing system that were never published before are shown and analyzed. The line-averaged electron density is computed in real time (100 μs).

There are some limitations in the null test measurement in the stitching interferometry. In order to meet the null test conditions, the moving distance between the sub-apertures often deviates from the theoretical preset distance, which leads to a position deviation of sub-apertures under measurements. To overcome this problem, an algorithm for data processing is proposed. We used iterative calculation of the deviations between the sub-apertures to adjust their positions, to ensure the local validity of the linear approximation algorithm and realize the exact stitching. A cylindrical lens as an object for experimental examination of the proposed method was taken. The obtained results demonstrate the validity, reliability and feasibility of our iterative stitching algorithm.

Super-resolution technology is important not only in bio-related fields but also in nanotechnology, particularly in the semiconductor industry, where fine patterning is required and super-resolution is essential. However, observing microstructures beyond the diffraction limit proposed by Abbe and Rayleigh is considered impossible because of diffraction in traditional optical microscopy ob-servation techniques. However, in recent years, it has been possible to observe microstructures beyond the Rayleigh criterion by analysing the phase distribution of light. This study investigated the physical reasons why phase analysis makes this new analysis technique possible using simula-tions. The results confirmed that the phase component of the zero-order diffracted light reflected from the microstructure and able to pass through the lens system contained the phase information related to the shape of the measured object. Analysis of this information demonstrates the possi-bility of realising super-resolution based on speckle interferometry.

Sentinel-1 satellite system continuously observes European countries in a relatively high revisit frequency of 6 days per orbital track. Given the Sentinel-1 configuration, most areas in Czechia are observed every 1–2 days by different tracks in a moderate resolution. This is attractive for various types of analyses by various research groups. The starting point for processing is an original data provided by ESA, for interferometry (InSAR) this level is a Single Look Complex (SLC) data. This work represents advantages of storing data augmented to a specifically corrected level of data, SLC-C. The presented database contains Czech nation-wide Sentinel-1 data stored in burst units that have been preprocessed to the state of a consistent well-coregistered dataset of SLC-C. These are resampled SLC data with their phase values reduced by a topographic phase signature, ready for fast interferometric analyses (an interferogram is generated by a complex conjugate between two stored SLC-C files). The data can be used directly into multitemporal interferometry techniques, e.g. Persistent Scatterers (PS) or Small Baseline (SB) techniques applied here. A further development of the nation-wide system utilising SLC-C data would lead into a dynamic state where every new pre-processed burst triggers a processing update to detect unexpected changes from InSAR time series and therefore provide a signal for early warning against a potential dangerous displacement, e.g. a landslide, instability of an engineering structure or a formation of a sinkhole. An update of the processing chain would also allow use of cross-polarised Sentinel-1 data, needed for polarimetric analyses. The current system is running at a national supercomputing centre IT4Innovations in interconnection to the Czech Copernicus Collaborative Ground Segment (CESNET), providing fast on-demand InSAR results over Czech territories. A full nation-wide PS processing using data over Czechia has been performed in 2017, discovering several areas of land deformation. Its downsampled version and basic findings are demonstrated within the article.

Space-borne Synthetic Aperture Radar (SAR) Interferometry (InSAR) is now a key geophysical tool for surface deformation studies. The European Commission’s Sentinel-1 Constellation began acquiring data systematically in late 2014. The data, which are free and open access, have global coverage at moderate resolution with a 6 or 12-day revisit, enabling researchers to investigate large-scale surface deformation systematically through time. However, full exploitation of the potential of Sentinel-1 requires specific processing approaches as well as the efficient use of modern computing and data storage facilities. Here we present LiCSAR, an operational system built for large-scale interferometric processing of Sentinel-1 data. LiCSAR is designed to automatically produce geocoded wrapped and unwrapped interferograms and coherence estimates, for large regions, at 0.001° resolution (WGS-84 system). The products are continuously updated in a frequency depending on prioritised regions (monthly, weekly or live update strategy). The products are open and freely accessible and downloadable through an online portal. We describe the algorithms, processing, and storage solutions implemented in LiCSAR, and show several case studies that use LiCSAR products to measure tectonic and volcanic deformation. We aim to accelerate the uptake of InSAR data by researchers as well as non-expert users by mass producing interferograms and derived products.

The Square Kilometre Array (SKA) will be both the largest radio telescope ever constructed and the largest Big Data project in the known Universe. The first phase of the project will generate on the order of 5 zettabytes of data per year. A critical task for the SKA will be its ability to process data for science, which will need to be conducted by science pipelines. Together with polarization data from the LOFAR Multifrequency Snapshot Sky Survey (MSSS), we have been developing a realistic SKA-like science pipeline that can handle the large data volumes generated by LOFAR at 150 MHz. The pipeline uses task-based parallelism to image, detect sources, and perform Faraday Tomography across the entire LOFAR sky. The project thereby provides a unique opportunity to contribute to the technological development of the SKA telescope, while simultaneously enabling cutting-edge scientific results. In this paper, we provide an update on current efforts to develop a science pipeline that can enable tight constraints on the magnetised large-scale structure of the Universe.

This research aimed to compare the measurements recorded by a traditional PCI technology biometer (Partial Coherence Interferometry) and by a SS-OCT (Swept Source Optical Coherence Tomography) technology machine in preoperative screening of patients with age-related cataract. Optical biometry was performed with the IOLMaster 500 (version 5.5, Carl Zeiss Meditec, Germany) and the ANTERION (Heidelberg Engineering, Germany) in a total sample of 144 eyes, from 80 patients, (37 men and 43 women), with a mean age of 70.54 ± 0.739 years (range: 45-89 years) and the values of the Axial Length (AL), two meridians of the cornea (Kf, Kflat and Ks, Ksteep), astigmatism (Ast) as well as the Anterior Chamber Depth (ACD) were compared with the program IBM SPSS Statistics 27. The IOLMaster500 and ANTERION devices did not have statistically significant differences in terms of axial length and flat corneal meridian Kf, while they differed statistically significantly in terms of steep corneal meridian Ks, astigmatism and anterior chamber depth. This study suggests that a thorough pre-operative check must be performed, sometimes with more than one device, aiming at greater accuracy in the measurements of the ocular biometrics, so that we achieve more successful postoperative outcomes and ultimately more satisfied patients.

Since the 1970s, land subsidence has been developing rapidly in the Beijing Plain, the systematic study of its evolution mechanism is of great significance to the sustainable development of the regional economy. First, based on ENVISAT ASAT and RADARSAT2 data, the land subsidence data in Beijing Plain were obtained using permanent interferometer technology. Second, based on the GIS platform and using fishing net tools, vector data of ground settlement with different resolutions were obtained. Through a series of tests, a scale of 960 metres was selected as the research unit, and the subsidence rate of the grid was obtained from 2004 to 2015. Finally, based on the Mann-Kendall mutation test method, a trend analysis of land subsidence changes in various grids was carried out. The results showed that single-year mutation mainly distributed in the middle and lower parts of the Yongding River alluvial fan and the Chaobai River alluvial fan, mainly occurring in 2015, 2005 and 2013, respectively. The upper and middle alluvial fan of the Chaobai River, the vicinity of the emergency water source and the edge velocity of the groundwater funnel have undergone several sudden changes. Combined with hydrogeology, basic geological conditions and the impact of the South-to-North Water transfer project, we analysed the causes of the mutations in the grid. The research results can provide a basis for the study and prevention of land subsidence in this area and help to further explore the trend characteristics of land subsidence in this area.

In the Aharonov-Bohm setup, a double-slit experiment, coherent beams of electrons passing through two slits form an interference pattern on the observing screen. However, when a long but thin solenoid of current is introduced behind the slits between the two electron beams, an extra phase difference between them appears, as shown by a shift in the interference pattern. This happens even though there is no magnetic field outside the solenoid, at the location of the beams. This is known as Aharonov-Bohm effect, though the idea was mooted apparently a decade earlier, and the effect sometimes is called Ehrenberg-Siday-Aharonov-Bohm effect. This mysterious effect, purportedly arises owing to an electromagnetic momentum, attributed to the presence at the location of either beam, a vector potential due to the solenoid of current even when there exists no magnetic field outside the solenoid. The first experimental confirmation came soon and It has since been amply verified using clever experimental setups, leaving hardly any doubts that the observed effect is real. However, on the theoretical side the picture is not so clear and a satisfactory physical explanation of the existence of momentum, at least under the aegis of classical electromagnetism, is still missing since inception of the idea more than half a century back. It has remained a puzzle, how just potential, thought to be a mere mathematical tools for calculating electromagnetic field, can give rise to an electromagnetic momentum in a system, in lieu of field itself. We here show that a subtle momentum can be seen to lie in the product of the drift velocities of the current carrying charges and the mass equivalent of their non-localized potential energies in the electric field of the interfering electrons, which manifests, from a classical point of view, a linear momentum in the system. It is this hard-to-pinpoint, additional momentum, reflected through an extra phase difference between the interfering beams of electrons, which exhibits from a classical physics perspective, the presence of an elusive, long sought-after electromagnetic momentum in the system.

In this study we fabricate gold nanocomposites and model their optical properties. The nanocomposites are either homogeneous films or gratings containing gold nanoparticles embedded in a polymer matrix. The samples are fabricated using a recently developed technique making use of laser interferometry. The gratings present original plasmon-enhanced diffraction properties. In this work, we develop a new approach to model the optical properties of our composites. We combine the extended Maxwell-Garnett model of effective media with the Rigorous Coupled Wave Analysis (RCWA) method and compute both the absorption spectra and the diffraction efficiency spectra of the gratings. We show that such a semi-analytical approach allows us to reproduce the original plasmonic features of the composites and can give us entails about their inner structure. Such approach could be a simple and efficient tool to study complex micro-structured system based on plasmonic components, such as metamaterials.

Bridge load testing is crucial in evaluating bridge load-carrying capacity and construction quality. However, conventional techniques have many limitations such as the need for direct contact and low acquisition frequency. This study provides a comprehensive examination of the static and dynamic load tests of a multi-span cable-stayed bridge utilizing a ground-based radar inter-ferometer (GB-radar). The case study was conducted at the Fifth Nanjing Yangtze River Bridge (FNYRB), which is recognized as the world's first lightweight steel-concrete composite cable-stayed bridge, with two spans measuring 600 m. To enhance measurement accuracy, a method was proposed to detect and recover radar phase jumps caused by vehicle motion. Furthermore, precise geometry projection was employed to acquire vertical displacements from GB-radar which were taken along the line-of-sight (LOS) direction. Moreover, during the static load test, a continuous deformation was observed with a maximum pace of 0.31 mm/min, indicating a post-construction settlement caused by soft soil consolidation. This case study highlights the high sampling frequency, high measurement accuracy, and exceptional weatherproof ability of GB-radar, thereby demonstrating its potential to be an alternative to the structural health monitoring (SHM) system.

Two algorithms of data processing are proposed to shorten the unmeasurable dead-zone close to the zero-position of measurement, i.e., the minimum working distance of a dispersive interferometer using optical frequency comb, which is a critical issue in millimeter-order short-range absolute distance measurement. After demonstrating the limitation of the conventional data processing algorithm, the principles of the proposed algorithms, namely the spectral fringe algorithm, and the combined algorithm that combines the spectral fringe algorithm with the excess fraction method, are presented, together with simulation results for demonstrating the possibility of the proposed algorithms for shortening the dead-zone with a high accuracy. An experimental setup of dispersive interferometer is also constructed for implementing the proposed data processing algorithms over spectral interference signals. Experimental results demonstrate that the dead-zone by the proposed algorithms can be as small as half of that by the conventional algorithm while the measurement accuracy can be further improved with the combined algorithm.

Seismic travel time tomography using surface waves is an effective tool for three-dimensional crustal imaging. Historically, these surface waves are the result of active seismic sources or earthquakes. More recently, however, also surface waves retrieved through the application of seismic interferometry are exploited. Conventionally, two-step inversion algorithms are employed to solve the tomographic inverse problem. That is, a first inversion results in frequency-dependent, two-dimensional maps of phase velocity, which then serve as input for a series of independent, one-dimensional frequency-to-depth inversions. As such, a two-dimensional grid of localized depth-dependent velocity profiles are obtained. Stitching these separate profiles together subsequently yields a three-dimensional velocity model. Relatively recently, a one-step three-dimensional non-linear tomographic algorithm has been proposed. The algorithm is rooted in a Bayesian framework using Markov chains with reversible jumps, and is referred to as transdimensional tomography. Specifically, the three-dimensional velocity field is parameterized by means of a polyhedral Voronoi tessellation. In this study, we investigate the potential of this algorithm for the purpose of recovering the three-dimensional surface-wave-velocity structure from ambient noise recorded on and around the Reykjanes Peninsula, southwest Iceland. To that end, we design a number of synthetic tests that take into account the station configuration of the Reykjanes seismic network. We find that the algorithm is able to recover the 3D velocity structure at various scales in areas where station density is high. In addition, we find that the standard deviation on the recovered velocities is low in those regions. At the same time, the velocity structure is less well recovered in parts of the peninsula sampled by fewer stations. This implies that the algorithm successfully adapts model resolution to the density of rays. Also, it adapts model resolution to the amount of noise on the travel times. Because the algorithm is computationally demanding, we modify the algorithm such that computational costs are reduced while sufficiently preserving non-linearity. We conclude that the algorithm can now be applied adequately to travel times extracted from (time-averaged) station-station cross correlations by the Reykjanes seismic network.

We scrutinize the reliability of multilooked interferograms for deformation analysis. Designing a simple approach in the evaluation of the accuracy of the estimated deformation signals, we reveal a prominent bias in the deformation velocity maps. The bias is the result of propagation of small phase error of multilooked interferograms through the time series and can sum up to 6.5 mm/yr in case of using the error prone short temporal baseline interferograms. We further discuss the role of the phase estimation algorithms in reduction of the bias and put recommend a unified intermediate InSAR product for achieving high-precision deformation monitoring.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

Interferometry Synthetic Aperture Radar (InSAR) is an advanced remote sensing technique for studying the earth's surface topography and deformations. It is used to generate high-quality Digital Elevation Models (DEMs). DEMs are a crucial and primary input to various topographical quantification and modelling applications. The quality of input DEMs can be further improved using fusion methods, which combine multi-sensor or multi-temporal datasets intelligently to retrieve the best information amongst the input data. This research study is based on developing a Neural Network based fusion approach for improving InSAR based DEMs in plain and hilly terrains. The study areas comprise of relatively plain terrain from Ghaziabad and hilly terrain of Dehradun and their surrounding regions. The training dataset consists of DEM elevations and derived topographic attributes like slope, aspect, topographic position index (TPI), terrain ruggedness index (TRI), and vector roughness measure (VRM) in different land use land cover classes of the study areas. The spaceborne altimetry ICESat-2 ATL08 photon data is used as a reference elevation. A Feed Forward Neural Network with backpropagation algorithm is trained based on the prepared training samples. The trained model produces fused DEMs by learning the relationship between the input and target samples. This is used to predict elevations in the test areas. The accuracy of results from the models are assessed with TanDEM-X 90 m DEM. The fused DEMs show significant improvement in terms of RMSE over the input DEMs with improvement factor of 94.65 % in plain area and 82.62 % in hilly area. The study concludes that the ANN with its universal approximation property is able to significantly improve the fused DEM.

A microwave-photonics method has been developed for measuring distributed acoustic signals. This method uses microwave-modulated low coherence light as a probe to interrogate distributed in-fiber interferometers, which are used to measure acoustic-induced strain. By sweeping the microwave frequency at a constant rate, the acoustic signals are encoded into the complex microwave spectrum. The microwave spectrum is transformed into the joint time-frequency domain and further processed to obtain the distributed acoustic signals. The method is first evaluated using an intrinsic Fabry Perot interferometer (IFPI). Acoustic signals of frequency up to 15.6 kHz were detected. The method was further demonstrated using an array of in-fiber weak reflectors and an external Michelson interferometer. Two piezo-ceramic cylinders (PCCs) driven at frequencies of 1700 Hz and 3430 Hz were used as acoustic sources. The experiment results show that the sensing system can locate multiple acoustic sources. The system resolves 20 nε when the spatial resolution is 5 cm. The recovered acoustic signals match the excitation signals in frequency, amplitude, and phase, indicating an excellent potential for distributed acoustic sensing (DAS).

Space-based Interferometric Synthetic Aperture Radar (InSAR) applications have been widely used to monitor the cryosphere over past decades. Because of temporal decorrelation, interferometric coherence often severely degrades on fast moving glaciers. In addition, higher sensitivity ambiguity occurs in large baseline configurations, which are needed for extracting topographic information over low relief areas such as the surface of a glacier. TerraSAR-X add-on for Digital Elevation Measurement (TanDEM-X) observations, which overcome the temporal decorrelation because of their simultaneous measurements by two satellite constellations, have used a short baseline sufficient for generation of excellent digital elevation models in most locations around the world. However, it remains difficult to estimate detailed topographic characteristics over low slope glacier surfaces because of the relatively less sensitive height ambiguity from the small baselines. In this study, we used the TanDEM-X pursuit monostatic mode with large baseline formation following a scientific phase timeline to develop highly sensitive topographic elevation models of the Petermann Glacier of Northwest Greenland. As expected, coherent interferometric phases (> 0.8) were well maintained over the glaciers despite their fast movement thanks to the nearly simultaneous TanDEM‐X measurements. The height ambiguity, which defined as the altitude difference correspondent to phase change of flattened interferogram, of the dataset was 10.63 m, which is favorable for extracting topography in a low relief region. We validated the TanDEM‐X derived glacial topography by comparing it to the SAR/Interferometric radar altimeter observations acquired by CryoSat‐2 and the IceBridge Airborne Topographic Mapper laser altimeter measurements. Both observations showed very good correlation within a few meters of the offsets (‐12.5 – ‐3.1 m) with respect to the derived glacial topography. Because of highly sensitive ambiguity, we could successfully extract detailed geomorphological features on the glaciers. Routine TanDEM-X observations will be very useful to better understand the dynamics of glacial movements and topographic change.

Shot peening has become a well-established technique for the introduction of beneficial compressive Residual Stresses (RS) into the near-surface layers of metallic materials for the purpose of preventing or suppressing fatigue crack nucleation and growth. Ti-alloys are widely used to fabricate compressor blades of aeroengines. Titanium blades that may be susceptible to different modes of damage under cyclic loading (high cycle fatigue, fretting fatigue) are often subjected to shot peening to extend their safe operating time. The control and monitoring of residual stresses in titanium blades is of great importance to assure the safety of aeroengines. The techniques for residual stress evaluation include mechanical methods (material removal) as well as physical methods such as X-ray diffraction. Perhaps the most common and practically accessible form of the latter is the method. Conventional laboratory X-ray diffractometers typically probe samples to the depths up to ~20 µm that correspond to 1x...5x the average grain size for typical metals and alloys. The limitations of the method have been identified and reviewed in the literature, motivating the use of other semi-destructive approaches to evaluate the residual stresses in deeper layers and at more sharply defined locations. In the present report we present a case study of the comparison between non-destructive and semi-destructive evaluation techniques, namely the X-ray diffraction method against the mechanical and FIB-DIC ring-core drilling applied to the samples of VT6 (Russian designation of Ti-6Al-4V) titanium alloy after shot peening with 1 mm steel balls. Mechanical drilling of circular holes of ~2 mm diameter with laser speckle interferometry monitoring of strains gives a rough spatial resolution of a few millimeters, while the Korsunsky FIB-DIC method of Ga-ion beam micro-ring core milling within FIB-SEM with Digital Image Correlation (DIC) deformation analysis delivers spatial resolution down to a few micrometers. Good agreement has been found between the X-ray and FIB-DIC estimates of RS variation profiles as a function of depth in shot peened titanium alloy samples. Some advances in the FIB-DIC method are presented and discussed in terms of the acceleration of data acquisition and interpretation.

SLM Additive Manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabrication of different structures in aerospace industry. The importance of the evaluation of residual stresses that arise as a result of complex 3D-printing process thermal history is widely discussed in literature, but systematic assessment remains lacking for their magnitude, spatial distribution, and comparative analysis of different evaluation techniques. In this study we report the results of a systematic study of residual stresses in a 3D-printed double tower shaped samples using several approaches: the contour method, blind hole drilling laser speckle interferometry, X-ray diffraction, and Xe pFIB-DIC micro-ring-core milling analysis. We show that a high level of tensile and compressive residual stresses is inherited from SLM 3D-printing and retained for longer than 6 months. The stresses vary over a significant proportion of the material yield stress. All residual stress evaluation techniques considered returned comparable values of residual stresses even regardless of dramatically different dimensional scales from millimeters for the Contour Method down, laser speckle interferometry and XRD and down to small fractions of a mm (70 μm) for Xe pFIB-DIC ring-core drilling. The use of residual stress evaluation is discussed in the context of optimizing the printing strategy to enhance the mechanical performance and long-term durability.

Background: Inadequate meibomian glands (MGs) secretion can lead to dry eye signs and symptoms. Tear film lipid layer (TFLL) secreted by MGs protects and prevents rapid evaporation of tear film. Our purpose was to assess TFLL alteration and function in patients with evaporative dry eye (EDE) using tear interferometry after optimal pulse light technology (OPT) intense pulsed light (IPL). Methods: This prospective randomized examiner-masked sham- controlled study included 86 participants (142 eyes) with DED. IPL or sham procedure was performed on day 0, 21, and 42. Ocular Surface Disease Index (OSDI), non-invasive breakup time (NITBUT), interferometric fringe pattern determined TFLL quality, fluorescein staining (FS), and meibum gland (MG) were assessed at day 0, 21, 42 and 3-month. Results: At 3-month, TFLL, NITBUT, MG drop-out, MG quality, MG expressibility, FS and OSDI improved significantly (P<0.05) in the IPL group, while the sham group had no significant improvements. All DE parameters significantly correlated with the improvement in TFLL following IPL treatment. Additionally, artificial tears usage was significantly less in the IPL group from D-42 onwards. Conclusion: IPL treatment demonstrated the ability to improve TFLL quality and clinically reduced sign and symptoms of DED thereby reducing the frequency of artificial tears usage.

From 1964 to the early 1970s, Orson Anderson led a research program at the Lamont Geological Observatory in the newly-emerging field of “mineral physics”. In collaboration with colleagues Edward Schreiber and Naohiro Soga, Orson exploited the techniques of physical acoustics to study the behavior of the sound velocities of minerals at elevated pressures and temperatures. This research program also included semi-empirical studies of relationships between the bulk modulus and the molar volume of solids and the use of lattice dynamics to calculate the elastic moduli of cubic structures as a function of pressure to predict instabilities, as well as theoretical investigations of the Lagrangian vs. Eulerian formulations of finite strain equations of state.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

It is widely believed that the dramatic transformation of the spherical outflows of AGB stars into the extreme aspherical geometries seen during the planetary nebula (PN) phase is linked to binarity and driven by the associated production of fast jets and central disks/torii. The key to understanding the engines that produce these jets and the jet-shaping mechanisms lies in the study of objects in transition between the AGB and PN phases. I discuss the results of our recent studies with high-angular-resolution (with ALMA & HST) and at high-energies (with GALEX, XMM-Newton & Chandra) of several such objects, which reveal new details of close binary interactions and high-speed outflows. These include two PPNe (the Boomerang Nebula and IRAS16342-3814), and the late carbon star, V Hya. The Boomerang is notable for a massive, high-speed outflow that has cooled below the microwave background temperature, making it the coldest object in the Universe. IRAS16342 is the prime example of the class of water-fountain PPNe (very young PPNe with high-velocity H₂O masers) and shows the signature of a precessing jet. V Hya ejects high-speed bullets every 8.5 years associated with the periastron passage of a companion in an eccentric orbit. I discuss our work on AGB stars with strongly-variable high-energy (FUV, X-ray) emission, suggesting that these objects are in the early stages of binary interactions that result in the formation of accretion disks and jets.

Slope failures pose a substantial threat to mining activity due to their destructive potential and high probability of occurrence on steep slopes close to limit equilibrium conditions, often found both in open pits and in waste and tailing disposal facilities. The development of slope monitoring and modeling programs usually entails the exploitation of in situ and remote sensing data together with the application of numerical modeling, and it plays an important role in the definition of prevention and mitigation measures aimed at minimizing the impact of slope failures in mining areas. Here we present a new methodology combining satellite radar interferometry and 2D finite element modeling for slope stability analysis at a regional scale, applied within slope unit polygons. We studied a former mining area in southeast Spain, and the method proved useful in detecting and characterizing a considerably large number of unstable slopes. Out of 1,959 slope units used for the spatial analysis of the radar interferometry data, 43 were unstable, with varying values of safety factor and landslide size. Out of the 43 active slope units, 21 exhibited line of sight velocities greater than the maximum error obtained through the validation analysis (2.5 cm/year). Eventually, this work discusses the possibility of using the results of the proposed approach to devise a proxy for landslide hazard. The proposed methodology can help to provide non-expert final users with intelligible, clear and easily comparable information to analyze slope instabilities in different settings, not limited to mining areas.

This research aims to estimate the micro-motion (m-m) of ships. The problem of motion and m-m detection of targets is usually solved using synthetic aperture radar (SAR) along-track interferometry (ATI) which is observed employing two radars spatially distanced by a baseline extended in the azimuth direction. This paper is proposing a new approach where the m-m estimation of ships, occupying thousands of pixels, is measured processing the information given by sub-pixel tracking generated during the coregistration process of several re-synthesized time-domain and overlapped sub-apertures. The SAR products are generated splitting the raw data, according to a small-temporal baseline strategy, observed by one single wide-band staring spotlight (ST) SAR image. The predominant vibrational modes of different ships are estimated and results are promising to extend this application in performing surveillance also of land-based industries activities. Experiments are performed processing one ST SAR image observed by the COSMO-SkyMed satellite system.