Cholangiocellular carcinoma (CCA) is the second most common primary liver cancer, with increasing incidence worldwide and inadequate therapeutic options. Intra- and extrahepatic bile ducts have distinctly different embryonic origins and developmental behavior, and accordingly intra- and extrahepatic CCAs (ICC vs. ECC) are molecularly different. A promising strategy in oncotherapy is targeted therapy, targeting proteins that regulate cell survival and proliferation; such as the MAPK/ERK and PI3K/AKT/mTOR signaling pathways. Inhibitors of these pathways have been tested previously in CCA cell lines. However, these cell lines could not be clearly assigned to ICC or ECC, and results indicated apoptosis induction by targeted therapeutics. We tested targeted therapeutics (selumetinib, MK2206) in three defined ICC cell lines (HuH28, RBE, SSP25). We observed cooperative effects of dual inhibition of the two pathways, in accordance with inhibition of phospho-AKT and phospho-ERK1/2 expression. Proliferation was blocked more effectively with dual inhibition than with each single inhibition, but cell numbers did not drop below baseline. Accordingly, we observed G1-phase arrest, but not apoptosis (cleaved caspase-3, AIFM1 regulation, subG1-phase) or necroptosis (phospho-MLKL). We conclude that dual inhibition of MAPK/ERK and PI3K/AKT/mTOR pathways is highly effective to block proliferation of ICC cell lines, but therapy must certainly be supplemented with standard therapies.

This study investigates the impacts of climate change policies on businesses across various sectors, aiming to understand how these regulations affect operational, financial, and strategic aspects of business management. Utilizing a mixed-methods approach, data was collected from 500 businesses through surveys and interviews, encompassing a wide range of industries, sizes, and geographic locations. The findings reveal a complex landscape where 30% of businesses report positive impacts, primarily in the renewable energy and technology sectors, citing increased demand for green products and improvements in energy efficiency. Conversely, 45% of businesses, especially from manufacturing and agriculture, experience negative impacts, including increased operational costs and regulatory compliance challenges. Notwithstanding, a significant majority of businesses are committed to enhancing their sustainability practices, viewing climate change policies as an opportunity for innovation and long-term growth. The study highlights the nuanced effects of climate change policies, emphasizing the need for sector-specific support measures to alleviate financial and operational burdens on negatively impacted businesses. Moreover, it points to a broader shift towards sustainability within the business community, suggesting that climate policies, despite their varied impacts, are driving significant changes in business strategies towards environmental stewardship.

This paper presents an in-depth study of the stress wave behavior propagating in a Rayleigh–Love rod with a sudden cross-sectional area change. The analytical solutions of stress waves are derived for the reflection and transmission propagation behavior at the interface of the cross-sectional area change in the rod, considering inertia and Poisson’s effects. Examples solved by the finite element method are provided to verify the correctness of the analytical results. In addition to the forward analysis of Rayleigh–Love wave propagation in rods impacted by a striker rod, a nondestructive testing method is proposed to conduct the defect assessment in the rod type of the structure component with a sudden cross-sectional area change within a cover medium by using the measured signals at the measurable zone of the rod to be inspected.

Materials based on platinum metals with very good catalytic activity were tested in the reduction of p–nitrophenol (pNP) to p–aminophenol (pAP). The majority of presented catalytic materials are based on the adsorption of p–nitrophenol on the surface of the catalyst simultaneously with molecular hydrogen, coming from sodium borohydride in an aqueous medium, which reduces it. In the present paper, a catalytic material based on osmium dispersed in n–decanol or n–dodecanol is presented, which also works as an emulsion membrane, for the absorption of p–nitrophenol and molecular hydrogen at the n–alcohol aqueous solution interface. The hydrogenation of p–nitrophenol is carried out in a reaction and separation column in which the acid receiving phase emulsion is dispersed in the osmium nanodispersion, in n–alcohols. This emulsion circulates from the base of the column to its upper part in co-current or counter-current with the source phase consisting of p–nitrophenol and sodium borohydride. Experiments show that the circulation of counter-current phases is superior to that in co-current, and the emulsion based on n–decanol is more efficient than the one based on n–dodecanol. The increase in the pH difference between the source and receiving phases leads to the increase in the conversion of p–nitrophenol to p–aminophenol. The efficiency of separation of the reaction product in the receiving phase is lower than the conversion at the same operating time. The apparent catalytic rate constant (kapp) of the new catalytic material based on the emulsion membrane with nanodispersion of osmium nanoparticles (0.1×10−3 for n–dodecanol and 0.9×10−3 for n-decanol) is lower by an order of magnitude compared to those based on adsorption on catalysts from platinum metal group. The advantage of the tested membrane catalytic material is that it extracts p–aminophenol in the acid receiving phase. The paper proposes a mechanism of the studied reduction system.

Surface–subsurface soil-rock modeling is crucial for infrastructure design and groundwater yield optimization, especially in the complex crystalline basement terrains of Penang Island, Malaysia. This study conducted large-scale characterization of soil-rock profiles using ERT, SRT, rock quality designation, and soil penetration test (SPT N-values) data, optimized through regression modeling. The approach effectively identified soil-rock structures and their suitability to prevent structural failures and enhance groundwater productivity. Correlations between borehole lithologic logs and velocity–resistivity models revealed distinct soil compositions across the study area. The results highlighted thick, saturated, and loose silty to sandy bodies in the eastern to northern sections, contrasting with sandy compositions and penetrative fractures in the southern part. The study also found good correlations between rock mass quality and N-values for different soil types. Depths of intra-bedrock weathered/fractured units varied between 12 and >35 m. This has significant implications for determining optimal foundation depths in the study area. Groundwater productivity was associated with intra-bedrock planes of weakness at depths exceeding 40 m. Overall, this study developed empirical relations between geophysical and geotechnical parameters for wet tropical granitic terrains, filling critical gaps in understanding subsurface characteristics.

A linear stability analysis of the parallel uniform flow in a horizontal channel with open upper boundary is carried out. The lower boundary is considered as an impermeable isothermal wall, while the open upper boundary is subject to a uniform heat flux and it is exposed to an external horizontal fluid stream driving the flow. An eigenvalue problem is obtained for the two-dimensional transverse modes of perturbation. The study of the analytical dispersion relation leads to the conditions for the onset of convective instability as well as to the determination of the parametric threshold for the transition to absolute instability. The results are generalised to the case of three-dimensional perturbations.

We show how the Poincar\'e--Riemann--Hilbert boundary-value problem enables us to construct effective estimates of the potential in the Schr\"odinger equation. The apparatus of the three-dimensional inverse problem of quantum scattering theory is developed for this. It is shown that the unitary scattering operator can be studied as a solution of the Poincar\'e--Riemann--Hilbert boundary-value problem. This allows us to go on to study the potential in the Schr\"odinger equation

Quantum Rayleigh scattering of single photons rules out coincident detections of the originally entangled, paired photons Correlations between independent states of qubits can easily outperform those calculated with entangled photons. The quantum joint probability for a Bell state can be factorized enabling a local detection of the alleged quantum nonlocality, if it existed.

Tropical cyclones have long been known to be powered by turbulent enthalpy fluxes from the ocean surface and retarded by turbulent momentum fluxes into the surface. Here were review evidence that the development and structure of these storms are also partially controlled by turbulence in the outflow near the storm top. Finally, we present new research that shows that tropical cyclone-like, low-aspect-ratio vortices are most likely in systems in which the bottom heat flux is controlled by mechanical turbulence and the top boundary is insulating.

SStatistical characteristics of the wind speed in Samaria region of Israel have been analyzed by processing 11 years of wind data provided by the Israeli Meteorological Service, recorded at 10 m height above the ground. The cumulative mean wind speed at measurement height was shown to be 4.53 m/s with standard deviation of 2.32 m/s. Prevailing wind direction is shown to be char-acterized by cumulative mean azimuth of 226° with standard deviation of 79.76°. The results were extrapolated to 70-meter height in order to estimate wind characteristics at hub height of a me-dium-scale wind turbine. Moreover, Weibull distribution parameters were calculated annually, monthly and seasonally, demonstrating a good match with histogram-based statistical repre-sentations. Shape parameter of the Weibull distribution was shown to reside within a narrow range of 1.93 to 2.15, allowing us to assume a Rayleigh distribution, thus simplifying wind tur-bines energy yield calculations. The novelty of the current paper is related to gathering wind statistics for a certain area (Samaria) we are not aware of any published statistics regarding wind velocity and direction in this area. The data may be interesting for potential regional wind energy development in which the obtained Weibull distribution can be used in calculations of expected power generation of particular turbines with known power dependence on velocity. We also point out that the fact that realistic wind velocity statistics is well described by an analytic formula (Weibull distribution) is not trivial, and in fact the fit may have been poor.

The purpose of this paper was to examine the differences in using agricultural entrepreneurship support and in how it relates to characteristics such as the agrarian structure, socioeconomic de-velopment level and land use across the Polish territory. The analyses were carried out at district (poviat) level which is an intermediate administrative unit. The study found that the decisions on co-financing the measures dedicated to non-agricultural economic activity heavily depend on the agrarian structure. The highest levels of activity were witnessed in districts where the agrar-ian structure is particularly fragmented.

A substantial amount of phosphorus (P) in soil is not readily available for plant uptake. Certain species may enhance P availability from poorly soluble P forms. This research aimed to compare the P solubilization capacity of the soil of two Lupine species, L. albus, and L. angustifolius, with a control crop of oats (Avena strigosa L.). Plants were planted in pots in four soils with varying texture, organic matter content, acidity, and P availability. Phosphorus solubilization capacity was assessed on variations of P availability (PBray1) at four points in time, comparing soils with lupine to oat-containing soils and their baseline values. At harvest, measurements of plant shoot biomass included their shoot dry weight and some nutrient concentrations such as P, nitrogen (N), manganese (Mn), and lupine nitrogen fixation. Compared to soils containing oats, lupine soils significantly increased PBray1 concentrations; increments ranged from 0.9 to 5.4 mg kg-1, depending on species, sampling time, and soil type. Lupine-induced soil acidification did not fully explain this P increase., As a proxy measurement of organic acid exudation, Manganese concentration was high in both lupine species' shoot biomass; however, these legumes had divergent Mn accumulation responses to soil acidity and P availability. Nitrogen fixed quantity varied with Lupine species (105-240 mg pot-1) and soil type (60-240 mg pot-1). Lupinus albus had a higher ability to mobilize non-labile P and provide N through biological N fixation (BNF), positioning it as a suitable crop for diversifying Uruguay's agricultural crop rotation systems.

In this paper, we propose and demonstrate a network analysis optical frequency domain reflectometer (NA-OFDR) for distributed temperature measurements at high spatial (down to 3 cm) and temperature resolution. The system makes use of a frequency-stepped, continuous-wave (cw) laser, whose output light is modulated using a vector network analyzer. The latter is also used to demodulate the amplitude of the beat signal obtained by coherently mixing the Rayleigh backscattered light with a local oscillator. The system is capable of high measurand resolution (50 mK at 3-cm spatial resolution), thanks to the high sensitivity of coherent Rayleigh scattering to temperature. Furthermore, compared to the conventional optical-frequency domain reflectometry (OFDR), the proposed system does not rely on the use of a tunable laser, therefore it is less prone to limitations related to the laser coherence or sweep nonlinearity. Two configurations are analyzed, both numerically and experimentally, based on either a double sideband or single sideband modulated probe light. The results confirm the validity of the proposed approach.

The locality condition of probabilities underpinning the derivation of Bell inequalities can be violated classically. The wave function collapse results in the factorization of quantum probabilities. It is possible to differentiate, locally, between ensemble probabilities of single detections with and without wave function collapse for the alleged quantum nonlocality. The theoretical concept of photonic quantum nonlocality cannot be implemented physically because of the quantum Rayleigh scattering of single photons. A distinction needs to be made between the correlation of individual, single measurements of pure states and the correlation of the ensemble states of the mixed states. The correlation operator of Pauli vector operators delivers the same probabilities of correlated detections of photons for both independent and multi-photon states as for ‘entangled’ states of photons. As single-photon sources are not needed, the design and implementation of quantum computing operations and other devices will be significantly streamlined.

A physical scrutiny of experimental results published in Physical Review Letters (December 2015, M. Giustina, et al., Phys. Rev. Lett. 115, 250401, and L. K. Shalm et al., Phys. Rev. Lett. 115, 250402) is undertaken. These articles reported that measured outcomes were fitted with quantum states possessing a dominant component of non-entangled photons, thereby contradicting their own claim of quantum nonlocality. With probabilities of photon detections lower than 0.1 %, the alleged quantum nonlocality cannot be classified as a resource for developing quantum computing devices, despite recent publicity. Experimental evidence of a feasible process for quantum-strong correlations has been identified (M. Iannuzzi, et al., Phys. Lett. A, 384 (9), 126200, 2020) in terms of correlations between independent and multi-photon states evaluated as Stokes vectors on the Poincaré sphere. As single-photon sources are not needed, the design and implementation of quantum computing operations will be significantly streamlined.

The purpose of this paper is to simulate a two-dimensional Rayleigh-Taylor instability problem using the classical method of Finite Element analysis of a multiphase model using ANSYS FLUENT 19.2. The governing equations consist of a system of coupled nonlinear partial differential equations for conservation of mass, momentum and phase transport equations. The study focuses on the transient state simulation of Rayleigh Taylor waves and subsequent turbulent mixing in the two phases incorporated in the model. The Rayleigh Taylor instability is an instability of an interface between two fluids of different densities which occurs when the lighter fluid is pushing the heavier fluid in a gravitational field. The problem was governed by the Navier-Stokes and Cahn-Hilliard equations in a primitive variable formulation. The Cahn- Hilliard equations were used to capture the interface between two fluids systems. The objective of this article is to perform grid dependency test on Rayleigh Taylor Instability for 2 different mesh size and compare the results for the variation in Atwood Number. The results were validated with the observations from previous published literatures.

Despite multiple classical outcomes arising from the quantum Rayleigh conversions of photons underlying the propagation of optical waves through dielectric media and the ensuing light-matter interactions, this quantum process has been largely ignored. Several of its outcomes are considered in this article from a physical perspective, e.g., inter-quadrature coupling of photons, phase-dependent amplification in optical directional couplers and related polarization rotation, phase-shifting of weak signals in the optically linear regime, location-dependent coupling coefficient for refractive index gratings, etc. A correct identification of these effects will enable useful design and operation of integrated photonic functional devices.

The interpretation of published experimental results intended to prove the existence of a quantum phenomenon of non-locality involving photonic entangled states did not take into consideration the existence of the quantum Rayleigh conversion of photons in dielectric media. This phenomenon leads to the existence of high levels of correlations between two independent photonic and linearly polarized quantum states generated after the entangled photons have been absorbed through the quantum Rayleigh conversion. Both pure and mixed individual states of polarization result in expressions normally associated with entangled photonic states, providing support for the view that the physical reality of quantum non-locality is highly questionable.

Understanding how humans perceive animals is important for biodiversity conservation, however, only a few studies about this issue were carried out in South America. We selected two Brazilian cities to assess people’s perceptions of birds: Bauru (São Paulo, Brazil) and Belo Horizonte (Minas Gerais, Brazil). From the bird data we gathered, we developed a questionnaire and applied it between September 2020 and June 2021. The data obtained were analyzed by simple counts, Likert scale, and percentages. Also, open questions were placed on the Free Word Cloud Generator website. Our study confirmed that most respondents are aware of the importance of birds to ecological balance and that respondents had a generally positive attitude towards most of the bird species. However, they disliked exotic species such as the Domestic Dove and the House Sparrow, which are associated with disease, dirt, and disgust. Respondents also underestimated the number of birds that can live in urban areas and the song of birds is still a sense less explored and perceived by people. The concept of environmental perception seeks to cover aspects and understanding these human–biodiversity relationships is essential to successfully guide public policies, urban planning interventions, and environmental education activities.

The first hyperpolarizability of graphene quantum dots (GQDs) suspended in water was determined using the hyper-Rayleigh scattering (HRS) technique. To the best of our knowledge, this is the first application of the HRS technique to characterize GQDs. Two commercial GQDs (Acqua-Cyan and Acqua-Green) with different compositions were studied. The HRS experiments were performed with an excitation laser at 1064 nm. The measured hyperpolarizabilities were (1.0±0.1) × 10^(-27) esu and (0.9±0.1) × 10^(-27) esu for Acqua-Cyan and Acqua-Green, respectively. The results were used to estimate the hyperpolarizability per nanosheet obtained by assuming that each GQDs has five nanosheets with 0.3 nm thickness. The two-level model, used to calculate the static hyperpolarizability per nanosheet, provides the values of (2.4±0.1) × 10^(-28) esu (Acqua-Cyan) and (0.5±0.1) × 10^(-28) esu (Aqua-Green). The origin of the nonlinearity is discussed on the basis of polarized resolved HRS experiments, and an electric quadrupolar behavior with a strong dependence on surface effects is found. The nontoxic characteristics and order of magnitude indicate that these GQDs may be useful for biological microscopy imaging.

The paper reports an analytical study of two problems of Rayleigh-Bénard convection(RBC): one in a Newtonian liquid occupying an axi-symmetric cylindrical enclosure(CE) and second in a two-dimensional rectangular enclosure(RE). Linear stability analysis is employed to obtain information on the onset of convection in terms of a critical Rayleigh number, Ra, as a function of the aspect ratio, Ro. The nature and the flow structures of the convective cells, at the onset of convection, are predicted theoretically by plotting the streamlines for different values of Ro. Not so shallow(Ro<1 or Ro≪1), and very shallow enclosures(Ro≫1) are considered. Concepts of cell-width and the wave number are respectively used in these two types of enclosures. An explicit analytical expression for the number of cells as a function of Ro is obtained theoretically. Exact prediction of the critical value of Ra, viz., Rac, as a function of Ro is also made. These are new findings in the case of both CE and RE. The fundamental differences between the problems of CE and RE are also highlighted.

The onset of the thermal instability is investigated in a porous channel with plane parallel boundaries saturated by a non–Newtonian shear–thinning fluid and subject to a horizontal throughflow. The Ellis model is adopted to describe the fluid rheology. Both horizontal boundaries are assumed to be impermeable. A uniform heat flux is supplied through the lower boundary, while the upper boundary is kept at a uniform temperature. Such an asymmetric setup of the thermal boundary conditions is analysed via a numerical solution of the linear stability eigenvalue problem. The linear stability analysis is developed for three–dimensional normal modes of perturbation showing that the transverse modes are the most unstable. The destabilising effect of the non-Newtonian shear–thinning character of the fluid is also demonstrated as compared to the behaviour displayed, for the same flow configuration, by a Newtonian fluid.

Tuning nonlinearity of the laser is the main source which will deteriorate the spatial resolution in optical frequency domain reflectometry system. We develop methods for tuning nonlinearity correction in the OFDR system from the aspects of data acquisition and also the posting-processing. A zero-crossing detection scheme is researched and implemented by a customized circuit. Equal-spacing frequency sampling is therefore achieved in real-time. The maximum sensing distance can reach to the same length of the auxiliary interferometer. The zero-crossing detection for the beating frequency of 20MHz is achieved. Then, a nonlinearity correction method based on the self-reference method is proposed. The auxiliary interferometer is no longer necessary in this scheme. The tuning information of the laser is extracted by a strong reflectivity point at the end of the sensing arm in the main interferometer. The tuning information can then be used to resample the raw signal and the nonlinearity correction can be achieved. The spatial resolution test and the distributed sensing experiments are both performed based on this nonlinearity correction method. The results validated the feasibility of the proposed method. The method reduces the hardware and data burden for the system and has a potential value on the system integration and miniaturization.

Recently, the phase-sensitive OTDR (Φ-OTDR) based vibration sensor system has gained the focus of many researchers and some efforts have been undertaken to push further the limitations imposed on the performance of the Φ-OTDR sensor system. Then, progress in the different areas of its performance evaluation factors such as: improvement of the signal-to-noise ratio (SNR), spatial resolution (SR) in the sub-meter range, enlargement of the sensing range, frequency response bandwidth over the conventional limit and phase signal demodulation for quantitative measurement have been realized. This paper presents an overview of the recent progress in the Φ-OTDR based vibration sensing system in the different areas mentioned above.

This study aimed to determine the correlation of colour M-mode velocity propagation in the assessment of left ventricular diastolic function among acute decompensated heart failure patients with preserved ejection fraction (HFpEF). This research is an observational analytical study using a cross–sectional study design conducted from April to June 2022. The subjects of this study were patients diagnosed with acute HFpEF and treated at Dr. Soetomo General Academic Hospital, Surabaya. Patients with heart rhythm disturbances, moderate to severe valvular heart disease, and congenital heart defects were excluded from this study. Patients were measured for diastolic function including mitral valve early mitral inflow velocity (MV E Velocity), mitral peak velocity of early filling (E’) (E' Septal and E' Lateral), left atrial volume index (LAVI), The maximal tricuspid regurgitation velocity (TR V Max), Vp, the ratio of early diastolic mitral inflow velocity to early diastolic mitral annulus velocity (E/E'), the ratio between early and late ventricular filling velocity (E/A) and E/Vp Ratio. N-terminal-pro hormone B-type natriuretic peptide (NT–ProBNP) examination was also performed on study subjects as an additional diagnosis of acute heart failure. There were 33 patients who met the inclusion and exclusion criteria and were included in our study. There were 26 patients (78.8%) with grade I diastolic dysfunction, 4 patients (12.1%) with grade II diastolic dysfunction, and 3 patients (9.1%) with grade III diastolic dysfunction. There is a strong positive correlation between Vp with parameters E' Septal (p = < 0.001; r = 0.636) and E' Lateral (p = < 0.001; r = 0.650). Vp is negatively correlated with the ratio E/E' (p = 0.029; r = –0.37). The PCWP estimate with E/Vp ratio had a strong correlation with the NT–Pro BNP value > 300 pg/ml in acute HFpEF patients (p = < 0.001; r = 0.726) compared to the PCWP estimate with E/E' (p = < 0.001; r = 0.549). There is no correlation between Vp value and degree of diastolic dysfunction in patients with acute HFpEF.

Rational delineation of urban–rural boundaries is a foundational prerequisite for holistic urban and rural development planning and rational resource allocation. However, the results of division of urban–rural boundaries extracted using a single data source are non-comprehensive. To address this problem, the present study proposes a method for using multiple sources such as population data, nighttime light data, land use, and points of interest (POI) data to extract urban–rural boundaries. Considering Guizhou Province for a case study, we here present a two-step method for identifying urban–rural boundaries. First, the random forest model was combined with the dasymetric mapping method to obtain the population spatialization data with a 30-m resolution in the studied province. Second, using the breaking point method, we extracted the urban–rural boundary for Guizhou Province in 2020 based on the spatialized population. This method fully integrated the benefits of various data and judiciously extracted the boundaries of the main urban areas and small- and medium-sized towns of each city in the study province at the same spatial scale. The stratified random sampling method revealed that the average overall accuracy was 88.05%. The method proposed has certain universality and application value and allows identifying the urban–rural boundaries more accurately and practically.

The bionic polarization imaging navigation sensor (BPINS) is a navigation sensor that provides absolute heading, and it is of practical engineering significance to model the measurement error of BPINS. The existing BPINSs are still modeled using photodiode-based measurements rather than imaging measurements and are not modeled systematically enough. This paper proposes a measurement model of BPINS that takes into account the geometric and polarization errors of the optical system. Firstly, the key error factors affecting the measurement accuracy of BPINS are systematically investigated and the Stokes vector-based measurement error model of BPINS is established. Secondly, based on its measurement error model, the effect of the error source on the measurement performance of BPINS is quantitatively analyzed by using Rayleigh scattering to generate scattered sunlight as a known incident light source. The experimental results show that the coordinate deviation of the principal point has a greater impact, followed by grayscale response inconsistency of CMOS and integration angle error of micro-polarization array, and finally lens attenuation. This finding can guide the subsequent calibration of BPINS, and the quantitative results provide an important reference for its optimal design.

Any photon, regardless of its origin, carries the same optical field profile. This feature and the quantum Rayleigh emissions generate temporally discrete groups of several photons in a resonant cavity incorporating one single quantum dot. A periodic stream of single photons is distorted by high-finesse optical cavities and the quantum Rayleigh spontaneous emission in a beam splitter. Groups of photons emerge from interferometric filters because of multiple internal reflections.

The distributed fiber optic strain measurement based on Rayleigh scattering has recently become increasingly popular in automotive or mechanical engineering for strain monitoring and in the construction industry, especially structural health monitoring. This technology enables the monitoring of strain along the entire fiber length. This article addresses integrating optical fibers of different coatings into the concrete matrix to measure the shrinkage deformations. However, previous studies do not give a clear statement about the strain transfer losses of fiber optic sensors in this application. In this context, three different coating types were investigated regarding their strain transfer. The fibers were integrated into fine-grained concrete prisms, and the shrinkage strain was compared with a precise dial gauge. The analysis shows a high correlation between the reference method and the fiber measurement, especially with the Ormocer coating. The used acrylate coating is also consistent in the middle area of the specimen but requires a certain strain introduction length to indicate the actual strain. The main result of this study is a recommendation for fiber coatings for shrinkage measurement in fine-grain concretes using the distributed fiber optic strain measurement. In addition, the advantages and disadvantages of the measurement method are presented.

Cardiovascular diseases are a broadly understood concept focusing on vascular and heart dys-function. Lack of physical exercise, type 2 diabetes, obesity, hypertension, dyslipidemia, throm-boembolism, kidney, and lung diseases all contribute to the development of heart and blood vessel dysfunction. Although effective and important, traditional treatment with diuretics, statins, beta–blockers, calcium inhibitors, ACE inhibitors, and anti–platelet drugs remain a second–line treatment after dietary intervention and lifestyle changes. Scientists worldwide are still looking for an herbal product that would be quite effective and free from side effects, either taken together or before the standard pharmacological intervention. Such herbal–originated medication therapy may include Morus alba L. (white mulberry), Elaeagnus rhamnoides (L.) A. Nelson (sea–buckthorn), Allium sativum L. (garlic), Convallaria majalis L. (lily of the valley), Leonurus cardiaca L. (mother-wort), and Crataegus spp. (hawthorn). Valuable herbal raw materials include leaves, fruits, seeds, and even thorns. This short review focuses on six herbs that can constitute an interesting and po-tential therapeutic option in the management of cardiovascular disorders.

In Caucasians, basal cell carcinoma, a type of non-melanoma skin cancer, is most often found on the nose. This presents challenges for surgeons due to anatomical, functional, and aesthetic concerns. The study aimed to evaluate the distribution of tumor localization, size, morphological subtypes, surgical outcomes, radicality levels, and their correlation with recurrence rates. The research utilized data from the Hygiene Institute Health Information Centre. A retrospective analysis encompassed 343 cases of nasal skin cancer over a four-year period from January 1, 2019, to December 31, 2022. The research cohort comprised 252 female and 91 male participants, averaging 75,2 years old. Tumors were most found on the left sidewall of the nose (25.4%) and the dorsum (24.8%). The infiltrative morphological subtype was predominant (70.8%). Standard surgical excision with fasciocutaneous plastic was the preferred surgical procedure. Radical excision was achieved in 79.0% of lesions, while 16.9% were incompletely excised. Non-radically excised tumors exhibited a significantly higher recurrence rate (24.1%) compared to those with radical excision (6.3%). In nasal reconstruction, diverse surgical techniques are essential for precise adaptation based on factors like tumor characteristics and patient needs. Despite surgeons' careful adherence to excision guidelines, the potential for non-radical procedures cannot be entirely eliminated.

Localized surface plasmon resonance (LSPR) based sensors exhibit enormous potential in the areas of medical diagnosis, food safety regulation and environmental monitoring. While, the broadband spectral lineshape of LSPR hampers the observation of wavelength shifts in sensing processes, thus preventing their widespread applications in sensors. Here, we describe an improved plasmonic sensor based on Fano resonances between LSPR and Rayleigh anomaly (RA) in a metal-insulator-metal (MIM) meta-grating, which is constructed by silver nanoshells array, an isolation grating mask and a continuous gold film. The MIM configuration offers more freedoms to control the optical properties of LSPR, RA and the Fano resonance between them. Strong couplings between LSPR and RA form a series of narrowband reflection peaks (with a linewidth of ~20 nm in full width at half maximum (FWHM) and a reflectivity closing to 100%) within a LSPR based broadband extinction window in experiment, making the meta-grating promising for applications of high-efficiency reflective filters. While, a well-optimized Fano resonance between LSPR and RA by carefully adjusting the angles of incident light can switch such nano-device to an improved biological/chemical sensor with the figure of merit (FOM) large than 60 and capability for detecting the local refractive index changes caused by the bonding of target molecules on surface of the nano-devices. The figure of merit of hybrid sensor in detection of target molecules is 6 and 15 times higher than the simple RA and LSPR based sensors, respectively.

Distributed fiber optic vibration sensors based on Φ-OTDR using Rayleigh backscattering of highly coherent light source pulses are very popular type in the area of sensors due to many attractive features, mainly due to its distributed manner of sensing, i.e. they can operate as thousands of local sensors simultaneously. The paper summarizes and describes several important modifications of the original sensor scheme to enhance its key performance parameters and to extend its application potential. A multi-fiber sensor form was proposed. Single- and two-fiber sensors were designed, constructed and tested both in the laboratory and in a real environment. Variants of two-fiber sensor utilizing optical switches for the sensor flexibility enhancement are proposed and their applications are described.

Dynamic analyses and seismic assessments of multi-storey buildings at urban level require large-scale simulations and computational procedures based on simplified but accurate numerical models. At this aim the present paper propos-es an equivalent non-uniform beam-like model, suitable for the dynamic analysis of buildings with asymmetric plan and non-uniform vertical distribution of mass and stiffness. The equations of motion of this beam-like model, which pre-sents only shear and torsional deformability, are derived through the application of Hamilton’s principle. The linear dy-namic behaviour is evaluated by discretizing the continuous non-uniform model according to a Rayleigh-Ritz approach based on a suitable number of modal shapes of the uniform shear-torsional beam. In spite of its simplicity, the model is able to reproduce the dynamic behaviour of low- and mid-rise buildings with a significant reduction of the computa-tional burden with respect to that required by more general models. The efficacy of the proposed approach has been tested, by means of comparisons with linear FEM simulations, on three multi-storey buildings characterized by different irregularities. The satisfactory agreement, in terms of natural frequencies, modes of vibration and seismic response, proves the capability of the proposed approach to reproduce the dynamic response of complex spatial multi storey frames.

Soft-matter systems when driven out-of-equilibrium often give rise to structures that usually lie in-between the macroscopic scale of the material and microscopic scale of its constituents. In this paper we review three such systems, the two-dimensional square-lattice Ising model, the Kuramoto model and the Rayeligh-Bénard convection system which when driven out-of-equilibrium give rise to emergent spatio-temporal order through self-organization. A common feature of these systems is that the entities that self-assemble are coupled to one another in some way, either through local interactions or through a continuous media. Therefore, the general nature of non-equilibrium fluctuations of the intrinsic variables in these systems are found to follow similar trends as order emerges. Through this paper, we attempt to look for connections between among these systems and systems in general which give rise to emergent order when driven out-of-equilibrium.

Melting, solidification and viscosity properties of a multicomponent Fe-Cu-Nb-Mo-Si-B alloys with low aluminum addition up to 0.42 at.% Al were studied using an oscillating cup viscometer. It is shown that melting and solidification are divided into two stages with a knee point at 1461 K. The temperature dependences of the liquid fraction between the liquidus and solidus temperatures during melting and solidification are calculated. It has been proven that aluminum accelerates the processes of melting and solidification and leads to an increase in liquidus and solidus temperatures. In the liquid state at temperatures above 1700 K in an alloy with a low aluminum content, the activation energy of viscous flow increases. This growth was associated with the liquid – liquid structure transition caused by the formation of large clusters based on the metastable Fe23B6 phase. Aluminum atoms attract iron and boron atoms and contribute to the formation of clusters based on the Fe2AlB2 phase and metastable phases of a higher order.

The retrieval of tree height percentiles with satellite lidar waveforms over the mountainous ar-eas is greatly challenged due to slanted and rugged topographic relief of underlying ground. A novel algorithm is proposed to extract the height percentiles based on the target response waveform (TRW) that is resolved by using a Richardson–Lucy deconvolution algorithm with an adaptive iterative time. The height metrics of the energy percentiles of 25%, 50%, 75% and 95% for the cumulative TRW distribution are determined by their vertical distances relative to the ground elevation in this study. To validate the proposed algorithm, we select the received waveforms of the Global Ecosystem Dynamics Investigation (GEDI) lidar over the Pahvant Mountains of central Utah, USA. The results reveal that the resolved TRWs resemble closely to the actual target response waveforms from the coincident airborne lidar data, with the mean values of the coefficient of correlation, total bias and root mean square error (RMSE) taking val-ue of 0.92, 0.0813 and 0.0016. In addition, the accuracies of the derived height percentiles from the proposed algorithm have been greatly improved compared with the conventional Gaussian de-composition method and the slope-adaptive waveform metrics method. The RMSE values de-crease by the mean values of 1.96 m and 2.72 m, respectively. It demonstrates that the proposed algorithm has good potential in the extraction of forest structure parameter over rugged moun-tainous areas.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

An effective empirical statistical method is developed to improve the process of mineral resource estimation of seabed polymetallic nodules and is applied to analyse the abundance of seabed polymetallic nodules in the Clarion Clipperton Zone (CCZ). The newly proposed method is based on three hypotheses as the foundation for a model of “Idealized Nodules”, which was validated by analysing nodule samples collected from the seabed within the Tonga Offshore Mining Limited (TOML) exploration contract. Once validated, the “Idealized Nodule” model was used to deduce a set of empirical formulae for predicting the nodule resources, in terms of Percentage Coverage and Abundance. The formulae were then applied to analysing a total of 188 sets of nodule samples collected across the TOML areas, comprising box-core samples and towed camera images collected by one of the authors and detailed in [4]. The analysis also relies upon detailed box-core sample measurements from other areas reported by [7]. Numerical results for resource prediction were compared with field measurements, and reasonable agreement has been achieved. The new method has the potential to achieve more accurate mineral resource estimation with reduced sample numbers and sizes. They may also have application in improving the efficiency of design and configuration of mining equipment.

The PAX8/PPARγ rearrangement, producing the PAX8–PPARγ fusion protein (PPFP), is thought to play an essential role in the oncogenesis of thyroid follicular tumors. To identify PPFP-targeted drug candidates and establish an early standard of care for thyroid tumors, we performed ensemble docking-based compound screening. Specifically, we investigated which pocket structure should be adopted to search for a promising ligand compound for the PPFP; the position of the ligand binding pocket on the PPARγ side of the PPFP is common to that of PPARγ; however, the shape is slightly different between them due to environmental factors. We developed a method for selecting a PPFP structure with a relevant pocket and high prediction accuracy for ligand binding. This method was validated using PPARγ, whose structure and activity values are known for many compounds. Then, we performed docking calculations to PPFP for 97 drug or drug-like compounds with a thiazolidine backbone, which is one of the characteristics of ligands that bind well to PPARγ, registered in the DrugBank database. Furthermore, the binding affinities of promising ligand candidates were estimated more reliably using the molecular mechanics-Poisson–Boltzmann surface area method. Thus, we propose promising drug candidates for the PPFP with a thiazolidine backbone.

The South Asian economy is on the rise but struggling with power shortages and heavy dependence on fossil fuels. For sustained growth, there is a need for access to readily available energy sources, such as electricity. Trading clean electrical energy among neighbouring countries can ensure access to readily available points. South Asia has a diverse range of energy sources, including hydropower, that are available in the region. However, sectorial barriers can impede energy trading. This study has attempted to assess the readiness and barriers to Nepal’s cross-border energy trade with India and Bangladesh using the Analytic Hierarchy Process (AHP). This study also recommends possible measures to strengthen preparedness and address the challenges in energy trade that can be tailored and applied to other cross-country situations.

Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Large intelligent surfaces (LIS) promises not only to improve the signal to noise ratio, and spectral efficiency but also to reduce the energy consumption during the transmission. We consider a base station equipped with an antenna array using the maximum ratio transmission (MRT), and a large reflector array sending signals to a single user. Each subchannel is affected by the Rayleigh flat fading, and the reflecting elements perform non-perfect phase correction which introduces a Von Mises distributed phase error. Based on the central limit theorem (CLT), we conclude that the overall channel has an equivalent Gamma fading whose parameters are derived from the moments of the channel fading between the antenna array and LIS, and also from the LIS to the single user. Assuming that the equivalent channel can be modeled as a Gamma distribution, we propose very accurate closed-form expressions for the bit error probability and a very tight upper bound. For the case where the LIS is not able to perform perfect phase cancellation, that is, under phase errors, it is possible to analyze the system performance considering the analytical approximations and the simulated results obtained using the well known Monte Carlo method. The analytical expressions for the parameters of the Gamma distribution are very difficult to be obtained due to the complexity of the nonlinear transformations of random variables with non-zero mean and correlated terms. Even with perfect phase cancellation, all the fading coefficients are complex due to the link between the user and the base station that is not neglected in this paper.

Sensory descriptive analysis was used to evaluate the aged Feng-flavored baijiu. The results indicated that there are notable differences in the samples of different ages. The samples with shorter storage times and fresh distilled Baijiu present bran flavor, and fresh green flavor. with the increase of storage time, the fragrance of honey, sweetness, flowers, and aging gradually increases. The samples of Feng-flavored baijiu were dected by Headspace solid-phase microextraction (HS-SPME) combined with comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GC×GC–TOFMS) , in total, 496 sustances were identified in all samples, mainly containing 14 types of substances, such as esters, aldehydes etc., of which 42 substances were found in Feng-flavored baijiu for the first time. Chemometrics was used to analyze the key differential compounds. 143 differential compounds closely related to aging were preliminarily screened, and principal component analysis revealed that these samples were separated by year. 65 differential compounds were selected out by partial least squares discriminant analysis(PLS-DA). Furthermore, 43 key differential compounds were selected from the aged Feng-flavored baijiu combined with variable importance in projection and Pearson correlation coefficients. Partial least squares regression (PLSR) was used to research the correlation of sensory properties and key differential compounds, and the results indicated that most compounds were closely related to the aged Baijiu . This study afford theoretical basis and reference for flavor research of Feng-flavored baijiu.

We give a series of numerical examples of competitive evolution in the predation system, showing in some cases how the choice is made to increase the efficiency of the predation mechanism (or other significant parameters) to the detriment of populations (both of prey and predators). We then develop the mathematical theory that enables us to understand the causality involved, and identify a trend towards the emergence of the functional predation mechanism as such (and not of populations of the species involved). The realization of this trend only takes place when the conditions for it are offered by the hazards proposed to successive competitive choices. The logical structure of this trend is similar to that of the « tendency of rate of profit to fall » in certain economic models.

Knowledge-intensive business services (KIBS) are professional services that create new added value by creating, accumulating, and disseminating new knowledge. When it comes to conducting business involving new technology, KIBS play the roles of innovator, user, and producer of new technology that has led to technological innovation. This study aimed to determine the role of KIBS as a tool for innovation in a country’s economic system. Specifically, the degree and role of their impact on the Korean economy were analyzed and compared for the entire KIBS sector, T-KIBS (a new technology-based professional service), P-KIBS (a traditional professional service), and every subsector. For this purpose, the demand-inducement model, supply inducement model, and interlinkage effects method were applied using the 2019 input-output table published in 2022. The analysis showed that the indirect production inducement effect of the entire KIBS industry on other industries was 0.800 KRW, the indirect added value inducement effect was 0.330 KRW, and the supply disruption effect was 1.144 KRW. For T-KIBS, the indirect production inducement effect was 0.687 KRW, the indirect added value inducement effect was 0.272 KRW, and the supply disruption effect was 0.730 KRW. For P-KIBS, the indirect production inducement effect was 1.472 KRW, the indirect added value inducement effect was 0.646 KRW, and the supply disruption effect was 2.657 KRW. Finally, regarding the economic ripple effect of the KIBS subsector, legal and management support services and advertisements corresponding to P-KIBS showed higher figures than the T-KIBS subsectors in all sectors, including production inducement, the added value inducement effect, and the supply disruption effect. These results revealed that in the South Korean economic system, KIBS contribute to production and value addition across all industrial sectors. It is apparent that the absence of supply significantly disrupts other industries. Furthermore, production inducement effects are evenly distributed among all the KIBS subsectors in the secondary and tertiary sectors, while the value-added effects have a greater impact on the tertiary sector. In terms of the supply shortage effects, the secondary sector experiences a more significant impact. This underscores the crucial role of KIBS in sustaining and enhancing overall economic activity in South Korea. This study is significant in that it not only investigated KIBS as an industry group using the advantages provided by industry linkage analysis but also examined and compared detailed subsectors, thereby elaborately evaluating the influence relationship between KIBS and other industries. Therefore, the results presented in this study are expected to be useful for fostering the KIBS industrial sector and establishing economic innovation policies using KIBS.

Physical properties like shape, volume and size affect the dynamics of biological systems. Along these lines, we focus on the topological properties of biological fluids and their biochemical and physiological outcomes. We take as a paradigmatic example the salivary fluid and describe how its topological features may affect the physiopathology of the oral cavity. Topological approaches assess the general properties of saliva, ignoring small-scale physical details such as density, flow rate, stiffness, viscosity. Specifically, the mucin aggregates scattered in the salivary fluid can be tackled in terms of topological holes, i.e., vortical clusters that modify the direction, flow, impulse, local rate-of-change and velocity of saliva. While the current methodological approaches are inclined to remove the effects of impurities assessing systems as homogeneous structures, we argue that the occurrence of mucins breaks up the salivary fluid’s homogeneity, leading to unexpected biophysical modifications. We suggest that every collected salivary sample is not reliable for accurate clinical and experimental investigation, since it displays highly local as well as variable chemical, physical and biological features, not reflecting the current physiological state of the oral cavity. Therefore, the assessment of a single salivary sample is not fully reproducible and cannot provide information about the biophysical, enzymatic and microbiological content of the whole saliva. In sum, the very topological features of the saliva - such as volume, shape, antipodal cells, vortex area, whirling fluid mass, segmentation, discretization, triangulation, node numbering - produce unnoticed biological consequences and network connectivity features with intriguing operational implications.

Tropical sea surface temperature (SST) variability, mainly driven by the El Niño–Southern Oscillation (ENSO), influences the atmospheric circulation and hence the transport of heat and chemical species in both the troposphere and stratosphere. This paper uses Met Office, ERA5 and MERRA2 reanalysis data to examine the impact of SST variability on the dynamics of the polar stratosphere and ozone layer over the period 1980 to 2020. Particular attention is paid to studying the differences in the influence of different types of ENSO (East Pacific (EP) and Central Pacific (CP)) for the El Niño and La Niña phases. It is shown that during the EP El Niño, the zonal wind weakens more strongly and changes direction more often than during the EP El Niño, and the CP El Niño leads to a more rapid decay of the polar vortex (PV), an increase in stratospheric air temperature and an increase in the concentration and total column ozone than during EP El Niño. For the CP La Niña, the PV is more stable, which often leads to a significant decrease in Arctic ozone. During EP La Niña, powerful sudden stratospheric warmings are often observed, which lead to the destruction of PV and an increase in column ozone.

Maximal quantum correlations of unity do not violate the CSHS-Bell inequalities because the remaining two correlations vanish. The probability of coincident detections should not be confused with the correlation of mixed states. The theoretical requirements for implementing the quantum nonlocality theory are not present in the experimental configurations purporting to prove Bohr’s or Bell’s nonlocality because of the quantum Rayleigh scattering of single photons. By means of a normalization factor corresponding to the total number of initiated events, the detection probabilities obtained experimentally are too small to enable any violation of a Bell inequality. Correlations between independent states of qubits can easily outperform those calculated with entangled photons. Additionally, the quantum joint probability for a Bell state can be factorized enabling a local detection of the alleged quantum nonlocality, if it existed. © The Author 2023

Optical fiber measurement systems have recently gained popularity following a multitude of intensive investigations. A new technique has been developed for these measurement systems that uses Rayleigh backscatter to determine the distributed strain measurement over the total length of a fiber. These measurement systems have great potential in civil engineering and structural health monitoring. This paper addresses some preliminary comparisons between three different fiber coatings and six different adhesives on steel structures. The results are based on a bending test with specimens made of precision flat steel; optical fiber strain measurements were compared with photogrammetric strain measurements. Analysis of the test data showed a strong correlation between the optical measurement system’s results and the theoretical results up to the yielding point of the steel. Furthermore, the results indicate that fibers with the Ormocer® and polyimide coatings have almost no loss in the strain measurements. The main results of this investigation are a guideline describing how to attach optical fibers to steel surfaces for distributed fiber optical strain measurements and recommendations for coatings to obtain realistic strain values. Additionally, the advantages of distributed strain measurements were revealed, which illustrates the potential of Rayleigh backscattering applications.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

Few studies have examined the pros and cons of integrated TB and HIV service delivery in public healthcare facilities, and even fewer have proposed conceptual models for improved integration. This study intends to fill that vacuum by outlining the development of a facility-based paradigm for integrating TB, HIV and patients services. The design of the proposed model were in stages that involved the evaluation of existing TB-HIV integration model and synthesis of both quantitative and qualitative data from the study sites which were selected public healthcare facilities at both rural and peri-urban settings in Oliver Reginald (O.R) Tambo District Municipality in Eastern Cape, South Africa. Secondary data on 2009-2013 TB-HIV clinical outcomes were obtained from multiple sources for quantitative analysis. Qualitative data involved focus group discussions among patient and heath care staff, which was thematically analysed. The development of a possibly better model and validation of this model show that the district's health system was reinforced by the model's guiding principles, which placed a strong emphasis on inputs, processes, outcomes, and integration effects.The model is adaptable to different healthcare delivery systems but will require support from healthcare stakeholders and professionals to be successful.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

Real and complex analytic functions are largely studied in the field of complex analysis and are seen as very useful tools in solving problems in mathematics, physics and engineering. Real and complex numbers are a subset of semi-structured complex numbers (a new number set created to algebraically solve division by zero). Nevertheless, the properties of analytic functions made up of semi-structured complex variables (called semi-structured complex analytic functions) is yet to be explored. This limits the range of possible problems that can be resolved using analytic functions). In this regard, the aim of this paper was to expound upon the properties of semi-structured complex analytic functions and show their application in solving engineering problems. The results of this paper included (1) developing a full set of Cauchy–Riemann Equations for the semi-structured complex -space; (2) define sufficient and necessary conditions for a semi-structured complex function to be analytic; (3) determine the relationship between semi-structured complex analytic functions, Laplace’s Equations and Poisson’s Equations; and (5) provide an example of the use of these functions.

Three physical elements are missing from the conventional formalism of quantum photonics: 1) the quantum Rayleigh spontaneous and stimulated emissions; 2) the unavoidable parametric amplification; and 3) the mixed time-frequency spectral structure of a photonic field which specifies its duration or spatial extent. As a single photon enters a dielectric medium, the quantum Rayleigh scattering prevents it from propagating in a straight-line, thereby destroying any possible entanglement. A pure dynamic and coherent state composed of two consecutive number states, delivers the correct expectation values for the number of photons carried by a photonic wave front, its complex optical field, and phase quadratures. The intrinsic longitudinal and lateral field profiles associated with a group of photons for any instantaneous number of photons are independent of the source. These photonic properties enable a step-by-step analysis of the correlation functions characterizing counting of coincident numbers of photons or intensities with unity visibility interference, spanning the classical and quantum optic regimes

An explosive growth in vehicular wireless services and applications gives rise to spectrum resource starvation. Cognitive radio has been used to vehicular networks to mitigate the impending spectrum starvation problem by allowing vehicles to fully exploit spectrum opportunities unoccupied by licensed users. Efficient and effective detection of licensed user is a critical issue to realize cognitive radio applications. However, spectrum sensing in vehicular environments is a very challenging task due to vehicles mobility. For instance, vehicle mobility has a large effect on the wireless channel, thereby impacting the detection performance of spectrum sensing. Thus, gargantuan efforts have been made in order to analyze the fading properties of mobile radio channel in vehicular environments. Indeed, numerous studies have demonstrated that the wireless channel in vehicular environments can be characterized by a temporally correlated Rayleigh fading. In this paper, we focus on energy detection for spectrum sensing and a counting rule for cooperative sensing based on Neyman-Pearson criteria. Further, we go into the effect of the sensing and reporting channels condition on spectrum sensing performance under temporally correlated Rayleigh sensing channel. For local and cooperative sensing, we derive some alternative expressions for average probability of miss detection. The pertinent numerical and simulating results are provided to further validate our theoretical analyses under a variety of scenarios.

The presence of the quantum Rayleigh scattering, or spontaneous emission, inside a dielectric medium such as a beam splitter or an interferometric filter, prevents a single-photon from propagating in a straight-line. Modelling a beam splitter by means of a unitary transformation is physically meaningless because of the loss of photons. Additional missing elements from the conventional theory are: 1) the quantum Rayleigh stimulated emission which can form groups of photons of the same frequencies, and 2) the unavoidable parametric amplification of single-photons in the original parametric crystal. An interference filter disturbs, through multiple internal reflections, the original stream of single-photons, thereby confirming the existence of groups of photons being spread out to lengthen the coherence time. The approach of modelling individual, single measurements with statistical ensemble probability amplitudes leads to the counterintuitive explanations of the experimental outcomes and should be replaced with pure states describing instantaneous measurements which are afterwards averaged.

The paper deals with the Compound Inverse Rayleigh distribution, shown to constitute a proper model for the characterization of the probability distribution of extreme values of wind-speed, a topic which is gaining growing interest in the field of renewable generation assessment, both in view of wind power production evaluation and the wind-tower mechanical reliability and safety. The first part of the paper illustrates such model starting from its origin as a generalization of the Inverse Rayleigh model - already proven to be a valid model for extreme wind-speeds - by means of a continuous mixture generated by a Gamma distribution on the scale parameter, which gives rise to its name. Moreover, its validity to interpret different field data is illustrated, also by means of numerous numerical examples based upon real wind speed measurements. Then, a novel Bayes approach for the estimation of such extreme wind-speed model is proposed. The method relies upon the assessment of prior information in a practical way, that should be easily available to system engineers. In practice, the method allows to express one’s prior beliefs both in terms of parameters, as customary, and/or in terms of probabilities. The results of a large set of numerical simulations – using typical values of wind-speed parameters - are reported to illustrate the efficiency and the accuracy of the proposed method. The validity of the approach is also verified in terms of its robustness with respect to significant differences compared to the assumed prior information.

Nanoporous membranes promise energy-efficient water desalination. Hexagonal boron nitride (h-BN), like graphene, exhibits outstanding physical and chemical properties, making it a promising candidate for water treatment. We employed Car–Parrinello molecular dynamics simulations to establish accurate modeling of Na+ and Cl- permeation through hydrogen passivated nanopores in graphene and h-BN membranes. In these complex systems the classical potentials cannot properly account for the physics at play. We demonstrate that ion separation works well for the h-BN by imposing a barrier of 0.13 eV and 0.24 eV for Na+ and Cl- permeation respectively, compared to the graphene where the Cl- ion faces a negative barrier of 0.68 eV and is prone toward blockade and Na+ permeation is associated with a slightly negative barrier of 0.03 eV. From the change in the solvation shell, we get the following trend: Na/h-BN > Na/G > Cl/G > Cl/h-BN. We argue that the trend in the permeation barrier changes to Cl-h-BN > Na-h-BN > Na-G > Cl-G due to a combination of several interactions, including the distortion of the water network induced by the ions, the ion-water interaction, and the ion-nanopore interaction. Overall, the desalination performance of h-BN surpasses that of their graphene counterparts.

The role of initial state (ISI) and final state (FSI) ion–ion interactions in heavy ion double charge exchange (DCE) reactions A(Z,N)→A(Z±2,N∓2) are studied in the context of double single charge exchange (DSCE) reactions given by sequential actions of the isovector nucleon–nucleon (NN) T–matrix. The second order DSCE reaction amplitude is investigated in momentum representation in a formulation, focused on the extraction of nuclear matrix elements under the conditions of strong initial state (ISI) and final state (FSI) interactions. In closure approximation and using the momentum representation, the reaction amplitude is finally separated into ISI/FSI distortion coefficients and reaction kernels and nuclear matrix elements. The ISI/FSI reaction kernels emerge as the result of the repeated scattering on the avoided volume, introduced by the imaginary parts of the ion–ion optical potential and acting as sinks for the quantal probability current. The closure approximation allows derive a set of induced effective two–body isotensor interactions, given by products of spin–scalar, spin–vector central and rank–2 spin–tensor interactions. The intermediate propagator plays a key role in establishing correlation between the DCE transitions in the projectile and target nucleus. The presented approach emphasizes the special features of DSCE reaction dynamics as proceeding like a system of two coupled isospin dipoles whose strengths are determined by the momentum-space form factors of the NN isovector interaction. The properties of the DSCE interaction form factors are investigated and the approach is applied to data.

Periodontitis is a disease that originates from gingival tissue, and if left untreated, can cause inflammation to spread to deeper tissues, altering bone homeostasis, and even leading to tooth loss. When the bacteria in plaque reach sufficient numbers, the immune system responds by activating immune cells that will produce cytokines, including interleukin-1 (IL-1), interleukin-6 (IL-6), and tumor necrosis factor-alpha (TNF-α). These immune signaling molecules will coordinate the inflammatory responses. IL-1 binds to the IL-1 receptor (IL-1R) on the surface of target cells, initiating an inflammatory response by activating intracellular signalling pathways. Inhibition of IL-1R can prevent the interaction of IL-1 with this receptor, thereby halting the activation of the inflammatory pathway. By substituting this connection with active anti-inflammatory substances, it is possible to prevent the contact between IL-1 and IL-1R. The licorice plant, Glycyrrhiza glabra, includes eight types of flavonoids with significant anti-inflammatory potential, namely isoliquiritigenin, glyzaglabrin, prunetin, shinpterocarpin, licochalcone A, glabridin, glisoflavone, and isoangustone A. This study aims to assess the potential of such flavonoids as candidates for periodontitis treatment through molecular docking, using AutoDock Tools v.1.5.6. All tested compounds showed highly stable bonds to IL-1R, with a binding affinity values below -7 kcal/mol. Van der Waals forces, hydrogen bonds, and hydrophobic bonds all contribute to the stability of these interactions. Among the eight tested compounds, glisoflavone, which has a Ki value of 90.89 nM and a ΔG value of -9.61 kcal/mol, has the highest binding stability to IL-1R.

Quantum cryptography revolutionizes secure information transfer, providing defense against both quantum and classical computational attacks. The primary challenge in extending the reach of quantum communication comes from the exponential decay of signals over long distances. Addressing this challenge, we have developed Quantum-protected Control-based Key Distribution (QCKD), overcoming transmission range limitations by monitoring signal leakages and rendering leaked quantum states significantly non-orthogonal. This paper reports on the experiments with the QCKD, conducted over a 1,707 km fiber line. We demonstrate advancements in critical components of the protocol, showing its remarkable scalability and adaptability for extended distances and multi-user configurations.

Biosensors detect specific bio-analytes by generating a measurable signal from the interaction between the sensing element and the target molecule. Surface acoustic wave (SAW) biosensors offer unique advantages due to their high sensitivity, real-time response capability, and label-free detection. The typical SAW modes are the Rayleigh mode and the shear-horizontal mode. Both present pros and cons for biosensing applications and generally need different substrates and device geometries to be efficiently generated. This study investigates and characterizes ultra-high-frequency (UHF-) SAW resonator biosensors. It reveals the simultaneous presence of the two typical SAW modes, clearly separated in frequency, called slow and fast. The two modes are studied by numerical simulations and biosensing experiments with the glial-fibrillary-acidic-protein (GFAP) biomarker. The slow mode is generally more sensitive to changes in surface properties, such as temperature and mass changes, by a factor of about 1.4 with respect to the fast mode.

Non-Orthogonal Multiple Access (NOMA) is the key technology promised to be applied in next-generation networks in the near future. In this study, we propose a multi-points cooperative relaying (MPCR) NOMA model instead of just using a relay as the previous studies. Based on the channel state information (CSI), the base station (BS) selects a closest user equipment (UE) and sends a superposed signal to this UE as a first relay node. We have assumed that there are N UEs in the network and Nth UE, which is farthest from BS, has the poorest quality signal transmitted from the BS compared other UEs. Nth UE received the forwarded signal from N-1 relaying nodes that are UEs with better signal quality. At the ith relaying node, it detect its own symbol by using successive interference cancellation (SIC) and will forward the composite signal to the next closest user, namely i+1th UE, and include an excess power which will use for energy harvesting (EH) intention at the next UE. By these, the farthest UE in network can be significantly improved. In addition, closed-form expressions of outage probability for users over both the Rayleigh and Nakagami-m fading channels are also presented. Analysis and simulation results performed by Matlab software which are presented accurately and clearly show that the effectiveness of our proposed model and this model consistents with the multi-access wireless network in future.

The quinoline derivative, N-(7-chloro-4-morpholinoquinolin-2-yl)benzamide, was synthesized in a conventional three-step procedure from 4,7-dichloroquinoline using N-oxidation reaction/C2-amidation reaction/C4 SNAr reaction sequence. The structure of the compound was fully characterized by FT-IR, 1H‐, 13C-NMR, DEPT-135°, and ESI-MS techniques. Its physicochemical parameters (Lipinski’s descriptors) were also calculated using the online SwissADME database. Such derivatives are relevant therapeutic agents exhibiting potent anticancer, antibacterial, antifungal, and antiparasitic properties.

Epithelial–mesenchymal transition (EMT) is defined as a cellular process during which epithelial cells acquire mesenchymal phenotypes and behavior following the downregulation of epithelial features. EMT and its reversed process, the mesenchymal-epithelial transition (MET), and the special form of EMT, the endothelial-mesenchymal transition (EndMT), have been thought as a universal dogma controlling developmental and pathological processes. More than half a century of EMT study has made it a large research field and a mainstream concept. However, discrepancies and disputes over EMT and EMT research have also grown over time. Particularly, neither the epithelial and mesenchymal states/properties nor their regulatory networks nor specific markers have been defined, rendering the EMT, MET and EndMT concepts groundless. Moreover, EMT and MET effects should not be a cause, but rather a consequence of or an accompanying effect during developmental and pathological processes. EMT and MET represented by the change in cell shapes or adhesiveness or symbolized by EMT factors are biased interpretation of the overall change in cellular property and regulatory networks during development and cancer progression. The true meaning of EMT effects in some developmental and pathological processes, such as fibrosis, needs re-evaluation. But the core EMT factors are actually a few components of the regulatory networks of neural stemness, which determines tumorigenicity and pluripotency. The EMT effects in cancer progression and neural crest formation are wrong attribution of the role of neural stemness during cancer progression and the cell-intrinsic property of neural crest cells to the unknown mesenchymal state. It is time to reassess the significance of EMT and its related concepts in scientific research.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

This research explores the predictive capabilities of autonomous driving systems by integrating human factor considerations within the context of safety-critical events. Recognizing the significance of human behaviors in influencing driving dynamics, the study employs advanced modeling techniques to enhance the accuracy of predictions in scenarios that demand heightened safety measures. Traditional rule-based systems and monotonic logic often fall short in addressing the complexities of safety-critical events. To overcome these limitations, the research proposes the application of non-monotonic logic, allowing for flexible and adaptive reasoning that accommodates exceptions and context-specific information.The study emphasizes the importance of incorporating individual differences among drivers, such as risk-taking tendencies, reaction times, decision-making processes, and driving styles. By considering these human factors, the research aims to develop realistic and accurate autonomous driving models that capture the nuances of real-world driving scenarios, especially in safety-critical situations. The predictive model takes into account both internal and external factors, enabling the autonomous system to anticipate and respond effectively to unforeseen events.The primary goal is to provide autonomous vehicles with the capability to make plausible inferences, handle conflicting data, and adapt their behavior in real-time during safety-critical events. The proposed model integrates personalized cognitive agents for each driver, incorporating their unique preferences, characteristics, and needs. This personalized approach aims to optimize the safety and efficiency of autonomous driving, contributing to the ongoing evolution of intelligent transportation systems.In conclusion, this research contributes to advancing the field of autonomous driving by introducing a predictive model that leverages human factor considerations to enhance safety in safety-critical events. The incorporation of non-monotonic logic and individualized cognitive agents signifies a comprehensive approach to address the challenges associated with predicting autonomous driving behavior, paving the way for safer and more reliable autonomous vehicles in dynamic and unpredictable environments.

In general, a superconductor has zero resistance, although it requires significant refrigeration or high pressures with high manufacturing costs, which prevents it into practical applications. In other words, solving these issues implies main superconducting researches. To solve these problems, this paper describes a new type of superconductivity, which is independent for temperatures and which operates without pressures. The principles of the presented system are as follows:First a voltage source, a current source and a load are connected in series. Then, the voltage of the voltage source is adjusted to balance the voltage of the load. Under this condition, the balance of the two voltages provides a zero voltage between the taps of the current source and the generated current from the voltage source becomes zero because of the internal infinite resistance of the current source. As a result, the electric powers generated by the two sources are zero, and therefore, the load cannot generate Joule heating because of energy conservation. However, the current from the current source (not the voltage source) is not zero; therefore, we can predict that the resistance of the load must be zero. As a theory, we derived a new electric field and transient attractive force, which result in a very short coherence of an electron pair because there is not the Coulomb repulsive force due to the existence of the above transient attractive force. Note that both the forces are derived by the Poisson equation, which implies that they cannot be compatible. Therefore, the pair combination energy from spins becomes extremely strong, which is not destroyed by the normal heat energy. Moreover, every center-of-mass motion of electron pair results in the Bose-Einstein condensation and the macroscopic wave function, which produces the London equation (i.e., the Meissner effect). Moreover, by introducing the equivalent circuit, this paper conducted numerical calculations. As a result, we could derive numerically zero resistance and responses for additional static magnetic fields as a discharged current, which implies the Meissner effect. Note that this paper has prepared Appendix section, which provides a guide to reproduce actual experiments and preliminary experimental results. These results in the Appendix indicate the zero resistances and Meissner effects.

The aim of this study is to obtain the Bayes estimators and the maximum likelihood estimators (MLEs) for the unknown parameters of the Rayleigh Weibull (RW) distribution based on progres-sive type-II censored samples. The approximate Bayes estimators are calculated using the idea of Lindley and Tierney-Kadane's approximation method under the squared-error loss function when the Bayes estimators are not handed in explicit forms. In this study, the approximate Bayes esti-mates are compared with the maximum likelihood estimates in the aspect of the estimated risks (ERs) using Monte Carlo simulation. In addition, the coverage probabilities of the parametric bootstrap estimates are calculated. Real lifetime data sets belonging to the cancer types as bladder cancer, head and neck cancer, and leukemia are used to illustrate the emprical results belonging to the approximate Bayes estimates, the maximum likelihood estimates, and the parametric bootstrap intervals.

Vanadium(IV) chalcogenide materials are of increasing interest for use in catalysis and energy conversion-related applications. Since no ternary compounds are yet known in the V–Se–Te system, we studied ternary VwSeyTe2–y (w = 1.10, 1.13; y = 0.42, 0.72) phases crystallizing in space group P3m1 (no. 164). Two single-crystal specimens with differing compositions of a solid solution were obtained using the ceramic method. All products were characterized by either single-crystal or powder X-ray diffraction. The lattice parameters increase with rising tellurium content in accordance to the larger ionic radius of the tellurium anion compared to selenium. The chemical compositions were confirmed by energy dispersive X-ray spectroscopy. Further, magnetic measurements revealed mostly antiferromagnetic properties. Simultaneous differential scanning calorimetry/thermogravimetric analyses in nitrogen atmosphere showed endothermic decomposition accompanied by the formation of VN. The results of this work can serve as a basis for the synthesis of new phases in the V–Se–Te and related vanadium chalcogenide systems.

The swift progress in low-dimensional nanocarbons, specifically in the realm of the authentic one-dimensional carbon chain featuring sp¹ hybridization, has unveiled exciting prospects for integrating them into cutting-edge technologies across diverse industries. To fully harness their potential, precise control over the growth process is necessary to obtain desired nanostructure and functionality. However, optimizing properties through traditional approaches has been challenging due to complex interactions. To address this, we implement a focused data-driven strategy for nanocarbon inverse design by leveraging a state-of-the-art data-driven nanocarbon genome approach (NCGA). By uncovering relationships between growth parameters and resultant traits, this serves as an expedient catalyst in engineering nanostructures with tailored attributes. We introduce an extensive array of technological approaches aimed at precisely controlling the growth process. These methods encompass stimulating and precisely adjusting synergistic effects, coordinating atomic vibrations at a collective level through the implementation of multilayer nano-interfaces, harnessing the potential of active screen plasma surface engineering, utilizing nano-patterning and allotropic phase transformations, incorporating heteroatom doping, and effectively directing self-assembly. These aim to unlock nanomaterials' latent potential and reveal novel neural pathways within the data-driven NCGA, enhancing its predictive capabilities. Specifically, triggering self-organization during growth can potentially unlock previously unexplored neural pathways. The data-driven NCGA offers a paradigm shift, accelerating discovery and design of nanocarbons with optimized, application-specific properties.

The aim of the present work is to explore a different non-traditional approach to higher dimensional spacetime which differs from the usual approaches such as large extra space dimensions, warped extra space dimensions and multiple extra time dimensions. This approach will be referred to as "Dynamic" higher dimensional spacetime. By this term will be introduced a new kind of higher dimensional spacetime (more than the usual 3+1 dimensions), which behaves dynamically in the sense that time is not a fixed dimension but is the extra plus one dimension to the spatial dimensions of the phenomenon we are studying. For a higher dimensional phenomenon, the lower dimensional time will behave as space and the new time will be a plus one dimension, meaning if we study a 3-dimensional phenomenon then time is the usual 4th dimension but if we are studying a 4-dimensional phenomenon then its time will be an extra 5th dimension and for this phenomenon the 4th dimension will behave as space. All spatial dimensions are indistinguishable from each other and behave in the exact same way, which means that the important parameter is not the dimension we are studying (for example the 4th or the 5th) but the number of dimensions in which a phenomenon can interact and how higher dimensional phenomena interact with lower ones. This non-traditional approach to higher dimensional spacetime may appear confusing at first but will become clearer in the rest of the paper. For this reason, we will first associate the time dimension with propagation relative to space dimensions and change orthogonal to them in order to give the reader a better intuition. Following that, we will describe how higher - dimensional phenomena would appear to us, the 3 - dimensional observer and try to set some guidelines on how we should mathematically model higher - dimensional phenomena in order for us to make accurate predictions of their behaviour. Then we will express the general framework of a "Dynamic" higher - dimensional spacetime and turn our gaze to 4+1 – dimensional phenomena. We will explore how a mass term arises for 4 – dimensional waves by generalizing the frequency – speed – wavelength relation of 3D waves and give a basic description on a possible way to describe a 4+1 – dimensional disturbance in a scalar Energy Field in order to make accurate predictions on our 3+1 dimensional plane. In this framework we will derive the Klein – Gordon equation by generalizing the wave equation and ignoring all lower than 4+1 - dimensional disturbances and compere our mass term findings with the Klein – Gordon equation mass term and with results from gravity – induced quantum interference experiments. Lastly, we will describe how a "Dynamic" 5 - dimensional spacetime would appear in a 3D observer and examine whether our findings are compatible with quantum mechanics and the special theory of relativity.