The safe and efficient mining of coal seams with low porosity, low permeability and high inhomogeneity under complex geological conditions is a major challenge, among which the permeability of coal seams is crucial for coal mine gas extraction. The development of coal seam permeability enhancement technology can help coal mines to produce safely and efficiently, and the extracted coal bed methane can be utilized as a green energy. In order to study the effect of freezing and thawing on the evolution of mechanical and permeability properties of coal, triaxial permeability tests were carried out on low-permeability coal under two kinds of surrounding pressures. At the same time, dry, saturated and freeze-thaw coal were set up for comparison, and the effects of water and freeze-thaw were separated from each other. The triaxial mechanics and percolation laws of dry, saturated and freeze-thaw coal rocks were obtained, and the mechanism of the influence of freeze-thaw on the permeability evolution law of coal was revealed. The research results can provide theoretical guidance for the gas extraction technology of low permeability coal seams with increased permeability.

The swelling behavior of titanium-modified austenitic stainless steel 15-15Ti was investigated by pre-implantation of He at room temperature followed by Ni irradiation at 580 °C to peak doses of 120, 240 and 400 dpa. Relatively smaller cavities were observed in the zone of helium implantation while large cavities appeared in the region near the damage peak. A correction formula of the dpa curve was proposed and applied for samples with large swelling. It is found that the steady-state swelling rate of 15-15Ti keeps at ~1% /dpa even to high doses. By comparing the swelling data of the helium-implanted and helium-free regions at same doses, 70 dpa and 122 dpa, the suppression of excessive helium on swelling can be deduced at such doses.

In the present paper, we introduce the phytoscreening and antiradical characteristics of conker extracts prepared from 2-, 1-year stored and just collected plants as well as the anti-inflammatory effect of oinment composition based on the extract.

The nucleation of voids in alpha iron and the influence of carbon were investigated through a combination of rate theory and nucleation theory calculations. The steady rates of void nucleation exhibit high sensitivity to carbon. Even a seemingly negligible carbon concentration, as low as a few atomic parts per million (appm), can dramatically reduce the nucleation rates and narrow the temperature window for nucleation. This study highlights the challenges in certifying and qualifying nuclear materials for use in reactor environments. It emphasizes the necessity for precise control of impurity levels during materials processing and stringent requirements for irradiation testing, which are susceptible to contamination. Furthermore, the study provides an explanation for the significant data scattering observed in void swelling behaviors as reported in the literature.

Hydrogels incorporated with hydrophobic motifs have received considerable attention to recapitulate the cellular microenvironments, specifically for the bio-mineralization of a 3D matrix. Introduction of hydrophobic motifs into a hydrogel often results in irregular arrangement of the motifs, and further phase separation of hydrophobic domains, but limited efforts have been made to resolve this challenge in the hydrophobically-modified hydrogel. Therefore, this study presents an advanced integrative strategy to incorporate hydrophobic domains regularly in a hydrogel by self-assembling of polymer cross-linkers, building blocks of a hydrogel. Self-assemblies between polymer cross-linkers were examined as micro-domains to incorporate hydrophobic motifs in a hydrogel. The self-assembled structures in a pre-gelled solution were confirmed with the fluorescence analysis and the hydrophobicity of a hydrogel could be tuned by incorporating the motifs in a controlled manner. Overall, the results of this study would greatly serve to tuning performance of a wide array of hydrophobically-modified hydrogels in drug delivery, cell therapies and tissue engineering.

Considering the current energy environment, both efficient and environmentally friendly solutions have to be developed for building construction. Bio-based building materials offer new perspectives through their insulating and natural humidity regulation capacities. Nevertheless, these materials are as complex as they are promising and grey areas still remain regarding their behavior. Their water sorption and desorption curves recorded in experimental work demonstrate a hysteresis phenomenon and, although plausible hypotheses have been formulated in the literature, there is currently no consensus on its causes. Furthermore, it is important to emphasize that no reference considers the hydrophilic nature of the resource. Yet this is a specificity of raw material coming from the plant world. In this context, this paper explores the microstructure and chemical composition of plant aggregates to propose a new explanation for the hysteresis. It is based on recent work demonstrating the existence of differentiated hydrogen bonds between the water sorption and desorption phase in cellulose. Obviously, hysteresis also has an origin at the molecular scale. Lastly, the hypothesis put forward here is supported by the swelling of bio-based materials that has been observed at high relative humidity and this study aims to identify a link between the mechanical (swelling/shrinking) of bio-based materials and their hygroscopic behavior. This leads to a better understanding of the hydro-mechanical coupling of these materials.

Freeze drying was compared with spray drying regarding feasibility to process wild thyme drug in order to obtain dry formulations at laboratory scale starting from liquid extracts produced by different extraction methods: maceration, heat-, ultrasound-, and microwave-assisted extractions. Higher powder yield (based on the dry weight prior to extraction) was achieved by freeze than spray drying and lower loss of total polyphenol content (TPC) and total flavonoid content (TFC) due to the drying process. Gelatin as a coating agent (5% w/w) provided better TPC recovery by 70% in case of lyophilization and higher powder yield in case of spray drying by diminishing material deposition on the wall of the drying chamber. The resulting gelatin-free and gelatin-containing powders carried polyphenols in amount ~190 and 53-75 mg gallic acid equivalents GAE/g of powder, respectively. Microwave-assisted extract formulation distinguished from others by higher content of polyphenols, proteins and sugars, higher bulk density and lower solubility. The type of the drying process affected mainly position of the gelatin-derived -OH and amide bands in FTIR spectra. Spray dried formulations compared to freeze dried expressed higher thermal stability as confirmed by differential scanning calorimetry analysis and higher diffusion coefficient; the last feature can be associated with the lower specific surface area of irregularly shaped freeze-dried particles (151-223 µm) compared to small microspheres (~8 µm) in spray-dried powder.

Traditionally, studies on freeze–thaw erosion have used the analytic hierarchy process (AHP) to calculate the weight of evaluation factors, however, this method cannot accurately depict the fuzziness and randomness of the problem. To overcome this disadvantage, the present study has proposed an improved AHP method based on the cloud model to evaluate the impact factors in freeze–thaw erosion. To establish an improved evaluation method for freeze–thaw erosion in Tibet, the following six factors were selected: annual temperature range, average annual precipitation, slope, aspect, vegetation coverage, and topographic relief. The traditional AHP and the cloud model were combined to determine the weight of the impact factors, and a consistency check was performed. The comprehensive evaluation index model was used to evaluate the intensity of freeze–thaw erosion in Tibet. The results show that freeze–thaw erosion is extensive, stretching over approximately 66.1% of Tibet. The problem is the most serious in Ngari Prefecture and Nagqu. However, mild erosion and moderate erosion, accounting for 37.1% and 25.0%, respectively, of the total freeze–thaw erosion are the most widely distributed. The evaluation results for the freeze–thaw erosion was confirmed to be consistent with the actual situation. In brief, this study provided a new approach to evaluate the conditions of freeze–thaw erosion quantitively in Tibet.

Minimum miscibility pressure (MMP) and oil swelling are two important factors of carbondioxide (CO₂) gas displacement mechanism occurred in the reservoir relate to application of CO₂ injection in the field to enhance oil recovery. In this paper determination of minimum miscibility pressure (MMP) between crude oil samples with carbondioxide gas conducted using two methods, i.e. correlation methods and laboratory experiment using slimtube. While, determination of swelling factor was conducted using PVT cell, where recombined fluid injected and conditionally at the reservoir temperature. The results of MMP using empirical equation (2807 Psig) and Holm & Josendal correlation (2750 Psig) is more approximate to the result of laboratory analysis (2805 Psig). The result of swelling test during injection CO₂ gas processes until 46.82% mole, shows that bubble point pressure is increasing gradually from 410 psig through 2200 psig, and swelling factor was also increase from 1.0 through 1.442. Based on the value of fracture pressure of Layer F in the KHL Field is 2200 Psig and MMP is 2805 Psig, hence the application of CO₂ gas injection in the field only could be conducted as immiscible flooding.

The research aims to improve some of the physical and hydro-physical properties of some Vertisols in the southern region (part of the eastern Houran Plateau) in Sweda Governorate at the south of Syria. Using different quantities of volcanic ash, soil samples were collected from the Al-Thahallah village from a depth of (0-30) cm, The experiment was designed according to the complete random design with one factor that represents the ash quantity (1.25, 2.5, 5) %, with three replicates for each treatment in addition to the control treatment a0. The experiment was carried out within the plastic pots during agricultural season 2018/2019, in which the wheat of the Sham variety 3 were cultivated as a cover plant. The results showed that the addition of volcanic ash at the quantity of 5% led to a significant increase in the infiltration rate by (328.60) %,%, where the filtration rate increased from 0.42 cm/hr -1 to 1.80 cm.h-1, as well as for each of the air porosity by (89) % and the volume of infiltrate water by (40) %, compared with the control. The above-mentioned addition also resulted in a decrease in both dry bulk density, total soil porosity and volumetric swelling coefficient by (18.60, 5.80, 314) % Respectively, compared to the control. The addition also contributed to the reduce in the weighted moisture content when saturation and the field capacity, at the level of significance of 5%. The research recommends adding volcanic ash to the soil at a quantity of 5%, and adding enhancements with volcanic ash at various levels such as organic waste.

The present work studies a swelling porous-elastic system with viscoelastic damping. We establish a general and optimal decay estimate which generalizes some recent results in the literature. Our result is established without imposing the usual equal-wave-speed condition associated with similar problems in literature.

We report on the successful preparation of wet dressings hydrogels based on Chitosan-Poly(N-Vinyl-Pyrrolidone)-Poly(ethylene glycol)-Poly(acrylic acid) and Poly(ethylene oxide) by e-beam cross-linking in weakly acidic media, to be used for rapid healing and pain release of infected skin wounds. The structure and compositions of hydrogels investigated according to sol-gel and swelling studies, network parameters, as well as FTIR and XPS analyses showed the efficient interaction of the hydrogel components upon irradiation, maintaining the bonding environment while the cross-linking degree increasing with the irradiation dose and the formation of a structure with the mesh size in the range 11-67 nm. Hydrogels with gel fraction above 85% and the best-swelling properties in different pH solutions were obtained for hydrogels produced with 15 kGy. The hydrogels are stable in the simulated physiological condition of an infected wound and show appropriate moisture retention capability and the water vapor transmission rate up to 272.67 g m-2 day-1, to ensure fast healing. The hydrogels proved to have a significant loading capacity of ibuprofen (IBU), being able to incorporate a therapeutic dose for the treatment of severe pains. Simultaneously, IBU was released up to 25% in the first 2h, having a release maximum after 8h.

Expansive soil shows dual swell-shrink which is not suitable for the construction. Several mitigating techniques exist to counteract the problem promulgate by expansive clayey soils. This paper explored the penitential mecho-chemical reinforcement of expansive clayey soil to mitigate the effect of upward swelling pressure and heave. The polypropylene fiber is randomly distributed in the soil for mechanical stabilization, and the industrial residual silica fume is used as a chemical stabilizer. The experimental analysis is made in three phases which involved the tests on mechanical reinforced expansive soil using randomly distributed polypropylene fibers with different percentages (0.25%, 0.50%, and 1.00%), and 12mm length. The second phase of experiments carried out on chemical stabilized expansive soil with different percentages (2%, 4% and 8%) of silica and next phase of the experimental focused in the combination of mecho-chemical stabilization of the expansive soil with different combination of silica (i.e., 2%, 4% and 8%) and polypropylene fibers (i.e., 0.25%, 0.50% and 1.00%). Maximum dry density (MDD), optimum moisture content (OMC), liquid limit (LL), plastic limit (PL), plastic index (PI) grain size, and constant volume swelling pressure test were performed on unreinforced and reinforced expansive soil to investigate the effect of polypropylene fiber and silica fume on the engineering properties of expansive clayey soil. The experimental results illustrate that the inclusion of polypropylene fiber has a significant effect on the upward swelling pressure and expansion property of expansive soil. The reduction in the upward swelling pressure and expansion is a function of fiber content. These results also indicated that the use of silica fume caused a reduction in upward swelling potential, and its effect was considerably more than the influence of fiber.

This study was conducted to explore the potential of superabsorbent polymers (SAPs) from used disposable diapers as soil moisture conditioner. Swelling behavior of the proposed hydrogel in response to external stimuli such as salt solutions, temperature and pH was studied. In addition, laboratory experiments were carried out to evaluate the effects of incorporation hydrogel on germination of bean (Phaseolus vulgaris L.) and pumpkin (C. pepo) seeds. The structure of the superabsorbent was characterized by Fourier transform infrared spectroscopy (FTIR). The results indicate that the proposed SAP exhibited a maximum swelling capacity of 189 g.g-1 of dry gel. It was observed that the swelling capacity decreased with an increase in the ionic strength of the swelling medium. When this SAP was mixed with sandy soil, the mixture was able to lose water more slowly. The seeds germination and seedling growth was remarkably influenced by the application of 0.5, 1.0 and 2.0 w/w% of SAP compared to the untreated soil. Therefore, it follows that it is possible to take advantage of SAPs property from used disposable diapers to retain the moisture in soil as an alternative to value the use of such waste, showing that it has potential for diverse applications in agriculture.

Studies on the long-term stability of meat analogs stored under frozen conditions are lacking. Here, we aimed to assess the storage stability of vegetable oil-supplemented meat analogs and analyze the effects of temperature and storage period on their physiochemical characteristics. The meat analogs were prepared by adding 30 g castor oil, orange oil, palm oil, shortening, or margarine vegetable oil based on 100 g of textured vegetable protein. They were then stored at −18 or −60 °C for 6 months and analyzed at one-month intervals. The meat analog supplemented with orange oil had the highest water content, liquid-holding capacity, hardness, and antioxidant activity. During frozen storage, temperature barely affected the meat quality. The storage stability of all meat analog samples was maintained for 6 months, although the quality was slightly reduced with an increase in storage duration. Coliform group bacteria were not detected regardless of the storage condition. Orange oil improved the juiciness of meat analogs, and the quality of samples was maintained for at least 6 months under frozen storage. The findings of this study are relevant to the development and promotion of vegetable meat as an alternative to animal meat.

Concentration and preservation of lactic acid bacteria (LAB) starter cultures for food production guarantee the long-term delivery of stable cultures in terms of viability and functional activity. One method that has commonly been used to prepare dried starter cultures for food applications is freeze-drying. During freeze-drying, the bacterial cells are exposed to stresses such as freezing, drying, and long-term exposure to low-water activity. Additionally, another added stress is introduced during the rehydration process. The purpose of this study was to evaluate the survival rates and fermentation performance of three (3) freeze-dried lactic acid bacterial cultures previously isolated from Ghanaian traditional fermented milk. LAB cultures, i.e., Lactobacillus delbrueckii, Lactococcus lactis and Leuconostoc mesenteroides were frozen in the chamber of a Telstar (Lyoquest) laboratory freeze dryer for 10 hrs at -55 °C (as single and combined cultures) using skimmed milk and cassava flour as cryoprotectants held in plastic or glass cryovial. For viability during storage, freeze-dried LAB cultures were stored in a refrigerator (4 °C) and at room temperature (25 °C) for 4-weeks. The survival of freeze-dried cultures was determined by growth kinetics at 600nm (OD₆₀₀). The performance of freeze-dried LAB cultures after 4-weeks storage was determined by their growth and acidification of milk during yogurt fermentation and consumer sensory evaluation of fermented milk using a 9-point hedonic scale. The survival rates for LAB ranged between 60.11% and 70.91% following freeze-drying. For single cultures, the highest survival was recorded for Lactobacillus delbrueckii (L12), whereas for combined cultures, the highest survival was observed for Lactococcus lactis (L3) combined with Lactobacillus delbrueckii (L12). During the fermentation process all the freeze-dried LAB cultures were able to acidify yogurt to a pH below 4, while yogurt produce from the spontaneous fermentation was characterized by low acidification. Yogurt fermented with freeze-dried lactic acid bacteria cultures, either single or combined strains, showed improved acceptability as compared to the spontaneously fermented yogurt. The consumer acceptability results showed that yogurts produced with combined starter culture of Lactoccus lactis and Lactobacillus delbrueckii or single culture of Lactococcus lactis were the most preferred products with Lactococcus lactis and Lactobacillus delbrueckii possessing high survival rates and high consumer acceptability in yogurt production. These findings are crucial and can be adopted for large-scale production and commercialization of yogurt production, however, in-depth investigation on the effects of freeze-drying and long-term storage on survival and performance of selected LAB cultures are needed.

One of the operational challenges for the use of bentonite pellets as a sealing material in the abandonment of offshore fields consists in their disposition inside the well. This study aims to analyze the interaction of fluid media, consisting of saline solutions (NaCl, CaCl2 and KCl) and organic compounds (diesel, glycerin and olefin), with bentonite pellets, aiming its application as displacement fluid in offshore oil well abandonment operations. The physical integrity of the bentonite pellets in contact with the fluids was verified through visual inspections and dispersibility tests. Linear swelling tests were also performed to evaluate the potential for swelling of pellets in deionized water after contact with the fluid media. The results indicated that NaCl, CaCl2 and KCl solutions completely compromise the physical integrity of the pellets, while diesel and olefin showed the best responses regarding the structural preservation. Futhermore, the linear swelling tests showed that, even after the contact with diesel and olefin for 1 hour, bentonite pellets have reached a total swelling in water of 78%, after 24 hours. In this way, diesel and olefin proved to be highly promising alternatives to be used as displacement fluids for bentonite pellets in wells to be abandoned in a submarine environment.

Butyl rubber-based composite (BRC) is one of the most popular materials for the fabrication of protective glove against chemical and mechanical risks. However, in many working places such as metal manufacturing or automotive mechanical services, its mechanical hazards usually appear together with metalworking fluids (MWFs). The presence of these contaminants, particularly at high temperature, could modify its properties due to the scission, the plasticization, the crosslinking of polymer network and thus led to severe modification of mechanical and physicochemical properties of material. This work aims to determine the effect of temperature and a metalworking fluid on mechanical behavior of butyl rubber composite dealing with crosslinking density, cohesion forces and elastic constant of BRC on the based on Mooney-Rivlin’s theory. The effect of temperature with and without MWFs on thermo dynamical properties and morphology of butyl membranes is also investigated. The prediction of service lifetime is then evaluated from extrapolation of Arrhenius plot at different temperatures.

Artificial regeneration is successful when high performing seedlings are transported with care to the planting site, stored for a short period in an environment without desiccation or fungal growth, and are planted in a deep hole so roots are in contact with moist soil. One of the requirements for success is the ability to avoid common planting mistakes. Due, in part, to use of container stock plus an increase in rainfall, average 1st year survival of pine seedlings (89%) in the southern United States is about 15% greater now than 45 years ago. However, when survival is less than 50% six months after planting, some landowners seek reimbursement for their loss. Some assume poor seedling quality was the cause without realizing that anaerobic soils or sudden freeze events or shallow planting holes or pruning roots, a lack of rain, or underground insects can kill pines. With a focus on pines planted in the southern United States, we list non-nursery factors that have killed seedlings in North America, Africa and Europe.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

This study investigated the effects of freeze-thaw cycles on the mechanical properties of hardened self-compacting concrete for varying column heights. A column (100×20×300 cm) was fabricated by C30 self-compacting concrete in the laboratory and 10 cube samples (10x10x10 cm) were taken from fresh concrete as the references. After a period of 28 days, 160 core specimens (Ø67 mm in diameter) were taken from different column heights. Unit weight, water absorption, compressive strength, and freeze-thaw tests were performed on these 170 (10 reference cubic and 160 core) samples. The mechanical properties of the core specimens before freeze-thaw and after 8-56 freeze-thaw cycles were reported for varying column heights. The average compressive strength value of the reference cubic samples was determined as 40.28 MPa, while the compressive strengths of the core specimens before freeze-thaw were ranged from 40.25 MPa to 49.62 MPa, impying an increase in compressive strength values up to 23.18% compared to the reference cubic samples. Compressive strengths of the specimens subjected to 8 and 56 freeze-thaw cycles varied between 38.71‒48.07 MPa and 31.72‒39.11 MPa, respectively. Statistical analysis revealed that the compressive strength of the concrete exposed to 56 freeze-thaw cycles was significantly different from that of the other specimens.

Sterilisation and preservation of vesicle formulations are an important consideration for their viable manufacture for industry applications, particular those intended for medicinal use. Here we undertake an initial investigation of the stability of hybrid lipid – block copolymer vesicles to common sterilisation and preservation processes, with particular interest in how the block copolymer component might tune vesicle stability. We investigate two sizes of polybutadiene-block-poly(ethylene oxide) polymers (PBd12-PEO11 and PBd22-PEO14) mixed with the phospholipid POPC considering the encapsulation stability of a fluorescent cargo and the colloidal stability of vesicle size distributions. We find that autoclaving and lyophilisation cause complete loss of encapsulation stability under the conditions studied here. Filtering through 200 nm pores appears to be viable for sterilisation for all vesicle compositions with comparatively low release of encapsulated cargo, even for vesicle size distributions which extend beyond the 200 nm filter pore size. Freeze-thaw of vesicles also shows promise for preservation of hybrid vesicles with high block copolymer content. We discuss the process stability of hybrid vesicles in terms of the complex mechanical interplay between bending resistance, stretching elasticity and lysis strain of these membranes and propose strategies for future work to further enhance the process stability of these vesicle formulations.

Antigen-based rapid diagnostic tests for Lymphatic filariasis do not come with quality control (QC) materials, and research and disease control programmes rely on stored positive plasma samples. This study was undertaken to evaluate the use of freeze-dried Wuchereria bancrofti antigen positive plasma samples to serve as QC materials for LF RDTs. 10 well characterized W. bancrofti positive samples were lyophilized and stored at 4°C, 28°C and 40°C. The samples were evaluated using the Filaria Test Strips before lyophilization and after one and three (3) months of storage. The sensitivity and stability of the lyophilized samples were evaluated. The results revealed a loss of sensitivity and stability with increasing temperature and duration of storage. The results are further discussed in terms of the use of Dried Blood Spot (DBS) in diagnostics studies on LF requiring quantitative assessments, and the need for thoughtful DBS preparation and storage.

Gelatin fibers have a specific surface and high porosity, which is why their use in medicine and the food industry is being researched. This article explores the potential of centrifugal spinning to produce gelatin fibers. Gelatin for fiber preparation is obtained from a non-traditional source of collagen (chicken by-products) using a unique enzymatic process. The fiber quality is compared with those prepared from traditional collagen tissues (porcine, bovine). The results show that fibers crosslinked with glutaraldehyde vapor preserve their structure even in contact with water. Using a cross-linker controls swelling ability and solubility while maintaining the fiber structure. On the contrary, uncross-linked gelatin fibers are water soluble due to a high surface-to-volume ratio, facilitating water penetration and dissolution. Scanning electron microscopy (SEM) provided a clearer picture of the morphology of gelatin fibers obtained by centrifugal spinning. Differences in the amount of bonding depending on the raw material used and the presence of cross-linker were analyzed using Fourier transform infrared spectroscopy (FTIR). The overall results showed that chicken gelatin is a suitable alternative to gelatins from traditional sources.

Modification of Scots pine sapwood (Pinus sylvestris L.) with heterocyclic compounds, imidazole and succinimide, was investigated. Pressure-impregnation with aqueous solutions containing imidazole, imidazole + citric acid, succinimide, succinimide + citric acid, and citric acid + sorbitol (CIOL®) at 5%, 10%, and 15% solid content was followed by oven-curing at 220 °C for 1 hour. Mass changes during treatment steps, bending properties, and anti-swelling efficiency (ASE) were examined. Results indicate that solid concentrations within the range of 5% to 10% were optimal. Results seem to show there are two differing mechanisms in the modification of imidazole and succinimide, respectively. Mass loss due to the heat treatment was highest in imidazole-treated specimens, whereas it remained low and concentration-independent in succinimide-treated specimens. ASE after three cycles reached 31% for imidazole-treated specimens and improved to 38% with the addition of citric acid. For succinimide, ASE increased from 17% to 41%. Bending properties generally showed improvement, except for succinimide + citric acid and CIOL®, which displayed a reduced modulus of rupture. Chemical analyses are warranted to fully understand the reaction mechanisms of the treatments. Imidazole treatment's positive effects are suggested to stem from a thermal reaction between the chemical and wood, indicated by substantial mass loss during leaching and specimen darkening. Succinimide and citric acid might exhibit polymerization with each other and wood components, akin to the CIOL® process. Further research should delve into reaction mechanisms and the impact of imidazole and succinimide on biological durability.

Lavander distillation leads to huge quantities of solid waste produced yearly. This waste is usually discarded resulting in serious environmental issues. However, it still contains residual essential oil and other bioactive compounds. This research reports on the development and comparison of optimized solid-liquid separation methods, i.e. microwave (MAE) and ultrasound assisted extraction (UAE) of phenolic compounds from lavender distillation waste. Optimal pretreatment conditions, such as waste moisture content and particle size were also determined. The extracts were spray or freeze-dried and the resulting powders were characterized for their physicochemical properties. The majority of the original phenolic compounds in lavender were found in the leachate fraction after distillation (61%), while 43% in the solid waste. Drying of the solid waste before extraction affected the process efficiency. UAE led to higher phenolic content and antioxidant properties compared to MAE. Drying (spray or freeze) the extracts did not significantly affect their phenolic content, while the use of maltodextrin as a drying agent improved the drying process yield especially in the freeze-drying method. It is concluded that valorization of lavender distillation wastes can be achieved via an integrated process consisting of a green extraction method and a consequent drying process that result in a stable bioactive powder.

Rising temperatures due to the climate change can significantly impact the frost/thaw condition of airport pavements in cold regions. This case study investigates the implications of the the warming temperatures on frost/thaw penetration and frost-heave of pavements for critical airports across Canada. To this end, different methods were used in the quantification process through climate change simulations considering the emission scenario RCP8.5 in a 20- and 40-year time horizon. The results show that climate change would have different design implications for airport pavements depending on their location. The predictions suggest a shallower frost penetration depth and possibly less frost-heave for the airports not underlain by permafrost, while airports over permafrost areas might experience an increase in thickness of the active layer ranging from 41 to 57 percent by 2061. Among the different methods used in this study, it was observed that some methods performed the best in predicting frost depth of fine soils, while others worked better with the frost depth prediction of coarse soils. The results indicate the need for more mechanistic models to provide a more realistic prediction of frost/thaw penetration as compared to the existing empirical models.

Immobilized metal ion affinity adsorbents have been widely used in separation technique to purify proteins. Due to the leakage of metal ion from the adsorbents, there is no metal ion affinity adsorbent for hemoperfusion has been applied to clinical trial. In this study, in order to prevent the leakage of Zn²⁺ loaded from cellulose beads based adsorbent, improve its stability and adsorption capacity for testosterone, Freeze-drying method was used to enhance the porosity of cellulose beads, improve the surface area of the cellulose beads and adsorption capacity for testosterone. Chitosan was used to coat the adsorbents for preventing the leakage of Zn²⁺ loaded and improve the adsorbent’s stability. Moreover, the factors affecting adsorption ability and some components in plasma were also investigated. The results indicate the adsorption ability of the adsorbent can be significantly improved by freeze-drying. After the adsorbent was coated with 0.02% chitosan solution, the highest adsorption percentage reached 48%. During adsorption, the Zn²⁺ concentration in plasma did not rise. In addition, the adsorption percentage for total proteins was below 15%. The results may be caused by the pore size and surface area of the adsorbent enlarged via freeze-drying, and the chitosan solution went into the pores and coated the outer and inner surface of the adsorbent. The adsorbent has a potential clinical application to remove testosterone in patients with recurrent and metastatic prostate cancer.

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Deterioration of concrete subjected to freezing and thawing climatic conditions is one of most important factors affecting the durability of concrete infrastructure in cold climates. The freeze-thaw resistance of cementitious materials like concrete and mortar can be determined by the CDF test (Capillary Suction of De-icing chemicals and Freeze-Thaw Test). Here, concrete specimens are subjected to repeated freeze-thaw cycles with simultaneous addition of de-icing salt and the amount of material weathered near the surface is determined. For concretes with adequate freeze-thaw resistance, this test method works very well. However, specimens with inadequate or unknown performance often experience increased edge weathering, which is caused by the detachment of the lateral isolation tape. The increasing edge influence thus leads to a falsification of the results and consequently to an underestimation of the actual freeze-thaw resistance of the material. In materials research in particular, however, concretes with high levels of weathering are studied in order to be able to investigate various factors of influence on the freeze-thaw resistance of concretes in a targeted manner. This paper presents a novel methodology that delivers new information regarding the weathering of CDF test samples and the associated distribution function of the height decrease using high resolution 3D scan data. The results indicate a correlation between the progression of the distribution function and the sample's maximum aggregate size. The change of the sample volume can be used to support the weathering results of the standard CDF methodology. The increase of the surface area is used to estimate the tortuosity of the sample surface. It indicates an asymptotic curve approaching a specific maximum value, which is dependent on the the weathering depth of the sample.

In Poland, the mountainous and hilly regions until recently were territories with unbalanced and poor diet quality, especially in early spring. Wild edible plants were or still are influential in supplementing a human diet. One of the earliest wild edible plants to appear in the growing season, characteristic of a broad swath of Europe from Ukraine to Germany, remains wild (bear) garlic (Allium ursinum L.). This paper assesses the impact of the vegetation site and preservation methods on selected parameters of the chemical composition of bear garlic. In addition, the connection between its genome pattern and chemical composition was assessed. The plants were collected in three locations in the Carpathian foothills, and the reference sample was plants collected in the lowlands. The site from which the raw material was harvested has a statistically significant effect on the chemical composition of the preserved leaves of bear garlic. The profiles of the analysed components differed in the material from a different site. Bear garlic leaves from mountainous areas had more analyzed components than those obtained from the lowland sites. Moreover, the material from the lowlands had a different genetic pattern from the leaves from the mountainous areas..

Wood has been used in the construction, furniture, and automotive industries since ancient times. In areas where wood material is used, it is combined with various fasteners. The durability of the products produced using wooden materials depends on the performance of the fasteners. Since wood is a hydroscopic and biodegradable material, various changes occur in its structure when exposed to external weather conditions. Wood materials used especially in the field of construction and urban furniture are exposed to effects such as extreme temperatures, freezing, moisture, or drying depending on the seasons. In this study, the effect of freeze-thaw cycling (FTC) process on screw direct withdrawal resistance (SDWR) of plywood produced from beech, ozigo, and okoume species was investigated. In this context, the effects of screwing time (before or after), screw orientation (face or edge), number of cycles (0 to 7) in the FTC process and plywood type parameters on SDWR were investigated. As a result of the tests, when the mean SDWR values were examined according to the plywood type, the highest values were obtained in beech, ozigo, and okoume plywood, respectively. Considering the screwing time parameter, it was determined that there was no statistically significant difference between the mean SDWR values in other plywood types except beech plywood (p<0.05). When the screw orientation parameter is examined, screwing in the face direction gave better results than screwing in the edge direction in all plywood types. There was a decrease in the mean SDWR values inversely proportional to the increase in the number of cycles in FTC-treated plywood.

Freeze-drying is a well-established process in biomedical engineering for the fabrication of three-dimensional open-porous medical devices, especially those based on biopolymers. One of the most used biopolymers in this field is collagen, the most abundant protein in the human body and the main component of the extracellular-matrix, as well as its derivatives. Freeze-dried collagen-based sponges with a wide variety of attributes can be produced by design and have led to a wide range of successful commercial medical devices, foremost for dental, orthopedic, hemostatic and neuronal applications. However, this is still considered a high-cost and time-consuming process that is often used in a non-optimized manner. By combining advances in other technological fields, the opportunity arises to further evolve this process in a sustainable manner, and optimize the resulting products as well as create new opportunities in this field.

Silty clay modified by fly ash and crumb rubber is a kind of sustainable subgrade filler which has good anti-freeze-thaw resistance stability but wake vibration isolation performance. The objective of this study was to improve the vibration isolation of the modified soil and investigate the vibration isolation effect of the composite subgrade structure of XPS plates and the modified soil by indoor impact test. First, the vibration isolation performance of silty clay, modified soil and composite subgrade structure was respectively evaluated. Second, the effect of XPS plate’s thickness and vibration intensity on the vibration performance of the composite subgrade structure were evaluated. Third, the vibration isolation performance of the test groups under the condition of freeze-thaw cycles was assessed. The results show that the vibration isolation performance of subgrade can be effectively improved by setting XPS plates. The composite subgrade structure has certain vibration isolation effect, especially in vertical direction. Considering vibration isolation performance and costs, 5cm is the optimum XPS plates thickness. The composite subgrade structure has great vibration isolation performance under the condition of freeze-thaw cycles, so it is suitable to be applied in road subgrade in seasonal frozen regions.

A portable, electrical impedance spectroscopy device to monitor the bioimpedance’s resistive component of beef meat by injecting a sinusoidal current of 1mA at 65.5 kHz was developed. In 4 slaughtered beef both right and left longissimus dorsi muscles where trimmed and left muscle portion was frozen to -18° C up to 7^th day while right one was meantime maintained at 5° C. Median value of specific resistivity of not-frozen sample was about twice Ω cm^-1 with respect of that of frozen-thawed sample (P = 0.004). It was concluded that the device is reliable to monitoring the ripening of beef meat in situ.

Geopolymer concrete (GPC) represents an innovative green and low-carbon construction material, offering a viable alternative to ordinary Portland cement concrete in building applications. However, existing studies tend to overlook the recyclability aspect of GPC for future use. Various structural applications necessitate the use of concrete with distinct strength characteristics. The recyclability of the parent concrete is influenced by these varying strengths. This study examined the recycling potential of GPC across a spectrum of strength grades (40, 60, 80 and 100 MPa, marked as C40, C60, C80 and C100) when subjected to freeze-thaw conditions. The cementitious material comprised 60% metakaolin and 40% slag, with natural gravel serving as the coarse aggregate, and the alkali activator consisting of sodium hydroxide solution and sodium silicate solution. The strength of the GPC was modulated by altering the Na/Al ratio. After 350 freeze-thaw cycles, the GPC specimens underwent crushing, washing, and sieving to produce recycled geopolymer aggregates (RGAs). Subsequently, their physical properties and microstructure were thoroughly examined. The findings indicated that GPC with strength grades of C100, C80, and C60 were capable of enduring 350 freeze-thaw cycles, in contrast to C40, which did not withstand these conditions. RGAs derived from GPC of strength grades C100 and C80 complied with the criteria for Class II recycled aggregates, whereas RGAs produced from GPC of strength grade C60 aligned with the Class III level. A higher strength grade in the parent concrete correlated with enhanced performance characteristics in the resulting recycled aggregates.

This study is focused on the experimental investigation of compressive strength and durability properties of lightweight concrete mixtures with fine expanded glass and expanded clay aggregates using different microfillers. The paper proposes the relationships between the compressive strength and density of concrete mixtures with different proportions of lightweight aggregates mentioned above. The performed experimental studies have revealed the tendencies of possible usage of different amount of fine lightweight aggregates and their combinations in the production of concrete mixtures depending on the demands of practical application. Following the requirements for structural concrete subjected to environmental effects, durability properties (alkaline corrosion and freeze–thaw resistance) of the selected concrete mixtures with expanded glass aggregate were studied. The results of the experimental investigations have shown that durability of tested concrete specimens was sufficient. The study has concluded that the mixtures under consideration can be applied for the production of structural elements to which durability requirements are significant.

Microencapsulation of polyherbal formulation (PHF) extract was carried out by freeze drying method, by employing gum arabic (GA), gelatin (GE), and maltodextrin (MD) with their designated different combinations as encapsulating wall materials. Antioxidant components (i.e total phenolic contents (TPC),Total flavonoids contents (TFC), and total condensed contents (TCT)), antioxidant activity (i.e. DPPH, β-carotene & ABTS⁺ assays), moisture contents, water activity (aw), solubility, hygroscopicity, glass transition temperature (T_g), particle size, morphology, in vitro alpha-amylase and alpha-glucosidase inhibition and bioavailability ratios of the powders were investigated. Amongst all encapsulated products, T_B (5% GA and 5% MD) and T_C (10% GA) has proven to be the best treatments with respect to the highest preservation of antioxidant components and their antioxidant potential by DPPH and β-carotene assays and noteworthy for an ABTS⁺ assays, in addition, the aforesaid treatments also demonstrated lower moisture content, aw, particle size and higher solubility, hygroscopicity and glass transition temperature (T_g). All freeze dried samples showed irregular (asymmetrical) microcrystalline structures. Furthermore, T_B and T_C also illustrated the highest in vitro anti-diabetic potential due to great potency for inhibiting alpha-amylase and alpha-glucosidase activities. In the perspective of bioavailability, T_A, T_B and T_C demonstrated the excellent bioavailability ratios (%).Futhermore, the phytochemo-profiling of ethanolic extract of PHF was also revealed to find out the bioactive compounds.

A technique for fabrication of bacterial cellulose-based films with CeO₂ nanofiller has been developed. The structural and morphological characteristics of the materials have been studied, their thermal and mechanical properties in dry and swollen states having been determined. The preparation methodology makes it possible to obtain composites with a uniform distribution of nanoparticles. The catalytic effect of ceria regarding the thermal oxidative destruction of cellulose has been confirmed by TGA and DTA methods. An increase in CeO₂ content led to an increase in the elastic modulus (a 1.27-fold increase caused by the introduction of 5 wt.% of the nanofiller into the polymer) and strength of the films. This effect is explained by the formation of additional links between polymer macro-chains via the nanoparticles’ surface. The materials fabricated were characterised by a limited ability to swell in water. Swelling caused a 20- to 30-fold reduction in the stiffness of the material, the mechanical properties of the films in a swollen state remaining germane to their practical use. The application of the composite films in cell engineering as substrates for the stem cells’ proliferation has been studied. The increase in CeO₂ content in the films enhanced the proliferative activity of embryonic mouse stem cells. The cells cultured on the scaffold containing 5 wt.% of ceria demonstrated increased cell survival and migration activity. An analysis of gene expression confirmed improved cultivation conditions on CeO₂-containing scaffolds.

A three-arm, randomized, placebo controlled clinical study has been performed to evaluate the effects of a lyophilized pineapple extract titrated in bromelain (Brome-Inf®), and purified bro-melain on pain, swelling, trismus and quality of life (QoL) after the surgical removal of the lower third molars. Moreover, the need for non-steroidal anti-inflammatory drugs (NSAIDs) has also been evaluated and compared with a placebo group. The study included 42 people that required the extraction of a single mandibular third molar under local anesthesia. The patients were ran-domized and distributed to receive Brome-Inf®, purified bromelain or placebo and started the treatment the day of surgery and continued it for the next 7 days. The primary outcome was the requirement of NSAIDs in the three groups. The outcome variables were pain, swelling and trismus, which were measured postoperatively at 1, 3, and 7 days. The differences in the efficacy of the freeze-dried pineapple extract and single-component bromelain were also evaluated. At the end of the study, the assumption of ibuprofen (from days 1-7) was statistically higher in the placebo group (p

Freezing of Gait (FOG) is an impairment that affects the majority of patients in the advanced stages of Parkinson’s Disease (PD). FOG can lead to sudden falls and injuries, negatively impacting the quality of life for the patients and their families. Rhythmic Auditory Stimulation (RAS) can be used to help patients recover from FOG and resume normal gait. RAS might be ineffective due to the latency between the start of a FOG event, it’s detection and initialization of RAS. We propose a system capable of both FOG prediction and detection using signals from tri-axial accelerometer sensors that will be useful in initializing RAS with minimal latency. We compared the performance of several time frequency analysis techniques, including moving windows extracted from the signals, handcrafted features, Recurrence Plots (RP), Short Time Fourier Transform (STFT), Discreet Wavelet Transform (DWT) and Pseudo Wigner Ville Distribution (PWVD) with Deep Learning (DL) based Long Short Term Memory (LSTM) and Convolutional Neural Networks (CNN). We also propose three Ensemble Network Architectures that combine all the time frequency representations and DL architectures. Experimental results show that our ensemble architectures significantly improve the performance compared with existing techniques. We also present the results of applying our method trained on publicly available dataset to data collected from patients using wearable sensors in collaboration with A.T. Still University.

Alpine forest gaps can distribute snowfall, solar radiation and rainfall, thus inducing a heterogeneous hydrothermal microenvironment between the inside and outside areas of forest gaps. Additionally, the characteristics of the heterogeneous microenvironment could vary greatly across the gap location properties during winter and the growing season. To determine the response of total phenol loss (TPL) from the litter to alpine forest gap disturbance during decomposition, we conducted a field litterbag experiment within a representative fir (Abies faxoniana Rehd.) forest based on the gap location properties. The TPL and abundances of fungi and bacteria from two typical shrub species (willow, Salix paraplesia Schneid., and bamboo, Fargesia nitida (Mitford) Keng f.) were measured during the following periods over two years: snow formation (SF), snow cover (SC) snow melting (ST), the early growing season (EG) and the later growing season (LG). At the end of the study, we found that the snow cover depth, frequencies of the freeze-thaw cycle and the fungal copy g-1 to bacterial copy g-1 ratio had significant effects on the litter TPL. The abundances of fungi and bacteria decreased from the gap center to the closed canopy during the two SF, SC, ST and LG periods and reversed during the two EG periods. The TPL closely followed the same trend as the microbial abundance during the first year of incubation. In addition, both species had larger TPLs in the gap center during the first winter, first year and entire two years. These findings suggest that alpine forest gap formation accelerates litter TPL and plays a dual role during specific critical periods by distributing abiotic and biotic factors directly and indirectly. In conclusion, reduced snow cover depth and duration during winter warming under current climate change scenarios or as gaps vanish may slow litter TPL in alpine biomes.

It remains unclear in the literature what is the cause of the so-called alkali-carbonate reaction (ACR) damage to concrete yet, a consensus is reached when considering dedolimitization as non-expansive. However, expansion and cracks as distress features are often attributed to alkali-silica reaction (ASR) when evidence of a reactive mineral is found in the aggregate. Evidently, different types of aggregates may produce different types and degrees of damage. Therefore, this work aims to assess the damage to concrete generated and propagated by the so-called ACR susceptible reactive Kingston coarse aggregate through mechanical testing (i.e., direct shear test), microscopy (the damage rating index – DRI), and other techniques. Distinct induced expansion levels (i.e., 0%, 0.05%, 0.12%, and 0.20%) were selected to compare the distress caused by ACR to concrete affected by ASR. Result show that the behaviour of ACR, namely as captured through the DRI, is inconsistent with that of ASR thus attesting to ACR being a distinct distress mechanism.

The cosmological relevance of emptiness—that is, space without bodies—is not yet sufficiently appreciated in natural philosophy. This paper addresses two aspects of cosmic emptiness from the perspective of natural philosophy: the distances to the stars in the closer cosmic environment and the expansion of space as a result of the accelerated expansion of the universe. Both aspects will be discussed from both a historical and a systematic perspective. Emptiness can be interpreted as “coming” in a two-fold sense: Whereas in the past knowledge of emptiness as it were came to human beings, in the future it is coming insofar as its relevance in the cosmos will increase.The longer and more closely emptiness was studied since the beginning of modernity, the larger became the spaces over which it was found to extend. From a systematic perspective, I will show with regard to the closer cosmic environment that the earth may be separated from the perhaps habitable planets of other stars by an emptiness that is inimical to life and cannot be traversed by humans. This assumption is a result of the discussion of the constraints and possibilities of interstellar space travel as defined by the known natural laws and technical means. With the accelerated expansion of the universe, the distances to other galaxies (outside of the so-called local group) are increasing. According to the current standard model of cosmology and assuming that the acceleration will remain constant, in the distant future this expansion will lead first to a substantial change in the epistemic conditions of cosmological knowledge and finally to the completion of the cosmic emptiness and of its relevance, respectively. Imagining the postulated completely empty last state leads human thought to the very limits of what is conceivable.

Porous β-tricalcium phosphate (Ca3(PO4)2; β-TCP) was prepared by freeze-drying and the effects of this process on pore shapes and sizes were investigated. Various samples were prepared by freezing β-TCP slurries above a liquid nitrogen surface at −180 °C with subsequent immersion in liquid nitrogen at −196 °C. These materials were then dried under reduced pressure in a freeze-dryer after which they were sintered by heating. Compared with conventional heat-based drying, the resulting pores were more spherical, which increased both the mechanical strength and porosity of the β-TCP. These materials had a wide range of pore sizes from 50 to 200 µm, with the mean and median values both approximately 100 µm regardless of the freeze-drying conditions. Mercury porosimetry data showed that the samples contained small, interconnected pores with sizes of up to 1.24 µm and macroscopic, interconnected pores up to 25.8 µm in size. The effects of non-ionic surfactants having different hydrophilic/lipophilic balance (HLB) values on foaming and pore size were also investigated. Materials made with surfactants having lower HLB values exhibited smaller pores and lower porosity whereas higher HLB surfactants gave higher porosity and slightly larger macropores. Even so, the pore diameter could not be readily controlled solely by adjusting the HLB value. The findings of this work indicated that high porosity (75%) and good compressive strength (>2 MPa) can both be obtained in the same porous material and that foaming agents with HLB values between 12.0 and 13.5 were optimal.

To compare concentrations of endogenous N-acylethanolamines (NAEs) lipid mediators pal-mitoylethanolamide (PEA), oleoylethanolamide (OEA), and anandamide (AEA) in fresh, decon-taminated, cryopreserved and freeze-dried amniotic membrane (AM) allografts. Thereby deter-mining whether AM's analgesic and anti-inflammatory efficiency related to NAEs persists during storage. The concentrations of NAEs were measured using ultra-high-performance liquid chro-matography-tandem mass spectrometry. Indirect fluorescent immunohistochemistry was used to detect the PEA PPARα receptor. The concentrations of PEA, OEA, and AEA were significantly higher after decontamination. A significant decrease was found in cryopreserved AM compared to decontaminated tissue for PEA but not for OEA and AEA. However, significantly higher val-ues for all NAEs were detected in cryopreserved samples compared to fresh tissue before decon-tamination. The freeze-dried AM had similar values to decontaminated AM with no statistically significant difference. The nuclear staining of PPARα receptor was clearly visible in all specimens. The stability of NAEs in AM after cryopreservation was demonstrated under tissue bank storage conditions. However, a significant decrease, but still higher concentration of PEA compared to fresh not decontaminated tissue was found in cryopreserved, but not frieze-dried AM. Results in-dicate that NAEs persist during storage in levels sufficient for the analgesic and anti-inflammatory effects of AM allografts.

Concrete is the most commonly used construction material due to its various advantages, such as versatility, familiarity, strength and durability and it will continue to be in demand far into the future. However, with today’s sensitivity to the environmental protection, this material is facing unprecedented challenges due to its high greenhouse gas emission mainly during cement production. This paper investigates one of the promising cement replacement materials, alkali activated cement (AAC) concrete. Being produced mainly from byproduct materials and having a comparable structural performance to conventional concrete, AAC concrete has a potential to transform the construction industry. Mechanical properties such as compressive and flexural strength and the relationship between them are studied. Different source materials such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF) and Metakaolin (MK) are used. The effect of the source materials and the activator solutions on the concrete performance is studied. Furthermore, the freeze-thaw resistance of the concrete is studied. The results of the study showed that the behavior of AAC depends highly on the source material combinations as well as type used. The effect of the alkaline solution is also dependent on the source material used. Mixes with higher GGBS content in general showed the highest strength while mixes with MK showed the highest flexural strength. The results from the freeze-thaw test showed that proper design of AAC concrete with a lower water content is critical to achieve a good resistance.

Hardened air void analysis provides essential information of concrete freeze-thaw durability based on the size and spacing of air voids in the material. As the physical freeze-thaw experiment is time-consuming and costly, the characteristics of concrete air voids are often deemed as a proxy of the freeze-thaw performance. This analysis is typically done by measuring the 2D air void intersections on polished samples, but the current interpretation of the 2D void characters does not accurately represent the actual void structure in 3D. To solve this problem, a 2D-to-3D unfolding technique has been proposed in the field of stereology. However, the unfolding analysis is known to be sensitive to several factors, such as void population and size along with a binning scheme, where improper unfolding can considerably bias the prediction of the actual concrete void system. This study investigates the optimal strategy of conducting the unfolding analysis for concrete. The investigation is carried out on both idealized void systems to interrogate the influence of the critical factors individually, and real concrete samples with varying levels of air entrainment to assess the concrete-specific impacts. The concrete void system is studied based on a stereological model emulating the intersected 3D air voids on the surface of polished concrete. The results highlight that, for unfolding concrete voids, logarithmic binning scheme is far more accurate to linear binning. The low unfolding error of the concrete samples indicates that the proposed methodology enables an accurate restoration of 3D void size distribution.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

Transverse momentum spectra of +, p, Λ, Ξ or ¯Ξ+, Ω or ¯Ω+ and deuteron (d) in different centrality intervals in Gold-Gold (Au-Au) and Lead-Lead (Pb-Pb) collisions at 62.4 GeV and 2.76 TeV respectively, are analyzed by the blast wave model with Boltzmann Gibbs statistics. We extracted Kinetic freeze out temperature,transverse flow velocity and kinetic freezeout volume from the transverse momentum spectra of the particles. It is observed that the non-strange and strange (multi-strange) particles freezeout separately due to different reaction cross-sections. While the freezeout volume and transverse flow velocity are mass dependent which decrease with the rest mass of the particles. The present work reveals the scenario of double kinetic freezeout in collisions at STAR and ALICE Collaborations. Furthermore, the kinetic freezeout temperature and freezeout volume are larger in central collisions than the peripheral collisions and they decrease from central to periphery. However the transverse flow velocity remains almost unchanged from central to peripheral collisions.

In the seasonally frozen regions, during the grouting of prestressed bridge ducts in low-temperature environments, incompletely cured grout materials undergo volumetric changes due to the freeze-thaw cycling, resulting in structural cracks along the prestressing ducts of the bridge, thereby diminishing the bridge's operational lifespan. To investigate the frost heaving characteristics of grout materials under freeze-thaw cycles and propose potential enhancements, this study was devised to conduct frost heaving stress tests on grout materials. Through this research, we gained insights into how various additives affect the frost heaving stress characteristics of grout materials under freeze-thaw cycles. Incorporating analyses of free water content, setting time, compressive strength, as well as macroscopic examinations such as XRD and SEM, this study delves into the mechanisms for enhancing frost heaving characteristics of grout materials. Furthermore, it proposes a research approach that utilizes multiple admixtures to improve the frost heaving properties of grout materials. Through frost heaving stress tests and other macroscopic experiments, the study investigates the influence of these combined admixtures on frost heaving stress in grout materials and elucidates the underlying improvement mechanisms. The results indicate that reducing the water-cement ratio, incorporating calcium formate, sulfoaluminate cement, air-entraining agents, and carbamide all have a positive impact on mitigating frost heaving stress in grout materials. However, the improvement mechanisms differ, and employing a single measure alone is insufficient to effectively reduce frost heaving stress while meeting performance criteria such as compressive strength, setting time, and flowability. Free water content emerges as a crucial indicator determining the magnitude of frost heaving stress in grout materials, with 11.5% of free water content representing the critical threshold for frost heaving in grout materials. Utilizing composite admixtures can simultaneously decrease free water content, lower the freezing point of free water, and alleviate frost heaving deformation, resulting in more efficient reduction of frost heaving stress. When the admixture content reaches 9.9%, frost heaving stress is eliminated, and the comprehensive performance parameters including compressive strength, setting time, and flowability meet the specified requirements.

Abstract: Thermostability of vaccines, particularly enveloped viral vectored vaccines, remains a challenge for their delivery wherever needed. Freeze-drying of viral vectored vaccines is a prom-ising approach but remains challenging due to the water removal process from the outer and in-ner parts of the virus. In the case of enveloped viruses, freeze-drying induces increased stresses on the envelope, which often leads to inactivation of the virus. In this study, we design a method to freeze-dry a recombinant Vesicular Stomatitis Virus (VSV) expressing the SARS-CoV-2 spike glycoprotein. Since the envelope of VSV is composed of 50% lipid and 50% protein, the formula-tion study focused on both the protein and lipid portions of the vector. Formulations were pre-pared primarily using sucrose, trehalose, and sorbitol as cryoprotectants; mannitol as a lyopro-tectant; and histidine as a buffer. Initially, the infectivity of rVSV-SARS-CoV-2 and cake stability were investigated at different final moisture contents. High recovery of the infectious viral titer ( 0.5 to 1 log loss) was found at 3-6% moisture content with no deterioration of the freeze-dried cakes. To further minimize infectious viral titer loss, the composition and concentration of the ex-cipients were studied. An increase from 5 to 10% of both cryoprotectants and lyoprotectant, to-gether with the addition of 0.5% gelatin, resulted in the improved recovery of infectious virus titer and stable cake formation. Moreover, the secondary drying temperature of the freeze-drying pro-cess showed a significant impact on the infectivity of rVSV-SARS-CoV-2. The infectivity of the vector declined drastically when the temperature was raised above 20°C. Throughout a long-term stability study, formulations containing 10% sugar (sucrose/trehalose), 10% mannitol, 0.5% gelatin, and 10 mM of histidine showed satisfactory stability for six months at 2-8°C. The development of this freeze-drying process and the optimized formulation minimizes the need for a costly cold chain distribution system.