This study explores the potential of titanium disulfide (TiS2) as an active material for aqueous calcium-ion batteries (CIBs). We investigate the electrochemical redox reactions of calcium ions within TiS2 and assess its suitability for use in aqueous CIBs. Additionally, we examine the im-pact of different electrolyte concentrations on TiS2 electrode reactions. Our findings reveal that TiS2 exhibits distinct charge-discharge behaviors in various aqueous calcium-ion electrolytes. Notably, at higher electrolyte concentrations, TiS2 effectively suppresses the hydrogen genera-tion reaction caused by water decomposition, demonstrating its potential as an active material for aqueous CIBs. In-situ X-ray diffraction analysis confirms the intercalation of Ca2+ ions be-tween TiS2 layers during charging. This confirmation is groundbreaking, as it represents the first experimental evidence of calcium ions being electrochemically inserted between TiS2 layers from aqueous solutions, signifying a previously unreported achievement and strongly suggesting TiS2's applicability in aqueous CIBs. X-ray photoelectron spectroscopy analysis further supports the formation of a solid electrolyte interphase (SEI) on the TiS2 electrode surface, contributing to the suppression of electrolyte decomposition reactions. Furthermore, we investigate the influ-ence of anions in the electrolyte on charge-discharge behavior. Our findings suggest that the choice of anion coordinated with Ca2+ ions affects SEI formation and cycling performance. Un-derstanding the role of anions in SEI formation is crucial for optimizing aqueous CIBs. In con-clusion, this research underscores TiS2's potential as an active material for aqueous calcium-ion batteries and emphasizes the importance of electrolyte composition in influencing SEI formation and battery performance. These findings contribute to the development of more sustainable and efficient energy storage technologies.

During submerged laser peening using a pulsed laser, a bubble that behaves like cavitation is generated after laser ablation (LA). The bubble is referred to as laser cavitation (LC). The amplitude of the shock-wave in LA water is larger than that of LC; however, the impact passing through the target metal during LC is larger than that of LA. Thus, submerged laser peening is referred to as “laser cavitation peening”, as the peening method using the cavitation impact is known as “cavitation peening”. The impact induced by a hemispherical bubble is more aggressive than that of a spherical bubble with a microjet. Laser cavitation peening can improve the fatigue strength of metallic materials by producing work-hardening and the introduction of compressive residual stress. Three-dimensional additive manufactured metals (3D metals) such as titanium alloy are attractive materials for aviation components and medical implants; however, the fatigue strength of as-built components is nearly half that of bulk metals, and this is an obstacle for the applications of 3D metals. In the present study, published research papers were reviewed to identify the key factors of laser cavitation peening, with additional visualization of LC and data. Then, improvements in the fatigue strength of metallic materials, including 3D metals produced by laser cavitation peening, were summarized.

Microalloying of low carbon steel with niobium (Nb) and titanium (Ti) is standardly applied in high-strength low-alloy (HSLA) steels enabling austenite conditioning during thermo-mechanical controlled processing (TMCP), which results in pronounced grain refinement in the finished steel. The metallurgical effects of microalloying elements are related solute drag and precipitate particle pinning, both acting on the austenite grain boundary thereby delaying or suppressing recrystallization of the deformed grain. In that respect it is important to better understand the precipitation kinetics as well as the precipitation sequence in a typical Nb-Ti-microalloyed steel. Various characterization methods have been utilized in this study for tracing microalloy precipitation after simulating different austenite TMCP conditions in a Gleeble apparatus. Atom probe tomography (APT), scanning transmission electron microscopy in a focused ion beam equipped scanning electron microscope (STEM-on-FIB) and electrical resistivity measurements provide complementary information on the precipitation status and are correlated with each other. It will be demonstrated that accurate electrical resistivity measurements can monitor the general consumption of solute microalloys (Nb) during hot working which was complemented by APT measurements of the steel matrix. On the other hand, STEM revealed that a large part of Nb-containing particles during hot working are co-precipitated with titanium during cooling from the austenitizing temperature. Precipitates that form during cooling or isothermal holding can be distinguished from strain-induced precipitates by corroborating STEM measurements with APT results. APT specifically allows obtaining detailed information about the chemical composition of precipitates as well as the distribution of elements inside the particle. Electrical resistivity measurement, on the contrary, provides macroscopic information on the progress of precipitation and can be calibrated by APT. The current paper highlights the complementarity of these methods and shows first results within the framework of a larger study on strain-induced precipitation.

In this research we are reporting gas sensing properties of TiO_2-x/TiO₂-based hetero-structure, which was ‘self-heated’ by current that at constant potential passed through the structure. Amperometric measurements were applied for the evaluation of sensor response towards ethanol, methanol, n-propanol and acetone gases/vapors. The sensitivity towards these gases was based on electrical resistance changes, which were determined by amperometric measurements of current at fixed voltage applied between Pt-based contacts/electrodes deposited on TiO_2-x/TiO₂-based layer. XRD analysis revealed the formation of TiO_2-x/TiO₂-based hetero-structure, which is mainly based on Ti₃O₅/TiO₂ formed during hydro-thermal oxidation based sensing layer preparation process. Additionally, photoluminescence and time-resolved photoluminescence decay kinetics based signals of this sensing structure revealed the presence of TiO₂ mainly in the anatase phase in the TiO_2-x/TiO₂-based hetero-structure, which was formed at 400°C annealing temperature. The evaluation of TiO_2-x/TiO₂-based gas sensing layer was performed at several different temperatures (25°C, 72°C, 150°C, 180°C) and at these temperatures different sensitivity to aforementioned gaseous materials was determined.

Titanium dioxide (TiO2) and aluminum oxide (Al2O3) coatings have been investigated in a wide range of bio-applications due to their biodegradation and biocompatibility properties, that are key parameters for their use in the food packaging and biomedical devices fields. The present study evaluates and compares the electrochemical behavior of the non-coated, commercial resin-coated, TiO2-coated and Al2O3-coated aluminum in commercial beer electrolyte. For this, TiO2 and Al2O3 thin films were deposited on aluminum (Al) substrates using atomic layer deposition (ALD). The evaluation of the corrosion barrier layer properties was performed by linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). In addition, profilometry, grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) analyses were performed to investigate the physical and chemical properties of the pristine and / or corroded samples. TiO2 and Al2O3 films presented an amorphous structure, a morphology that follows Al substrate surface, and a thickness of around 100 nm. Analysis of LSV data showed that ALD coatings promoted a considerable increase in corrosion barrier efficiency being 86.3% for TiO2-coated Al and 80% for Al2O3-coated Al in comparison with 7.1% of commercial resin-coated Al. This is mainly due to the lower electrochemical porosity, 11.4% for TiO2-coated Al and 20.4% for Al2O3-coated Al in comparison with 96% of the resin-coated Al, i.e. an increase of up to twofold in the protection of Al when coated with TiO2 compared to Al2O3 coated. The EIS results allow us to complement the discussions about the reduced corrosion barrier efficiency of the Al2O3 film for beer electrolyte once SEM and FT-IR analyzes did not show drastic changes in both investigated ALD films after the corrosion assays. The above results indicate that ALD TiO2 and Al2O3 films may be a viable alternative to replace the synthetic resin coatings frequently used in aluminum cans of use in the food industry.

Spherical microparticles of TiO₂ were synthesized by the ionic liquid-assisted solvothermal method at different reaction time (3, 6, 12 and 24h). The properties of the prepared photocatalysts were investigated by means of UV-vis diffuse-reflectance spectroscopy (DRS), BET surface area measurements, scanning electron microscopy (SEM), X-ray diffraction analysis (XRD), and X-ray photoelectron spectroscopy (XPS). The results indicated that the efficiency of phenol degradation was related with a time of the solvothermal synthesis as determined for TiO₂_EAN(1:1)_24h sample. Microparticles of TiO₂_EAN(1:1)_3h formed during the only 3h of synthesis time revealed really high photoactivity under visible irradiation – 75%. This value increased to 80% and 82% after 12h and 24h, respectively. The photoactivity increase was accompanied by the increase of the specific surface area thus pores size, as well as ability to absorb UV-vis irradiation. The high efficiency of phenol degradation of IL-TiO₂ photocatalysts was ascribed to the interaction between the surface of TiO₂ and ionic liquid components (carbon and nitrogen).

In this work, nanocomposite photoelectrodes of the TiO2/ Au composition were manufactured, in which the size of plasmonic Au nanoparticles was varied, and the morphology of the TiO2 layer, depending on the thickness, changed from an island to a continuous layer. The influence of the morphology of plasmonic Au nanoparticles and the TiO2 layer on the optical and photoelectrochemical characteristics of hybrid photoelectrodes was studied. It has been shown that continuous coating of Au nanoparticles with a TiO2 layer (layer thickness 10 and 15 nm) leads to a decrease in the photoelectric response, and the decrease in photocurrent density and photoconversion efficiency decreases in proportion to the thickness of the TiO2 layer. The indicated drop in characteristics when plasmonic particles are located under the TiO2 layer is presumably associated with the scattering and recombination of charge carriers in the semiconductor layer. The best performance was shown by a system in which large Au nanoparticles (10 nm) are coated with a 5 nm thick layer of titanium dioxide; in this geometry, Au nanoparticles are decorated with TiO2 nanoparticles, as a result of which the photoelectrode-electrolyte interface has a more complex structure.

Bioactive surface coatings have retained the attention of researchers and physicians due to their versatility and range of applications in orthopedics, particularly in infection prevention. Antibacterial metal nanoparticles (mNPs) are a promising therapeutic, with vast application opportunities on orthopedic implants. The current research aimed to construct a polyelectrolyte multilayer on a highly porous titanium implant using alternating thin film coatings of chitosan and alginate via the layer-by-layer (LbL) self-assembly technique, along with the incorporation of silver nanoparticles (AgNPs) or titanium dioxide nanoparticles (TiO2NPs), for antibacterial and osteoconductive activity. These mNPs were characterized for their physicochemical properties using quartz crystal microgravimetry with dissipation system, nanoparticle tracking analysis, scanning electron microscopy, and atomic force microscopy. Their cytotoxicity and osteogenic differentiation capabilities were assessed by AlamarBlue and alkaline phosphatase (ALP) activity assays, respectively. The antibiofilm efficacy of the mNPs tested against Staphylococcus aureus. The LbL polyelectrolyte coating was successfully applied to the porous titanium substrate. A dose-dependent relationship between nanoparticle concentration and ALP as well as antibacterial effects was observed. TiO2NP samples were also less cytotoxic than AgNP counterparts, although similarly antimicrobial. Together, these data serve as a proof-of-concept for a novel coating approach for orthopedic implants with antimicrobial and osteoconductive properties.

We overview recent findings achieved in the field of model-driven development of additively manufactured porous materials for development of a new generation of bioactive implants for orthopedic applications. Porous structures produced of biocompatible titanium alloys by selective laser melting can present a promising material to design scaffolds with regulated mechanical properties and with capacity to be loaded with pharmaceutical products. Adjusting pore geometry, one could control elastic modulus and strength/fatigue properties of the engineered structures to be compatible with bone tissues, thus preventing the stress shield effect when replacing a diseased bone fragment. Adsorption of medicals by internal spaces would make it possible to emit the antibiotic and anti-tumor agents into surrounding tissues. We critically analyze the recent advances in the field featuring model design approaches, virtual testing of the designed structures, capabilities of additive printing of porous structures, biomedical issues of the engineered scaffolds and so on. A special attention is paid to highlight the current troubles in the field and the ways of their solutions.

Four leather substrates from different animals were treated by dispersions containing hydrophilic composite silica-hyperbranched poly(ethylene imine) xerogels. Antimicrobial activity was introduced by incorporating silver nanoparticles and /or benzalkonium chloride. The gel precursor solutions were also infused before gelation to titanium oxide powders typically employed for induction of self-cleaning properties. The dispersions from these biomimetically premade xerogels integrate environmentally friendly materials with short coating times. Scanning electron microscopy (SEM) provided information on the powder distribution onto the leathers. Substrate and coating composition were estimated by infrared spectroscopy (IR) and ener-gy-dispersive X-ray spectroscopy (EDS). Surface hydrophilicity and water permeability were assessed by water-contact angle experiments. The diffusion of the leather's initial components and xerogel additives into the water were measured by Ultraviolet-Visible (UV-Vis) spectroscopy. Protection against GRAM- bacteria was tested for Escherichia coli, Pseudomonas aeruginosa, and Klebsiella Pneumoniae against GRAM+ bacteria for Staphylococcus aureus, and Enterococcus faecalis and against fungi for Candida albicans. Antibiofilm capacity experiments were performed against Staphylococcus aureus, Klebsiella Pneumoniae, Enterococcus faecalis, and Candida albicans. The application of xerogel dispersions proved an adequate and economically feasible alternative to the direct gel formation into the substrate’s pores for the preparation of leathers intended for medical uses

Titanium dioxide (TiO₂) micro and nano architectures have been intensively studied in the past years because of many varied applications in environmental, energy conversion, and storage fields, such as heterogeneous catalysis, dye-sensitized solar cells, lithium/sodium ion batteries, lithium-sulfur (Li-S) batteries, and bio-nanotechnology, etc. Especially the surface and interface structures in the TiO₂ structures play important roles in those applications. This mini review article focuses on TiO₂ micro and nano architectures with the prevalent crystal structures (anatase, rutile, brookite, and TiO₂(B)), and summarizes major advances in the surface and interface engineering and applications in environmental and electrochemical applications. We present the principles and growth mechanisms of TiO₂ nanostructures via different strategies, with an emphasis on rational control of the surface and interface structures. We further discuss the applications of TiO₂ micro and nano architectures in photocatalysis, lithium/sodium ion batteries, and Li-S batteries. Throughout the discussion, the relationship between the device performance and the surface structures of TiO₂ micro/nano structures will be highlighted. Then we discuss the phase transitions of TiO₂ nanostructures and possible strategies of improving the phase stability. The review concludes with a perspective on the current challenges and future research directions.

A variety of techniques have been utilized in metal additive manufacturing (AM) for melt pool size management, including modeling and feed-forward approaches. In a few cases, closed-loop control has been demonstrated. In this research, closed-loop melt pool size control for large-scale, laser-wire based Directed Energy Deposition is demonstrated with a novel modification: site-specific changes to the controller set-point were commanded at trigger points, the locations of which were generated by the projection of a secondary geometry onto the primary 3D-printed component geometry. The present work shows that, through this technique, it is possible to print a specific geometry that occurs beyond the actual toolpath of the print head. This is denoted as an extra-toolpath geometry and is fundamentally different from other methods of generating component features in metal AM. A proof-of-principle experiment is presented in which a complex oak leaf geometry was embossed on an otherwise ordinary double-bead wall made from Ti-6Al-4V. The process is introduced and characterized primarily from a controls perspective with reports on the performance of the control system, the melt pool size response, and the resulting geometry. The implications of this capability, which extend beyond localized control of bead geometry to the potential mitigations of defects and functional grading of component properties, are discussed.

Lithium titanates are used in various applications, such as anode materials for lithium intercalation (Li4Ti5O12) or breeding materials in fusion reactors (Li2TiO3). Here, we report the formation of nano-crystalline lithium titanates by a mechanochemical approach and present a deeper insight into their structural characteristics by PXRD and solid-state NMR spectroscopy. The compounds were synthesized in a high energy planetary ball mill with varying milling parameters and different grinding tools. NaCl type Li2TiO3 (α-Li2TiO3) was formed by dry milling of lithium hydroxide with titania (rutile or anatase) and by a milling induced structure transformation of monoclinic β Li2TiO3 or spinel type Li4Ti5O12. Heating of mechanochemical prepared α Li2TiO3 induces a phase transformation to the monoclinic phase similar to hydrothermal reaction products, but a higher thermal stability was observed for the mechanochemical formed product. Microstructure and crystallographic structure were characterized by PXRD via Rietveld analysis. Detailed phase analysis shows the formation of the cubic phase from the various educts. A set of two lattice parameters for α Li2TiO3 was refined, depending on the presence of OH- during the milling process. An average crystallite size of less than 15 nm was observed for the mechanochemical generated products. The local Li environment detected by 6Li SPE MAS NMR revealed Li defects in the form of tetrahedral instead of octahedral site occupation. Subsequent adjustment of the structural model for Rietveld refinement leads to better fits, supporting this interpretation.

Accumulation of proteins in filter membranes limits the efficiently of filtering technologies for cleaning wastewater. Efforts are ongoing to coat commercial filters with different materials (such as titanium-dioxide, TiO2) in order to reduce the fouling of the membrane. Beyond monitoring the desired effect of retention of biomolecules, it is demanding to understand what are the biophysical changes in water-soluble proteins caused by interacting with the new coated filter membranes, an aspect that has received little attention so far. Using spin label electron paramagnetic resonance (EPR), aided with native fluorescent spectroscopy and dynamic light scattering (DLS), here we report the changes in the structure and dynamics of bovine serum albumin (BSA) exposed to TiO2 (P25) nanoparticles or passing through commercial polyvinylidene fluoride (PVDF) membranes coated with the same nanoparticles. We have found that the filtering process and prolongued exposure to TiO2 nanoparticles had significant effects on different regions of BSA, and denaturation of the protein was not observed, neither with TiO2 nanoparticles nor by pressing through TiO2-coated filter membranes.

Diamond-like carbon (DLC) layers are known for their high corrosion and wear resistance, low friction, and high biocompatibility. However, it is often necessary to dope DLC layers with additional chemical elements to strengthen their adhesion to the substrate. Ti-DLC layers (doped with 0.4, 2.1, 3.7, 6.6, 12.8 at.% of Ti) were prepared by dual pulsed laser deposition, and pure DLC, glass, and polystyrene (PS) were used as controls. In vitro cell-material interactions were investigated with an emphasis on cell adhesion, proliferation, and osteogenic differentiation. We observed slightly increasing roughness and contact angle and decreasing surface free energy on Ti-DLC layers with increasing Ti content. Three-week biological experiments were performed using adipose tissue-derived stem cells (ADSCs) and bone marrow mesenchymal stem cells (bmM-SCs) in vitro. The cell proliferation activity was similar or slightly higher on the Ti-doped materials than on glass and PS. Osteogenic cell differentiation on all materials was proved by collagen and osteocalcin production, ALP activity, and Ca deposition. The bmMSCs exhibited greater initial proliferation potential and an earlier onset of osteogenic differentiation than the ADSCs. The ADSCs showed a slightly higher formation of focal adhesions, higher metabolic activity, and Ca deposition with increasing Ti content.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

A diffusion welding of coarse-grained and ultrafine-grained (UFG) specimens of titanium near-α alloy Ti-5Al-2V used in nuclear power engineering was made by Spark Plasma Sintering. The failure of the welded specimens in the conditions of hot salt corrosion and of electrochemical corrosion were shown to have preferentially intercrystalline character. In the case of presence of macrodefects, crevice corrosion of the welded joints was observed. The resistance of the alloys against the intercrystalline corrosion was found to be determined by the concentration of vanadium at the titanium grain boundaries, by the size and volume fraction of the β-phase particles and by the presence of micro- and macropores in the welded joints. The specimens of the welded joints of the UFG alloy have higher hardness, hot salt corrosion resistance and the electrochemical corrosion.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

Addressing global environmental problem, water splitting to produce hydrogen fuel by solar energy is getting so much attention. In the water splitting, the essential problem to solve is the development of efficient　catalysts for oxygen production. In this paper, having the prospect for a practical application of photocatalysts to artificial photosynthesis, molecular mechanisms in the current literature are briefly reviewed. At first, recent progress in the function of Mn cluster at the natural photosystem II is briefly described. The kinds of devices in which oxygen evolution reaction (OER) catalysts are used were designated; water electrolyzers, photoelectrodes, and photocatalysts. Some methods for analyzing molecular mechanism in OER catalysis, emphasized by FTIR method, are shown briefly. After describing common OER mechanisms, the molecular mechanisms are discussed for TiO2 and BiVO4 photoelectrodes with our novel data, followed by presenting of co-catalysts IrO2, RuO2, NiO2, and other metal oxides for OER catalysts. Recent reports describing OER catalysts of perovskites, layered double hydroxides (LDH), metal-organic frameworks (MOF), single atom catalysts, as well as metal complexes are reviewed. Finally, by comparing with natural photosystem, the requiring factors to improve the activity of the catalysts for artificial photosynthesis will be discussed.

Many stable water dispersions of various chemical compositions containing bioactive chemical compounds: copper silicate, titanium dioxide and zinc oxide (and other auxiliary substances) were developed and fabricated - they were used for preparation of thin hybrid coatings having very good antimicrobial properties against gram negative bacteria (Escherichia coli), gram positive bacteria (Staphylococcus aureus) and yeast fungus (Candida albicans). Polyester (PES) nonwovens were modified by dip-coating, and PES and cotton fabrics - by dip-coating and coating methods.