Battery-powered electric vehicles (EVs) have emerged as an environmentally friendly and efficient alternative to traditional internal combustion engine vehicles, while their single-charge driving distances under cold conditions are significantly limited due to the high energy consumption of heating systems. Heat pumps can provide an effective heating solution for EVs, but their coefficient of performance (COP) is hampered by heat transfer deterioration due to frost accumulation. This study proposes a solution to this issue by introducing a microchannel heat exchanger (MHE) with superhydrophobic surface treatment (SHST) as a heat pump evaporator. A computational-fluid-dynamics MHE model and a dynamic heat pump model are developed and rigorously validated to examine the detrimental impact of frost accumulation on heat transfer, airflow resistance, and heat pump performance. When the frost layer thickness is 0.8 mm at a given air-side velocity of 1.0 m/s, the air-side heat transfer coefficient can be reduced by about 75%, and the air-side pressure drop sharply increases by 28.4 times. As frost thickness increases from 0 to 0.8 mm, the heating effect drops from 3.97 to 1.82 kW, and the system COP declines from 3.17 to 2.30. Experimental results show that the frost thickness of the MHE with SHST reaches approximately 0.4 mm after 30 minutes, compared to that of 0.8 mm of the MHE without SHST, illustrating the defrosting capability of the superhydrophobic coating. The study concludes by comparing the performance of various heating methods in EVs to highlight the advantages of SHST technology. As compared to traditional heat pumps, the power consumption of the proposed system is reduced by 48.7% due to the defrosting capability of the SHST. Moreover, the single-charge driving distance is extended to 327.27 km, an improvement of 8.99% over the heat pump without SHST.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

Tomatoes, one of the most appreciated vegetables consumed, are crops well adapted for cultivation in arid and semi-arid conditions, the success of large yields is guaranteed by covering water consumption through irrigation. Solar Pumps - SP are driven by Photovoltaic Panels - PV (SPAPV), eliminating the dependence on electricity or diesel; they are environmentally friendly because they generate carbon-free electricity and the cost of operation and maintenance is lower. In order to preserve the water administered by drip to the tomato crop grown in solariums, mulching is used. In Husasău de Tinca, in the Crișurilor Plain, cultivation of tomato varieties without mulching (WM) and with mulching with black foil (MBF) were studied. To answer the question "How effective are water conservation measures in terms of energy independence?", two variants of SPAPVs, direct pumping (ADP) and storage tank (AST) were simulated. Considering the conditions in the solariums, tomato crops do not benefit from the contribution of precipitation, therefore it is proposed to determine the water consumption of tomatoes (ETRo), using the temperatures inside the solarium. In 2016, the average temperatures during the vegetation period were observed with an insurance of over 20 %, the irrigation norms were 6945.7 m3 ha-1, for the WM variant and 6594.0 m3 ha-1 for the MBF variant, respectively. Specific Investment (SI) is 214,795 Euro ha-1 in case of ADP and respectively 202,990 Euro ha-1 in case of ATS. The payback period (IPT) is between 2.68 years and 2.53 years for the ADP variant and between 1.63 years and 1.54 years for the ATS variant, respectively. The indications for water use and irrigation water use show that in the MBF variant the water administered by localized irrigation is better utilized than in the WM variant. In the conditions of Crișurilor Plain, the best solution for the distribution of water in solariums, with the help of SPAPVs is the mulching system of tomatoes grown in solariums (MBF) and the arrangement of the drip irrigation system with a water storage tank (ATS).

Low pressure fluid transport (1) applications often require low and precise volumetric flow rates (2) including low leakage to reduce additional costly and complex sensors. A peristaltic pump de-sign (3) was realized, with the fluid’s flexible transport channel formed by a solid cavity and the wobbling plate comprising a rigid and a soft layer (4). In operation, the wobbling plate is driven externally by an electric motor, hence, the soft layer is contracted and unloaded (5) during pump-cycles transporting fluid from low to high pressure sides. A thorough characterization of the pump system is required to design and dimension the components of the peristaltic pump. To capture all these parameters and their dependencies on various operation-states, often complex and long-lasting dynamic 3D FE-simulations are required. We present, here, a holistic design methodology (6) including analytical as well as numerical calculations, and experimental valida-tions for a peristaltic pump with certain specifications of flow-rate range, maximum pressures, and temperatures. An experimental material selection process is established and material data of candidate materials (7) (liquid silicone rubber, acrylonitrile rubber, thermoplastic-elastomer) are directly applied to predict the required drive torque. For the prediction, a semi-physical, analyti-cal model was derived and validated by characterizing the pump prototype.

Almost fifty years after the first installations, I identify the main lessons learned from fighting drought and poverty in Africa with direct solar-powered pumps thanks to Father Bernard Verspieren and Mali Aqua Viva. Six main findings and three main recommendations emerge from the present analysis. They are of direct relevance to all Africa’s countries whose population has gone from 438 million in 1977 to 1,308 million in 2019, with about 600 million still having no access to electricity. In place of “awareness campaigns” and extraordinary courses held by international organizations, I recommend to establish national solar energy institutes whose task will include the education of solar energy professionals giving practice-oriented workshops on solar-powered drip irrigation and rainwater harvesting throughout each Africa’s country. Said education will critically include the economic and social aspects of distributed “generation” of energy and water from sunlight and rainfall.

Aero-fuel centrifugal pumps are important power plants in aero-engines. Unlike most of the existing centrifugal pumps, a combination impeller is integrated with the pump to improve its performance. First, the critical geometrical parameters of combination impeller and volute are given. Then, the effects of combination impeller on flow characteristics inside the impeller and volute are clarified by comparing simulation results with that of the conventional impeller, where the effectiveness of selected numerical method is validated by an acceptable agreement between simulation and experiment. Finally, the experiment is performed to test the external performance of studied pump. A significant feature of this study is that the flow characteristics are significantly ameliorated by reducing the flow losses emerged in impeller inlet, impeller outlet and volute tongue. Correspondingly, the head and efficiency of combination impeller are higher with comparison to conventional impeller. Consequently, it is a promising approach in ameliorating flow field and improving external performance by applying a combination impeller to an aero-fuel centrifugal pump.

Antibiotic resistance represents a significant threat to the modern healthcare provision. The ESKAPEE pathogens, in particular, have proven to be especially challenging to treat, due to their intrinsic and acquired ability to rapidly develop resistance mechanisms in response to environmental threats. The development of biofilm has been characterised as an essential contributing factor towards antimicrobial-resistance and tolerance. Several studies have implicated the involvement of efflux pumps in antibiotic resistance, both directly, via drug extrusion and indirectly, through the formation of biofilm. As a result, the underlying mechanism of these pumps has attracted considerable interest due to the potential of targeting these protein structures and developing novel adjunct therapies. Subsequent investigations have revealed the ability of efflux pump-inhibitors (EPIs) to block drug-extrusion and disrupt biofilm formation, thereby, potentiating antibiotics and reversing resistance of pathogen towards them. This review will discuss the potential of EPIs as a possible solution to antimicrobial resistance, examining different challenges to the design of these compounds, with an emphasis on Gram-negative ESKAPEE pathogens.

Bacterial antibiotic resistance has become a major global health concern. One of the main reasons for the development of multi-drug resistance properties in bacteria is due to the bacterial efflux pump systems. They are important transport proteins, mainly involved in the removal of toxic substrates like antibiotics from inner cell environment. These pumps are responsible for the intrinsic ability of bacteria to get resistant to the antibiotic. Various types of efflux pumps are present in the Gram-positive and Gram-negative bacteria. Plant-derived products like Capsaicin, Olympicin A, and Indirubicin were found to be inhibitors of an efflux pump in Staphylococcus aureus similarly Ursolic acid derivatives; Daidzein and Lanatoside C were plant-derived inhibitors of an efflux pump in Escherichia coli. In this review detail information have been provided about efflux pump inhibitors that have been found to be effective in the Gram-positive bacteria and Gram-negative bacteria. The aim of this review is to focus on the role of plant-derived compounds as effective efflux pumps inhibitors with reference to mainly Staphylococcus aureus and Escherichia coli.

Developing high performance HVAC system using natural refrigerants including carbon dioxide (CO₂) has been important in respect of environmental preservation and associated technologies. Thus studies to optimize the HVAC (heating ventilation air conditioner) system using natural refrigerants through clarifying the cycle performance characteristics are necessary. The CO₂ heat pump system using air and water sources was consisted to examine its performance characteristics, and by varying conditions of several factors that affect or characterize the system performance like the amount of refrigerant charge, EEV (electronic expansion valve) opening, and internal heat exchanger under cooling mode. The performance characteristics of CO₂ heat pump system were tested by using an air enthalpy calorimeter. In the case of the CO₂ heat pump system without internal heat exchanger, the opening of #3 EEV and #4 EEV was 60% and refrigerant charge amount was 5,600g. However, in the case of that with internal heat exchanger, the best performance was obtained when the opening of #2 EEV is 20%. From the present studies, it was observed that the performance variation and operational characteristics of the CO₂ heat pump system were affected by design factors like refrigerant charge amount, EEV opening, and internal heat exchanger and thereby, the configuration on an optimal operation conditions of the system was enabled.

The electrification of process industries is one of the main challenges when building a low-carbon society since they consume huge amounts of fossil fuel generating different emissions. Heat pumps are one of the instruments to perform industrial sector of carbon-neutral market players. This paper proposes an approach to improve the economic feasibility of heat pumps within the process plants. Initial energy targeting with Grand Composite Curves was used and supplemented with the detailed design of the evaporator and compressor for different condensation and evaporation pressures. The trade-off between the capital cost of the heat pump and the electricity cost was investigated and optimal configurations were selected. The case study investigates the gas fractioning unit of a polymer plant where three heat pumps were integrated into distillation columns. The results demonstrated that the heat recovery is 174 MW and requires an additional 37.9 MW of electricity to reduce hot utility by 212 MW. The selection of evaporation and condensation pressure of heat pumps allows saving of 21.5 M€/y for 7 years of plant operation.

Fluorescent bioprobes are invaluable tools for visualizing live cells and deciphering complex biological processes by targeting intracellular biomarkers without disrupting cellular functions. In addition to protein-binding concepts, fluorescent probes utilize various mechanisms, including membrane, metabolism, and gating-oriented strategies. This study introduces a novel fluorescent mechanism distinct from existing ways. Here, we developed a B-cell selective probe, CDrB, with unique transport mechanisms. Through SLC-CRISPRa screening, we identified two transporters, SLCO1B3 and SLC25A41, by sorting out populations exhibiting higher and lower fluorescence intensities, respectively, demonstrating contrasting activities. We confirmed that SLCO1B3, with comparable expression levels in T and B cells, facilitates the transport of CDrB into cells, while SLC25A41, overexpressed in T lymphocytes, actively exports CDrB. The observation suggests that SLC25A41 plays a crucial role in discriminating between T and B lymphocytes. Furthermore, it reveals the potential for reversible localization of SLC25A41 to demonstrate its distinct activity. This study is the first report to unveil a novel strategy of SLC by exporting the probe. We anticipate that this research will open up new avenues for developing fluorescent probes.

A fluorescent probe, N'-((3-methyl-5-oxo-1-phenyl-4, 5-dihydro-1H-pyrazol-4-yl) methylene)-2-oxo-2H-chromene-3-carbohydrazide (MPMC), was synthesized and characterized. Characterizations of the synthetic MPMC were conducted by proton nuclear magnetic resonance (1HNMR) spectroscopy and carbon-13 nuclear magnetic resonance spectroscopy (13C NMR). The fluorescence emission behaviors of probe MPMC towards diverse metal ions were detected and the probe exhibited high sensitivity and selectivity towards Cu2+ over other metal ions via quenching of its fluorescence. Furthermore, the existence of other metal actions made no difference on the fluorescence intensity of the MPMC-Cu2+ system apparently, that is, MPMC displayed a good anti-interference ability. Job’s plot of MPMC and copper ions indicated the detection limit was 15.16 nM (R2=0.9612) for the assayed actions, with a stoichiometric ratio of 1:1 for MPMC and Cu2+. Additionally, the color of MPMC probe solution changed from nearly colorless to yellow in the presence of Cu2+ in visible light, which the color change could be observed by the naked eye. Similarly, the color resolved bright yellow into blue in ultraviolet light. Also reusability studies indicated that MPMC probe was reusable. The pH effect of probe MPMC to Cu2+ had a broad range of pH detection 4.0 to 11.0. The response time of MPMC probe for determining Cu2+ was within 1 min. The recognition of Cu2+ by MPMC performed on pre-treated paper under sunlight and UV light both had a distinct colour change. Thus, the solid-state method for detecting Cu2+ with the naked-eye, was both economical and convenient.

Hemoconcentration membranes used in cardiopulmonary bypass require a pore structure design with high pure water permeability, and which does not allow protein adsorption and useful protein loss. However, studies on hemoconcentration membranes have not been conducted yet. The purpose of this study was to analyze three-dimensional pore structures and protein fouling before and after blood contact with capillary membranes using the tortuous pore diffusion model and a scanning probe microscope system. We examined two commercially available capillary membranes of similar polymer composition that are successfully used in hemoconcentration clinically. Assuming the conditions of actual use in cardiopulmonary bypass, we perfused these membranes with bovine blood. Pure water permeability before and after bovine blood perfusion was measured using the dead-end filtration. The scanning probe microscopy system was used for analysis. High-resolution three-dimensional pore structures on the inner surface of the membranes were observed before blood contact. On the other hand, pore structures after blood contact could not be observed due to protein fouling. The pore diameters calculated by the tortuous pore diffusion model and scanning probe microscopy were mostly similar and could be validated reciprocally. Achievable pure water permeabilities showed no difference despite protein fouling, leading to low values of albumin SC. This is due to the mechanism that protein fouling occurs on the membrane surface, while there is little internal pore blocking. Therefore, controlling the fouling is essential for membranes in medical use. These characteristics of the hemoconcentration membranes examined in this study are suitable for clinical use.

: Electric air conditioning and heating systems capacity is growing rapidly. So does the nameplate capacity of PV power plants. While demand in cooling has a positive correlation with solar irradiationirradiance, the demand in heating has an opposite relation. In this study, different approaches of to design (aggregation; energy storagethermal, battery and implicit systems storage) and control (frequency conversion; variable and adaptive load) and their effects on the efficiency of an off-grid active thermal stabilisation system based on a solar-powered heat pump are analysed. The case considered is permafrost thermal stabilisation system in Norway. It is shown that proper layout and control of the system with an adaptive load can reduce the capital expenses expenditures and the total cost of ownership by 30-40%. Increase in the efficiency capacity factor and cooling stability of the systems with the aggregated and threshold power consumervariable load due to the principle of aggregation is studied. The downside of that is the increase in compressors operation time by 50% with variable load and by 25% per unit with aggregation which means more frequent replacement in terms of motor-hours. But The the feasibility of this approaches considered are applicable for a wide range of solar-powered facilities, but the results are is quite case sensitive and depends on the prices for low-power heat pumps. The prospects of using the excess refrigerant and soil for thermal energy storage instead of traditional electrochemical batteries are considered.

A revised reversed Carnot cycle without external heat source and temperature gap is proposed to challenge the classic reversed Carnot cycle, heat pumps based on the proposed cycle with super energy efficiency works just like electric heater fitted for any climate including extreme cold weather, the application of these new heat pumps is discussed with conclusion that little real obstacles exist for scale application to address the heating related climate change, also a demonstration case shows a remarkable results to encourage the applications of these new heat pumps.

Finnish government's carbon neutrality goal by 2035 requires integration of renewable energy sources into the power grid. Considering the stochasticity of these resources, additional sources of flexibility are necessary to balance supply and demand in the power grid. District heating network (DHN) operators in Finland plan to shut down fossil-fuel-based combined heat and power plants and electrify heating systems by deploying heat pumps (HPs) and electric boilers. Techno-economic analysis and optimal operation of DHN-connected HPs and electric boilers in providing ancillary balancing services considering the 15-minute granularity in the balancing markets in Finland were investigated. The objective was to maximize the potential revenue for DHN operators gained from the day-ahead electricity market and frequency containment reserve (FCR) balancing markets. Three inter-connected DHNs in the Helsinki metropolitan area were optimized considering the reference year 2019 and each operator's decarbonization strategies for 2025. HPs could gain the highest profit from FCR-D up-regulation market, while the electric boiler may gain considerable profits from FCR-D down-regulation market. Compared to other balancing markets studied, the FCR-N market had a limited profit margin. Sensitivity analysis indicated that spot electricity prices and CO2 emission allowance prices have a significant impact on the profit from balancing markets.

The number of XLPE cables being used near or beyond their designed lifespan is increasing. The importance of timely cable replacement is increasing. Therefore, research is actively being conducted using VLF Tan δ diagnostic technology to assess the insulation condition of cables. There is a lack of studies measuring and analyzing VLF Tan δ of service aged XLPE cables. Additionally, there is a lack of research considering the operating environment. Therefore, research is needed to diagnose and analyze the insulation condition of the same serviced aged cable when it is operated in a different environment. This paper evaluates and analyzes the insulation condition of cables installed in the BFP, cooling tower, and deaerator booster pump of a combined heat and power plant. Each cable was analyzed by measuring VLF Tan δ, dielectric breakdown test of the cable, and tensile strength, elongation at break, crystallinity, and dielectric strength of XLPE specimens. Additionally, the correlation between VLF Tan δ and other characteristics was also analyzed. It was found that degradation progressed in the order of BFP, cooling tower, and deaerator booster pump. Therefore, it was confirmed that even for the same cable, deterioration varies depending on the installation location.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

As the core components of water jet propulsion system, water jet pump, directly affect the ship's propulsion performance. 3D reverse design method can effectively suppress the impeller secondary flow to get better performing hydraulic models. Aiming at fast and efficient optimization of the impellers, we parameterize the impellers and runner, and coupled with optimization algorithms and numerical calculations. It is an efficient and feasible way to coupling optimization based on multi-parameter, multi-objective and optimization algorithms, and parameterizing the impellers and guide vane geometry based on the 3D model designed by 3D reverse design method. In this paper, the waterjet propulsion pump is taken as the research object. According to the design method of the waterjet propulsion pump hydraulic model, the traditional axial flow blade design method, the modern ternary design theory of the blades, and the parametric three-dimensional reverse design method are selected to constructing an optimal design optimization strategy for the impeller of water-jet propulsion pump based on multi-parameter and multi-object genetic algorithm. Under the design conditions, the optimized pump efficiency reaches 89.28%, which is 1.24% higher than the original hydraulic model. The optimized pump head is 13.51 m, which is 0.39m more than the original hydraulic model. Under the design condition, the test measured head is 13.26m, the numerical calculation result is 1.88% higher than the test result, the test measured efficiency is 87.1%, the numerical calculation result is 2.5% higher than the test result. From the test results, the optimized impeller has higher hydraulic performance. Experiments have shown that it is feasible to optimize the design strategy.

Vacuum pump wear is the most prevalent failure mode of the IBA Synthera® automated radiochemistry system. Rebuilding or replacing the pump causes equipment downtime and increases the radiation exposure of the service personnel. We built a dedicated test device to assess new or rebuilt pumps prior to installation, thus reducing downtime and radiation exposure during repairs. The Testbed incorporates a microprocessor that actuates the pump, valves, pressure sensor, and communicates with the user through lights, buttons, and an alphanumeric screen. The Testbed increases productivity and safety in the radiochemistry laboratory.

We report a preliminary exploration on the low-pressure Ar-O2 plasma generated by low-frequency alternating current (AC) power supply in the low-temperature Plasma Experimental Power Supply (CTP-2000S) for the first time. The electron density 〖(n〗_e), the electron temperature 〖(T〗_e) and the electron energy distribution function (EEDF) are measured by the single Langmuir probe in this experiment. Experimental results show that the ne increases with gas pressure rising, while the ne decreases with the oxygen concentrations rising. And, a plasma density peak is also observed with the AC power supply increase. A comparison between this work and the previous results by RF source suggests that the low-frequency AC power supply may be very fruitful exploration to generate the low-pressure plasma.

A novel hybrid CSP-PV power plant is presented. Instead of the integration used in current hybrid power plants, where part of the PV production is charged into the thermal energy storage system through electrical resistors, the proposed system integrates both PV and thermal solar fields using a high-temperature heat pump. Both the heat pump and the heat engine are based on Brayton supercritical CO2 thermodynamic cycles. Such integration allows for charging the molten salts storage as if a central tower receiver field supplied the thermal energy, whereas parabolic trough collectors are employed. Unlike conventional hybrid plants, where the storage of PV production leads to a decrease in power injected into the grid throughout the day, the power injected by the proposed system remains constant. The heat engine efficiency is 44.4%, and the COP is 2.32. The LCOE for a 50 MWe plant with up to 12 hours of storage capacity is 171 $/MWh, which is lower than that of existing CSP power plants with comparable performance. Although the cost is higher compared to a PV plant with batteries, this hybrid system offers two significant advantages: it eliminates the consumption of critical raw materials in batteries, and all the electricity produced comes from a synchronous machine.

At present more than 9 million people die of cancer every year. Simple and broad-spectrum drugs are still an urgent need for cancer patients. Recently, we proposed a new hypothesis that intracellular osmotic pressure (IOP) is the driving force of cell division, and abnormal tumor proliferation is the result of uncontrolled IOP in cells. On the one hand, aneuploidy and abnormal function of Na⁺/K⁺ pump lead to a faster rise of IOP in tumor cell than normal cells, on the other hand, abnormality of cytoskeleton assembly leads to the decrease of tolerance limit of cell membrane (TLCM) of tumor cells for resisting IOP. This hypothesis predicts: 1)Tumor cells were more intolerant to hypotonic stress than normal cells. 2) Maligancies may be sellectively killed by a suddenn increase of IOP and combined with decrease of the TLCM of tumors. Na⁺/K⁺ pump inhibitors can promotely increase the IOP of tumor cells and cytoskeleton inhibitors can dramatically lower the TLCM of tumor cells. Therefore, Na⁺/K⁺ pump and cytoskeleton inhibitors may have a synergetic effect to kill tumor cells. 3) Molecules regulating cell osmolality may be new targets for cancer treatment.

The impact of snow darkening by deposition of light absorbing aerosols (LAAs) on snow cover over the Himalaya-Tibetan-Plateau (HTP) and influence on the Asian monsoon are investigated using the NASA Goddard Earth Observing System Model Version 5 (GEOS-5). We find that during April-May-June, deposition of LAAs on snow leads to a reduction in surface albedo, initiating a sequence of feedback processes, starting with increased surface solar radiation, rapid snowmelt in HTP and warming of the surface and upper troposphere, followed by enhanced low-level southwesterlies and increased dust loading over the Himalayas-Indo-Gangetic Plain. The warming is amplified by increased dust aerosol heating, and subsequently amplified by latent heating from enhanced precipitation over the Himalaya foothills and northern India, via the Elevated Heat Pump (EHP) effect during June-July-August. The reduced snow cover in the HTP anchors the enhanced heating over the Tibetan Plateau and its southern slopes, in conjunction with an enhancement of the Tibetan Anticyclone, and the development of an anomalous Rossby wavetrain over East Asia, leading to weakening of the subtropical westerly jet, and northward displacement and intensification of the Mei-Yu rainbelt. Our results suggest that atmosphere-land heating by LAAs, particularly desert dust play a fundamental role in physical processes underpinning the snow-monsoon relationship proposed by Blandford more than a century ago.

Background. Gene rearrangements affecting KMT2A are frequent in acute myeloid leukemia (AML) and are often associated with a poor prognosis. KMT2A gene fusions are often detected by chromosome banding analysis and confirmed by fluorescence in-situ hybridization. However, small intragenic insertions, termed KMT2A partial tandem duplication (PTD), are particularly challenging to detect using standard molecular and cytogenetic approaches. Methods. We have validated the use of a custom hybrid capture based next-generation sequencing (NGS) panel for comprehensive profiling of AML patients seen at our institution. This NGS panel targets the entire consensus coding DNA sequence of KMT2A; to deduce the presence of a PTD we used the relative ratio of KMT2A exons coverage. We sought to corroborate the KMT2A-PTD NGS results using (1) multiplex-ligation probe amplification (MLPA) and (2) optical genome mapping (OGM). Results. We analyzed 932 AML cases and identified 41 individuals harboring a KMT2A-PTD. MLPA, NGS and OGM confirmed the presence of a KMT2A-PTD in 22 of the cases analyzed where orthogonal testing was possible. Two false positive PTD calls by NGS could be explained by the presence of cryptic structural variants impacting KMT2A and interfering with PTD analysis. OGM revealed the nature of these previously undetected gene rearrangements in KMT2A, while MLPA yielded in-conclusive results. MLPA analysis for KMT2A-PTD is limited to exon 4, whereas NGS and OGM resolved KMT2A-PTD sizes and copy number levels. Conclusion. KMT2A-PTDs are complex gene rearrangements that cannot be fully ascertained using a single genomic platform. MLPA, NGS panels and OGM are complementary technologies applied in standard of care testing for AML patients. MLPA and NGS panels are designed for targeted copy number analysis; however, our results show that integration of concurrent genomic alterations is needed for accurate KMT2A-PTD identification. Unbalanced chromosomal rearrangements overlapping with KMT2A can interfere with the diagnostic sensitivity and specificity of copy number based KMT2A-PTD detection methodologies.

This study examines the optimization of ground source heat pump (GSHP) systems and energy piles for sustainable urban development, with a focus on Southeast Asia. GSHPs, which utilize geothermal energy for indoor HVAC needs, offer a sustainable alternative to traditional systems by utilizing consistent subsurface temperatures for heating and cooling. The study highlights the importance of understanding thermal movement within the soil, especially in soft marine clays prevalent in Southeast Asia, to improve GSHP system efficiency. Using a one-dimensional finite-difference model, the study examines the effects of soil thermal conductivity and density on system performance. The results show that GSHP systems, especially when integrated with energy piles, significantly reduce electricity consumption and greenhouse gas emissions, underscoring their potential to mitigate the urban heat island effect in densely populated areas. Despite challenges posed by the region's hot and humid climate, which could affect long-term effectiveness, the study highlights the need for further study, including field experiments and advanced modeling techniques, to optimize GSHP configurations and fully exploit geothermal energy in urban environments. The study's insights into soil thermal dynamics and system design optimization contribute to the advancement of sustainable urban infrastructure development.

Pseudomonas aeruginosa is an opportunistic pathogen that poses a significant threat to individuals with chronic respiratory ailments, such as cystic fibrosis (CF). The pathogen is highly prevalent in CF individuals and is responsible for chronic infection, resulting in severe tissue damage and poor patient outcome. However, early detection and immediate treatment are critical to prevent bacterial persistence and establishment of chronic infection. Presently, antibiotics including aminoglycosides, beta-lactams, polymyxins, and fluoroquinolones along with anti-inflammatory medications are being used to treat P. aeruginosa infections in CF patients. However, prolonged antibiotic administration has led to the emergence of widespread multidrug resistance in P. aeruginosa (CF isolates), contributing to antimicrobial resistance (AMR) and failure of antimicrobial therapies. Thus, exploring viable alternatives such as antivirulence therapeutics can be vital towards managing pseudomonal infections in CF patients and mitigating the risk of AMR. In this direction, antivirulence strategies achieving targeted inhibition of bacterial virulence pathways/factors, including quorum sensing, efflux pumps, lectins, and iron chelators, have been widely explored against CF isolates of P. aeruginosa. Simultaneously, there have been discussions about the sufficiency of in vitro findings and their successful translation in pulmonary infection models (in vivo) for the clinical implementation of antivirulence therapies hence, this review article presents a bird’s eye view on the pulmonary infections involving P. aeruginosa in CF patients by laying emphasis on factors contributing to bacterial colonization, persistence, and disease progression along with the current line of therapeutics against P. aeruginosa in CF while underscoring the limitation of antimicrobial approaches. We further collate scientific literature and comprehensively discuss the various antivirulence strategies that have been successfully tested against P. aeruginosa isolates from CF patients. This could pave the way towards a paradigm shift towards clinical therapy of pseudomonal infections in CF and can potentially override conventional antimicrobial treatments.

A developed six-port reflectometry (SPR) system was integrated to measure the relative permittivity of tumor and normal breast tissue for medical diagnostic purpose. In order to obtain an accurate and precise measurement, the calibration process was done to the SPR using the well-known three-standard technique. Next, the studied dielectric probe was connected to the calibrated measurement-port of the SPR. The open end of the probe aperture was dibbed into the normal and tumor synthetic breast tissue samples to measure the synthetic breast tissues dielectric constant, ɛrʹ, and loss factor, ɛrʺ in the frequency range of 1.5 GHz to 3.3 GHz. Finally, the comparative studies were conducted between commercial VNA with Keysight 85070E dielectric probe and the studied SPR-probe system based on the measured magnitude of the reflection coefficient, phase shift, dielectric constant, and loss factor of the synthetic breast samples. The maximum absolute errors of the measured reflection coefficient magnitude, phase shift, dielectric constant, and loss factor were found to be 0.01, 1.07°, 1.12, and 0.75, respectively. It was ascertained that the predicted dielectric constant, ɛrʹ, is able to differentiate between normal, (ɛrʹ < 50) and tumor, (ɛrʹ > 50) breast tissues.

Mexico shows a high birth prevalence of congenital hypothyroidism (CH) due to thyroid dysgenesis (TD). PAX8 defects underlie only 1% of these cases and NKX2-1 does not seem to be involved. Here, we analyzed other TD-related genes in 128 non-related Mexican patients (females 77.3%; 6 months to 16.6 years) with non-syndromic CH-TD diagnosis established by clinical evaluation, thyroid hormone serum profiling, and scintigraphy (74%) or ultrasonography (26%). We performed Sanger sequencing of FOXE1, NKX2-5, and TSHR and evaluated copy number variations (CNVs) in TSHR, FOXE1, PAX8, and NKX2-1 by multiplex ligation-dependent probe amplification. Odds ratios for TD risk were explored for FOXE1 polyalanine stretches [polyAla-rs71369530] in cases and controls (N=116). Five rare missense changes cataloged as benign (NKX2-5:p.(Ala119Ser)-rs137852684), of unknown significance (FOXE1:p.(Ala335Gly)-rs543372757; TSHR:p.(Asp118Asn)-rs1414102266), and likely pathogenic (FOXE1:p.(Gly124Arg)-rs774035532; TSHR:p.(Trp422Arg)-rs746029360) accounted for 1.5% (N=2/128) of clinically relevant genotypes (supported in part by protein modeling) in CH-TD. No CNVs were identified, nor did polyAla >14 alanines in FOXE1 significantly protect against TD. The present and previously published data collectively show that small clinically relevant germline variants in PAX8, FOXE1, and TSHR are found in only a very small proportion (2.5%) of isolated CH-TD Mexican patients.

Temperature differences between the atmosphere and river water allow rivers to be used as a hydrothermal energy source. The river-water heat pump system is a relatively non-invasive renewable energy source; however, effluent discharged from the heat pump can cause downstream temperature changes which may impact sensitive fluvial ecosystems. In this study, the water temperature recovery distance of the effluent was estimated for a river section in the Han River Basin, Korea, using the heat transfer equation and the Environmental Fluid Dynamic Code (EFDC) model. Results showed that, compared to the EFDC model, the heat transfer equation tended to overestimate the water temperature recovery distance due to its simplified assumptions. The water temperature recovery distance could also be used as an objective indicator to decide the reuse of downstream river water. Furthermore, as the river system was found to support an endangered fish species that is sensitive to water environment changes, care should be taken to exclude the habitats of protected species affected by water temperatures within water temperature recovery distance.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

COVID-19 and long COVID-19 vulnerabilities may be caused indirectly by albumin binding deficiency (ABD) which can be corrected by the correct administration of human serum albumin (HSA). The liver is the primary site of nutrient regulation and fluid volume maintenance, control of both is by changes to albumin concentration. In healthy subjects the HSA lymphatic nutrient pump (HSALNP) ensures continual pumping of nutrients from the liver are appropriately distributed to organs. Nutrients are delivered to cells according to the availability of binding to HSA. The HSALNP therefore maintains the correct nutrients and colloidal pressure balance in all tissues independently. In unhealthy tissues, following COVID-19 infection, the passage of HSA/nutrients through the interstitial spaces and lymph will be impeded. Fluid therapy into the periphery leads to dilution of essential nutrients attached to the protein-carriers such as albumin. The levels of albumin being charged by the liver with nutrients is critical in maintaining immune stability by maintaining nutrient support and colloidal pressure of cellular structures. The site of HSA binding by the liver is of great importance and direct infusion of albumin into the Hepatic Portal Vein is the most appropriate method of maintaining colloid pressure and cellular nutrient levels.

The object of this work is to determine the correlation on the Nusselt number on the individual rows of a four-row tubular finned heat exchanger with continuous fins with a staggered tube arrangement using CFD modelling. Correlations for calculating Darcy-Weisbach friction factors on individual tube rows were also determined. Relationships for the Nusselt number and friction factor derived for the entire exchanger based on CFD modelling were compared with those available in the literature determined using experimental data. The maximum relative differences between the Nusselt number for a four-row exchanger determined experimentally and by CFD modelling are in the range from 22% for a Reynolds number based on a tube's outside diameter of 1,000 to 30% for a Reynolds number of 13,000. The maximum relative differences between the friction factor for a four-row exchanger determined experimentally and by CFD modelling are in the range of 50% for a Reynolds number based on a tube outer diameter of 1,000 to 10% for a Reynolds number of 13,000. The CFD modeling performed shows that in the range of Reynolds numbers based on hydraulic diameters from 150 to 1,400, the Nusselt number for the first row in a four-row finned heat exchanger is about 22% to 15% higher than the average Nusselt number for the entire exchanger. In the range of Reynolds number changes based on hydraulic diameter from 2,800 to 6,000, the Nusselt numbers on the first and second rows of tubes are close to each other. Correlations on Nusselt numbers and friction factors derived for individual tube rows can be used in the design of plate-fin and tube heat exchangers used in equipment such as air-source heat pumps, automotive radiators, air-conditioning systems and in air hot-liquid coolers. In particular, the correlations can be used to select the optimum number of tube rows in the exchanger.

This paper proposes and demonstrates, in full scale, a novel type of energy geostructure (“the Climate Road”) that combines a ground source heat pump (GSHP) with a sustainable urban drainage system (SUDS) by utilizing the gravel roadbed simultaneously as energy source and rainwater retarding basin. The Climate Road measures 50m x 8m x 1m (length, width, depth) and has 800 m of geothermal piping embedded in the roadbed, serving as the heat collector for a GSHP that supplies a nearby kindergarten with domestic hot water and space heating. Model analysis of operational data from 2018-2021 indicates sustainable annual heat production levels around 0.6 MWh per meter road, with a COP of 2.9-3.1. The continued infiltration of rainwater to the roadbed increases the amount of extractable heat by an estimated 17% compared to the case of zero infiltration. Using the developed model for scenario analysis we find that draining rainwater from three single family houses and storing 30% of the annual heating consumption in the roadbed, increases the predicted extractable energy by 56% compared to zero infiltration with no seasonal energy storage. The Climate Road is capable of supplying three single family houses with heating, cooling and rainwater management year-round.

This paper explores the Wilsonian renormalization group of probe-D-branes, focusing on the Dirac-Born-Infeld (DBI) action. The analysis involves deriving the constant of motion and formulating the Wilsonian renormalization group equation. The study extends to the infrared regime, considering both zero and non-zero temperatures. Additionally, thermodynamic aspects related to the functional form of the grand potential are discussed. The investigation provides insights into the renormalization of probe-D-branes and their thermodynamic properties.

Objectives: We aimed to clarify the endoscopic and clinicopathological features of raspberry-shaped gastric lesions (RSGLs) and to establish an endoscopic diagnostic algorithm for RSGLs. Methods: We collected RSGLs from an endoscopic database at our hospital between May 2009 and August 2021. All RSGLs were histopathologically classified and compared based on their endoscopic and clinicopathological characteristics. Results: Sixty-five RSGLs in 54 patients were classified into five histopathological types: gastric adenocarcinoma of foveolar type (GA-FV, n = 43), gastric adenocarcinoma of fundic-gland type (GA-FG, n = 2), gastric adenocarcinoma of fundic-gland mucosa type (GA-FGM, n = 4), hyperplastic polyp (HP, n = 12), and proton pump inhibitor-related lesion (PPI-L, n = 4). All RSGLs exhibited polygonal or curved marginal crypt epithelium (MCE). GA-FV lesions had homogenously reddish (95%) and irregular microvascular (MV) pattern (91%). GA-FG lesions were heterogeneously reddish with a submucosal tumor shape (100%) and had a regular MV pattern (50%). GA-FGM lesions were homogenously reddish (75%) and occasionally had a submucosal tumor shape (50%) with an irregular MV pattern (75%). HP and PPI-L were homogeneously reddish (93%), with linear or dotted MCE (81%) and a regular MV pattern (100%). Conclusion: Our diagnostic algorithm for RSGLs constructed using endoscopic features might be useful for the endoscopic differential diagnosis of RSGLs.

Recent technological advancements in produced water for the oil and gas industry have a long history that spreads over centuries and has roots with many mathematicians, physicists, engineers, and inventors. Working to understand the many ideas and questions has helped to bring the produced water technologies to where we are today. Fluid mechanics is an essential factor in the world of engineering because it comes with significant benefits when designing the necessary equipment to overcome the challenging endeavors of daily operations. Many of us believe certain ideas or products were developed within a specific year not fully understanding the idea or concept might be hundreds of years old. For example, when we think of fluid mechanics, we do not think of Archimedes' immersing King Hiero II crown in water. Archimedes did this to determine the displacement of the water as he knew gold was denser than silver. Archimedes was one of the pioneers who was part of the beginning of fluid mechanics. Another interesting fact is the first valve invented was in 1 AD by Heron of Alexandria. This valve can be described as the very first hydraulic valve. The evolution of technology over hundreds of years has made considerable innovations benefiting engineers all over the world. These innovations come in the form of PLCs, RTUs, PIDs, mathematical formulas, processing methods, and SCADA systems.