Experimental measurement of porous polypropylene (PP) using the DTC-25 TA laboratory equipment and hot box test has been compared. The thermal conductivity of materials indicates the insulation capability of building materials. Excellent building materials will have a lower thermal conductivities value as well as other building insulator performance metrics. While results show that increasing the volume fraction of fluid in the porous PP has an inverse association with the thermal conductivity of the material as predicted by porous media theories, there is a marked difference in the measured values of the thermal conductivity using the two methods. The thermal conductivity values of porous from DTC-25 and hot box test were 0.21 and 0.0033 W/mK, respectively. The difference in the thermal conductivity values was due to the misapplication of the Fourier’s guarded heat flow model in the DTC-25 device to a convective fluid porous medium material.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

Forestry workers play a crucial role in implementing forest management programs, but their outdoor work exposes them to rising temperatures caused by global climate change, which poses potential health risks related to heat. This study focuses on Indonesian forestry workers and examines the relationship between their knowledge of heat-related issues, risk perception, and precautionary behavior in dealing with increasing workplace heat exposure. Developing effective precautionary behavior is essential for preventing heat-related health disorders and promoting health protection programs. To facilitate a comprehensive comparison of the three variables, interviews were conducted with two groups of outdoor workers, comprising 210 forestry workers and 215 paddy farmers. The findings indicate that increasing knowledge about heat-related issues promotes precautionary behavior, and risk perception acts as a mediator between knowledge and behavior. Additionally, the study highlights that the emotion of "dread" intensifies perceived risk and predicts positive behavior change. To enhance heat-related knowledge, exploring the potential use of a "fear" tone is important. In conclusion, comprehensive strategies need to be implemented to promote precautionary behavior among vulnerable forestry workers, particularly manual laborers.

This work exclusively focuses on the assessment of the thermal performance of a multifunctional facade panel incorporating PCM in foam layers, recurring to a hot box heat flux meter method to determine the thermal transmittance (U-value). The experimental setup is based on the steady-state approach using climatic chambers, assuring a stable thermal environment. Even small fractions of PCM achieved a small reduction in thermal amplitude. Numerical simulations using Ansys Fluent were developed to evaluate the performance of PCM use over a wide range of temperature boundary conditions and operating modes. These numerical models were calibrated and validated using the results of experimental tests, achieving a correlation factor of 0.9674, thus accurately representing a real-world scenario. The decrement factor (f) was used to analyse the data. It was identified that the efficiency of the panel and size of the optimum region increased with the PCM fraction growth. The simulated behaviour was optimum when the input mean temperature is of 20 °C for a room temperature of between 18-20 °C. The results show the significant potential of the multi-layered panel and the thermal regulator effect of the PCM incorporated on indoor space temperature to reach good thermal comfort levels.

Background: The new media provides a convenient digital platform to access, use and exchange health information. As a special group of health care, maternal is still of international concern due to their high mortality rate. Improving maternal health as a Millennium Development Goal of the United Nations is an important quest for the health care system. Scientific research provides advice on how to improve maternal health through stringent reasoning and accurate data. However, the dramatic increase of publications, the diversity of themes, and the dispersion of researchers may reduce efficiency. Objective: This study aims to analyze the research progress on maternal health under the global new media environment, exploring the current research hotspots and research frontiers. Methods: A scientometric analysis was carried out by CiteSpace5.7.R1, searching in the core database of Web of Science for articles published in English from 1998 to 2021, and combined topic words such as new media, maternal, and health. In total, 3312 articles have been retrieved, of which 2270 studies have been included for further analysis. Top countries and institutions, potentially high-impact literature, research frontiers, and hotspots were analyzed in this study. Results: The number of publications grew rapidly after 2008, from 29 publications sharply increasing to 472 publications by 2020. Research centers concentrated in Latin America, such as the University of Toronto, the University of California. The work of Larsson M, Lagan BM, Tiedje L, and Helle C had a high potential impact. Most of the research subjects were maternal and newborn babies, and the research frontiers focused on health education and maternal psychological problems. Maternal mental health, maternal and infant nutrition, weight, production technology, and equipment were hotspots. Conclusion: The development of new media has brought a new era for maternal health, characterized by psychological qualities, healthy and reasonable physical conditions, and advanced technology.

In this study, the effect of hot stamping forming process on the properties change of compound layer in Al–Si coated high-strength steel sheet with different thickness was investigated. The coating layer in hot stamped high-strength steel sheet was composed of a diffusion layer and a compound layer. As the hot stamping temperature and holding time for forming increased, the thickness of the compound layer in the Al–Si coated high-strength steel sheet increased. The thickness of coating layer with the hot stamping for 500 sec at 890, 910 and 950 °C was obtained 8.9, 11.8, and 20.6 micrometer, respectively. The thickness of coating layer with hot stamping for 180, 500 and 550 sec at 910 ^oC was obtained 5.7, 11.8, and 17.8 micrometer, respectively. The compound layer in hot stamped high-strength steel sheet with Al–Si coating layer consists of Al_5.4Fe₂ and Fe₂Si phases. In the compound layer, Al and Si were irregularly distributed.

The influence of the Fe2O3 addition amount on the dephosphorization of hot metal at 1623 K with the slag of the low basicity (CaO/SiO2) of about 1.5 was investigated by using high-temperature laboratorial experiments. With increasing the Fe2O3 addition amount, the contents of [C], [Si], [Mn] and [P] in hot metal at the end of dephosphorization decrease, and the corresponding removal ratios increase. The P2O5 content in slag increases, and the CaO and SiO2 contents in slag decrease. The phosphorus mainly exists in the form of the nCa2SiO4-Ca3(PO4)2 solid solution in the phosphorus-rich phase and the value of coefficient n decreases from 20 to 1 with increasing the Fe2O3 addition amount from 5 g to 30 g. With increasing the Fe2O3 addition amount, the oxygen potential and activity at the interface between the slag and hot metal increase. When the oxygen potential and the oxygen activity at the interface are greater than 0.72×10-12 and 7.1×10-3, respectively, the dephosphorization ratio begins to increase rapidly. With increasing the Fe2O3 addition amount to 30 g, the ratio of the Fe2O3 addition amount to theoretical calculation consumption is around 175%, and the dephosphorization ratio reaches the highest value of 83.3%.

Cyber security plays an important role to protect our computer, network, program and data from unauthorized access. Intrusion detection system (IDS) and intrusion prevention system (IPS) are two main categories of cyber security, designed to identify any suspicious activities present in inbound and outbound network packets and restrict the suspicious incident. Deep neural network plays a significant role in the construction of IDS and IPS. This paper highlights a novel IDS using optimized convolution neural network (CNN-IDS). An optimized CNNIDS model is an improvement over CNN which selects the best weighted model by considering the loss in every epoch. All the experiments have been conducted on the well known NSL-KDD dataset. Information gain has been used for dimensionality reduction. The accuracy of the proposed model is evaluated through optimized CNN for both binary and multiclass categories. Finally, a critical comparison has been performed with other general classifiers like J48, Naive Bayes, NB tree, Random forest, Multilayer Perceptron (MLP), Support Vector Machine (SVM), Recurrent Neural Network (RNN) and Convolution Neural Network(CNN). All the experimental results demonstrate that the optimized CNN-IDS model records the best recognition rate with minimum model construction time.

The spike protein of SARS coronavirus (SARS-CoV) attaches the virus to its cellular receptor, angiotensin-converting enzyme 2 (ACE2), which is mediated by the receptor binding domain (RBD) of the spike protein. Recently, an analysis based on decade-long structural studies of SARS was reported to illustrate with atomic-level details receptor recognition by the novel coronavirus from Wuhan, i.e., 2019-nCoV. Here, this article reports a comprehensive set of structural electrostatic analysis of all SARS-CoV spike protein RBD-related structures as of February 13, 2020, aiming at identifying the electrostatic hot spots for SARS-CoV spike protein to be complexed with ACE2 and its neutralizing antibodies. First, this article identified a structural action mechanism of the F26G19 antibody (of SARS-CoV spike protein), where its Asp56 residue binds to the Arg426 of the SARS-CoV spike protein RBD against the formation of the interfacial Arg426-Glu329 salt bridges between ACE2 and the SARS-CoV spike protein RBD. Second, a hypothesis is reported that a pair of electrostatic clips exist at the interface between ACE2 and the SARS-CoV spike protein RBD, including both Arg426-Glu329 and His445-Glu23-Lys447 salt bridges. Last, this article reports a structurally identified interfacial Glu35-Arg479 salt bridge which helps stabilize the complex structure of ACE2 and the SARS-CoV spike protein RBD. Overall, the structurally identified electrostatic hot spots reported here may be useful for the design of SARS-CoV-neutralizing antibodies in future.

This paper presents the microstructural and mechanical properties of low and medium carbon advanced high-strength forging steels developed based on the third generation advanced high-strength sheet steels, in conjunction with those of conventional high-strength forging steels. Hot-forging followed by an isothermal transformation process considerably improved the mechanical properties of the forging steels. The improvement mechanisms of the mechanical properties were summarized by relating to the matrix structure, the strain-induced transformation of metastable retained austenite and/or a mixture of martensite and austenite.

The effect of filling velocity on positive macrosegregations in large size steel ingots was studied. Macrosegregation and macro-/micro-structure were characterized on the hot-tops and a portion of the upper section of two ingots. The measurements revealed that segregation features in the two ingots varied as a function of the alloying elements, and that the severity of positive macrosegregation in the casting body was reduced when the filling rate was increased. It was also found that at the higher filling rate, grain morphologies in the first solidified zones of the ingot changed from columnar to equiaxe, and secondary dendrite arm spacing (SDAS) became slightly smaller in the intermediate and final solidified zones. The experimental findings were analyzed in the framework of diffusion and convection controlled solidification, as well as liquid metal flow theories. The solute dependence of segregation features was related to the difference in solid-liquid partition coefficient and diffusion capability of each element in the liquid iron. Calculation of Reynolds numbers (Re) during the filling process, for both ingots, showed that higher filling velocity caused more instable movement of the liquid metal in the initial solidification stage, resulting in the modification of grain morphology, as well as accelerated solidification rate.

Hot stamping dies include cooling channels to treat the formed sheet. The optimum cooling channels of dies & molds should adapt to the shape and surface of the dies, so that a homogeneous temperature distribution and cooling are guaranteed. Nevertheless, cooling ducts are conventionally manufactured by deep drilling, attaining straight channels unable to follow the geometry of the tool. Laser Metal Deposition (LMD) is an additive manufacturing technique capable to fabricate nearly free-form integrated cooling channels and therefore shape the so-called conformal cooling. The present work investigates the design and manufacturing of conformal cooling ducts, which are additively built up on hot work steel and then milled in order to attain the final part. Their mechanical performance and heat transfer capability has been evaluated, both experimentally and by means of thermal simulation. Finally, conformal cooling conduits are evaluated and compared to traditional straight channels. The results show that LMD is a proper technology for the generation of cooling ducts, opening the possibility to produce new geometries on dies & molds and, therefore, new products.

It is well known that that there is an intrinsic link between the financial and energy sectors, which can be analyzed through their spillover effects, which are measures of how the shocks to returns in different assets affect each other’s subsequent volatility in both spot and futures markets. Financial derivatives, which are not only highly representative of the underlying indices, but can also be traded on both the spot and futures markets, include Exchange Traded Funds (ETFs), a tradable spot index whose aim is to replicate the return of an underlying benchmark index. When ETF futures are not available to examine spillover effects, “generated regressors” are useful for constructing both Financial ETF futures and Energy ETF futures. The purpose of the paper is to investigate the co-volatility spillovers within and across the US energy and financial sectors in both spot and futures markets, by using “generated regressors” and a multivariate conditional volatility model, namely Diagonal BEKK. The daily data used are from 1998/12/23 to 2016/4/22. The data set is analyzed in its entirety, and are also subdivided into three distinct subsets. The empirical results show there is a significant relationship between the Financial ETF and Energy ETF in the spot and futures markets. Therefore, financial and energy ETFs are suitable for constructing a financial portfolio from an optimal risk management perspective, and also for dynamic hedging purposes.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

To weaken the harm of Al-Si coating and increase the strength of welded joint, variable thickness of Ni foil (Ni, an austenitic formation element) was added into the lap laser welding Al-Si coated 22MnB5 hot stamping steel/galvanized steel joints. The joints' weld appearance, microstructure, and mechanical properties were explored. The weld altered from X-shape to Y-shape with the increased thickness of Ni foil. During welding, Al-Si coating was melted and diluted into the welding pool, forming δ-ferrite (a rich-Al phase with low toughness and strength) in FZ and FB. This phase deteriorated the strength of the joints. After adding Ni, the amount and size of the δ-ferrite phase decreased. With a significant thickness of Ni foil, δ-ferrite would disappear. However, a new phase (FM, rich-Ni phase) probably formed except PM(a no or negligible Ni phase). The heat-affected zone (HAZ) on the side of 22MnB5 comprised a coarse martensite zone, refined martensite zone, martensite+ferrite zone, and tempered martensite zone from the FZ to the basic material. HAZ on the side of galvanized steel mainly contained ferrite and pearlite. After adding Ni foil, the strength of the joint was more than that without Ni. The maximum strength of the joint can be up to 679MPa because of the disappearance of δ-ferrite. Meanwhile, the toughness of the joint increased. The fracture mode was from three mixed fractures(cleavage, quasi-cleavage, and dimple) to one fracture(dimple).

For a wide industrial application of magnesium alloys, a method for imparting high damping properties while maintaining mechanical properties is required. Controlling the crystallographic texture seems to be useful, because dislocations are known to have a significant influence on the damping characteristics of magnesium alloys. Therefore, the effect of twinning and annealing, which can affect to the recrystallization were investigated in this study. An AZ31 alloy was hot rolled at 673K with a reduction ratio of 10 % and 50 %, and then annealed at 673K and 723K for 0.5, 1, 2, and 3H respectively. SEM-EBSD was used to examine the microstructure and texture. In addition, each specimen’s hardness and internal friction were contemporarily measured. As a result, hot rolling produced tensile twins and their fraction increased with internal friction when the reduction ratio increased. Due to annealing, a discontinuous type of static recrystallization occurred within the twinning grains, and was highly activated along with the increasing annealing temperature and the fraction of twinning. In the samples annealed at 723K, the internal friction continuously increased over the annealing time, whereas in the samples annealed at 673K, the decrease in dislocation density was delayed while, the internal friction showed a relatively low value.

This work aims to investigate systematically the influence of process temperature, bio-mass-to-water ratio, and production scales (laboratory and pilot) on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale, as well as at 200, 225, and 250 °C, 2 °C/min, bio-mass-to-water ratio of 1:10, in laboratory scale. The elemental composition (C, H, N, S) of solid phase determined to compute the HHV. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas an-alyzer. For the experiments in pilot scale with constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential de-cay with temperature, while that of liquid and gaseous phases a smooth growth. By varying the biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied be-tween 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with increasing temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total car-boxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentra-tions of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfu-ral, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio. For the experiments in laboratory scale with constant biomass-to-water ratio of 1:10, the yields of solid ranged between 55.9 and 51.1% (wt.), showing not only a linear decay with tem-perature, but also a lower degradation grade. The chemical composition of main organic compounds (furfu-ral, HMF, phenols, cathecol, and acetic acid) dissolved in the aqueous phase in laboratory scale shows the same behavior of those in obtained in pilot scale.

This work aims to investigate systematically the influence of process temperature and biomass-to-water ration on the chemical composition of aqueous and gaseous phases and mass production of chemical by hydrothermal processing of Açaí (Euterpe Oleraceae, Mart.) seeds. The hydrothermal carbonization carried out at 175, 200, 225, and 250 °C, 2 °C/min, biomass-to-water ratio of 1:10, and at 250 °C, 2 °C/min, and biomass-to-water ratios of 1:10, 1:15, and 1:20, in technical scale. The chemical composition of aqueous phase determined by GC and HPLC and the volumetric composition of gaseous phase by using an infrared gas analyzer. For constant biomass-to-water ratio of 1:10, the yields of solid, liquid, and gaseous phases varied between 53.39 and 37.01% (wt.), 46.61 and 59.19% (wt.), and 0.00 and 3.80% (wt.), respectively. The yield of solids shows a smooth exponential decay with temperature, while that of liquid and gaseous phases a smooth growth. By variation of biomass-to-water ratios, the yields of solid, liquid, and gaseous reaction products varied between 53.39 and 32.09% (wt.), 46.61 and 67.28% (wt.), and 0.00 and 0.634% (wt.), respectively. The yield of solids decreases exponentially with increasing water-to-biomass ratio and that of liquid phase increases in a sigmoid fashion. For constant biomass-to-water ratio, the concentrations of Furfural and HMF decrease drastically with temperature, reaching a minimum at 250 °C, while that of phenols increases. In addition, the concentrations of CH3COOH and total carboxylic acids increase, reaching a maximum at 250 °C. For constant process temperature, the concentrations of aromatics vary smoothly with the temperature. The concentrations of furfural, HMF, and cathecol decrease with temperature, while that of phenols increases. The concentrations of CH3COOH and total carboxylic acids decrease exponentially with temperature. Finally, for the experiments with varying water-to-biomass ratios, the productions of chemicals (furfural, HMF, phenols, cathecol, and acetic acid) in the aqueous phase is highly dependent on the biomass-to-water ratio.

This cross-sectional study evaluated the validity of three alternative methods compared to the gold standard 24-h urine collection for estimating dietary sodium intake, a modifiable risk factor for hypertension, among middle-aged and older adults with elevated blood pressure. These included spot urine collection (using Kawasaki, Tanaka, and INTERSALT equations), 24-h dietary recall, and food frequency questionnaire responses, compared against 24-h urine collection in a subset of 65 participants (aged 50–75 years, 58.5 % women, 61.6 % hypertensive) from the DePEC-Nutrition trial. The validity of the methods was assessed using bias, Spearman correlation coefficient (SCC), intraclass correlation coefficient (ICC), and Bland-Altman analysis. Among the alternative methods, spot urine collection using the Kawasaki equation showed the strongest correlation (SCC 0.238; ICC 0.119, 95 % CI -0.079 to 0.323) but it exhibited a significant bias (1414 mg/day, p-value < 0.001) relative to 24-h urine collection. Conversely, dietary surveys had a smaller bias but wider limits of agreement. These findings underscore the complexities of accurately estimating dietary sodium intake using spot urine collection or dietary surveys in this specific population, suggesting that a combination or refinement of existing methodologies might improve accuracy. Further research with larger samples is necessary to develop more reliable methods for assessing sodium intake in this high-risk group.

Anthracnose (ANT) and angular leaf spot (ALS) are significant diseases in common bean, leading to considerable yield losses under specific environmental conditions. The California Dark Red Kidney (CDRK) bean cultivar is known for its resistance to multiple races of both pathogens. Previous studies have identified the CoPv01CDRK/PhgPv01CDRK resistance loci on chromosome Pv01. Here, we evaluated the expression levels of ten candidate genes near the CoPv01CDRK/PhgPv01CDRK loci and plant defense genes using quantitative real-time PCR in CDRK cultivar inoculated with races 73 of Colletotrichum lindemuthianum and 63-39 of Pseudocercospora griseola. Gene expression analysis revealed that the Phvul.001G246300 gene exhibited the most elevated levels, showing remarkable 7.8-fold and 8.5-fold increases for ANT and ALS, respectively. The Phvul.001G246300 gene encodes an abscisic acid (ABA) receptor pyrabactin resistance - PYR1-like (PYL) protein, which plays a central role in crosstalk between ABA and jasmonic acid responses. Interestingly, our results also showed that the other defense genes were initially activated. These findings provide critical insights into the molecular mechanisms underlying plant defense against these diseases and could contribute to the development of more effective disease management strategies in the future.

Forest degradation is known to be widespread in the tropics, but is currently very poorly mapped, in part because there is little quantitative data on which satellite sensor characteristics and analysis methods are best at detecting it. To improve this, we used data from the Tropical Forest Degradation Experiment (FODEX) plots in the southern Peruvian Amazon, where different numbers of trees had been removed from four 1 ha forest plots, carefully inventoried by hand and Terrestrial Laser Scanning before and after the logging to give a range of biomass change (ΔAGB) values. We conducted a comparative study of six multispectral optical satellite sensors (WorldView-3, SkySat, SPOT-7, PlanetScope, Sentinel-2 and Landsat 8) at 0.3 – 30 m spatial resolution, to find the best combination of sensor and remote sensing indicator for change detection. Spectral reflectance, the Normalized Difference Vegetation Index (NDVI) and texture parameters were extracted after radiometric calibration and image preprocessing. The strength of the relationships between the change in these values and field-measured ΔAGB (computed in % ha−1) was analysed. The results demonstrate that: (a) texture measures correlates more with ΔAGB than simple spectral parameters; (b) the strongest correlations are achieved for those sensors with spatial resolutions in the intermediate range (1.5 - 10 m), with finer or coarser resolutions producing worse results, and (c) when texture is computed using a moving square window ranging between 9 - 14 m in length. Maps predicting ΔAGB showed very promising results using a NIR-derived texture parameter for 3 m resolution PlanetScope (R2 = 0.97 and RMSE = 1.80 % ha−1), followed by 1.5 m SPOT-7 (R2 = 0.74 and RMSE = 5.25 % ha−1) and 10 m Sentinel-2 (R2 = 0.71 and RMSE = 5.55 % ha−1). Texture models derived from 0.3 m WorldView-3 improved with increasing window size, with highest R2 of 0.62 and RMSE = 6.35 % ha−1 for a window of 14 m in length. The degradation in our field plots is invisible to the 30 m resolution Landsat data. Our findings imply that, at least for lowland Peru, low-medium intensity disturbance can be detected best in optical wavelengths using a texture measure derived from 3 m PlanetScope data. That such data are being collected daily, and currently released free as monthly mosaics over tropical forests as part of the Norway’s International Climate and Forest Initiative (NICFI), is excellent news for monitoring such degradation.

Risk of cardiovascular disease (CVD), common in childhood cancer survivors (CCSs), may be affected by diet. We assessed sodium (Na) and potassium (K) intake, estimated from food frequency questionnaires (FFQs) and morning urine spots, and its associations with cardiovascular risk in CCSs. We stratified CCS into three risk profiles based on A) personal history (CVD, CVD risk factors, or CVD risk free), B) body mass index (obese, overweight, or normal/underweight), and C) cardiotoxic treatment (anthracyclines and/or chest irradiation, or neither). We obtained a FFQ from 802, and sent a spot urine sample collection kit to 212, of which 111 (52%) returned. We estimated Na intake 2.9 g/day based on spot urine and 2.8 g/day based on FFQ; estimated K intake was 1.6 g/day (spot urine) and 2.7 g/day (FFQ). CCSs with CVD risk factors had a slightly higher Na intake (3.3 g/day), than CCSs risk free (2.9 g/day) or with CVD (2.7 g/day, p = 0.017), and obese participants had higher Na intake (4.2 g/day) than normal/underweight CCSs (2.7 g/day, p<0.001). Daily Na intake was above, and daily K intake below national recommended levels. Adult survivors of childhood cancer need dietary assistance to reduce Na and increase K intake.

Plant leaf diseases can affect the plants’ leaves to an extent that the plants can collapse and die completely. These diseases may drastically drop the supply of vegetables and fruits to the market, and result in a low agricultural economy. In the literature, different laboratory methods of plant leaf disease detection have been used. These methods were time consuming and could not cover large areas for the detection of leaf diseases. This study infiltrates through the facilitated principles of the Convolutional Neural Networks (CNN) in order to model a network for image recognition and classification of these diseases. Neuroph was used to perform the training of a CNN network that recognized and classified images of the maize leaf diseases that were collected by use of a smart phone camera. A novel way of training and the methodology used, expedite a quick and easy implementation of the system in practice. The developed model was able to recognize 3 different types of maize leaf diseases out of healthy leaves. The Northern Corn Leaf Blight (Exserohilum), Common Rust (Puccinia sorghi) and Gray Leaf Spot (Cerospora) diseases were chosen for this study as they affect most parts of Southern Africa’s maize fields.

Zinc-oxide (ZnO) nanostructures including nanorods are currently considered as a pioneer research of interest world-wide due to their excellent application potentials in various applied fields especially for the improvement of energy harvesting photovoltaic solar cells (PSC). We report on the growth and morphological properties of zinc-oxide (ZnO) nanorods grown on the surface of plain zinc (non-etched and chemically etched) plates by using a simple, economical, and environment-friendly technique. We apply hot water treatment (HWT) technique to grow the ZnO nanorods and varies the process parameters, such as temperature and the process time duration. The morphological, and elemental analysis confirm the agglomeration of multiple ZnO nanorods with its proper stoichiometry. The obtained nanostructures for different temperatures with different time duration showed the variation in uniformity, density, thickness and nanonorods size. The ZnO nanorods produced on the etched zinc surface were found thicker and uniform as compared to those grown on the non-etched zinc surface. This chemically etched Zinc plates preparation can be an easy solution to grow ZnO nanorods with high density and uniformity suitable for PSC applications such as to enhance the energy conversion efficiency of the photovoltaic (PV) solar cells towards the future sustainable green earth.

The structure of self-reinforced composites (SRCs) based on ultra-high molecular weight 21 polyethylene (UHMWPE) was studied by means of Wide-Angle X-Ray Scattering (WAXS), X-Ray 22 tomography, Raman spectroscopy, Scanning Electron Microscopy (SEM) and in situ tensile testing 23 in combination with advanced processing tools like Avizo, ImageJ, and Ncorr to determine the cor-24 relation between the processing conditions, on the one hand, and the molecular structure and 25 mechanical properties, on the other. SRCs were fabricated by hot compaction of UHMWPE fibers at 26 different pressure and temperature combinations without addition of polymer matrix or softener. 27 It was found by WAXS that higher compaction temperatures led to more extensive melting of 28 fibers with the corresponding reduction of the Herman’s factor reflecting the degree of molecular 29 orientation, while the increase of hot compaction pressure suppressed the melting of fibers within 30 SRCs at a given temperature. X-Ray tomography proved the absence of porosity while polarized 31 light Raman spectroscopy measurements for both longitudinal and perpendicular fiber orienta-32 tions showed qualitatively the anisotropy of SRC samples. SEM revealed that the matrix was 33 formed by interlayers of molten polymer entrapped between fibers in SRCs. Moreover, in situ 34 tensile tests demonstrated the increase of Young’s modulus and tensile strength with increasing 35 temperature.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

Nicastrin (NICT) is a transmembrane protein physically associated with the polytypical aspartyl protease presenilin that plays a vital role in the correct localization and stabilization of presenilin to the membrane-bound γ-secretase complex. This complex is involved in the regulation of a wide range of cellular events including cell signaling and the regulation of endocytosed membrane proteins for their trafficking and protein processing. Mehtods: In Trypanosoma cruzi, the causal agent of the Chagas disease, an NICT-like protein (Tc/NICT) was identified with a short C-terminus orthologous to the human protein, a large ectodomain (ECD) with numerous glycosylation sites and a single core transmembrane domain containing a putative TM-domain (457GSVGA461) important for the γ-secretase complex activity. Results: Using the Spot-synthesis strategy with Chagasic patient sera, five extracellular epitopes were identified and synthetic forms were used to generate rabbit anti-Tc/NICT polyclonal serum that recognized a ~72-kDa molecule in immunoblots of T. cruzi epimastigote extracts. Confocal microscopy suggests that Tc/NICT is localized in the flagellar pocket, which is consistent with data from our previous studies with a T. cruzi presenilin-like protein. Phylogenetically, Tc/NICT was localized within a subgroup with the T. rangeli protein that are clearly detached from the other Trypanosomatidae such as T. brucei. These results, together with a comparative analysis of the selected peptide sequence regions between the T. cruzi and mammalian proteins suggest a divergence from the human NICT that might be relevant to Chagas disease pathology. As a whole, our data show that an NICT-like protein is expressed in the infective and replicative stages of T. cruzi and may be considered further evidence for a γ-secretase complex in trypanosomatids.

The tribological performance of metalwork steel tools is of vital importance in both cold and hot working processes. One solution for improving metal tool life is the application of coatings. This paper investigates the effect of CrAlSiN thin-film PVD-deposition on the tribological behaviour of tool steel K340. The sliding wear performance of the coated K340 steel is analysed in relation to both the uncoated K340 steel and a range of tool steels dedicated to hot- and cold-working, such as X155CrVMo12-1, X37CrMoV5-1, X40CrMoV5-1, 40CrMnMo7 and 90MnCrV8. The investigated tool steels were heat-treated, while K340 was subjected to thermochemical treatment and then coated with a CrAlSiN hard film (K340/CrAlSiN). The hardness, chemical composition, phase structure and microstructure of steels K340 and K340/CrAlSiN are examined. Tribological tests were conducted using the ball-on-disc tester in compliance with the ASTM G99 standard. The tests were performed under dry unidirectional sliding conditions, using an Al2O3 ball as a counterbody. The wear factor and coefficient of friction are estimated and analysed with respect to hardness and alloying composition of the materials under study. SEM observations are made to identify the sliding wear mechanisms of the analysed tool steels and PVD-coated K340 steel. In contrast to the harsh abrasive-adhesive wear mechanism observed for uncoated tool steels, the abrasive wear dominates in case of the AlCrSiN. The deposited thin film effectively prevents the K304 substrate from harsh wear severe degradation. Moreover, thanks to the deposited coating, the K304/CrAlSiN sample has a COF of 0.529 and a wear factor of K=5.68×10−7 m3 N−1 m−1, while the COF of the reference tool steels ranges from 0.702 to 0.885 and their wear factor ranges from 1.68×10−5 m3 N−1 m−1 to 3.67×10−5 m3 N−1 m−1. The CrAlSiN deposition reduces the wear of the K340 steel and improves its sliding properties, which makes it a promising method for prolonging the service life of metalwork tools.

Ti-Al alloy phase layer/Ti-Al carburizing composite coating was prepared on the surface of titanium alloy by the stepwise coating method of hot dip aluminization and then carburizing. The weight gain results of the composite coating showed that the titanium alloy coated with the composite coating had long-term stability (≥16 days) at 800oC. The microstructure, phase structure and composition of the composite coating were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).The composite coating is composed of an alloy phase layer and a carburized layer. The natural transition of four phases (Ti3Al/TiAl/TiAl2/TiAl3) in the alloy phase layer, significantly improves the interfacial bonding between the coating and the substrate, and slows down the propagation of microcracks through the coating.Al2O3, TiC and C in the carburizing layer improve the surface hardness of the coating, and TiAl2 and Al2O3 also have excellent oxidation resistance at high temperature.

A new lateral force-resisting wall panel is presented for applications in mid-rise prefabricated lightweight steel construction in seismic prone regions. This panelised system is composed of a hot-rolled frame and cold-formed studs and tracks, which works as a lateral force resisting system in lightweight steel framing. The proposed hybrid panel system exhibits proper ductility and energy dissipation behaviour. The hysteretic responses of full-scale panel experiments demonstrate that the system can safely resist high cyclic loads. The hot-rolled steel part, on the other hand, can significantly improve the initial lateral stiffness of the total system that will control the maximum allowable drift of multi-story buildings. Finally, in a case study, by applying the proposed system to the design of a mid-rise building in a high seismic area, the performance of the hybrid panels, are compared with those of fully hot-rolled systems (moment resisting frames) and fully cold formed systems. The findings indicate that applying hybrid panels will result in lower weights and better performance in seismic prone regions.

Human Face and facial parts are the most significant parts as it reveals a person’s true identity. It plays an important role in various biometric applications like crowd analysis, human tracking, photography, cosmetic surgery, etc. There are many techniques are available to detect a facial image. Among them, skin detection is the most popular one. The aim of this paper is to detect first the person's identity from facial image and finally check any spot present the the detected person. The first step is to detect the maximum skin region based on a combination method of RGB and HSV color space model. Next it is to verify the skin areas of human through machine learning approach. The Aggregated Channel Features (ACF) detector is used to identify the different facial parts like eye pairs, nose, and mouth. Bootstrap aggregation decision tree classifier is applied to classify the person’s identity based on Histogram Oriented Gradient (HOG) features value. The experimental results show that the proposed method gives the average 97% accuracy.

Rapid developments in the field of underwater photogrammetry have given scientists1the ability to produce accurate 3-dimensional (3D) models which are now increasingly used in the representation and study of local areas of interest. This paper addresses the lack of systematic analysis of 3D reconstruction and navigation fusion strategies, as well as associated error evaluation of models produced at larger scales in GPS-denied environments using a monocular camera (often in deep-sea scenarios). Based on our prior work on automatic scale estimation of Structure from Motion (SfM)-based 3D models using laser scalers, an automatic scale accuracy framework is presented. The confidence level for each of the scale error estimates is independently assessed through the propagation of the uncertainties associated with image features and laser spot detections using a Monte Carlo simulation. The number of iterations used in the simulation was validated through the analysis of the final estimate behaviour. To facilitate the detection and uncertainty estimation of even greatly attenuated laser beams, an automatic laser spot detection method, mitigating the effects of scene texture, was developed, with the main novelty of estimating the uncertainties based on the recovered characteristic shapes of laser spots with radially decreasing1 intensities. The effects of four different reconstruction strategies resulting from the combinations of Incremental/GlobalSfM, and thea priori/a posterioriuse of navigation data were analyzed using two distinct survey scenarios captured during the SUBSAINTES 2017 cruise (doi: 10.17600/17001000). The study demonstrates that surveys with multiple overlaps of non-sequential images result in a nearly identical solution regardless of the strategy (SfM or navigation fusion), while surveys with weakly connected sequentially acquired images are prone to produce broad-scale deformation (doming effect) when navigation is not included in the optimization. Thus the scenarios with complex survey patterns substantially benefit from using multi-objective BA navigation fusion. In all cases, the errors in the models are inferior to 5%, with errors often being around 1%. The effects of combining data from multiple surveys were also evaluated. The introduction of additional vectors in the optimization of multi-survey problems successfully accounted for offset changes present in the underwater USBL-based navigation data and thus minimize the effect of contradicting navigation priors. Our results also illustrate the importance of collecting a multitude of evaluation data at different locations and moments during the survey.

This research aims to estimate the micro-motion (m-m) of ships. The problem of motion and m-m detection of targets is usually solved using synthetic aperture radar (SAR) along-track interferometry (ATI) which is observed employing two radars spatially distanced by a baseline extended in the azimuth direction. This paper is proposing a new approach where the m-m estimation of ships, occupying thousands of pixels, is measured processing the information given by sub-pixel tracking generated during the coregistration process of several re-synthesized time-domain and overlapped sub-apertures. The SAR products are generated splitting the raw data, according to a small-temporal baseline strategy, observed by one single wide-band staring spotlight (ST) SAR image. The predominant vibrational modes of different ships are estimated and results are promising to extend this application in performing surveillance also of land-based industries activities. Experiments are performed processing one ST SAR image observed by the COSMO-SkyMed satellite system.

This study introduces a remote sensing application using satellite imagery to survey a network-scale aggregate stockpile inventory. First, a real scale aggregate quarry site was surveyed using a small Unmanned Aerial Vehicle (sUAV) to produce digital terrain models that enabled analysis of aggregate pile geometry. Second, a lab experiment was designed and performed to validate the applicability of close-range Structure from Motion (SfM) photogrammetry for measuring aggregate piles' physical properties such as volume and density. The other part of the lab experiment delved into direct measurement of aggregate density under varying compaction efforts. These experimental results, in conjunction with some simplifying assumptions, enabled the calculation of aggregate stockpile volumes and estimated weights from satellite imagery. We estimated that an inventory of 4.4 and 1.1 million metric tons of crushed aggregates and Reclaimed Asphalt Pavement (RAP), respectively, stockpiled in Washington State for asphalt production in 2017. The merit of producing such database was further showcased in an example on the economic and environmental impacts of material transportation. We approximated that hauling aggregates from quarry plants to construction sites within Washington State incurs a cost of about $50 thousand to over $4 million, consumes about 0.25 to 20 TJ of energy, and emits 20 to over 1,500 tons of CO₂-eq per asphalt plant annually.