This experimental study probes the dynamic behaviour of a 3mm ABS sheet during positive mould vacuum-assisted thermoforming. In this process, the sheet undergoes large and fast deformations, caused by the applied vacuum and mechanical stretching by the mould. The objective is to elucidate the complexities of these large, rapid and non-isothermal deformations. The non-isothermal conditions are caused by the radiative heating of the sheet, convective heat loss to the surrounding air and conductive heat transfer from the sheet to the mould. Utilizing stereo Digital Image Correlation (DIC) in tandem with thermal imaging, the present study accurately maps the occurring displacement, strain and strain rate field in relation to real-time temperature variation of the material. The study progresses to observe the ABS material from the moment it contacts the mould until it conforms to a positive 250mm diameter semi-sphere cast aluminium mould. The DIC methods are validated by comparing thickness values derived from DIC’s principal strain directions to ultrasonic thickness gauge readings. This knowledge not only broadens the understanding of the thermo-mechanical behaviour of the material but also aids in optimizing process parameters for improved thickness uniformity in thermoformed products.

The effect of the melt cooling rate on the atomic ordering of austenite and, as a consequence, on the martensitic transformation of a nonstoichiometric alloy of the Ni-Mn-In system has been studied. In-situ TEM observations revealed differences in the mechanism of phase transformations of the alloy subjected to different cooling conditions. It is shown that during quenching a high density of antiphase boundaries (APB) is formed and the alloy is in the austenite-martensitic (10M and 14M) state up to a temperature of 120K. In a slowly cooled alloy, a lower APB density is observed, and a two-stage transformation L21/B2 → 10M → 14M occurs in the range of 150–120 K.

Aquathermolysis is a promising method to upgrade heavy oil in reservoir conditions. However, application of catalysts can significantly promote transformation of the heavy fragments (resins and asphaltenes) and heteroatom-containing compounds of crude oil mixture into low-molecular-weight hydrocarbons. In this paper, the comparison study of the catalytic performance of the water-soluble metal salts such as NiSO4 and FeSO4 on the aquathermolytic upgrading of heavy oil samples produced from Ashal’cha reservoir was carried out at a temperature of 300 °C for 24 hours. Iron nanoparticles contributed to the highest viscosity reduction degree - 60% in contrast to the viscosity of the native crude oil sample. The viscosity alteration is reasoned by the changes in the group composition of heavy oil after catalytic (FeSO4) aquathermolysis, where the content of resins and asphaltenes were reduced by 17% and 7%, respectively. Moreover, the aquathermolytic upgrading of heavy oil in the presence of FeSO4 led to an increase in the yield of gasoline fraction by 13% and diesel fraction by 53%. The H/C ratio, which represents the hydrogenation of crude oil, increased from 1.52 (before catalytic upgrading) to 1.99 (after catalytic upgrading). The results of Chromatomass (GC-MS) and Fourier-infrared (FT-IR) spectroscopies confirmed the intensification of destructive hydrogenation of resins and asphaltenes in the presence of the water-soluble catalysts. According to XRD and SEM-EDX results, the metal salts are thermally decomposed during the aquathermolysis process into the oxides of corresponding metals and particularly sulfided by the sulfur-containing aquathermolysis products.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmental friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000°C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700°C, with respect to the c-axis of kaolinite. One the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface . The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C and 400 °C. Above 400°C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100 respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100 KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at lower temperature 475°C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45 ° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite obtained undergone structural transformation to another transitory phase at 1000°C.

In this paper we report on the use of an in-house developed solid-state hybrid microwave and radiofrequency generator operating at frequencies of 2.45 GHz and/or 480 kHz for cancer ablation in various tissues. The generator has demonstrated increased accuracy due to its custom-designed hardware, which incorporates the latest technologies and algorithms to control the emitted power versus temperature profile of the treated sample. In particular, the hybrid generator incorporates control systems based on impedance or reflected power measurements that allow controlled ablation without causing unwanted carbonisation and without including areas where tissue damage is not desired. Tests performed ex-vivo on chicken breast and bovine liver show that radiofrequency ablation (RFA) is very effective for performing controlled ablations with minimally invasive probes, such as cardiac pathologies, small lesions, tissues with particular composition, while microwave ablation (MWA) is optimal for performing large ablations in highly vascularised tissues, such as liver cancer, where it is necessary to achieve higher temperatures.

Drug resistance in tumor cells is a significant roadblock in the clinical management of advanced or recurrent diseases in endometrial cancers. As a part of the tumor-stromal ecosystem, tumor cells are ecologically connected to the cancer-associated fibroblasts (CAFs), which form contributory elements of the tumor microenvironment (TME). We recently reported a novel model of patient-derived CAF-based 2-cell Hybrid Co-Culture (HyCC) to evaluate CAFs' role in developing drug resistance and understanding personalized tumor cell-CAF dialogue. Using our 2-cell HyCC model of patient-derived endometrial CAFs, we present data to demonstrate the direct counter-inhibitory effect of CAFs to combinations of cytotoxic and targeted drugs in developing drug resistance. CAFs derived from resected endometrial tumor samples were first passage-wise characterized before and after freeze-thaw for their positive and negative CAF markers expression pattern. Paclitaxel and its combination with copanlisib, TAK228, lenvatinib, and trametinib were used to test the 3D clonogenic growth of endometrial AN3CA cells on endometrial CAFs. We demonstrate that CAF-mediated resistance to antitumor drugs occurs via direct and indirect contact with CAFs in HyCC. Our data established the strength of the 2-cell HyCC model of patient-derived CAFs in solid tumors and provided a model of resistance to antitumor drugs tailored on a patient-to-patient basis.

Due to the low content, few studies are focused on the volatile compounds of Phlomoides rotata (Benth. ex Hook. f.) Mathiesen (PR, syn. Lamiophlomis rotata (Benth.) Kudô). However, such volatile compounds may have important pharmacological activities such as antioxidant, anticancer. In order to identify the chemical markers (CMs) in the essential oils (Es) and explore the potential bioactivities, we first conduct a thoroughly investigation on the volatile compounds and evaluate their anti-oxidant activities (AOAs), to the best of our knowledge. Light yellow Es with a fresh and elegant smell are obtained by hydro-distillation with an average yield of 0.11% (mL/g). After separation through cryoprecipitation, the crystals (Cs) and EOs removed crystals (RCs) were gotten, respectively. A total of 81 components are qualified and quantified in the Es, Cs and RCs, in which 44 ones are first reported from PR. As for content, the main compounds are long-chain fatty acids (LCFAs) and their esters. Among them, palmitic acid (PA), myristic acid (MA), linoleic acid (LA), oleic acid (OA) and methyl palmitate are highlighted, Besides, hexahydrofarnesyl acetone and phytol are also prominent Four kinds of C13-norisoprenoids are first reported from PR, in which, trans-β-damascenone is potent in flavour. In sum, these eight representative compounds can be chosen as the CMs. The AOAs of Es, Cs, RCs and four CMs such as PA, MA, LA and OA are evaluated by in vitro assays. In general, PA and MA present pro-oxidant activities (POAs) or weak AOAs. LA and OA show POAs or weak AOAs in lower concentration group, whereas demonstrate medium or strong AOAs in higher concentration group. Usually, the RCs demonstrate stronger AOAs and the Cs present weaker AOAs compared with those of the corresponding Es, which should be related to their different content of PA. This study can give some hints on the utilization of such Es which are abundant in LCFAs.

Migraine is a debilitating neurovascular disorder characterized by recurrent headache attacks of moderate to severe intensity. Calcitonin gene-related peptide (GGRP), which is abundantly expressed in trigeminal ganglion (TG) neurons, plays a crucial role in migraine pathogenesis. Cortical spreading depolarization (CSD), the biological correlate of migraine aura, activates the trigeminovascular system. In the present study, we investigated CGRP mRNA expression in TG neurons in a CSD-based mouse migraine model. Our in situ hybridization analysis showed that CGRP mRNA expression was observed in smaller neuronal populations. CSD did not significantly change the density of CGRP mRNA-synthesizing neurons in the ipsilateral TG. However, the cell sizes of CGRP mRNA-synthesizing TG neurons were significantly larger in the 48 h and 72 h post-CSD groups than in the control group. The proportions of CGRP mRNA-synthesizing TG neurons bearing cell diameters less than 14 μm became significantly less at several time points after CSD. In contrast, we found significantly greater proportions of CGRP mRNA-synthesizing TG neurons bearing cell diameters of 14–18 μm at 24 h, 48, and 72 h post-CSD. We deduce that the CSD-induced upward cell size shift in CGRP mRNA-synthesizing TG neurons might be causative of greater disease activity and/or less responsiveness to CGRP-based therapy.

In this communication, we present a new simulated in situ lab/on-deck incubator, light spectrum replicator (LSR), and method to simulate the measured in situ HOCR light spectrum curves in incubation chambers. Carbon flux studies require detailed knowledge of primary and secondary production, including an understanding of temporal and spatial scales of variation. Interpretation of the processes involved during measurements continues to be difficult [1] since the incubation of the samples does not permit the study of rapid variations in carbon assimilation. Further, the significance of Dissolved Organic Matter of DOM in primary production is gaining attention as many autotrophic species are known for using organic substrates for growth, even in the dark [2–4] and since a significant portion of DOM can be accounted for from active release of intracellular metabolites by microbial consortia [5]. On the other hand, the major uncertainties in bacterial production measurements lie with the conversion factors used to calculate bacterial production (BP). For a given thymidine incorporation rate, estimates of BP can range by a factor of more than 20 [6,7]. Even though various new analytical tools have emerged [8], understanding of complex patterns of interactions within the microbial loop remains an open question.

Acid in-situ leaching (ISL) is a common approach to the recovery of uranium in the subsurface. As some toxic and harmful substances might be produced by the chemical reactions among the injected sulphuric acid, the groundwater, and the porous media during leaching processes, the pollution control of the mining plan for ISL is important. In this study, a three-dimensional reactive transport modeling (3DRTM) was applied to decide the pollution control mining plan, considering the partial penetration through wellbore in confined aquifer and complex chemical reactions between main minerals. Based on the 3DRTM, different pumping ratio and non-uniform injection schemes were compared. The results show that the preferential pollution control mining plan is non-uniform injection ratio equal 0.1. By analyzing the characteristics of water table and streamline, it is concluded that the scheme has a strong hydraulic capture effect. In this scheme, the concentration of UO22+, H+, SO42- obtained by 3DRTM is lower. The inner well injection rate is 194.09 m3/d, the outer well injection rate is 158.89 m3/d, and the pumping rate is 264.00 m3/d. A reasonable suggestion is to adopt non-uniform injection mining mode in ISL.

The goal of this study was to characterize the initial growth trajectory of Epicrates assisi, 1 Epicrates cenchria, and Epicrates crassus snakes raised in captivity. An exponential model with 2 parameters for birth weight (A) and growth rate (k) was fitted for each animal. There was a significant 3 difference A and k among the three species, the means (standard error) for A and k parameters were 4 31 (0.3) g and 0.0027 (0.00006) for E. assisi, 27.6 (0.6) g and 0.0046 (0.00013) for E. cenchria and 25.9 5 (1.4) g and 0.0033 (0.00027) for E. crassus. We showed a significative variability between species for 6 initial growth trajectory. In addition, we also demonstrated the existence of variability within species, 7 which can be used to change the growth trajectory of snakes, being a tool for selection and genetic 8 improvement.9

This study aimed to evaluate the diagnostic roles of various immunohistochemical markers in urothelial carcinoma in situ (uCIS) through a meta-analysis and review of diagnostic test accuracy. Immunohistochemical markers CK20, CD44, AMACR, and p53 were evaluated in the present study. We analyzed the expression rates of immunohistochemical markers and compared their diagnostic accuracies. The estimated expression rates were 0.803 (95% confidence interval [CI]: 0.726–0.862), 0.142 (95% CI: 0.033–0.449), 0.824 (95% CI: 0.720–0.895), and 0.600 (95% CI: 0.510–0.683) for CK20, CD44, AMACR, and p53, respectively. In the comparison between uCIS and reactive/normal urothelium, the expression of CK20, AMACR, and p53 in uCIS was significantly higher than in reactive/normal urothelium. CD44 showed significantly lower expression in uCIS than in the reactive/normal urothelium. Among the markers, AMACR had the highest sensitivity, specificity, and diagnostic odds ratio. The AUC on SROC was the highest for CK20. In conclusion, immunohistochemical markers, such as CK20, CD44, AMACR, and p53, can be useful in differentiating uCIS from reactive/normal urothelium.

Laser in situ keratomileusis (LASIK) is the gold standard in the surgical correction of refractive errors on the cornea. It entails the creation of a superficial hinged corneal flap by a femtosecond laser, ablation of the underlying stromal bed by an excimer laser, and reposition of the flap. The corneal flap can be build in a 2-dimension (2D) fashion with tapered edges, or in a 3-dimension (3D) fashion, with angled sidecut. The latter reduces the risk of flap dislocation and infiltration of epithelial cells. This retrospective study compares with optical coherence tomography 3D and 2D flaps, and respective intra- and early post-operative complications. Four hundred consecutive eyes were included, 200 for each group. In the 3D group, the mean edge angle was 92°. The procedure was in average 5.2 seconds slower in the 3D group (p=0). Non visually significant flap folds were found in 13 eyes of the 2D group and in 7 eyes of the 3D group (p= 0.17). An intracorneal opaque bubble layer induced by laser photodisruption was more commonly observed in the 3D group (9 eyes vs. 2; p=0.03). In conclusion, the creation of a LASIK flap by a 3D-femtosecond laser cut was safe and effective.

The (Ti, Nb)(C, B)/IN625 composite coating with both homogeneous and defect-free microstructure were successfully prepared by in situ on the surface of 42CrMo steel using the coupling of the ultra-high-speed laser cladding (EHLA in German) technology with the direct reaction synthesis (DRS) technology, and were comparatively analyzed with the IN625 coating prepared by the EHLA. The microstructure of the fused cladding layer was investigated by selected scanning electron microscopy (SEM), energy dispersive spectrometer (EDS) and double spherical aberration transmission electron microscopy (DSA-TEM). The residual stress distribution on both sides of the fused cladding interface was characterised by nanoindentation stress test based on the modified O&P method and the G&S energy method. The results show that the interface of (Ti, Nb)(C, B)/IN625 composite coatings is affected by about 670 kJ Joule heat released from the in-situ reaction, and the interfacial width reaches 24 μm, so that it is 6 times higher than that of IN625 coating prepared by EHLA, which effectively reduces the stress gradient in the interfacial region and alleviates the stress mismatch on both sides of the interface. However, the surface hardness of (Ti, Nb)(C, B)/IN625 composite coating is lower than that of the IN625 coating, with a value of about 240 HV0.2, and the average wear weight loss was only 10% of that of the IN625 coating, which is on the one hand attributed to the in-situ authigenic TiCB, TiC, NbMo3B4, and NbMo2B2 phases supporting the (Ti, Nb)(C, B)/IN625 composite coating substrate to achieve the abrasion reduction and wear resistance. On the other hand, it is attributed to the formation of nano-equiaxial ultrafine grains in the depth range of 250 nm below the wear surface area by the coupling of the three fields of plastic rheology-heat-force, which dynamically strengthens the wear surface.

Accurate determination of protein localization, levels, or protein-protein interactions is pivotal for the study of their function, and in situ protein labeling via homologous recombination has emerged as a critical tool in many organisms. While this approach has been refined in various model fungi, the study of protein function in most plant pathogens has predominantly relied on ex-situ or overexpression manipulations. To dissect the molecular mechanisms of development and infection for Verticillium dahliae, a formidable plant pathogen responsible for vascular wilt diseases, we have established a robust, homologous recombination-based in situ protein labeling strategy in this organism. Utilizing Agrobacterium tumefaciens-mediated transformation (ATMT), this methodology facilitates the precise tagging of specific proteins at their C-termini with epitopes, such as GFP and Flag, within the native context of V. dahliae. We demonstrate the efficacy of our approach through the in situ labeling of VdCf2 and VdDMM2, followed by subsequent confirmation via subcellular localization and protein-level analyses. Our findings confirm the applicability of homologous recombination for in situ protein labeling in V. dahliae and suggest its potential utility across a broad spectrum of filamentous fungi. This labeling method stands to significantly advance the field of functional genomics in plant pathogenic fungi, offering a versatile and powerful tool for the elucidation of protein function.

Mesenchymal stem cells (MSCs), whose main function is tissue repair, use collagen to restore the structural integrity of damaged tissue, maintaining its organization through concomitant remodelling. The non-enzymatic glycation of collagen is likely to compromise its communication with MSC, which indeed underlies various pathological conditions such as late complications of diabetes and aging. However, data on the effect of more early stages of collagen glycation on the MSC interaction are lacking. This study focused on the fate of in vitro glycated rat tail collagen (RTC) in contact with MSCs after its pre-exposure to glucose for 1 or 5 days. Using human adipose tissue-derived MSCs (ADMSCs), we showed that their interaction with glycated collagen is significantly altered, manifested morphologically by reduced cell spreading, less formation of focal adhesions, and weaker development of the actin cytoskeleton, further confirmed by ImageJ morphometric analysis. This suggests a poorer recognition of early glycated collagen by integrin receptors, possibly due to steric hindrance of their binding sites. These morphological events were also accompanied by greatly reduced fibril-like reorganization of adsorbed FITC-collagen (a sign of impaired remodeling), complemented by reduced sensitivity to proteases. The latter was confirmed in two ways: measuring directly FITC-collagen degradation by the attached cells and quantifying the proteolysis reduction upon exogenous addition of collagenase in a cell-free system. The mechanism of the observed effects is unclear, although differential scanning calorimetry confirmed the presence of weak structural changes in glycated collagen. All this led us to conclude that the reason for the morphological changes of ADMSCs is the impaired interaction with early-glycated collagen due to the hindrance of complementary sequences for integrins, which certainly also affects the mechanical remodeling of collagen. However, the impaired collagenolytic activity, together with the observed small changes in the thermal transition profile, undoubtedly indicate some internal changes in the structural organization of the collagen molecule occurring even at this early stage of glycation, which in turn contributes further to the impaired MSC remodeling activity.

The chemical reaction of ion-adsorption type rare earth during in-situ leaching process is accompanied by ion migration and charge movement, making the leaching process electrochemical in nature. The chemical reaction rate plays an important role in the leaching rate of rare earth elements. In this work, electrochemical impedance spectroscopy (EIS) was used to reveal characteristics of electrical resistance alteration and leaching rate of rare earth elements during in-situ leaching. The equivalent circuit model of the leaching process was established, and two critical parameters of solution resistance Rs and charge transfer resistance Rt were analyzed to reflect the electrochemical characteristics. According to the characteristics of electrical resistance alteration, the leaching process was divided into four stages: wetting, reaction, equilibrium, and top water stage. The resistance parameters Rs and Rt decreased first and then increased during the leaching process. The maximum value of Rs was 1330Ω∙cm2 at the end of the top water stage, and the minimum value was 135Ω∙cm2 at the beginning of the equilibrium stage. The maximum value of Rt was 8310Ω∙cm2 at the beginning of the leaching stage, and the minimum value was 21Ω∙cm2 at the end of the reaction stage. Rs and Rt were negatively correlated with the pore size and chemical reaction rate during leaching. With increasing of pore size and reaction rate , the resistance parameter decrease. This study provide a new idea for intelligent monitoring of rare earth ore.

The Dongtangzi large Zn-Pb deposit is located in the southwest of the Fengxian-Taibai (abbr. Fengtai) ore cluster in the west Qinling orogen, whose origin has been controversial, positing diverse genesis mechanisms such as sedimentary-exhalative (SEDEX), sedimentary-reformed, and epigenetic hydrothermal type. In this work, based on detailed observation and systematic study on ore geology, the results of high-precision Rb-Sr isotopic dating on sulfides of the main orebody and Sm–Nd isotopic dating on associated carbonates have been carried out, which yield isochron ages of 211.6 ± 2.6 Ma and 211 ± 4 Ma, respectively. In-situ S-Pb isotopic studies show that the ore related sulfides display a narrow range of δ³⁴S values from 1.1 ‰ to 10.2 ‰, with ²⁰⁶Pb/²⁰⁴Pb, ²⁰⁷Pb/²⁰⁴Pb and ²⁰⁸Pb/²⁰⁴Pb ratios of 18.07 to 18.27, 15.64 to 15.66, and 38.22 to 38.76, respectively. While the pyrite of sedimentary period and the granite porphyry dike have δ³⁴S values vary from 15.8 to 21.4‰, and from 2.1 to 4.3‰ (with ²⁰⁶Pb/²⁰⁴Pb ratios of 18.09 to 18.10, ²⁰⁷Pb/²⁰⁴Pb ratios of 15.59 to 15.61, and ²⁰⁸Pb/²⁰⁴Pb ratios of 38.17 to 38.24) respectively. Combining the regional geology, we propose that the Dongtangzi Zn-Pb deposit is the product of multi-stage epigenetic hydrothermal fluid processes, driven by late Triassic regional tectono-magmatic activities in regional extensional regime, with metallic materials originate from a mixture of Triassic magmatic processes and metamorphic basement.

The effects of chemical composition and solidification rate on the solidification behavior of high-Cr white irons were investigated through directional solidification. Increasing the solidi-fication rate in hypoeutectic alloys caused the finer dendrite arm spacing as expected. The eutec-tic structure which formed in the interdendritic region comprised of M7C3 and austenite, how-ever, secondary dendrite arms of hypoeutectic alloys contained a few M7C3 particles that solidi-fied prior to the eutectic structure. The transition from cellular to dendritic solidification oc-curred at a solidification rate between 50 µm/s and 100 µm/s in a near eutectic alloy. In the near eutectic alloy with cellular solidification, a directionally arrayed in-situ composite of M7C3/austenite formed within the cell. Speckle-like feature appeared in the intercellular region due to M23C6 carbide precipitation during subsequent cooling after freezing. Like dendrite arm spacing in hypoeutectic alloys, the inter-speckle spacing and the inter-fibre spacing became finer with increasing solidification rate in the cellular solidification range.

Excess consumption of a high-fat diet has been identified as one of the contributing factors for obesity. Women are at higher risk for adult obesity than men, predisposing them to a different set of detrimental disease conditions. Furthermore, aging studies show that physiological decline also has a serious impact on changes in the endocrine properties of white adipose tissue. Howev-er, there is still relatively little known about the factors associated with obesity and aging and their compounding impact on women’s health. To investigate adipocytokine secretion profile changes, female C3H/HeJ mice were induced to obesity through long-term consumption of a high-fat diet. Weight gain measurements and Echo MRI analysis of fat composition showed in-creases were a due solely to the high fat content in the diet. Adipocytokine secretions were ana-lyzed in media conditioned from harvested visceral fat tissue that was organ cultured ex-vivo. Adipocytokine analysis across diets and age showed significant increases in Adiponectin and Leptin secretion in high-fat diets, accelerated increases in Resistin secretion with high-fat diets. Aging induced increased secretion of Lipcalin-2, Pentraxin-3 and Serpin E1, MCP-1 and ICAM-1, regardless of diet. Furthermore, comparisons of organoid cultured protein secretions and flash-frozen tissue samples differed greatly, suggesting the WAT organoid cultures may yield information more reflective of in situ conditions. Taken together, our results show that diet and aging significantly impact secretions from adipose tissue, that may contribute to women’s health issues.

A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitable homogenization temperature and duration is a crucial step in assuring a homogeneous distribution of alloying elements and optimal exploitation of the potential of the alloy. In-situ heating in an electron microscope was performed on a twin-roll cast Al-Cu-Li-Mg-Sc-Zr alloy to understand the peculiarities of the homogenization process. Four types of primary phase particles rich in Cu, Li, Mg, and Fe were identified in the as-cast material. They appear as coarse particles at the boundaries of eutectic cells. Their partial dissolution occurs at temperatures above 450 °C. They are almost fully dissolved at 550 °C, except for complex phases containing Fe and Cu. Small dimensions of eutectic cells in the range of 10 µm assure a homogeneous distribution of main alloying elements within the matrix after 20 min of annealing. Direct comparison with the same material prepared by mold-casting indicates that such short annealing times result in the dissolution of main primary phase particles but do not assure a homogeneous distribution of alloying elements in the whole volume of the specimen.

In drilling small holes with diameters of 1 mm or less, minute clogging and twining of chips or adhesion of the workpiece material can become factors in causing breakages of the drill bit; moreover, it can be difficult to identify the machining state. Acoustic emission (AE) sensing is a nondestructive inspection technique that measures the elastic-stress waves that are generated when a material is deformed and fractured. AE sensing permits highly sensitive measurements to be made without changing the rigidity of the experimental system, unlike force sensing of cutting resistance, etc. In the present study, attempts were made to identify the machining state and tool wear, and to predict abnormalities in small-diameter drilling by using the change in the frequency of AE signal waveforms arising from deformation and fracture. It was shown that it is possible to predict the breakage of the drill bit by detecting the high-frequency AE signals caused by adhesion. In addition, a correlation map of the AE frequency spectrum for identifying the machining state in a drilling operation is suggested.

The assessment of concrete structures' durability in chlorine environments is significantly impacted by the uncertainty inherent in existing durability models. It introduce an integrated approach for updating these models, based on detection information of existing structures. This approach narrows the gap between theoretical predictions and observed structural durability. Specifically, we refine the probability model of critical chloride content by analyzing steel bar corrosion sample proportions, using Bayesian theory for greater accuracy. The enhanced model enables more reliable life expectancy prediction, forming a solid foundation for maintaining and strengthening existing structures.This method was demonstrated through a case study of a reinforced concrete industrial building with a service life of 12 years.

Abstract Octreotide is the first synthetic peptide hormone, consisted of eight amino acids, that mimics the activity of somatostatin, a natural hormone in the body. During the past decades, advanced instrumentation and crystallographic software established X-ray Powder Diffraction (XRPD) as a valuable tool for extracting structural information of biological macromolecules. The latter was demonstrated by the successful structural determination of octreotide at a remarkably high d-spacing resolution (1.87 Å) (PDB code: 6vc1). This study focuses on the response of octreotide to different humidity levels and temperatures, with a particular focus on the stability of the polycrystalline sample. XRPD measurements were accomplished employing an Anton Paar MHC-trans humidity-temperature chamber installed within a laboratory X’Pert Pro diffractometer (Malvern Panalytical). The chamber is employed to control and maintain precise humidity and temperature levels of samples during XRPD data collection. Pawley analysis of the collected data sets revealed that the octreotide polycrystalline sample is remarkably stable and no structural transitions were observed. The compound retains its orthorhombic symmetry (space group: P212121, a = 18.57744(4) Å, b = 30.17338(6) Å, c = 39.70590(9) Å, d~ 2.35 Å). However, a characteristic structural evolution in terms of lattice parameters and volume of the unit-cell is reported mainly upon controlled relative humidity variation. In addition, an improvement of signal-to-noise ratio in the XRPD data under a cycle of dehydration/rehydration is reported. These results underline the importance of considering the impact of environmental factors, as humidity and temperature, in the context of structure-based drug design, thereby contributing to the development of more effective and stable pharmaceutical products.

Land surface temperature (LST) is a crucial parameter in climate and ecology, exerting significant influence on meteorological conditions, ecosystems, and human life. LST data sources are diverse, with remote sensing being the prevailing means of acquisition. FY-4A/AGRI offers high-quality LST products for East Asia. In this study, we evaluated the performance of the product in Hunan Province and conducted refined analysis of surface heat resources based on the 4km/1h resolution product over a two-year period. The results demonstrate that the FY-4A LST product effectively captures surface temperature (R=0.893), albeit with a relatively high error level (Bias=-6.295℃; RMSE=8.58℃), particularly in capturing high LST values. The performance of this product is superior in the eastern flat terrain area of Hunan Province compared to its performance in the western mountainous region due to environmental conditions causing systematic errors that contribute to instability in detection deviation for this product. Surface heat resources are more abundant in eastern Hunan Province than in mountainous areas located west and southwardly, and the detailed distribution of them at finer scales is mainly influenced by the terrain and climate conditions. There is no obvious seasonal difference in the distribution of heat resources except in winter, and rapid urbanization within Chang-Zhu-Tan urban agglomeration during two years has significantly altered the spatial distribution pattern of surface heat resources across Hunan Province. These findings provide a quantitative baseline for assessing FY-4A satellite's detection capability while serving as a reference for further application of its LST products and establishing foundations for divisional classification and utilization strategies pertaining to surface heat resources within Hunan Province.

Background: Radiotherapy in the head-and-neck area is one of the main curative treatment options. However, this comes at the cost of varying levels of normal tissue toxicity, affecting up to 80% of patients. Mucositis can cause pain, weight loss and treatment delay leading to worse outcomes and decreased quality of life. Therefore, there is an urgent need for an approach to predict normal mucosa response in patients prior to treatment. Methods: We here describe an assay to detect irradiation response in patient healthy oral mucosa tissue. Mucosa specimens from the oral cavity were obtained after surgical resection, cut into thin slices, irradiated, and cultured for three days. Seven samples were irradiated with X-ray and three additional samples were irradiated with both X-ray and protons. Results: Healthy oral mucosa tissue slices maintained normal morphology and viability for three days. We measured a dose-dependent response to X-ray irradiation and compared X-ray and proton irradiation in the same mucosa sample, using standardized automated image analysis. Furthermore, increased levels of inflammation inducing factors - major drivers in mucositis development - could be detected after irradiation. Conclusion: This model can be utilized for investigating mechanistic aspects of mucositis development and can be developed into an assay to predict radiation-induced toxicity in normal mucosa.

In-situ observation on the austenite grain growth and martensite transformation in a developed NM500 wear-resistant steel were conducted on a Confocal Laser Scanning High-temperature Microscope (CSLM). Results indicated that the martensite nucleation did not synchronously proceed during quenching process. The selective prenucleation dominated in martensite nucleation, which dividing untransformed austenite into several regions, and resulting in the larger size of fresh martensite. Martensite can not only nucleate at parent austenite grain boundaries, but also nucleate in the preformed martensite laths and twins. Smaller constraint in the martensite growth was achieved in a larger parent austenite grain size, leading to the longer fresh martensite and secondary martensite. Besides, the transformation kinetics of martensite was accelerated in a higher quenching temperature. Moreover, the martensitic laths presented in parallel laths (0~2°) based on the pre-formed lath or distributed in triangle, parallelogram or hexagon with an angle of 60° or 120°. Interestingly, martensitic lath also traversed the unstable new parent austenitic grain boundaries. In addition, the size of austenite grains increased with the quenching temperature, and austenite grains coarsened in a short time at a higher quenching temperature of 1160 ℃. Furthermore, a large amount fine dispersed particles redissolved and ripped at 1160 ℃, resulting in the many large and visible carbonitrides.

The in vitro cultivation of M. leprae has not been possible since it was described as causing leprosy, and the limitation of animal models for clinical aspects makes studies on leprosy and bacteria-human host interaction a challenge. Our aim was to standardize the ex vivo skin model (hOSEC) to maintenance and study of M. leprae as an alternative animal model. Bacillary suspensions were inoculated into human skin explants and sustained in DMEM medium until 60 days. Explants were evaluated by RT-PCR-16SrRNA, and cytokines gene expression. Viability and infectivity of bacilli recovered from explant (D28 and D60) were evaluated using the Shepard’s model. All explants were RT-PCR-16srRNA positive. Viability and infectivity of recovered bacilli from explants, analyzed after 5 months of inoculation in mice showed an average positivity of 31%, being the highest positivity in the D28 groups (80%). Furthermore, our work showed different pattern in cytokines gene expression (TGF-β, IL-10, IL-8 and TNF-α) in the presence of alive or dead bacilli. Although changes can be made for improve future experiments, our results have demonstrated that it is possible to use the hOSEC to maintain M. leprae for 60 days, interacting with the host system, an important step in the development of experimental models for studies on the biology of the bacillus, its interactions, and drug susceptibility.

The Double U-pipe ground heat exchanger, recognized for its straightforward process, cost-effectiveness, high heat exchange efficiency, and low thermal resistance, stands as the predominant ground heat exchanger type in today's shallow geothermal energy development and utilization. Recent years have seen significant research into the heat transfer influencing factors and heat exchange performance of Double U-pipe ground heat ex-changers via experimental testing methods. Yet, studies integrating numerical simulation with in-situ testing have been less frequent. Drawing on the cylindrical heat source model theory and the outcomes of regional in-situ thermal response tests, this paper develops a Double U-pipe ground heat transfer model by establishing physical, mathematical, and heat transfer geometric models. It assesses the impact of varying inlet temperatures, flow rates, and initial ground temperatures on heat exchange efficiency under heating conditions. The results validate the precision of the double U-pipe ground heat exchanger model based on in-situ testing. They show that enhancing the temperature differential between the inlet and initial temperatures, elevating the initial ground temperature, and moderately increasing the flow rate can boost the system's heat exchange efficiency.

In the most cases, invasive ductal carcinoma (IDC) of the breast is identifiable when they present with classic infiltrative growth pattern. However, subset of IDC can occur in a very sneaky way, significantly mimicking the appearance of ductal carcinoma in situ (DCIS). In this condition, it’s much easier to miss the invasive component without pulling ancillary staining when morphologic findings are extremely compatible with DCIS, especially the diagnosis of DCIS was made on the previous biopsy. Here, we reported a 55 year-old female who was noted to have microcalcification at the 11:00 o’clock of the right posterior breast on routine mammographic examination in 09/2023. Biopsy of the calcification area in 10/2023 reported high grade DCIS (ER+ PR-). Histologic examination of subsequent mastectomy specimen showed two separate DCIS-looking areas (Figure 1A-D and Figure 2). Immunohistochemical (IHC) staining showed that myoepithelial markers, smooth muscle myosin heavy chain (SMMHC), p63, CK5/6 and S100, were retained at the periphery of all the expanded acini in one area (Figure 1E-H). Unexpectedly and surprisingly, myoepithelial markers were completely lost at the periphery of part of the DCIS-looking acini in another area (Figure 3A-H), immunohistochemically compatible with the diagnosis of invasive ductal carcinoma admixed with DCIS. Knowing that invasive ductal carcinoma of the breast can present as DCIS-looking morphology, especially given the condition that the diagnosis of DCIS was rendered on the previous biopsy, will enhance awareness of pathologists to recognize DCIS-looking invasive ductal carcinoma. In turn, this will prevent misdiagnosis and under-treatment of patients with invasive ductal carcinoma of the breast.

Recent discoveries of potential ice particles and ice-cemented regolith on celestial bodies like the Moon and Mars have ushered in new opportunities for developing technologies to extract water, facilitating future space missions and activities on these celestial surfaces. This study delves into the potential for water extraction from regolith through an experiment designed to test water recuperation from regolith simulant under varying gravitational conditions. The resultant water vapor extracted from the regolith is re-condensed on a substrate surface and collected in liquid form. Three types of substrates, hydrophobic, hydrophilic, and grooved, are explored. The system’s functionality was assessed during a parabolic flight campaign simulating three distinct gravity levels: microgravity, lunar gravity, and Martian gravity. Our findings reveal that the hydrophobic surface demonstrates the highest efficiency due to drop-wise condensation, and lower gravity levels result in increased water condensation on the substrates. This experiment aims to provide insights into in-situ water recovery, which is pivotal for establishing economically-sustainable water supplies for future missions.

We previously reported nano-pulse treatment (NPT), a pulsed power technology, resulted in 4T1-luc mammary tumor elimination and a strong in situ vaccination, thereby completely protecting tumor-free animals against a second live tumor challenge. The mechanism whereby NPT mounts effective antitumor immune responses in the 4T1 breast cancer predominantly immunosuppressive tumor microenvironment (TME) remains unanswered. In this study, orthotopic 4T1 mouse breast tumors were treated with NPT (100 ns, 50 kV/cm, 1000 pulses, 3 Hz). Blood, spleen, draining lymph nodes and tumors were harvested at 4-hour, 8-hour, 1-, 3-, 7-day. Additional studies were conducted over 3-month posttreatment intervals for the analysis of frequencies, death and functional markers of various immune cells in addition to suppressor function of regulatory T cells (Tregs). NPT was verified to elicit strong in situ vaccination (ISV) against breast cancer and promoted both acute and long-term T cell memory. NPT abolished immunosuppressive dominance systemically and in the TME by substantially reducing Tregs, myeloid-derived suppressor cells (MDSCs), and tumor-associated macrophages (TAMs). NPT induced apoptosis in Tregs and TAMs. It also functionally diminished the Treg suppression capacity, likely explained by the downregulation of activation markers, particularly 4-1BB and TGFβ, and a phenotypic shift from predominantly activated (CD44+CD62L-) to naïve (CD44-CD62L+) Tregs. Importantly, NPT selectively induced apoptosis in activated Tregs and spared effector CD4+ and CD8+ T cells. These changes were followed by a concomitant rise in CD8+CD103+ tissue-resident memory T cells and TAM M1 polarization. These findings indicate that NPT effectively switches the TME and secondary lymphatic systems from an immunosuppressive to an immunostimulatory state allowing cytotoxic T-cell function and immune memory formation to eliminate cancer cells and account for the NPT in situ vaccination.

It’s well known that existing horizontal well drilling and hydraulic fracturing technology that is used to achieve large-scale cost-effective production from immature to low-moderate maturity continental shale in China, where the organic matter mainly exists in the solid form is fairly ineffective. To overcome the obstacles, in-situ conversion technology seems feasible, while implementing it in the target layer along with estimating the amount of expected recoverable hydrocarbon in such shale formations seems difficult. This is because there is no guideline to choose the most appropriate method and select relevant key parameters for this purpose. Hence, based on thermal simulation experiments during the in-situ conversion of crude oil from the Triassic Chang 73 Formation in the Ordos Basin and the Cretaceous Nenjiang Formation in the Songliao Basin, this deficiency in knowledge was addressed. First, relationships between the in-situ converted total organic carbon (TOC) content and the vitrinite reflectance (Ro) of the shales and between the residual oil volume and the hydrocarbon yield was established. Second, the yields of residual oil and in-situ converted hydrocarbon were measured, revealing their sensitivity to fluid pressure and crude oil density. In addition, a model was proposed to estimate the amount of in-situ converted hydrocarbon based on the TOC, hydrocarbon generation potential, Ro, residual oil volume, fluid pressure, and crude oil density. Finally, a method was established to determine key parameters on the final hydrocarbon yield from immature to low-moderate maturity organic material during in-situ conversion in shales. Following the procedure outlined in this paper, estimated recoverable in-situ converted oil in the shales of the Nenjiang Formation in the Songliao Basin was estimated to be approximately 292×108 tons, along with 18.5×1012 cubic meters of natural gas, in an area of approximately 8×104 square kilometers. Collectively, the method developed in this study is independent from the organic matter type and other geological and/or petrophysical properties of the formation and can be applied to other areas globally where there isn’t any available in-situ conversion thermal simulation experimental data.