Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

This study investigates the influence of economic growth on CO2 emissions levels in three developed countries—Argentina, Equatorial Guinea, and South Korea—based on their status as high-income countries. We test the environmental Kuznets curve (EKC) hypothesis using the time series approaches to check the relationship and direction of causality among the variables over a sample spanning 1974–2020. The results show an inverted U-shaped short-run relationship in all three countries. In the long run, only South Korea supports the EKC hypothesis. Further, Granger causality results indicate the existence of causality. These long-run causal relationships between economic growth and emissions recommend one policy implication that wealthy governments must expand investments in renewable clean energy projects and R&D, with regulatory measures to suppress harmful environmental procedures and support environmentally friendly development.

Aiming at the problem of hypersonic morphing vehicle avoiding no-fly zones and reaching the target, an improved predictor-corrector guidance method is proposed. Firstly, the aircraft motion model and the constraint model are established. Then, the basic algorithm is given, the Q-learning method is used to design the attack angle and sweep angle scheme to ensure that the aircraft can fly over the low-altitude zones. The B-spline curve is used to design the location of flight path points and the bank angle scheme is designed according to the predictor-corrector method, so that the aircraft can fly around to avoid high-altitude zones. Next, Monte Carlo reinforcement learning(MCRL) method is used to improve predictor-corrector method and Deep Neural Network(DNN) is used to fit reward function. The improved method can generate trajectory with better performance. Simulation results verify the effectiveness of the proposed algorithm.

Conventional sensors used to measure properties such as deformation or pressure, etc. often make use of metals, ceramics, piezos, and other materials. Many of those materials are very hard, so if they are used as sensors, when the object is deformed, or when the pressure on the object changes from time to time, it is necessary to prepare a variety of sensors with different properties. In this experiment, a dielectric elastomer (DE) pressure sensor was fabricated using a hydrogenated nitrile rubber (HNBR) film with improved hardness and elongation. With this, even very thin film (0.2mm) can be measured at any pressure between 1gf and 20kgf. Previously developed film was harder and less stretchy than the current one, with a pressure detection width from 4 kgf to 120 kgf. This time, however, the pressure sensitivity of the finger has been made more sensitive, making it possible to measure even smaller values. A DE stretch sensor was also developed using single-walled carbon nanotube (SWCNT) electrodes with larger stretchability and flexibility, utilizing this HNBR. This greatly improved the mechanical flexibility and stretchability of the DES. Using this stretch sensor, it became possible to sense the motion of the robot's fingers, and to sense the force (pressure) when the fingertip touched the target object with the DE pressure sensor. In addition, it was confirmed that the sensation of the robot's finger touching an object can be fed back to a human finger by using a small diaphragm type vibrator DE actuator.

Virgin coconut oil (VCO) is a functional food with important health benefits. Its economic interest encourages fraudsters to deliberately adulterate VCO with cheap and low-quality vegetable oils for financial gain, causing health and safety problems for consumers. In this context, there is an urgent need for rapid, accurate and precise analytical techniques to detect VCO adulteration. In this study, the use of Fourier Transform Infrared (FTIR) spectroscopy combined with Multivariate Curve Resolution - Alternating Least Squares (MCR-ALS) methodology was evaluated to verify purity or adulteration of VCO with reference to several low-cost commercial oils such as sun-flower, maize and peanut oils. Control charts were developed to assess the purity of oil samples using MCR-ALS scores values calculated from a data set of pure and adulterated oils. In addition, quantification models were developed using MCR-ALS with correlation constraint for adulterated coconut oil to assess the blend composition. Different data pre-treatment strategies were tested in order to best extract the information contained in the sample fingerprints, and the calibration models were optimised using a genetic algorithm (GA) to select the most important variables. The models gave satisfactory results in external validation procedure, with absolute errors of less than 4.6 % for samples adulterated with sunflower, maize and peanut oils.

In this paper a new approximate procedure is developed for calculating the inclination angle of the end points of statically determinate beams. The method is based on the topology comparison of simple (hinge-roller combination) supported beam and a resemblant cantilever beam. Assuming that the support reactions of the beam are active forces, the virtual displacements at the points of the reaction forces are calculated. Based on these values the inclination angle is calculated. Several examples are considered and the suggested in this paper, while the procedure is applied for various types of structures and loadings. The results, obtained by the suggested numerical procedure, are compared with analytical ones, and they are in good agreement.

The Kummer surface was constructed in 1864. It corresponds to the desingularisation of the quotient of a 4-torus by 16 complex double points. Kummer surface is kwown to play a role in some models of quantum gravity. Following our recent model of the DNA genetic code based on the irreducible characters of the finite group G5:=(240,105)≅Z5⋊2O (with 2O the binary octahedral group), we now find that groups G6:=(288,69)≅Z6⋊2O and G7:=(336,118)≅Z7⋊2O can be used as models of the symmetries in hexamer and heptamer proteins playing a vital role for some biological functions. Groups G6 and G7 are found to involve the Kummer surface in the structure of their character table. An analogy between quantum gravity and DNA/RNA packings is suggested.

This paper is about to estimate the suspended sediment transport amount in the streams flowing into the Sapanca Lake Basin. There are 12 subsidiary streams flowing into the Sapanca Lake Basin. With the aim of estimating the suspended sediment transport in 2012-204 in these subsidiary streams, measurements belonging the parameters such as level, cross sectioning, flow rate, temperature and suspended sediment were made monthly. Along the measurement period, weather conditions were above seasonal normal and precipitations decreased. In order to estimate the suspended sediment amount by using results of the measurement obtained, Artificial Neuron Network (ANN), Sediment Rating Curve (SRC) and Multiple Linear Regression (MLR) models were used for different scenarios. It was seen that artificial neuron networks yielded the most accurate results among the models.

There are several challenges on how to attain energy efficiency while maintaining balance among factors affecting energy consumption such as power rating and temperature setpoints of cooling units, room temperature and humidity, and indoor air quality (IAQ). A real-time energy and IAQ monitoring system were installed in an educational building to profile the operational power consumption of inverter-based air condition unit (ACU) installed in each room. Polynomial curve and neural fitting regression analysis were applied to the real-time power consumption, indoor temperature and humidity, and carbon dioxide (CO2) level data. The derived models were able to provide the stabilizing indoor thermal and air conditions of the room to reach steady state ACU power consumption. These collected data and calculated parameters can be used to define rules in automating control of cooling appliances for an efficient energy utilization. The regression approaches, using real-time data, have determined the influence of indoor heat conditions and carbon dioxide levels on ACU power consumption. These parameters were utilized to establish consistent values for temperature, humidity, and carbon dioxide levels under stable settings of inverter-based air conditioning units.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

Recent satellite measurements of glacier mass balance show mountain glaciers all over the world had generally negative mass balances in the first decades of the 21st century. Mean summer temperatures all over the world rose from 1961-90 to 1991-2020, implying increasingly negative mass balances. We study archived annual balances for 38 Northern Hemisphere glaciers to assess changes within in the 19612020 period. We use a modified doublemass curve to visualize mass balance changes occurring around 1990. Mean balances 196190 were already small negative for many of the studied glaciers and became even more negative in 19912020 for glaciers in the Alps, at high latitudes and in western North America. The largest mass balance changes are for some glaciers in the Alps. We are unable to explain the lack of change in mean balance for one glacier in High Mountain Asia. We find complex changes for eight glaciers in Scandinavia, even including one glacier with positive balance. We explain these changes by visualizing deviations of winter and summer balances from their respective 1961-90 mean values. High winter balances in the 1990s for Scandinavia partly obscured the emerging trend of increasingly negative summer balances, which we expect to continue in the future.

Automation of forest field reference data collection has been an intensive research objective for laser scanning scientists ever since the invention of terrestrial laser scanning more than two decades ago. Recently, it has been proposed that such automated data collection providing both the tree heights and stem curves would require a combination of above-canopy UAV point clouds and terrestrial point clouds. In this study, we demonstrate that an under-canopy UAV laser scanning system utilizing a rotating laser scanner can alone provide accurate estimates of the canopy height and the stem volume for the majority of the trees in a boreal forest. To this end, we mounted a rotating laser scanner based on a Velodyne VLP-16 sensor onboard a manually piloted UAV. The UAV was commanded with the help of a live video feed from the onboard camera of the UAV. Since the system was based on a rotating laser scanner providing varying view angles, all important elements such as treetops, branches, trunks, and ground could be recorded with laser hits. In an experiment including two different forest structures, namely sparse and obstructed canopy, we showed that our system can measure the heights of individual trees with a bias of -20 cm and a standard error of 40 cm in the sparse forest and with a bias of -65 cm and a standard error of 1 m in the obstructed forest. The accuracy of the obtained tree height estimates was equivalent to airborne above-canopy UAV surveys conducted in similar forest conditions. The higher underestimation and higher inaccuracy in the obstructed site can be attributed to three trees with a height exceeding 25 m and the applied laser scanning system VLP-16 that had a limited height measurement capacity when it comes to trees taller than 25 m. Additionally, we used our system to estimate the stem volumes of individual trees with a standard error at the level of 10%. This level of error is equivalent to the error obtained when merging above-canopy UAV laser scanner data with terrestrial point cloud data. Future research is needed for testing new sensors, for implementing autonomous operation inside canopies through collision avoidance and navigation through canopies, and for developing robust methods that work also with more complex forest structure. The results show that we do not necessarily need a combination of terrestrial point clouds and point clouds collected using above-canopy UAV systems in order to accurately estimate the heights and the volumes of individual trees.

Bioelectrocatalysis provides the intrinsic catalytic-functions of redox enzymes to non-specific electrode reactions and is the most important and basic concept for biosensors. This review starts by describing fundamental characteristics of bioelectrocatalytic reactions in mediated and direct electron transfer types from a theoretical viewpoint and summarizes amperometric biosensors based on multi-enzymatic cascades and for multi-analyte detection. The review also introduces prospective aspects of two new concepts of biosensors: mass-transfer-controlled (pseudo)steady-state amperometry at microelectrodes with enhanced enzymatic activity without calibration curves and potentiometric coulometry at enzyme/mediator-immobilized biosensors for absolute determination.

Microbial growth has been of prime importance to the researchers in health and biotechnology industries. It has been known to be closely associated to the secretion of extracellular polymeric substances that help in the formation of colonies. Inter-microbial communication happens within such colonies by means of extracellular electron transfer mediated by the aforementioned polymeric substances. Conventionally, different phases of microbial growth are monitored with the aid of a traditional UV-Visible spectrophotometer by measuring the optical density of the liquid medium at 280 nm. In this paper, we have developed an alternative novel way to sense different growth phases employing electrochemical means i.e. two-terminal cyclic voltammetry. This cyclic voltammetry relies on the extracellular electron transfer mechanism taking place via the polymeric substances secreted by the microorganisms, measured by the temporal area changes in the current-voltage hysteresis curves in the inoculated nutrient broth. This work paves a new way to detect the biological activity in the medium, which can be directly correlated to the population of microorganisms. It would be of immense interest to scientists and researchers working in the field of microbiology as well as in development of biosensors, electrochemical sensors etc. which would be helpful in absence of traditional spectrophotometers.

Although work events can be regarded as pivotal elements of organizational life, only a few studies have examined how positive and negative events relate to and combine to affect work engagement over time. Theory suggests that to better understand how current events affect work engagement (WE), we have to account for recent events that have preceded these current events. We present competing theoretical views on how recent and current work events may affect employees (e.g., getting used to a high frequency of negative events or becoming more sensitive to negative events). Although the occurrence of events implies discrete changes in the experience of work, prior research has not considered whether work events actually accumulate to sustained mid-term changes in WE. To address these gaps in the literature, we conducted a week-level longitudinal study across a period of 15 consecutive weeks among 135 employees, which yielded 849 weekly observations. While positive events were associated with higher levels of WE within the same week, negative events were not. Our results support neither satiation nor sensitization processes. However, high frequencies of negative events in the preceding week amplified the beneficial effects of positive events on WE in the current week. Growth curve analyses show that the benefits of positive events accumulate to sustain high levels of WE. WE dissipates in the absence of continuous experience of positive events. Our study adds a temporal component and informs research that has taken a feature-oriented perspective on the dynamic interplay of job demands and resources.

Inequality of health service for different specialty categories not only occurs in different areas inequality of health service for different specialty categories in the world, but also happens in the online service platform. In the online health community (OHC), health service was often of inequality for different specialty categories, including both online views and medical consultation for offline registered service. Moreover, how the factor city-level impacts the inequality of health service in OHC is still unknown. We designed a causal inference study with data on distributions of serviced patients and online views in over 100 distinct specialty categories on one largest OHC in China. To derive the causal effect of the city-levels (two levels inducing 1 and 0) on the Gini coefficient, we matched the focus cases in cities of rich healthcare resources with the potential control cities. For the Gini coefficient of serviced patients in over 100 specialty categories, the average treatment effect of level-1 cities is 0.470, which is 0.029 higher than that of the matched group. Similarly, for the Gini coefficient of online views, the average treatment effect of Level-1 cities is 0.573, which is 0.016 higher than that of the matched group. For each of the specialty categories, we also estimated the average treatment effect the specialty category’s Gini coefficient ( ) with the balanced covariates. The results support the argument that the total Gini coefficient of all the doctors in OHC shows that the inequality of health service is still very serious. This study contributes to the development of the theoretically grounded understanding of the causal effect of city-level on the inequality of health service in an online to offline healthcare service setting.

The aim of this work is to introduce new ways to model the I-V characteristic of a PV cell or PV module using straight lines and Bézier curves. This is a complete novel approach, Bézier curves being previously used mainly for computer graphics. The I-V characteristic is divided in three sections, modeled with lines and a quadratic Bézier curve in the first case and with three cubic Bézier curves in the second case. The result proves to be accurate and relies on the fundamental points usually present in the PV cell datasheets: Voc (the open circuit voltage), Isc (the short circuit current), Vmp (the maximum power corresponding voltage) and Imp (the maximum power corresponding current) and the parasitic resistances Rsh0 (shunt resistance at Isc) and Rs0 (series resistance at Voc). The proposed algorithm completely defines all the implied control points and the error is analyzed. The temperature and irradiance influence is also analyzed. The model is also compared using the least squares fitting method. The final validation shows how to use Bézier cubic curves to accurately represent the I-V curves of an extensive range of PV cells and arrays.

This longitudinal study examined the development of executive function and calibration accuracy in pre-adolescents. Two hundred sixty two students(127 females) from grades 4 (n = 91), 5 (n = 89) and 6 (n = 82) took measures of executive function and performance calibration in a sport task, three times within a period of 20 months. A latent growth curve modeling analysis showed a significant relation between the rates of change of executive function and calibration. Further, the results showed a dynamic interplay in the development of executive function and calibration. There were significant inter-individual differences in the estimated population means both in executive function and calibration and in the rate of change of executive function, but not in the rate of change for calibration. The age of the participants had a positive effect only on the estimated population mean of executive function.

Background: The purpose of this study was to compare the immediate and long-term complications that are associated with the utilized techniques for the insertion of indwelling central venous catheters, that is the open surgical technique, the ultrasound-guided technique and the transcutaneous technique based on external anatomical landmarks in the right internal jugular vein, to a pediatric population. Methods: This was a prospective randomized trial based on a pediatric patient population, under 16 years of age, of a tertiary pediatric-oncological hospital. Procedure was performed by a medical team with varying experience regarding the percutaneous and open insertion methods. We studied the outcome of our procedure, based on the immediate and delayed complication rate, as well as the needed time in order to complete the procedure and mean duration of line use. Results: The patients that were inserted in our protocol were divided into three subgroups, based on the selected technique for the insertion of the central venous catheter. A total number of 88 insertions (25.4%) (out of 346) were based on the technique that was using external anatomical landmarks, 121 insertions were based on the ultrasound-guided transcutaneous technique (34,9%), whereas in 137 cases (39.5%) the open surgical technique was preferred. All cases that were related to catheter re-insertion were excluded from our study. We performed a statistical analysis regarding the catheter dwell time between the three subgroups of patients and no significant difference was recorded. Moreover, the development of thrombosis was investigated, and we mentioned that the higher percentage of this complication was related with the transcutaneous external landmark and open surgical technique. Also, the incidence of infection was taken into consideration, which manifested an increased incidence when the transcutaneous technique based on external landmarks was used. Conclusions: Ultrasound guided percutaneous insertion was considered to be a safe and effective technique for the insertion of central venous catheters. Our study also demonstrated a decrease in operating times, when performed by operators with increasing expertise, increased preservation of the diameter of the venous lumen, and no increase in complication rates when the ultrasound-guided technique was selected.

This paper presents a V2G strategy to flatten the daily load curve by considering the charging and discharging location of the electric vehicle to help understand the effect of the load generated by charging and discharging of the electric vehicle on the power grid. Based on the estimated share of electric vehicles, the assumption that electric vehicles go to work in the morning and leave in the afternoon was set, and the electric vehicle discharge power was calculated by reflecting both the characteristics of vehicles that go to work in the morning and the SMP1 and SMP2 plans. In addition, the electric vehicle charging power was calculated by reflecting the characteristics of vehicles returning home from work in the afternoon and the TOU rate system. In other words, in order to establish an efficient V2G strategy, a charging/discharging type-specific modeling was developed that considered all the characteristics of an electric vehicle commuting vehicle, and charging and discharging daily load using SMP1 and SMP2 rate plans for morning discharge and TOU1 and TOU2 rate plans for afternoon charging were applied. After calculating the curve, this value was compared and analyzed to evaluate the effect on grid leveling by adding the existing load. The analysis provides an accurate understanding of the impact of EV charging and discharging loads on the power grid according to V2G strategies. In this paper, it is helpful to apply EV charge and discharge management technology to avoid grid overload and minimize grid expansion by leveling the grid daily load curve by applying appropriate SMP and TOU rates through the establishment of an efficient V2G strategy by charge and discharge modeling.

Keywords: Hypertensive emergency; diagnosis; lactate dehydrogenase; high sensitivity cardiac troponin T; brain natriuretic peptide; area under the curve.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

The seismic damage in reinforced concrete bridges is identified in this study using the "M and P" hybrid technique initially developed for planar frames. The proposed methodology involves a series of pushover and instantaneous modal analyses with a progressively increasing target deck displacement along the longitudinal direction of the bridge. From the results of these analyses, the diagram of the instantaneous eigenfrequency of the bridge, ranging from the health state to near collapse, is plotted against the inelastic seismic deck displacement. By pre-determining the eigen-frequency of an existing bridge along its longitudinal direction through "monitoring and frequency identification", the target deck displacement corresponding to the damage state can directly be found from this diagram. Subsequently, the damage can be identified by examining the results of the pushover analysis at the step where the target deck displacement is indicated. The effectiveness of this proposed technique is evaluated in the context of multiple span bridges with unequal pier heights, illustrated through an example of a four-span bridge. The findings demonstrate that the damage potential in bridge piers can be successfully identified by combining the results of a monitoring process and pushover analysis.

Currently, many researchers have an interest in the investigation of the electric field in the fair-weather electric environment, along with its diurnal and seasonal variations across all regions of the world. However, a similar study in the southern part of Siberia has not yet been carried out. In this regard, the study aims to estimate the mean values of the electric field and their variations in the mountain and steppe landscapes using measurement data from the Khakass-Tyva expedition in 2022. The maximum values of positive ion density were noted at the site in the Iyussko-Shirinsky steppe between Belyo and Tus salt lakes in the Khakass-Minusinsk ba-sin. The maximum values of negative ion density were observed at site in the Shol tract in the center part of the Tyva depression. The potential gradient tends to increase with altitude and reaches a maximum in the highlands. The maximum values of the potential gradient were noted in the highlands plateau near the Mongun-Taiga mountain massif and Khindiktig-Khol lake. The diurnal cycles of potential gradient at different observation sites were divided into two groups: 1) a diurnal cycle in the form of a double wave; 2) a daily cycle with a more complex course due to the strong influence of local factors.

Plant N concentration (PNC) has been commonly used to guide farmers in assessing maize (Zea mays L.) N status and making in-season N fertilization decisions. However, PNC varies based on the development stage and therefore a relationship between biomass and N concentration is needed (i.e., critical N dilution curves; CNDC) to better understand when plants are N deficient. A few CNDC have been developed and used for plant N status diagnoses, but have not been tested in the US Midwest. The objective of this study was to evaluate under highly diverse soil and weather conditions in the US Midwest the performance of CNDCs developed in France and China for assessing maize N status. Maize N rate response trials were conducted across eight US Midwest states over three years. This analysis utilized plant and soil measurements at V9 and VT development stages and final grain yield. Results showed that the French CNDC (y=34.0x-0.37, where y is critical PNC, x is aboveground biomass) was better with a 91% N status classification accuracy compared to only 62% with the Chinese CNDC (y=36.5x-0.48). The N nutrition index (NNI), which is the quotient of the measured PNC and the calculated critical N concentration (Nc), based on the French CNDC was significantly related to soil nitrate-N content (R2=0.38-0.56). Relative grain yield on average reached a plateau at NNI values of 1.36 at V9 and 1.21 at VT, but for individual sites ranged from 0.80 to 1.41 at V9 and from 0.62 to 1.75 at VT. The NNI threshold values or ranges optimal for crop biomass production may not be optimal for grain yield production. It is concluded that the CNDC developed in France is suitable as a general diagnostic tool for assessing maize N status in US Midwest. However, the threshold values of NNI for diagnosing maize N status and guiding N applications vary significantly across the region, making it challenging for guiding specific on-farm N management. More studies are needed to determine how to effectively use CNDC to make in-season N recommendations in the US Midwest.

Due to the increase in the emission of greenhouse gases, the hydrologic cycle is being altered on the daily basis. This has affected the variations in relations of intensity, duration, and frequency of rainfall events. Intensity Duration Frequency (IDF) curves describe the relationship between rainfall intensity, rainfall duration and return period. IDF curves are one of the most often applied implements in water resource engineering, in areas such as for operating, planning and designing of water resource projects, or for numerous engineering projects aimed at controlling floods. In particular, IDF curves for precipitation answer problems of improper drainage systems or conditions and extreme characters of precipitation which are the main cause of floods in Nyabugogo catchment. This study aims to establish Rainfall IDF empirical equations, curves and hydrological discharge (predicted peak rate of runoff (Qlogy)) equations for eight Districts that will be used for designing an appropriate and sustainable hydraulic structures for controlling flood to reduce potential loss of human and aquatic life, degradation of water, air and soil quality and property damage and economic lessen caused by flood in Nyabugogo catchment. However Goodness of Fit tests revealed that Gumbel’s Extreme-Value Distribution method appears to have the most appropriate fit compared with Pearson type III distribution for validating the Intensity-Duration-Frequency curves and equations through the use of daily annual for each meteorological station. The findings of the study show that the intensity of rainfall increases with a decrease in rainfall duration. Additionally, a rainfall of every known duration will have a higher intensity if its return period is high, while the predicted peak rate of runoff (Qlogy) increases also with an increase in the intensity of rainfall.

Sediment transport is highly sensitive to flow conditions, showing significant increase during flood events. Based on this principle, this study set out to rank flood events occurring along river Trotuș (Romania) based on the amount of transported sediment and event duration. The 77 flood events recorded from 2000 to 2017 were ranked into 4 classes: type A (4%); type B (16%), type C (14%) and type D (66%). The sediment transport specific for the 4 types of flood events was related to the flow discharge (sediment rating curve and hysteresis effect), the specific stream power and the energy expenditure of these events. More than 60% of the hysteresis loops typical for flood events were clockwise, thus singling out the channel as the main sediment source. Ca. 74% of the total sediment yield was transported at stream power values higher than the 300 Wm-2 threshold, which was exceeded in less than 1% of the investigated timeframe. The changes occurring in the sediment transport rates after major floods show that these events are significant thresholds in the hydrogeomorphic evolution of river channels.

In India, particularly within its North-Eastern territories, the occurrence of landslides triggered by post-dry period rainfall events is a significant concern, with the phenomena persistently causing extensive damage to both life and infrastructure. Despite the inevitability of such natural disasters, it is understood that the impact they exert can be substantially mitigated through the implementation of pre-emptive measures. Critical to the endeavour of landslide prevention is the application of a spectrum of mitigation strategies, predicated upon a foundational analysis of slope stability to ascertain critical surfaces for intervention. This investigation delves into the dynamics of partially saturated soils, a condition commonly resultant from the prolonged dry periods preceding the monsoonal rains. The study's focal point is an experimental examination conducted on soil samples to assess parameters such as soil matric suction and unconfined compressive strength across varying degrees of saturation and density, alongside performing analyses of slope failure incidents after dry period during the 2017 monsoon in the Lunglei district, Mizoram based on some established data. The Soil-Water Characteristic Curve (SWCC), derived from soil suction measurements employing the ASTM D5298-10 standard, utilizes a contact filter paper method and serves to delineate the moisture transition phases of the slope. To replicate the desiccation of the soil slope after monsoonal rains, a microwave drying technique based on the ASTM standard was employed to prepare unsaturated soil samples for Unconfined Compressive Strength (UCS) testing. The integrity of the slope was evaluated in a temporal context, before and after rainfall events of varied intensities throughout the calendar year, utilizing a blend of numerical modeling and empirical laboratory investigations. The persistence of real onsite slope failures underscores the necessity for a numerical analysis approach to unravel the underlying factors causing slope instability, especially given the absence of prior stability assessments for the landslide in question. An evaluation of SWCC curves, UCS tests on partially saturated soil at different densities and saturation and the utilization of the benchmark data collected in 2017 on the shallow transitional landslide in Lunglei, Mizoram caused by intense monsoonal precipitation, are central key data and information used to carry out this research. Rainfall data for Lunglei, sourced from the Mizoram Meteorological Department, facilitated a real-time monsoonal data-driven numerical analysis. This analysis elucidated the pivotal role of rainfall in inducing slope failure, indicating a marked destabilization of the slope after precipitation events. The implications of these findings are far-reaching, suggesting a foundational basis for the development of an advanced landslide early warning system, thereby enhancing disaster preparedness, and mitigating potential damages.

Elliptic curve cryptography (ECC) over prime fields relies on scalar point multiplication realized by point addition and point doubling. Point addition and point doubling operations consist of many modular multiplications of large operands (256 bits for example), especially in projective and Jacobian coordinates which eliminate the modular inversion required in affine coordinates for every point addition or point doubling operation. Accelerating modular multiplication is therefore important for high-performance ECC. This paper presents the hardware implementations of modular multiplication algorithms, including 1) Interleaved modular multiplication (IMM), 2) Montgomery modular multiplication (MMM), 3) Shift-sub modular multiplication (SSMM), 4) SSMM with advance preparation (SSMMPRE), and 5) SSMM with CSAs and sign detection (SSMMCSA) algorithms, and evaluates their execution time (the number of clock cycles and clock frequency) and required hardware resources (ALMs and registers). Experimental results show that SSMM is 1.76 times faster than IMM, and SSMMCSA is 3.21 times faster than IMM. We also present the ECC hardware implementations based on the Secp256k1 protocol in affine, projective, and Jacobian coordinates using the IMM, SSMM, SSMMPRE, and SSMMCSA algorithms, and investigate their cost and performance. Our ECC implementations can be applied to the design of hardware security module systems.

The purpose of this research was to analyze the moderating effect of clean energy innovation on the relationship between corporate carbon footprint and corporate profits in those industrial sectors associated with high demand for fossil fuels in which it is "hard to abate" CO₂e emissions. It used a longitudinal research design, in particular a panel study under a structural equation modeling (SEM) approach, based on partial least squares. For the longitudinal moderation analysis, this research employed the Bayesian method by defining a multiple-indicator latent growth curve model (B-LGC model). A global sample was used consisting of 7,827 firm-year observations between 2015 and 2021 corresponding to 167 international firms. The results revealed a very significant impact of the corporate carbon footprint on corporate profits. Likewise, the results showed that innovations in clean energy, when measured as the consumption of renewable energy, positively moderates the relationship between the greenhouse gas emissions from the value chain associated with Scope 3 of the Greenhouse Gas (GHG) Protocol, and the gross profit margin obtained. Besides the academic contribution represented by the moderating effect of clean energy innovation, these findings imply that a more detailed understanding of the emissions of the entire value chain (Scope 3 CO₂e) by executives and managers of high emitting CO₂e companies represents an effective mechanism to obtain higher profits, create competitive advantages and, at the same time, achieve a net zero emissions strategy. More importantly, public policy makers will be able to use these results to revise CO₂e-related policies paying more attention to the Scope 3 CO₂e emissions produced by these companies, to formulate regulatory and control mechanisms that stimulate clean energy innovation.

The requirements for efficient replacement of fossil fuel, combined with the growing energy crisis, put hydrogen production into focus. Efficient and cost-effective electrocatalysts are needed for H2 production, and novel strategies for their discovery must be developed. Here we utilized Kinetic Monte Carlo (KMC) simulations to demonstrate that hydrogen evolution reaction (HER) can be boosted via hydrogen spillover to the support when the catalyst surface is largely covered by adsorbed hydrogen under operating conditions. Based on the insights from KMC, we synthesized a series of reduced graphene oxide-supported catalysts and compared their activities towards HER in alkaline media with that of corresponding pure metals. For Ag, Au, and Zn, the support effect is negative, but for Pt, Pd, Fe, Co, and Ni, the presence of the support enhances HER activity. The HER volcano, constructed using calculated hydrogen binding energies and measured HER activities, shows a positive shift of the strong binding branch. This work demonstrates the possibilities of metal|support interface engineering for producing effective HER catalysts and provides general guidelines for choosing novel catalyst-support combinations for electrocatalytic hydrogen production.

This paper gives a new unified formula for the Newtonian fluids valid for all pipe flow regimes from laminar to the fully rough turbulent. It includes laminar, unstable sharp jump from laminar to turbulent, and all types of the turbulent regimes: smooth turbulent regime, partial non-fully developed turbulent and fully developed rough turbulent regime. The formula follows the inflectional form of curves as suggested in Nikuradse’s experiment rather than monotonic shape proposed by Colebrook and White. The composition of the proposed unified formula consists of switching functions and of the interchangeable formulas for laminar, smooth turbulent and fully rough turbulent flow. The proposed switching functions provide a smooth and a computationally cheap transition among hydraulic regimes. Thus, the here presented formulation represents a coherent hydraulic model suitable for engineering use. The model is compared to existing literature models, and shows smooth and computationally cheap transitions among hydraulic regimes.

The new observations, including the fastest star, the circular velocity curve of the Milky Way and the fast galaxy bar, should imply that the mass of the center of the Milky Way is almost 10¹¹ times the mass of the Sun.

In this paper a protection scheme is provided to protect microgrid by considering the problems that are generated by addition of distributed generators to distribution networks and change these networks from passive to active. At first, changes in microgrid conditions that can affect short-circuit current is explained. Then Based on these changes, an algorithm is proposed to update relays settings. The algorithm can be used for both instantaneous and inverse time relays. In this protection scheme, central unit has no place and relays are responsible for monitoring microgrid and update their settings. In other words, this protection scheme is an adaptive and decentralized microgrid protection scheme. Instantaneous overcurrent relays are used in this paper. To avoid storing large amounts of setting data in relays memory, a method for calculating pickup current of instantaneous relay is provided. Since digital relays used, a new characteristic curve for instantaneous relay for better performance in the field of backup protection is defined. This new characteristic curve has two peakup currents: one of them for main protection and the other one for backup protection. Then coordination of instantaneous relay using the new characteristic curve is explained. At the end, this protection scheme is implemented on a microgrid.

Crash prediction of the sharp horizontal curve segment (SHCS) of a freeway is an important tool in analyzing safety of SHCSs and in building a crash prediction model (CPM). The design and crash report data of 88 SHCSs from different institutions were surveyed and three negative binomial (NB) regression models and three generalized negative binomial (GNB) regression models were built to prove that the interactive influence of explanatory variables plays an important role in fitting goodness. The study demonstrates the effective use of the GNB model in analyzing the interactive influence of explanatory variables and in predicting freeway basic segments. Traffic volume, highway horizontal radius, and curve length have been formulated as explanatory variables. Subsequently, we performed statistical analysis to determine the model parameters and conducted sensitivity analysis. Among the six models, the result of model 6, which considered interactive influence, is much better than those of the other models by fitting rules. We also compared the actual results from crashes of 88 SHCSs with those predicted by models 1, 3, and 6. Results demonstrate that model 6 is much more reasonable than models 1 and 3.

In this paper we review dynamics and roughness of bonds in proteins on example of albumin, that is important from the physiological point of view. We have performed computer simulations of albumin chain. Statistics were collected by performing many simulations realizations for each experimental setting. We concentrate on hydrogen bonds, cation-π and π- π interactions and NP contacts. Histograms of hydrogen bonds length are positively skewed in contrary to histograms of interactions and HP contacts that are negatively skewed. Scaling exponents of power spectra of energies of bonds / interactions /contacts are in range -0.2 to -0.5 and significantly differ between various hydrogen bonds or interactions. Varying scaling of such spectra can be used to classify between distinct bonds or contacts. Concerning particular amino-acids, largest amount of HBO H20 bonds are between Glutamate (GLU) amino-acids and water particle, while large amount of HBO bonds are formed with Lysine (LYS). For HP contacts the mayor role plays Phenylalanine (PHE) and Leucine (LEU) amino-acids. From decay curves HBO H2O bonds decays in fastest rate, while HBO bonds and HP contacts at slowest rate. We present as well decay curves of bonds formed by particular amino-acids, that gives interesting results.

Static standing postural stability has been measured by multiscale entropy (MSE), which is used to measure complexity. In this study, we used the average entropy (AE) to measure the static standing postural stability, as AE is a good measure of disorder. The center of pressure (COP) trajectories were collected from 11 subjects under four kinds of balance situation, from stable to unstable: bipedal with open eyes, bipedal with closed eyes, unipedal with open eyes, and unipedal with closed eyes. The AE, entropy of entropy (EoE), and MSE methods were used to analyze these COP data, and EoE was found to be a good measure of complexity. The AE of the 11 subjects sequentially increased by 100%as the balance situations progressed from stable to unstable, but the results of EoE and MSE did not follow this trend. Therefore, AE, rather than EoE or MSE, is a good measure of static standing postural stability. Furthermore, the comparison of EoE and AE plots exhibited an inverted U curve, which is another example of a complexity versus disorder inverted U curve.

The study comprehensively evaluated the prognostic roles of PLR, NLR, MLR, BLR, and ELR in patients with acute exacerbation chronic obstructive pulmonary disease (AECOPD). 619 patients with AECOPD and 300 healthy volunteers were retrospectively included into the study. The clinical characteristics containing laboratory findings of the AECOPD patients and the blood cell counts (CBCs) of the healthy volunteers were collected. Compared with the healthy volunteers, PLR, NLR, and MLR were elevated in COPD patients in stable condition, and were further ele-vated during exacerbation. ELR showed the opposite trend. PLR, NLR, and MLR were all posi-tively correlated with hospital LOS as well as CRP. In contrast, ELR was negatively correlated with hospital LOS as well as CRP. Elevated PLR, NLR, and MLR were all associated with more serious airflow limitation in AECOPD. Elevated PLR, NLR, and MLR were all associated with increased in-hospital mortality while Elevated ELR was associated with decreased in-hospital mortality in AECOPD. A nomogram was construct to predict in-hospital mortality in AECOPD. The nomo-gram had a C-index of 0.850 (95% CI: 0.799 – 0.901) with good predictive value and clinical ap-plicability. In summary, PLR, NLR, MLR, and ELR served as predictors for clinical outcomes in patients with AECOPD.

The effectiveness of a recently proposed methodology in the identification of damage in planar, multi-storey, Reinforced Concrete (RC) moment-frames, which develop a plastic-yield mechanism on their beams, is showcased here via the examining of a group of such existing multi-storey frames with three or more unequal spans. According to the methodology, the diagram of the instantaneous Eigen-Frequencies of the frame in the nonlinear regime is drawn as a function of the inelastic seismic roof displacement by performing a sequence of pushover and instantaneous modal analyses with gradually increasing target displacement. Using this key-diagram, the locations of severe seismic damage in an existing moment-frame can be evaluated if the instantaneous fundamental eigen-frequency of the damaged frame, at an analysis step within the nonlinear area, is known in advance by “the monitoring and the identification of frequencies” using a local network of uniaxial accelerometers. This is a hybrid technique because both procedures, the instrumental Monitoring of the structure and the Pushover analysis on the frame (M and P technique), are combined. Moreover, the damage image of the planar multi-storey moment-frame is illustrated, and the lateral stiffness matrix of the damaged frame is calculated with high accuracy.

The intention of this paper is to point out a remarkable hitherto unknown effect of General Relativity. Starting from fundamental physical principles and phenomena arising from General Relativity, it is demonstrated by a simple Gedankenexperiment that a gravitational lens enhances not only the light intensity of a background object but also its gravitational field strength by the same factor. Thus, multiple images generated by a gravitational lens are not just optical illusions, they also have a gravitational effect at the location of the observer! The "Gravitationally Lensed Gravitation" (GLG) may help to better understand the rotation curves of galaxies since it leads to an enhancement of the gravitational interactions of the stars. Furthermore, it is revealed that besides a redshift of the light of far distant objects, the cosmic expansion also causes a corresponding weakening of their gravitational effects. The explanations are presented entirely without metric representation and tensor formalism. Instead, the behavior of light is used to indicate the effect of spacetime curvature. The gravitation is described by the field strength which is identical to the free fall acceleration. The new results thus obtained provide a reference for future numerical calculations based on the Einstein field equations.

This article is devoted to the problem of genetically coding of inherited cyclic structures in biological bodies, whose life activity is based on a great inherited set of mutually coordinated cyclic processes. The author puts forward and arguments the idea that the genetic coding system is capable of encoding inherited cyclic processes because it itself is a system of cyclic codes connected with Boolean algebra of logic. In other words, the physiological processes in question are cyclical because they are genetically encoded by cyclic codes. In support of this idea, the author presents a set of his results on the connection of the genetic coding system with cyclic Gray codes, which are one of many known types of cyclic codes. This opens up the possibility of using for modeling inherited cyclic biostructures those algebraic and logical theories and constructions that are associated with Gray codes and have long been used in engineering technologies: Karnaugh maps, Hilbert curve, Hadamard matrices, Walsh functions, dyadic analysis, etc. Additionally, the connections of these constructions with statistical rules of genomic DNAs and binary-genomic numbers are considered.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land are a major cause of increasing atmospheric pCO2. Our modelling analysis of reactions by dissolved inorganic carbon shows that increasing atmospheric CO2 could be caused thermodynamically by falling land surface pH values. This hypothesis challenges the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels. Strong acids generated by oxygen from reduced nitrogen and sulphur emits CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils from pH 6.5 to above 8. Each general decrease of aqueous pH value of 0.01 units from acidification of surface water potentially increases the pCO2 in the atmosphere by about 7 ppmv. Contrary to prevailing assumptions that CO2 emissions from combusting fossil fuels can remain in the atmosphere for more than a millennium, such emissions may be partly nullified by global greening from enhanced rates of photosynthesis as well as oceanic absorption. The surface pH value of the ocean has been shown to decrease as atmospheric pCO2 rises. Therefore, our qualitative estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. To the extent that significant acidification of the land is occurring, through export of alkaline produce, the use of artificial nitrogen fertilisation and possible other causes, the prevailing methods of reducing CO2 emissions will fail. However, these acidifying processes on land have not been considered by previous biogeochemical reviews. Despite counter measures, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address such a major cause. This hypothesis can be tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions described in this article with those when corrective counter measures are applied.

Posttraumatic stress disorder (PTSD) and/or specific PTSD symptoms may evoke disordered eating and unhealthy lifestyles, resulting in adverse cardiometabolic events (e.g., hypertension and obesity) in certain groups, which may implicate the treatment of this complex condition. The diagnostic criteria of PTSD have lately expanded beyond the three common symptoms (intrusion, avoidance, and hyperarousal). Simultaneously, four-, five-, and six-dimensional structures of the Impact of Event Scale-Revised (IES-R), a popular PTSD measure, seem to be more robust than the original three-dimension structure. Within the context of COVID-19, this instrumental study used a convenience sample of 58 dental healthcare workers (HCWs) from Russia (mean age = 44.1±12.2 years, 82.8% females) to examine the criterion and predictive validity of two IES-R structures: the IES-R3 and the IES-R6 (with the added symptoms of numbing, sleep disturbance, and irritability). The subscales of the two IES-R structures expressed good internal consistency, strong correlations with the PTSD Symptom Scale (PSS), hypertension diagnosis, and high body mass index (BMI). In receiver-operating characteristic (ROC) curve analysis, all IES-R models perfectly predicted the PSS (all area under the curve (AUC) >0.9, p values <0.001). The IES-R, both hyperarousal subscales, and the IES-R3 intrusion subscale significantly predicted high BMI. Both avoidance subscales and the IES-R3 intrusion subscale, not the IES-R, significantly predicted hypertension. In conclusion, both IES-R structures can reliably measure PTSD symptoms. The IES-R, hyperarousal, and intrusion may be credible criterion variables for predicting high BMI within PTSD while the intrusion and avoidance subscales may reflect the cardiovascular consequences associated with PTSD more reliably than the IES-R itself. The IES-R subscales may predict cardiometabolic adversities in PTSD, signifying a need for proper assessment of lifestyle and the application of dietary and exercise interventions in order to lower physical morbidity in PTSD. Replicating the study in larger samples, which comprise different physical and mental conditions from heterogenous cultural contexts is pivotal to validate the results (e.g., in specific groups such as those with confirmed traumatic exposure and comorbid mood dysfunction).

The transport and entanglement of photons is becoming prominent in optics applied to information and quantum computing, where the angular momentum of light stands out in the exchange and inversion of quantized states, with prospects for several technological applications, such as the transport and storage of quantum information. In order to contribute to the understanding of quantized states in photon-matter interaction, we describe a quantized state equation in multidimensional Hilbert space for the diagnosis of OAM states, where probabilities arise in a relativistic setting. It was found that the classical-relativistic variability of the probabilities constitutes a resultant capable of describing the quantized states of light, where the state variable is the variation of the angular momentum of the photon, capable of estimating the orbital angular momentum inversion points at angular incidence. It was found that the chances of finding the quantized states of light at angular incidence can be treated by purely relativistic probabilities, explaining that when both states have equal chances of being found and the angular momentum variation is zero, the source-observer synchronizations occur at the step of increasing relativistic regime of the photon dynamics. We found that the relativistic effect from the perspective of the source referential is able to alter the chances of an event occurring, dilating and contracting the probabilities of finding a quantized state of light at angular incidence.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.