Herein, we have fabricated graphitic carbon nitride (g-C3N4) nanosheets with embedded ZnCdS nanoparticles to form a type II heterojunction using a facile synthesis approach and used for photocatalytic H2 production. The morphologies, chemical structure and optical properties of the obtained g-C3N4‒ZnCdS samples were characterized by a battery of techniques such as, TEM, XRD, XPS and UV-Vis DRS. The as-synthesized g-C3N4‒ZnCdS, photocatalyst exhibits the highest hydrogen production rate of 108.9 μmol·g-1·h-1 compared to individual components (g-C3N4: 13.5 μmol·g-1·h-1, ZnCdS: 45.3 μmol·g-1·h-1). The improvement of its photocatalytic activity is mainly attributed to the heterojunction formation and resulting synergistic effect, which provide more channels for charge carrier migration and reduce the recombination of photogenerated electrons and holes. Meanwhile, the g-C3N4‒ZnCdS heterojunction catalyst also showed higher stability over a number of repeated cycles. Our work sheds insight of using g-C3N4 and metal sulfide combination to develop low-cost, efficient, visible-light active hydrogen production photocatalysts.

This paper aims to study the performance of solar collectors with various sizes under different weather conditions of different Japanese cities, i.e. Kofu city, Nagoya city and Yamagata city. The heat generated from the solar collector was used to conduct a biogas dry reforming reactor in order to produce H2 to feed a solid oxide fuel cell (SOFC). This study has revealed that the output temperature of solar collector, Tfb in April and July was higher than that in January and October irrespective of city. The optimum length of absorber (dx) of the collector was 4 m irrespective of city. It was clarified that Tfb in Yamagata city in January and October, i.e. winter and autumn is lower than that in Kofu city and Nagoya city especially, which is influenced by the tendency of a solar intensity (I) strongly, not velocity of surrounding air (ua). On the other hand, Tfb is almost the same in April and July, i.e. spring and summer, irrespective of city. The amount of produced H2 from the biogas dry reforming reactor and the power generated by SOFC using H2 in spring and summer were higher compared to the other seasons irrespective of city. This study has revealed that the highest available households number per month was 4.7 according to the investigation in this study.

The integration of clean energy generation with wastewater treatment holds promise for addressing both environmental and energy concerns. Focusing on photocatalytic hydrogen production and wastewater treatment, the study introduces PdIn/TiO2 catalysts for the simultaneous removal of the pharmaceutical contaminant paracetamol and hydrogen production. Physicochemical characterization showed a high distribution of Pd and In on the support as well as a high interaction with it. The Pd and In deposition enhances the light absorption capability and significantly improved HER in comparison to TiO2 not only in the electrolyte but also in presence of paracetamol. Regarding PTM oxidation, TiO2 and PdIn/TiO2 showed an irreversible behavior toward the PTM oxidation, limited by the adsorption of species on the electrode surface. Thus, PdIn-doped TiO2 stands out as a promising catalyst, showcasing enhanced physicochemical properties and superior catalytic performance. This underscores its potential for both environmental remediation and sustainable hydrogen production.

The H2-ICE project aims at developing, through numerical simulation, a new generation of hybrid powertrains featuring a hydrogen fueled Internal Combustion Engine (ICE) suitable for 12-meter urban buses, in order to provide a reliable and cost-effective solution for the abatement of both CO2 and criteria pollutant emissions. The full exploitation of the potential of such a traction system requires a substantial enhancement of the state of the art since several issues have to be addressed. In particular, the choice of the more suitable fuel injection system, as well as the control of the combustion process, are extremely challenging. Firstly, a high-fidelity 3D-CFD model will be exploited to analyze the in-cylinder H2 fuel injection through supersonic flows. Then, after the optimization of the injection and combustion process, a 1D model of the whole engine system will be built and calibrated allowing the identification of a “sweet spot”, in the ultra-lean combustion region, characterized by extremely low NOx emissions and, at the same time, high combustion efficiencies. Moreover, to further enhance the engine efficiency well above 40 %, different Waste Heat Recovery (WHR) systems will be carefully scrutinized, including both Organic Rankine Cycle (ORC)-based recovery units as well as electric turbo-compounding. A Selective Catalytic Reduction (SCR) aftertreatment system will be developed to further reduce NOx emissions to near-zero levels. Finally, a dedicated torque-based control strategy for the ICE coupled with the Energy Management Systems (EMS) of the hybrid powertrain, both optimized by exploiting Vehicle-To-Everything (V2X) connection, allow targeting an H2 consumption of 0.1 kg/km. Technologies developed in the H2-ICE project will enhance the know-how necessary to design and build engines and after-treatment systems for the efficient exploitation of H2 as a fuel, as well as for their integration into hybrid powertrains.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

A vehicle boom barrier gate system is one of the recently developed technologies operating at the entrances to the restricted areas. This paper aims to design and control of vehicle’s boom barrier gate system using robust augmentation technique. H 2 optimal and H infinity synthesis controllers are used to improve the performance of the system. The open loop response analysis of the vehicle boom barrier gate system shows that the input of the system need to be improved. Comparison of the vehicle boom barrier gate system with H2 optimal and H infinity synthesis controllers have been done to track a set point desired angular position using a step and operational open and close input signals and a promising results have been observed.

This paper mainly analyzes the design and control of the rotational inverted pendulum, and presents a state space expression. Since the system is highly unstable a feedback control system is used. Augmentations with weighting functions based mixed sensetivity and H2 optimal control methods are used to make the system stable for uprise position. The rotational inverted pendulum have been simulated and compared with the proposed controllers and a promising results have been analyzed sussesfuly.

In this paper, the design and control of a hydraulic system based tire changer machine have been analyzed and simulated using Matlab/Simulink Toolbox successfully. The machine have a displacement input which is a leg pedal displacement in order to push the piston of the pump to fed the motor with a pressured hydraulic fluid to rotate the tire with an angular speed to mount and dismount it. Augmentation based H_∞ and H₂ optimal synthesis controllers have been used to improve the performance of the machine. Comparison of the proposed controllers for tracking a reference input speed have been done using two reference inputs (step and random) signals. Finally the comparative simulation results proved the effectiveness of the proposed tire changer with H synthesis controller in improving the settling time and percentage overshoot.

Following the international trend of using hydrogen as combustible in many industry branches, this paper investigates the impact of mixing methane gas with 23% hydrogen (G222) on condensing boilers’ operation. After modeling and testing several boilers with heat exchange surface different designs, the authors gathered enough information to introduce a new concept, namely High-Performance Condensing Boiler (HPCB). All the boilers that fit into this approach have the same operational parameters at nominal heat load, including the CO2 concentrations in flue gases. After testing a flattened pipes condensing boiler, a CO2 emission reduction coefficient of 1.1 was determined, when converting from methane gas to G222 as combustible. Thus, by inserting into the national grid a G222 mixture, an important reduction in greenhouse gases can be achieved. For a 28 kW condensing boiler the annual reduction in CO2 emissions averages 1.26 tons, value which was experimentally obtained and is consistent with the theoretical evaluation.

With increasing constraints on energy and resource markets and the non-decreasing trend in energy demand, the need for relevant clean energy generation and storage solutions is growing and is gradually reaching the individual home. But small-scale energy storage is still an expensive investment in 2022 and the risk/reward ratio is not yet attractive enough for individual homeowners. One solution is for homeowners not to store excess clean energy individually but to produce hydrogen for mutual use. In this paper a collective production of hydrogen for a daily filling of a bus is considered. Following our previous work on the subject, the investigation consists of finding an optimal buy/sell rule to the grid, and the use of the energy with an additional objective: mobility. The dominant technique in the energy community is reinforcement learning, which is however difficult to use when the learning data is limited as in our study. We chose a less data-intensive and yet technically well-documented approach. Our results show that rulebooks, different but more interesting than the usual robust rule, exist and can be cost-effective. But they require fine-tuning as to not deteriorate system performance. In some cases, it is worth missing the H2 production requirement in exchange for higher economic performance.

Renewable sources and electric distribution network can produce or make available a surplus of electric and thermal energies. The Intermediate Temperature Solid Oxide Electrolyzer (IT-SOE) fed by CO2-steam mixtures can store these electric and thermal energies producing CO-H2 mixtures with high conversion efficiency. Inside the IT-SOE, the CO2-steam mixtures are converted to CO-H2 mixtures and O2 through the cathode and anode electrochemical reactions and reverse water gas shift chemical reaction. In this article an IT-SOE stack fed by different types of steam mixtures was tested at different operating temperatures and the stack polarization and electric power curves were detected experimentally. At the highest hydrogen production operating temperature of the stack fed by steam mixtures, the experimental polarization and electric power curves of the stack fed by steam and CO2-steam mixtures were compared. A simulation model of the IT-SOE system (stack and furnace) fed by CO2-steam mixtures was formulated ad hoc and implemented in a Matlab environment and experimentally validated. At the highest hydrogen production stack operating temperature, the IT-SOE system thermal equilibrium current was evaluated through the simulation model. Moreover, the influence of this current on the IT-SOE system efficiency and the CO-H2 mixture degree of purity was highlighted.

Reactive oxygen species (ROS) encompass various molecular oxygen derivatives naturally produced during aerobic metabolism, including superoxide anion, hydrogen peroxide, and hydroxyl radical. Excessive ROS production leads to oxidative distress, causing cellular damage and contributing to various pathologies, often alongside inflammation. Endogenous sources of ROS include mitochondrial activity and NADPH oxidases. The antioxidant system, comprising enzymes such as superoxide dismutase, peroxiredoxin, and catalase, mitigates ROS-induced damage. This review explores the regulation of ROS by membrane receptors, focusing on B1 and B2 kinin receptors and histamine H2 receptors, which are implicated in vasodilation, angiogenesis, inflammation, and gastric acid secretion. Understanding these interactions provides insights into ROS modulation and its role in disease mechanisms.

We present a critical analysis of the mechanism of reversible hydrogen evolution reaction based on thermodynamics of hydrogen processes considering atomic and ionic species as intermediates. Clear distinction between molecular hydrogen evolution/oxidation (H$_2$ER and H$_2$OR) and atomic hydrogen evolution/oxidation (HER and HOR) reactions is made. It is suggested that the main reaction describing reversible H$_2$ER and H$_2$OR in acidic and basic solutions is: $\ce{H3O^+} + 2e^- \xrightleftharpoons{\mathrm{({H}_{2}^{+}})_{ad}} \ce{H2} + \ce{OH^-}$, which proceeds via the formation of hydrogen molecular ion as intermediate and its potential is $E^{0}$ = 0.414~V (at the standard Hydrogen electrode SHE scale). We analyse experimentally reported data with models which provide \emph{quantitative} match (R.J.Kriek et al., Electrochem. Sci. Adv. e2100041 (2021)). The experimentally observed slope of $\lg(Current)$ vs. $Potential$ equal to $\approx 30$~mV/dec corroborates the presented model of H$_2$ER/H$_2$ER based on \ce{H2$^+$} as intermediate.

The research paper presents a new approach towards constructing motion equations for structures with attached MTMDs (multiple tuned mass dampers). A primary system, with MDOF (multiple dynamic degrees of freedom) was reduced to an equivalent system with a SDOF (single degree of freedom) through the modal approach, and equations from additional MTMDs were added to a thus-created system. Optimization based on H2 and H∞ for the transfer function associated with the generalized displacement of an SDOF system. The research work utilized GA (genetic algorithms) and SA (simulated annealing method) optimization algorithms to determine the stiffness and damping parameters for individual TMDs. The effect of damping and stiffness (MTMD tuning) distribution depending on the number of TMDs was also analyzed. The paper also reviews the impact of primary system mass change on the efficiency of optimized MTMDs, as well as confirms the results of other authors involving greater MTMD effectiveness relative to a single TMD.

In this paper, a metal cutting machine position control have been designed and simulated using Matlab/Simulink Toolbox successfully. The open loop response of the system analysis shows that the system needs performance improvement. Static output feedback and full state feedback H₂ controllers have been used to increase the performance of the system. Comparison of the metal cutting machine position using static output feedback and full state feedback H₂ controllers have been done to track a set point position using step and sine wave input signals and a promising results have been analyzed.

Considering the high potential of hydrogen (H₂) as a clean energy carrier, the implementation of high performance and cost-effective biohydrogen (bioH₂) purification techniques is of vital importance, particularly in fuel cell applications. In this context, membrane technology is a potentially energy-saving solution to obtain high-quality biohydrogen. The most promising poly(ionic liquid) (PIL) - ionic liquid (IL) composite membranes previously studied by our group for CO₂/N₂ separation, containing pyrrolidinium-based PILs with fluorinated or cyano-functionalized anions, were chosen as starting point to explore the potential of PIL–IL membranes for CO₂/H₂ separation. The CO₂ and H₂ permeation properties at the typical conditions of biohydrogen production (T =308 K and 100 kPa of feed pressure) were measured and discussed. PIL–IL composites prepared with [C(CN)₃]^– anion showed higher CO₂/H₂ selectivities and H₂ diffusivities compared to those containing [NTf₂]^– anion. All the membranes revealed CO₂/H₂ separation performances above the upper bound for this specific separation, highlighting the composite incorporating 60 wt% of [C₂mim][C(CN)₃] IL.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

In this study, high-performance FAU (NaY type) zeolite membranes were successfully synthesized using small-sized seeds of 50 nm, and their gas separation performance was systematically evaluated. Employing nano-sized NaY seeds and an ultra-dilute reaction solution with a molar composition of 80 Na2O: 1Al2O3: 19 SiO2: 5000H2O, the effects of synthesis temperature, crystallization time, and porous support (α-Al2O3 or mullite) on the formation of FAU membranes were investigated. The results illustrated that further extending the crystallization time or increasing the synthesis temperature led to the formation of a NaP impurity phase on the FAU membrane layer. The most promising FAU membrane with a thickness of 2.7 µm was synthesized on an α-Al2O3 support at 368 K for 8 h, and had good reproducibility. The H2 permeance of the membrane was as high as 5.34×10-7 mol/(m2 s Pa), and the H2/C3H8 and H2/i-C4H10 selectivities were 183 and 315, respectively. The C3H6/C3H8 selectivity of the membrane was as high as 46 with a remarkably high C3H6 permeance of 1.35× 10-7 mol/(m2 s Pa). The excellent separation performance of the membrane is mainly attributed to the thin, defect-free membrane layer and relatively wide pore size (0.74 nm).

To realize structural vibration control,a two parameters H2 optimization design was proposed to optimize the tuning ratio and damping ratio for electromagnetic tuned mass damper (EMTMD). The control effect of this two parameters optimization design is better than that of classical tuned mass damper (TMD).For this two parameters optimization,the most important thing is that the inductance of the coil can be set very small and the external load resistance can be positive ,which can avoid the use of complex negative impedance circuit. If Ref.[6] were designed according to the H2 optimization of two parameters, the EMTMD can be used for multi-modal vibration control of structures without connecting negative inductance and negative resistance spontaneously.

In this paper, the stability control of the inverted pendulum on a cart with a disturbance forces has been done using observer based and full state feedback H2 controllers. The Lagrangian equation has been used to model the system equation of motions and linearized the system to the unstable upward position. Comparison of the system stability has been simulated by comparing the proposed controllers using Matlab/Scripts and a promising results has been analyzed successfully.

In this paper, the design of a low cost portable ventilator with performance analysis have been done to solve the scarcity of respiratory ventilators for COVID-19 patients. The materials used to build the system are: DC motor, rotating disc and pneumatic piston. The system input is the patient heart beat and the output is volume of air to the patient lung with adjusted breathing rate. This ventilator adjusts the breathing rate to the patient depending on his heart beat rate. The performance analysis of this system have been done using Proportional Integral Derivative (PID) and Full State Feedback H2 controllers. Comparison of the system with the proposed controllers have been done using a step change and a random change of the patient heart beat and a promising result have been analyzed successfully.

Hydrogen gas is seeping from the sedimentary basin of São Franciso, Brazil. The seepages of H₂ are accompanied by helium whose isotopes reveal a strong crustal signature. Geophysical data indicates that this intra-cratonic basin is characterized by i) a relatively high geothermal gradient, ii) deep faults delineating a horst and graben structure and affecting the entire sedimentary sequence, iii) an archean to paleoproterozoïc basements enriched in radiogenic elements and displaying mafic and ultramafic units, and iv) a possible karstic reservoir located 400 m below the surface. The high geothermal gradient could be due to a thin lithosphere enriched in radiogenic elements, which can also contribute to a massive radiolysis process of water at depth, releasing an important amount of H₂. Alternatively, ultramafic rocks that may have generated H₂ during their serpentinization are also documented in the basement. The seismic profiles show that the faults seen at the surface are deeply rooted in the basement, and can drain deep fluids to shallow depths in a short time scale. The carbonate reservoirs within the Bambuí group which forms the main part of the sedimentary layers are crossed by the fault system and represent good candidates for temporary H₂ accumulation zones. The formation by chemical dissolution of sinkholes located at 400 m depth might explain the presence of sub-circular depressions seen at the surface. These sinkholes might control the migration of gas from temporary storage reservoirs in the upper layer of the Bambuí formation to the surface. The very high fluxes of H₂ escaping out of these structures which have been recently documented are, however, in disagreement with the newly developed H₂ production model in the Precambrian continental crust. They either question the validity of these models or the measurement methodology.

Oxidation reactions on semiconducting metal oxides (SMOs) surfaces have been extensively worked on in catalysis, fuel cells, and sensors. SMOs engaged powerfully in energy-related applications such as batteries, supercapacitors, solid oxide fuel cells (SOFCs), and chemical gas sensors. The deep understanding of SMO surface and oxygen interactions and defect engineering has become significant because all those mentioned applications are based on the adsorption/absorption and consumption/transportation of adsorbed (physisorbed-chemisorbed) oxygen. More understanding of adsorbed oxygen and oxygen vacancies (〖V_O^•,V〗_O^(••)) is needed, as the former is the vital requirement for sensing chemical reactions, while the latter facilitates the replenishment of adsorbed oxygen ions on the surface. We determined the relation between sensor response (sensitivity) and the amounts of adsorbed oxygen ions (O_(2(ads))^-,O_((ads),)^- O_2(ads)^(2-),O_((ads))^(2-)), water/hydroxide groups (H2O/OH^-), oxygen vacancies (〖V_O^•,V〗_O^(••)), and ordinary lattice oxygen ions (O_lattice^(2-)) as a function of temperature. During hydrogen (H2) testing, the different oxidation states (W6+, W5+, and W4+) of WO3 were quantified and correlated with oxygen vacancy formation (〖V_O^•,V〗_O^(••)). We used a combined application of XPS, UPS, XPEEM-LEEM, and chemical, electrical and sensory analysis for H2 sensing. We established a correlation between the H2 sensing mechanism of WO3, sensor signal magnitude, the amount of adsorbed oxygen ions, and sensor testing temperature. This paper also provides a review of the detection, quantification, and identification of different adsorbed oxygen species. The different surface and bulk-sensitive characterization techniques relevant to analyzing the SMOs-based sensor are tabulated, providing the sensor designer with the chemical, physical, and electronic information extracted from each technique.

Gas electron multipliers (GEMs) with wire (WGEMs) or metal electrodes (MGEMs), which don’t use any plastic insulators between electrodes are created. The chambers containing MGEMs (WGEMs) with pin-anodes are proposed as detectors for searching of spin-dependent interactions between Dark Matter (DM) particles and gases with nonzero-spin nuclei (H2, D2, 3He, 21Ne, CF4, CH4, etc.). In this paper, we present a review of such chambers. For investigation of the gas mixtures Ne+10%H2, H2 (D2) +3ppmTMAE, the chamber containing WGEM with pin-anode detection system was constructed. In this paper we present the results of an experimental study of these gaseous mixtures exited by an α - source. Mixture of Ar + 40 ppm C2H4 and mixture 50% Xe + 50%CF4 have been investigated. The spatial distributions of photoelectron clouds produced by primary scintillations on α- and β-particle tracks, as well as the distributions of photoelectron clouds due to photons from avalanches at the pin-anode, have been measured for the first time. In our experiments as another filling of the chambers for search of low-mas WIMP (<10 GeV/c2), solar neutrino and solar axions with spin-dependent interaction we propose to use the mixtures: D2 + 3ppmTMAE, 3He + 3%CH4, 21Ne + 10%H2, at pressure 10-17 bar. And in our experiment with liquid gases is used the mixtures with 19F (LAr + CF4, LXe + CF4) and mixture LCH4 + 40ppm TMAE. The time projection chamber (TPC) with the mixture D2 + 3ppmTMAE filling allow to search of spin-dependent interactions of solar axions and deuterium. As well as we present the detecting systems for search of narrow pp-resonances (quarks) in accelerators experiments.

The results shown in this paper extend our research group's previous work, which presents the theoretically achievable hydrogen engine-out NOx (H2-NOx) Pareto front of a hydrogen hybrid electric vehicle (H2-HEV). While the Pareto front is calculated offline, which requires significant computing power and time, this work presents an online-capable algorithm to tackle the energy management of a H2-HEV with explicit consideration of the H2-NOx trade-off. Through the inclusion of realistic predictive data on the upcoming driving mission, a model predictive control algorithm (MPC) is utilized to effectively tackle the conflicting goal of achieving low hydrogen consumption while simultaneously minimizing the NOx. In a case study it is shown that the MPC is able to satisfy user-defined NOx limits over the course of various driving missions. Moreover, a comparison to the optimal Pareto front highlights the MPC's ability to achieve close-to-optimal fuel-performance for any desired cumulated NOx target on four realistic routes for passenger cars.

Arabidopsis contains eight different h-type thioredoxins (Trx) being distributed in different cell organelles. Although Trx h2 is deemed to be localized in mitochondria, its subcellular localization and function remains a matter of debate. Here, Trx h2 localization and function were investigated using cell fractionation studies and reverse genetics. Differential centrifugation and immunodetection showed the Trx h2 protein to be distributed to the microsomal fraction rather than to mitochondrial preparations. To analyze whether Trx h2 has different roles than mitochondrial Trxs, Arabidopsis mutants lacking Trx h2 were compared with mutants deficient in mitochondrial Trx o1 and double mutants with joint deficiencies in both Trxs. Under constant medium light, trxh2 grew as the wild type, while trxo1 and trxo1h2 mutants showed impaired growth. This was accompanied by differences in the metabolite profiles. The trxo1 and trxo1h2 mutants clustered differently from the wild type during the night, revealing a decrease in ascorbate and glutathione redox states. In fluctuating light intensities, genotypic differences in growth rates were attenuated. Compared to the wild type, the fluctuating-light induced decrease in the NADPH/NADP ratio was diminished in the mutants, with the trxo1h2 double mutant showing the strongest effect. This was accompanied by an increase in the photosynthetic efficiency of the trxo1h2 mutant, specifically in the high light phases of fluctuating light. Conclusively, these results support the view that Trxs o1 and h2 are localized in different subcellular compartments, and have different effects on ascorbate and glutathione redox states and growth in medium light, but cooperatively affect NADP(H) redox state and photosynthetic efficiency in fluctuating light.

An energy production system consisting solar collector, biogas dry reforming reactor and solid oxide fuel cell (SOFC) was assumed to be installed in Kolkata, India. This study aims to understand the impact of climate condition on the performance of solar collectors with different lengths of parabolic trough solar collector (dx) and mass flow rate of heat transfer fluid (m). In addition, this study has evaluated the amount of H2 produced by biogas dry reforming (GH2), the amount of power generated by SOFC (PSOFC) and the maximum possible households (N) whose electricity demand could be met by the energy system proposed, considering the performance of solar collector with the different dx and m. As a result, the optimum dx was found to be 4 m. This study revealed that temperature of heat transfer fluid (Tfb) decreased with the increase in m. Tfb in March, April and May was higher than that in other months, while Tfb from June to December was the lowest. GH2, PSOFC and N in March, April and May were higher than that in other months irrespective of m. The optimum m was 0.030 kg/s.

Background. Epidemiological and clinical studies demonstrated that excessive salt intake causes severe hypertension and exacerbated organ derangement such as chronic kidney disease (CKD). In this study, we focused on evaluating histological and gene-expression findings in the kidney using stroke-prone spontaneously hypertensive rats (SHRSP) with high-salt intake and thromboxane A2/ prostaglandin H2 receptor (TPR) blocker ONO-8809. Methods. SHRSP aged 6 weeks were divided into three groups eating normal chow containing 0.4% NaCl, 2.0%NaCl, or 2.0%NaCl +ONO-8809 (0.6mg/kg p.o. daily). Histological analyses with immunohistochemistry and a gene-expression assay with a DNA kidney microarray were performed after 8 weeks. Results. The following changes were observed with high-salt intake. Glomerular sclerotic changes were remarkably observed in the juxtaglomerular cortex areas. ED1, MCP-1, nitrotyrosine, and HIF-1α staining areas were increased in the glomeruli and interstitial portion. Tbxa2r which encodes TPR, Prcp, and Car7 were significantly underexpressed in the kidney. The plasma 8-isoprostane level was significantly elevated, and was attenuated with ONO-8809 treatment. Conclusion. TXA2 and oxidative stresses exaggerated renal dysfunction in salt-loading SHRSP, and ONO-8809 as a TPR blocker suppressed these changes. Therefore, ONO-8809 is a candidate drug to prevent CKD for hypertensive patients associated with high-salt intake.

The cement industry is a significant contributor (around 8 %) to CO2 global emissions. About 60 % of emissions come from limestone calcination, essential for clinker production, while 40 % result from fuel combustion. Reducing these emissions is challenging due to limestone’s role as the primary raw material for cement. Cement plants are required to achieve carbon neutrality by 2050, as outlined in the 13th United Nations Sustainable Goals. One strategy to achieve this goal, involves Carbon Capture and Utilisation (CCU). Among the options for CO2 utilisation, the Power-to-Liquid (PtL) strategy offers a means to mitigate CO2 emissions. In PtL, CO2 captured from cement industrial flue gas is combined with hydrogen generated by renewable electrolysis (green hydrogen) and catalytically converted into renewable methanol (e-MeOH). In this sense, this review provides a comprehensive overview of the worldwide existing pilot and demonstration units, and projects funded by EU across several industries. It specifically focuses on PtL technology worldwide within cement plants. This work covers 18 locations worldwide, detailing technology existent at plants of different capacities, location, and project partners. Finally, the review analyses techno-economic assessments related to e-MeOH production processes, highlighting the potential impact on achieving carbon neutrality in the cement industry.