In this experimental work, pure nickel oxide and Al-doped NiO thin films have successfully been elaborated onto glass substrates by solar spray pyrolysis technique. The substrates were heated at around 450°C using a solar heater (furnace). The structural, optical and electrical properties of the elaborated Al-doped films have been studied at different atomic percentage ratios (0, 0.5, 1, 1.5 and 2 at. %). The results of Al-doped NiO films XRD patterns were, the formation of (NiO) phase under a cubic crystalline structure (polycrystalline) with a strong favored orientation along (111) plane were noticed at all sprayed films. When Al doping ratio reaches 1 at.%, an growth in crystallite size over 31.9 nm was obtained denoting the nano-structure of the product, which confirmed by SEM images. In addition, aluminum oxide Al₂O₃ was clearly observed at 1.5 at.% Al ratio. Otherwise, all thin films have a good optical transmission in the visible region of about 65%, the optical band gap energy decreased from 3.69 to 3.64 eV with increasing Al doping ratio. It is shown that the layer deposited with 0.5 at.% has less disorder with few defects. The investigation on electrical properties of elaborated thin films confirmed that the conductivity of NiO films was improved, after doping them with Al which affirms their p-type character of semiconductor. However, an addition of an excessive quantity of Al content causes the formation of Al₂O₃ which leads to a decrease in the conductivity. It is worth mentioning that the Al content of 0.5 at.% is the optimum ratio in terms of electrical conductivity and formation defect. Al-doped NiO can be used in various optoelectronic devices due to its good transparency and high electrical conductivity.

In this work, effects of 20 transition element additives on the interfacial adhesion energy and electronic structure of Al (111)/6H-SiC (0001) interfaces have been studied by first principles method. For clean Al (111)/6H–SiC (0001) interfaces, both Si-terminated and C-terminated interfaces have covalent bond characteristics. The C-terminated interface has stronger binding energy, which is mainly due to the stronger covalent bond formed by the larger charge transfer between C and Al. The results show that the introduction of many transition elements, such as 3d transitional group Mn, Fe, Co, Ni, Cu, Zn and 4d transitional group Tc, Ru, Rh, Pd, Ag, can improve the interfacial adhesion energy of the Si-terminated Al (111)/6H-SiC (0001) interface. However, for the C-terminated Al (111)/6H-SiC (0001) interface, only the addition of Co element can improve the interfacial adhesion energy. Bader charge analysis shows that the increase of interfacial binding energy is mainly attributed to more charge transfer.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

A Chinese superalloy GH4099 (~20 vol.% γ' phase), which can operate for long periods of time at temperatures of 1173-1273 K, was fabricated by electron beam melting (EBM). Argon gas atomized (AA) and plasma rotation electrode process (PREP) powders with the similar composition and size distribution were used as raw materials for comparison. Microstructure and mechanical properties of both the as-EBMed and post-treated alloy samples were investigated. The results show that the different powder characteristics resulted in the different build temperatures for AA and PREP samples, which were 1253 K and 1373 K, respectively. With increasing the building temperature, the EBM processing window shifted towards the higher scanning speed direction. Furthermore, intergranular cracking was observed for the as-fabricated PREP sample as a result of local enrichment of Si at grain boundaries. The cracks were completely eliminated by hot isostatic pressing (HIPing) and did not re-open during subsequent solution treatment and aging (STA). Fine spherical γ' phase precipitated uniformly after STA. The tensile strength of the HIP+STA samples was ~920 MPa in the building direction and ~850 MPa in the horizontal direction, comparable with that of the wrought alloy.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

Carbon (C) cycle n inland waters, including its concentrations and carbon dioxide (CO2) emis-sions from water surfaces are at the forefront of biogeochemical studies, especially in the re-gions, strongly impacted by on-going climate change. Towards better understanding of C stor-age, transport and emission in Central Asian mountain regions, extremely poorly studied until now, here we carried out systematic measurements of dissolved C and CO2 emissions in 15 riv-ers and 5 lakes located along a macro-transect of various natural landscapes in the Sayan-Altai mountain region, from high mountains of the Western Sayan in the northwest of Tyva to arid (dry) steppe and semi-deserts in intermountain basins of the southeast of Tyva, the border with Mongolia. New data on major hydrochemical parameters, CO2 fluxes by floating chambers, dis-solved organic and inorganic carbon concentrations collected over four main hydrological sea-sons allowed to assess the current C biogeochemical status of these water bodies in order to judge possible future changes under climate warming. We further tested the impact of perma-frost, river watershed size, lake area and climate parameters as well as ‘internal’ biogeochemical drivers (pH, mineralization, organic matter quality and bacterial population) on CO2 concentra-tion and emissions in lakes and rivers of this region, and compared them with available data on other subarctic and mountain settings.

Stark widths for 23 transitions in Al IV have been calculated employing modified semiempirical method. The results are obtained for an electron density of 10^17 cm−3 and temperatures from 10,000 K up to 160,000 K. The results obtained in this investigation are used for the examination of the influence of Stark broadening in Al IV stellar spectra, as well as to check Stark width regular behavior and similarites within Al IV spectrum.

In this study, Li-Al-OH layered double hydroxide (LDH), which was prepared by solvent-free one-step mechanochemical reaction of LiOH and Al(OH)₃, was applied to remove boron from aqueous solution. Dry-grinding for 3 h at a rotational speed of 500 rpm, Li/Al molar 1/2 was the optimum condition to prepare highly crystalline of Li-Al LDH phase with no evident impure phases. Two milling products with Li/Al molar ratio at 1/2 and 2/2 were evaluated for boron adsorption. The results confirmed that Li/Al molar ratio 2/2 sample showed high boron adsorption capacity due to the physical adsorption of Li-Al-OH LDH and chemical synergism of phase gel Al(OH)₃. The adsorption isotherms, described by the Langmuir model, indicated maximum monolayer boron uptake capacity 45.45 mg/g, implying competitive adsorption capacity of the material in our experiment.

Background: Eid al-Adha is celebrated every year in Muslim countries; however, it is a time when patients present to the emergency department with serious injuries. In our study, we examined current injuries at the time of Eid al-Adha in the largest patient population in one of the largest hospitals in Turkiye, including tendon injury map and maxillofacial injuries for the first time in the literature. Methods: Between 2019 and 2023, patients admitted to Ankara City Hospital during Eid al-Adha were examined. The demographic characteristics, injury patterns, and injury sites of the patients were evaluated by analyzing the patients admitted on the four days of Eid al-Adha. Statistical analysis were performed using IBM SPSS Statistics for Windows. Results: Six hundred and ten patients, including 101 female and 509 male patients, were included in this study. There was a statistically significant increase (p

Research on the development of new lightweight Al-Li alloys using selective laser melting pro-cess has great potential for industrial applications. This paper reports on the development of novel aluminum-lithium alloys using selective laser melting technology. Al-Cu-Li-Mg-Ag-Sc-Zr pre-alloyed powders with lithium contents of 1 wt.%, 2 wt.% and 3 wt.%, respectively, were prepared by inert gas atomization. After SLM process optimization, the microstructure and me-chanical properties of the as-formed specimens were investigated. The densification of the three newly developed alloys are 99.51 %, 98.96 % and 92.01 %, respectively. They all have good form-ability, with the lithium loss rate about 15 %. The as-formed alloy with 1% Li content presents good comprehensive properties with a yield strength of 412.6 ± 16.0 MPa, an ultimate tensile strength of 461.1 ± 11.7 MPa, and an elongation of 13.6 ± 1.1%. The three alloys exhibit a layered molten pool stacking morphology and have a typical heterostructure. The columnar crystals and equiaxed fine grains are alternately arranged, and most of the precipitated phases are enriched at the grain boundaries. The change of Li content mainly affects the precipitation of Cu-containing phase. When the Li content is 1 wt.%, there are θ phase, T1 phase and TB phase. When Li increased to 2 wt.%, T1 and T2 phases precipitated together. When Li reaches 3 wt.%, δ' phase precipitates with T2 phase. This study provides useful guidance for the future SLM form-ing of new crack-free and high-strength Al-Li alloys.

Q345 steel is widely used in the construction industry, vehicle manufacturing industry, bridge construction industry and many other aspects due to its excellent comprehensive performance. However, due to its high silicon content, direct hot-dip galvanizing will lead to a series of problems, such as easy peeling of the coating due to the "silicon reactivity". In this paper, we adopt the "two-step hot-dipping method", first hot-dip aluminizing and then hot-dip galvanizing, to isolate the substrate and zinc liquid direct contact, so as to avoid the occurrence of "silicon reactivity". Through the microstructure characterization, neutral salt spray corrosion experiments, electrochemical experiments, the results show that: Al-Zn composite coatings from the inside out were perpendicular to the substrate growth of loose Fe2Al5 layer and Al-Zn layer, outbursts generation; Al-Zn composite coatings resistance to neutral salt spray corrosion was far more than the substrate; Al-Zn composite coatings polarization curve corrosion potential than the substrate was lower than that of the substrate by 0.512V, showing a strong corrosion resistance. It shows extremely strong corrosion resistance.

Reductive leaching in the Bayer cycle using of iron (2+) allows Al extraction to be significantly increased by magnetization of Al-goethite and Al-hematite. However, the use of expensive iron (2+) salts or iron powder as a source of iron (2+) leads to a significant increase in production costs. In this work, the feasibility of a new method, the reductive leaching of bauxite using an electrolysis process, was investigated. Reduction of iron minerals of boehmitic bauxite in both Bayer solution and purely alkaline solutions were carried out. Experiments were performed using a plate cathode and a bauxite suspension in alkaline solution, as well as using a bulk cathode with a stainless-steel mesh at the bottom of the cell as the current supply. During the electrolysis process, the potential of the cathode relative to the reference electrode was measured as a function of current at different concentrations of solid (100-300 g L–1) and suspension temperatures (95-120 °C). It is shown that the current efficiency using suspension and plate cathode with the predominant deposition of Fe doesn’t exceed 50% even with the addition of magnetite to increase the contact of solid phase with the current supply. With the use of a bulk cathode, the reduction of iron minerals leads predominantly to the formation of magnetite with the efficiency of using electric current more than 80%. As a result of preliminary desilication and electroreduction it is possible to extract more than 97% of Al from bauxite, and to increase the iron content in the bauxite residue to 57-58%.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

Herein, we report on a versatile system composed of two Ni(II)-based coordination compounds: a 3D metal-organic framework of {[Ni(μ-3isoani)2]·DMF}n (1) formula and a 0D monomeric [Ni(3isoani)2(H2O)4] (2) complex (where 3isoani = 3-aminoisonicotinato and DMF = dimethylformamide) which show mutual solvent-induced reversible transformations into each other. These 1 ↔ 2 transformations are triggered by the exposure of one compound to the solvent present in the other, that is, the MOF (1) in water and the monomer (2) in DMF. The process is easily followed by the naked eye because it involves a colour change from green (1)-to-brownish green (2), making the system potentially interesting to act as a sensor of those solvents. Moreover, these compounds present very different magnetic properties since 1 shows field-induced single-molecule magnet (SMM) behaviour, which corresponds to one of the few Ni(II)-based compounds showing this property, whereas 2 behaves as a regular paramagnet, all of which is explained according to a careful study of the magnetic properties by means of experimental direct-current (dc) and alternating-current (ac) measurements as well as complete active space self-consistent field (CASSCF) calculations.

In this work, we have proposed two new methods for the synthesis of [TcO2L4]+ (where L = im-idazole (Im), methylimidazole (MeIm)) complexes using thiourea (Tu) and Sn(II) as reducing agents. The main and by-products of the reactions were determined, and possible reaction mechanisms were proposed. We have shown that the reduction of Tc(VII) with thiourea is ac-companied by the formation of the Tc(III) intermediate and further oxidation to Tc(V). The reac-tion conditions changing can lead to the formation of Tc(VII) and Tc(IV) salts. Seven new crystal structures are described in this work: Tc(V) complexes, salts with Tc(VII) and Tc(IV) anions. For halide salts of Tu the cell parameters were determined. In all obtained compounds, except for [TcO2(MeIm)4]TcO4, there are π-stacking interactions between aromatic rings. An increase in the anion size lead to weaken intermolecular interactions. Halogen bonds and anion-π interactions have also been found in hexahalide-containing compounds. The Hirshfeld surface analysis showed that the main contribution to the crystal packing is made by van der Waals interactions of the H···H type (42.5–55.1%), H···C/C ···H (17.7–21.3%) and hydrogen bonds, which contribute 15.7–25.3% in total.

In laser joining of copper (Cu) and aluminum (Al) sheets, the Al sheet is widely chosen as the top surface for laser irradiation because of increased absorption of laser beam and lower melting temperature of Al in contrast to Cu. This research focus on welding from Cu side to Al sheet. The main objective of irradiating the laser beam from the copper side (Cu on top) is to exploit higher solubility of Al in Cu. A significantly lower laser power can be used with 515 nm laser in comparison to 1030 nm. In addition to low laser power, a stable welding is obtained with 515 nm. Because of this advantage, 515 nm is selected for the current research. By fusion of Cu and Al the two sheet metals are welded, with presence of beneficial Cu solid solution phase and Al+Al2Cu in the joint with the brittle phases intermixed between the ductile phase. Therefore the mixed composition strengthens the joint. However excessive mixing leads to formation of more detrimental phases and less ductile phases. Therefore optimum mixing must be maintained. Energy dispersive X-ray spectroscopy (EDS) analysis indicate that large amount of beneficial Cu solid solution and Al rich phases is formed in the strong joint. From the tensile shear test for a strong joint, fracture is obtained on the heat-affected zone (HAZ) of Al. Therefore the key for welding from copper side is to have optimum melt with beneficial phases like Cu and Al+ Al2Cu and the detrimental phases intermixed between the ductile phases

To enhance the mechanical properties (i.e. strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis have been conducted. The presence of fcc annealing twins was both observed in the optical microscope (OM) and the scanning electron microscope (SEM) images. Both the strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these 2 alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au.

Ménière's disease (MD) has an unclear cause. The microvascular dysregulation of the inner ear has been increasingly pointed as a potential contributor. This study investigates the prevalence of cardiovascular risk factors (CVRFs) in MD patients compared to those with posterior circulation cerebral infarction (POCI). CVRFs like hypertension, diabetes, dyslipidemia, obesity, coronary heart disease, and smoking were assessed in both MD and POCI patients. Brain MRI identified POCI etiology as "small vessel occlusion" (SVO) or "other etiology" (OE). The study included 64 MD and 84 POCI patients. Compared to MD, POCI OE showed a higher prevalence of CVRFs across various age groups, including hypertension, diabetes, dyslipidemia, and smoking. Notably, the odds of having POCI OE were significantly higher for individuals with hypertension and smoking. On the other hand, POCI SVO showed similar prevalence of CVRFs compared to MD. This study reveals no significant difference in CVRF prevalence between MD and smaller vessel POCI. However, a clear distinction emerges when comparing MD to POCI with involvement of larger blood vessels. Further research is needed to confirm these findings and explore potential shared risk factors between POCI (SVO) and MD.

Zeolite Y with microporous and hierarchical structure containing Ti–Ni and Ti–Co oxides were obtained as active photocatalysts. Different Ti amounts (5, 10% TiO2) were supported, followed by loading of Ni or Co oxides (5 %). The X-ray diffraction evidenced the presence of TiO2 as anatase. N2 adsorption-desorption results showed type IV isotherms, for hierarchical zeolite Y samples, and a combination of type IV and I isotherms, for zeolite Y samples. UV–Vis diffuse reflectance spectra showed shift of absorption band to visible with increasing of Ti loading and especially after Co and Ni addition. A significant effect of the support was evidenced for Ti and interaction with Co/Ni species. The zeolite Y support stabilizes Ti in the 4+ oxidation state while hierarchical zeolite Y support favored the formation of Ti 3+ species and oxidation of Co and especially of Ni to 3+. Photocatalytic activity, under UV and visible light, was evaluated in degradation of amoxicillin, used as a model test. The photocatalytic mechanism was investigated using ethanol, p-benzoquinone and KI as ·OH, ·O2- radicals and hole (h+) scavengers. The best results were obtained for the immobilized Ni-Ti species on hierarchical zeolite Y support.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

This study investigated defect formation and strain distribution in high Mg content Al-Mg alloys during normal rolling and cross-rolling processes. The finite element analysis (FEA) revealed the presence of wave defects and strain localization-induced zipper cracks in normal cold rolling, which were confirmed by experimental results. The concentration of shear strain played a significant role in crack formation and propagation. However, the influence of wave defects was minimal in the cross-rolling process, which exhibited a relatively uniform strain distribution. Nonetheless, strain concentration at the edge and center regions led to the formation of zipper cracks and edge cracks, with more pronounced propagation observed in the experiments compared to FEA predictions. Furthermore, texture evolution was found to be a crucial factor affecting crack propagation, particularly with the development of the Goss texture component which is observed by electron backscattered diffraction analysis at bending points. The Goss texture hindered crack propagation, while the Brass texture allowed cracks to pass through. This phenomenon was consistent with both FEA and experimental observations. To mitigate edge crack formation and propagation, potential strategies involve promoting the formation of the Goss texture at the edge through alloy and process conditions, as well as implementing intermediate annealing to alleviate stress accumulation. These measures can enhance the overall quality and reliability of Al-Mg alloys during cross-rolling processes. In summary, understanding the mechanisms of defect formation and strain distribution in Al-Mg alloys during rolling processes is crucial for optimizing their mechanical properties. The findings of this study provide insights into the challenges associated with wave defects, strain localization, and crack propagation. Future research and optimization efforts should focus on implementing strategies to minimize defects and improve the overall quality of Al-Mg alloys in industrial applications.

This paper presents a methodology to detect the erosion and progradation effects in the Atrato river delta, located in the Gulf of Urabá in Colombia using SAR (Synthetic Aperture Radar) data. Other authors have studied this area by using optical images, encountering difficulties given the persistent presence of clouds in this region. SAR imagery is rescaled, despeckled, composed, classified, registered and processed to obtain a heatmap that shows the overall changes during eight years (2016–2023) in one single image. Since this technology uses microwave active signals, the presence of clouds and other environmental phenomena was not a problem, and all the images from the selected dates could be processed and analyzed. Also, detection of the dynamic processes was obtained for every period considered in this study with respect to the previous one in time, calculating areas and detecting the regions subject to the erosion and progradation processes. The multitemporal analysis performed found that the newly created mouth is the most active area for these processes, coinciding with other studies. A comparison of these findings with the Oceanic Niño Index (ONI) showed a relative delayed coupling to the erosion process and a coupling of progradation with dry and wet seasons.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

A series of defective ZSM-5 zeolites (~300 nm, SiO₂/Al₂O₃ ratio of 55, 100, 400 and 950) were intentionally prepared and systematically studied by XRD, SEM, ²⁹Si MAS NMR, argon physisorption, NH₃-TPD and FT-IR technologies. The nature, the amount and the accessibility of the acid sites of defective ZSM-5 zeolites are greatly different from reported ZSM-5 zeolites with perfect crystal structure. The co-existed strong Brønsted acid sites (Si(OH)Al) and weak Brønsted acid sites (hydroxyl nests) over defective ZSM-5 zeolites might lead to unique catalytic function. Zn(C₂H₅)₂ was grafted onto defective ZSM-5 zeolites through chemical liquid deposition (CLD) method. Interestingly, FT-IR spectroscopy studies find that Zn(C₂H₅)₂ was preferentially grafted on the hydroxyl nests with weak acidity rather than the Si(OH)Al groups with strong acidity over different defective ZSM-5 zeolites. Particularly, home-built operando dual beam FTIR-MS was applied to study the catalytic performance of Zn species locating at different sites of defective ZSM-5 zeolites under n-hexane transformation. Results show that Zn species grafted over hydroxyl nests obtain better dehydrogenation performance than Zn species over framework aluminum. This study provides guidance for the rational design of highly efficient alkane dehydrogenative aromatization catalysts.

This article utilized electrodeposition technology to fabricate Zn and Zn-Y₂O₃-Al₂O₃ composite coatings on Q235 steel plates. The composite coatings were obtained by adding Y₂O₃/Al₂O₃ nanoparticles (0, 5, 10, and 15 g/L) to acidic chloride solutions. This study then examined the impact of these nanoparticles on the microstructure, morphology, microhardness, hydrophobicity, and corrosion resistance of the composite coatings. The results indicate that the addition of the nanoparticles increased the nucleation sites on the surface of the coating, thereby refining the grain size and reducing the roughness of the coating surface. When 10g/L of Y₂O₃ and 10g/L of Al₂O₃ nanoparticles were added, the hardness of the composite coating (369 Hv) was 2.49 times higher than that of the pure Zn coating (148 Hv), which was attributed to the dispersion strengthening and grain refinement effects of the nanoparticles. The corrosion resistance of the Zn and Zn-Y₂O₃-Al₂O₃ composite coatings was studied using linear sweep voltammetry and AC impedance spectroscopy. The addition of the nanoparticles improved the corrosion resistance of the composite coating, and the composite coating prepared in an electrolyte containing 10 g/L of Y₂O₃ and 10 g/L of Al₂O₃ nanoparticles exhibited the best corrosion resistance. Meanwhile, the composite coating exhibited good hydrophobicity, with a contact angle of 120.9°, 1.94 times that of the pure Zn coating (62.2°). The Zn-Y₂O₃-Al₂O₃ nanocomposite coating material has significant potential advantages in the field of steel corrosion.

Deep Learning (DL) and Machine Learning (ML) are widely used in many fields, but rarely used in Frequency Estimation (FE) and Slope Estimation (SE) of signals. Frequency and slope estimation for Frequency-Modulated (FM) and single-tone sinusoidal signals are essential in various applications, such as wireless communications, sonar, and radar measurements. In this work, artificial neural network (ANN) and convolutional neural network (CNN) are used in frequency and slope estimation for FM signals under Additive White Gaussian Noise (AWGN) and Additive Symmetric alpha Stable Noise (SαSN). SαS distributions are impulsive noise disturbances found in many communication environments like marine systems; their distribution lacks a closed-form Probability Density Function (PDF), except for specific cases, and infinite second-order statistic, hence Geometric SNR (GSNR) is used in this work to determine the impulsiveness of noise in a mixture of Gaussian and SαS noise processes. ANN is a machine learning classifier, designed with few layers for reducing FE and SE complexity while getting higher accuracy as compared with classical techniques. CNN is a deep learning classifier, designed with many layers for FE and SE, and proved to be more accurate than ANN when dealing with big data and finding optimal features. Simulation results show that SαS noise can be much more harmful for FE and SE of FM signals than Gaussian noise. DL and ML can significantly reduce FE complexity, memory cost, and power consumption, which is important in many systems such as some Internet of Things (IoT) sensor applications. After training DCNN for frequency and slope estimation of LFM signals, the performance of DCNN (in terms of accuracy) can give acceptable results at very low signal-to-noise ratios where TFD fails, giving more than 20dB difference in the GSNR working range.

We present a general theory of estimation of analysis error covariances based on cross-validation as well as a geometric interpretation of the method. In particular we use the variance of passive observation–minus-analysis residuals and show that the true analysis error variance can be estimated, without relying on the optimality assumption. This approach is used to obtain near optimal analyses that are then used to evaluate the air quality analysis error using several different methods at active and passive observation sites. We compare the estimates according to the method of Hollingsworth-Lönnberg, Desroziers et al., a new diagnostic we developed, and the perceived analysis error computed from the analysis scheme, to conclude that, as long as the analysis is near optimal, all estimates agree within a certain error margin.

Compressive residual stresses in thin films can inhibit crack propagation under normal or sliding contact loading, with associated enhancement of the coating apparent toughness, load bearing capacity and wear resistance. This study investigates the influence of residual stress distributions on the thin film/substrate adhesion using a nanoindenter coupled with scanning electron microscope (SEM) investigations of indentation induced failure modes. Reactive and un-reactive magnetron sputtering with ion plating was used to coat a (100) silicon substrate with aluminum nitride (AlN) with and without an aluminum (Al) adhesion layer. The presence of an Al bond layer gives additional interfacial tensile stress because of the difference in thermal expansion coefficient. Additionally, a different magnitude of residual stresses in the AlN coating was achieved by changing the applied bias voltage onto the substrate. Wafer curvature method and incremental focused ion beam (FIB) milling, combined with high-resolution in situ scanning electron microscopy (SEM) imaging and full field strain analysis by digital image correlation (DIC), were used to measure the average and in-depth stress residual stress distribution in the produced coatings. The adhesion energy was then quantified by using a nanoindentation based model. Results demonstrate that the additional tensile residual stress in the aluminum adhesion layer decrease significantly the coating adhesion, even in presence of a higher compressive stress state in the AlN top-layer. Therefore, the coatings without Al-layer showed better adhesion because of a more homogeneous compressive residual stress in comparison with the coating having Al layer, even though both groups of coatings are produced under same bias voltage. Results are discussed, and some general suggestions are made on the correlation between coating/substrate property combination and the adhesion energy of multilayer stacks. The results suggested that Al bond-layer and inhomogeneous residual stresses affected the adhesion of AlN negatively to a substrate like silicon.

For better export marketing strategies (EMS), companies mobilize their internal resources, which are managerial commitment, firm experience, and product uniqueness. However, Small businesses with constrained resources cannot be well explained with this view. So, more research on how small business come up with EMS have been called for. To explain how resource-restricted firms which rely heavely on entrepreneur, this study adopted the concept of dynamic managerial capabilities (DMCs) and resource versatility to better explain small business exports. We analyzed small businesses in Mongolia with qualitative research methods, including interviews with entrepreneurs and support organizations, site visits, and group discussions. We suggest international dynamic marketing capabilities (IDMCs), which are entrepreneurial orientation, networking capability, and versatile dynamic capability for small business. Theoretical and managerial implications are discussed.

Objectives: Multicentric Osteolysis, Nodulosis, and Arthropathy (MONA) syndrome is a rare genetic skeletal dysplasia. Its diagnosis can be deceptively similar to childhood-onset genetic skeletal dysplasias and juvenile idiopathic arthritis. We aimed to report the syndrome’s clinical and radiologic features with emphasis on skeletal manifestations. And establish relevant phenotype-genotype correlations. Methods: We evaluated two boys, 4-and-7-years-old with MONA syndrome. Both patients had consanguineous parents. We verified the diagnosis by correlating the outcomes of clinical, radiologic and molecular analysis. We specifically evaluated the craniofacial morphology and clinical and radiographic skeletal abnormalities. We contextualized the resultant phenotype-genotype correlations to publications on MONA and its differential diagnosis. Results: Skeletal manifestations were the presenting symptoms and mostly restricted to hands and feet in terms of fixed extension deformity of the metacarpophalangeal and flexion deformity of the interphalangeal joints with extension deformity of big toes. There were arthritic symptoms in the older patient especially of the wrists and minute pathologic fractures. The skeletal radiographs showed osteopenia/dysplastic changes of hands and feet. Both patients had variants in the matrix metalloproteinase2 gene which conformed to phenotype of previously reported literature in one patient while the other had a novel variant which conformed to MONA phenotype. Craniofacial abnormalities were present. However, minimal extra-skeletal manifestations. Conclusion: Overall, there is an emerging distinctive skeletal pattern of involvement in terms of both clinical and radiographic features. This includes age of onset and location of presenting skeletal manifestations, chronological order of joint affection, longitudinal disease progression, specifics of skeletal radiographic pathology and craniofacial features. Nevertheless, physicians are cautioned against differential diagnosis of similar genetic skeletal dysplasias and juvenile idiopathic arthritis.