Urban tree classification is pivotal in urban planning and management, facilitating informed decision-making processes. In this study, we introduce a novel data presentation method termed Pseudo Tree Crown, designed to enhance the accuracy and efficiency of urban tree classification. Leveraging the latest advancements in artificial intelligence (AI), we employ a state-of-the-art classification scheme, PyTorch, to maximize the accuracy of tree classification. Our results demonstrate a robust classification accuracy of over 95% from high spatial resolution imagery from Unmanned Aerial Vehicle (UAV), underscoring our proposed approach’s effectiveness. Moreover, the adaptability of our method renders it applicable to various study areas, highlighting its versatility and potential for widespread implementation in urban planning and management initiatives.

This paper presents the second stage of a tandem fixed wing unmanned aerial vehicle (UAV) aerodynamic development. In the initial stage, the UAV was optimized analyzing its characteristics only in symmetrical flight conditions. Posted requirements were that both wings should produce relevant positive lift, the initial stall must occur on the front wing first, the center of pressure should be close to the center of gravity, while longitudinal static stability should be in the optimum range. Computational fluid dynamics (CFD) analyses were performed, where applied calculation model was derived from the authors’ previous successful projects. The eight version TW V8 has satisfied all longitudinal requirements. Lateral-directional CFD analyses of V8 showed that the ratio of the lateral and directional stability at the nominal cruising regime was optimal, but both lateral and directional static stabilities were too high. On further development versions the lower vertical tail was eliminated, negative dihedral was implemented on the front wing, and four inverted blended winglets were added. Version TW V14 has largely improved lateral and directional stability characteristics, while their optimum ratio at cruising regime was preserved. Longitudinal characteristics were also well preserved. Maximum lift coefficient and lift-to-drag ratio were increased, compared to the V8.

This work presents a new scheme for autonomous control and obstacle detection of a catamaran unmanned surface vessel. Based on the Newtonian mechanics, hydrodynamics, and maneuvering modelling group modelling principles in the attached coordinate system, a three-degree-of-freedom motion model of the catamaran unmanned surface vessel is constructed. The fuzzy inference method is used to overcome the drawback that the traditional PID control cannot tune the PID parameters online, and the trajectory controller is designed. Meanwhile, 3D LIDAR is used to achieve obstacle detection. The results of the trajectory tracking simulations and experiments verify the accuracy of the model design and the effectiveness of the autonomous control design.

Insulator defect detection is of great significance to compromise the stability of the power transmission line. The state-of-the-art network of object detection, YOLOv5, has been widely used on insulator and defect detection. However, YOLOv5 network has some limitations like poor detection rate and high computational loads in detecting small insulator defects. To solve these problems, we proposed a light-weight network for insulator and defect detection. In this network, we introduced Ghost module into YOLOv5 backbone and neck to reduce the parameters and model size to enhance the performance in unmanned aerial vehicles (UAVs). Besides, we added small object detection anchors and layers for small defect detection. In addition, we optimized the backbone of YOLOv5 by applying convolutional block attention module (CBAM) to focus on critical information for insulator and defect detection and suppress uncritical information. The experiment result shows the mean average precision (mAP) 0.5 and the mAP0.5:0.95 of our model can reach 99.4% and 91.7%, the parameters and model weight are reduced to 3807372 and 8.79M, which can easily deploy to embedded devices like UAVs. And the speed of detection can reach 10.9ms/image, which can meet the real-time detection requirement.

Low-cost miniature hyperspectral and thermal cameras onboard lightweight unmanned aerial vehicles (UAV) bring new opportunities for monitoring land surface variables at unprecedented fine spatial resolution with acceptable accuracy. This research applies hyperspectral and thermal imagery from a drone to quantify upland rice growth and water use efficiency (WUE) after biochar application in a Costa Rican dry region. The field flights were conducted over two experimental groups with bamboo biochar and sugarcane biochar amendments and one control group without biochar application. Rice canopy biophysical variables were estimated by inversion of a canopy radiative transfer model on hyperspectral reflectance. Variations in gross primary production (GPP) and WUE across treatments were estimated from the normalized difference vegetation index (NDVI), canopy chlorophyll content (CCC), and evapotranspiration. We found that GPP was increased by 41.9±3.4 % when using bamboo biochar and 17.5±3.4 % when using sugarcane biochar, which was probably due to higher soil moisture in the biochar-amended plots and led to significantly higher WUE by 40.8±3.5 % in bamboo biochar and 13.4±3.5 % in sugarcane biochar. This study demonstrated the use of hyperspectral and thermal imagery from drone to provide indicators for quantifying biochar effects on tropical dry cropland by integrating with ground point samples and physical models.

Tail-sitters aim to combine the advantages of fixed-wing and rotor-craft, but demand a robust and fast stabilization strategy to perform vertical maneuvers and transitions to and from aerodynamic flight. The research conducted in this work intends to assess the performance of nonlinear control strategies to stabilize the attitude of a X-Vert VTOL aircraft when hovering, comparing existing solutions to applications of Nonlinear Dynamics Inversion (NDI) and its incremental version, INDI. Such controllers are implemented and tuned in simulation in order to stabilize a model of the tail-sitter , complemented by estimation methods that allow to feed back the necessary variables. These estimators and controllers are then implemented in a microcontroller, validating them in a Hardware-in-the-Loop (HITL) scenario, with simple maneuvers in vertical flight. Lastly, the developed control solutions are used to stabilize the aircraft in experimental flight, being monitored by a motion capture system. The experimental results allow to validate the model of the X-Vert and compare the effectiveness of the different control solutions in stabilizing it, with the INDI presenting itself as a more robust control strategy, with better tracking capabilities and less actuator demands.

The urban heat island (UHI) and its intensity is one of the phenomena that are of determining importance for the comfort of living in cities and their sustainable development in the face of deepening climate change. The study is objectively difficult due to the large dynamics like land cover and the considerable diversity of land use patterns in urban areas. Various approaches and methods are used in research practice, based both on ground measurements and in the use of remote methods and satellite information. However, most of these approaches provide information with problematic spatial and temporal resolution, making them difficult to apply for sustainable urban planning purposes, which require adequate information provision. This paper presents the results of the application of thermal photogrammetry based on the use of unmanned aerial systems (UAS), combined with geographic information systems (GIS), in the study of surface urban heat island intensity (SUHI), at the local level for the largest housing complex in Bulgaria - Lyulin district of the capital of Sofia city. The studies were carried out during a heat wave in July 2023. A difference of 16.5oC was found between locations with SUHI occurrence and suburban areas. The information benefits of locally addressed data and their direct applicability are discussed to support decision-making processes in the planning and management of urban areas, including their climate adaptation and sustainable development.

This paper describes research on a unique propulsion system design for a low-speed Biomimetic Unmanned Underwater Vehicle (BUUV). It is biomimetic in the sense that it mimics the movement of aquatic organisms. The undulating propulsion system has numerous advantages over the rotary impeller and is becoming more popular in underwater robotics. The analysis of an artificial seal’s propulsion system with two tail fins is described here. The contrast between the previous undulating propulsion system and the new one is detailed using mathematical analysis and experimental data. The experimental comparison was carried out on a laboratory test stand equipped with specialist sensor equipment to determine the energy efficiency of various types of propulsion systems. Due to a patent procedure, the innovative propulsion system presented in this work has never been published previously. The fins have extra joints, which is the subject of patent claims. The extra joint is intended to improve energy efficiency and reduce fatigue wear on the fins.

Human detection from Unmanned Aerial Vehicles (UAV) is gaining popularity in the field of disaster management, crowd counting, people monitoring. Real time human detection from UAV is a challenging task, because of many constraints involved. This study proposes a system for real time detection of humans on videos captured from UAVs addressing three of these constraints namely, flying height, computation time and scale of viewing. The proposed method integrated an android application with a binary classifier based on Haar-features to automatically detect human / non-human class from UAV images. The video frames were parsed and detected humans from image frames were geo-localized and visualized on Google Earth. The performance was evaluated for geo-localization accuracy, computation time and detection accuracy, considering human coverage – pixel size relationship for various heights and scale factor. Based on flying height - human size relationship and tradeoff between detection accuracy vs computation time, the study came up with optimal parameters for OpenCV’s cv2.cascadeClassifier. detectMultiScale function. This paper establishes a strong ground for further research relating to real time human detection from UAV.

UAV network operation enables gathering and fusion from disparate information sources for flight control in both manned and unmanned platforms. In this investigation, a novel procedure for detecting runways and horizons as well as enhancing surrounding terrain is introduced based on fusion of enhanced vision system (EVS) and synthetic vision system (SVS) images. EVS and SVS image fusion has yet to be implemented real-world situations due to signal misalignment. We address this through a registration step to align the EVS and SVS images. Four fusion rules combining discrete wavelet transform (DWT) sub-bands are formulated, implemented and evaluated. The resulting procedure is tested on real EVS-SVS image pairs and pairs containing simulated turbulence. Evaluations reveal that runways and horizons can be detected accurately even in poor visibility. Furthermore, it is demonstrated that different aspects of the EVS and SVS images can be emphasized by using different DWT fusion rules. The procedure is autonomous throughout landing, irrespective of weather. We believe the fusion architecture developed holds promise for incorporation into head-up displays (HUDs) and UAV remote displays to assist pilots landing aircraft in poor lighting and varying weather. The algorithm also provided a basis rule selection in other signal fusion applications.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

Drone imagery has the potential to enrich urban planning and preservation, especially where it converges with the growing creation and use of 3D models. The authors have conducted a systematic literature review of articles published between 2002 and 2022, drawing from reputable academic repositories including Science Direct, Web of Science, and China National Knowledge Infrastructure (CNKI), to identify current gaps in existing research in the application of UAVs to the creation of 3D models in urban planning and preservation. Findings indicate five research shortcomings: limited participation of planning experts, research focus imbalance, lack of usage for special scenarios, lack of integration with smart city planning, and limited interdisciplinary collaboration. The study also acknowledges current limitations with UAV applications and discusses possible countermeasures as well as future prospects.

Microturbines can be used not only in models and education but also to propel UAVs. However, their wider adoption is limited by their relatively low efficiency and durability. Validated simulation models are required to monitor their performance, improve their lifetime, and design engine control systems. This study aims at developing a numerical model of a micro gas turbine for prediction and prognostics of engine performance. To build a reliable zero-dimensional model, the available compressor and turbine maps were scaled to the available test bench data with the least squares method, to meet the performance of the engine achieved during bench and flight tests. A steady-state aeroengine model was implemented in GSP and compared with experimental operating points. The selected flight data was then used as input for the transient engine model. The exhaust gas temperature (EGT) and fuel flow were chosen as the two key parameters to validate the model, comparing the numerical predicted values with the experimental ones. The observed difference between the model and the flight data was lower than 3% for both EGT and fuel flow.

BACKGROUND: Manufacturing costs, along with operational performance, are among the major factors determining the selection of the propulsion system for unmanned aerial vehicles (UAVs), especially for aerial targets and cruise missiles. OBJECTIVES: In this paper, the design requirements and operating parameters of small turbofan engines for single-use and reusable UAVs are analysed to introduce alternative materials and technologies for manufacturing their compressor blades, such as sintered titanium, a new generation of aluminium and an alloy based on titanium aluminides. METHODS: To assess the influence of severe plastic deformation (SPD) on the hardening efficiency of the proposed materials, the alloys in the coarse-grained and submicrocrystalline states were studied. Changes in physical and mechanical properties of materials were taken into account. The thermodynamic analysis of the compressor was performed in a finite element analysis system (ANSYS) to determine the impact of gas pressure and temperature on the aerodynamic surfaces of compressor blades of all stages. RESULTS: Based on thermal and structural analysis, the stress and temperature maps on compressor blades and vanes were obtained, taking into account the physical and mechanical properties of advanced materials and technologies of their processing. The safety factors of the components were established based on the assessment of their stress-strength reliability. Thanks to nomograms, the possibility of using the new materials and the technologies was confirmed in view of the permissible operating temperature and safety factors of blades. CONCLUSIONS: The proposed alternative materials and production technologies for the compressor blades and vanes meet the design requirements of the turbofan at lower manufacturing costs.

In scenarios such as natural disasters and military strike, it is common for unmanned aerial vehicles (UAVs) to form groups to execute reconnaissance and surveillance. To ensure the effectiveness of UAV communications, repeated resource acquisition issues and transmission mechanism design need to be addressed urgently. In this paper, we build an information interaction scenario in a Flying Ad-hoc network (FANET). The data transmission problem with the goal of throughput maximization is modeled as a coalition game framework. Then, a novel mechanism of coalition selection and data transmission based on group-buying is investigated. Since large-scale UAVs will generate high transmission overhead due to the overlapping resource requirements, we propose a resource allocation optimization method based on distributed data content. Comparing existing works, a data transmission and coalition formation mechanism is designed. Then the system model is classified into graph game and coalition formation game. Through the design of the utility function, we prove that both games have stable solutions. We also prove the convergence of the proposed approach with coalition order and Pareto order. Binary log-linear learning based coalition selection algorithm (BLL-CSA) is proposed to explore the stable coalition partition of system model. Simulation results show that the proposed data transmission and coalition formation mechanism can achieve higher data throughput than the other contrast algorithms.

With Unmanned Aerial Vehicles (UAV), a swift response to urgent needs like search \& rescue missions or medical deliveries can be realized. Simultaneously, the legislator is establishing so-called geographical zones, which restrict UAV operations to mitigate the air and ground risk to third parties. These geographical zones serve a particular safety interest, but they may also hinder the efficient usage of UAVs on time-critical missions with a range-limiting battery capacity. In this study, we address a facility location problem for up to two UAV hangars with a robust optimization model considering demand hotspots, geographical zones as restricted areas, a standard mission to satisfy battery capacity constraints, and the impact of wind scenarios. To this end, water rescue missions are used exemplary, for which positive and negative location factors for UAV hangars and areas of increased drowning risk as demand points are derived from open-source georeferenced data. Optimal UAV mission trajectories are computed with an A* algorithm considering five different restriction scenarios. As this pathfinding is very time-consuming, binary occupancy grids and image processing algorithms accelerate the computation by identifying either entirely inaccessible or restriction-free connections beforehand. For the optimal UAV hangar locations, we maximize accessibility while minimizing the service time to the hotspots, resulting in a decrease from the average service time of 570.4 s for all facility candidates to 351.1 s for one and 287.2 s for two optimal UAV hangar locations.

This manuscript explores unmanned aerial vehicle DC motor control performance efficacy of deterministic artificial intelligence in comparison to model-following adaptation, particularly a direct self-tuner with filtering. The deterministic artificial intelligence model made use of self-awareness statements to overcome error in response to permutations of the multi-duty cycle square wave that served as the system input. It can be seen that (despite equivalently powerful estimation techniques) deterministic artificial intelligence provided far superior results: a reduction in peak initial transient error of 55%, and a mean error reduction over 81% with over 65% reduction in error standard deviation compared to a state-of-the-art nonlinear adaptive control method. Deterministic artificial intelligence also was able to very closely track at the switching of the input control, while the benchmark nonlinear adaptive control failed to respond as quickly at these points.

Object of this work is the design and the simulation of a hybrid UAV with VTOL capabilities that has been designed for landing on naval moving platforms. The work is focused on the innovative propulsion layout adopted on the UAV. Authors discuss how adopted low level control strategies can exploit the innovative features of the proposed system assuring a good rejection of transversal wind disturbances. Particular attention is dedicated to low level modelling and control of the system emphasizing how choices regarding low level actuation and control should improve performances and robustness of the system.

Detecting, tracking, and classifying unmanned aerial vehicles (UAVs) in a swarm presents significant challenges due to their small and diverse radar cross-sections, multiple flight altitudes, velocities, and close trajectories. To overcome these challenges, adjustments of the radar parameters and/or position of the radar (for airborne platforms) are often required during runtime. The runtime adjustments help to overcome the anomalies in the detection, tracking, and classification of UAVs. The runtime adjustments are performed either manually or through fixed algorithms, each of which can have its limitations for complex and dynamic scenarios. In this work, we propose the use of multi-agent reinforcement learning (RL) to carry out the runtime adjustment of the radar parameters and position of the radar platform. The radar used in our work is a multibeam multifunction phased array radar (MMPAR) placed onboard UAVs. The simulations show the cognitive adjustment of the MMPAR parameters and position of the airborne platform using RL helps to overcome anomalies in the detection, tracking, and classification of UAVs in a swarm. A comparison with other artificial intelligence (AI) algorithms shows that RL performs better due to runtime learning of the environment through rewards.

This work is part of an ongoing research project to develop an unmanned flying social robot to monitor dependants at home in order to detect the person’s state and bring the necessary assistance. In this sense, this paper focuses on the description of a virtual reality (VR) simulation platform for the monitoring process of an avatar in a virtual home by a rotatory-wing autonomous unmanned aerial vehicle (UAV). This platform is based on a distributed architecture composed of three modules communicated through the Message Queue Telemetry Transport (MQTT) protocol: the UAV Simulator implemented in MATLAB/Simulink, the VR Visualiser developed in Unity, and the new emotion recognition (ER) System developed in Python. Using a face detection algorithm and a convolutional neural network (CNN), the ER System is able to detect the person’s face in the image captured by the UAV’s on-board camera and classify the emotion among seven possible ones (surprise, fear, happiness, sadness, disgust, anger or neutral expression). The experimental results demonstrate the correct integration of this new computer vision module within the VR platform, as well as the good performance of the designed CNN, with around 85% in the F1-score, a mean of the precision and recall of the model. The developed emotion detection system can be used in the future implementation of the assistance UAV that monitors dependent people in a real environment, since the methodology used is valid for images of real people.

Structure from Motion with Multi-View Stereo photogrammetry (SfM) is increasingly utilised in geoscience investigations as a cost-effective method of acquiring high resolution (sub-meter) topographic data, but has not been thoroughly tested in gullied savanna systems. The aim of this study was to test the accuracy of topographic models derived from aerial (via an Unmanned Aerial Vehicle, ‘UAV’) and ground-based (via a handheld digital camera, ‘Ground’) SfM in modelling a hillslope gully system in dry-tropical savanna, and to assess the strengths and limitations of the approach at different scales. A UAV survey covered an entire hillslope gully system (0.715 km²), whereas a Ground survey covered a single gully within the broader system (650 m²). SfM topographic models, including Digital Surface Models (DSM) and dense point clouds, were compared against RTK-GPS point data and a pre-existing airborne LiDAR Digital Elevation Model (DEM). Results indicate UAV SfM can deliver topographic models with a resolution and accuracy suitable to define gully systems at a hillslope scale (e.g., 0.1 m resolution with ~ 0.5 – 1.3 m elevation error), while ground-based SfM is more capable of quantifying gully morphology (e.g., 0.01 m resolution with ~ 0.1 m elevation error). Key strengths of SfM for these applications include: the production of high resolution 3D topographic models and ortho-photo mosaics, low survey instrument costs (< $AUD 3,000); and rapid survey time (4 and 2 hours for UAV and Ground survey respectively). Current limitations of SfM include: difficulties in reconstructing vegetated surfaces; uncertainty as to optimal survey and processing designs; and high computational demands. Overall, this study has demonstrated great potential for SfM to be used as a cost-effective tool to aid in the mapping, modelling and management of hillslope gully systems at different scales, in tropical savanna landscapes and elsewhere.

TThe following three objectives were tested in this study: (1) investigate the utility of low-altitude remote sensing using UAS technology to compare the effects of different N application systems in rice production; (2) use spatial extrapolation to scale up plot-level generated to farmer field rice yield data based on crop spectral signatures, and (3) predict and map out rice productivity as a function of N placement systems. Images were captured on a UAV platform at midseason of the rice crop. Orthomosaics were developed for selected fields in rice-producing zones. Grain yields were assessed from low, medium, and high crop health plots delineated based on NDVI values. On the plot scale, UDP outyielded non-UDP by 0.84%. Individual plot yield data were scaled up to the farmer field level through Jenks natural breaks classification and es-tablishing an empirical relationship between OSAVI and plot yields. Assessment of the scaled-up field levelfield-level data also confirmed the superiority of UDP N man-agement over the non-UDP systems in promoting rice yields. Scaling up plot scale da-ta to whole field levels also facilitated generating and mapping expected yield maps for individual farmer fields in the three zones studied. This study has established a tangible simple but tangible protocol protocol for predicting and mapping rice yields in small-scale farmer fields using UAS data.

In recent years, pedestrian re-identification has gained a lot of interest due to its importance for many purposes such as security and safety. Many types of solutions have been proposed to solve this problem, where the majority are based on a features extraction such Convolution Neural Networks (CNNs). These approaches assume that only the identities that are in the training data can be recognized. The pedestrians in the training data are called In distribution (ID). However, in real world scenarios, new pedestrians and objects can appear in the scene and the model should detect them as Out Of Distribution (OOD). In our previous study , we proposed a pedestrian re-identification based on von-Mises Fisher (vMF) distribution. Each identity is embedded in the unit sphere as a compact vMF distribution far from other identities distributions. The embedding is done through a base CNN. Recently, proposed a framework called Virtual Outlier Synthetic (VOS), that detects OOD based on synthesising virtual outlier in the embedding space in an online manner. Their approach assumes that the samples from the same object maps to a compact space. This assumption aligns with the vMF based approach. Therefore, in this paper, we revisited the vMF approach and merged with VOS in order to detect OOD data points. We present our approach to merge both frameworks. We conducted several experiments to evaluate our proposed framework. Results showed that our framework was able to detect new pedestrian that do not exist in the training data in the inference phase. It also slightly helped to improve the re-identification performance.

The location and number data of individual fruit trees are critical for planting area investigation, fruit yield prediction, and smart orchard management and planning. These data are conventionally obtained through manual investigation and statistics with time-consuming and laborious effort. Object detection models in deep learning used widely in computer vision could provide an opportunity for accurate detection of individual fruit trees, which is essential for rapidly obtaining the data and reducing human operations errors. This study proposes an approach to detecting individual fruit trees and mapping their spatial distribution by integrating deep learning with unmanned aerial vehicle (UAV) remote sensing. UAV remote sensing collected high-resolution true-color images of fruit trees in the experimental pomelo tree orchards in Meizhou city, South China. An image dataset of deep learning samples of individual pomelo trees (IPTs) was constructed through visual interpretation and field investigation based on the fruit tree images captured by UAV remote sensing. Four different scales of YOLOv5 (YOLOv5s, YOLOv5m, YOLOv5l, and YOLOv5x) for object detection were selected to train, validate, and test on the image dataset of pomelo trees. The results show that the average precision (AP@0.5) of the four YOLOv5 models for validation reach 87.8%, 88.5%, 89.1%, and 90.7%, respectively. The larger the model scale, the higher the average accuracy of the detection result of validation. It suggests that YOLOv5x is a preferred high-accuracy model among the YOLOv5 family and is suitable to realize the detection of IPTs. The number of the IPTs in the study area was counted using YOLOv5x, and their spatial distribution map was made using the non-maximum suppression method and ArcGIS software. This study will provide primary data and technical support for smart orchard management in Meizhou city and other fruit-producing areas.

This study introduces a remote sensing application using satellite imagery to survey a network-scale aggregate stockpile inventory. First, a real scale aggregate quarry site was surveyed using a small Unmanned Aerial Vehicle (sUAV) to produce digital terrain models that enabled analysis of aggregate pile geometry. Second, a lab experiment was designed and performed to validate the applicability of close-range Structure from Motion (SfM) photogrammetry for measuring aggregate piles' physical properties such as volume and density. The other part of the lab experiment delved into direct measurement of aggregate density under varying compaction efforts. These experimental results, in conjunction with some simplifying assumptions, enabled the calculation of aggregate stockpile volumes and estimated weights from satellite imagery. We estimated that an inventory of 4.4 and 1.1 million metric tons of crushed aggregates and Reclaimed Asphalt Pavement (RAP), respectively, stockpiled in Washington State for asphalt production in 2017. The merit of producing such database was further showcased in an example on the economic and environmental impacts of material transportation. We approximated that hauling aggregates from quarry plants to construction sites within Washington State incurs a cost of about $50 thousand to over $4 million, consumes about 0.25 to 20 TJ of energy, and emits 20 to over 1,500 tons of CO₂-eq per asphalt plant annually.

Forest canopy gaps are important for the ecosystem dynamics. Depending on tree species, small canopy openings might be also associated to intra-crown porosity and to space between crowns. Yet, little is known on the relationships between the fine-scaled pattern of canopy openings and biodiversity features. This research explored the possibility of i)- mapping forest canopy gaps from a very high resolution orthomosaic (10 cm), processed from a versatile imaging platform such as unmanned aerial vehicles (UAV), ii)- to derive patch metrics that can be tested as covariates of variables of interest for forest biodiversity monitoring. This is attempted in a test area of 240 ha covered by temperate deciduous forest types in Central Italy and containing 50 forest inventory plots of about 530 m². Correlation and linear regression techniques were used to explore relationships between patch metrics and understorey (density, development and species diversity) or forest habitat biodiversity variables (density of micro-habitat bearing trees, vertical species profile, tree species diversity). The results revealed that small openings in the canopy cover (75% smaller than 7 m²) can be faithfully extracted from UAV RGB imagery, using the red band and contrast split segmentation. Highest correlations were observed in the mixed forest (beech and turkey oak), while beech forest had the poorest ones and turkey oak forest displayed intermediate results. Moderate to strong linear relationships were found between gap metrics and understorey variables in mixed forest type, with adjusted R² from linear regression ranging from 0.52 to 0.87. Equally good results, in the same forest types, were observed for forest habitat biodiversity variables (0.52<adjusted R²<0.79) with highest values found for density of trees with microhabitats and vertical species profile. In conclusion, this research highlights that UAV remote sensing can potentially provide covariate surfaces of variables of interest for forest biodiversity monitoring, conventionally collected in forest inventory plots. By integrating the two sources of data, these variables can be mapped over small forest areas with satisfactory levels of accuracy, at a much higher spatial resolution than would be possible by field-based forest inventory solely.

Dams are a critical infrastructure system for many communities, but they are also one of the most challenging to inspect. Dams are typically very large and complex structures, and the result is that inspections are often time-intensive and require expensive, specialized equipment and training to provide inspectors with comprehensive access to the structure. The scale and nature of dam inspections also introduces additional safety risks to the inspectors. Unmanned aerial vehicles (UAV) have the potential to address many of these challenges, particularly when used as a data acquisition platform for photogrammetric three-dimensional (3D) reconstruction and analysis, though the nature of both UAV and modern photogrammetric methods necessitates careful planning and coordination for integration. This paper presents a case study on one such integration at the Brighton Dam, a large-scale concrete gravity dam in Maryland, USA. A combination of multiple UAV platforms and multi-scale photogrammetry was used to create two comprehensive and high-resolution 3D point clouds of the dam and surrounding environment at intervals. These models were then assessed for their overall quality, as well as their ability to resolve flaws and defects that were artificially applied to the structure between inspection intervals. The results indicate that the integrated process is capable of generating models that accurately render a variety of defect types with sub-millimeter accuracy. Recommendations for mission planning and imaging specifications are provided as well.

In recent years, the unmanned aerial vehicle (UAV) synthetic aperture radar (SAR) has become a highly sought-after topic for its wide applications in the field of target recognition, detection, and tracking. However, SAR automatic target recognition (ATR) models based on deep neural networks (DNN) are suffering from adversarial examples. Generally, non-cooperators rarely disclose any information about SAR-ATR models, making adversarial attacks challenging. In this situation, we propose Transferable Adversarial Network (TAN) to attack these models with highly transferable adversarial examples. The proposed method improves the transferability via a two-player game, in which we simultaneously train two encoder-decoder models: a generator that crafts malicious samples through a one-step forward mapping from original data, and an attenuator that weakens the effectiveness of malicious samples by capturing the most harmful deformations. In particular, compared to traditional iterative methods, our approach is able to one-step map original samples to adversarial examples, thus enabling real-time attacks. Experimental results indicate that the proposed approach achieves state-of-the-art transferability with acceptable adversarial perturbations and minimum time costs compared to existing attack methods, i.e., it excellently realizes real-time transferable adversarial attacks.

This manuscript compares deterministic artificial intelligence to model following control applied to DC motor control, including evaluation of the threshold computation rate to let unmanned underwater vehicles correctly follow the challenging discontinuous square wave command signal. The approaches presented in the main text are validated in MATLAB®, where the motor process is discretized at multiple step sizes, which is inversely proportional to the computation rate. The performance is evaluated by the error mean and standard deviation. With a large step size, discrete deterministic artificial intelligence shows a larger error mean than the model-following self-turning regulator approach (benchmark selection). However, the performance gets optimized with the step size decreased. The error mean is close to the continuous deterministic artificial intelligence when the step size is reduced to 0.2 seconds, which means that the computation rate and the sampling period restrict discrete deterministic artificial intelligence. In that case, the continuous deterministic artificial intelligence is the most feasible and reliable selection for future applications on unmanned underwater vehicles since it is superior to all the approaches with multiple computation rates.

This study examines the activities conducted at the archaeological site of Aptera in Crete, Greece. The research was part of the DIACHRONIC LANDSCAPES International Design Workshop, organized by the CAM (Center for Mediterranean Architecture), TUC (Technological University of Crete School of Architecture), and UNIFE (University of Ferrara Department of Architecture). This article outlines the methods used for data acquisition and processing on a territorial scale, which generated digital outputs necessary for the analysis and design phases of the workshop, as well as for further examination of the results. The collected data, obtained through low-cost aerial photogrammetric surveying and GNSS terrestrial coordinate detection, were integrated in a Structure from Motion workflow that led to the creation and exportation of various digital outputs, such as point clouds, DTM, DSM, orthophotos, and contour lines. An accuracy analysis was performed to evaluate the effectiveness and efficiency of the digital models compared to the implemented surveying strategies, including the Ground Control Point and Quality Check Point marker positioning strategy. The resulting digital models proved to be valuable assets for analysis and design within the workshop and provided insightful prospects for future research and territorial-scale projects.