In this work, an enzymatic sensor, based on a bionanocomposite film consisting of a polyelectrolyte complex (PEC) [Chitosan/kappa-carrageenan] doped with gold nanoparticles (AuNPs) encapsulating glucose oxidase (GOD) deposited on a gold electrode (Au) for glucose sensing, is described. Using the electrocatalytic synergy of AuNPs and GOD as a model of enzyme, the variation of the current (µA) as a function of the log of the glucose concentration (log [glucose]), shows 3 times higher sensitivity for the modified electrode (283.9) compared to that of the PEC/GOD modified electrode (93.7), with a detection limit of about 5 µM and a linearity range between 10µM and 7mM. The response of the PEC/AuNPs/GOD based biosensor also presents good reproducibility, stability and negligible interfering effects from ascorbic acid, uric acid, urea and creatinine. The applicability of the PEC/AuNPs/GOD based biosensor was tested in glucose-spiked saliva samples and acceptable recovery rates were obtained.

Plasmonic gold nanorods play important roles in nowadays state-of-the-art plasmonic sensing techniques. Most of the previous studies and applications focused on gold nanorods with relatively small aspect ratios, where the plasmon wavelengths are smaller than 900 nm. Gold nanorods with large aspect ratios are predicted to exhibit high refractive-index sensitivity (Langmir 2008, 24, 5233–5237.), which therefore should be promising for developing of high-performance plasmonic chemical- and bio-sensors. In this study, we developed gold nanorods with aspect ratios over 7.9, which exhibit plasmon resonances around 1064 nm. The refractive index (RI) sensitivity of these nanorods have been evaluated by varying their dielectric environment, whereby a sensitivity as high as 473 nm/RIU can be obtained. Furthermore, we have demonstrated the large-aspect-ratio nanorods as efficient substrate for surface enhanced Raman spectroscopy (SERS), where an enhancement factor (EF) as high as 9.47×10⁸ was measured using 4-methylbenzenethiol (4-MBT) as probe molecule. Finally, a type of flexible SERS substrate is developed by conjugating the gold nanorods with the polystyrene (PS) polymer. The results obtained in our study can benefit the development of plasmonic sensing techniques utilized in the near-infrared spectral region.

Although there are extensive literature reports on the use of gold nanoparticle (AuNP) based homogeneous assays for detection of biomolecules, very few experimental description and procedures involving their preparation are described. In this study, AuNPs conjugated to Bovine Serum Albumin or Envelope protein from Dengue II were developed as a homogeneous immunoassay for antibody detection. We report here optimization of key parameters to prepare an immunoassay like conjugation protein concentration, centrifugation time, electrolyte addition and assay temperature. We determined that saturating protein concentrations improved AuNPs surface coverage and uniformity of the assay and addition of sodium chloride improved sensitivity of the antibody detection method and assay stability. Furthermore, we showed that dynamic light scattering can be used to monitor changes in gold nanoparticles in the preparation and detection steps. Additionally, numerical simulations of the plasmonic optical response of AuNPs were carried out to scan for size-dependent response of the AuNPs. The AuNPs homogeneous immunoassay developed was further used in the detection of antibodies in vitro to detect Dengue virus infection.

Artisanal and small-scale gold mining (ASGM) has been an important source of income for communities in the Madre de Dios River Basin in Peru for hundreds of years. However, in recent decades, the scale of ASGM activities in the region has increased dramatically, and exposures to a variety of occupational and environmental hazards related to ASGM, including mercury, are becoming more widespread. The aims of our study were to: (1) examine patterns in the total hair mercury level of human participants in several communities in the region and compare these results to the 2.2 µg/g total hair mercury level equivalent to the World Health Organization (WHO) Expert Committee of Food Additives (JECFA)’s Provisional Tolerable Weekly Intake (PTWI); and (2), to measure the mercury levels of paco (Piaractus brachypomus) fish raised in local aquaculture ponds, in order to compare these levels to the EPA Fish Tissue Residue Criterion of 0.3 µg Hg/g fish (wet weight). We collected hair samples from 80 participants in four communities (one control and three where ASGM activities occurred) in the region, and collected 111 samples from fish raised in 24 local aquaculture farms. We then analyzed the samples for total mercury. Total mercury levels in hair were statistically significantly higher in the mining communities than in the control community, and increased with increasing distance away from the Madre de Dios headwaters (as the crow flies), did not differ by sex, and frequently exceeded the reference level. Regression analyses indicated that higher hair mercury levels were associated with residence in ASGM communities. The analysis of paco fish samples found no samples that exceeded the EPA tissue residue criterion. Collectively, these results align with other recent studies showing that ASGM activities are associated with elevated human mercury exposure. The fish farmed through the relatively new process of aquaculture in ASGM areas appeared to have little potential to contribute to human mercury exposure. More research is needed on human health risks associated with ASGM to discern occupational, residential, and nutritional exposure, especially through tracking temporal changes in mercury levels as fish ponds age, and assessing levels in different farmed fish species. Additionally, research is needed to definitively determine that elevated mercury levels in humans and fish result from the elemental mercury from mining, rather than from a different source, such as the mercury released from soil erosion during deforestation events from mining or other activities.

Gold occurrence Maljavr, located in amphibolite metamorphosed rocks in the Uragubsky greenstone belt, is the first gold prospect connected with conglomerates of Archean age, found in the Fennoscandian Shield. Gold mineralization is controlled by a series of lenses of altered rocks in biotite gneiss-metaconglomerate. The age of zircon from biotite gneiss in the zone of alteration is 2665±22 Ma, this is considered as the time of alteration processes. Biotite gneiss and altered rocks were later intruded by tourmaline granite pegmatite at 2508±7Ga, the pegmatite caused recrystallization of sulfide minerals in the altered rocks. Visible gold in association with bismuth minerals native bismuth, ehrigite (the second finding in the world), maldonite, bismuthinite, joseite-B, hedleyite was found exceptionally in polymineral inclusions in recrystallized arsenopyrite and löllingite. The age of pegmatite 2508±7Ma we regard as the time of formation of gold-bismuth mineralization. Geological position of the Maljavr occurrence, the linkage of gold mineralization with pegmatite, geochemical association Au-As-Se-Te-Bi in the mineralized rocks – all these characteristics correspond to intrusion-related gold deposits. Biotite gneiss-metaconglomerate, hosting the mineralized altered rocks, was the probable primary source of arsenic and gold for mineralization.

This study employs traditional OLS (ordinary least squares) regression analysis to investigate the influence of various external factors on Bitcoin price fluctuations from January 2014 to March 2023 using a multidimensional approach. We use factors from the traditional financial market, such as economic policy uncertainty (EPU), oil prices, the NASDAQ index, and gold prices, to identify factors contributing to Bitcoin volatility. Considering the unique situation in the Bitcoin market, that is, 24-hour trading and the short duration of its existence, we incorporate the broadest possible data range to achieve alignment between Bitcoin data and other datasets. The findings of the statistical analysis indicate that EPU and the NASDAQ index promote positive fluctuations in Bitcoin volatility, whereas gold prices act as a dampener. However, we find no empirical support for the influence of energy prices on Bitcoin volatility. These results suggest that Bitcoin should not be underestimated; all stakeholders should treat the issue of Bitcoin volatility seriously, including governments, who should actively regulate the Bitcoin market, and investors, who should recognize the dangers of this volatility, making rational decisions based on individual circumstances and employing flexible trading strategies.

Marine sediment sample was collected and the total aerobic population was counted and probiotic Bacillus cereus was isolated. Then it was mixed with formulated feed by spraying, while control diet was purchased from a local aquarium. 30 days of feeding experiment was conducted. Carassius auratus fishes were randomly divided into two experimental groups in rectangular tanks. The first group served as a control in which fishes were fed with commercial feed. The second group of fish were fed with probiotic incorporated feed. After 40 days, their survival and growth performance were detected. Bacillus cereus incorporated feed significantly yielded higher survival rate of the fish compared to control. Food conversion ratio (FCR) was significantly lower than the control group. The main aim of this work is to investigate the effect of a marine probiotic bacteria, Bacillus cereus on the survival and growth performance of gold fish Carassius auratus.

Due to their well-defined plasmonic properties, gold nanorods (GNRs) can be fabricated with optimal light absorption in the near-infrared region of the electromagnetic spectrum, which make them suitable for cancer-related theranostic applications. However, their controversial safety profile, as a result of surfactant stabilization during synthesis, limits their clinical translation. We report a facile method to improve GNR biocompatibility through the presence of sodium dodecyl sulfate (SDS). GNRs (120 x 40 nm) were synthesized through a seed-mediated approach, using cetyltrimethylammonium bromide (CTAB) as a cationic surfactant to direct the growth of nanorods and stabilize the particles. Post-synthesis, SDS was used as an exchange ligand to modify the net surface charge of the particles from positive to negative while maintaining rod stability in an aqueous environment. GNR cytotoxic effects, as well as the mechanisms of their cellular uptake, were examined in two different cancer cell lines, Lewis lung carcinoma (LLC) and HeLa cells. We not only found a significant dose-dependent effect of GNR treatment on cell viability but also a time-dependent effect of GNR surfactant charge on cytotoxicity over the two cell lines. Our results promote a better understanding of how we can mediate the undesired consequences of GNR synthesis byproducts when exposed to a living organism, which so far has limited GNR use in cancer theranostics.

The requirements for using noncyanide imitation gold plating as decorative electroplating are increasing; thus, continuously improving the quality of the coating of the imitation gold plating and optimizing the coating process have become the current priority. In this work, hydroxyethylidene diphosphonic acid (HEDP) was used as the main complexing agent, CuSO4·5H2O, ZnSO4·7H2O and NaSnO3·3H2O were the main salts, and NaOH and anhydrous sodium carbonate were used as the buffers to prepare the electroplating solution. Using sodium citrate (SC), sodium potassium tartrate (SS), sodium gluconate (SG), and glycerol (Gl) as four additives, the effects of the number of carboxyl groups on the properties of a Cu-Zn-Sn alloy coating were compared. The electrochemical analysis showed that Cu-Zn-Sn alloy codeposition occurred at -0.50 V vs. Hg|HgO. The scanning electron microscopy (SEM) results showed that the particle size of the coatings obtained with carboxyl-containing additives was more uniform than that obtained with the electroplating solution without additives. The X-ray fluorescence spectrometry (XRF) analysis revealed that the composition of the Cu-Zn-Sn alloy coating obtained by using SC as an additive in the electroplating solution was 89.75 wt% Cu, 9.61 wt% Zn, and 0.64 wt% Sn, and the color of the coating was golden yellow. The X-ray diffraction (XRD) pattern showed that the coating was a mixture of Cu, Cu5Zn8, CuSn, Cu6Sn5, and CuZn phases. The analysis of the electroplating solution by UV, IR and NMR spectroscopy methods indicates that the additives improve the coating by affecting the complexation reaction of metal ions. These results can provide technical and theoretical guidance for developing Cu-Zn-Sn ternary alloy electrodeposition technology with the new cyanide-free HEDP alkaline electroplating system.

Techniques of stripping voltammetry (SV) determination of silver and gold in pyrites and carbonaceous matter were developed. The problem of quantitative transfer of the sample into the solution was solved. For this purpose, the ore matrix of carbonaceous shales was decomposed by mineral acids in autoclaves at high pressures. The element to be determined from the sample matrix was separated by extraction. Ag(I) ions from the solutions were extracted in the form of dithizonate complex in CCl₄. Au(III) ions were extracted by diethyl ether. The extracts were decomposed thermally. The dry residue was dissolved in the background electrolyte, and the element was determined by the SV method. The graphite electrode (GE) impregnated with polyethylene was used as a working electrode in SV–determination of silver. SV–determination of gold was carried out using GE modified by bismuth. The limits of detection (LOD) of Ag(I) and Au(III) contents were equal to 0.016 mg L^-1 and 0.0086 mg L^-1, respectively. The results of SV-determination of gold and silver in standard samples, pyrites and carbonaceous shales were presented. The silver content in the pyrite was 13.6 g t^-1, in carbon shale—0.34 g t^-1. The concentration of gold in the pyrite ore zone "Kirovsko–Kryklinskaya" was 1.15 g t^-1; in carbonaceous shales—2.66 g t^-1. The obtained data were consistent with the data of atomic emission spectroscopy (AES) and inductively coupled plasma mass spectrometry (ICP—MS). The error of determination of elements by stripping voltammetry was calculated when determining the silver content of 10...6 g t^-1 in pyrite and carbonaceous material, which was less than 12%, and when determining the gold content of 1...3 g t^{- 1} in pyrite and carbonaceous matter, which was less than 23%.

XPS and ARXPS characterization of surface layers resulting from the functionalization of polymers such as PVC modified with MPTMS and APTES is challenging due to the signals overlap, deriving both from the substrate and the functionalized layers. In this work, a freshly cleaved, ideally flat gold surface was used as carbon-free model substrate functionalized with MPTMS and subsequently grafted with APTES. Avoiding the overlap of signals from carbon atoms present in the substrate, the signals in the C1s, O1s, Si2p, S2p and N1s high-resolution spectra could be assigned to the MPTMS / APTES functionalized layer only and the curve fitting parameters could be determined. Quantitative analysis was in very good agreement with the expected stoichiometry of the functionalized layer, confirming the adopted curve fitting procedure. In addition, it was found that one molecule of APTES grafted two MPTMS via silane groups. ARXPS allowed determining the thickness of the functionalized layers: MPTMS thickness was found to be 0.5 (0.2) nm, MPTMS + APTES thickness 1.0 (0.2) nm in good agreement with Avogadro model calculations. This approach can be considered a powerful tool for characterising functionalized surfaces of more complex systems by XPS.

This comprehensive review delves into gold market business management, covering historical perspectives, market dynamics, mining models, investment strategies, technology, regulations, global trends, and sustainability. Starting with a historical overview, it traces the gold market's evolution and analyzes supply-demand dynamics, price fluctuations, and geopolitical influences. The article scrutinizes gold mining models, evaluating environmental and social responsibilities, and explores financial management strategies, emphasizing risk and gold's role in portfolios. Examining technology's role, it highlights innovations in exploration, mining, and processing for improved efficiency and sustainability. The regulatory landscape analysis encompasses compliance challenges, environmental regulations, and ethical considerations, emphasizing global impacts. Global market trends are explored, identifying potential opportunities and challenges, offering strategic insights. The review concludes by evaluating sustainability practices, emphasizing environmental conservation, community engagement, and ethical sourcing.

The goal of this study was to develop a rapid diagnostic kit for rheumatic disease and systemic lupus erythematosus (SLE) screening. A novel rapid vertical flow assay (VFA) was engineered and used to assay anti-nuclear (ANA) and anti-dsDNA (αDNA) autoantibodies from systemic lupus erythematosus (SLE) patients and healthy controls (HC). Observer scores and absolute signal intensities from the VFA were validated by ELISA. The rapid ten minute point of care VFA test engineered demonstrated a limit of detection of 0.5 IU/ml for ANA and αDNA autoantibodies in human plasma with inter-operator CV of 19% for ANA and 12% for αDNA. Storage stability was verified over a three-month period. When testing anti-dsDNA and ANA levels in 22 SLE and 18 HC serum samples, the duplex VFA revealed 95% sensitivity, 72% specificity and 84% accuracy in discriminating disease groups, comparable to the gold standard, ELISA. The rapid αDNA/ANA duplex VFA can potentially be used in primary care clinics for evaluating patients or at-risk subjects for rheumatic diseases and for planning follow-up testing. Given its low cost, ease and rapid turnaround, it can also be used to assess SLE prevalence estimates.

Orogenic antimony-gold deposits contribute significantly to the global antimony resource base. China's orogenic antimony-gold deposits are primarily in southern Tibet. Investigations indicate that antimony combines and migrates with sulfur hydroxides in ore-forming fluids. Previous research on fluid inclusions in orogenic antimony-gold ores with sedimentary rock accommodation revealed the presence of organic inclusions, including liquid hydrocarbons, alongside common components such as CO2, H2O, CH4, and NaCl. However, the impact of liquid hydrocarbons on antimony migration and mineralization is still de-batable. To investigate the transportability of antimony by liquid hydrocarbons in orogenic antimony ores, we selected n-dodecanethiol and n-dodecane as the subjects. We measured the solubility and occurrence form of antimony in these compounds at various temperatures and durations. The results indicate that after 5 and 10 days of reaction at 100 °C, the antimony concentrations in the n-dodecanethiol and n-dodecane groups were 67.44±7.62 ppm, 75.15±16.74 ppm, 1.40±1.02 ppm, and 3.02±3.09 ppm, respectively. At 150 °C for 5 and 10 days, the respective concentrations were 50.58±5.39 ppm, 77.26±45.20 ppm, 2.66±3.08 ppm, and 2.41±2.03 ppm. At 200 °C for 5 and 10 days, the corresponding concentrations were 339.76±71.94 ppm, 218.97±25.03 ppm and 6.53±7.17 ppm, 2.27±0.82 ppm (n=3). The measured solubility of antimony in the n-dodecanethiol group increased gradually with rising temperature. The solubility of antimony in the n-dodecane group was low and notably inferior to that observed in the n-dodecanethiol group. X-ray photoelectron spectroscopy (XPS) analysis demonstrated a distinct thiol (R-SH) peak at 163.31 eV and compound peaks of antimony reacting with thiols at 162.06 and 160.87 eV. This suggests that antimony predominantly forms complexes with thiols for migration. Our findings suggest that specific liquid hy-drocarbon components, predominantly thiols, can interact with antimony at metallogenic temperatures and persist in ore-forming fluids, facilitating migration and mineral enrichment. Earlier experimental studies on gold and crude oil have indicated that liquid hydrocarbons also play an essential role in the transportation and enrichment of gold during the formation of gold deposits, thus indicating that liquid hydrocarbons possess the considerable potential to act as an ore-forming fluid during orogenic antimony-gold deposit formation in southern Tibet.

The expedited development of drugs targeting gene products associated with insulin resistance holds the potential to enhance our comprehension of type 2 diabetes mellitus (T2DM). The virtual screening based on a three-dimensional (3D) protein structure has been expected as potential technique to accelerate a development of molecular target drugs. Among the targets implicated in insulin resistance, genetic characterization and protein function of Grb14 have been clarified without contradiction. The Grb14 gene displays notable variations in T2DM, and its gene product known to inhibit the function of the insulin receptor (IR) by directly binding to the tyrosine kinase domain. In the present study, a virtual screening, based on 3D structure of IR tyrosine kinase domain (IRβ) in complex with part of Grb14, was conducted to find compounds that can disrupt the complex formation between Grb14 and IRβ. First, ten compounds were selected from 154,118 compounds via hierarchical in silico structure-based drug screening, composed of grid docking-based and genetic algorithm-based programs. The experimental validations suggested that the one compound can affect blood glucose level. The molecular dynamics simulations and co-immunoprecipitation analysis showed that the compound did not completely suppress the protein–protein interaction between Grb14 and IR, though competitively bound to IR with the tyrosine kinase pseudosubstrate region in Grb14.

Syanyonja village in the gold district of Busia, South East of the Republic of Uganda contain geologically epigenetic gold quartz vein deposits in carbonate-altered mafic metavolcanic rocks, deposited as quartz reefs in mineralized shear zones. In supracrustal rocks, alluvial gold is obtained from weathered auriferous quartz veins, which are of late orogenic granitic activity. The Syanyonja gold deposits have long been subjected to artisanal and small-scale gold mining (ASGM) by the locals for livelihood. This study determined the amount of mercury discharged with tailings into Namukombe stream, a major water body in Syanyonja village and investigated the impacts of ASGM on the mining population and the environment. Quantitation of mercury discharged with tailings was done by mass balance method. Field survey at the mining sites was done followed by administration of questionnaires to 50 stampeders in the village. The study indicates that about 8% of mercury mixed with auriferous materials are lost in tailings, accounting for an annual mercury release of about 1.757 kg into the environment. Socio-demographic results indicate that the majority of the mining population (64%) are male and ASGM have left health and environmental footprints, which directly or indirectly affects the population. The most common health problems among miners are malaria (36%) and abdominal pain (20%). The standard of living of the miners are evidently low, and most mines are characterized by school dropouts, prostitutes and thieves. Mining sites have deplorably poor hygiene, with evident burning of amalgams to recover gold. ASGM have been accompanied by wanton mowing down of vegetation, land degradation as well as mercuric pollution of water, air, land and aquatic ecosystems. It is suggested that the Ugandan government should re-enforce committees to follow up on ASGM activities, train artisans on sustainable gold mining using borax, magnets, sluice boxes as well as take up farming actively as an alternative.

Protein immobilization for the functionalization of particles is used in various applications, including biosensors, lateral-flow immunoassays (LFIA), bead-based assays, and others. Common methods for the quantification of bound protein are measuring protein in the supernatant before and after coating and calculating the difference. This popular approach has the potential for a significant overestimation of the amount of immobilized protein since layers not directly bound to the surface (soft protein corona) are usually lost during washing and handling. Only the layer directly bound to the surface (hard corona) can be used in subsequent assays. A simplified amino acid analysis method based on acidic hydrolysis and RP-HPLC-FLD of tyrosine and phenylalanine (aromatic amino acid analysis, AAAA) is proposed to directly quantify protein bound to the surface of gold nano- and latex microparticles. The results are compared with indirect methods such as colorimetric protein assays, such as Bradford, bicinchoninic acid (BCA), as well as AAAA of the supernatant. For both particle types, these indirect quantification techniques show a protein overestimation of up to 1700% compared to the direct AAAA measurements. In addition, protein coating on latex particles was performed both passively through adsorption and covalently through EDC/sulfo-NHS chemistry. Our results showed no difference between the immobilization methodologies. This finding suggests that usual protein determination methods are no unambiguous proof of a covalent conjugation on particles or beads.

Gold nanoparticles (AuNPs) have been used in a broad range of applications conferring to bio-molecules diverse proprieties such as deliver, stabilization and reduction of adverse effects of drugs or plant ex-tracts. Polyphenolic compounds from Bacopa procumbens (BP) are able to modulate proliferation, adhesion, migration and cell differentiation, reducing artificial scratch area in fibroblast cultures and promoting wound healing in in vivo model. Here, chemically synthetized AuNPs conjugated with BP (AuNP-BP) were characterized by Uv-Vis, ATR-FTIR, DLS and zeta-potential. Results showed over-lapping FTIR spectra of polyphenolic compounds from B. procumbens capping the AuNPs, stable size by the DLS and zeta potential, AuNP-BP was 44.58 nm, the zeta-potential of AuNPs was -36.3±12.3 mV after conjugation with the BP; - (AuNP-BP), the zeta-potential was reduced to -18-2±7.02 mV. Enhancement of wound healing effect were evaluated by morphometric, histochemical and FTIR changes in rat wound excision model. Results showed that the nanoconjugation process reduced 100 folds BP concentrations to have the same wound healing effect of BP alone. Besides histological and FTIR spec-troscopy analyses, demonstrated that AuNP-BP treatment displayed better macroscopical performance; the reduction on inflammatory cells, and the increased synthesis and better organization of collagen fibers.

Dielectric spectroscopy (DS) is a promising cell screening method that can be used for diagnostic and drug discovery purposes. The primary challenge of using DS in physiological buffers is the electrode polarization (EP) that overwhelms the impedance signal within a large frequency range. These effects further amplify with miniaturization of the measurement electrodes. In this study, we present a microfluidic system and the associated equivalent circuit models for real-time measurements of cell membrane capacitance and cytoplasm resistance in physiological buffers with 10s increments. The current device captures several hundreds of biological cells in individual microwells through gravitational settling and measures the system’s impedance using microelectrodes covered with dendritic gold nanostructures. Using PC-3 cells (a highly metastatic prostate cancer cell line) suspended in cell growth media (CGM), we demonstrate stable measurements of cell membrane capacitance and cytoplasm resistance in the device for over 15 minutes. We also describe a consistent application of the equivalent circuit model, starting from the reference measurements used to determine the system parameters. The circuit model is tested using devices with varying dimensions, and the obtained cell parameters between different devices are nearly identical. Further analyses of the impedance data have shown that accurate cell membrane capacitance and cytoplasm resistance can be extracted using a limited number of measurements in the 5 MHz to 10 MHz range. This will potentially reduce the timescale required for real-time DS measurements below 1s. Overall the new microfluidic device can be used for dielectric characterization of biological cells in physiological buffers for various cell screening applications.

Biofouling is the unwanted adsorption of cells, proteins, or intracellular and extracellular bio-molecules that can spontaneously occur on the surface of metal nanocomplexes. It represents a major issue in bioinorganic chemistry because it leads to the creation of a protein corona, which can destabilize a colloidal solution and result in undesired macrophage-driven clearance, consequently causing failed delivery of a targeted drug-cargo. Hyaluronic acid (HA) is a bioactive, natural mucopolysaccharide with excellent antifouling properties, arising from its hydrophilic and polyanionic characteristics in physiological environments which prevent opsonization. In this study, hyaluronate-thiol (HA-SH) (MW 10 kDa) was used to surface-passivate gold nanoparticles (GNPs) synthesized using a citrate reduction method. HA functionalized GNP complexes (HA-GNPs) were characterized using absorption spectroscopy, scanning electron microscopy, zeta potential, and dynamic light scattering. GNP cellular uptake and potential dose-dependent cytotoxic effects due to treatment were evaluated in vitro in HeLa cells using ICP-OES and Trypan blue and MTT assays. Further, we quantified the in vivo biodistribution of intratumorally injected HA functionalized GNPs in Lewis Lung carcinoma (LLC) solid tumors grown on the flank of C57BL/6 mice and compared localization and retention with nascent particles. Our results reveal that HA-GNPs show overall greater peritumoral distribution (**p<0.005, 3 days post-intratumoral injection) than citrate-GNPs with reduced biodistribution in off-target organs. This property represents an advantageous step forward in localized delivery of metal nano-complexes to the infiltrative region of a tumor, which may improve the application of nanomedicine in the diagnosis and treatment of cancer.

A gold nanostructured film modified glassy carbon electrode (Au_film/GCE) was developed for the determination of chromium (VI) in water sample. GCE was immersed into HAuCl₄ solution (10^-3M) and electrodeposition of thin gold layer was conducted at –0.4 V (vs Ag/AgCl) for 10 min. The strong affinity between Au and Cr species resulted with increasing of Cr (VI) signal, compared with the bare glassy carbon electrode. The electrodepositing time, type of supporting electrolyte, pH, the scan rate, modulation amplitude, and modulation time were optimized using differential pulse anodic stripping voltammetry (DP-ASV). The calibration graph using accumulation time of 120 s was linear from 10 to 120 µgL^-1 with a sensitivity 1.3 x 10^-2 µA/µgL^-1. Under optimum experimental conditions, a good correlation coefficient R²=0.9971, and a low detection limit 5.5 µg/L Cr (VI) was obtained. The signal was reproducible with a relative standard deviation ±4.5 %. The developed Au_film/GCE sensor was applied for the Cr (VI) determination of in sewage water samples.

Background: Developing patient-centric baseline standards that enable the detection of clinically significant outlier gene products on a genome-scale remains an unaddressed challenge required for advancing personalized medicine beyond the small pools of subjects implied by “precision medicine”. This manuscript proposes a novel approach for reference standard development to evaluate the accuracy of single-subject analyses of metabolomes, proteomes, or transcriptomes. Since distributional assumptions of statistical testing may inadequately model genome dynamics of gene products, the so-called significant results of previous studies may artefactually conflate with real signals. Model confirmation biases escalate when studies use the same analytical methods in the discovery sets and reference standards, as corroboration of results leads to an evaluation of reproducibility confounded with replicated biases rather than a measure of accuracy. We hypothesized that developing method-agnostic reference standards using effect-size and expression-level filtering of results, obtained from multiple discovery methods that are distinct from the one evaluated, would maximize the evaluation of clinical-transcriptomic signals and minimize statistical artefactual biases. We developed and released an R package “referenceNof1” to facilitate the construction of robust reference standards. Results: Since RNA-Seq data analysis methods often rely on binomial and negative binomial assumptions to non-parametric analyses, the differences create statistical noise and make the reference standards method dependent. In our experimental design, the accuracy of 30 distinct combinations of fold changes (FC) and expression levels (EL) were determined for five types of RNA analyses in two different datasets. This design was applied to two distinct datasets: breast cancer cell lines and a yeast study with isogenic biological replicates in two experimental conditions. In addition, the reference standard (RS) comprised all RNA analytical methods with the exception of the method testing accuracy. To mitigate for biased optimization of the RS parameters towards a specific analytical method, similarity between observed results of distinct analytical methods were calculated across all methods (Jaccard Concordance Index). The greatest differences were observed across diametric extremes. For example, filtering out differentially expressed genes (DEGs) using a fold change < 1.2 leads to a 50% increase in concordance between techniques when compared to results with FC > 1.2. Combining this FC cutoff with genes with mean expressions > 30 counts leads to a 65% increase in concordance in comparison to genes with expression levels < 30 counts and with FC < 1.2. Conclusions: We have demonstrated that comparing accuracies of different single-subject analysis methods for clinical optimization requires a new evaluation framework. Reliable and robust reference standards, independent of the evaluated method, can be obtained under a limited number of parameter combinations: fold change (FC) ranges thresholds, expression level cutoffs, and exclusion of the tested method from the RS development process. When applying anticonservative reference standard frameworks (e.g., using the same method for RS development and for prediction), a majority of the concordant signal between prediction and Gold Standard (GS) cannot be confirmed by other methods, which we conclude as biased results. Statistical tests to determine DEGs from a single-subject study generate many biased results that require subsequent filtering for increasing their reliability. Conventional single-subject studies pertain to one or a few measures in one patient over time [1]and need a substantial conceptual framework extension in order to address the tens of thousands of measures in genome-wide analyses of gene products. The proposed referenceNof1 framework addresses some of the inherent challenges in improving transcriptome scale single-subject analyses by providing a robust approach to constructing reference standards. Github: https://github.com/SamirRachidZaim/referenceNof1

Imaging techniques such as computed tomographies (CT) play a major role in clinical imaging and diagnosis of malignant lesions. In recent years, spectral CT has emerged in the field of computed tomographies, utilizing detailed information from extracted spectral parameters of the specimen. Metal nanoparticle platforms enable effective payload delivery for this technique. Due to the possibility of surface modification, metal nanoparticles are predestined to facilitate molecular tumor targeting. In this work, we demonstrate the feasibility of anti-plasma membrane Heat shock protein 70 functionalized gold nanoparticles (AuNPs) for tumor specific multimodal imaging. Membrane-associated Hsp70 is exclusively presented on the plasma membrane of malignant cells of multiple tumor entities, but not on corresponding normal tissue cells, predestining this target epitope for tumor-selective in vivo targeting. In vitro microscopical analysis revealed the presence of cmHsp70.1-AuNP in the cytosol of tumor cell lines, being internalized via the endosomal-lysosomal pathway. In tumor bearing mice the biodistribution as well as the intratumorally enrichment of AuNP were examined 24h after i.v. application, in vivo. In parallel to spectral CT analysis, histological analysis confirmed the presence of tumor cells. In contrast to control NP, a significant enrichment of cmHsp70.1-AuNPs has been detected selectively in tumors of different preclinical mouse models. Furthermore, the biodistribution of AuNP, following i.v. injection, was analyzed by a machine-learning approach on digitalized slides. In summary, utilizing mHsp70 on tumor cells for guidance of cmHsp70.1 antibody functionalized nanoparticles enables sufficient enrichment and uniform distribution of AuNPs in mHsp70-expressing tumor cells, adequate for various microscopical imaging techniques and spectral-CT-based tumor delineation, in vivo.

Dayaoshan, as an important metal ore producing area in China, is faced with the dilemma of resource depletion due to long-term exploitation. In this paper, remote sensing method is used to circle the favorable metallogenic areas and find new ore points for Gulong. Firstly, vegetation interference bas been removed by using mixed pixel decomposition method with hyperplane and genetic algorithm (GA) optimization; then, altered mineral distribution information has been extracted based on principal component analysis (PCA) and support vector machine (SVM) method; Thirdly, the favorable areas of gold mining in Gulong has been delineated by using ant colony algorithm (ACA) optimization SVM model to remove false altered minerals; Lastly, field survey verified that the extracted alteration mineralization information is correct and effective. The results show that the mineral alteration extraction method proposed in this paper has certain guiding significance for metallogenic prediction by remote sensing.

The detection of dopamine in a highly sensitive and selective manner is crucial for the early diagnosis of a number of neurological diseases/disorders. Here, a report on a new platform for the electrochemical detection of dopamine with a considerable accuracy that comprises a 3D porous graphene oxide (pGO)/gold nanoparticle (GNP)/pGO composite-modified indium tin oxide (ITO) is presented. The pGO was first synthesized and purified by ultrasonication and centrifugation, and it was then further functionalized on the surface of a GNP-immobilized ITO electrode. Remarkably, owing to the synergistic effects of the pGO and GNPs, the 3D pGO-GNP-pGO-modified ITO electrode showed a superior dopamine-detection performance compared with the other pGO- or GNP-modified ITO electrodes. The linear range of the newly developed sensing platform is from 0.1 μM to 30 μM with a limit of detection (LOD) of 1.28 μM, which is more precise than the other previously reported GO-functionalized electrodes. Moreover, the 3D pGO-GNP-pGO-modified ITO electrodes maintained their detection capability even in the presence of several interfering molecules (e.g., ascorbic acid, glucose). The proposed platform of the 3D pGO-GNP-pGO-modified ITO electrode could therefore serve as a competent candidate for the development of a dopamine-sensing platform that is potentially applicable for the early diagnosis of various neurological diseases/disorders.

The gold(I) N-heterocyclic carbene (NHC) complexes, containing a combination of 1,3-bis(2,6-diisopropylphenyl)imidazol-2-ylidene (iPr) and the corresponding 7-azaindole derivative (HL1-4), were prepared and structurally characterized. The complexes of the composition of [Au(iPr)(HLn)], where n = 1–4 for 5-fluoro-7-azaindole (1), 5-bromo-7-azaindole (2), 3-chloro-7-azaindole (3) and 3-iodo-7-azaindole (4), were further evaluated for their in vitro anti-cancer and anti-inflammatory activities. The results showed that complexes (1–4) behave as considerably cytotoxic against human ovarian cancer cell line A2780 (with IC50 = 4–9 mircoM) and cisplatin-resistant cell line A2780R (with IC50 = 5–8 microM, except for 2 with IC50 > 25 microM), providing significantly higher cytotoxicity than anticancer drug cisplatin. Moreover, they also revealed a relatively good selectivity over normal cells (MRC-5), with the values of selectivity index, SI > 2.5. The complex 4 was further studied for its cellular effects in A2780 cells by cell cycle analysis, induction of apoptosis, intracellular ROS production, activation of caspases 3/7 and disruption of mitochondrial membrane potential. The ability of complexes (1–4) to influence the activity of pro-inflammatory transcription factor NF-κB and secretion of TNF-α were evaluated, showing that complex 4 reveals comparable effects as the inflammatory drug Auranofin.

Porphyry copper-molybdenum deposits (PCDs) are the world’s most important source of copper, molybdenum and rhenium. Previous studies have reported that some PCDs can have sub-economic to economic grades of critical metals, i.e., those elements that are both essential for modern societies and subject to the risk of supply restriction (e.g., platinum group elements (PGE), rare earth elements (REE), In, Co, Te, Ge, Ga, among others). Even though some studies have reported measured concentrations of Pd and Pt in PCDs, their occurrence and mineralogical form remain poorly constrained. Furthermore, these reconnaissance studies have focused predominantly on porphyry Cu-Au deposits, but very limited information is available for porphyry Cu-Mo systems. In this contribution, we report the occurrence of critical metal (Pd, Pt, Au, Ag, and Te) inclusions in copper sulfides from the world’s largest PCD, the supergiant Río Blanco-Los Bronces deposit in central Chile. Field emission scanning electron microscope (FESEM) observations of chalcopyrite and bornite from the potassic alteration zone reveal the presence of micro- to nano-sized particles (<1-10 μm) of noble metals, most notably Pd, Au, and Ag. The high-resolution data show that these inclusions are mostly tellurides, such as merenskyite [PdTe2], Pd-rich hessite [Ag2Te], sylvanite [(Ag, Au)Te2] and petzite [Ag3AuTe2]. The data point to Pd (and probably Pt) partitioning in copper sulfides during the high-temperature potassic alteration stage, opening new avenues of research aimed at investigating not only the mobility of PGE during mineralization and partitioning into sulfides, but also at evaluating the potential of porphyry Cu-Mo deposits as a source for noble metals.

The article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that was not previously studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are: pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies have established the presence of gold grains in free form, ranging in size from 0.9-10.2 mkm Au-ultrafine and fine gold. Obtaining a gold-containg concentrate with a gold content of 15.95 g / t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class -0.05 mm, additional grinding of hydrocyclone sands to a fineness of 90.0-95.0% of the class finer than 0.050 mm, and control centrifugal separation. Since pyrite in technogenic raw materials is the main gold-containing mineral, this paper presents studies on the oxidizability of pyrite with the TCCA oxidizer. The results of studies on the oxidation of pyrite using the TCCA oxidizer show that the products of its hydrolysis oxidize pyrite with the formation of various iron compounds on its surface. Pretreatment of gold-containing concentrate with oxidizer TCCA for 3 hours before the cyanidation process (20 hours) allows to increase the recovery of gold in the solution by 5.8 %.

The Mahuagou gold deposit is among the most important gold deposits in the core of Huangling Anticline. However, the geochemical exploration on the surface of the mining area presents challenges due to the thin overburde.This paper focuses on the overburden soil of Fengxiangshugou (FXS) – Mahuanggou (MHG) section as the research object, utilizes chemical form analysis of gold, soil halogen survey, and heat-released mercury survey to determine the key deep-penetrating geochemical methods for mining area. The results indicated that Si and Al components of samples exhibit minimal variation, suggesting that drift loads did not influence the overburden soil. Based on the systematic clustering, As, Sb, Mo, Bi, W and Hg emerge as ore-body or ore-belt front elements of hydrothermal gold deposits. In the study area, the predominant chemical form of gold in soil is the strong organic bond. Compared to the total amount, strong organic bound gold and heat-released mercury show higher anomaly contrasts, making them crucial indicators of faults, intrusions and hidden ore bodies. Consequently, chemical form analysis of gold and heat-released mercury surveys can enhance the anomaly contrast, proving beneficial for geochemical prospecting for weak anomalies in this area.

Developing particles of different anisotropic shapes are the hot topic since decades as they guarantee some special features of properties not possible through other means. Again, controlling atoms to develop certain size and shape particle is a quite challenging job. In this study, gold particles of different shapes are developed via pulse-based electronphoton-solution interface process. Gold atoms of certain transition state develop monolayer assembly at solution surface around the light glow (known in argon plasma) being generated at bottom of copper capillary (known in cathode). The rate of uplifting gold atoms to solution surface is being controlled by forcing energy (travelling photons) pursuing electrons and high energy photons (in high density) entering to solution. Gold atoms dissociated from the precursor under dissipating heat energy into the solution supplied under propagating photons characteristic current through immersed graphite rod (known in anode). Placing packets of nano shape energy of tuned pulse protocol over compact monolayer assembly comprising transition state atoms develop tiny-sized particles of formed shape. On separation of joint tiny particles into two equilateral triangular-shaped tiny particles, exerting forces of surface format elongate atoms of one-dimensional arrays converting them into structures of smooth elements. Due to immersing level of force, such tiny-shaped particles pack from different zones at centre of light glow where they assembled structures of smooth elements for developing mono-layers of different shapes of particles. Developing one-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from nearly rearward zones of reflection of north-south poles, whereas, developing multi-dimensional particles deal assembling of structures of smooth elements of packing tiny-shaped particles from the east-west poles and near regions. Depending on the number of assembled structures of smooth elements at point of nucleation, packing of tiny-shaped particles from different zones develop different shapes of the anisotropic particles. At fixed precursor concentration, increasing the process time results into develop particles of low aspect ratio. Under tuned parameters, developing mechanisms of particles exhibiting unprecedented features are discussed.

Avocado (Persea americana Mill.) plant fruits are well-known for their high nutritional value, unique test, and healthy oil. It has a history of about 10,000 years. Avocado fruit offers many health benefits, and its production is rapidly increasing. The Food and Agriculture Organization (FAO)’s recent data suggest that the Avocados produced in the world in 2019 was twice that of 2010 (3778010 tons). Avocado’s global Gross Production Value was about 5.812 billion USD in 2018, and it is likely to increase rapidly because of the increasing demand for Avocado fruits. Avocado oil is also used in the cosmetic industry because of its therapeutic properties, and it boosts the economic value of the Avocado industry. Avocado fruits have a rough green-gold skin; however, fruits are called ‘the green gold’ because of their massive global demand in the worldwide market and a lucrative business. The cultivation of Avocado has tremendous potential in increasing the rural economy, rural agriculture-based employment and reducing the poverty rate of growers. On the other hand, the Avocado industry is highly criticised because of deforestation, massive water utilisation, polluting water bodies with insecticides and fertilisers, posing a threat to other plant species, and environmental pollution. However, it doesn’t preclude the importance of Avocado. Cameroon’s average temperature is about 23 °C, which is considered optimal for Avocado propagation and commercial cultivation. Cameroon Association of Active Youths (CAMAAY) want to explore the possibilities of engaging Cameroon youths in Avocado cultivation. This review is aimed to provide an overview of Avocado. The review also highlights Avocado cultivation related issues from one health and sustainability perspective in line with the global goals.

Selenium-rich Au-Ag mineralization has been discovered in the Kremnica ore district, central Slovakia. The mineralization is hosted by a single quartz-dolomite vein hosted by Neogene propyllitized andesites of the Kremnica stratovolcano. Ore mineralogy and crystal chemistry of individual ore minerals have been studied here. The early base-metal ore mineralization composed of pyrite, sphalerite and chalcopyrite lacks selenium, whereas the superimposed Au-Ag paragenesis is Se-enriched. The Au-Ag alloys, uytenbogaardtite, minerals of the galena-clausthalite series, acanthite-naumannite series, diaphorite, miargyrite, pyrargyrite-proustite, polybasite group, minerals of the tetrahedrite group and andorite branch (andorite IV, andorite VI, Ag-excess fizélyite), freislebenite, and rare Pb-Sb sulphosalts (scaiinite, robinsonite, plagionite) have been identified here. Besides selenides, the most Se-enriched phases are miargyrite, proustite-pyrargyrite, and polybasite-pearceite, whose Se contents are among the highest reported worldwide. In addition, one new phase has been found, corresponding to a Se-analogue of pearceite containing 2.08 - 3.54 apfu Se. The style of mineralization, paragenetic situation, and chemical trends observed in individual minerals are comparable to those of Au-Ag low-sulphidation epithermal Au-Ag mineralizations of the Kremnica and neighboring Štiavnica and Hodruša-Hámre Ore Districts, however, the pronounced enrichment in selenium is a specific feature of the studied vein only.

Background: In chronic obstructive pulmonary disease (COPD), there are two known classifications for assessing what is called disease severity. One is the Global Initiative for Chronic Obstructive Lung Disease (GOLD) classification, which is based on the post-bronchodilator value of FEV1 (% reference). The other is the STaging of Airflow obstruction by Ratio (STAR). Methods: We reanalyzed data from our outpatient cohort study, which included 141 participants with COPD from 2015 to 2023. We compared mortality and COPD-specific health status between the GOLD 1 to 4 groups and the STAR 1 to 4 groups. Results: By simple calculation, GOLD and STAR severity classes coincided in 75 participants (53.2%). The weighted Bangdiwala B value with linear weights was 0.775. The participants were observed for up to 95 months, with a median of 54 months. Death was confirmed in 29 participants (20.5%). In univariate Cox proportional hazards analyses, there was a significant difference in mortality between the GOLD 1 and GOLD 3+4 groups, with the GOLD 1 group used as the reference [Hazard Ratio 4.222 (95% CI 1.298 - 13.733), p=0.017]. However, there was no statistically significant predictive relationship between STAR 1 and STAR 2, or between STAR 1 and STAR 3+4. The St. George's Respiratory Questionnaire (SGRQ) Total and COPD Assessment Test (CAT) scores were significantly different between all GOLD groups, except for the CAT score between GOLD 1 and GOLD 2. The SGRQ Total and CAT scores were significantly different between STAR 1 and STAR 3+4, but not between STAR 1 and STAR 2. Conclusion: From the perspective of all-cause mortality and COPD-specific health status, the GOLD classification is more discriminative than STAR.

Parasite control strategies such as blanket anthelmintic treatment of all horses in a herd or interval treatment regimen based on egg reappearance remain widely followed practices for the last several decades. These practices have resulted in the fast emergence of resistance in equine strongyles to all major classes of drugs on the market. In this regard, the guidelines set by the American Association of Equine Practitioners advocate evidence-based strongyle control in horses. It recommends targeted treatment of all heavy egg shedders [&gt; 500 eggs per gram (EPG) of feces] while the low shedders (0-200 EPG) are left untreated to maintain susceptible parasite refugia in a herd. As 50-75% of adult horses in a herd are low shedders, preventing them from unnecessary anthelmintic exposure is critical to tackling resistance. There are various fecal egg count (FEC) techniques with many modifications and variations in use, but none is identified as a gold standard and methods comparison studies are lacking. We hypothesized that the diagnostic performance of commonly used quantitation methodologies differs and the FEC methods must be evaluated to determine the gold standard. In this regard, we performed methods comparison studies using polystyrene beads with size and specific gravity comparable to strongyle eggs, as proxy. The linearity of 12 commonly used FEC methodologies (3 techniques with 4 different solutions) was studied using bead standards in the clinically applicable range (63 to 1,000) to determine their suitability for strongyle egg counts. Deming regression analysis identified Mini-FLOTAC with sugar (specific gravity 1.33) as the test with the greatest coefficient of determination. All tests underestimated the true bead count, and we determined a correction factor (CF) for each test to estimate the true count. CF negates the preference for a gold standard test. Finally, we analyzed the validity of CF for 5 tests with R2&gt;0.95 to accurately quantify strongyle eggs from 40 different horses. Overall, this study identified methodologies with the highest diagnostic performance and the limitations to standardizing routine FEC tests to promote uniformity in implementing AAEP parasite control guidelines.