The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FTIR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141–238 (L/m²·h·MPa) and superior salt rejection of Na₂SO₄ > 98.4%.

The rapid and extensive loss of biodiversity globally has resulted in an increased urgency to capture and conserve the diversity which is present, including genetic diversity within species. However, for many species there is currently no detailed genetic data available to inform the collection and use of material held in ex situ collections and this can hamper the consideration of genetic issues and reduce the likelihood collection represent the diversity present. Even in the absence of direct genetic data, however, it is possible to consider genetic issues using the existing theoretical and empirical evidence-based and biological, ecological and demographic data for a given species. Here a framework to facilitate the consideration of genetic diversity and genetic issues, even where genetic data is lacking, is presented.

Structure quality of LuFeO3 epitaxial layers grown by pulsed-laser deposition on sapphire substrates with and without platinum interlayers has been investigated by in-situ high-resolution x-ray diffraction (reciprocal-space mapping). The parameters of the structure such as size and misorientation of mosaic blocks have been determined as functions of the thickness of LuFeO3 during the PLD growth and for different platinum interlayers thicknesses up to 40 nm. The x-ray diffraction results combined with ex-situ scanning electron microscopy and high-resolution transmission electron microscopy demonstrate that the Pt interlayer significantly improves the structure of LuFeO3 by reducing the misfit of the LuFeO3 lattice with respect to the material underneath.

Lemon balm extracts by dry plant material of Melissa officinalis were tested against their efficacy against for different fungal species Alternaria alternata, Fusarium oxysporum, Aspergillus flavus and Beauveria bassiana. The aqueous phase of the extract was evaluated for antioxidant, antifungal and also anti-aflatoxigenic activity. A synergism evaluation was also performed concerning, the small quantity of lemon balm polar essential oil compounds extracted into the infusion and the water soluble compounds in the extract. The experiments were conducted in solid cultures and the growth inhibition was demonstrated by measuring mycelial diameter. Additionally, the effect on conidia production was also demonstrated. Lemon balm was also used for in situ test on Pistachia vera seed against Aspergillus flavus growth and aflatoxin production. Results revealed enhancement of fungal growth by lemon balm extracts however total inhibition of aflatoxins production on Pistachia vera seeds was observed, and both actions were tried to attributed to volatile and water soluble compounds identified based on GC/MS, HPLC/DAD and LC/MS, and the observed antioxidant activity. Volatile and water - soluble compounds found to be in absolute synergism in mycelium growth enhancement and the observed anti-aflatoxigenic activity addressed to the high antioxidant activity observed and synergistic action between the other water soluble phenolic compounds identified in the extract. The findings of this study underline the high biological active potential of lemon balm extracts under various screening test since for the first time full phytochemical analysis of lemon balm extracts.

The rapid expansion of transcriptomics from increased affordability of next-generation sequencing (NGS) technologies generates rocketing amounts of gene expression data across biology and medicine, and notably in cancer research. Concomitantly, many bioinformatics tools were developed to streamline gene expression analysis and quantification. We tested the concordance of NGS RNA sequencing (RNA-seq) analysis outcomes between the two predominant programs for reads alignment, HISAT2 and STAR, and the two most popular programs for quantifying gene expression in NGS experiments, edgeR and DESeq2, using RNA-seq data from a series of breast cancer progression specimens, which include histologically confirmed normal, early neoplasia, ductal carcinoma in situ and infiltrating ductal carcinoma samples microdissected from formalin fixed, paraffin embedded (FFPE) breast tissue blocks. We identified significant differences in aligners’ performance: HISAT2 was prone to misalign reads to retrogene genomic loci, STAR generated more precise alignments, especially for early neoplasia samples. edgeR and DESeq2 produced similar lists of differentially expressed genes in stage comparisons, with edgeR producing more conservative, though shorter, lists of genes. Albeit, Gene Ontology (GO) enrichment analysis revealed no skewness in significant GO categories identified among differentially expressed genes by edgeR vs DESeq2. As transcriptome analysis of archived FFPE samples becomes a vanguard of precision medicine, identification and fine-tuning of bioinformatics tools becomes critical for clinical research. Our results indicate that STAR and edgeR are well-suited tools for differential gene expression analysis from FFPE samples.

Current prenatal genetic evaluation showed a significantly increase in non-invasive screening and the reduction of invasive diagnostic procedures. To evaluate the diagnostic efficacy on detecting common aneuploidies, structural chromosomal rearrangements and pathogenic copy number variants (pCNV), we performed a retrospective analysis on a case series initially analyzed by aneuvysion fluorescence in situ hybridization (FISH) and karyotyping then followed by array comparative genomic hybridization (aCGH). Of the 386 cases retrieved from the past decade, common aneuploidies were detected in 137 cases (35.5%), other chromosomal structural rearrangements were detected in four cases (1%), and pCNV were detected in five cases (1.3%). The relative frequencies for common aneuploidies suggested a under detection of sex chromosome aneuploidies. Approximately 9.5% of cases with common aneuploidies showed a mosaic pattern. Inconsistent results between FISH and karyotyping were noted in cases with pseudo-mosaicism introduced by culture artifact or variable cellular proliferation from cells with mosaic karyotypic complements under in vitro cell culture. Based on findings from this case series, cell-based FISH and karyotyping should be performed to detect common aneuploidies, structural chromosomal abnormalities, and mosaic pattern. DNA-based aCGH and reflex FISH should be performed to detect and confirm genomic imbalances and pCNV. Practice points to ensure the diagnostic accuracy and efficacy were summarized.

Three kinds of hydrophobic groups grafted starches of maleic anhydride grafted starch (MAH-g-starch), lactic acid grafted starch (LA-g-starch), and methyl acrylate grafted starch (MA-g-starch) were prepared by in-situ solid phase polymerization. The results of Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) were confirmed successful grafting. The grafting ratios of MAH-g-starch, LA-g-starch and MA-g-starch were 6.50%, 12.45%, and 0.57%, respectively. Influenced by the grafting ratio, LA-g-starch had the best hydrophobic properties and the largest molecular weight, and those for MA-g-starch was the worst. The surfaces of grafted starches were covered with graft polymer, with obvious surface roughness and bond degree of MAH-g-starch and LA-g-starch. The crystalline structure of grafted starches showed some damage, with LA-g-starch exhibiting the greatest decrease in crystallinity, and less of a change for MA-g-starch. Overall, the grafting reaction improved thermoplasticity, with LA-g-starch the most improved, followed by MAH-g-starch, and then MA-g-starch.

The microstructure of Al-5Fe-1.5Er alloy was characterized and analyzed by using XRD, SEM, TEM and EDS. The effect of microstructure on the behavior of crack initiation and propagation was investigated by in situ tensile testing. Results show that the microstructure consists of α-Al matrix, Al₃Fe, Al₄Er, eutectic phase Al₃Fe + Al₄Er, while the 1.5 wt.% Er was added in Al-5Fe alloy. The twin structure of the Al₃Fe phase was observed, and the twin plane is {001}. Moreover, a continuous concave and convex interface structure of the Al₄Er has been found. Al₃Fe is in the form of a sheet with a clear gap inside.In situ tensile tests of the alloy at room temperature show that the crack initiation occured mainly in the Al₃Fe phase, and that the crack propagation modes include intergranular and transgranular expansion. Crack transgranular expansion is due to the strong binding ability between Al₄Er phases and surrounding organization, and the continuous concave and convex interface structure of the Al₄Er provides a significant meshing effect on the matrix and eutectic structure.

Cariogenic oral biofilms cause a considerable amount of recurrent dental caries around composite restorations every year, resulting in unprosperous oral health status and expensive restorative treatment for many patients. Quaternary ammonium monomers that can be copolymerized with the current dental resin systems have been increasingly explored for modulation of dental plaque biofilm growth over dental composite surfaces. Here, we investigated the effect of bis(2-methacryloyloxyethyl) dimethylammonium bromide (QADM), against human overlying mature oral biofilms grown intra-orally in human participants for 7 and 14 days, for the first time. Seventeen volunteers wore palatal devices containing composite specimens containing 10% by mass of QADM or a control composite without QADM. After 7 and 14 days, the adherent biofilms were collected for determination of bacterial counts via colony-forming unit (CFU) counts. The biofilm viability, chronological changes, and percentage coverage were also determined by live/dead staining. QADM composites caused a significant inhibition of S. mutans biofilm formation for up to seven days. No difference in the CFU values were found for the 14-day period. Our findings suggest that (1) QADM composite was successful in inhibiting 1-3 day biofilms in the oral environment in vivo; (2) QADM significantly reduced the portion of S.mutans group in a time course where patients at high risk of caries would develop initial enamel carious lesions; and (3) stronger antibiofilm activity is required for the control of mature long-term cariogenic biofilms. These results provide a perspective on the value of integrating bioactive restorative materials with traditional caries management approaches into clinical practice. Contact-killing strategies via dental materials aiming to prevent or at least reduce high numbers of cariogenic bacteria seem to be a promising approach in patients at high risk of recurrence of dental caries around composites.

The alignment of nanostructures in materials such as lyotropic liquid crystals (LLCs) templated materials has the potential to signicantly improve their performances. However, accurately characterising and quantifying the alignement of such fine structures remains very challenging. In situ small angle X-ray scattering (SAXS) and molecular dynamics were employed for the first time to understand the hexagonal LLC alignment process with magnetic nanoparticles under a magnetic field. The enhanced alignment has been illustrated from the distribution of azimuthal intensity in the samples exposed to magnetic field. Molecular dynamics simulations reveal the relationship between the imposed force of the magenetic nanoparticles under magnetic field and the force transferred to the LLC cylinders which leads to the LLC alignment. The combinational study with experimental measurement and computational simulation will enable the development and control of nanostructures in novel materials for various applications.

In this present study, 3-pentadecyl-phenol was selected as a modifier to prepare a foamable phenolic resin with excellent performance, which was successfully prepared by in-situ modification. Fourier transform infrared spectroscopy (FT-IR) and nuclear magnetic resonance (¹H NMR, ¹³C-NMR) were used to test and characterize the molecular structure of the modified resin. The results showed that 3-pentadecyl-phenol successfully modified the molecular structure of phenolic resin with a reduction in resin gel time. The effect of changing the added amount of 3-pentadecyl-phenol on the mechanical properties, microstructure and flame retardancy of the modified foam was investigated. The results showed that when the amount of added 3-pentadecyl-phenol was 15% of the total amount of phenol, this resulted in the best toughness of the modified foam, which could be increased to 300% compared to the bending deflection of the unmodified phenolic foam. The cell structure showed that the modified phenolic foam formed a more regular and dense network structure and the closed cell ratio was high. Furthermore, the compressive strength, bending strength, and limited oxygen index were improved, while the water absorption rate was lowered. However, the foam density could be kept below 40 mg/cm³, which does not affect the load.

New approaches to collect in-situ data are needed to complement the high spatial (10~m) and temporal (5-day) resolution of Copernicus Sentinel satellite observations. Making sense of Sentinel observations requires high quality and timely in-situ data for training and validation. Classical ground truth collection is expensive, lacks scale, fails to exploit opportunities for automation, and is prone to sampling error. Here we evaluate the potential contribution of opportunistically exploiting crowd-sourced street-level imagery to collect massive high-quality in-situ data in the context of crop monitoring. This study assesses this potential by answering two questions: 1) what is the spatial availability of these images across the European Union (EU)? and 2) can these images be transformed to useful data? To answer the first question, we evaluated the EU availability of street-level images on Mapillary - the largest open-access platform for such images - against the Land Use and land Cover Area frame Survey (LUCAS) 2018, a systematic surveyed sampling of 337031 points. For 37.78% of the LUCAS points a crowd-sourced image is available within a 2-km buffer, with a mean distance of 816.11 m. We estimate that 9.44% of the EU territory has a crowd-sourced image within 300-m from a LUCAS point, illustrating the huge potential of crowd-sourcing as a complementary sampling tool. After artificial and built up (63.14%), and inland water (43.67%) land cover classes, arable land has the highest availability at 40.78%. To answer the second question, we focus on identifying crops at parcel level using all 13.6 million Mapillary images collected in the Netherlands. Only 1.9% of the contributors generated 75.15% of the images. A procedure was developed to select and harvest the pictures potentially best suited to identify crops using the geometries of 785710 Dutch parcels and the pictures' meta-data such as camera orientation and focal length. Availability of crowd-sourced imagery looking at parcels was assessed for 8 different crop groups with the 2017 parcel level declarations. Parcel revisits during the growing season allowed to track crop growth. Examples illustrate the capacity to recognize crops and their phenological development on crowd-sourced street-level imagery. Consecutive images taken during the same capture track allow selecting the image with the best unobstructed view. In the future, dedicated crop capture tasks can improve image quality and expand coverage in rural areas.

The issues of metallic scrap management and its utilization in manufacturing plants are nowadays intensely considered to address essential sustainability guidelines. Efficient recycling procedure for shop floor metallic scrap is not yet available because of abundance and contamination of nonmetallic constituents. Other ferrous metallic scrap are melted and purified during secondary steelmaking to get products in the form of blooms and billets are obtained. This study illustrates the potential of powder technology (powder metallurgy (PM) and metal injection molding (MIM)) based process for solid-state recycling and attainment of usable products. Industrially downgraded grinding sludge is pulverized and used as a raw material. Results showed properties of sintered parts are significantly improved due to in-situ reduction and densification during sintering. Recyclability Index (RI) was created to compare the effect of process variables on obtained products. Based on RI, recycled ferrous parts have about 70% comparable properties with equivalent pure iron parts. Complex reduction and sintering behavior in MIM, particularly, diffusion and pore volume kinetics limits applicability of MIM with this recycling approach. However, few industrial parts were developed and manufactured by PM based approach to validate the applicability of this novel recycling-cum-manufacturing process for the production of porous parts.

Hybrid inorganic-polymer nanocomposites can be employed in diverse applications due to the potential combination of desired properties from both the organic and inorganic components. The use of novel bottom-up in situ synthesis methods for the fabrication of these nanocomposites is advantageous compared to top-down ex situ mixing methods, as it offers increased control over the structure and properties of the material. In this review, the focus will be on the application of the sol-gel process for the synthesis of inorganic oxide nanoparticles in epoxy and polysiloxane matrices. The effect of the synthesis conditions and the reactants used on the inorganic structures formed, the interactions between the polymer chains and the inorganic nanoparticles, and the resulting properties of the nanocomposites are appraised from several studies over the last two decades. Lastly, alternative in situ techniques and the applications of various polymer-inorganic oxide nanocomposites are briefly discussed.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

This paper reports on the production and mechanical properties of Ti6Al4V micro-lattice structures, with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the mechanical properties and manufacturability of such thin-strut lattices, this paper also reports on the in-situ deformation imaging of micro-lattice structures with 6 unit cells in every direction. LPBF lattices are of interest for medical implants, due to the possibility of creating structures with an elastic modulus close to that of the bones and small pore sizes which allow effective osseointegration. In this work four different cubes were produced by laser powder bed fusion and subsequently analyzed using microCT, compression testing and one selected lattice was subjected to in-situ microCT imaging during compression. The in-situ imaging was performed at 4 steps during yielding. The results indicate that mechanical performance (elastic modulus and strength) correlate well with actual density and that this performance is remarkably good, despite the high roughness and irregularity of the struts at this scale. In-situ yielding is visually illustrated.

Transition-metal-catalyzed amide bond formation from alcohols and amines is an atom-economic and eco-friendly route. Herein, we identified a highly active in situ N-heterocyclic carbene (NHC)/ruthenium (Ru) catalytic system for this amide synthesis. Various substrates, including sterically hindered ones, could be directly transformed into the corresponding amides with the catalyst loading as low as 0.25 mol%. In this system, we replaced the p-cymene ligand of the Ru source with a relatively labile cyclooctadiene (cod) ligand so as to more efficiently obtain the corresponding poly-carbene Ru species. Expectedly, the weaker cod ligand could be more easily substituted with multiple mono-NHC ligands. Further HR-MS analyses revealed that two tetra-carbene complexes were probably generated from the in situ catalytic system.

We employ the solution concept of ex post Nash equilibrium to predict the interaction of a finite number of agents competing in a finite number of basic games simultaneously. The competition is called a multi-game. For each agent, a specific weight, considered as private information, is allocated to each basic game representing its investment in that game and the utility of each agent for any strategy profile is the weighted sum, i.e., convex combination, of its utilities in the basic games. Multi-games can model decision making in multi-environments in a variety of circumstances, including decision making in multi-markets and decision making when there are both material and social utilities for agents as, we propose, in the Prisoner's Dilemma and the Trust Game. Given a set of pure Nash equilibria, one for each basic game in a multi-game, we construct a pure Bayesian Nash equilibrium for the multi-game. We then focus on the class of so-called uniform multi-games in which each agent is constrained to play in all games the same strategy from an action set consisting of a best response per game. Uniform multi-games are equivalent to multi-dimensional Bayesian games where the type of each agent is a finite dimensional vector with non-negative components. A notion of pure type-regularity for uniform multi-games is developed and it is shown that a multi-game that is pure type-regular on the boundary of its type space has a pure ex post Nash equilibrium which is computed in constant time with respect to the number of the types and is independent of prior probability distributions. We then develop an algorithm, linear in the number of types of the agents, which tests if a multi-game is pure type-regular on the boundary of its type space in which case it returns a pure ex post Nash equilibrium for the multi-game.

Bamboo plastic composites have become a hot research topic and a key focus of research. However, the many strong, polar, hydrophilic hydroxyl groups in bamboo flour (BF) results in poor interfacial compatibility between BF and hydrophobic polymers. Maleic anhydride-esterified (MAH-e-BF) and lactic acid-esterified bamboo flour (LA-e-BF) were prepared using an in situ solid-phase esterification method with BF as the raw material and maleic anhydride or lactic acid as the esterifying agent. Fourier transform infrared spectroscopy results confirmed that BF esterification with maleic anhydride and lactic acid was successful, with the esterification degrees of MAH-e-BF and LA-e-BF at 21.04 and 14.36%%, respectively. Esterified BF was characterized by scanning electron microscopy, contact angle testing, X-ray diffractometry, and thermogravimetric analysis. The results demonstrated that esterified BF surfaces were covered with graft polymer and the surface roughness and bonding degree of MAH-e-BF clearly larger than those of LA-e-BF. The hydrophobicity of esterified BF was significantly higher than BF and the hydrophobicity of MAH-e-BF better than LA-e-BF. The crystalline structure of esterified BF showed some damage, with MAH-e-BF exhibiting a greater decrease in crystallinity than LA-e-BF. Overall, the esterification reaction improved BF thermoplasticity, with the thermoplasticity of MAH-e-BF appearing better than LA-e-BF.

The study was done to investigate the kinetics of first order bioremediation. The effectiveness of remediating soils polluted with raw crude oil and treated crude oil using Aspergillus niger (fungi) and Pseudomonas aeruginosa (bacteria) were investigated. Eight systems of 500g soil sample were polluted with both raw and treated crude oil. Four systems were polluted with 40g treated crude oil while the other remaining four systems were polluted with 40g raw crude oil. Two systems with raw crude and treated crude were left as control (RCC and TCC). Raw crude samples were treated with Aspergillus niger only (RCA) and Pseudomonas aeruginosa (RCP) while treated crude samples were also treated with same (TCA) and (TCP) only. The last two systems were treated with both Pseudomonas aeruginosa and Aspergillus niger (RCAP and TCAP). The first order bioremediation kinetics and biostimulant efficiency for these systems were studied by monitoring Total Petroleum Hydrocarbon (TPH). At the end of the bioremediation period, the results obtained showed that treated crude oil polluted soil generally remediated faster and better than raw crude oil polluted soil. The highest level of bioremediation occurred in systems amended with both Pseudomonas aeruginosa and Aspergillus niger which had about 98% TPH decrease.

In this paper, we investigate the use of fat tissue as a communication channel between in-body, implanted devices at R-band frequencies (1.7–2.6 GHz). The proposed fat channel is based on an anatomical model of the human body. We propose a novel probe that is optimized to efficiently radiate the R-band frequencies into the fat tissue. We use our probe to evaluate the path loss of the fat channel by studying the channel transmission coefficient over the R-band frequencies. We conduct extensive simulation studies and validate our results by experimentation on phantom and ex-vivo porcine tissue, with good agreement between simulations and experiments. We demonstrate a performance comparison between the fat channel and similar waveguide structures. Our characterization of the fat channel reveals propagation path loss of 1.4 dB and 3.8 dB per 20 mm for phantom and ex-vivo porcine tissue, respectively. These results demonstrate that fat tissue can be used as a communication channel for high data rate intra-body networks.

Polymer flooding is one of the most successful chemical EOR methods, and is primarily implemented to accelerate oil production by sweep improvement. However, other benefits have extended the utility of polymers. During the last decade, it has been evaluated for an increasing number of fields, both offshore and onshore. This is a consequence of improved polymer properties, which extends the use to HTHS (high temperature high salinity) conditions and of improved understanding of flow mechanisms such as for heavy oil mobilization. A key issue in understanding polymer performance is to control and predict in-situ porous medium rheology. The first part of this paper reviews recent developments in understanding polymer flow in porous medium. Especially, polymer in-situ rheology and injectivity is discussed. The second part of this paper reports polymer flow experiments using the most applied polymer for EOR processes, HPAM (partially hydrolyzed polyacrylamide). The experiments address high rate near-wellbore behavior (radial flow) as well as reservoir rate steady state flow (linear flow) and discuss differences observed in terms of flow conditions. In addition, impact of oil on polymer rheology was investigated, and compared to single-phase polymer flow in Bentheimer sandstone rock material. Presence of oil leads to a reduction in apparent viscosity.

Transferring in vitro-cultured Eustoma seedlings to an ex vitro condition (acclimation) is a big challenge that may expose the seedlings to biotic and abiotic stresses, and affect the internal and external structure of the plants. In addition, in vitro-cultured seedlings of Eustoma are difficult to handle and phenotype and physiological traits such as survival and rosette rate may have altered in the acclimation stage. Therefore, the present study aims to examine the effects of blue, red, and white LED light on the growth and development ex vitro of in vitro-cultured seedlings of Eustoma. The results showed that blue LEDs resulted in greater plant height, internode length, and leaf number, increased upper and lower fresh biomass, and higher chlorophyll content compared with treatment by the other LED lights. Higher stomatal density on the abaxial leaf surface was also observed in the blue LED-treated plants, which also showed a higher survival rate and lower rosette rate. In contrast, the white LED-treated plants had the highest leaf width and internode diameter. Acclimation of the Eustoma plants ex vitro suggests that a combination of blue and white LEDs may be advantageous for better growth and development for large-scale production in a controlled environment.

Ferroelectric materials are crucial for today’s technological society, and nanostructured ferroelectric materials are important for downscaling of devices. Controlled and reproducible synthesis of these materials are therefore of immense importance. Hydrothermal synthesis is a well-established synthesis route, with a large parameter space for optimization, but a better understanding of nucleation and growth mechanisms is needed for full utilization and control. Here we use in situ X-ray diffraction to follow the nucleation and growth of BaTiO₃ formed by hydrothermal synthesis using two different titanium precursors, an amorphous titania precipitate slurry and a Ti-citric acid complex solution. Sequential Rietveld refinement was used to extract the time dependency of lattice parameters, crystallite size, strain and atomic displacement parameters. Phase pure BaTiO₃ nanoparticles 10 - 15 nm in size were successfully synthesized at different temperatures (100, 125, and 150 °C) from both precursors after reaction times ranging from a few seconds, to several hours. The two precursors resulted in phase pure BaTiO₃ with similar final crystallite size. Finally, two different growth mechanisms were revealed, where the effect of surfactants present during hydrothermal synthesis is discussed as one of the key parameters.

With the progress of immunotherapy in cancer, oncolytic viruses (OVs) are getting more and more attention during the past decade. Due to their cancer-selective and immunogenic property, OVs are considered ideal candidates to be combined with immunotherapy to increase both specificity and efficacy in cancer treatment. OVs preferentially replicate in and lyse cancer cells, generating pathogen-associated molecular patterns (PAMPs) and danger (damage)-associated molecular patterns (DAMPs). These signals trigger innate immune response to modulate the solid tumor microenvironment, resulting in in situ autovaccination leading to adaptive anti-virus and anti-tumor immunity. Here, we summarize the conceptual updates of oncolytic virotherapy, immunotherapy, and the strategies to enhance the virus-mediated anti-tumor immune response, including: 1. Arm OVs with cytokines to modulated innate and adaptive immunity; 2. Combine OVs with immune checkpoint inhibitors to release T cell inhibition; 3. Combine OVs with immune co-stimulators to enhance T cell activation.

Metal and alloy toughening was the core and long-term research direction in materials filed. As grain size had bimodal distribution, micro/nano-structured alloys presented excellent comprehensive mechanical properties, and this had become one of the research hotspots and developing trends in the field of nanotechnology. In-situ tensile test was a direct and effective method to study the deformation mechanism of materials, which revealed the multiple mechanisms responding to feature grain sizes and provided reliable experimental means and research technique. Research on development of in-situ technique and its applications in mechanical properties was reviewed in this paper according to the recent advances on the modern mechanical properties for high strength and high plasticity alloy at home and abroad. The disadvantages of the present study of preparation methods and investigation techniques for high-performance alloy had been concluded. Finally, the development prospects of high strength and high plasticity alloy materials were analyzed.

In this paper the authors describe the architecture of a multidisciplinary data acquisition and visualization platform devoted to the management of coastal environments. The platform integrates heterogeneous data acquisition sub-systems that can be roughly divided in two main categories: remote sensing systems and in-situ sensing systems. Remote sensing solutions include aerial and underwater remote data acquisition while in-situ sensing solutions include the use of RFID tracers, Wireless Sensor Networks and imaging techniques. All the data collected by these subsystems are stored, integrated and fused on a single platform that is also in charge of data visualization. This last task is carried out according to the paradigm of Augmented Virtuality which foresees the augmentation of a virtually reconstructed environment with data collected in the real world. The described solution proposes a novel holistic approach where different disciplines concur, with different data acquisition techniques, to a large scale definition of coastal dynamics, in order to better describe and face the coastal erosion phenomenon. The overall framework has been conceived by the so-called Team COSTE, a joint research team between the Universities of Pisa, Siena and Florence.

Nitrogen use efficiency (NUE) in maize (Zea mays L.) is an important trait to maximize yield with minimal input of nitrogen (N) fertilizer. Expired Plant Variety Protection (ex-PVP) Act-certified germplasm may be an important genetic resource for public breeding sectors. The objectives of this research were to evaluate the genetic variation of N-use traits and to characterize maize ex-PVP inbreds adapted to the U.S. Corn Belt for NUE performance. Eighty-nine ex-PVP inbreds [36 stiff stalk synthetic (SSS), and 53 non-stiff stalk synthetic (NSSS)] were genotyped using 26,769 single-nucleotide polymorphisms, then 263 single-cross maize hybrids derived from these inbreds were grown in eight environments from 2011 to 2015 at two N fertilizer rates (0 and 252 kg N ha⁻¹) and three replications. Genetic utilization and the yield response to N fertilizer were stable across environments and were highly correlated with yield under low and high N conditions, respectively. Cluster analysis identified inbreds with desirable NUE performance. However, only one inbred (PHK56) was ranked in the top 10% for yield under both N-stress and high N conditions. Broad-sense heritability across 12 different N-use traits ranged from 0.11 to 0.77, but was not associated with breeding value accuracy. Nitrogen-stress tolerance was negatively correlated with the yield increase from N fertilizer.

The formation of solid solution series Cs_1-xM_xGaQ₂-mC64 (M = K, Rb; Q = S, Se; x = 0–1) was studied by X-ray diffraction and spectroscopic methods, revealing a complete miscibility of CsGaQ₂-mC64 with RbGaQ₂ and KGaSe₂, and a large miscibility gap with KGaS₂. All solid solution members exhibit similar Raman spectra, indicating the covalent Ga-Q bonding character. The similar optical band gaps likewise further contribute to this conclusion. Up to a degree of substitution, these solid solutions undergo a phase transition similar to CsGaQ₂-mC64. The influence of the substitution parameter x on phase transition process was investigated in situ using high-temperature X-ray powder diffraction experiments. Phase-pure solid solutions of the high-temperature polymorphs Cs_1-xM_xGaQ₂-mC16 were obtained up to x_max(K) = 0.1 and x_max(Rb) = 0.3. The crystal structures of these new CsGaQ₂-mC16 analogous high-temperature phases were refined from synchrotron diffraction data by Rietveld-refinement.

This work focuses on the study of the microstructure, hardening and stiffening effect caused by the secondary phases formed in titanium matrices. These secondary phases were originated from reactions between the matrix and boron particles added in the starting mixtures of the composites. Not only was the composite composition studied as an influencing factor in the behaviour of the composites, but also different operational temperatures. Three volume percentages of boron content were tested (0.9, 2.5 and 5 vol % of amorphous boron). The manufacturing process used to produce the composites was inductive hot pressing, which operational temperatures were between 1000 °C to 1300 °C. Specimens showed optimal densification. Moreover, microstructural study revealed the formation of TiB in various shapes and proportions. Mechanical testing confirmed that the secondary phases had a positive influence on the properties of the composites. In general, adding boron particles increased the hardness and stiffness of the composites; however rising temperatures resulted in greater increases in stiffness than in hardness.

A wide variety of pump and treat methods like chemical precipitation, adsorption, ion exchange and reverse osmosis have been trialled for many decades for fluoride removal from groundwater, but the problem of fluoride contaminated water remains in many parts of the world largely because these processes require constant monitoring, are expensive to implement and maintain at decentralised scale due to lack of reticulation infrastructure, and possess sludge disposal problem. This paper presents an overview of various fluoride removal processes and the limitations associated with each process and the application of in-situ permeable reactive barrier for remediating fluoride contaminated groundwater is explored, which displays the potential to be a cost effective, low maintenance and energy intensive technology.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.