The aim of the study was to find the effect of polyethylene (PE) coatings on the short-circuit current of silicon photovoltaic cells covered with glass, in order to improve the short-circuit current of the cells. Various combinations of PE films (thicknesses ranging from 9 to 23 µm, number of layers ranging from 2 to 6) with glasses (greenhouse, float, optiwhite and acrylic glass) were investigated. The best current gain of 4.05% was achieved for the coating combining a 1.5 mm-thick acrylic glass with 2 × 12 µm-thick PE films. This effect can be related to the formation of an array of micro-wrinkles and micrometer-sized air bubbles with a diameter of 50 to 600 µm in the films, which serve as micro-lenses and enhance light trapping.

Global climate change has induced a rise in sea surface temperature (SST), although this increase is not uniform across the world. Significant variations exist between coastal and offshore waters, particularly in regions affected by upwelling processes. This study focuses on the Canary Current Upwelling System (CCUS), stretching from Northwest Iberia to Northwest Africa. High-resolution remotely sensed SST data (0.05°) from the ODYSSEA Level 4 Sea Surface Temperature Reprocessed dataset were validated with in-situ measurements and employed to establish a regional climatological baseline for 1982 – 2012. Subsequent years were compared to this baseline to construct SST anomaly maps, revealing SST changes since 2012. The study area was further divided into sub-regions for comparative analysis. Results indicate that SST consistently increased at a higher rate offshore compared to the adjacent nearshore regions. A reference dataset spanning 1951 – 1981 was used to gauge SST variability between the two baselines. SST exhibited a 0.59°C increase from 1951 – 1981 to 1982 – 2012, with a slowing of SST trends beyond the 1982 – 2012 baseline. This research offers valuable insights into the climatological dynamics of the CCUS. These findings enhance our understanding of this critical coastal system's climatology, laying the groundwork for future investigations into evolving climate patterns in coastal regions.

This study explores the near-surface dispersion mechanisms of contaminants in coastal waters, leveraging a comprehensive method that includes using dye and drifters as tracers, coupled with diverse observational platforms like drones, satellites, in-situ sampling, and HF radar. The aim is to deepen our understanding of surface currents' impact on contaminant dispersion, thereby improving predictive models for environmental incident management, including pollutant releases. Rhodamine WT dye, chosen for its significant fluorescent properties and detectability, along with drifter data, allowed us to investigate the dynamics of near-surface physical phenomena such as the Ekman current, Stokes drift, and wind-driven currents. Our research emphasizes the importance of integrating scalar tracers and Lagrangian markers in experimental designs, revealing differential dispersion behaviors due to near-surface vertical shear caused by the Ekman current and Stokes drift. The elongation direction of the dye patch aligns with the Ekman current direction during slow current conditions. Analytical calculations of vertical shear, based on the Ekman current and Stokes drift, closely matched those derived from tracer observations. Over a 7-hour experiment, the vertical diffusivity of near-surface water was observed at 2×10-4 m2/s, and the horizontal eddy diffusivity of the dye patch and drifters reached the order of 1 m2/s and at a 1000m length scale. Particle tracking models demonstrate that while HF radar currents can effectively predict the trajectories of tracers near the surface, incorporating near-surface currents, including Ekman current, Stokes drift, and windage, is essential for a more accurate prediction of the fate of surface floats.

This study focuses on the modification of ion-exchange membranes by incorporating phosphorylated dendrimer into sulfonated polytetrafluoroethylene membranes to enhance specific selectivity between mono-/divalent ions, using the Ca2+/Na+ pair as an example. The research employs mechanical, physico-chemical, and electrochemical analyses to explore the effects of P-H20 incorporation on membrane properties. Bulk modification significantly increases membrane selectivity towards calcium ions (specific permselectivity coefficient rises from 1.5 to 7.2), while maintaining the same level of the limiting current density. Other findings indicate that bulk modification significantly changes the transport-channel structure of the membrane and alters the mechanism of over-limiting mass transfer. The over-limiting current for the pristine membrane is mainly due to non-equilibrium electroconvection, while modified membranes actively participate in the water-splitting reaction, leading to the suppression of the electroconvection. Despite this drawback, the decrease of the over-limiting potential drop results in a decrease in specific energy consumption from 0.11 to 0.07 kWh/mol. In the under-limiting current mode, the specific energy consumption for all studied membranes remains within the same limits of 0.02-0.03 kWh/mol.

it still undergoes corrosion when exposed to corrosive environments. This paper proposes an evaluation method for assessing the corrosion level of SPCC steel specimens using traditional eddy current testing (ECT), along with two different machine learning approaches. The objective is to classify the corroded state of the specimens into two states: a less corroded state (state-1) and a highly corroded state (state-2). Generative and discriminative models were implemented for classification. The generative classifier was based on the Gaussian mixture model (GMM), while the discriminative model was based on the logistic regression model. The models used features based on the absolute maximum of the perturbation magnetic field components at two different frequencies. The performance of the classifiers was evaluated using metrics such as absolute error, accuracy, precision, recall, and F1 score. The results indicate that high classification accuracy can be achieved based on both methods using traditional eddy current testing.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

This article addresses the problem of contact voltage increase caused by the low frequency oscillation of the train-grid system in the phase-separation process of the EMU. The article establishes the EMU-contact line-traction substation model, reveals the mechanism of low-frequency oscillation, and obtains the relationship between the separation phase angle of the pantograph with line and low-frequency oscillations. Methods to suppress the over-voltage during the low-frequency oscillation are proposed. The study shows that when the power phase angle of the pantograph-line separation is within the range of 60°~90° and 240°~270°, the voltage amplitude in the neutral zone is larger, the maximum amplitude can reach 52.2kV, and low-frequency oscillation will occur in the neutral zone. When low frequency oscillation occurs, the contact line voltage in the neutral zone is mainly 1/3 power frequency (16.7Hz). After installing an RC suppression device in the neutral zone, when the EMU enters the neutral zone, the absolute value of the voltage peak drops to below 20 kV. Compared with the situation where the suppression device is not connected, the absolute value of the voltage peak is reduced by nearly 60%. The study provides a basis for the design of the neutral zone of the contact line and the selection of the high-voltage equipment of the EMU.

Tellurium exhibits exceptional intrinsic electronic properties. However, investigations into the modulation of tellurium's electronic properties through physical modification are notably scarce. Here, we present a comprehensive study focused on the evolution of the electronic properties of tellurium crystal flakes under plasma irradiation treatment by employing conductive atomic force microscopy and Raman spectroscopy. The plasma-treated tellurium experienced a process of defect generation through lattice broken. Prior to the degradation of electronic transport performance due to plasma irradiation treatment, a remarkable observation emerged: in the low-energy region of hydrogen plasma-treated tellurium, a notable enhancement in conductivity was unexpectedly detected. The mechanism underlying this enhancement in electronic transport performance was thoroughly elucidated by comparing it with the electronic structure induced by argon plasma irradiation. This study not only fundamentally uncovers the effects of plasma irradiation on tellurium crystal flakes, but also unearths an unprecedented trend of enhanced electronic transport performance at low irradiation energies when utilizing hydrogen plasma. This abnormal trend bears significant implications for guiding the prospective application of tellurium-based 2D materials in the realm of electronic devices.

Noninvasive brain stimulation technique can be used for modulation of motor behaviors such as reaction time (RT). The main aim of this study was to investigate whether RT during a sequential visual isometric pinch task (SVIPT) can be affected by anodal transcranial direct current stimulation (a-tDCS) over three different stimulation sites such as dorsolateral prefrontal cortex (DLPFC), primary motor cortex (M1) or posterior parietal cortex (PPC). We also aimed to assess if stimulation of these cortical sites affect the transfer of learning during SVIPT. A total of 48 right-handed healthy participants were randomly assigned to one of the four a-tDCS groups: 1) left M1, 2) left DLPFC, 3) left PPC and 4) sham. A-tDCS was applied concurrent with SVIPT in which the participants were precisely controlled their forces to reach seven different target forces from 10 to 40% of maximum voluntary contraction (MVC) presenting on a computer screen with right dominant hand. Four test blocks were randomly performed at baseline and 15 min after the intervention including sequence and random blocks with either hand. Our results showed significant differences between a-tDCS groups on ratio RT in the sequence blocks of both the right trained (P = .041) and left untrained hands (P = .023) for target forces of 15% and 30 % of MVC, respectively. In sequence blocks, M1 showed significant elongation in ratio RT for the target force of 15% and 30 % MVC compared to PPC and Sham groups in the right hand. In sequence blocks with left hand, this negative effect were found between M1-DLPFC and M1-Sham groups. In random blocks, no significant differences were found among four groups at each target forces for the left hand while there were significant differences for 15% (P =. 04) and 40% MVC (P =. 035) in the right hand. Our findings suggest that three different stimulation sites (DLPFC, M1 or PPC) were differentially affected by a single session of a-tDCS at some target forces during SVIPT. The effects of a-tDCS on ratio RT were transferred in the left untrained hand for sequence blocks but not random blocks. Further research is needed to understand fundamental aspects of these main areas of the brain on temporal processing in a precision control task such as SVIPT.

The paper presents the methods of assessing the technical condition of varistor surge arresters used in laboratory tests and in operation - performed without disconnecting the arresters from the network. The analysis of diagnostic methods was supplemented with the results of measurements of the leakage current of arresters coming directly from production and used in the power industry. Among the available methods of evaluating the technical condition of arresters, mainly indicator solutions (temperature, operation counter) and using the measurement of selected parameters of the leakage current are used. In the latter, the method of determining the resistive component of the leakage current, determined on the basis of the analysis of voltage and current waveforms, or only the arrester current, has become widespread. In this type of measurements, current clamps are used in operation, and additionally in voltage measurements from voltage transformers, where you have to take into account the fundamental, additional sources of errors discussed in the article. These errors and dispersion resulting from the production technology may fundamentally hinder the proper assessment of the technical condition, hence it is so important to properly recognize the listed basic sources of measurement uncertainty. In addition, the analysis should take into account three factors related to external conditions - temperature, voltage applied to the arrester and the content of higher harmonics in the supply voltage for which appropriate methods have been provided to determine the active component of the leakage current for reference conditions.

This article introduces the design and analysis of a slope detection circuit tailored for on-chip sensing of the load current in DC-DC converters. The novel indirect sensing approach is grounded in measuring the output voltage slope across the filtering capacitor during discharge phases. Consequently, this slope data can be effectively harnessed to control the converter switches. The slope detector circuit was designed in standard 65 nm CMOS technology using the nominal supply voltage of 1.2 V and can be used for current sensing within the range from one to hundreds of mA. Since the proposed circuit has mainly digital character, the robustness to process, temperature and supply voltage variations can be ensured rather conveniently.

Usually, the vector control of the induction machine (IM) is done by using cascade control structures with conventional linear PI controllers, the inner loop being designed for current control, and the outer loop for rotor flux and speed control. In this paper, starting from the dq model of the IM with the rotor magnetic flux space vector aligned along the d axis, advanced control algorithms are proposed for the two control loops of the cascade structure. For the current inner loop, after the decoupling control of the two dq currents, predictive algorithms with constraints are used to control and limit the currents. Since the outer loop has a nonlinear affine multivariable plant model, a homotopy-based variant of feedback linearization is used to obtain a non-singular decoupling matrix of the feedback transformation even when the rotor flux is zero at the start-up of the motor. During the continuous variation of the homotopy parameter, the model of the plant is variable, in which case the model free algorithms are properly used to control the flux and speed of the IM. The comparative analysis obtained for the cascade structure with conventional PI controllers and advanced algorithms, respectively, shows that the last lead to improve the dynamical performance of the IM.

. The impedance change of an induction coil surrounding a metal tube adapter is investigated by the truncated region eigenfunction expansion (TREE) method. Conventional TREE method is inapplicable to this problem as a consequence of the numerical overflow of eigenfunctions of the air-metal multi-subdomain regions. The difficulty is surmounted by a normalization procedure for the numerical eigenfunctions obtained from the finite element method (FEM). Efficient algorithm is devised by the Clenshaw-Curtis quadrature rule for integrals involving the numerical eigenfunctions. Numerical results of the TREE and FEM simulation coincide very well in all cases, and the efficiency of the proposed method is also confirmed.

Abstract Introduction: In the last thirty years, brain neuromodulation techniques have been used as an alternative to pharmacological treatment of neurological disorders. Parkinson's disease (PD) is a neurodegenerative disorder leading to bradykinesia, rest tremor, postural changes, and non-motor symptoms such as depression, anxiety, sleep disorders, pain, and cognitive decline that compromises executive functions (EFs), responsible for the orderly execution of behaviors and tasks of daily life and intentional and directed actions. To this date, a few studies with transcranial direct current stimulation (tDCS) have shown beneficial effects in PD patients concerning specific motor and non-motor symptoms, targeting the motor cortex and/or prefrontal regions. Objective: The main objective of this study was to evaluate the effects of left prefrontal tDCS across a broad spectrum of motor and non-motor symptoms of PD using established validated scales. Method: Single-blind randomized clinical trial with 18 volunteers with PD, aged between 45 and 80 years (66.1 ± 9.65), who met inclusion and exclusion criteria. Participants were submitted to assessments of motor and non-motor functions employing psychometric scales and tests to evaluate EFs and were randomly divided into two groups: control (sham stimulation) and experimental (active stimulation). All participants were involved in three separate tDCS sessions. The anode was positioned over the left dorsolateral prefrontal cortex and the cathode over the right supraorbital region, with a direct current intensity of 2mA, lasting 20 minutes. At the end of the three sessions, all participants were reassessed. Results: Significant effects of tDCS on non-motor functions were observed for cognition (verbal fluency of actions, clock copy test, appointment by visual confrontation, and verbal memory with immediate free recall) and subjective assessment of sleep quality (overall restlessness and discomfort in the arms and legs at night, leg and arm cramps at night and distressing dreams). There was also an improvement in the rate of errors and successes for congruent and incongruent stimuli of the Stroop Test. The beneficial effects on motor function were decreased rigidity, improved gait, and greater agility in the finger-tapping test. Conclusion: Three tDCS sessions showed positive results for participants with PD, producing significant improvements in various motor and non-motor functions, including sleep quality, cognition, and EFs. Additionally, the present results indicate that tDCS neuromodulation of the left dorsolateral prefrontal cortex region is feasible, safe, and provides significant objective benefits for PD patients.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

This article presents a harmonic analysis of the stator currents of a squirrel-cage in-15 duction motor fed by a voltage source inverter with PWM space vector control (SV-PWM). The 16 influence of PWM switching frequency and dead time (dead-band) of controlled transistors on 17 THD and electromagnetic torque ripple is shown. The aim is to determine the lowest switching 18 frequency of the transistors for which the drive will operate correctly. Characteristics were de-19 termined as functions in the form of THD ( ), where the least square approximation was 20 used for stator current measurements when the PWM switching frequency is changed. The ap-21 proximations were realized for simulation and experimental results. To clarify the results, the 22 operation of hardware PWM circuits in microcontrollers was analyzed.

In this paper, based on the pseudo-totem pole (PTP) circuit, a family of five-level PTP dual boost converters (PDBC) is proposed. Dual boost converter has some unique advantages such as no bridge arm shoot-through risk and no switch body diode reverse recovery problem, so that it has a good application prospect. Compared with conventional three-level PTP converters, PDBCs has higher power density, higher efficiency, and low voltage and current stress. The topological derivation process, working principle, modulation and strategy of the topology are analyzed firstly. Further, the number of power devices, the switches voltage and current stress of the proposed topology is analyzed. Finally, a representative five-level PDBC experimental prototype is designed with AC input 220V/50Hz, DC output 400V/1kW, and peak efficiency of 98.27%. The experimental results show that the five-level PDBC proposed in this paper has higher efficiency and verify the correctness of the topology.

A two-layer Fe-Cr-Al-Zr surface alloy was synthesized on a zirconium substrate by magnetron sputtering and subsequent low-energy high-current electron-beam (LEHCEB) processing. Thicknesses of the top Fe69Cr20Al11 (at.%) relatively large-grained (~1 µm) and transition Fe-Zr Cr-Al amorphous layers were about 0.7 and 0.6 µm, respectively. In turn, the amorphous layer consisted of two Fe64–54Zr8–22Cr21–17Al8–7 and Fe40–16Zr42–78Cr12–4Al6–2 (at.%) sublayers, differing in both zirconium and iron concentrations in wide ranges, which were separated by another nanocrystalline interlayer. The Fe-Cr-Al-Zr surface alloy serve as a diffusion barrier, preventing interaction of the zirconium substrate with oxygen from an environment. It was thermally stable up to ≈1173 K.

Bond Properties were performed on Ag-2.35Au-0.7Pd-0.2Pt-0.1Cu alloy wire with a diameter of 25 µm under different process parameters. Effects of electrical flaming off (EFO) current and EFO time on deformability of the free air ball (FAB) were investigated using scanning electron microscopy (SEM) as well as the effects of ultrasonic power and bonding force on the bond characteristic. The experimental results showed that, FAB grows from a preheated tip to a small ball, a regular ball and finally to a golf ball with increasing either the EFO current or the EFO time, and the FAB presented optimal shape at 25 mA and 650 μs. Moreover, a nonlinear relationship between FAB diameter and EFO time is obtained at the EFO current of 25 mA, which could be expressed by a cubic equation. Further, at a constant bonding force, as the ultrasonic power increased, the mashed ball diameter grew larger and larger, the capillary hole imprint became more and more obvious, and the tail width also increased larger and larger, and vice versa. The optimal ultrasonic power and bonding force are 70 mW and of 45 gf for ball bond and 90 mW and 75 gf for wedge bond, respectively. Finally, for all the bonded wire samples prepared under optimal process parameters, no ball and wedge bond lifts happened after destructive pull test, and full intermetallic compound coverage with perfect morphology occurred on the bond pad after ball shear test, which meant that the bonded wire samples have high bond strength, and hence improved the reliability of microelectronic products.

Transcranial direct current stimulation (tDCS) is acknowledged for its non-invasive modulation of neuronal activity in psychiatric disorders. However, its application in insomnia research yields varied outcomes depending on different tDCS types and patient conditions. Our primary objective is to elucidate its efficiency and uncover the underlying mechanisms in insomnia treatment. We hypothesized that anodal prefrontal cortex stimulation activates glutaminergic projections from the infralimbic cortex (IL) to ventrolateral preoptic area (VLPO) to promote sleep. After administering 0.06 mA of electrical currents for 8 minutes, our results indicate significant non-rapid eye movement (NREM) enhancement in naïve mice within the initial 3 hours post-stimulation, persisting up to 16-24 hours. In the insomnia group, tDCS enhanced NREM sleep bout numbers during acute stress response and improved NREM and REM sleep duration in subsequent acute insomnia. Sleep quality, assessed through NREM delta powers, remains unaffected. Interference of the IL-VLPO pathway, utilizing designer receptors exclusively activated by designer drugs (DREADDs) with the cre-DIO system, partially blocked tDCS's sleep improvement in stress-induced insomnia. This study elucidated that the activation of the IL-VLPO pathway mediates tDCS's effect on stress-induced insomnia. These findings support the understanding of tDCS effects on sleep disturbances, providing valuable insights for future research and clinical applications in sleep therapy.

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

We report on the study of the temperature dependence of the response of a BSO crystal based polarimetric current sensor with spectral interrogation. Two possible interrogation schemes are discussed. The spectral dependence of the optical rotation along the crystal caused by temperature and current changes has been investigated and approximate dependences for the sensitivities to current SI and temperature ST have been derived. A mixed term in the response with spectral interrogation has been revealed, the elimination of which is done by tracking wavelength shifts of two distinct extrema in the polarimetric response. A temperature independent second degree equation for the current changes as a function of the spectral shifts has been derived and tested.

Short-range Internet of Things (IoT) sensor nodes operating at 2.4 GHz need to provide ubiquitous wireless sensor networks (WSNs) with energy-efficient, wide-range output power (POUT) and fully integrated on a single chip for wireless body area networks (WBANs) and wireless personal area networks (WPANs) using low-power Bluetooth (BLE) and Zigbee standards. The proposed fully integrated transmitter (TX) utilizes a digitally controllable current-mode class-D (CMCD) power amplifier (PA) with a second harmonic distortion (HD2) suppression to reduce VCO pulling in an integrated system while meeting harmonic limit regulations. The CMCD PA is divided into 7-bit slices that can be reconfigured between differential and single-ended topologies. Duty cycle distortion compensation is performed for HD2 suppression, and an HD2 rejection filter and a modified C-L-C low-pass filter (LPF) reduce HD2 further. Implemented in a 28 nm CMOS process, the TX achieves a wide POUT range of from 12.1 to -31 dBm and provides a maximum efficiency of 39.8% while consuming 41.1 mW at 12.1 dBm POUT. The calibrated HD2 level is -82.2 dBc at 9.93 dBm POUT, resulting in a transmitter figure of merit (TX_FoM) of -97.52 dB. Higher order harmonic levels remain below -41.2 dBm even at 12.1 dBm POUT, meeting regulatory requirements.

Abstract: High power semiconductor laser is a kind of photoelectric device with high efficiency and high stability, the performance of its drive system directly affects its output characteristics and service life. In order to solve the problems of stability and robustness of the output power of semiconductor laser, a semiconductor laser driving power supply with high efficiency, low ripple and strong anti-interference ability was developed. The power supply adopts full-bridge LCC resonant power topology. Firstly, a mathematical model is established to analyze the relationship between LCC resonator parameters and output current gain. Secondly, a LCC resonator parameter design method is proposed to reduce the current stress of components, and the variable frequency phase shift (PFM-PWM) composite control strategy and linear active disturbance rejection control (LADRC) algorithm are proposed, which not only ensures the zero voltage (ZVS) conduction of MOS tube, but also reduces the on-off loss of MOS tube. Improved power efficiency and suppressed output current ripple; At the same time, the instability of the output current is ensured due to the input voltage, load and parasitic parameter change of the circuit. Finally, the simulation and experimental results show that the power supply can be continuously adjustable in the output current range of 0-40A, the current ripple is less than 0.8%, and the working efficiency is up to 92%. It has the characteristics of high stability, small ripple, high efficiency, low cost and good robustness.

Article contents the analytical model of the drift of a separate ice field under action of wind and current, which velocities and directions can vary during time. Model takes into account the mass of ice, added mass of sea water and the effects of the wind and current on the ice field in form the friction on its upper and underwater surfaces and frontal resistance on its end (forward and backward) surfaces. Results of performed the steady wind drift of the ice fields modelling show the drift velocity exceeds considerable known velocity of a compact ice cover wind drift. Drifting ice field has the certain kinetic energy that should be released when collision with unmovable obstacle and spent on brittle breakdown of part of the ice field. Volume of formed small ice pieces (fragments of ice field) was estimated by comparison of the specific energy of the sea ice brittle destruction and the kinetic energy of drifting ice field. Article presents the results of estimation of possible volume of the ice pieces and the scales of formed piles as result of collision with an obstacle depending on initial dimensions of ice field and wind speed. Developed models and the results of computer modelling can be used to estimate the ice pile sizes near the stationary platforms and terminals on the Arctic seas.

So far, scientific studies on high frequency welding (HF) have observed the three main parameters: anode current, welding time and pressure of upper electrode. Some authors have also observed and studied the welding frequency, the power, and the values of the dielectric constants of the materials or the angle of dielectric losses. Due to the complex effects that the parameters have on the quality of the welded joint, it is necessary to extend the research and study the mutual relationships between a large numbers of process parameters on the welded joint in order to achieve satisfactory strength of the welded joint. In this research, the number of considered parameters is increased to 17, each of which is relevant to the processes of HF welding, and their mathematical equations are presented. The research is carried out on a HF welding machine improved with a linear pneumatic actuator for lowering the upper electrode and regulating the compressive force, and a measuring machine with the appropriate measuring method for determining the breaking forces with a tension gage and performing the „T“ test is made. Numerous researches were carried out on the functional changes of the process parameters of the percentage share of the values of the coupling capacitor, the anode current and the welding time on the values of the breaking forces of the welded joints. Based on the conducted research, it was concluded that the optimization of the process parameters of HF machine must be performed before the welding process, which is determined by a certain amount of energy that must be introduced into the material. These parameters are the capacity of the output capacitor, i.e., the value of the electric current flowing through the material and the time for the development of the operating power to produce welded joints with a certain strength and quality of welded joints for a specific material used in the process.

Neutral beam injection (NBI) is used for thermonuclear plasma heating, non-inductive current drive, rotation, operation scenario control, and for plasma diagnostics in nuclear fusion devices. NBI is the main source of fast particles in plasma which transmit energy to thermal plasma during their slow-down. Steady-state tokamak operation is only possible when the sub-thermal particles energy is absorbed and effectively confined in plasma volume. While NBI purposes and applications vary through different fusion systems, the engineering tasks performed during research and development (R&D) stage of neutral beamline design have much in common. The NBI studies, especially addressing long pulse and high-power operation typically include a beam transmission analysis and power loads distribution at the structural components of the beamline. Thermo-structural analysis is applied next to heat removal circuits design. ‘Beam Transmission’ (BTR) code is a dedicated tool, developed by a physicist and used by NBI physicists and engineers. BTR was created and 1^st applied during R&D phase of the world’s largest tokamak ITER. BTR code is intended for public usage and routinely applied for detailed simulations of neutral beam propagation through complex beamlines. BTR is flexible and intuitive in input, user-friendly and fully interactive. Thanks to visualization and high performance BTR looks and feels like a real NB flight simulator. Despite BTR ‘mature’ age, the code is still in evolution. Support is available to all new BTR users.

The design of a mixed-mode proportional-integral-derivative (PID) controller circuit using current-feedback operational amplifiers (CFOAs) as active components is proposed. With the same circuit topology, the proposed configuration of three CFOAs, four resistors, and two capacitors is capable of performing the PID controller in all four operation modes: namely voltage mode, trans-admittance mode, current mode, and trans-impedance mode. Numerous mathematical analyses are conducted to determine the controller performance under ideal and non-ideal conditions. Additionally, the mixed-mode second-order lowpass filter is suggested, and also used to examine the workability of the proposed mixed-mode PID controller in a feedback control structure. The proposed PID controller is implemented with the commercially available IC-type CFOA AD844, and the simulation results are presented to illustrate the functionality of the controller and its closed-loop control system.

Smart grids are seeing an increase in renewable energy and an enormous introduction of advanced power electronics, increasing the number of disturbance sources. This requires improving the accuracy of measurement systems capable of acquiring data for use in power system monitoring applications. Rogowski Coils (RCs) and Merging Units (MUs) are being widely deployed in controlling, metering, and monitoring of digital power systems. Because the performance of digital measurement devices has a direct influence on power measurement accuracy, it is critical to perform a laboratory calibration of these measurement instruments before they are installed in any project. To determine the magnitude and phase displacement errors of the RC+MU under normal and abnormal operating conditions, this article presents a comprehensive laboratory digital calibration system constructed from precise, readily available commercial products such as a fluxgate current transducer and a National Instrument. In addition, the analysis of measurement chain is affected by sources of uncertainty is discussed. The tests yield findings that are consistent with the relevant standards.

We report on ground-based measurements of the atmospheric electric field (Ez= -Potential Gradient (PG)) and current density (Jz) that were conducted at two locations in Israel. One is the Emilio Segre cosmic ray station located on Mt. Hermon (34.45 N, 2020 m AMSL) located in northern Israel near the Syrian-Lebanon border and at the other at the Wise astronomical observatory in the Negev desert highland plateau of southern Israel (31.18 N, 870 m AMSL). We searched for possible effects of strong, short-term solar events on the potential gradient and the vertical current density, as disruption to the Global Electric Circuit are often observed following strong solar events. The first case study (St. Patrick Day, 17 March 2015) was classified as the strongest event of 2015. The second case study (8 Sep 2017) was categorized as the strongest event of 2017 and one of the twenty strongest events on record to date. The results show that the electrical parameters measured at ground level at both stations were not affected during the two massive proton events and the ensuing geomagnetic storms. The magnetospheric shielding in lower latitudes is strong enough to shield against flux of energetic particles from solar events, obscuring any impact that may be noticeable above the local daily variations induced by local meteorological conditions (aerosol concentrations, clouds, high humidity, and wind speed) which were investigated as well.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Insulated Gate Bipolar Transistor (IGBT) may convey high current and sustain high breakdown voltages; it may provide high power control. In a sense, how IGBT demonstrates the capability of power control was not specifically described, and the equivalent bipolar junction transistors (BJT) activated by an applied bias to the insulated gate is intriguing. As seen in Figure 1, IGBT shows an equivalent circuit structure containing two types of BJT, (NPN-type Bipolar transistor and PNP-type Bipolar transistor), which can be modeled as diode-associated transistor. Apparently, as a bias applies to the controlling gate, the channel beneath the gate oxide gets strongly inversed and turns out to be conductive just like what happens on metal-oxide-silicon field effect transistor (MOSFET), which provides necessary igniting currents to both BJTs and thus causes high current gain flowing through them-selves from the bottom. A proposed and renewed formula provides addressing the above scenario and successfully fitting the measured data that forms the characteristic curves. Some parameters in the proposed formula, which includes size and mobility associated constant, threshold voltage, and Early-Voltage-related lambda for MOSFET, explain and explore the underlying physics. IGBT thus enjoy high input impedance and high current gain due to MOSFET (Insulated Gate) and BJT, respectively. This formula combines both merits of MOSFET and BJT in order to fit the measured data. Indeed, the formula intimately fits IGBT electrical characteristic curves, and thus may be qualified and served as a model. The new model is then advisable for designing power integrated circuit to exactly achieve power saving, power control, and power efficiency.

: In the automotive industry, high-strength plates have been increasingly used to reduce the vehicle body weight due to stringent regulations on fuel economy and safety. Such plates achieve tensile strengths as high as 1.5 GPa owing to the hot-stamping process. However, these plates suffer from scale generation and surface decarburization because of the surface oxidation of the material. Recently, studies on materials subjected to high-frequency induction heating have reported strength improvement owing to the coil shape and cooling method. This study presents the surface temperature changes, mechanical properties, and microstructures of boron steels subjected to longitudinal heating, which uses eddy currents generated from high-frequency induction heating. The surface temperature data were analyzed under different high-frequency induction heating powers (15, 18, 21, 24, 27, and 30 kW) and distances from the specimen (6, 9, and 15 mm). The mechanical properties and microstructures were also analyzed in different high-frequency induction heating coil directions. The correlations between the high-frequency induction heating power and the distance from the specimen with the maximum tensile strength were determined.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

Here we present calculation of the critical current of DC SQUID based on the Josephson junction on multi-band superconductor with frustration effect. It is shown that the changing of the critical current of DC SQUID with small geometrical inductance is determined by the ratio of supercurrent amplitude in different channels and the external magnetic field. In the a case of DC SQUID with high inductance frustration effects can be ignored.

Exposure to quasi-electrostatic field induced currents is a hazard of live-line transmission work. These steady-state induced currents are typically less than 1 mA, and their sensory effects range from imperceptible to painful depending on the person and conditions such as contact area and duration. Permanent injury from these currents is unlikely but they can distract workers, increasing the risk of injury from falls or other dangers. Identifying contact current severity and training workers can help reduce risk of accidents. Measuring induced currents along a climbing route is time consuming and simulation is challenging because of geometric complexity of the worker, transmission structure, conductor bundles, and electric fields in the climbing space. This research explores calculation of worker contact current using a recently developed adaptation of the charge simulation method. The method uses Fourier principles to improve computational efficiency when explicitly modeling all bundle subconductors. The research also examines reasonable simplifications for modeling lattice structures and human geometry. Calculated results compare well to measured currents for a worker climbing a 400 kV lattice structure. This indicates the method is a practical option for calculating the severity of steady-state contact currents. A simple calculation is suggested for estimating these currents.

Permanent magnet brushless DC motor (BLDCM) is usually controlled by six step commutation method, and flux-weakening method is used to make the motor run higher above the base speed. For now, it is considered that the weak magneto-electric angle range is 0-pi/3, and that of deep weakening is pi/3-pi/2. In the field- weakening control, the forward shift of commutation point will form inverter circulating current in the three-phase bridge of inverter and the stator winding of the motor. In this paper, the principle of inverter circulating current formed by inverter is analyzed. Through magnetic potential analysis and Simulink simulation, it is concluded that flux-weakening control will generate inverter circulating current in the inverter and motor stator winding. The inverter circulating current affects the magnetic potential of motor, and magnetic potential will move to the rotating direction of motor rotor. When the forward shift angle of inverter commutation point is 0-pi/6 electrical angle, the movement amplitude of current circulating current of inverter is less than pi/6, which plays the role of weakening magnetic field and driving effect; when the forward moving angle is pi/6-pi/3, the movement amplitude of inverter circulating current exceeds pi/6, which plays the role of magnetic weakening and braking. When the braking effect occurs, the reverse torque will appear, resulting in the decrease of motor torque and efficiency. Therefore, the range of weak magneto-electric angle should be between 0-pi/6.

Optical current sensors have been developed and improved in recent decades, and their use has been widespread in power systems, including smart grids. Like any measuring instrument or system, the result of its measurements is associated with a measurement uncertainty, which quantifies its precision. This article presents a review of the main uncertainty contributions that affect the quality and performance of optical current sensors.

A hypothesis that the generally accepted value of the LiPON conductivity should be attributed to the absorption and displacement currents is substantiated. The reason is a small contribution of the drift current due to field screening by the electric double layer. The basis for this assumption is the measurement of the LiPON absorption capacitance, according to which its dielectric constant is about 106. An alternative equivalent circuit containing a non-ideal absorption element is proposed and its impedance is calculated. It is shown that the Bode diagrams of the alternative circuit well approximate the experimental curves. Parameters and the magnitude of electric field screening are calculated basing on proposed model of a double electric layer. Considering the screening effect, the drift conductivity of LiPON is obtained, which value is in good agreement with the data on lithium concentration and mobility.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Hip fractures are the most frequently treated fractures in the world. Of these, intertrochanteric fractures (ITFs) account for almost 50%. After surgical fixation of ITFs, nonunion is rare. Nonunions are commonly produced from mal-reduction (in varus) and/or inadequate stability of the bone-implant construct and/or fatigue failure of the implants. Other causes of nonunion include posteromedial comminution and osteoporosis. The published incidence of ITF nonunion is 1%-2%. Mechanical complications of ITFs include cut-out, excessive shortening of the proximal femur, delayed union, nonunion, early implant fracture, nail toggle and cut through/medial migration. That is why a fundamental goal in the treatment of ITFs is to achieve stable fixation in osteoporotic bone, allowing early weight bearing. Intraoperative determination of fracture stability is essential. The American Academy of Orthopedic Surgeons (AAOS) clinical practice guidelines for the management of intertrochanteric fractures (ITF) in patients older than 55 years are the following: 1) In patients with stable ITF, the use of either a sliding hip screw (SHS) or a cephalomedullary nail (CMN) is advised (strong strength of evidence). 2) In patients with reverse obliquity fractures, a CMN is recommended (strong strength of evidence). 3) Patients with unstable ITF should be treated with a CMN (strong strength of evidence). 4) In patients with ITF, a short or long CMN may be considered (limited strength of evidence).

The performance of Yttrium-Barium Copper Oxide (YBCO) high-temperature superconductors in high-frequency applications is significantly affected by the microwave surface resistance (Rs). The paper delves into the basics, measuring methods and factors affecting the resistance (Rs) in YBCO, highlighting its high critical temperature (Tc) and low resistance, positioning it as a promising material. YBCO's compatibility with epitaxial growth and microstructure engineering offers opportunities to reduce grain boundary effects and improve Rs, making it advantageous for high-frequency electronics, communication systems, and MRI coils. This is due to its high critical current density (Jc) and exceptional Rs at practical temperatures. Challenges remain in comprehending and managing Rs in YBCO, despite its favorable characteristics. Utilizing advanced fabrication methods and incorporating nanotechnology allow for customization of YBCO-based devices. Multi-scale modeling and simulation are essential for guiding experimental work and understanding YBCO's performance in high-frequency settings. This study highlights the promise of YBCO for future high-frequency technologies and stresses the importance of more research to overcome hurdles and fully exploit its capabilities, potentially transforming superconducting devices for practical use.