Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

The current study assessed the influence of Anti Stripping Agents (ASA), Ground Tire Rubber (GTR) and waste polyethylene terephthalate (PET) on performance behavior of binder and Stone Matrix Asphalt (SMA) mixtures. Through this paper, the 85/100 penetration grade bitumen was utilized as original bitumen. Also, three liquid ASA’s (ASA (A), ASA (B), ASA (C)) were used as a mixture modifier. For this purpose, softening point, penetration, rotational viscosity, Dynamic Shear Rheometer, Multi Stress Creep Recovery (MSCR) and Linear Amplitude Sweep (LAS) tests were implemented to investigate the rheological properties of modified bitumen. For evaluating the behavior of modified mixtures several tests such as; Resilient Modulus, Tensile Strength, dynamic creep, wheel track and four-point beam fatigue tests were implemented. Based on MSCR test results, utilization of mentioned polymers enhanced the elasticity of bitumens and therefore the permanent deformation resistance of binders increases. Also by the addition of PET percentage, the rutting resistance improves. Results indicated that utilization of ASAs, PET and Crumb Rubber (CR) enhance the Resilient Modulus (Mr), Indirect Tensile Strength (ITS), rutting resistance, fatigue life and Fracture Energy (FE) of asphalt mixtures. Also based on results, modification of binder by PET/CR with a ratio of 50%/50% and ASA (B) have the highest fatigue life which indicates that this mixture has highest resistance against fatigue cracking.

The unquenchable demand for rock materials has attracted many companies within the building and construction sector to invest in stone quarrying. However, this has brought about the environmental impacts with health threats to people. There is a paucity of information about the magnitude of pollution on air and water and how it varies with quarry sites. This study therefore investigated the physical impacts of quarrying on air and water and explored the in-situ mitigations to undesirable effects due to stone quarrying. Four active quarry sites were identified. Field measurements of dust (particulate matter) was conducted within the four quarry sites and in the nearby community. Water samples were collected from quarry pits and nearby shallow wells for laboratory analysis of water quality. Statistical Analysis of Variance (ANOVA) was used to test for differences in pollution across the four studied sites. Results revealed that, amidst use of wet crushing and water sprinkling on bare surfaces, dust emission was higher than the recommended permissible standards levels with a significant variation across the quarry sites with ANOVA (P-value=0.003) for PM2.5 and (P-value=0.04366) for PM10. Water pollution was mainly contributed by the non-permissive levels of nitrates, chromium, and pH. Polluted air and water are associated with sparking off health threats to the users in the community. In conclusion, quarry companies should strengthen the already existing mitigation of dust suppression. The study recommends additional measures such as treating quarry pit water before discharging to the open environment

The development of innovative materials is one of the most important focuses of research in heritage conservation. Eligible materials can not only protect the physical and chemical integrity of artworks, but also preserve their artistic and aesthetic features. Recently, as one of the hot research topics in materials science, biomimetic superhydrophobic materials have gradually attracted the attention of conservation scientists due to their unique properties. In fact, ultra-repellent materials are particularly suitable for hydrophobization treatments on outdoor artworks. Owing to their excellent hydrophobicity, superhydrophobic materials can effectively prevent the absorption, penetration of liquid water as well as the condensation of water vapor, thus greatly relieving water-induced decay phenomena. Moreover, in presence of liquid water, the superhydrophobic surfaces equipped with self-cleaning property can clean the dirt, dust deposited spontaneously, thereby restoring the artistic features simultaneously. In the present paper, besides the basic principles of wetting on solid surfaces, materials and methods reported for preparing bioinspired ultra-repellent materials, the recently proposed materials for art conservation are also introduced and critically reviewed. Lastly, the current status and the problems encountered in practical application are also pointed out, and the focus of future research is prospected as well.

In a bandsaw machine the blade guides provide additional stiffness and help to align the blade near the cutting region. Typically these are either in form of blocks made of carbide or ceramics or as sealed bearings. Abrasive particles, generated while cutting hard and brittle materials like natural stones, settle between the contact surfaces of the guides and the blade causing wear and premature failure. The hydrostatic guide system as presented in this work, is a contactless blade guiding method that uses force of several pressurized water jets to align the blade to the direction of the cut. For this investigation, cutting tests were performed on a marble block using a galvanic diamond coated bandsaw blade with the upper roller guides replaced by hydrostatic guides. The results show that the hydrostatic guides help to reduce the passive force while cutting to a constant near zero in contrast to the traditional guides. This also resulted in reduced surface roughness of the stone plates that were cut indicating a reduction in lateral vibration of the band. Additionally, it has also been shown that using hydrostatic guides the bandsaw blade can be tilted to counter the bandsaw drift opening opportunities for further research in active alignment control. This original research work has shown that the hydrostatic guide systems are capable of replacing and in fact perform better than state of the art bearing or block guides particularly for stone cutting applications.

Food intake plays a pivotal role of human growth, which necessarily contributes 45% of global economy and wellbeing in general. Consumption of balanced food is elementary for overall good health while a shift of equilibrium can lead to malnutrition, prenatal death, obesity, osteoporosis and bone fractures, coronary heart diseases (CHD), idiopathic hypercalciuria, diabetes and many more. Though CHD, osteoporosis, malnutrition, obesity are being classified thoroughly in the literature, there are fragmented findings in the regime of kidney stone diseases (KSD) and the correlation with food intake therein. KSD associated with hematuria and renal failure poses an increasing threat to the healthcare and global economy while its emergence of Indian populations is being affected with multi-factorial urological disorder resulting from several factors. In this realm, epidemiological, biochemical, macroeconomic situations been portrayed when food intake is also a paramount importance which rarely been forecasted. Hence, in this article we will be reviewing the corollary connotation with diverse food consumption and the efficacy it plays in KSD extrapolating in Indian context.

Background: Work experience is a key factor that influences safety awareness among workers. This study investigated the influence of work experience on the level of awareness on adverse health effects of silica dust exposure among stone quarry workers in Ghana while controlling for theoretically relevant compositional and contextual factors, evaluated the magnitude and order of association between the predictors and the predicted variable. Method: A cross-sectional survey data of 524 randomly selected stone quarry workers were subjected to multivariate statistical analyses. Results: Stone quarry workers who had 6 to10 years and more than 10 years of work experience were 48% (OR = 1.475, P = 0.021) and 82% (OR = 1.816, P = 0.003) respectively more likely to be aware of the adverse health effects of silica dust exposure compared to their counterparts who had 1 to 5 years work experience. Workers who had secondary or higher education were 32% (OR = 1.320, P = 0.036) more likely to be aware of the adverse health effects of silica dust exposure compared to their counterparts who had no education. Conclusion: These findings provide relevant information for managers and policymakers to plan and maximize awareness on silica dust health hazards among silica exposed workers.

Aim: Aim of our study to evaluate various factors responsible for surgical site infection after gastrointestinal and hepatobiliary surgeries. Material and Methods: Patient who underwent gastrointestinal and hepatobiliary surgery in our department were evaluated retrospectively. Various factors associated with surgical site infection were evaluated using univariate and multivariate analysis. Surgical site infection was defined as any culture positive discharge from the wound within 30 days of surgery.Statistical analysis was done using SPSS version 23. Results: We evaluated total 331 patients operated between April 2018 to March 2020. 14 patients were lost to follow up after discharge and before completing post operative day 30. 18 patients expired before 30 days without developing SSI and were excluded from the study as per exclusion criteria. 299 patient included in the study. Total 20 patients developed surgical site infection. It showed SSI rate in our study population was 6.68%. On univariate analysis prolonged hospital stay, more blood product used, higher cdc grade of surgery, higher ASA grade, more operative time, open surgeries,colorectal and HPB surgeries were associated with surgical site infections. On multivariate analysis only prolonged hospital stay independently predicted Surgical Site Infectins. (p=0.014,0dds ratio 1.223, 95% confidence interal 1.042-1.435). Conclusion: Prolonged hospital stay independently predicts surgical site infections after gastrointestinal and hepatobiliary surgery.

In general, the stone pagoda structures with discontinuous surfaces are vulnerable to lateral forces and are severely damaged by earthquakes. After the Gyeongju earthquake in 2016 and the Pohang earthquake in 2017, the earthquakes damaged numerous stone pagoda structures due to slippage, rotation and the separation of stacked stone. To evaluate seismic resistance of masonry stone pagoda structure, we analyzed the seismic behavior of stone pagoda structure using shaking table test. Shaking frequency, permanent displacement, maximum acceleration, rocking, and sliding were assessed. Responses to simulations of the Bingol, Gyeongju, and Pohang earthquakes based on Korean seismic design standard (KDS 41 17 00) were analyzed for return periods of 1,000 and 2,400 years. We found that the type of stylobate affected the seismic resistance of stone pagoda structure. When the stylobates were stiff, seismic energy was transferred from lower to upper regions of the stone pagoda, which mainly resulted in deformation of the upper region. When the stylobates were weak, earthquake energy was absorbed in the lower regions; this was associated with large stylobate deformations. The lower part of tower body was mainly affected by rocking, because the structural members were slender. The higher part of the stone pagoda was mainly affected by sliding, because the load and contact area decreased with height.

The transition from Building Information Modelling (BIM) to Heritage Building Information Modelling (H-BIM) is intended to pursue an adequate knowledge of the artefact that is to be preserved, progressively replacing the traditional methods of the restoration and structural reinforcement projects with new tools for managing both existing information and new interventions. The aim of the paper is to show the application of the H-BIM method to a stone pavement road located in the Archaeological Site of Pompeii. In detail, starting from a Laser Scanner based survey, juxtaposed by coordinated points georeferenced through a total station, points clouds were handled by means of several BIM-based tools to perform the road design process, starting from the digital elevation model (DEM) to the corridor representation. Subsequently, a visual programming application based on Python language was adopted to update corridor information by means of the object property set. As preliminary results, a tool, complete with graphical and non-graphical information, is proposed to be used in conservation, maintenance and restoration project.

In the second half of the 19th century new methods for quarrying and processing natural stone are developed. In the Nordic countries Sweden, Norway and Finland this technological pro­gress goes hand in hand with a systematic geological mapping and large-scale exploitation of natural stone deposits. As a result, new constructions are developed—changing the building practice in these countries. With the end of historicism a new architecture arises that particularly in Norway and Finland acquires a national-romantic character. This paper examines the interaction between geological exploration, commercial development, technical inventions and the development of a national-romantic architecture.

This paper takes the VR animation display of the Ming Xiao Mausoleum General stone statue life as an example to study the advantages of VR animation in the display of material heritage. Combined with literature and pictures, the digital restoration of the Ming Xiao Mausoleum stone statue is carried out in MAYA and Z brush, and the construction of the scene and the output of the final effect are realized in UE4.

The use of natural stone has a historical and environmental value that makes it strategically valuable for landscape conservation in Europe. Marble, among others, is widely spread on Earth, and it offers high-performance features in architectural applications. However, the complexity of these formations and the rock variability in different ore bodies require detailed studies of the natural and induced stress state, the fracturing degree, and the influence of external factor (such as temperature and/or chemical agents) on the mechanical properties in order to optimize the exploitation processes by reducing extractive waste. This article shows a series of studies conducted by the authors over the last 20 years aimed at making the exploitation of marble blocks in the Carrara basin safer, more efficient, and, therefore, more sustainable. In particular, studies for increasing the knowledge on the natural and the induced stress state through on-site measurements and numerical modeling, studies to improve the quality of the exploited material through improvements of cutting technologies, studies to improve the knowledge of the mechanical behavior of the material under varying loads and temperature conditions and studies to improve the reuse of water materials and their reduction are reported.

Wasted Green tuff powder produced by cutting Towada stone is recycled as environmental cleaning material. The optimum temperature for green tuff powder calcination to reduce the hydroxyl radical produced in hydrogen peroxide decomposition with ultraviolet light (UV) and no light. The green tuff calcined at 800 °C shows the large decomposition rate of hydrogen peroxide with no UV light when measured by using ESR. With UV light, the optimum temperature for calcinating the green tuff powder in order to reduce hydroxyl radical is also 800 °C. Next, the powder calcined at 800 °C is used to produce the tile by compression and heating, and then the formaldehyde adsorption rate was measured. The green tuff powder calcined at 800 °C showed a high adsorption rate, similar to that of the activated carbon. The tiles formed at 40 MPa and heated st 1100 °C were the strongest and also adsorbed formaldehyde. The adsorbed formaldehyde on the green tuff tile and powder might have a possibility to decompose by photocatalytic.

Due to limitation of natural sand from rivers and seas, artificial sand production from large stones or rocks is being increased. However, this sand manufacturing process is dangerous and causes several social problems such as high level of unwanted vibrations or noises. This study investigates vibration characteristics of sand and screen units in artificial sand production plant whose actuating operation is multiple with several different exciting frequencies. As a first step, vibration levels are measured at the sand and screen unit positions using accelerometers in time and frequency domains. The measurement is carried out at two different conditions: activating sand unit only and operating entire facilities such as stone crusher. Vibration signals acquired from several locations of the sand and screen units of the plant are collected and analyzed from waveforms and spectrums of the signals. It is identified that the vibration acceleration level of the screen unit is higher than that of the sand unit. In addition, it is found from the acceleration signals measured at plant office and shipping control center those places are far away from the plant location that the beating phenomenon is occurred by close driving frequencies for several sand units. In this work, the vibration caused from the beating is significantly reduced by adjusting the driving frequencies for the sand units so that they are sufficiently scattered to avoid the beating.

Biochar is a carbon allotrope obtained by pyrolysis of biomass, usually agro-waste. Owing to the demand for sustainable development, biochar is continuously raising much hope in the scientific community. However, in order to impart it with new properties, its modification is required, either in situ during pyrolysis, or after the carbonization process. Herein, we propose a new direct approach to obtain bimetallic copper/nickel nanoparticle-loaded on olive stone biochar. The bimetallic-coated biochar and the reference materials bare biochar, copper-loaded and nickel-loaded biochar were prepared at 400 °C under a stream of dinitrogen from olive pit powder particles impregnated first with citric acid (CA), and then with copper and nickel nitrates. We have employed citric acid in the process in order to check its effect on the structural and textural properties of biochar supporting the metallic nanoparticles. Surprisingly, citric acid induced the formation of agglomerated or even raspberry-shaped, bimetallic copper/nickel nanoparticles. Large 450-500 nm-sized agglomerates of ~80 nm bimetallic CuNi NPs were noted for B-CA@CuNi. Interestingly, for biochar material prepared with initial Cu/Ni=10 molar ratio (B-CA@CuNi10/1), the bimetallic NPs formed unusual nano-raspberries (1748 nm in size) which are agglomerates of individual 10-20 nm-sized CuNi10/1 nanoparticles. The B-CA@CuNi and reference materials were characterized by Raman spectroscopy, scanning electron microscopy (SEM)/energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and magnetometry. The B-CA@CuNi and B-CA@Ni materials could be attracted efficiently with a magnet, but not B-CA@CuNi10/1 due to a low nickel loading. B-CA@CuNi was tested as a catalyst for the degradation of methyl orange (MO). Discoloration was noted within 10 min, much faster than a similar material prepared in the absence of CA. B-CA@CuNi could be recycled at least 3 times with exhibit as fast discoloration catalysis performance. This paper stresses the important role of citric acid in shaping the bimetallic nanoparticles loaded in situ on biochar during the slow pyrolysis process and to enable faster catalysed discoloration of organic dye solution.

The article suggests methods that allow creating the most complicated type of polygonal masonry found in Peru. This masonry type consists of large stone blocks weighing from several hundred kilograms to several tons fitted close to each other almost without a gap between complicated curved surfaces over a large area. The work provides a description of techniques, which apparently were used by builders who arrived from Europe. The techniques under discussion are based on the use of a reduced clay model, 3D-pantograph, topography translator and replicas. The use of the topography translator, reduced clay model and pantograph provides not only the unique appearance and high quality of masonry of large blocks, but also allows to increase the productivity of the builders significantly. As machines coping-scaling three-dimensional objects are known since the beginning of the 18th century, the stone structures under consideration should be approximately dated by this time. The remaining simpler types of polygonal masonry, when the stones are small or the fitted surfaces are almost flat, or the stones contact each other over a small area, or there are significant gaps between the stones, are quite consistent with the well-known methods of stone processing at that time or earlier, and, therefore, they do not require any additional explanations. The Fortress Sacsayhuaman is considered as an example of early star fortresses that has survived to our time. The polygonal structures in Peru, the polygonal Face Towers and polygonal bas-reliefs in Cambodia, symmetrical statues of pharaohs in Egypt are based on the same construction technologies, working methods, tools and technical contrivances. Therefore, with a high probability one can state that all these monuments were created by the same group of architects, sculptors, builders, and could not have appeared before the 17th century.

When animals evolve sufficient intelligence and dexterity to be able to learn to fabricate utility products (UPs) like tools, the UP's they produce become part of an induced-reproduction system that intrinsically shares many life-like traits with biological organisms, including genome-like fabrication and operation information that is physically-encoded in the animal fabricator’s neural networks. When this set of life- like traits includes a sufficient capacity for system-improving cultural evolution (UP-evolvability), the UPs become ‘para-alive’, i.e., nearly alive, or a form of non-biological UP-paralife that is equivalent to the life- status of biological viruses, plasmids, and transposons. In the companion paper I focus on the evolution of UP-paralife in the context of modern, language-capable humans and its predicted evolution going forward in time (Rice 2022). Here I look backward in time and focus on the origin of UP-paralife and its subsequent coevolution with human intelligence. I begin by determining the pathways leading to the evolution of large brains in the rare lineages of biological life that have sufficient intelligence to learn to fabricate tools –a critical first step in the evolution of UP-paralife. The simplest forms of these learning- based UPs, made by species like chimpanzees and New Caledonian crows, represent only proto-UP- paralife because they lack sufficient UP-evolvability. Expanded UP-evolvability required a combination of three attributes that enabled continuous niche-expansion of the animal fabricator via a new and advanced form of UP-mediated teamwork (TW): i) self-domestication that facilitated TW among low-related individuals, ii) learned volitional words (protolanguage) that represent ephemeral UPs that coordinate TW, and iii) learned fabrication of simple flaked-stone tools with cutting and chopping capabilities (a UP to make other structural UPs) that expanded teammate phenotypes and TW capabilities. This specific triad of attributes is synergistic because each one acts as a TW-enhancer that can gradually erode different components of the three major constraints on TW operation and expansion: too much selfishness, insufficient coordination signals, and insufficient physical traits of teammates. The increase in UP- evolvability was transformative and marked the origin of UP-paralife and the initiation of coevolution between UP-paralife (cultural evolution) and the intelligence of its hominin/human symbiont (genetic evolution) that fostered 2.5 million years of: i) continuous brain size increase and niche-expansion within the genus Homo, and ii) parallel advances in the diversity, complexity and uses of UP-paralife. This coevolution also fostered evolutionary expansion of word-based communication, and eventually language, that acted in a catalyst-like manner to facilitate the evolution of increasingly complex forms of imagination, reasoning, mentalizing, and UP-generating technology. I next focus on the evolution of creativity in the human lineage –in the form of divergent thinking and creative imagination. I conclude that the evolution of this advanced cognitive feature required a preadaptation of sufficient intelligence and is the component of human cognition that was the major causal factor generating the greatly expanded diversity and complexity of UP-paralife currently associated with modern humans. Lastly, I apply my findings to the issue of the prevalence of extraterrestrial intelligent life. I conclude that any exoplanets with detected chemical life will very rarely (e.g., probability ~10-5 for a planet closely matching Earth’s characteristics) have evolved intelligence equalling or exceeding that of humans.

A quantitative method is proposed to determine of Stone-Wales defects for carbon nanostructures with sp2 hybridization of carbon atoms. The technique is based on the diene synthesis reaction (Diels-Alder reaction). The proposed method was used to determine Stone-Wales defects in the few-layer graphene (FLG) nanostructures synthesized by the self-propagating high-temperature synthesis (SHS) process, in reduced graphene oxide (rGO) synthesized based on the method of Hammers and in the single-walled carbon nanotubes (SWCNT) TUBAL trademark, Russia. Our research has shown that the structure of FLG is free of Stone-Wales defects, while the surface concentration of Stone-Wales defects in TUBAL carbon nanotubes is 1.1×10-5 mol/m2 and 3.6×10-5 mol/m2 for rGO.