The GPA is a universally recognised and utilised metric of academic performance that is considered to also measure a student’s potential for academic performance in the future. In this short communication we examine to what extent the GPA of the first grade of high school predicts performance in the later grades of high school, either generally (as classified in excellent student, strong student, weak student or very weak student) or more accurately (as indicated by the exact GPA in the next grade). We also put to the test the widely held notion that it might be best if core courses such as language and mathematics contributed more to the calculation of the GPA compared to secondary courses such as physical education or music. Our findings confirm the predictive properties of the GPA but strongly rebut the notion that a weighted GPA might achieve a better reflection of students’ potential. The study is based on the academic records of every student in Greece that progressed from first to third grade of high school in the 2016-2019 period. This data set contains records of more than 85,000 students, making it one of the most extensive studies ever conducted on the topic of the properties of the GPA.

Opuntia ficus-indica (L.) Mill. belongs to the Cactaceae family and the genus Opuntia; it is a succulent plant that adapts to extreme climatic conditions. The aerial part of the plant consists of the cladodes, morphological changes of branches that appear green, are covered with thorns, and are essential to reduce excessive perspiration of water. The composition of cladodes is very varied, and the main constituents are water, fibers, polysaccharides, proteins, fatty acids, vitamins, sterols, minerals, and polyphenols. Polyphenols are responsible for many beneficial activities for human health, such as antioxidant, anti-inflammatory, antitumor, and nutritional properties. The purpose of this manuscript was to compare the properties of cladodes belonging to the same plant but with different stages of maturity. Relative extracts were tested both in vitro and on a cell line and antioxidant and anti-apoptotic properties were found. The antioxidant activity was tested by the ORAC test, the DPPH test, and the measurement of cellular accumulation of ROS. Anti-apoptotic activity was evaluated by the annexin/PI assay and measurement of caspases 9 and 3 expression. The results obtained have shown that the extracts considered possess antioxidant and anti-apoptotic properties. However, the different stages of maturity of cladodes are essential for the performance of both functions. In addition, important variations have been made in the dissolution of extracts that have brought greater safety in their use. In conclusion, this manuscript provides further information on cladodes of Opuntia ficus-indica, which can be used as adjuvants in many human pathologies.

In this paper, the effects on the rheological properties, particle size distribution, and fluorescence properties of red wine were investigated under microwave irradiation, and the mechanism of the effects of microwave irradiation on the sensory properties of red wine was discussed. The results showed that the effect of microwave on the rheological properties in red wine could be fitted by the Power-law model and Carson model, through the analysis of the rheological constants, yield stress, and viscosity coefficient of wine, it was found that microwave treatment could improve leg phenomenon and thickening effect by the change of rheological properties; the particle size distribution in wine indicated that microwave irradiation did change the particle size distribution through friction effect and oxidative polymerization, resulting in the wine’s visual effect and mouthfeel; the wine quality could be improved by enhancing the fluorescence intensity under different microwave conditions, which meant that microwave technology could speed up the formation of fluorescent substances, such as the polymerization of flavan-3-ols. In conclusion, microwave treatment could modify the sensory characteristics of wine, and further provide the theoretical basis for the application of microwave in winemaking.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Despite the fact that SMA restrainers exhibit a superelastic strain capacity of 7%, this capacity appears inadequate for isolated bridges due to the typically greater than 20cm relative dis-placements between girders during intense seismic events. In order to perform such a stroke, a SMA restrainer of greater than 3 metres in length might be required. In order to reduce the length of restrainers, a novel honeycomb damper constructed from superelastic shape memory alloy (SMA) is proposed. The proposed device, denoted as the superelastic SMA honeycomb damper (SHD), is comprised of steel plates to prevent the SMA plane from collapsing and superelastic SMA honeycomb to provide self-centering capability. By incorporating the large strain capacity of SMA and the geometrically nonlinear deformation of honeycomb structures, SHD has been developed to satisfy the requirements of bridge restrainers with large strokes. It is capable of functioning as a restrainer and energy dissipation device when subjected to dynamic tension and compression loads. The SHD was initially investigated from a theoretical perspective. Following this, a mul-ti-cell SHD specimen was manufactured. The specimen underwent axial tensile and compressive experiments in order to examine the mechanical properties of SHDs. Finally, experimental results were investigated through numerical simulation analyses of the SHDs using a three-dimensional high-fidelity finite element model. Additionally, a method for enhancing SHD was proposed. The findings indicate that SHD is capable of exhibiting superior self-centering capability and sta-ble hysteretic responses when subjected to earthquakes.

Background: We investigated the effect of bioactive glass and zinc oxide nanoparticles on enamel remineralization, as well as their antibacterial effect on cariogenic bacteria. Methods: Fluoride gel (F), bioactive glass microparticles (µB), bioactive glass nanoparticles (nB), zinc oxide nanoparticles (Z), and a mixed suspension of nB and Z (nBZ) were prepared and subjected to the following tests: morphological evaluation by scanning and transmission electron microscopy, measurement of specific surface area, zeta potential measurement, crystal structure analysis by X-ray diffraction, and acid buffering capacity test. Further, we performed a remineralization cycle test of 28 days and a nanoindentation testing was carried out during the immersion period and then the enamel surfaces were examined using scanning electron microscopy. Additionally, the antibacterial effects of the sample suspensions were evaluated by measuring their minimum bactericidal concentrations against various cariogenic bacteria. Results: Our results revealed that nB had a near-circular shape with an amorphous structure, a considerably large specific surface area due to nanoparticulation. Additionally, nB possessed a rapid acid buffering capacity, which was comparable to that of μB. In the remineralization test, faster recovery of mechanical properties was observed on the enamel surface immersed in samples containing bioactive glass nanoparticles (nB and nBZ). After remineralization, demineralized enamel immersed in any of the samples showed a rough and porous surface structure covered with mineralized structures. Furthermore, nBZ exhibited a broad antibacterial spectrum. Conclusions: These results demonstrated that bioactive glass and zinc oxide nanoparticles have superior demineralization-suppressing and remineralization-promoting effects.

Improving the quality of petroleum products and refining processes through the use of artificial intelligence and machine learning techniques is the topic of this article. It shows that expert knowledge and conventional empirical models can't get you where you want to go in a refining process. To effectively capture complex interactions and forecast fuel qualities, machine learning techniques such as principal component analysis (PCA), support vector machines (SVM), artificial neural networks (ANN), and partial least squares (PLS) are suggested. Gasoline and other petroleum products, as well as property prediction, process control, product quality, and operational efficiency in refineries, can all be improved with the help of machine learning applied to spectral or distillation curve data. An exciting new direction in optimizing operations, meeting environmental norms, and precisely estimating gasoline quality is offered by advanced machine learning algorithms.

The composite post insulator composed of a large diameter mandrel and flange pressed by one-time integral pultrusion has high strength and good toughness, widely used in the existing flexible converter valve. For constructing the finite element model of the crimped post insulator, most of the flange surface and the mandrel surface are directly connected, making the simulation model's stiffness deviate from the actual model and the model distortion. Based on this, this study proposes a new finite element simplified model of crimped composite post insulator based on Multi-Point Constraints (MPC), which accurately simulates the crimping area of man-drel and flange in engineering practice. It verifies the model's reliability through static tests and characteristic vibration tests. The results show that the difference between the finite element simulation and test results is within 5 %. The finite element modeling method based on MPC local constraints is very reliable in applying crimped composite post insulators. Based on the proposed model, the influence of flange height and thickness on the mechanical properties of composite post-insulators is further explored. The results show that the influence of flange height on mechanical properties can be ignored when the height of the insulator stiff-ener ( non-press common area ) is constant. Within the allowable thickness range of the flange crimping process, the increase in flange thickness will significantly reduce the maximum bend-ing stress of the insulator and increase its safety margin. It provides a good design idea for the design of crimping composite insulators.

Membrane protein integrase (MPIase), an endogenous glycolipid in Escherichia coli (E. coli) membrane, is essential for membrane protein insertion in E. coli. We have examined Sec-independent membrane protein insertion mechanisms facilitated by MPIase using physicochemical analytical techniques such as solid-state nuclear magnetic resonance, fluorescence measurements, and surface plasmon resonance. In this review, we outline the physicochemical characteristics of membranes that may affect membrane insertion of proteins. Subsequently, we introduce our results verifying the effects of membrane lipids on insertion and estimate the impact of MPIase. Although MPIase is a minor component of E. coli membranes, it regulates insertion by altering the physicochemical properties of the membrane. In addition, MPIase promotes insertion by interacting with substrate proteins. We propose comprehensive mechanisms of membrane insertion of proteins involving MPIase, which provide a physicochemical basis for understanding the roles of glycolipids in protein translocation.

The changes in storage loss, water distribution status, gel characteristics, TBARS, total volatile basic nitrogen, and total plate count of cooked reduced-phosphate silver carp surimi batter during cold storage at 4 °C were investigated. The storage loss, content of free water, pH, hardness, TBARS, total volatile basic nitrogen value and total plate count of all cooked reduced-phosphate silver carp surimi batters significantly increased (P < 0.05) with increasing the cold storage time. Meanwhile, the content of immobilized water, whiteness, springiness, and cohesiveness decreased significantly (P < 0.05). At the same cold storage time, the sample of cooked reduced-phosphate silver carp surimi batter has lower water mobility, darker colour and better texture characteristics, but the values of TBARS, total volatile basic nitrogen and total plate count were not significantly different (P > 0.05). To sum up, the use of potassium bicarbonate instead of sodium tripolyphosphate could produce the cooked reduced-phosphate silver carp surimi batter with better water holding capacity and gel characteristics during cold storage.

Recent advances in nanomaterials have been heavily influenced by low-dimensional nanocarbon allotropes. In particular, carbyne has attracted attention for its potential as a true one-dimensional carbon chain with sp1 hybridization. To maximize the capabilities of this material, we employ a focused data-driven inverse design approach based on the carbon nanomaterials genome concept. This involves using deep learning neural network models to identify key descriptors tied to desired properties, enabling property prediction and reverse engineering of nanocarbons. Our iterative approach entails: (i) gathering growth/property data on nanostructures; (ii) identifying informative numerical/categorical predictors; (iii) developing deep learning models mapping descriptors to properties; (iv) refining models with new insights; (v) determining required descriptors/conditions for target properties via inverse mapping; (vi) validating models by synthesizing predicted nanostructures; and (vii) enhancing models with validation data. This allows uncovering hidden growth-property connections, precisely tuning nanocarbons for desired attributes. We introduce new methodologies including exciting synergistic effects, synchronizing atomic vibrations, active screen plasma, energy-driven transformations, surface acoustic micro/nano-manipulation, doping and directed self-assembly to expose relationships and integrate insights into the inverse design flow. This research promises to accelerate discovery of next-generation low-dimensional nanocarbons with exceptional properties and applications.

In the following article I take into consideration the role of knowledge workers in the Italian regions. The analysed data refers to the ISTAT-BES database. The metric analysis consists of an in-depth analysis of the trends of the regions and macro-regions, followed by clustering with the k-Means algorithm, the application of machine learning algorithms for prediction, and the presentation of an econometric model with panel methods date. The results are also critically discussed in light of the North-South divide and the economic policy implications.

The effects of different pulse frequencies on the microstructure grain size and solid solubility of Al-9Si alloy were systematically investigated using OM, SEM, and EDS. The effects on the mechanical properties of the alloy were analyzed using micro-Vickers hardness tester and multifunctional friction tester. During the solidification process, the Al-9Si alloy is exposed to high-frequency electric current pulses with a current density of 300A/cm2 and frequencies of 0Hz, 500Hz, 1 000Hz, and 2 000Hz. The experimental results show that as the high-frequency pulse frequency increases, the Lorentz force also increases. The intense electromagnetic stirring leads to grain refinement. However, as the pulse frequency continues to increase, the combined effect of Joule heating and Lorentz force results in an enlargement of the melt zone and an increase in grain size. At a pulse frequency of 1 000Hz, the eutectic structure size of the Al-9Si alloy is optimal, with the average size reduced to 13.87μm and a dense distribution, effectively eliminating primary Si. The EDS results revealed that the high-frequency pulse led to a more uniform distribution of Si elements within the matrix, and the solid solubility of Si in the α-Al matrix increased to a maximum value of 1.99%, representing a 39.2% increase. At a pulse frequency of 1 000Hz, the sample demonstrates the most favorable mechanical properties, with the friction coefficient reaching a minimum value of 0.302, representing a 37.7% decrease in the average friction coefficient. The results demonstrate that high-frequency pulsing is an effective method for enhancing the mechanical properties of Al-9Si alloy.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

In this work, Al-Mo-B(CN) thin coatings were deposited by magnetron sputtering using composite metal-ceramic Al-Mo-B4C target. A metal-ceramic composite target for magnetron sputtering was fabricated by a robotic complex for detonation spraying of coatings equipped with a multi-chamber detonation accelerator. The powder composition (30Mo-30Al-40B4C) was sprayed onto the copper plate base of the composite target-cathode. The obtained cathode target with Al-Mo-B4C coating (thickness 280-300 μm) was used to deposit the Al-Mo-B(CN) coating (DC mode) on flat specimens of AISI 316 steels and silicon using equipment for magnetron sputtering UNICOAT 200. The Al-Mo-B4C coating has a lamella-type structure with inclusions of boron car-bide particles the elemental composition is evenly distributed in the material. The structure and morphology of coatings were studied using methods of optical, scanning electron microscopy (SEM), atomic force microscopy (AFM), X-ray analysis (XRD), and X-ray photoelectron spectros-copy (XPS). Mechanical and tribological properties of the Al-Mo-B(CN) thin coatings were determined using methods of nanoindentation, scratch testing, and tribological testing under fluid-free friction regime at room temperature. The Al-Mo-B(CN) coating (thickness ~ 1 μm) exhibited a dense uniform fine-grained structure with no columnar elements and were well-adherent to the substrates after deposition. Al-Mo-B(CN) coating has a amorphous structure. XPS analysis confirmed the formation of the MoB2 and AlN phase with an admixture of oxygen in the form of aluminum oxide, molybdenum oxide and boron oxide. Al-Mo-B(CN) coating possess hardness of 13 GPa, elasticity modulus of 114 GPa, elastic recovery of 45%, and friction coefficient of 0.8 against steel 100 Cr6 ball. The failure mode occurring in the tested coatings was fatigue and abrasive. The adhesion strength of Al-Mo-B(CN) coating amounted to about 11 N, and the failure mode was cohesive associated with plastic deformation and formation of fatigue cracks in the coating material.

This paper proposes a lightweight joint with bamboo culm cross connection, which is constructed by screwing one side of the screw into the other side of the wooden plug, its simple construction makes it easy to manufacture and cost-effective. This form connects adjacent bamboo culms to form corner joints, and bolt connects adjacent bamboo culm frames to form edge joints, to explore the mechanical properties of the combination joints formed by corner joints and edge joints, by combining experiments and numerical simulations, the method discovered and explained the relationship and mechanism between the number and position of bolts and the stiffness of edge joints. A calculation model for frame-unit bamboo culm members considering semi-stiffness of joints is proposed, and the conversion equations between linear stiffness of corner and edge joint and their rotational stiffnesses are derived. By establishing the series and parallel relationship between the corner and edge joints in the assembled members, a generalized relational equation between the total stiffness of the assembled joint and the stiffness of the corner and edge joints is derived. A numerical simulation method for frame-unit bamboo culm members with semi-rigid joints is proposed, which can obtain the stiffness calculation formula of edge joints and the average rotational stiffness value of semi-rigid corner joints. A finite element analysis method based on semi-rigid joints is proposed for frame-unit bamboo culm members, and the internal force sketches and calculation methods for bamboo culms and joints are presented, which can be used for the internal force analysis and design of frame-unit bamboo culm lattice structures.

In the following article I analyze the determinants of regular internet users in the Italian regions. The data is analyzed both in terms of static analysis and also through the application of the k-Means algorithm optimized with the Elbow method. Subsequently, an econometric model is presented for estimating regular internet users in the Italian regions based on variables that reflect the state of technological innovation and digital culture. The results are analyzed and discussed in light of the implications that digitalisation has for triggering economic growth.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

We introduce a new generalized inverse (i.e., generalized EP element) which is a natural generalization of EP and *-DMP elements in a Banach *-algebra. We present polar-like characterizations of generalized EP elements. The necessary and sufficient conditions under which the sum of two generalized EP elements is a generalized EP element are investigated. Finally, the generalized core-EP orders for generalized EP elements are characterized.

In order to further reduce the emissivity of the hydrophobic low infrared emissivity composite coating and improve the mechanical properties of the coating, the dispersant, adhesion enhancer, and defoamer were used to improve the dispersion state of the fillers, the interface structure, and the surface state of the hydrogen silicone oil modified polyurethane/Al composite coating. The effects of dispersant, adhesion enhancer, and defoamer on the micro-structure, emissivity, glossiness, hydrophobic property, and mechanical properties of the coating were systematically studied. The results show that the polycarboxylate anionic dispersant can obviously improve the dispersion state of flake Al powder and nano-SiO2 in the coating, so that the infrared emissivity of the coating can be reduced, and the coating can have higher hydrophobic and mechanical properties. The bonding strength between the resin matrix and the metal substrate of the coating can be significantly improved by the adhesion enhancer through the bridging action, so that the adhesion strength and impact strength of the coating can be significantly improved. The defoamer can significantly reduce the pores in the coating, so that the surface state of the coating can be significantly improved, and the mechanical properties of the coating can be significantly improved. The coating has the best emissivity (0.527), glossiness (4.3), adhesion strength (grade 1), impact strength (40 kg.cm), and hydrophobic property (water contact angle (WCA) is 140o) when the amount of dispersant, adhesion enhancer, and defoamer is 5 wt%, 4 wt%, and 1 wt%, respectively.

This paper presents the results of the study of carbon films deposited on substrates of quartz, mica and silicon by the method of electron paramagnetic resonance (EPR). This study has identified the dependences of the intensities of the EPR signal, the g- factor, and the line width on the temperature of carbon films on various substrates with perpendicular and parallel arrangement of the sample plane relative to the orientation of the magnetic field are presented. The results of this study show that the dependence of the line width on temperature measurements does not change under both conditions for recording the EPR spectra. The research has also shown that with increasing temperature, the normalized intensity of the EPR signal line increases when carbon is deposited on various substrates (quartz, mica, and silicon) by the method of plasma decomposition of a mixture of CH4 and H2.

in the following article I analyze the trend of cultural and creative employment in the Italian regions between 2004 and 2022 through the use of ISTAT-BES data. After presenting a static analysis, I also present the results of the clustering analysis aimed at identifying groupings between Italian regions. Subsequently, an econometric model is proposed for estimating the value of cultural and creative employment in the Italian regions. Finally, I compare various machine learning models for predicting the value of cultural and creative employment. The results are critically discussed through an economic policy analysis.

In this paper, we investigate some elementary properties of two kinds modified Szasz type basis functions, depending on non-negative parameters. We study some shape preserving properties of these operators concerning monotonicity, convexity, starlikeness, semi-additivity and smoothness.

Elastic yarns are the key component of high-performance compression garments. However, it remains a challenge to fabricate anti-fatigue yarns with high mechanical force and long elongation for generating compression garments with prolonged wear. In this paper, we report the development of anti-fatigue double-wrapped yarns with excellent mechanical properties by wrapping high-denier Spandex with nylon filaments in opposite twists. In particular, 560D high-denier Spandex as the core was untwisted which can maximumly reduce the interaction between the core and wrapping filaments, enabling high elongation of the double-wrapped yarns. In addition, we chose 70D nylon filaments with a tensile force of 387.40 ± 8.82 cN as the wrapping materials to provide sufficient force for double-wrapped yarns. Notably, opposite twists were induced for the inner and outer wrapping filaments to achieve a balanced stable yarn structure. By systematically optimizing manufacturing parameters including inner wrapping density, outer wrapping density, taking-up ratio, and drafting ratio, we obtained double-wrapped yarn with excellent tensile force (952.00 ± 24.03 cN) and elongation (357.28% ± 9.10%). Notably, the stress decay rate of optimized yarns was only 12.0% ± 2.2%. In addition, the optimized yarn was used as the weft-lining yarn for generating weft-lined fabrics, the elastic recovery rate of the obtained fabric was only 2.6% after cyclic stretching, much lower than the control fabric. Our design of anti-fatigue double-wrapped yarns could be widely used for fabricating high-performance compression garments.

Entangled metallic wire material (EMWM) can be utilized as a novel elastic element in vibration isolation devices for mechanical actuators. This paper presents a vibration experiment aimed at investigating the degradation behavior of mechanical performance in EMWM under cyclic compressive environment. An electric vibration testing system, coupled with an isolation structure, is employed to apply compressive loads to the EMWM specimens. Through visual observations and quasi-static compression tests, the variations in geometric morphology and mechanical properties are studied, considering different relative densities and stress amplitudes. The results incidate a significant reduction in the compressed dimension of the specimens as the number of cycles increases, without any wire fractures or wear. Moreover, the mechanical properties exhibit an increasing secant modulus and a decreasing loss factor. These variations ultimately lead to a gradual deviation of the vibration characteristics of the isolation structure from its design state. To predict the mechanical property degradation of EMWM, prediction models are proposed, incorporating dimension, modulus and damping by fitting the obtained results. This research provides valuable experimental data and presents an effective method to determine the operational lifetime of vibration isolators utilizing EMWM.

The dolomite dust-emulsified asphalt composite with excellent mechanical properties was successfully prepared using alkali activation. The effects of different alkali concentrations and emulsified asphalt contents on the mechanical properties of the materials were studied. The mechanical properties and microstructure of the composites were analyzed using compressive strength tests, bending strength tests, and SEM characterization. The experimental results show that the specimens have excellent mechanical properties: the 7-day compressive strength can reach 76.67 MPa, and the bending strength is about twice that of silicate-based geopolymer-emulsified asphalt composite. With an increase in emulsified asphalt content, the compressive strength of the samples decreases, while the bending strength increases first and then decreases. When the emulsified asphalt content is 1%, the bending strength of the sample is up to 28.81 MPa, which is 25% higher than that of the sample without emulsified asphalt. This indicates that an appropriate emulsified asphalt content can play a toughening role in the system, providing a new idea for designing high-toughness alkali-activated materials.

The following article analyzes Italian companies with more than 10 employees that use online sales tools. The data used were acquired from the ISTAT-BES database. The article first presents a static analysis of the data aimed at framing the phenomenon in the context of Italian regional disparities. Subsequently, a clustering with k-Means algorithm is proposed by comparing the Silhouette coefficient and the Elbow method. The investigation of the innovative and technological determinants of the observed variable is carried out through the application of a panel econometric model. Finally, different machine learning algorithms for prediction are compared. The results are critically discussed with economic policy suggestions.

The Polyurethane (PU) mixture is a high−performance engineering material with different dynamic properties compared to a hot−mixed asphalt mixture (HMA). This paper analyzed whether the Kramers−Kronig (K−K) relation and thermo−rheological simple properties were applicable to the PU mixture. Based on the result discussion, the PU mixture exhibited thermo−rheological simple properties within the test conditions. The time−temperature superposition principle (TTSP) was applicable for the PU mixture to construct the dynamic modulus master curve using the standard logistic Sigmoidal (SLS) model, the generalized logistic sigmoidal (GLS) model, and the Havriliak−Negami (HN) model. The Hilbert integral transformed SLS and GLS models for the phase angle can accurately fit the measured phase angle data with newly fitted shift factors and predict the phase angle within the viscoelastic range. The Core−Core and black space diagrams both displayed single continuous smooth curves, which can be utilized to characterize the viscoelastic property of the PU mixture. The K−K relation is applicable for the PU mixture to obtain the phase angle master curve model, storage modulus, and loss modulus from the complex modulus test results. The phase angle of the PU mixture cannot be derived from the dynamic modulus data and currently needs to be derived from the laboratory measurement.