Natural gas is an important energy source among various fossil fuels. However, natural gas typically contains a significant amount of water vapor, which can pose challenges in its usage. Therefore, the process of removing water vapor from natural gas, known as gas dehydration, is crucial in the gas industry. The presence of water vapor in the gas supply can lead to the formation of hydrates, which can cause issues such as blockages in pipelines. To tackle this problem effectively, gas dehydration makes use of Tri ethylene glycol (TEG) as a drying agent. TEG works by selectively absorbing water vapor from the natural gas flow, thereby significantly reducing its moisture content.In the gas dehydration process, wet gas is treated by using lean glycol in an absorber, where the water vapor is removed. The resulting rich glycol is then recovered and recycled for further use. In this study, we explore the possibility of replacing nitrogen with dry natural gas in the re-generator of the glycol dehydration system. The aim is to evaluate the feasibility and effectiveness of this alternative approach. To assess the performance of both techniques, we employed HYSYS modeling and simulation. Through this analysis, we compared the capital and utility expenses associated with each method while ensuring that the glycol purity requirements remained unchanged. By examining the results obtained from the simulations, we can gain insights into the economic viability and efficiency of utilizing dry natural gas in the re-generator stage of the glycol dehydration process.In addition to the primary purpose of removing water vapor, the wet gas obtained from the stripping mechanisms in the glycol dehydration process can serve additional functions. It can be utilized to power steam pumps and compressors, thereby maximizing energy efficiency within the system. Alternatively, the wet gas can be recycled back into the process for further treatment. To develop a comprehensive understanding of the entire mechanism, we constructed a model based on the actual flow diagram. This model takes into account the various components and processes involved in the glycol dehydration system, including the stripping mechanisms and their connection to other equipment. By analyzing the data and outcomes generated by this model, we can derive valuable insights. These findings can be utilized to optimize the heat and material balance within the plant, ensuring efficient operation and potentially leading to the design of an improved system in terms of energy consumption and overall performance

Among other fossil fuels, natural gas is a major energy source. It is generally created saturated with water vapor. Dehydration of natural gas is vital in the gas business to remove water vapor from the gas supply, which may cause hydrate development in pipes. Gas dehydration employs Tri ethylene glycol (TEG) to remove water vapor from natural gas flow. The wet gas is dehydrated with lean glycol in an absorber, and the rich glycol is recovered and reused. This work investigates the use of dry natural gas instead of nitrogen in the glycol dehydration re-generator, and compares the results using HYSYS modeling and simulation. The two techniques were compared for capital and utility expenses, while maintaining the identical glycol purity criteria. The wet gas from the stripping mechanisms may also be utilized to run steam pumps and compressors or recycled. The model is based on the real mechanism flow diagram. Finally, the findings of this model might be used to design a new heat and material balance for the plant.

Tryptanthrin has not been widely applied in clinical practice due to its poor solubility and low bioavailability in spite of possessing several biological and pharmacological activities. Here, to improve the solubility of tryptanthrin, two types of novel tryptanthrin-loaded micelles were prepared. One was tryptanthrin physically encapsulated by distearoyl phosphatidylethanolamine polyethylene glycol (DSPE-PEG) and the other was pegylated tryptanthrin synthesized by acid-sensitive hydrazone bond and further prepared as micelles. Molecular imprinting technology was used to separate pegylated tryptanthrin and free mPEG-COOH in the preparation of PEGylated tryptanthrin micelles with considerably high separation efficiency. The solubility of tryptanthrin-loaded DSPE-PEG micelles (TDMs) and PEGylated tryptanthrin micelles (PTMs) was increased by 300 and 1493 fold compared with that of tryptanthrin, respectively. The PTMs increased the solubility of tryptanthrin more effectively and 95% of tryptanthrin was released from PTMs at pH 5.5 in 12 h. The cytotoxicity of PTMs decreased under physiological conditions compared with that of tryptanthrin, whereas at pH 5.5, the PTMs showed comparable cytotoxicity with that of tryptanthrin, indicating successful drug release from the carrier in response to tumor cell pH. Overall, we elucidated an efficient method to improve water solubility of tryptanthrin and indicated pegylated tryptanthrin is a promising prodrug.

This study aimed to evaluate if the change of vehicle for CTZ (chloramphenicol, tetracycline, zinc oxide, and eugenol) paste improves the inhibition of Enterococcus faecalis in vitro. The vehicles evaluated alone and mixed with CTZ were eugenol, propylene glycol (PG), chitosan, su-per-oxidized solution (SOS), grapefruit-seed extract (GSE), and as a negative control, 0.9% saline solution. A clinical isolated of E. faecalis was morphological and biochemical characterized, in-cluding antimicrobial susceptibility was tested using 20 antimicrobial agents. Once character-ized, the clinical isolated was cultivated to performed Kirby–Bauer disc diffusion method with paper discs embedded with the different vehicles mixed or used alone, incubating at 37 ºC for 24 h. Data were analyzed by One-way ANOVA and the means were compared using Tukey test with a significance level of p<0.05. For vehicles used alone, GSE presented the greatest inhibition showing a statistically significant difference with the rest of the vehicles. When vehicles were mixed with the CTZ paste, PG showed a greater inhibition with a statistically significant differ-ence from the rest of the vehicles. In conclusion, the vehicle used to mix the CTZ paste plays an im-portant role in the inhibition of E. faecalis in vitro, therefore we consider that this can be an im-portant factor to achieve success in the use of this technique.

Grafting polyethylene glycol (PEG) on polymers surface is widely used to improve biocompatibility by reducing protein and cell adhesion. Although PEG is considered to be bioinert, its incorporation to biomaterials has shown to improve cell viability depending on the amount and molecular weight (MW) used. This phenomenon was studied here by grafting PEG of three MW onto polyurethane (PU) substrata at three molar concentrations to assess their effect on PU surface properties and on the viability of osteoblasts and fibroblasts. PEG formed a covering on the substrata which increased the hydrophilicity and surface energy of PUs. Among the results it was observed that osteoblast viability increased for all MW and grafting densities of PEG employed compared with unmodified PU. However, fibroblast viability only increased at certain combinations of MW and grafting densities of PEG, suggesting an optimal level of these parameters. PEG grafting also promoted a more spread cell morphology than that exhibited by unmodified PU; nevertheless, cells became apoptotic-like as PEG MW and grafting density were increased. These effects on cells could be due to PEG affecting culture medium pH, which became more alkaline at higher MW and concentrations of PEG. Results support the hypothesis that surface energy of PU substrates can be tuned by controlling the MW and grafting density of PEG, but these parameters should be optimized to promote cell viability without inducing apoptotic-like behavior.

Our aim was to evaluate efficacy and safety of 30mL CaO alone or plus Asc in bowel preparation before colonoscopy. Two hundred and forty six patients were allocated randomly to ingest 2L PEG with 30mL CaO, 1L PEG with 30mL CaO plus 5g Asc, or 3L PEG. We used Boston Bowel Preparation Scale (BBPS) to evaluate bowel preparation efficacy. We also determined other outcomes such as procedure time, polyp or adenoma detection rate and adverse events (AEs). Of 282 patients recruited, 36 were excluded. Groups were matched for baseline characteristics except weight (P = 0.020) and body mass index (BMI) (P = 0.003). Patient’s satisfaction were higher in 2L PEG-CaO (P = 0.016) and 1L PEG-CaO-Asc groups (P = 0·017). Patients’ compliance was 67.5%, 71.4% and 80.5% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.014). Adequate bowel preparation rate was 75%, 78.57% and 53.66% in 3L PEG, 2L PEG-CaO and 1L PEG-CaO-Asc groups (P = 0.021). There were no differences in terms of remaining outcomes. Despite an increase in patients’ satisfaction and compliance, 1L PEG-CaO-Asc significantly decreased adequate bowel preparation rate. However, 2L PEG-CaO improved the patients' satisfaction and compliance and increased adequate bowel preparation rate.

Managing severe bleeding, particularly in soft tissues and visceral injuries, remains a significant challenge in trauma and surgical care. Traditional hemostatic methods often fall short in wet and dynamic environments. This study addresses the critical issue of severe bleeding in soft tissues, proposing an innovative solution using a Polyethylene Glycol (PEG)-based hydrogel combined with zinc oxide (ZnO). The developed hydrogel forms a dual-network structure through amide bonds and metal ion chelation, resulting in enhanced mechanical properties and adhesion strength. The hydrogel, exhibiting excellent biocompatibility, is designed to release zinc ions, promoting coagulation and accelerating hemostasis. Comprehensive characterization, including gelation time, rheological properties, microstructure analysis, and swelling behavior, demon-strates the superior performance of the PEG/ZnO hydrogel compared to traditional PEG hydro-gels. Mechanical tests confirm increased compression strength and adhesive properties, crucial for withstanding tissue dynamics. In vitro assessments reveal excellent biocompatibility and en-hanced procoagulant ability attributed to ZnO. Moreover, in vivo experiments using rat liver and tail bleeding models demonstrate the remarkable hemostatic performance of the PEG/ZnO hy-drogel, showcasing its potential for acute bleeding treatment in both visceral and peripheral sce-narios.

Due to their distinct physical, chemical, and biological characteristics, biopolymers, in particular Poly Ethylene Glycol (PEG) and Cellulose, are frequently used in biomedical medicine as drug or vaccine delivery systems. In this study, we have done a systematic review and a meta-analysis to compare current developments in many PEG and cellulose-based hydrogels, including double network hydrogels, injectable hydrogels, sliding hydrogels, conductive hydrogels, responsive hydrogels, and nanocomposite hydrogels. The pharmacokinetic properties, including physicochemical properties, biocompatibility, biodegradability, temperature, and pH, have been studied as these critical factors are to be considered for deciding the suitability of the drug for delivery. Moreover, the study has evaluated the controlled-release parameters such as half-life, circulation time, maximum release percentage of loaded drug released, burst release, maximum release, and drug-release kinetics. Finally, the efficacy and immune response of hydrogel was studied for future choice, including the cellulose hydrogel system in COVID-related long-term vaccine delivery. The finding revealed that cellulose-based hydrogel is effective for vaccine delivery.

L-glutamate is one the most important excitatory neurotransmitter at central nervous system level and it is implicated in several pathologies. So, it is very important to monitor its variations, in real time in animal models’ brain. Amperometric biosensors have been used because of their very high temporal and spatial resolution, and because suitable for a short to mid-term implantation. The present study aimed to develop and characterize a new glutamate biosensor design that exploits the selectivity of Glutamate Oxidase (GluOx) for l-glutamate, and the capability of a small molecule as propylene glycol (PG) to influence and extend the stability and the activity of enzyme. Different designs were evaluated by modifying the main components in their concentrations to find the most suitable design. Moreover, enzyme concentrations from 100 U/ml up to 200 U/ml were verified and different PG concentrations (1%, 0.1% and 0.05%) were tested. The most suitable selected design was Pt_c/PPD/PEI(1%)₂/GlutOx₅/PG(0.1%) and it was compared to the same already described design loading PEDGE, instead of PG, in terms of over-time performances. PG has proved to be capable of determining an over-time stability of the glutamate biosensor in particular in terms of linear region slope (LRS) up to 21 days.

Separation of polyethylene glycols (PEGs) into single homologs by reversed-phase chromatography is investigated experimentally and theoretically. The used core-shell column is shown to achieve baseline separation of PEG homologs up to molar weights of at least 5000 g/mol. A detailed study is performed elucidating the role of the operating conditions temperature, eluent composition, and degree of polymerization of the polymer. Applying Martin's rule yields a simple model for retention times that holds for a wide range of conditions. In combination with relations for column efficiency, the role of the operating conditions is discussed and separations are predicted for analytical-scale chromatography. Finally, the approach is included in an efficient process model based on discrete convolution, which is demonstrated to predict with high accuracy also advanced operating modes with arbitrary injection profiles.

In order to obtain stable super-hydrophobicity, suitable hydrophobic treatment agent should be selected according to different materials. In this paper, cotton and poly (-ethylene terephthalate) (PET) fabric was respectively coated by dodecyl methacrylate (LMA) via argon combined capacitively coupled plasma (CCP), and the surface hydrophobicity and durability of treated cotton and polyester fabrics were also discussed. An interesting phenomenon was happened that LMA coated cotton fabric (Cotton-g-LMA) had better water repellency and mechanical durability than LMA coated PET fabric (PET-g-LMA), and LMA coated hydroxyl grafted PET fabrics (PET fabrics were successively coated with polyethylene glycol (PEG) and LMA, PET-g-PEG&amp;LMA) had similar performance to those of cotton fabrics. The water contact angle (WCA) of Cotton-g-LMA, PET-g-LMA and PET-g-PEG&amp;LMA was 156 °, 153 ° and 155 °, respectively, and after 45 washing cycles or 1000 rubbing cycles, the corresponding WCA was decreased to 145 °, 88 °, 134 °and 146 °, 127 °, 143 °, respectively. Also, thermoplastic polyurethane (TPU) and polyamides-6 (PA6) fabrics were all exhibited the same properties to PET fabric. Therefore, the grafting of hydroxyl can improve the hydrophobic effect of LMA coating and the binding property between LMA and fabrics effectively without changing the wearing comfort..

Plastics have become an important environmental concern due to their durability and resistance to degradation. Out of all plastic materials, polyesters such as polyethylene terephthalate (PET) are amenable to biological degradation due to the action of microbial polyester hydrolases. The hydrolysis products obtained from PET can thereby be used for the synthesis of novel PET as well as becoming a potential carbon source for microorganisms. In addition, microorganisms and biomass can be used for the synthesis of the constituent monomers of PET from renewable sources. The combination of both biodegradation and biosynthesis would enable a completely circular bio-PET economy beyond the conventional recycling processes. Circular strategies like this could contribute to significantly decrease the environmental impact of our dependence on this polymer. Here we review the efforts made towards turning PET into a viable feedstock for microbial transformations. We highlight current bottlenecks in the degradation of the polymer and the metabolism of the monomers and we showcase fully biological or semisynthetic processes leading to the synthesis of PET from sustainable substrates.

Although cofactor regeneration is an established system in biocatalysis, work remains in developing new and alternative cofactor regeneration systems with greater efficiency, ease of use, and higher atom economy. In addition, cofactor regeneration system only works if the cofactor regeneration reaction operates at similar kinetics compared to the biotransformation reaction. This meant that only specific cofactor regeneration system is capable of coupling with particular biotransformation reaction. This then leaves open the field for the development of a plethora of alternative cofactor regeneration systems each capable of coupling with different biotransformation reaction of different kinetics. This short write-up examines the possibility of tapping on the NADH regenerated from a two-step ethylene glycol utilization pathway. Current knowledge suggests that this angle has not been explored; thereby, opening up possibilities for future experimental investigations into the feasibility of coupling ethylene glycol utilization pathway with biotransformation reaction as a coupled cofactor regeneration system.

We reported previously that poly (3-hydroxybutyrate) (PHB) oligomer is an effective antimicrobial agent against gram-positive bacteria, gram-negative bacteria, fungi and multi-drug resistant bacteria. In this work, it was further found that polyethylene glycol (PEG) can promote the antimicrobial effect of PHB oligomer synergistically. Three hypothetic mechanisms were proposed, that is, generation of new antimicrobial components, degradation of PHB macromolecules and dissolution/dispersion of PHB oligomer by PEG. With a series of systematic experiments and characterizations of HPLC-MS, it was deducted that dissolution/dispersion of PHB oligomer dominated the synergistic antimicrobial effect between PHB oligomer and PEG. This work demonstrates a way for promoting antimicrobial effect of PHB oligomer and other antimicrobial agents through improving hydrophilicity.

Plant cells are omnipotent and breeding of new varieties can be achieved by protoplast fusion. Such fusions can be achieved by treatment with poly(ethylene glycol) or by applying an electric field. Microfluidic devices allow for controlled conditions and targeted manipulation of small batches of cells down to single cell analysis. To provide controlled conditions for protoplast fusions and achieve high reproducibility, we developed and characterized a microfluidic device to reliably trap few of Arabidopsis thaliana protoplasts and induced a cell fusion by controlled addition of poly(ethylene glycol) (PEG, with a molecular weight of 6000). Experiments were conducted to determine the survival rate of isolated protoplasts in our microfluidic system. Afterwards, PEG induced fusion was studied. Our results indicate that the following fusion parameters had significant impact on the fusion efficiency and duration: PEG concentration, osmolarity of solution, and flow velocity. PEG concentration below 10% led to only partial fusion. Osmolarity of the PEG fusion solution was found to strongly impact the fusion process; complete fusion of two source cells sufficiently took part in slightly hyper osmotic solutions, whereas iso-osmotic solutions led to only partial fusion at 20% PEG concentration. We observed accelerated fusion for higher fluid velocities. Up to this study, it was common sense that fusion is one directional, i.e. once two cells were fused into one cell they stay fused. Here, we present for the first time reversible fusion of protoplasts. Our microfluidic device paves the way to a deeper understanding on the kinetics and processes of cell fusion.

Polyethylene glycol (PEG) is an inert, water soluble polymer, used for decades in pharmaceuticals. Although PEG is considered safe, concerns persist about the potential adverse effects of long-term exposure to PEG-containing therapies, specifically in children, following the introduction of PEGylated recombinant factor products used for the treatment of hemophilia. Given the absence of long-term surveillance data, and to evaluate the potential risk, we estimated PEG exposure in the pediatric population receiving US Food and Drug Administration-approved parenteral therapies with pediatric indications. We used a range of pediatric weights and doses based on prescribing information (PI) or treatment guidelines. PIs and reporting websites were searched for information about adverse events (AEs). For a child weighing 50 kg on the highest prophylactic dose of a FVIII product, the range of total PEG exposure was 40–21,840 mg/year; for FIX products, the range was 13–1342 mg/year; and for other products, the range was 383–26,743 mg/year, primarily as a derivative excipient. No AE patterns attributable to PEG were found for any of these products, including potential renal, neurological, or hepatic AEs. Our analyses suggest the pediatric population has had substantial exposure to PEG for several decades, with no evidence of adverse consequences.

Background: During esophagogastroduodenoscopy performed with colonoscopy, gastric and duodenal erythema, erosions, and ulcerations are often observed. This investigation was designed to review the prevalence of gastroduodenal lesions in patients who underwent wireless capsule endoscopy using standard bowel cleansing preparations, but no endoscopy or sedation. Methods: A retrospective analysis was conducted on patients referred for capsule endoscopy. Records and capsule reports were reviewed for patient demographics, preparation prescribed, procedural indications, and gastroduodenal findings. Preparations studied included polyethylene glycol lavage (PEG), PEG plus bisacodyl (PEG+bis), bisacodyl (bis), oral sulfate solution (OSS) and no prep. Results: Among the 1236 records, 498 (40.3%) were men and 738 (59.7%) were women. The mean age was 57 years +/- 17.8 years SD. The percentage of patients with lesions after any bowel preparation was 52.7% for gastric lesions and 23.6% for duodenal lesions. The percentage of patients with gastroduodenal lesions was 58.3% with prep, compared to 38.2% without prep. These findings were statistically significant with RR 1.53 [1.19-1.94] (p-value=0.00004). This difference was more pronounced in the OSS group RR 1.65 [1.29-2.1] and bisacodyl groups RR 1.64 [1.25-2.15] compared to the PEG group RR 0.95 [0.7-1.3]. Conclusion: This study showed that patients undergoing wireless capsule endoscopy who received bowel preparations had a significant increase in gastric and duodenal lesions. Of the preparations studied, OSS was associated with the greater number of gastroduodenal lesions, while PEG was the least associated with lesions with an occurrence similar to the non-prep group. The clinical significance of these lesions remains undetermined.

Extracellular vesicles (EVs) are membranous vesicles secreted by both prokaryotic and eukaryotic cells and play a vital role in intercellular communication. EVs are classified into several subtypes based on their origin, physical characteristics, and biomolecular makeup. Exosomes, a subtype of EVs, are released by the fusion of multivesicular bodies (MVB) with the plasma membrane of the cell. Several methods have been described in literature to isolate exosomes from biofluids including blood, urine, milk, and cell culture media among others. While differential ultracentrifugation (dUC), has been widely used to isolate exosomes, other techniques including ultrafiltration, precipitating agents such as poly-ethylene glycol (PEG), immunoaffinity capture, microfluidics and size exclusion chromatography (SEC) have emerged as credible alternatives with pros and cons associated with each. In this review, we provide a summary of commonly used exosomal isolation techniques with a focus on SEC as an ideal methodology. We evaluate the efficacy of SEC to isolate exosomes from an array of biological fluids, with a particular focus on its application to adipose tissue-derived exosomes. We argue that exosomes isolated via SEC are relatively pure and functional, and that this methodology is reproducible, scalable, inexpensive, and does not require specialized equipment or user expertise.

Drought is one of the major stress factors affecting growth and development of plants. In this context, drought-related losses of crop plant productivity impede sustainable agriculture all over the world. In general, plants responses to water deficit by multiple physiological and metabolic adaptations at the molecular, cellular and organism levels. To understand the underlying mechanisms of drought tolerance, adequate stress models and arrays of reliable stress markers are required. Therefore, in this review we comprehensively address currently available models of drought stress, based on culturing plants in soil, hydroponic or agar culture. These experimental setups give access to different aspects of plant response to drought, like decrease of tissue water potential, reduction of stomata conductance and photosynthesis efficiency, accumulation of low-molecular weight solutes (metabolic adjustment) and drought protective proteins. Till now, this pattern of markers was successfully extended to the methods of enzyme chemistry, molecular biology and omics techniques. Thus, conventional tests can be efficiently complemented by determination of phytohormone and reactive oxygen species (ROS) contents, activities of antioxidant enzymes, as well as comprehensive profiling of transcriptome, proteome and metabolome.

Dynamic tribochemical processes for dicationic ionic liquid containing a germinal imidazolium cation head groups bridged by a poly(ethylene glycol) and bis(trifluoromethylsulfonyl)imide anion were studied using time-resolved Mechanically Stimulated Gas Emission Mass-Spectrometry (MSGE-MS). In comparison with similar monocationic imidazolium ionic liquids with short alkylic or long polyether side chains the dicationic ionic liquid had lower coefficient of friction on Ti6Al4V alloy and smoother behaviour. The analysis of volatile decomposition products suggested multiple tribochemical reactions in which both anionic and cationic moieties are involved. Tribochemical degradation of cations was mainly through detachment of the side and bridging chains from the imidazolium head groups. Absence of volatile products containing nitrogen implies that imidazole group remained unchanged. Hydrogen and water desorption were attributed to the reactions of hydrogen fluoride being a product of anion degradation with titanium and titanium oxide.

Infection with Severe Acute Respiratory Syndrome coronavirus 2 (SARS-CoV-2) causes Coronavirus Disease 2019 (COVID-19), which has reached pandemic proportions. A number of effective vaccines have been produced, including mRNA vaccines and viral vector vaccines, which are now being implemented on a large scale in order to control the pandemic. The mRNA vaccines are composed of the Spike S1 protein encoding mRNA, incorporated in a lipid nanoparticle, stabilized by polyethylene glycol (PEG). mRNA vaccines are novel in many respects, including cellular uptake, the intracellular routing, processing, and secretion of the viral protein. Viral vector vaccines have incorporated DNA sequences encoding the SARS-CoV-2 Spike S1 protein into (attenuated) adenoviruses. The antigen presentation routes in MHC class I and class II, in relation to induction of virus neutralizing antibodies and cytotoxic T-lymphocytes will be reviewed. In rare cases, mRNA vaccines induce unwanted immune mediated side effects. mRNA based vaccines may lead to an anaphylactic reaction. This reaction may be triggered by PEG. The intracellular routing of PEG, and potential presentation in the context of CD1 will be discussed. Adenovirus vector based vaccines have been associated with thrombocytopenic thrombosis events. The anti-platelet factor 4 antibodies found in these patients could be generated due to conformational changes of relevant epitopes presented to the immune system.

Notwithstanding the advances achieved in the last decades in the field of synthetic bone substitutes, the development of biodegradable 3D scaffolds with ideal mechanical and biological properties remains an unattained challenge. In this work, a novel approach is explored to produce synthetic bone grafts mimicking the complex bone structure using additive manufacturing. For the first time, scaffolds were produced, using an extrusion technique, composed of a thermoplastic polymer, polycaprolactone (PCL), hydroxyapatite nanoparticles (HANp), and polyethylene glycol diacrylate (PEGDA). These scaffolds were further compared with two groups of scaffolds: one composed of PCL and another of PCL and HANp. After production, optimisation and characterisation of these scaffolds, an in vitro evaluation was performed using human dental pulp stem/stromal cells (hDPSCs). Through the findings it was possible to conclude that PEGDA scaffolds were successfully produced presenting networks of interconnected channels, presenting hydrophilic properties (15.15 4.06°), adequate mechanical performance (10.41MPa 0.934), and allowing a cell viability significantly superior to the other groups analysed. To conclude, findings in this study demonstrated that PCL, HANp and PEGDA scaffolds may have promising effects on bone regeneration and might open new insights for 3D tissue substitutes.

Ostreococcus tauri is a simple unicellular green alga representing an ecologically important group of phytoplankton in oceans worldwide. Modern molecular techniques must be developed in order to understand the mechanisms that permit adaptation of microalgae to their environment. We present for the first time in O. tauri a detailed characterization of individual genomic integration events of foreign DNA of plasmid origin after PEG-mediated transformation. Vector integration appears to be random, occurring mainly at a single locus, and thus confirming the utility of this technique for insertional mutagenesis. While the mechanism of double-stranded DNA repair in the O. tauri model remains to be elucidated, we clearly demonstrate by genome resequencing that the integration of the vector leads to frequent structural variations (deletions/insertions and duplications) and some chromosomal rearrangements in the genome at the insertion loci, and often within the vector sequence itself. From these observations, we speculate that a non-homologous end joining-like mechanism is required during random insertion events, as described in plants and other freshwater algal models. PEG-mediated transformation is therefore a promising molecular biology tool, not only for functional genomic studies, but also for biotechnological research in ecologically important marine algae.

Functional articular cartilage regeneration remains an unmet medical challenge, increasing the interest for innovative biomaterial-based tissue engineering (TE) strategies. Hydrogels, 3D macromolecular networks with hydrophilic groups, present articular cartilage-like features such as high water content and load-bearing capacity. In this study, 3D porous polyethylene glycol diacrylate (PEGDA) hydrogels were fabricated combining the gas foaming technique and an UV-based crosslinking strategy. The 3D porous PEGDA hydrogels were characterized in terms of their physical, structural and mechanical properties. Our results showed that the size of the hydrogels pores can be modulated by varying the initiator concentration. In vitro cytotoxicity tests showed that 3D porous PEGDA hydrogels presented high biocompatibility both with human chondrocytes and osteoblast-like cells. Importantly, the 3D porous PEGDA hydrogels supported the viability and chondrogenic differentiation of human bone marrow-derived mesenchymal stem/stromal cells (hBM-MSCs)-based spheroids as demonstrated by the positive staining of typical cartilage extracellular matrix (ECM) (glycosaminoglycans (GAGs)) and upregulation of chondrogenesis marker genes. Overall, the produced 3D porous PEGDA hydrogels presented cartilage-like mechanical properties and supported MSC-spheroid chondrogenesis, highlighting their potential as suitable scaffolds for cartilage TE or disease modelling strategies.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

In this work, we investigated for the first time the complexation of sepiapterin (SP), the natural precursor of the natural essential cofactor tetrahydrobiopterin, that displays mild water-solubility and short biological half-life, with the hydrophobic triacetyl-β-cyclodextrin (TAβCD) to improve its encapsulation within methoxy-poly(ethylene-glycol)-poly(epsilon-caprolactone) (mPEG-PCL) nanoparticles. First, TAβCD-SP complexes were produced by spray-drying of TAβCD/SP binary solutions by utilizing the Nano Spray Dryer B-90 HP. Then, dry powders were characterized by differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FTIR) and transmission and scanning electron microscopy (SEM and TEM, respectively) and compared to the complex components and physical mixtures (PMs). Next, SP was encapsulated within methoxy-poly(ethylene-glycol)-poly(epsilon-caprolactone) (mPEG-PCL) nanoparticles by nanoprecipitation of a SP/TAβCD complex/mPEG-PCL solution. In addition to complex nanoencapsulation, we assessed encapsulation of pure SP by nanoprecipitation with an intermediate step, which comprised the co-drying of SP, TAβCD and mPEG-PCL copolymer solution in organic solvent; this step aimed to promote the formation of molecular interactions between SP, TAβCD and the PCL blocks in the copolymer. SP-loaded mPEG-PCL nanoparticles were characterized by dynamic light scattering (DLS) and SEM. Nanoparticles with size of 74-75 nm and small polydispersity index (PDI <0.1) were obtained when SP-TAβCD equimolar spray-dried complex was used for nanoencapsulation, and SEM analysis indicated the absence of free SP crystals. Moreover, the encapsulation efficiency (%EE) and drug loading (DL) were 85% and 2.6%, respectively, as opposed to those achieved with pure SP encapsulation (14% and 0.6%, respectively). Overall, our results confirm that spray-drying of SP/TAβCD solutions at the appropriate molar ratio leads to the hydrophobization of the relatively hydrophilic SP molecule, enabling its encapsulation within mPEG-PCL nanoparticles.

Most of the commonly used Ionic Liquids (ILs) contain bulky organic cations with suitable anions. With our COMPLET (Concept of Melting Point Lowering due to Ethoxylation), we follow a different approach. We use simple, low-toxic, cheap and commercially available anions of the type Cx(EO)yCH2COO– to liquefy presumably any simple metal ion, independently of its charge. In the simplest case, the cation can be sodium or lithium, but synthesis of Ionic Liquids is also possible with cations of higher valences such as transition or rare earth metals. Anions with longer alkyl chains are surface active and form surface active ionic liquids (SAILs), which combine properties of ionic and nonionic surfactants at room temperature. They show significant structuring even in their pure state, i.e. in the absence of water or any other added solvent.