This article presents a harmonic analysis of the stator currents of a squirrel-cage in-15 duction motor fed by a voltage source inverter with PWM space vector control (SV-PWM). The 16 influence of PWM switching frequency and dead time (dead-band) of controlled transistors on 17 THD and electromagnetic torque ripple is shown. The aim is to determine the lowest switching 18 frequency of the transistors for which the drive will operate correctly. Characteristics were de-19 termined as functions in the form of THD ( ), where the least square approximation was 20 used for stator current measurements when the PWM switching frequency is changed. The ap-21 proximations were realized for simulation and experimental results. To clarify the results, the 22 operation of hardware PWM circuits in microcontrollers was analyzed.

We consider the propagation of electromagnetic waves in the Friedman – Lemaître – Robertson – Walker metric. The exact solutions for plane and spherical wave are written down. The corresponding redshift, amplitude change, and dispersion are discussed. We also speculate about the connection of the electromagnetic wave equation to the Klein–Gordon equation.

The well-known coupling between the magnetic and electric fields in electromagnetic radiation is revisited in light of the recent introduction of a microscopic theory for the Ørsted magnetic field induction. I argue that, if the Ørsted magnetic field induction does indeed have a microscopic origin rather than the continuum solution offered by the Maxwell-Ampere equation, the "electromagnetic wave"' propagating in vacuum will not have a magnetic component.

To realize structural vibration control,a two parameters H2 optimization design was proposed to optimize the tuning ratio and damping ratio for electromagnetic tuned mass damper (EMTMD). The control effect of this two parameters optimization design is better than that of classical tuned mass damper (TMD).For this two parameters optimization,the most important thing is that the inductance of the coil can be set very small and the external load resistance can be positive ,which can avoid the use of complex negative impedance circuit. If Ref.[6] were designed according to the H2 optimization of two parameters, the EMTMD can be used for multi-modal vibration control of structures without connecting negative inductance and negative resistance spontaneously.

Background. This study aims to estimate the rate of death by cancer, according to Radio Base Stations (RBS) radiofrequency exposure, especially for the types of breast, cervix, lung and esophagus cancer. Methods. We collected information about the number of deaths by cancer, gender, age group, Gross Domestic Product per capita, death year and the amount of exposure over the lifetime. We investigated all cancer types and some specific types (breast, cervix, lung and esophagus cancers). Results. In capitals where RBS radiofrequency exposure was higher than 2,000/antennas-year, the average mortality rate was 112/100,000 for all cancers. The adjusted analysis showed that the higher the exposure to RBS radiofrequency, the higher cancer mortality. The highest adjusted risk was observed for cervix cancer (Rate Ratio = 2.18). The spatial analysis showed that the highest RBS radiofrequency exposure was observed in a city in southern Brazil, which also showed the highest mortality rate for all types of cancer and specifically for lung and breast cancer. Conclusion. The balance of our results indicates that the exposure to radiofrequency electromagnetic fields from RBS increases the rate of death by all types of cancer.

The calculation of echo intensity involved in the SAR image simulation is usually based on the electromagnetic formula or approximate formula derived under certain assumptions. However, the parameters used in these formulas are often difficult to obtain, and the formulas have errors with the actual situation. In this paper, a method of embedding deep neural network (DNN) into the simulation process based on ray tracing is proposed, so that the DNN model can be directly used to fit the calculation formula of echo intensity from real SAR images. Simulation results show that this method can obtain SAR images with high similarity.

The direct measurements of the magnetic flux density in steel blocks within Compact Muon Solenoid (CMS) magnet yoke are performed with 22 flux loops installed in selected regions of the yoke. The 10,000-ton CMS magnet flux return yoke encloses a 4 T superconducting solenoid with a 6-m-diameter by 12.5-m-length free bore and consists of five dodecagonal three-layered barrel wheels and four end-cap disks at each end. The yoke steel blocks, mostly up to 620 mm thick, serve as the absorber plates of the muon detection system. A TOSCA 3-D model of the CMS magnet has been developed to describe the magnetic field everywhere outside of the tracking volume which was measured with a field-mapping machine. In the present study, for the first time, the reliable reconstruction of the magnetic flux density in the steel blocks of the yoke is performed using the CMS magnet standard discharges from the operational magnet current of 18.164 kA. To provide this reconstruction, the voltages induced in the flux loops (with amplitudes of 20–250 mV) have been measured with six 16-bit DAQ modules and integrated offline over time. The results of the flux loop measurements during three magnet ramp downs are presented and discussed.

Discovery and development of effective strategies to treat emerging and often drug resistant strains of viral and microbial pathogens presents one of the greatest challenges of the 21st century. Despite nearly a century of progress in developments in antimicrobial and antiviral therapies, infectious diseases still account for a substantial proportion of deaths worldwide, including over 100 million globally in the recent pandemic to date. In recent decades, the plague of antimicrobial resistance also represents an additional and alarming signal for both human and animal healthcare and signals a renewed sense of urgency in addressing this issue. This has made the search for novel classes of antibiotics, antivirals and therapeutics found to be capable of bypassing the microbial and viral resistance mechanisms necessary to in order to replenish our current arsenal of antimicrobial and antiviral drugs and update our therapeutic regimens. In addition, the tremendous impact exerted by viral infections and related pathologies on our lives during the recent decade has forced scientists to acknowledge the opportunities and challenges associated with tackling infectious diseases by developing effective antiviral agents endowed with novel mechanisms of action. The discovery of new antimicrobial/antiviral agents, as well as the repurposing of existing drugs and therapeutic options will be crucial to fight the ever-increasing resistance of “superbugs”, pathogenic fungi, viruses, and parasites. Proponents of modern biophoton therapy proposed in this paper can trace its origins to the Russian scientist Alexander Gurwitsch, who a century ago observed ultra-weak emissions of light emerging from an onion root and soon found additional living tissues to be emanating similar energetic phenomena, thus energizing research which continues to the present day and projected toward the development of useful applications of the new-found biological photonic phenomena. The purpose of the present paper is to introduce the past experiences, potential applications and highly successful outcomes of biophotonic therapy as an option to treat infectious diseases including HIV, Hepatitis C, MRSA, and others, with emphasis on efficacy of using biophotonic therapies to treat and ameliorate the drug resistant variants of the above infectious agents, including potential applications for the current COVID-19 pandemic and in preparation for the emergence of the next epidemic or pandemic.

Mathematics first is a logical system. But, the Mathematics Crisis showed that we cannot have a logical self-consistent mathematics system. Physics is a kind of applied science. It first need be valid to invent new production and understand new observation. In one theory of physics, the studied object is usually defined as an abstract concept. For example, the Sun is defined as a point particle in the Newtonian theory of gravity. In different theories of physics, the abstract concept for a same object is different. It determines that logical self-consistent is not needed for different theories of physics. Physics only can be developed from observation and experiment. But, in the past a century, physicists’ main attempt is to have a standard model, such as the Grand Unification or the Theory for Everything, from mathematics derivation. Therefore, the current attempt to develop new physics is questioned. In recent, the strong gravitational field was studied. It is found that the fundamental physical constants which are measured in the weak field shall be varied in a super strong field. For the two reasons, modern physics need be advanced greatly.

The paper is dedicated to the topical problem of examining permafrost state and the processes of its geocryological changes by means of geophysical methods. To monitor the cryolithozone, we propose and scientifically substantiate a new technique of pulsed electromagnetic cross-well sounding. Based on the vector finite-element method, we created a mathematical model of the cross-well sounding process with a pulsed source in a three-dimensional spatially heterogeneous medium. A high-performance parallel computing algorithm was developed and verified. Through realistic geoelectric models of permafrost with a talik under a highway, constructed following the results of electrotomography field data interpretation, we numerically simulated the pulsed sounding on the computing resources of the Siberian Supercomputer Center of SB RAS. The simulation results suggest the proposed system of pulsed electromagnetic cross-well monitoring to be characterized by a high sensitivity to the presence and dimensions of the talik. The devised approach can be oriented to addressing a wide range of issues related to monitoring permafrost rocks under civil and industrial facilities, buildings and constructions.

The study of the human psyche has elucidated a bipartite structure of logic reflecting the quantum--classical nature of the world. Accordingly, we posited an approach toward studying the brain by means of the quantum--classical dynamics of a mixed Weyl symbol. The mixed Weyl symbol can be used to describe brain processes at the microscopic level and, when averaged over an appropriate ensemble, can provide a link to the results of measurements made at the meso and macro scale. Within this approach, quantum variables (such as, for example, nuclear and electron spins, dipole momenta of particles or molecules, tunneling degrees of freedom, and so on) can be represented by spinors, whereas the electromagnetic fields and phonon modes can be treated either classically or semi-classically in phase space by also considering quantum zero-point fluctuations. Quantum zero-point effects can be incorporated into numerical simulations by controlling the temperature of each field mode via coupling to a dedicated Nos\'e-Hoover chain thermostat. The temperature of each thermostat was chosen in order to reproduce quantum statistics in the canonical ensemble. In this first paper, we introduce a general quantum--classical Hamiltonian model that can be tailored to study physical processes at the interface between the quantum and the classical world in the brain. While the approach is discussed in detail, numerical calculations are not reported in the present paper, but they are planned for future work. Our theory of brain dynamics subsumes some compatible aspects of three well-known quantum approaches to brain dynamics, namely the electromagnetic field theory approach, the orchestrated objective reduction theory, and the dissipative quantum model of the brain. All three models are reviewed.

This work presents an alternative to harnessing wind energy with an Electromagnetic Frequency Regulator (EFR) coupled to a hydrostatic transmission and associated with a horizontal axis wind turbine, a bidirectional frequency inverter and a secondary energy source, in a hybridized system. The hydrostatic transmision is composed by a fixed displacement axial piston pump and a variable displacement, swash plate, axial piston motor. Feedback linearization was used as a technique to control the motor geometric displacement, and a prediction algorithm for the steady state rotations of the armature and the electromagnetic field has been developed. A 5\,kW project was simulated on a Scilab platform, with combinations of constant or variable load, and constant or variable wind speed. The results indicated that the system was able to supply the generator load, adapting to fluctuations in wind speed. The possibility of storing wind energy through the inverter has also been proven. The system can accumulate energy in batteries during the fastest wind regimes, to use it when the turbine power is lower than the load.

Electric and/or magnetic fields are generated by stationary charges, uniformly moving charges and accelerating charges. These field components are described in the literature as static fields, velocity fields (or generalized Coulomb field) and radiation fields (or acceleration fields), respectively. In the literature, the electromagnetic fields generated by lightning return strokes are presented using the field components associated with short dipoles and in this description the one to one association of the electromagnetic field terms with the physical process that gives rise to them is lost. In this paper, we will derive expressions for the electromagnetic fields using field equations associated with accelerating (and moving) charges and separate the resulting fields into static, velocity and radiation fields. The results illustrates how the radiation fields emanating from the lightning channel give rise to field terms varying as inverse of distance and distance squired, the velocity fields generating field terms varying as inverse of distance squired and the static fields generating fields components varying as inverse of distance squired and distance cube. These field components depend explicitly on the speed of propagation of the current pulse. However, the total field does not depend explicitly on the speed of propagation of the current pulse. It is shown that these field components can be combined to generate the field components pertinent to the dipole technique. However, in this conversion process the connection of the field components to the physical process taking place at the source that generate these fields (i.e. static charges, uniformly moving charges and accelerating charges) is lost.

The olfactory system is capable of distinguishing individual odorants from among a virtually unlimited number. Fish, for example, detect changes in the electric field environment induced by prey and other sources. Floral electric fields exhibit variations in pattern and structure, which can be discriminated by bumblebees. We have constructed an electric field sensor, which, in the course of focussing on achieving maximum sensitivity and consistency, ultimately resembles features of the insect sensorium. A “fingerprint” 3D plot ( time, frequency range, voltage amplitude), representing the emitted electric field profile, is presented for each of a variety of odorants and other chemicals. The substance-specific electric-field emission and identification is not impeded by containers or barriers or distance.

This article is a big picture of how electrical noise or conducted Electromagnetic Interference (EMI) is generated and mitigated in power converters. It gives an overview of what EMI in power converters is – from generation through to conduction and mitigation. It is meant to cover the complete subject as a summary so that the reader will have an outline of how to control conducted EMI by design (where possible) and how to mitigate by filtering. A clear distinction is made between Differential Mode (DM) and Common Mode (CM) EMI generation and mitigation. By using a boost converter as an example the trade-offs for DM noise control are discussed. It is shown how CM EMI is generated in a boost converter using the concept of the “Imbalance Difference Model” (IDM). Practical measurements for an in-line power filter is given showing the effect of the filter on the total EMI of a boost converter. Measurements for the CM current produced due to the imbalance difference for different values of the boost conductor are also shown. The main contribution of this study is linking CM noise generation to DM EMI. It is shown that CM noise is a direct consequence of DM noise (although circuit imbalance and coupling to a common ground also play a role). This paper will be useful to designers seeking the “bigger picture” of how EMI is generated in power converters and what can be done to mitigate the noise.

In this work, quantum dynamics of a spin-0 particle under the effects of Lorentz symmetry violation in the presence of Coulombtype non-electromagnetic potential $(S(r) ∝ \frac{1}{r})$ is investigated. The non-electromagnetic (or scalar) potential is introduced by modifying the mass term via transformation $M → M + \frac{η_c}{r}$ in the relativistic wave equation. The linear central potential induced by the Lorentz symmetry violation is a linear radial electric and constant magnetic field and, analyze the effects on the spectrum of energy and the wave function

In the energy-momentum density expressions for a relativistic perfect fluid with a bulk motion, one comes across a couple of pressure-dependent terms, which though well known, are to an extent, lacking in their conceptual basis and the ensuing physical interpretation. In the expression for the energy density, the rest mass density along with the kinetic energy density of the fluid constituents due to their random motion, which contributes to the pressure as well, are already included. However, in a fluid with a bulk motion, there are, in addition, a couple of explicit, pressure-dependent terms in the energy-momentum densities, whose presence to an extent, is shrouded in mystery, especially from a physical perspective. We show here that one such pressure-dependent term appearing in the energy density, represents the work done by the fluid pressure against the Lorentz contraction during transition from the rest frame of the fluid to another frame in which the fluid has a bulk motion. This applies equally to the electromagnetic energy density of electrically charged systems in motion and explains in a natural manner an apparently paradoxical result that the field energy of a charged capacitor system decreases with an increase in the system velocity. The momentum density includes another pressure-dependent term, that represents an energy flow across the system, due to the opposite signs of work being done by pressure on two opposite sides of the moving fluid. From Maxwell's stress tensor we demonstrate that in the expression for electromagnetic momentum of an electric charged particle, it is the presence of a similar pressure term, arising from electrical self-repulsion forces in the charged sphere, that yields a natural explanation for the famous, more than a century old, 4/3 factor in the electromagnetic mass.

Background: biophysical stimulation therapy, and in particular Pulsed Electromagnetic Fields (PEMFs) and capacitively coupled electric fields (CCEFs) has significantly increased in the last twenty years. For this, it is necessary to have clear information regarding the efficacy, the therapeutic indication and the expected objectives. Methods: we conducted a narrative review taking into consideration different types of studies with different areas of application. The objective was to take into consideration and analyze the different fields of use and the relevant information present in the literature. Results: There is unanimous opinion regarding the usefulness of applying biophysical therapy on the bone compartment both in terms of the tissue healing process and the symptoms associated with this situation. Differently, but no less importantly, in the joint compartment positive opinions were observed mainly on the inflammatory and catabolic process, however, at present,we did not report evidence regarding cartilaginous tissue regeneration. Conclusion: the effectiveness of PEMFs and CCEFs on the bone healing process in the Orthopedic and Traumatology fields is consolidated evidence in the literature. We have also found positive results on symptoms and patient compliance with rehabilitation therapies. Therefore, notable application can be envisaged in the fields of Prosthetic Surgery and Sports Medicine.

Coupling the Maxwell tensor to the Riemann-Christoffel curvature tensor is shown to lead to a geometricized theory of electrodynamics. While this geometricized theory leads directly to the classical Maxwell equations, it also extends their interpretation by giving charge density and mass density, and the four-velocity that describes their motion geometric definitions. These geometric definitions are reminiscent of General Relativity’s interpretation of mass in terms of the scalar curvature R and hint at the emergence of gravity. The gravitational theory that does emerge is shown to be equivalent to Einstein’s General Relativity augmented by an energy-momentum tensor term that mimics the properties of dark matter and/or dark energy. In summary, the proposed geometrization of the Maxwell tensor puts both electromagnetic and gravitational phenomena on an equal footing with both being tied to the curvature of space-time. Using specific solutions to the proposed theory, the unification brought to electromagnetic and gravitational phenomena, as well as the relationship of those solutions to the corresponding solutions of the classical Maxwell and Einstein field equations are compared.

The development trends of the modern world of power electronics dictate the requirements for the use of AC voltage converters as soft starters for induction motors. A direct connection of the motors to the mains voltage negatively affects both the motor itself and the mains system as a whole due to high starting currents values, which entail, as a rule, more frequent accidents and shorter the drive system service life. The paper presents a study of the control system of a multi-zone AC voltage regulator. The use of capacitive voltage dividers will also compensate for the consumed reactive power. The article analyzes the features of modern soft starters, describes the circuit design, presents a mathematical calculation by the method of algebraization of differential equations, a performed simulation modeling in Matlab/Simulink, and also an assembled experimental stand for further research. Particular attention is paid to the definition of the multizonality concept of the proposed converter and the analysis of the control method. The developed algorithm of the double-loop automatic control system will minimize the influence of induction motors on the mains voltage, and thus improve electromagnetic compatibility.

Giant plasmonic surface enhancement has been observed in gold coated micron sized inverse pyramids entrapping a gold nanoparticle. The amplification of both surface enhanced Raman and photoluminescence signals was found to be dependent on the diameter of trapped gold nanoparticle and around 50-fold enhancement was detected for 250nm diameter sample relatively to the 50nm one. Finite differential time domain simulations, performed to determine the near-field distribution in the structure, showed that when the nanoparticle protrudes into the hotspot zone of the void, coupling of electromagnetic field occurs and the plasmon-related near-field enhancement is concentrated into the close vicinity of the nanoparticle, mainly into the close gaps around the tangential points of the curved sphere and the flat pyramid surface. This results in a more than 15 times increase of the near-field intensity, compared to the empty void.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

We examine here characteristics of electromagnetic waves that propagate through an unbounded space filled with a homogeneous isotropic chiral medium. Resulting characters are compared to those of the electromagnetic waves propagating through an achiral free space. To this goal, we form energy conservation laws for key bilinear parameters in a chiral case. Due to a nonzero medium chirality, conservation laws turn out to contain extra terms that are linked to the spin-orbit coupling, which is absent for an achiral case. As an example, we take a plane wave for achiral case to evaluate those bilinear parameters. Resultantly, the conservation laws for a chiral case are found to reveal inconsistencies among several bilinear parameters that constitute the con-servation laws , thereby prompting us to establish partial remedies for formulating proper wave-propagation problems.

We propose a new theory beyond the standard model of elementary-particle physics. Employing the concept of a quantized spacetime, our theory demonstrates that the zero-point energy of the vacuum alone is sufficient to create all the fields, including gravity, the static electromagnetic field, and the weak and strong interactions. No serious undetermined parameters are assumed. Furthermore, the relations between the forces at the quantum-mechanics level is made clear. Using these relations, we quantize Einstein’s gravitational equation: Beginning with the zero-point energy of the vacuum, and after quantizing Newtonian gravity equation, we combine the energies of a static electromagnetic field and gravity in a quantum spacetime. Applying these results to the Einstein gravity equation, we substitute the energy density derived from the zero-point energy in addition to redefining differentials in a quantized spacetime. This is how we derive the quantized Einstein gravitational equation without assuming the existence of macroscopic masses. For the weak interaction, by considering plane-wave electron and the zero-point energy, we obtain a wavefunction that represents a β collapse. In this process, from a different point of view than Weinberg-Salam theory, we derive the masses of the W and Z bosons and the neutrino, and we calculate the radius and lifetime of the neutron. For the strong interaction, we previously reported an analytical theory for calculating the mass of a proton by providing a specific linear attractive potential obtained from the zero-point energy, which agrees well with the measurements. In the present study, we further calculate the strong interaction between two nucleons, i.e., the mass of the pi-meson. The resulting calculated quantities agree with the measurements, which verifies our proposed theory.

The combination of interstitial hyperthermia treatment (IHT) with high dose rate brachytherapy (HDR-BT) for prostate cancer treatment and has the potential to improve clinical outcome, since it highly enhances the efficiency of cell kill, especially when applied simultaneously. Therefore, we have developed the ThermoBrachy applicators. To effectively apply optimal targeted IHT, treatment planning is considered essential. However, treatment planning in IHT is rarely applied since it is regarded difficult to accurately calculate the deposited energy in the tissue in a short enough time for clinical practice. In this study, we investigated various time-efficient methods for fast computation of the electromagnetic (EM) energy deposition resulting from the ThermoBrachy applicators. Initially, we investigated the use of an electro-quasistatic solver. Next, we extended our investigation to the application of geometric simplifications. Furthermore, we investigated the validity of the superpositioning principle, which can enable adaptive treatment plan optimization without the need for continuous recomputation of the EM field. Finally, we evaluated the accuracy of the methods by comparing them to the golden standard Finite-Difference Time-Domain calculation method using gamma-index analysis. The simplifications considerably reduced the computation time needed, improving from >12 h to a few seconds. All investigated methods showed excellent agreement with the golden standard by showing a >99% passing rate with 1%/0.5 mm Dose Difference and Distance-to-Agreement criteria. These results allow the proposed electromagnetic simulation method to be used for fast and accurate adaptive treatment planning.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

An efficient design method is proposed for a compact common-mode rejection (CMR) filter utilizing dumbbell-shaped defected ground (DS-DG) structures and gap-coupled stub (GCS) resonators. A CMR filter for differential lines helps to improve the signal integrity of high-speed digital signals on printed circuit boards. The proposed CMR filter design is based on the equivalent circuit models, while the previous designs depended heavily on the DS-DG structure optimization using the EM simulations. The proposed CMR filter effectively reject the common-mode components with minimally affecting the differential signals. To prove the simplified design approach, a 5th-order Chebyshev band-stop filter has been designed with three DS-DG structures and two GCS resonators. From the simulated and measured results, it is found that the proposed CMR filter provides ~90% fractional frequency bandwidth with more than 20 dB of common-mode rejection ratio and less than 0.6 dB of insertion loss of the differential signal.

In this article, an efficient die bonding technology based on silver sintering due to induction heating is presented. By using this technology, the heat for the sintering reaction is locally limited to the bonding area and the heating of the entire power module is avoided. Furthermore, the sintering reaction is promoted due to current flow between the silver particles and the sintering time is drastically reduced. Next to the experimental trials presented in this paper, FE-simulation methods were applied in order to develop a suitable induction coil geometry for the bonding of a diode to a direct bonded copper (DBC) substrate. Additional heating and sintering tests verified the reliability of the simulation model as well as the technological approach. Diodes were successfully bonded during the experiments and were analyzed by means of scanning electron microscopy (SEM) and function tests in order to qualify the inductive bonding technology. The results presented in this paper demonstrate, that induction heating has high potential for cost effective production in the field of die-attach and can drastically increase the output in power electronics production.

Propagation of electromagnetic (EM) waves inside and on the surface of the human body is the subject of active research in area of biomedical applications. This research area is the basis for wireless monitoring of biological object parameters and characteristics. Much attention has been paid to radio-frequency identification systems, which are intended for biomedical applications. Solutions to the following problems are crucial to achieve the stated goals in the area of wireless monitoring: EM wave propagation inside regular and multilayer biological media, through the interface between different media, and on-body surface wave propagation. The biological object monitoring is based on a consideration of the followingprocesses: a) propagation of the EM wave in a biological medium considered as the dielectric with a high dielectric permittivity and substantial conductivity; b) penetration of the EM wave through the biological medium–air interface (wave reflection and refraction); c) propagation of the EM wave in a multi-layer biological medium; d) propagation of the EM wave along the plane or curved surface of biological objects.

The paper presents an analysis of the method of recording the magnetic component of the Earth’s natural pulse electromagnetic field in an urban environment. This method of recording has already proved itself to be a method that allocates the stressed sections of rock mass at mining and, therefore, authors suppose its effectiveness for allocating active tectonic disturbances and forecasting accidents at underground utilities, what will help reduce the potential environmental hazard of these objects.

We would like to suggest that, by considering three virtual gravitational constants assumed to be associated with gravitational, electromagnetic and strong interactions along with a strongly interacting virtual nuclear elementary charge, a workable model of final unification can be developed. In a verifiable approach, Newtonian gravitational constant and Fermi’s weak coupling constant can be interrelated via nuclear and electromagnetic gravitational constants.

Remote patient monitoring systems are helpful since they can provide timely and effective healthcare facilities. Such online telemedicine are usually achieved with the help of sophisticated and advanced wearable sensor technologies. The modern type of wearable connected devices enables the monitoring of vital sign parameters such as: heart rate variability (HRV) also known as electrocardiogram (ECG), blood pressure (BLP), Respiratory rate and body temperature. The ubiquitous problem of wearable devices is power demand for signal transmission, such devices require frequent battery charge which causes serious limitations to the continuous monitoring of vital data. To overcome this, the current study provides a primary report for collecting kinetic energy from human daily activities for monitoring Human vital signs, the harvested energy is used to sustain the battery autonomy of wearable devices, which enables longer monitoring time of vital data. A thorough review of available commercial ECG devices is first provided, and different methods evaluated in other literature to improve the monitoring time of wearable IOT devices. Besides, a novel type of Stress or exercise ECG monitoring device based on Microcontroller PIC18F4550 and Wi-Fi device ESP8266 is proposed in this study, which is cost effective and enables real time monitoring of heart rate on cloud during normal daily activities. In order to achieve both portability and maximum power, the harvester has smallest structure and low friction. Neodymium magnets are chosen for their highest magnetic force. Due to nonlinear magnetic force interaction of the magnets, the nonlinear part of the dynamic equation has inverse quadratic form. Electromechanical damping is considered in this study and the quadratic non linearity is approximated using MacLaurin expansion, which enables to find the law of motion for general case of studies using classical methods for dynamic equations and find the suitable parameters for the harvester. The oscillations are enabled by applying an initial force and there is loss of energy due to the electromechanical damping. A typical numerical application is computed with Matlab software and ODE45 solver is used to verify the accuracy of the method.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

According to Swiss-American Doctor of Sciences and Agricultural Engineer Jean-Pierre Jost, "plants communicate with each other by the quality of light emitted by their leaves or by means of stress hormones and other volatile chemicals. They also make use of cocktails of chemicals, pheromones, shape and colors to attract pollinators whereas other signals repel unwanted organisms. Insects are able to decode such messages and respond accordingly. Plants are apparently also communicating by sounds and electric signals." (1) How do plants do these things? Of course, it's easy to imagine it's all purely mechanical. But at the risk of sounding like a mysticism fanatic, I wonder if plants' activities are part of a spectrum of consciousness that pervades the entire universe. This spectrum would result from everything in the universe having the BITS or BInary digiTS of electronics as their ultimate composition. As explained in this hypothesis, something I call vector-tensor-scalar geometry is essential to my hypothesis. VTS geometry produces the particles of chemicals and pheromones, and refers to communication via electric signals when it speaks of electromagnetic-gravitational interaction. There's another consequence if everything in the universe is ultimately composed of electronic BITS and the cosmos is a spectrum of consciousness/artificial intelligence. It's impossible for an absence of consciousness to exist, either after death or before conception.

Motivated by assumptions that Quantum Mechanics (QM) is not the basement of reality and that additional dimensionality (XD) is required to complete and extend the Standard Models (SM) of Particle Physics and Cosmology, experimental protocols utilizing putative properties of Kaluza-Klein-like (KK) cyclicality embedded within Dirac’s electron hypertube model in conjunction with a Dirac covariant polarized vacuum is developed to produce a new type of low-energy tabletop cross section based on topological phase transitions rather than high energy collision sprays as in the LHC. The model is presented in a highly theoretical axiomatic manner utilizing off-the-shelf parameters generally marginalized by the mainstream physics community. When successful the protocol leads to obsolescence of the highly efficacious 100-year supercollider run producing a paradigm shift with an inherent new set of Unified Field (UF) transformations beyond the Galilean Lorentz-Poincaré transformations of the SM to 3rd regime natural science: Classical – Quantum - UF.

In this article, two elliptical-ovel-shaped cylindrical dielectric resonator based wideband Graphene inspired reconfigurable metasurface absorber is designed on diffused quartz substrate having a relative permittivity of 3.75 and conductivity 2200Kg/m3 with height of 25μm. This metasurface having gold plated ground in microstrip with 5μm which is essential by calculating skin depth at 2.0THz frequency. Two elliptical ovel shaped patches with Graphene plated having built in potential varies 0-2.5eV and relaxation time 1.0ps at 290oK. By changing the relaxation time of Graphene 0.1ps-0.3ps its resonance frequency also varies i.e., reconfigurable property they provide without adding any active i.e., PIN diode components. The proposed MS is designed having a dimension of 100×100μm2 is designed on a microstrip. This MS works in the range of 1.6-2.38THz having more than 90% absorbance with two transmission zero at 2.1THz and 2.3THz having high Q ˃ 50 which is used to determine the sensitivity where the proposed MS used as a sensor to determine hemoglobin (Blood Glucose level) and urine (Uric acid) by changing their refractive index from 1.34-1.43. Maximum sensitivity achieved at 2000GHz/RIU and average sensitivity for hemoglobin and urine sensing achieved 833.33GHz/RIU, FOM-8.33 and 4277.7733GHz/RIU, FOM-555.55 respectively.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

We delve into nonrelativistic quantum electrodynamics within a background magnetic field, ensuring gauge invariance via a vector potential. Our exploration extends to the Lagrangian, which incorporates electron self-interactions and electromagnetic field interactions. Through the path integral formalism, we elucidate the effective action, with a specific focus on the photon propagator and screening effects. Examining density and current components reveals Laurent expansions in the hydrodynamic limit. The equations of motion in real space are derived, leading to discussions on phenomena such as Poiseuille-like flow and the Navier-Stokes equation. To ground our theoretical framework at practical contexts, we consider applications such as the fluid dynamics at binary star systems. Depending on the velocity of the expelled fluid, our analysis allows for both nonrelativistic and relativistic treatments, providing a versatile tool for understanding the intricacies of fluid behavior at astrophysical scenarios. Additionally, we recognize that at the presence of a magnetic field, magnetohydrodynamics becomes crucial. While our current focus is at nonrelativistic quantum electrodynamics, the insights gained here contribute to a broader understanding, offering a comprehensive foundation for quantum electrodynamics analysis at diverse physical systems.