Research results of the relationships between air-volume in air-entrained cement paste, mortar and concrete, all designed according to PN-EN 480-1 guidelines are presented in the paper. The cement paste, mortar and concrete, with w/c=0,5 ratio, were prepared using innovative air-entraining cement CEM II/B-V. The air-entraining cement CEM II/B-V was produced using two methods: mixed together with natural or synthetic aerated admixture. The air volume test of the volumetric method was carried out in case of fresh cement paste, mortar and concrete mix. Fresh concretes were evaluated in terms of stability of air entrainment and consistency for 5, 20 and 40 min. The porosity structure parameters, like summarized air-content, specific surface of air voids, air-voids spacing factor and micropores content of hardened concrete, were estimated using computed tomography with a resolution of 2-5 μm. The aim of the research was to determine the dependence between air-content of cement paste, mortar and concrete on the measurement of air-entrainment of cement paste or mortar with the same w/c ratio and type of cement, all designed according to PN-EN 480-1 guidelines. Test results proved that there is a good correlation between the measured air-content of the cement paste, mortar and concrete. Therefore, it is possible to predict the aeration of concrete on the air-entrainment of the mortar.

To compare The effects of organic and inorganic impregnation on the properties of unmodified, phenol formaldehyde oligomer-modified (PFOMCF), and sodium silicate-modified Chinese fir wood (SSMCF) were compared using samples prepared using the respiratory impregnation method. Impregnation and reinforcement effects and water resistance of PFOMCF and SSMCF were compared and the results was showed that the weight percentage gain, density increase rate, bending strength, and compressive strength of SSMCF were clearly higher than those of PFOMCF and had a lower water absorption rate within 60 h. The impregnation and reinforcement effects and dimensional stability of SSMCF were better than those of PFOMCF. FT-IR, XRD, CONE, and TGA examinations were used to test and analyze the chemical structure, crystalline structure, flame retardancy, and heat resistance of these modified woods. The results indicated that SSMCF possessed more hydrogen bonds than PFOMCF and that Si–O–Si chemical bonding with high bond energy was formed. Meanwhile, the weakened degree of the diffraction peak of SSMCF was much less than that of PFOMCF. These results explained that the mechanical properties and water resistance of SSMCF were better than PFOMCF. Compared with PFOMCF, SSMCF had a lower heat release rate (HRR), peak-HRR, mean-HRR, total heat release, smoke production rate, and total smoke production as well as higher thermal decomposition temperature and residual rate. Inorganic sodium silicate was shown to be a better flame retardant, while SSMCF had good smoke suppression effects, thermal stability, and safety performance in the case of fire.

The area of Central and Eastern Europe, and thus Poland, is not exposed to effects of seismic actions. Any possible tremors can be caused by coal or copper mining. Wind, rheological effects, the impact of other objects or a non-uniform substrate are the predominant types of loading included in calculations for stiffening walls. The majority of buildings in Poland, as in most other European countries, are low, medium-high brick buildings. Some traditional materials, like solid brick (>10% of construction materials market) are still used. But autoclaved aerated concrete (AAC) and cement-sand calcium-silicate (Ca-Si) elements with thin joints are prevailing (>70% of the market) on the Polish market. Adding reinforcement only to bed joints in a wall is a satisfactory solution (in addition to confining) for seismic actions occurring in Poland that improves ULS and SLS. This paper presents results from our own tests on testing horizontal shear walls without reinforcement and with different types of reinforcement. This discussion includes 51 walls made of solid brick (CB) reinforced with steel bars and steel trusses, results from tests on 15 walls made of calcium-silicate (Ca-Si) and AAC masonry units reinforced with steel trusses and plastic meshes. Taking into account our own tests and those conducted by other authors, empirical relationships were determined on the basis of more than 90 walls. They are applicable to design and construction phase to determine the likely effect of reinforcement on cracking stress that damage shear deformation and wall stiffness.

The deterioration of soil-cement in corrosive environment leads to the reduction of strength and the increase of permeability. Effective methods of determining deteriorated layer permeability coefficient of soil-cement are currently lacking. A laboratory test method for permeability coefficient of deteriorated layer was proposed using the modified permeability coefficient testing apparatus. According to the proposed method, the permeability coefficient of deteriorated layer can be obtained after testing the permeability coefficient of the soil-cement specimen in curing room and the equivalent permeability coefficient and deterioration depth of the soil-cement specimen in corrosion environment. Taking the marine dredger fill of Jiaozhou Bay for example, the deteriorated layer permeability coefficients of soil-cements with different cement contents were tested. It turned out that the permeability of deteriorated layer increases with the increase of age. At the beginning of curing age, larger cement content leads to smaller permeability coefficient of the deteriorated layer of soil-cement. As the curing age increases, the deteriorated layer permeability coefficient of the soil-cement with larger cement content becomes larger. The evolution of the permeability coefficient of deteriorated layer with age can be formulated as the Logistic function. This study provides a support for anti-permeability designs of soil-cement structures in corrosive environment.

When focusing on materials science in civil engineering, the current trend is to investigate the use of innovative solutions in order to enhance thermal and energy performances. This trend is amplified with the need for a sustainable development strategy for the construction sector. This paper assesses the integration of a Phase Change Material (PCM) in cement intended for building construction. The key characteristic of PCMs is their capacity to absorb energy and restore it. In building construction, this feature could be harnessed to save energy by incorporating PCMs in the materials used. In this study, passive integration of PCM in cement was tested and thermal properties of such an integration was assessed. The results provide insights into how PCMs affect cement as part of the concrete mixture, thus identifying the contribution of PCM-based cements in concrete mixtures.

Impact load was applied to hardened cement paste (HCP) specimens using a gas gun to investigate microscopic changes in the specimens and develop a better response model of concrete subjected to impact load. Plasma emission was observed at the moment of impact at 420 m/s and the colour of the portion near the impact point turned brighter. This brighter portion was analysed, and it was observed that the pore structure was coarser compared to the other portion; however, the results of thermogravimetry and X-ray diffraction analysis were similar. A possible reason is that the generated heat was instantaneous and the rate of the temperature increase in the HCP decreased due to evaporation of water in the HCP. These results indicate that during impact at a few hundred m/s, porosity increase due to heat effect is more dominant than porosity decrease due to mechanical compaction.

To understand the relationship between water permeability and the pore structure of cementitious materials, literature that studied both water permeability and the pore structure are reviewed, and their correlation is studied. Although the majority of this data is for cement paste, mortar, concrete, and cemented soil are also included. Based on this study, it is established the determination coefficient between water permeability and the total pore volume is very low; however, those between water permeability and the critical, threshold, and median pore diameters, respectively, are moderate. On the other hand, the threshold pore diameter, derived based on the percolation theory, exhibits a very high determination coefficient. The calculated water permeability, using the Katz and Thompson equation, agrees with the reported water permeability quantitatively to a certain level, but is overestimated.

This paper addresses the effect of both microstructure and relative humidity on the long-term creep properties of sustainable calcium carbonate (CaCO₃) cements. Those can be prepared by mixing amorphous calcium carbonate and vaterite with water. A larger starting amount of vaterite, X_V, within the mixture design gives a higher elasticity and resistance to the specimens due to the larger overall bridging area within the newly formed calcite crystals. Regarding creep properties for a given relative humidity, the amplitude of creep strain decreases with X_V, and makes the relation between the elastic modulus, E, and hardness, H, of the samples to be linear with the contact creep modulus, C. On the other hand, for a given composition, the amplitude of creep increases with the relative humidity, making the contact creep modulus, Ci, to rise exponentially with the elastic modulus, E, and hardness, H, of the specimens. The most probable creep mechanisms for this kind of cement seem to be a combination of microcraking in the early stages and dissolution and reprecipitation of calcite in the long-term (also known as pressure solution theory). The presence of water in pores with increasing relative humidity might enhance the local dissolution of calcite, and hence the creep amplitude.

β-dicalcium silicate (β-Ca₂SiO₄, or β-C₂S in cement chemistry notation) is one of the most important minerals in cement. An improvement of its hydration rate would be the key point for developing environmentally friendly cements with lower energy consumption and CO₂ emissions. However, there is a lack of fundamental understanding on the water/β-C₂S surface interactions. In this work we aim to evaluate the water adsorption on three β-C₂S surfaces at the atomic scale using density functional theory (DFT) calculations. Our results indicate that thermodynamically favorable water adsorption takes place in several surface sites, with a broad range of adsorption energies (−0.78 to −1.48 eV), depending on the particular mineral surface and adsorption site. To clarify the key factor governing the adsorption, the electronic properties of water at the surface were analyzed. The partial density of states (DOS), charge analysis, and electron density difference analyses suggest a dual interaction of water with β-C₂S (100) surface: a nucleophilic interaction of the water oxygen lone pair with surface calcium atoms, and an electrophilic interaction (hydrogen bond) of one water hydrogen with surface oxygen atoms. Despite the elucidation of the adsorption mechanism, no correlation was found between the electronic structure and the adsorption energies.

Na-magadiite exchanged with cetyl-trimethylammonium cations provided organophilic silicate materials that allowed the effective removal of the acidic dye "eosin". The organic cations were intercalated into the interlayer spacing of the layered silicate via an exchange reaction between the organic cations from their bromide salt and the solid Na-magadiite at room temperature. Different techniques were used to characterize the effect of the initial concentration of the surfactant on the structure of the organo-magadiites. The C, H, N analysis indicated that a maximum of organic cations of 1.03 mmol/g was achieved at initial concentrations higher than 0.25 mmol/g and was accompanied by an expansion of the basal spacing of 3.15 nm, with a tilted angle of 64.5° to the silicate layers. The conformation of the organic surfactants was probed using solid-state ¹³C, finding mainly the trans conformation similar to that of the starting cetyl trimethylammonium bromide salt (C16TMABr). Thermal gravimetric analysis was carried out to study the thermal stability of the resulting organo-magadiites. The intercalated surfactants started to decompose at 200 °C, with a mass loss percentage of 8 % to 25 %, depending on the initial loading of the surfactant, and was accompanied by a decrease of the basal spacing from 3.20 nm to 2.51 nm, as deduced from the in situ X-ray diffraction studies. At temperatures below 220 °C, an expansion of the basal spacing from 3.15 to 3.35 nm occurred. These materials were used as a removal agent for the anionic dye "eosin". The maximum amount of the dye removed was related to the organic cation content and to the initial concentration of eosin, with an improvement from 2.5 mg/g to 98 mg/g. This value decreased when the organo-magadiite was preheated at temperatures above 200 °C. The regeneration tests indicated that an 85 % removal efficiency was maintained after 6 cycles of use for the organo-magadiites.

3D plotting is an additive manufacturing technology enabling biofabrication, thus the integration of cells or biologically sensitive proteins or growth factors into the manufacturing process. However, most (bio-)inks developed for 3D plotting were not shown to be processed into clinical relevant geometries comprising critical overhangs and cavities, which would collapse without a sufficient support material. Herein, we have developed a support hydrogel ink based on methylcellulose (mc), which is able to act as support as long as the co-plotted main structure is not stable. Therefore, 6 w/v %, 8 w/v % and 10 w/v % mc were allowed to swell in water, resulting in viscous inks, which were characterized for their rheological and extrusion properties. The successful usage of 10 w/v % mc as support ink was proven by multichannel plotting of the support together with a plottable calcium phosphate cement (CPC) acting as main structure. CPC scaffolds displaying critical overhangs or a large central cavity could be plotted accurately with the newly developed mc support ink. The dissolution properties of mc allowed complete removal of the gel without residuals, once CPC setting was finished. Finally, we fabricated a scaphoid bone model by computed tomography data acquisition and co-extrusion of CPC and the mc support hydrogel.

The objective of this study is to investigate the performance of incorporating petroleum sludge waste as raw materials into the cement clinker production. The burnability and the structural analysis of the produced clinker were studied. The results showed that the addition of petroleum sludge into the clinker matrices improved the burnability of the clinker by lowering the free lime content. Moreover, 2.5% and 5% of this waste was effective and did not affect the quality of the cement clinker negatively. This study, which is the first to investigate the incorporation of petroleum sludge into cement production, provides also a complete elimination of this waste from the environment.

Fracture grouting has been a widely used mitigation measure against seepage in the Yellow River Embankment. However, there is currently a lack of systematic investigation for evaluating the anti-seepage effectiveness of fracture grouting employed in this longest river embankment in China. Therefore, in this work, laboratory and in-situ experiments are carried out for investigating the reinforcement effect of fracture grouting in the Jinan Section of the Yellow River Embankment. In particular, firstly, the laboratory tests concentrate on studying the optimum strength improvement for cement-silicate grout by varying the content of backfilled fly ash and bentonite as admixtures. Flexural strength and Scanning Electron Microscope photographs are investigated for assessing the strength and compactness improvement. Subsequently, based on the obtained optimum admixtures content, in-situ grouting tests are carried out in the Jinan Section of the Yellow River Embankment to evaluate the anti-seepage effectiveness of fracture grouting, where geophysical prospecting and pit prospecting methods are employed. Laboratory results show that, compared with pure cement-silicate grouts, the gelation time of the improved slurry is longer and gelation time increases as fly ash content increases. The optimum mixing proportion of the compound cement-silicate grout is 70% cement, 25% fly ash and 5% bentonite, and the best volume ratio is 2 for the investigated cases. Geophysical prospecting using the Ground Penetrating Radar and High Density Resistivity methods can reflect the anti-seepage effectiveness of fracture grouting on site. It shows that the grouting material mainly flows along the axial direction of the embankment. The treatment that is used to generate directional fracture is proved to be effective. The injection hole interval distance is suggested to be 1.2 m, where the lapping effect of the grouting veins is relatively significant. For the investigated cases, the average thickness of the grouting veins is approximately 6.0 cm and the corresponding permeability coefficient is averagely 1.6 × 10⁻⁶ cm/s, which meets the anti-seepage criterion in practice.

Finely ground glass has the potential for pozzolanic reactivity and can serve as a supplementary cementitious material (SCM). Glass reaction kinetics depends on both temperature and glass composition. Microstructural modeling is a helpful approach to get better understanding of cement hydration and microstructure development. Mechanical and performance properties of concrete are directly related to the development of concrete microstructure, which is the consequence of progress in cement hydration. This study initially provides a comprehensive background about cement hydration process and microstructural modeling of the hydration. It then utilizes results of experimental studies, i.e. isothermal calorimetry and thermogravimetric analysis, to find kinetics equation parameters called “Avrami Constants”. For the first time, these constants were found for three main components of cement, i.e. C₃S, C₂S, and C₃A, and also for glass particles smaller than 25 µm. Although modeling of cement hydration and cementitious systems containing single glass particles showed promising results, simulations of combined glass types and sizes showed that more work on microstructural models is needed to properly model the reactivity of mixed glass particle systems.

Concrete consumption greatly exceeds the use of any other material in engineering. This is due to its good properties as construction material and the availability of its components. Nevertheless, the present worldwide construction increase and the high-energy consumption for cement production means a high environmental impact. On the other hand, one of the main problem in iron and steel industry is waste generation and by-products that must be properly processed or reused to promote the environmental sustainability. One of these by-products are blast furnace slag. Cement substitution by slag strategy achieves two goals, raw materials consumption reduction and waste management. In the present work, four different concrete mixtures are evaluated. 25% cement is substituted by different blast furnace slag. Tests are made to evaluate the advantages and drawbacks of each mixture. Depending on the origin, characteristics and treatment of the slag, concrete properties change. Certain mixtures provide proper concrete properties. Stainless steel slag produces a fluent mortar that reduces the water consumption whit a slight mechanical strength loss. Mixture with electric arc slag furnace properties are better to the reference concrete (without slag) when slag is treated similarly to the cement.

In this study, four samples of recycled aggregates from construction and demolition waste of Mexico City were characterized, in order to find innovative uses for this type of materials. Gravel and sand from a recycling plant were analyzed, as well as recycled aggregates in the laboratory from demolished concrete collected in landfills. The characterization was carried out by means of XRD, chemical microanalysis (EDS), pH measurement and sieve analysis. The results reveal that the minerals present in the analyzed materials are triclinic feldspars, cristobalite and pyroxene which correspond to the natural aggregates, as well as variable amounts of calcite, product of the carbonation of the cement paste adhered to these aggregates and in a smaller proportion calcium hemicarboaluminate, rosenhanite and tobermorite. It was determined that the quality (amount of cement) of the original concrete that was recycled, has great influence on the granulometry and the chemical-mineralogical composition of the aggregates, since there will be different quantities and qualities of cement paste adhered to the aggregates of according to size. Finally the pH values measured in all samples fluctuate between 10.15 and 12.08, therefore it is suggested that these materials can be used in soil stabilization.

The availability of new self-sensing cement-based strain sensors allows the development of dense sensor networks for Structural Health Monitoring (SHM) of reinforced concrete structures. These sensors are fabricated by doping cement-matrix materials with conductive fillers, such as Multi Walled Carbon Nanotubes (MWCNTs), and can be embedded into structural elements made of reinforced concrete prior to casting. The strain sensing principle is based on the multifunctional composites outputting a measurable change in their electrical properties when subjected to a deformation. Previous work by the authors was devoted to material fabrication, modeling and applications in SHM. In this paper, we investigate the behavior of several sensors fabricated with and without aggregates and with different MWCNTs content. The strain sensitivity of the sensors, in terms of fractional change in electrical resistivity for unit strain, as well as their linearity are investigated through experimental testing under both static and dynamically varying compressive loadings. Moreover, the responses of the sensors when subjected to destructive compressive tests are evaluated. Overall, the presented results contribute to improving the scientific knowledge on the behavior of smart concrete sensors and to furthering their understanding for SHM applications.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

One source of kaolinite-rich wastes is from mine tailings and the generation of enormous volumes of mine tailings waste is standard practice in this industry. These volumes of waste are, at present, dumped, provoking significant environmental impact and transforming the environment. The impact of storing coal waste requires the study of eco-innovative solutions for the assessment of waste types. The present investigation has the objective of expanding the knowledge on the behavior of new siliceous-aluminum minerals with pozzolanic activity, of added value in the manufacture of similar cements. Four samples were characterized to determine their chemical, morphological and mineralogical composition. The samples were subjected to different thermal activation conditions for the transformation of an inert waste into a material with cementitious properties. XRD analysis have confirmed the total transformation of kaolinite into metakaolinite. The results have shown that after the activation process, the coal refuse presented good pozzolanic activity, meaning that it may be used as a pozzolanic addition in industrial cements, thereby removing high levels of contaminated waste from the environment. In subsequent investigations, research work will continue with the replication of cements with this pozzolanic addition for use in the manufacture of sleepers and slab track railway system.

Background: Lithium di-silicate dental ceramics bonding, realized by using different resins, is strictly dependent on micro-mechanical retention and chemical adhesion. The aim of this in vitro study was to investigate the capability of a 1070 nm fiber laser for their surface treatment. Methods: Samples were irradiated by a pulsed fiber laser at 1070 nm with different parameters (Peak Power from 5 kW to 5 kW, RR 20 kHz, speed from 10 to 50 mm/s, total Energy Density from 1.3 to 27 kW/cm²) and the thermal elevation during the experiment was recorded by a Fiber Bragg Grating (FBG) temperature sensor. Subsequently, the surface modifications were analysed by optical microscope, Scanning Electron Microscope (SEM) and Energy Dispersive X-ray Spectroscopy (EDS). Results: With a Peak Power of 5 kW, RR of 20 kHz and speed of 50 mm/s, the microscopic observation of the irradiated surface showed increased roughness with small areas of melting and carbonization. EDS analysis revealed that, with these parameters, there are no evident differences between laser-processed samples and controls. Thermal elevation during laser irradiation ranged between 5 °C and 9 °C. Conclusions: 1070 nm fiber laser can be considered as a good device to increase the adhesion of Lithium di-silicate ceramics.

The attention to sustainable-related issues has grown fast in recent decades. The experience gained with these themes reveals the importance of considering this topic in the construction industry, which represents an important sector in the world. This work consists on conducting a multicriteria analysis of four cement powders, with the objective of calculating and analysing the environmental, human health and socio-economic effects of their production processes. The economic, technical, environmental and safety performances of the examined powders result from official, both internal and public, documents prepared by the producers. The Analytic Hierarchy Process permitted to consider several indicators (i.e. environmental, human health related and socio-economic parameters) and to conduct comprehensive and unbiased analyses which gave the best, most sustainable cement powder. As assumed in this study, the contribution of each considered parameter to the overall sustainability has a different incidence, therefore the procedure could be used to support on-going sustainability efforts under different conditions. The results also prove that it is incorrect to consider only one parameter to select the ‘best’ cement powder, but several impact categories should be considered and analysed if there is an interest for pursuing different, often conflicting interests.

Electrospinning is the versatile technique to generate large quantities of micro- or nano-fibers from a wide variety of shapes and sizes of polymer. Natural bone is a hierarchically composites with the dispersion of inorganic ceramic along organic polymer. The aim of this study, the electrospun poly (lactic acid) (PLA) mats coated with chitosan (CH) and calcium silicate (CS) powder were fabricated. The morphology, chemical composition, and surface properties of CS/CH-PLA composites were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. In vitro, the CS/CH-coated PLA mats increased the formation of apatite on the surface when soaking in cell cultured medium. During culture, the adhesion and proliferation of the human mesenchymal stem cells (hMSCs) cultured on CS/CH-PLA were significantly promoted relative to those on PLA. Collagen I and fibronectin levels and promoted cell adhesion were observed upon an increase in CS content. Further, compared to PLA mats without CS/CH, CS10 and CS15 mats markedly enhanced the proliferation of hMSCs as well as their osteogenesis properties, which was characterized by bone-related gene expression. Our results demonstrated that the biodegradable and electroactive CS/CH-PLA mats had potential application as an ideal candidate for bone tissue engineering. Together, findings from this study clearly demonstrated that PLLA-C2S composite scaffold may function as an ideal candidate for bone tissue engineering.

Percutaneous vertebroplasty procedure is of major importance, given the significant increasing aging population and higher number of orthopedic procedures related to vertebral compression fractures. Vertebroplasty is a complex technique involving injection of polymethylmethacrylate (PMMA) into the compressed vertebral body for mechanical stabilization of the fracture. Our understanding and ability to modify these mechanisms through alterations in cement material is rapidly evolving. However, the rate of cardiac complications secondary to PMMA injection and subsequent cement leakage has increased with time. The following review considers the main features of PMMA bone cement on the heart, and the extent of influence of materials on cardiac embolism. Clinically, cement leakage results in life-threatening cardiac injury. The convolution of this outcome through an appropriate balance of complex material properties is highlighted via clinical case report.