Interfaces between layers in 3D-printed elements produced by extrusion-based material deposition were investigated on both macro- and micro-scales. On the macro-scale, compression and bend tests were performed on two 3D-printable cement-based compositions (3PCs), namely C1 and C2. The influences of binder composition and time interval between layers on layer-interface strength were critically analyzed. In the context of additive manufacturing, the optimized composition C2, containing pozzolanic additives, exhibited mechanical performance superior to that of the mixture with Portland cement as the sole binder. In particular, Mixture C2 showed a less pronounced decrease in interface tensile strength. Even for time intervals between depositions of two layers as long as 1 day the loss in corresponding flexural strength was below 25%, as compared with C2 specimens tested in the perpendicular direction. In contrast, the decrease in flexural strength measured for C1 specimens amounted to over 90% for the same set of parameters. Higher porosity at the interfaces of the printed concrete layers was identified as the cause for the lower interface strengths of C1. Microscopic observations supported the findings of the macroscopic investigations. While a pronounced recovery (“self-healing”) of the porous, discontinuous interlayers was observed with increasing age for Mixture C2, in case of C1 the filling products grown in the porous interlayer were found to be non-strengthening.

This study identifies new Alkali Activated Composite Mud Mortar to alternate Cement Mortar used for laying masonry works. This study handles both experimental and numerical analysis of strength and durability for mortar, especially bond strength along mortar and brick joints have studied detail and compared with ANSYS. The bond strength has estimated through the triplet brick prism of shear behavior. The strength and deformation characteristics of masonry constituents obtained from these tests depend on the actual composite conduct of masonry. There is always a good reception for environmentally friendly, low energy, new construction materials, and used in preparing mortar/brick unit combinations all around the world. Also, this study fulfills those requirements. Especially, masonry laid with the mud mortar meets all. Fly Ash, Ground Granulated Blast furnace Slag, and Quarry Dust have utilized the new composites' preparation with 8Molority, 10Molority developed excellent strength. The composite specimens are having compression and bond strength, ranging from 4.84-5.14 and 0.12-0.18N/mm2. The mixed ratio of materials has taken (0.5 parts of Fly Ash, 0.5 parts of Steel Slag, 1.75 parts of Soil, and 0.25 parts of Quarry Dust). The samples tested resistance against acidic, sulfate, and alkalinity indicated PH values less than 7 and 9 simultaneously. Compression strength varied from 10-20% and gained more and fit composite used for mortar in masonry works.

To date, Cartesian (x, y, z) coordinate system (CCS) has been the default approach to geometrically specify atomic spatial positions in protein structures since the launch of Protein Data Bank (PDB) in 1971. To this end, this paper proposes a local spherical coordinate system (SCS) approach as an alternative to the default approach and a previously reported global SCS approach. The local SCS approach here requires only two parameters (θ and φ), instead of x, y and z as required by the default CCS approach. Essentially, CCS and SCS are like the two sides of one coin, i.e., geometric coordinate system for three-dimensional position specification. Therefore, this paper furthermore argues that it is time to flip the coin over, and have a look at the other side of the coin, e.g., the local SCS approach, which possesses an intrinsically lower degree of descriptional complexity than that of the default CCS approach, and constitutes a potentially useful alternative perspective for all protein structural research field.

Animal-assisted interventions (AAI) are a unique class of complementary medical treatments that can improve a patient’s quality of life, both physically and psychologically. Part I of this two-paper systematic literature review series focused on the study methods and quantitative results of researchers in this field. We continue this in-depth review here in Part II by discussing the common theories associated with AAI in the context of cancer. Of all the factors at work in human-animal interactions, researchers explicitly cite compatible animal personality, physical touch, physical movement, distraction/entertainment, and increased human interaction as the mechanisms responsible for the positive clinical outcomes observed in AAI. In various combinations, these mechanisms group under broader theoretical frameworks that attempt to fully explain the AAI context as it relates to cancer care. The social support hypothesis and the conception of a human-animal bond are the most referenced overarching frameworks. The cognitive activation theory of stress, the science of unitary human beings, and the self-object hypothesis are also referenced. We briefly consider other relevant theories commonly noted in the human-animal interactions literature that have the potential to clarify aspects of cancer-related AAI. We also discuss the neurobiological transduction mechanisms needed to connect theoretical frameworks and their mechanisms directly to the observed clinical outcomes. To advance the field, researchers should consider overarching theories with testable hypotheses when designing studies, and use consistent terminology when reporting results. This review lays a foundation for progress towards a unified theoretical framework and for effective treatment of the whole cancer patient.

In this paper, we study a generalised CIR process with externally-exciting and self-exciting jumps, and focus on the distributional properties and applications of this process and its aggregated process. The first and second moments of this jump-diffusion process are used to calculate the insurance premium based on mean-variance principle. The Laplace transform of the aggregated process is derived, and this leads to an application for pricing default-free bonds which could capture the impacts of both exogenous and endogenous shocks. Illustrative numerical examples and comparisons with other models are also provided.

Chlorotoxin (CTX) is a 36–amino acid peptide with 8 Cys residues that forms four Cys-Cys bonds. It has high affinity for the glioma-specific chloride channel and matrix metalloprotease-2. Structural and binding properties of CTX analogs with various Cys residue substitutions with L-a-aminobutyric acid (Abu) have been previously reported. Using 4.2 ìs molecular dynamics, we compared the conformational and essential space sampling of CTX and analogs [Abu/Ser^2,19]CTX, [Abu/Ser^5,28]CTX, [Abu/Ser^16,33]CTX, [Abu/Ser^20,35]CTX, and [Abu/Ser^{2,5,16,19,20,28,33,35}]CTX. The native and substituted peptides maintained a high degree of a-helix propensity from residues 8 through 21, with the exception of [Ser^5,28]CTX and [Abu^16,33]CTX. In agreement with previous circular dichroism spectropolarimetry results, the C-terminal b-sheet content varied less from residues 25 through 29 and 32 through 36 and was well conserved in all analogs, except: [Abu^16,33]CTX, [Ser^20,35]CTX, [Abu^{2,5,16,19,20,28,33,35}]CTX, and [Ser^{2,5,16,19,20,28,33,35}]CTX. The Cys¹⁶-Cys³³ and Cys²⁰-Cys³⁵ Cys-Cys bonds appear to be required to maintain the ab-motif of CTX. Their selective substitution with Ser^16,33 however, may mitigate the destabilizing effect of Cys¹⁶-Cys³³ substitution by the formation of an inter residue H-bond from OgH of Ser¹⁶ to OgH of Ser³³ bridged by a water molecule. All peptides shared considerable sampled conformational space, which explains the retained receptor binding of the nonnative analogs.

We present here a theory of Majorana excitons, photo-excited conduction electron-valence band hole pairs, interacting with Majorana Fermions in a Kitaev chain of semiconductor quantum dots embedded in a nanowire. Using analytical tools and exact diagonalisation methods we identify the presence of Majorana Zero Modes in the nanowire absorption spectra.

: This study was aimed at assessing adaptation and bonding of discontinuous (short) glass fiber-reinforced composite to intraradicular dentin EverX Flow (GC Corporation, Tokyo, Japan), when used as intracanal composite filling and anchorage instead of traditional fiber posts. (2) Methods: Seventy intact extracted human teeth were endodontically treated and randomly divided into 6 groups (n=10), depending on the materials used in the post space. In Group 1, a 2-bottle universal adhesive G2 Bond Universal + EverX Flow were tested. In group 2, a single-component universal adhesive G-Premio Bond + EverX Flow were used. In groups 3 and 4 the same materials are tested, but after cleaning of the canal walls with 17% EDTA and final irrigation with 5.25% NaOCl Ultrasound Activated. In the last three Groups (5-7) traditional prefabricated GC Fiber Posts 1.6 mm silanized with G-Multi Primer for 1 minute are cemented with a dual-cured composite resin cement (GradiaCore), after ultrasonic irrigation in the groups 6 and 7. In each group, 1 mm-thick slices from each sample (n=10) were cut for light microscope and SEM inspection for study materials adaption to the dentin and for measuring push-out strength of post / cemement material to the dentin / prefabricated post. These results were statistically analyzed: as the data distribution was not normal, the Kruskal-Wallis Analysis of Variance by Ranks had to be applied. The level of significance was set at p<0.05. Results: Push-out forces varied between 6.66-8.37 MPa. No statistically significant differences were recorded among the groups. Microscopic examination showed that ultrasonic irri-gation increased adaptation of the materials to the dentin surface. There was a trend of higher bond strength among the tested groups when EverX Flow was used. Also, the type of failure was more often cohesive when ultrasonic irrigation and two-step adhesive system were used. Conclusions: Within the limitations of this in vitro study, it may be concluded that when EverX Flow was used for intracanal anchorage in the post-endodontic recon-struction, similar push-out retentive forces and strength to those of traditional fiber posts cemented with particulate filler resin composite cements were achieved. Although further studies are necessary, EverX Flow represents an effective alternative to traditional fiber post adhesion in particular when used in combination with the two-step adhesive system and ultrasonic activation.

As one of the typical deposits in Sichuan-Yunnan-Guizhou Pb-Zn metallogenic province, the Daliangzi Pb-Zn deposit has a close genetic relation with the structural system of “black/fracture zone” formed under the action of NWW-approx. EW strike-slip structures in the metallogenic province, but the mechanism of rock and ore-controlling action of the structural system remains unclear. Based on detailed analysis of tectonite-mineralized alteration lithofacies of R1 “black/fracture zone”, the tectonite-mineralized alteration lithofacies zones can be divided into 4 types in succession outward from the Pb-Zn mineralization center, i.e., ① brecciated and stockwork-like Pb-Zn mineralization-complex breccia facies zone, ② stockwork-like Pb-Zn mineralization-simple breccia and cataclasite facies zone, ③ veined pyrite-sulfide-dolomitic cataclasite facies zone, and ④ fine-veined calcite-black carbonized dolomite facies zone; Cl- and SO42--rich high-temperature oxidizing ore-bearing fluid mixes with reducing fluid in Zone ① while migration and precipitation occur in Zone ④. With the evolution of ore-forming fluid, the homogenization temperature decreases from Zone ① to Zone ④, the salinity increases from Zone ① to Zone ② and then decreases to Zones ③ and ④, and the fluid density has little change on the whole; the contents of Zn, Pb, Cu, Ga, Ge, Cd, Ag, and other metallogenic elements, the Zn/Pb ratio, and the CaO/MgO mole ratio decrease gradually from Zone ① to Zone ④; and REE fractionation, calcilization, silicification, and pyritization enhance gradually from Zone ① to Zone ④. This series of changes are the product of diapirism (cryptoexplosion) of strike-slip structures and “black/fracture zone”, among which the second-order structures (F5, F100, and other faults) derived from NWW-approx. EW striking dextral shear-tension faults F1 and F15 control the brecciated and stockwork-like Pb-Zn mineralized complex breccia facies zones and the stockwork-like Pb-Zn mineralized simple breccia and cataclasite facies zones. Therefore, this paper establishes the zoning mode of tectonite-mineralized alteration lithofacies of “black/fracture zone” and proposes that Zones ① and ② are important prospecting criteria. conclusions.

Considerable attention has been given to the research field of bioorganometallic chemistry, which is a hybrid chemistry field between biology and organometallic chemistry. The introduction of biomolecules, which have hydrogen bonding sites and chiral centers, into organometallic compounds is considered to be a promising strategy to construct chirality-organized bioorganometallic conjugates. This feature paper sketches an outline of induction of helical chirality into bioorganometallic conjugates. Topics covered include control of the helical chirality of 1,n’-disubstituted ferrocene moieties in ferrocene-dipeptide conjugates and the chirality induction of the Au(I)–Au(I) axis in the dinuclear organogold(I)-uracil conjugates.

Rubble stone masonry walls are widely diffused in most of the cultural and architectural heritage of historical cities. The mechanical response of such material is rather complicated to predict due to their composite nature. Vertical compression tests, diagonal compression tests, and shear-compression tests are usually adopted to experimentally investigate the mechanical properties of stone masonries. However, further tests are needed for the safety assessment of these ancient structures. Since the relation between normal and shear stresses plays a major role in the shear behavior of masonry joints, governing the failure mode, triplet test configuration was here investigated. First, the experimental tests carried out at the laboratory (LPMS) of the University of L'Aquila on stone masonry specimens were presented. Then, the triplet test was simulated by using the Total Strain Crack Model, which reflects all the ultimate states of quasi-brittle material such as cracking, crushing and shear failure. The goal of the numerical investigation was to evaluate the shear mechanical parameters of the masonry sample, including strength, dilatancy, normal and shear deformations. Furthermore, the effect of (i) confinement pressure and (ii) bond behavior at the sample-plates interfaces were investigated, showing that they can strongly influence the mechanical response of the walls.

The fusion of surface-modified steel with tungsten carbide (WC) and NiCrBSi powder through laser metal deposition has emerged as a formidable strategy for fortifying components against wear and corrosion in extreme operating environments. Meticulous selection of WC content, innovative pre-alloying techniques, and precise control of laser metal deposition profoundly influence the mechanical properties and microstructural evolution of WC-NiCrBSi coatings applied to surface-enriched commercial alloy steel (805M2, 832M13, and 827M40). These tailored coatings exhibit exceptional resilience, ideal for harsh industrial settings in Oil and gas drilling, petrochemical, and Mining sectors. Advanced materials testing techniques, including scanning electron microscopy, light optical microscopies, and microhardness testing, unveil the innate hardness attributes, with findings highlighting the unassailable fortitude of the Mixed matrix layer's side face. The amalgamation of these testing methodologies with laser metal deposition promises an unparalleled path to extend the operational lifespan of critical components in challenging working conditions. The research horizon for WC-NiCrBSi coatings remains broad, with the potential to enhance durability, operational efficiency, and cost-effectiveness across diverse applications.

In this work, a novel single crystal (3-(4-chlorophenyl)-4,5-dihydroisoxazol-5-yl)methyl benzenesulfonate has been synthetized via a one-pot sequential strategy under sonication. A single crystal X-ray diffraction analysis was reported. In the crystal, a layer structure is generated by C—H···O and C—H···N hydrogen bonds. A Hirshfeld surface analysis indicates that the most important contributions to the crystal packing are from H···H (28.9%), H···O/O···H (26.7%) and H···C/C···H (15.8%) interactions. The optimized structure calculated using density functional theory at the B3LYP/6–311 G+(d,p) level is compared with the experimentally determined structure in the solid state. The calculated highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy gap is 4.6548 eV.

Fluorinated compounds and co-enzymes are being widely researched and employed throughout research community because of their versatile physical, chemical and biological properties. In this work, we synthesized NiS-NiO/S-g-C3N4, a highly effective photocatalyst for C(sp3)-F bond activation and the regeneration of coenzyme (1,4-NADH) employing a new and ecologically acceptable route. The obtained photocatalyst exhibited important photocatalytic properties, such as good solar light harvesting ability, suitability of the optical band-gap, and facilitating efficient charge migrations. As a result, the newly designed NiS-NiO/S-g-C3N4 photocatalyst shows the excellent yield for regenerations of 1,4-NADH (51%). Further, a method of combining C(sp3)-F bond activation with photocatalysis has been demonstrated that represents a very powerful and sustainable approach, that can be a major breakthrough for the field of pharmaceutical.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

The purpose of water treatment through ultraviolet (UV) radiation is to interrupt the development and multiplication of microorganisms by preventing their growth and reproduction.Ultraviolet treatment has become a very affordable solution to produce clean water of optimal quality in regions where access to drinking water is essential. The experimental water treatment unit is powered by a photovoltaic (PV) source. It incorporates a discharge lamp used to generate ultraviolet radiation, which is harnessed to address bacteriological issues related to water quality. This lamp is continuously powered by a photovoltaic (PV) source through an inverter and an electronic ballast. The water treatment system also includes a motor pump designed to draw contaminated water from the input reservoir, a flow control valve to adjust flow rates as needed, and a filter aimed at enhancing the quality of the contaminated water. The water circulates between the input reservoir (contaminated water) and the output reservoir (treated water) through the UV lamp. The relationship between the intensity of the UV lamp and the water flow rate can ensure an adequate water quality.

The quinoline derivative, N-(7-chloro-4-morpholinoquinolin-2-yl)benzamide, was synthesized in a conventional three-step procedure from 4,7-dichloroquinoline using N-oxidation reaction/C2-amidation reaction/C4 SNAr reaction sequence. The structure of the compound was fully characterized by FT-IR, 1H‐, 13C-NMR, DEPT-135°, and ESI-MS techniques. Its physicochemical parameters (Lipinski’s descriptors) were also calculated using the online SwissADME database. Such derivatives are relevant therapeutic agents exhibiting potent anticancer, antibacterial, antifungal, and antiparasitic properties.

Various factors, such as uncertainty of component parameters and uncertainty of sensor meas-urement values, contribute to the difficulty of fault detection in the landing gear retrac-tion/extension hydraulic system. In this paper, we introduce linear fractional transformation technology and uncertainty analysis theory for the construction of the diagnostic bond graph of the landing gear retraction/extension hydraulic system. In this way, interval analytical redundancy relations and fault signature matrix can be derived. Using the fault signature matrix, existing faults of the system can be preliminarily detected and isolated. Additionally, interval analytical re-dundancy relations can be used to detect system faults in detail, and cases analysis can be carried out to determine if the actuator is externally or internally leaky, and if the landing gear selector valve is reversing stuck. Compared to the traditional analytical redundancy relations, this method takes into account the negative factors of uncertainty; and compared to the traditional absolute diagnostic threshold, the interval diagnostic threshold is more accurate and sensitive.