Supplier selection is one of the most important multi criteria decision making (MCDM) problems for decision makers in competitive market. Organizations of today’s world are seeking new ways to reduce negative effects of their organizations to the environment and to reach a greener system. At this point, green supplier selection concept has gained great importance with its ability on incorporating environmental or green criteria into the classical supplier selection practices. Therefore, in this study, it is aimed at proposing a multi-phase MCDM model based on Best-Worst Method (BWM) and interval type-2 fuzzy technique for order preference by similarity to ideal solution (TOPSIS). A case study in a plastic injection molding facility in Turkey is performed to show the applicability of the proposed integrated methodology. The paper ensures insights into the decision making, methodology, and managerial implications. Results of the case study are examined and suggestions for future research are provided.

The microstructure evolution and grain refinement kinetics of a solution treated Cu – 0.1Cr – 0.06Zr alloy during equal channel angular pressing (ECAP) at a temperature of 673 K via route B_C were investigated. The microstructure change during plastic deformation was accompanied by the microband formation and an increase in the misorienations of strain-induced subboundaries. The refinement of initial coarse grains was considered as a result of continuous dynamic recrystallization. The dynamic recrystallization kinetics was discussed in terms of grain/subgrain boundary triple junction evolution. The strain dependence of the triple junctions of high-angle boundaries can be expressed by a modified Johnson-Mehl-Avrami-Kolmogorov relationship with a strain exponent of about 1.49. Severe plastic deformation by ECAP led to substantial strengthening of the Cu-0.1Cr-0.06Zr alloy. The yield strength increased from 60 MPa in the initial state to 445 MPa after the total strain of 12.

The negative impact of the modern-day lifestyle on the environment is aggravated during the COVID-19 pandemic through the increased use of single-use plastics from food takeaways to medical supplies. Similarly, the closure of food outlets and disrupted supply chains have also resulted in significant food wastage. As the pandemic rages on, the aggravation of increased waste becomes an increasingly urgent problem that threatens the biodiversity, ecosystems, and human health worldwide through pollution. While there are existing methods to deal with the organic and plastic waste, many of the solutions also cause additional problems. Increasingly proposed as a natural solution to man-made unnatural problems, there are insect solutions for dealing with the artificial and organic waste products towards a circular economy, making the use of natural insect solutions commercially sustainable. This review discusses the findings and how some of these insects, particularly the Hermetia illucens, Tenebrio molitor, and Zophobas morio, can play an increasing important role in food and plastics, with a focus on the latter.

This paper describes a new approach that can be used to determine the mechanical properties of unknown materials and complex material systems. The approach uses inverse finite element modelling (FEM) accompanied with a designed algorithm to obtain the modulus of elasticity, yield stress and strain hardening material constants of an isotropic hardening material model, as well as the material constants of the Drucker-Prager material model (modulus of elasticity, cap yield stress and angle of friction). The algorithm automatically feeds the input material properties data to finite element software and automatically runs simulations to establish a convergence between the numerical loading-unloading curve and the target data obtained from continuous indentation tests using common indenter geometries. A further module was developed to optimise convergence using an inverse FEM analysis interfaced with a non-linear MATLAB algorithm. A sensitivity analysis determined that the dual Spherical and Berkovich (S&B) approach delivered better results than other dual indentation methods such as Berkovich and Vickers (B&V) and Vickers and Spherical (V&S). It was found that better convergence values can be achieved despite a large variation in the starting parameter values and / or material constitutive model and such behaviour reflects the uniqueness of the dual S&B indentation in predicting complex material systems. The study has shown that a robust optimization method based on a non-linear least-squares curve fitting function (LSQNONLIN) within MATLAB and ABAQUS can be used to accurately predict a unique set of elastic plastic material properties and Drucker-Prager material properties. This is of benefit to the scientific investigation of properties of new materials or obtaining the material properties at different location of a part which might be not be similar due to manufacturing processes (e.g. different heating and cooling rates at different locations).

In this review, severe plastic deformation (SPD) is considered as a materials processing technology. The deformation mode is the principal characteristic differentiating SPD from common forming operations. For large plastic strains, deformation mode depends on the distribution of strain rates between continuum slip lines and can be varied from pure shear to simple shear. A scalar, invariant and dimensionless coefficient of deformation mode is introduced as a normalized speed of rigid rotation. On this basis, simple shear provides the optimum mode for structure modification and grain refinement whereas pure shear is "ideal" for forming operations. Special experiments and SPD practice confirm this conclusion. Various techniques of SPD are classified and described in accordance with simple shear realization or approximation. It is shown that correct analyses of the processing mechanics and technological parameters are essential for comparison of SPD techniques and the development of effective industrial technologies.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

: Microplastics and nanoplastics (MNPs) are becoming an increasingly severe global problem due to their widespread distribution and complex impact on living organisms. Apart from their environmental impact, the effects of MNPs on living organisms have also continued to attract attention. The harmful impact of MNPs has been extensively documented in marine invertebrates and larger marine vertebrates like fish. However, the research on the toxicity of these particles on mammals is still limited, and their possible effects on humans are poorly understood. Considering that MNPs are commonly found in food or food packaging, humans are primarily exposed to them through ingestion. It would be valuable to investigate the potential harmful effects of these particles on gut health. This review focuses on recent research exploring the toxicological impacts of micro- and nanoplastics on the gut, as observed in human cell lines and mammalian models. Available data from various studies indicate that the accumulation of MNPs in mammalian models and human cells may result in adverse consequences, in terms of epithelial toxicity, immune toxicity, and disruption of gut microbiota. The paper also discusses the current research limitations and prospects in this field, aiming to provide a scientific basis and reference for further studies on the toxic mechanisms of micro- and nanoplastics.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

The rapid increasing rate of soil and water bodies pollution is the main anthropogenic effect caused by the mismanagement of post-consumer plastics. This research evaluated the effectiveness of cattail (Typha Latifolia) fibers (CFs) as bio-adsorbents of microplastic particles (MPPs) from wastewater. The effect of the adsorption environment composition on the adsorption rate was investigated. Batch tests were conducted to evaluate the “spontaneous” adsorption of MPs onto CFs. Five MPPs materials (PVC, PP, LDPE, HDPE, and Nylon 6) were evaluated. An industrial wastewater (PW) and Type II Distilled Water (DW) were employed as adsorption environments. The batch tests results show that CFs are effective in removing MPPs from DW and PW. However, higher removal percentage of MPPs were obtained in PW, ranging from 89% to 100% for PVC, PP, LDPE, and HDPE; while the adsorption of Nylon 6 increased to 29.9%, a removal increased of 50%. These observations indicate that hydrophobic interactions drive the “spontaneous and instantaneous” adsorption process and that adjusting the adsorption environment effectively enhances the MPPs removal rate. This research demonstrates the important role that bio-substrates can play in reducing the environmental pollution as efficient, sustainable, low cost, and reliable adsorbents for the removal of MPPs from wastewaters.

Although distributed additive manufacturing can provide high returns on investment the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by 3-D printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here provides for precise controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built and tested for its ability to provide high tolerance thermopolymer pellets from a number of sizes capable of being used in a FGF printer. In addition, the chopping pelletizer is tested for its ability to chop multi-materials simultaneously for color mixing and composite fabrication as well as precise fractional measuring back to filament. The US$185 open-source 3-D printable pelletizer chopper system was successfully fabricated and has a 0.5 kg/hr throughput with one motor, and 1.0 kg/hr throughput with two motors using only 0.24 kWh/kg during the chopping process. Pellets were successfully printed directly via FGF and indirectly after being converted into high-tolerance filament in a recyclebot.

Alternative fuels available at low cost, friendly to natural environments and meet the energy needs and demands, have witnessed a growing demand and use today. Ethanol is an attractive renewable energy source with a high content of oxygen. Ethanol can be produced through ethanolisis, however for this work direct blending of conventional diesel, waste plastic pyrolysis oil and ethanol with commercial fuel improver CI-0808 purchased from Innospec company was attempted. The primary purpose of adding a cetane improver was to improve the combustion characteristics of the blends by at least 1- 3 ignition quality points. Five mixing ratios were chosen in the following order, 50:25:25, 60: 20:20, 70: 15:15, 80: 10:10 and 90: 5:5 for Waste Plastic Pyrolysis Oil (WPPO), ethanol and conventional diesel (CD) respectively. However, for the fuel additive mixing ratio the total volume percentage was considered and the ratio put at 0.01% of the total quantity of blended fuel. In this work WPPO, diesel blends and fuel additives improvers were used as alternative fuel. This was to evaluate their performance and emission characteristics in a stationary single cylinder water cooled experimental diesel engine. The CI-0808 was added due to its potential power to reduce emissions of CO, UHC, NO_X, PM and improved engine performance. The results obtained were compared carefully to ASTM standards and discussed using graph curves figures and tabulated values. The conclusion was that ethanol and WPPO blends can be used in diesel engines as alternative fuel without modification. Used in combination with cetane improvers the emissions reduce significantly and performance improved equalling that of conventional diesel fuel.

The seismic damage in reinforced concrete bridges is identified in this study using the "M and P" hybrid technique initially developed for planar frames. The proposed methodology involves a series of pushover and instantaneous modal analyses with a progressively increasing target deck displacement along the longitudinal direction of the bridge. From the results of these analyses, the diagram of the instantaneous eigenfrequency of the bridge, ranging from the health state to near collapse, is plotted against the inelastic seismic deck displacement. By pre-determining the eigen-frequency of an existing bridge along its longitudinal direction through "monitoring and frequency identification", the target deck displacement corresponding to the damage state can directly be found from this diagram. Subsequently, the damage can be identified by examining the results of the pushover analysis at the step where the target deck displacement is indicated. The effectiveness of this proposed technique is evaluated in the context of multiple span bridges with unequal pier heights, illustrated through an example of a four-span bridge. The findings demonstrate that the damage potential in bridge piers can be successfully identified by combining the results of a monitoring process and pushover analysis.

The inherent value and use of hydrocarbon from waste plastics and solvents can be extended through open-loop chemical recycling as this process converts plastic to range of non-plastic materials. This process is enhanced by first creating plastic-solvent-combinations from multiple sources which are then streamlined through single process stream. We report on the relevant mechanics for streamlining industrially relevant polymers such as polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE) and acrylonitrile butadiene styrene (ABS) into chemical slurries mixed with various organic solvents such as toluene, xylene and cyclohexane. The miscibility of the polymer feedstock within the solvent was evaluated using the Relative Energy Difference method, and the dissolution process was evaluated using the “Molecular theories in a continuum framework” model. These models were used to design a batch process yielding 1 tonne/h slurry by setting appropriate assumptions including constant viscosity of solvents, disentanglement-controlled dissolution mechanism and linear increase of the dissolved polymer’s mass fraction over time. Solvent selection was found to be the most critical parameter for the dissolution process. The characteristics of the ideal solvent are high affinity to the desired polymer and low viscosity. This work serves as a universal technical guideline for open-loop chemical recycling of plastics avoiding the growth of waste plastic in a circular economy framework.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

This paper conducts an extensive literature review focusing on the utilisation of crack tip plasticity as a crucial parameter in determining and enhancing crack growth models. The review encompasses a comprehensive analysis of various methodologies, predominantly emphasising numerical simulations of crack growth models while also considering analytical approaches. Although experimental investigations are not the focus of this review, their relevance and interplay with numerical and analytical methods are acknowledged. The paper critically examines these methodologies, providing insights into their advantages and limitations. Ultimately, this review aims to offer a holistic understanding of the role of crack tip plasticity in the development of effective crack growth models, highlighting the synergies and gaps between theoretical, experimental, and simulation-based approaches.

Keywords: Pulp cell, Periodontal cell, Micro-Arc Oxidation (MAO), Sever Plastic deformation (SPD), Equal Channel Angular Pressing (ECAP), AlamarBlue, ELISA, trypsin

In this paper we describe many important aspects connected with lubricants, namely: the most cheapest organic lubricant in the word, how effectively save lubricant between pairs of friction, what kind of rational shapes for the lubricant must be, what it will be connected with wear and tear using the new organic lubricant (for this purpose formulas and curves are shown in computer program MathCad with calculation). Moreover, there is one physical model which helps to catch car exhausted gases. In conclusion, some recommendations will be given to realize them into the practice during the operation for the different mechanisms including ecology.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

The effectiveness of a recently proposed methodology in the identification of damage in planar, multi-storey, Reinforced Concrete (RC) moment-frames, which develop a plastic-yield mechanism on their beams, is showcased here via the examining of a group of such existing multi-storey frames with three or more unequal spans. According to the methodology, the diagram of the instantaneous Eigen-Frequencies of the frame in the nonlinear regime is drawn as a function of the inelastic seismic roof displacement by performing a sequence of pushover and instantaneous modal analyses with gradually increasing target displacement. Using this key-diagram, the locations of severe seismic damage in an existing moment-frame can be evaluated if the instantaneous fundamental eigen-frequency of the damaged frame, at an analysis step within the nonlinear area, is known in advance by “the monitoring and the identification of frequencies” using a local network of uniaxial accelerometers. This is a hybrid technique because both procedures, the instrumental Monitoring of the structure and the Pushover analysis on the frame (M and P technique), are combined. Moreover, the damage image of the planar multi-storey moment-frame is illustrated, and the lateral stiffness matrix of the damaged frame is calculated with high accuracy.

The time-dependent behavior and long-term stability of deep-buried tunnels in soft rocks have received lots of considerations in tunnel engineering and allied sciences. To better explore and deepen the engineering application of rock creep, extensive research studies are still needed, although fruitful outcomes have already obtained in many related investigations. In this article, the Weilai Tunnel in China’s Guangxi province is studied taking its host rocks as the main research object. In fact, aiming at forecasting the time-varying deformation of this tunnel, a novel elasto-visco-plastic creep constitutive model with two variants is proposed, by exploiting the typical complex load-unload process of rock excavation. The model is well validated and good agreements are found with the relevant experimental data. Moreover, the time-dependent de-formation rules are properly established for the surrounding rocks, by designing two new closed-form solutions based on the proposed creep model and the Hoek-Brown criterion. The convergence deformations calculated from the closed-form solutions conform well to the on-site monitoring data. In only 27 days after excavation, the creep deformation of the Weilai tunnel overtakes 400 mm, which is enormous. To guarantee the long-term stability of this tunnel, a ro-bust support scheme and its long-term monitoring with appropriate remote sensors are strongly suggested.

The study presented hereafter shows a new methodology to reveal traces of polyethylene (the most common microplastic particles, known as a structure of C2H4) in a sample of ocean water by the irradiation of a 50 keV, 1 µA electron beam. This is performed by analyzing the photon (produced by the electrons in water ) fluxes and spectra (i.e. fluxes as a function of photon energy) at different types of contaminated water with an adequate device and in particular looking at the peculiar interactions of electrons/photons with the potential abnormal atomic hydrogen (H), oxygen (O), carbon (C), phosphorus (P) compositions present in the water, as a function of living and not living organic organisms with a PO4 group RNA/DNA strands in a cluster configuration through a volumetric cells grid.