Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Impact of Nitrogen Foamed Stimulation Fluids Stabilized by Nanoadditives on Reservoir Rocks of Hydrocarbon Deposits

Gray cast iron is one of the most important engineering materials that has many applications in various industries including automotive and machinery manufacturing due to its mechanical properties, wear resistance, machining potentials and low price. In this research effect of adding aluminum and silicon to composition of gray cast iron on microstructure and wear resistance was studied. Moreover, it was investigated the role of formation of Fe-Al-Si intermetallic compound in final properties of the alloy. For studying wear resistance of samples pin-on-disc method was carried out. The results showed that addition of aluminum to gray cast iron causes formation of ferrite matrix, which leads to a decrease in hardness value. Increasing silicon content up to 2 wt. % in cast iron with 4 wt. % aluminum intensifies the formation of ferrite matrix, while further increase to 3 wt. % causes emerging a Fe-Al-Si intermetallic phase. Improvement in hardness value was achieved by increasing silicon content from 3 wt. % to 4 wt. % due to the increased percentage of intermetallic phase. Effect of intermetallic phase on decreasing wear rate was showed by studying microstructure and hardness values, however the lowest wear resistance was observed in aluminum bearing cast iron containing 2 wt. % silicon.

Construction projects are usually operating in a complex and dynamic environment in which the accumulation of many interrelated factors causes high uncertainty. Construction projects are complex and frequently involve substantial uncertainties including process complicatedness, intricate organization structure, dynamic environment, and financial strain. The study aims to categorize the influencing factors into three groups, namely construction project system, economic-market climate, and external environment. It attempts to adopt a novel analysis tool to examine the relationship between the project cost and multiple influencing factors by using Bayesian SEM. While the Bayesian SEM method has been receiving increasing attention in exploring the relationship between latent variables, construction studies still heavily rely on the covariance-based SEM approach. This study introduces several advantages of Bayesian SEM that make it more flexible and powerful than covariance-based SEM and provides the foundation of Bayesian SEM estimation and inference by illustrating this method in a project cost application.

Construction projects are usually operating in a complex and dynamic environment in which the accumulation of many interrelated factors causes high uncertainty. Construction projects are complex and frequently involve substantial uncertainties including process complicatedness, intricate organization structure, dynamic environment, and financial strain. The study aims to categorize the influencing factors into three groups, namely construction project system, economic-market climate, and external environment. It attempts to adopt a novel analysis tool to examine the relationship between the project cost and multiple influencing factors by using Bayesian SEM. While the Bayesian SEM method has been receiving increasing attention in exploring the relationship between latent variables, construction studies still heavily rely on the covariance-based SEM approach. This study introduces several advantages of Bayesian SEM that make it more flexible and powerful than covariance-based SEM and provides the foundation of Bayesian SEM estimation and inference by illustrating this method in a project cost application.

Stabilized un-doped Zinc Telluride (ZnTe) thin films were grown on glass substrates under vacuum using closed space sublimation (CSS) technique. A dilute copper nitrate solution (0.1/100 ml) was prepared for copper doping known as ion exchange process in the matrix of ZnTe thin film. The reproducible polycrystalline cubic structure of undoped and Cu doped ZnTe thin films with preferred orientation (111) was confirmed by X-rays diffraction (XRD) technique. Lattice parameter analyses verified the expansion of unit cell volume after incorporation of Cu species into ZnTe thin films samples. The micrographs of scanning electron microscopy (SEM) were used to measure the variation in crystal sizes of samples. The energy dispersive X-rays was used to validate the elemental composition of undoped and Cu-doped ZnTe thin films. The bandgap energy 2.24 eV of ZnTe thin film decreased after doping Cu to 2.20 eV may be due to the introduction of acceptors states near to valance band. Optical studies showed that refractive index was measured from 2.18 to 3.24 whereas thicknesses varied between 220 nm to 320 nm for un-doped and Cu doped ZnTe thin film respectively using Swanepoel model. The oxidation states of Zn⁺², Te⁺² and Cu⁺¹ through high resolution X-ray photoelectron spectroscopy (XPS) analyses was observed. The resistivity of thin films changed from ~10⁷ Ω-cm for undoped ZnTe to ~1 Ω-cm for Cu-doped ZnTe thin film, whereas p-type carrier concentration increased from to respectively. These results predicted that Cu-doped ZnTe thin film can be used as an ideal, efficient and stable intermediate layer between metallic and absorber back contact for the heterojunction thin film solar cell technology.

The acylation of unsymmetrical N-benzylbispidinols in aromatic solvents without external base led to formation of supramolecular gels, which possess different thickness and stability depending on the substituents in para-positions of benzylic group and nature of acylating agent as well as on the nature of the solvent used. Structural features of the native gels as well as of their dried forms were studied by complementary techniques including FT IR- and ATR-spectroscopy, AFM, TEM, SEM, SAXS. Structures of the key crystalline compounds were established by X-ray diffraction. Analysis of obtained data allowed speculating on the crucial structural and condition factors that governed the gel formation. The most important factors were: (i) absence of base, either external or internal; (ii) presence of HCl; (iii) presence of carbonyl and hydroxyl groups to allow hydrogen bonding; (iv) presence of two (hetero)aromatic rings at both sides of the molecule. The hydrogen bonding involving amide carbonyl, hydroxyl at 9th position and, very probably, ammonium N-H+ and Cl- anion appear to be responsible for the formation of infinite molecular chains required for the first step of gel formation. Subsequent lateral cooperation of molecular chains into fibers occured, presumably, due to the aromatic pi-pi-stacking interactions. sc-CO2 drying of the gels gave rise to aerogels morphology different from that of air dried samples.

The Cordoba Guitar Festival is one of the most important cultural events in Spain. This article analyses the musical preferences, satisfaction, attitudinal loyalty and behavioural loyalty of spectators who attended the 36th festival held in July 2016, as well as the festival’s economic impact on the city. To achieve this aim, a structural equation model (SEM) was used. The results show the goodness-of-fit of the model and indicate that the observed data fit the expected dataset.

The incorporation of plastic matrix composite materials into structural elements of the aeronautical industry requires contour machining and drilling processes along with metallic materials prior to final assembly operations. These operations are usually performed using conventional techniques, but they present problems derived from the nature of each material that avoid implementing One Shot Drilling strategies that work separately. In this work, the study focuses on the evaluation of the feasibility of Abrasive Waterjet Machining (AWJM) as a substitute for conventional drilling for stacks formed of Carbon Fiber Reinforced Plastic (CFRP) and aluminum alloy UNS A97050 through the study of the influence of abrasive mass flow rate, traverse feed rate and water pressure in straight cuts and drills. For the evaluation of the straight cuts, Stereoscopic Optical Microscopy (SOM) and Scanning Electron Microscopy (SEM) techniques are used inspection techniques have been used. In addition, the kerf taper through the proposal of a new method and the surface quality in different cutting regions have been evaluated. For the study of holes, the macrogeometric deviations of roundness, cylindricity and straightness have been evaluated. Thus, this experimental procedure reveals the conditions that minimize deviations, defects, and damage in straight cuts and holes obtained by AWJM.

This study measures key indicators of perceived precarity and decent working conditions and their relative effects on life satisfaction of workers in small and medium-sized enterprises. Using a random sample survey, we interviewed 103 workers in four districts of Sylhet division in Bangladesh. Utilizing Smart PLS application for structural equation modeling, we iterated the samples 1000 times which resulted in a new sample size standing at 499. We used a Likert-type five-point scaling technique, with appropriate items related to the latent constructs of the model, for path analysis. We found perceived precariousness has the highest causal relations with a path coefficient of 0.706 with social dialogue (an indicator of decent working conditions) followed by 0.539 with working hour issue, 0.345 with life satisfaction and 0.301 with the unacceptable work issue. The importance-performance map analysis confirms that perceived precarity is the most critical construct for worker’s life satisfaction. Thus, in a ceteris paribus situation, an increase of one point in the performance on the perceived precarity is expected to increase in the performance on the life satisfaction by a total effect level of 0.428. Therefore, we recommend further attention should be paid by the policymakers to the issue of consciousness of the precarity at the workplace for a better life satisfaction of workers.

Village development aims to improve the welfare of villagers and the quality of human life. The purpose of this study was to formulate a coastal tourism management model toward developing independent tourist village. This study employed a quantitative approach by using survey methods. The data analysis was performed by using Structural Equation Modeling (SEM). There were 4 variables namely: the potential of mangrove ecosystem, the perception of coastal community, the coastal tourism facilities, and the coastal ecotourism. The results indicated that there were 2 variables which had a significant effect on the management of coastal tourist village namely the perception of coastal community and coastal ecotourism. Furthermore, the management of coastal tourist village had a significant effect on the development of independent tourist village, and the management of coastal tourist village was a strong mediator to develop an independent coastal tourist village.

1) Background: Traditionally, complex biological products such as vaccines presented unique challenges to implementation of even rudimentary characterization packages; thus, the product was defined almost exclusively by its manufacturing process. The advances in technology and analytical tools allowed the application of more comprehensive characterization packages for products such as adsorbed combination vaccines, which contain several antigens in a single formulation to protect against more than one disease, and may contain adjuvants and excipients. Aluminum phosphate (AlPO4) is a well-established adjuvant for enhancing the uptake of vaccines and to induce robust immunity against pathogens. During manufacturing, adjuvant is mixed with protein antigens which may in turn impact their higher order structure and stability. 2) Methods: To study the structural changes of protein antigens after adsorption several analytical tools including DLS, FTIR, Fluorescence, LD, and SEM were used. 3) Results: the AlPO4 adjuvant suspension consists of small submicron particles that form a continuous porous surface. Secondary structure alpha-helix and beta-sheet content of DT and TT increased after adsorption to AlPO4 adjuvant, whereas no significant changes were noted for other protein antigens. Interactions were noted between AlPO4 adjuvant and DT, TT, and FHA. 4) Conclusions: here we report for the first time the use of SEM for the visualization of adsorbed multivalent vaccine components. A unique signature profile detected for each multivalent vaccine by FTIR can be used as a lean in-process test to verify vaccine product composition and identity prior to filling.

The surface chemistry and the morphology of SnO2 nanowires, deposited by Vapour Phase Deposition (VPD) method on Au-covered silicon substrate, were studied before and after subsequent air exposure. For this purpose, surface-sensitive methods including X-ray Photoelectron Spectroscopy (XPS), Thermal Desorption Spectroscopy (TDS) and the Scanning Electron Microscopy (SEM) were applied. The studies presented within this paper allowed to determine the surface non-stoichiometry combined with the presence of carbon contaminations, in a good correlation with the surface morphology. The relative concentrations of the main components [O]/[Sn]; [C]/[Sn]; [Au]/[Sn] together with the O – Sn; O – Si bondings were analyzed. The results of TDS remained in a good agreement with the observations from XPS. Moreover, conclusions obtained for SnO2 nanostructures deposited with the use of Au catalyst were compared to the previous obtained for Ag-assisted tin dioxide nanowires. The information obtained within this studies are of great importance for the potential application of SnO2 nanowires deposited on Au covered Si substrate in the field of novel chemical nanosensor devices, since the results can provide an interpretation of how aging effects influence gas sensor dynamic characteristics.

This study compares the physico-chemical characteristics of three different types of biochar produced from biomass residues in Vietnam as a basis for optimising their application in water purification and soil fertilisation. Wood biochar (WBC), rice husk biochar (RBC), and bamboo biochar (BBC) were produced under limited oxygen conditions using equipment available locally in Vietnam, known as a Top-Lid Updraft Drum (TLUD). The resulting biochars were characterised using a suite of state-of-the-art methods to understand their morphology, surface chemistry and cation exchange capacity. Surface areas (measured by BET) for WBC and BBC were 479.34 m²/g and 434.53 m²/g, respectively, significantly higher than that of RBC which was only 3.29 m²/g. The morphology as shown in SEM images corresponds with the BET surface area, showing a smooth surface for RBC, a hollow surface for BBC, and a rough surface for WBC. All three biochars produced alkaline, with pH values around 10, and all have high carbon contents (47.95 - 82.1 %). Cation exchange capacity (CEC) was significantly different (p<0.05) among the biochars, being 26.70 cmol/kg for RBC, 20.7 cmol/kg for BBC, and 13.53 cmol/kg for WBC, which relates to the cations (Ca, Mg, K) and functional groups with negative charge (carboxyl, hydroxyl) present on the biochar surfaces. The highest contents of Ca, Mg and K in rice husk BC may explain its highest CEC values. Thus, although the biochars were produced by the same method, the various feedstocks lead to quite different physico-chemical properties. Ongoing work is linking these physico-chemical properties to the biochar efficiencies in terms of nitrate and ammonia capture capacities for use as fertilisers, and for adsorption of heavy metals (Zn, Cu) or water filtration, in order to design optimal biochar properties for specific applications.

Mitochondrial dysfunction and oxidative stress are thought to be relevant to the pathogenesis of age-related macular degeneration (AMD). Glutathione (GSH) homeostasis fulfills a number of important roles in mitochondria, such as maintenance of mitochondrial DNA and respiratory competency of cells. Although the transport of mitochondrial GSH (mGSH) is not fully understood, increasing evidence from non-ocular tissues suggests that OGC (2-oxoglutarate carrier, SLC25A11) and DIC (dicarboxylate carrier, SLC25A10) are involved in mGSH transport. However, whether OGC and DIC mediate the transfer of GSH into the mitochondria of retinal pigment epithelial cells (RPE) remains unknown. Thus, we investigated the expression, localization, and function of OGC and DIC in human RPE (hRPE) in relation to oxidative stress and GSH. Both OGC and DIC are expressed in hRPE and are localized in mitochondria. We also found a dose and time-dependent decrease of OGC and DIC expression under oxidative stress and increased expression in polarized RPE. Our data show that the downregulation of OGC and DIC resulted in increased apoptosis and mGSH depletion which can be overcome by co-treatment with GSH-MEE. These findings suggest that overexpression of OGC and DIC may be an effective strategy to decrease susceptibility to mitochondrial toxicants by elevation of mGSH.

The distribution of noble metal nanoparticles in hydrogels are influencing their nanoplasmonic response and signal used for biosensor purposes. By controlling the particle distribution, it is possible to obtain new nanoplasmonic features with new sensing modalities. Particle distributions can be characterized by using volume-imaging methods such as the focused ion beam-scanning electron microscope (FIB-SEM) and the serial block-face scanning electron microscopy (SBFSEM) techniques . Since the pore structure of hydrogels is contained by the water absorbed in the polymer network it may pose challenges for volume-imaging based on electron microscope techniques since the sample must be in a vacuum chamber. The structure of hydrogels can be conserved by choosing appropriate preparation methods, which also depends on the composition of the hydrogel used. In this paper, we have prepared low-weight percentage hydrogels, with and without gold nanorods (GNR) for conventional SEM imaging by using two different drying techniques; (1) the critical point drying (CPD) technique and (2) hexamethyldisilazane (HMDS) drying of hydrogels. A qualitative characterization of the GNR-hydrogels was carried out to study the GNRs positioned in the polymer network. The effect of the two different drying methods on the hydrogel morphology were also compared. The use of HMDS as an alternative to the CPD has several advantages involving less parametrical variables for drying, involving less effort, being cost-effective, and requires no equipment use. In addition, choosing an optimized sample preparation method for SEM with optimized imaging parameters is highly important for obtaining accurate information about materials that is not correlated to artifacts. Hence, the results obtained from the preparation methods and SEM imaging parameters in this paper are useful for developing methods for mapping the metal particle distributions in micro-hydrogels by using FIB-SEM and SBFSEM techniques.

There has been widespread criticism about the rates of participation of students enrolled on MOOCs (Massive Open Online Courses), more importantly, the percentage of students who actively consume course materials from beginning to the end. This study sought to investigate this trend by examining the factors that influence MOOC adoption and use by students in selected Ghanaian universities. The Unified Theory of Acceptance and Use of Technology (UTAUT) was extended to develop a research model. A survey was conducted with 270 questionnaires administered to students who had been assigned MOOCs; 204 questionnaires were retrieved for analysis. Findings of the study show that MOOC usage intention is influenced by computer self-efficacy, performance expectancy, and system quality. Results also showed that MOOC usage is influenced by facilitating conditions, instructional quality, and MOOC usage intention. Social influence and effort expectancy were found not to have a significant influence on MOOC usage intention. The authors conclude that universities must have structures and resources in place to promote the use of MOOCs by students. Computer skills training should also be part of the educational curriculum at all levels. MOOC designers must ensure good instructional quality by using the right pedagogical approaches and also ensure that the sites and learning materials are of good quality.

Recently, the awareness of energy conservation, carbon emission reduction, and environmental protection in Taiwan has begun to gradually improve, and bicycles have become an important vehicle for residents. In 2009, Kaohsiung began promoting public bicycle sharing. The number of users in that year amounted to 140,000. By 2015, the accumulated number of users reached nine million. This study adopted the Theory of Planned Behavior (TPB) to explore the factors influencing the behavioral intentions of public bicycle users, including the three dimensions of attitude, subjective norm, and perceived behavioral control, and probed into the relationship between the factors influencing the behavioral intentions of public bicycle users in Kaohsiung City and the dimensions. This study used a questionnaire to collect data and SPSS & AMOS for statistical analysis. The empirical results demonstrated that the most prominent factors influencing the behavioral intentions of public bicycle users in Kaohsiung City included perceived behavioral control, attitude, and subjective norm, in order. Among the influencing factors in the three dimensions, personal interests, main groups, and self-competence had a positive and significant correlation. Administrators should provide more incentives related to the three influencing factors to encourage the public in Kaohsiung City to use public bicycles more frequently as their short-distance travel mode, so as to achieve the purposes of saving energy, reducing carbon emissions, and protecting the urban environment.

In this investigation dyeing of alginate fiber was carried out after cationic treatment of EPTAC (2, 3-Epoxypropyl Trimethyl Ammonium Chloride). Optimum dyeing process and parameter show good dyeing performance when alginate fiber dyed with rhubarb dye. In addition to cationic treatment is taken into account for alginate fiber to improve fastness, color strength, breaking strength. Later in dyeing for fixation ferrous sulfate, copper sulphate was considered as mordents. Moreover using pre-mordanting methods conveyed the dyeing of alginate fiber with the stave of metallic mordant and without metallic salt mordents. The evaluation of each color dyed material was done through following two terms for instance CIELAB (L*, a*, and b*) and K/S values. According to AATCC test methods color fastness to washing of the dyed fiber was determined whereas according to the ASTM D3822M standard the breaking strength of alginate fiber was estimated and tested. When dyeing was carried out on alginate fiber through considering optimum parameter like 80◦C for 90 min, M: L 1:40 and at pH 7 which showed optimum results. In addition to mostly very good wash fastness was obtained while there was no fading of the color, whereas the moderate level of color fastness to crocking was achieved. Later after dyeing the evaluations of SEM of the cationized alginate fiber and FTIR of powder from the rhubarb dye were observed. The results suggested that the surface of cationized alginate fiber was smoother than the raw alginate fiber.

Background: in this paper, a new physical penetration technology for transdermal administration with traditional Chinese medicine (TCM) characteristics - Fu’s cupping therapy (FCT) - was established and studied by in-vitro and in-vivo experiments; the penetration effect and mechanism of FCT physical penetration technology (FCT-PPT) was preliminarily discussed. Method: Indomethacin (IM) as a model drug，by transdermal in vitro tests the establishment of the high，medium and low reference were finished as the chemical permeation system；chemical penetration enhancers and iontophoresis as a reference，the percutaneous penetration effect of FCT for IM patch was evaluated with 7 species diffusion kinetics model and in vitro drug distribution；naproxen as an internal standard，using UPLC-MS/MS technology，the IM quantitative analysis method in vivo was established，and pharmacokinetic parameters (AUC0-t，AUC0-∞，AUMC0-t，AUMC0-∞, Cmax and MRT) as indicators were used evaluate to FCT penetration role in vivo；in the same time，the group used 3K factorial design to study joint synergistic penetration effect on FCT and chemical penetration enhancers (CPEs)；by SEM and TEM，the skin micro and ultrastructural changes of the stratum corneum (SC) surface were observed, to explore pay tank penetration mechanism. Results: In vitro and in-vivo skin permeation experiments revealed that both the total cumulative percutaneous amount and in-vivo percutaneous absorption amount (AUC and AUMC) of indomethacin that permeated SD mouse skin using FCT techniques were greater than the amount observed using CPE and iontophoresis: Firstly, in contrast to the control group, the indomethacin percutaneous rate (PR) of the FCT lower group (FCTL) was 35.52%, and the enhancement ratio (ER) at 9h was 1.76X, which was roughly equivalent to the penetration enhancing effect of the CPEs and iontophoresis; secondly, the indomethacin PR of the FCT middle (FCTM) group and the FCT high intensity group (FCTH) were respectively 47.36% and 54.58%, ER at 9h were separately 3.58X and 8.39X; thirdly, pharmacokinetic studies showed that in-vivo indomethacin percutaneous absorption of the FCTs was higher than that of the control group, that of the FCTM group was slightly higher than that of the CPEs group, and that of the FCTM group was significantly higher than that of the others. Meanwhile, the variance analysis indicated that the combination of the FCT penetration enhancement method and the CPE method had beneficial effects in penetration enhancing of the skin: the significance level of the CPE method was 0.0004, which was apparently lower than the 0.001, meaning the difference was markedly significant; the significance level of the FCT was under 0.0001, its difference markedly significant; and the significance level of factor interaction A×B was lower than 0.0001, indicating that its difference of the synergism was markedly significant. Moreover, SEM and TEM images showed that the SC surfaces of SD rats treaded with FCT-PPT was damaged, and hard to observe the complete surface structure with its SC pores growing bigger and its special “brick structure” becoming looser, indicating that it broke the barrier function of skin, which revealed potentially a major route of skin penetration. Conclusion: FCT, as percutaneous penetration new technologies, has penetration effects significantly, with Chinese characteristics and highly clinical value, worth promoting development.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.