The electrical performance of the back-channel etched Indium–Gallium–Zinc–Oxide (IGZO) thin-film transistors (TFTs) with copper (Cu) source and drain (S/D) which are patterned by a selective etchant was investigated. The Cu S/D were fabricated on molybdenum (Mo) layer to prevent the Cu diffusion to the active layer (IGZO). We deposited the Cu layer using thermal evaporation and performed the selective wet etching of Cu using non-acidic special etchant without damaging the IGZO active layer. We fabricated the IGZO TFTs and compare the performance in terms of linear and saturation region mobility, threshold voltage and ON current (ION). The IGZO TFTs with Mo/Cu S/D exhibits good electrical properties as the linear region mobility is 12.3 cm2/V-s, saturation region mobility is 11 cm2/V-s, threshold voltage is 1.2 V and ION is 3.16 x 10-6 A. We patterned all the layers by photolithography process. Finally, we introduced SiO2-ESL layer to protect the device from the external influence. The results show that the prevention of Cu and introduced ESL layer enhances the electrical properties of IGZO TFTs.

In this paper, the design of a low cost portable ventilator with performance analysis have been done to solve the scarcity of respiratory ventilators for COVID-19 patients. The materials used to build the system are: DC motor, rotating disc and pneumatic piston. The system input is the patient heart beat and the output is volume of air to the patient lung with adjusted breathing rate. This ventilator adjusts the breathing rate to the patient depending on his heart beat rate. The performance analysis of this system have been done using Proportional Integral Derivative (PID) and Full State Feedback H2 controllers. Comparison of the system with the proposed controllers have been done using a step change and a random change of the patient heart beat and a promising result have been analyzed successfully.

DNA methylation is one of the epigenetic mechanisms which have been implicated in cellular differentiation, ageing and disease development. The effect of hypomethylating drug 5-aza-2´deoxycytidine (5-aza dC) on the biosynthetic profile of caudal region chondrocytes from chick sternum was studied in detail. The chondrocytes in culture were treated with varying doses of 5-aza dC for 48h and maintained subsequently without the treatment and harvested at selected time points for analysis of growth and differentiation status. 15µg/ml of 5-aza dC showed optimum Concentration at which there was a significant increase in DNA synthesis and RNA synthesis as per cell basis. There was also a significant increase in total protein synthesis and collagen synthesis as per cell basis at this concentration. This optimal concentration also showed to up regulate the gene expression of Type X collagen and alkaline phosphatase, which are the marker of hypertrophic chondrocyte expression. These results further support the notion that methylation is the major epigenetic factor controlling the differentiation and maturation of chondrocytes.

In this paper we investigate the optimal investment strategy for a defined contribution (DC) pension plan during the decumulation phrase which is risk-averse and pays close attention to inflation risk. The plan aims to maximize the expected constant relative risk aversion (CRRA) utility from the terminal wealth by investing the wealth in a financial market consisting of an inflation-indexed bond, an ordinary zero coupon bond and a risk-free asset. We derive the optimal investment strategy in closed-form using the dynamic programming approach by solving the corresponding Hamilton-Jacobi-Bellman (HJB) equation. Our theoretical and numerical results reveal that under some rational assumptions, an inflation-indexed bond do has significant advantage to hedge inflation risk.

The study explores antibacterial, antiinflammatory and cytoprotective capacity of Pelargonium sidoides DC root extract (PSRE) and proanthocyanidin fraction from PSRE (PACN) under conditions characteristic for periodontal disease. Following previous finding that PACN exerts stronger suppression of Porphyromonas gingivalis compared to the effect on commensal Streptococcus salivarius, the current work continues antibacterial investigation on Staphylococcus aureus, Staphylococcus epidermidis, Aggregatibacter actinomycetemcomitans and Escherichia coli. PSRE and PACN are also studied for their ability to prevent gingival fibroblast cell death in the presence of bacteria or bacterial lipopolysaccharide (LPS), to block LPS- or LPS+IFNγ-induced release of inflammatory mediators, gene expression and surface antigen presentation. Both PSRE and PACN were more efficient in suppressing Staphylococcus and Aggregatibacter compared to Escherichia, prevented A. actinomycetemcomitans- and LPS induced death of fibroblasts, decreased LPS-induced release of interleukin 8 and prostaglandin E2 from fibroblasts and IL-6 from leukocytes, blocked expression of IL-1β, iNOS, and surface presentation of CD80 and CD86 in LPS+IFNγ-treated macrophages, and IL-1β and COX-2 expression in LPS-treated leukocytes. None of the investigated substances affected either the level of secretion or expression of TNFα. In conclusion, PSRE, and especially PACN, possess strong antibacterial, antiinflammatory and gingival tissue protecting properties under periodontitis mimicking conditions and are suggestable candidates for treatment of the disease.

During HVDC earth return operation systems, a high magnitude current will be injected into soil through earth electrode, the potential on the surface would change widely and produce unfavorable effects on the AC systems around. This paper presents an effective finite element method (FEM) coupling electric field with thermal field to evaluate the electrical field induced by the injected DC current. Firstly, owe to the characteristic of FEM, this method can consider arbitrary soil and earth electrode structure. Secondly, by setting the electrical and thermal parameters of soil as a function of temperature at the same time, the dynamic coupling process of electric field and thermal field is simulated accurately. Thirdly, to deal with the singular point in FEM subdivision and the huge computation in traditional three-dimensional FEM, the FEM coupling 2-D earth electrode with 3-D soil based on "shell" theory is introduced. Finally, based on the suggested method, the effect of abnormal resistance region (ARR) near DC earth electrode on electric field distribution is analyzed.

In the era of electrification and artificial intelligence, direct current motors are widely utilized with numerous innovative adaptive and learning methods. Traditional methods utilize model-based algebraic techniques with system identification, such as recursive least squares, extended least squares, and autoregressive moving averages. The new method known as deterministic artificial intelligence asserts physical-based process dynamics to achieve target trajectory tracking. There are two common autonomous trajectory generation algorithms: sinusoidal function and Pontryagin's based generation algorithm. This thesis aims to simulate model-following and deterministic artificial intelligence methods using sinusoidal and Pontryagin's methods and compare their performance difference when following challenging step function slew maneuver.

Discretization is the process of converting a continuous function or model or equation into discrete steps. In this work, adaptive and learning methods are implemented to control DC motors that are used for actuating control surfaces of unmanned underwater vehicles. Adaptive control is a method in which the controller is designed to adapt the system with parameters which vary or are uncertain. Parameter estimation is the process of computing the parameters of a system using a model & measured data. Adaptive methods have been used in conjunction with different parameter estimation techniques. Deterministic artificial intelligence, a learning-based approach that uses the process dynamics defined by physics, is also applied to control the output of the DC motor to track a specified trajectory. This work goes further to evaluate the performance of the adaptive & learning techniques based on different discretization methods. The results are evaluated based on the absolute error mean between the output & the reference trajectory and the standard deviation of the error. The first order-hold method of discretization and surprisingly large sample time of seven tenths of a second yields over sixty percent improvement over the results presented in the prequel literature.

The work addresses the problem of Power Quality (PQ) metrics (or indexes) suitable for DC grids, encompassing Low and Medium Voltage applications, including electric transports, all-electric ships and aircrafts, electric vehicles, distributed generation and microgrids, modern data centers, etc. The two main pillars on which such PQ indexes are discussed and built are: i) the physical justification, so the electric phenomena affecting DC grids and components (PV panels, fuel cells, capacitors, batteries, etc.), causing e.g. stress of materials, ageing, distortion, grid instability; ii) the existing standardization framework, pointing out desirable coverage and extension, similarity with AC grids standards, but also inconsistencies. The first point is made more clear and usable by a graphical overview of the discussed phenomena. On this basis PQ is interpreted beyond the usual low-frequency range, including thus supraharmonics and common-mode disturbance, and filling the gap with the Electromagnetic Compatibility domain. However, phenomena typical of EMC and electrical safety (such as various types of overvoltages and fast transients) are excluded. Suitable PQ indexes are then reviewed, suggesting integrations and modifications, to cover the relevant phenomena and technological progress, and to better follow the normative exigencies.

Wireless power transfer promises to revolutionize the way we use and power mobile devices. However, low transfer efficiencies prevent this technology from seeing wide scale real-world adoption. The aim of this work is to use quasioptics to develop a system composed of a dielectric lens fed by a phased array to reduce spillover losses, increasing the beam efficiency, while working on the antenna system’s Fresnel zone. The DC-RF electronics, digital beamforming and beam-steering by an FPGA, and radiating 4x4 microstrip patch phased array have been developed and experimented upon, while the lens has been designed and simulated. This paper details these preliminary results, where the phased array radiation pattern was measured, showing that the beam is being generated and steered as expected, prompting the lens construction for the complete system experimentation.

The current spreading novel coronavirus SARS-CoV-2 is highly infectious and pathogenic and has attracted global attention. Recent studies have found that SARS-CoV-2 and SARS-CoV share around 80% of homology and use the same cell entry receptor, ACE2. These inspired us to study other receptors of SARS-CoV, which may be used for SARS-CoV-2 binding as well. In this study, we screened the gene expression of three receptors (ACE2, DC-SIGN and L-SIGN) in four datasets of normal lung tissue from lung adenocarcinoma patients and two single-cell RNA sequencing datasets from normal lung and bronchial epithelial cells separately. No significant difference in gene expression of these three receptors were found between gender groups (male vs female). We found higher gene expression of DC-SIGN in elder with age>60 and higher gene expression of L-SIGN in Caucasian than Asian. Similar to ACE2, we observed significantly higher DC-SIGN gene expression in the lungs of smokers, especially former smokers. However, smokers upregulate ACE2 and DC-SIGN gene expression in different cell types. In the whole lung, ACE2 is actively expressed in remodeled Alveolar Type II cells of former smokers, while DC-SIGN is largely expressed in monocytes of former smokers and dendritic cells of current smokers. In bronchial epithelium, no obvious gene expression of DC-SIGN and L-SIGN was observed while ACE2 was found to be actively expressed in goblet cells of current smokers and club cells of non-smokers. In conclusion, our findings may indicate that smokers, especially former smokers, and people over 60 have higher risk and are more susceptible to SARS-CoV-2 infection. Also, this study provides hints on possible SARS-CoV-2 pathogenicity mechanisms in lung infection.

The article introduces a new solution approach to grid-connected single-stage three-phase PV inverter whereby a dc-link voltage can successfully achieve the desired performance. As a single-stage, the variable output of perturb and observe maximum power point tracking (P&O based-MPPT) is fully utilized as dc-link voltage reference in inverter control scheme. As a result, it is challenging for the dc-link voltage to preserve energy balance by tracking its variable dc-link voltage reference under unpredictable environmental changes. To overcome this challenge, an adaptive reference proportional-integral (ARPI) controller, self-tuning, is designed and implemented to compel the dc-link voltage tracking its voltage reference to be equal as closely as possible; hence, the capability of the dc-link under abnormal events substantially guarantees the best energy balance and transient performance enhancement. To verify the validity of the method, simulation results for multiple events scenarios on 250 KW single-stage grid-connected PV systems show the effectiveness of the ARPI controller compared with PI controller.

In this research paper, a hybrid Artificial Neural Network (ANN)-Fuzzy Logic Control (FLC) tuned Flower Pollination Algorithm (FPA) as a Maximum Power Point Tracker (MPPT) is employed to emend root mean square error (RMSE) of photovoltaic (PV) modeling. Moreover, Gaussian membership functions have been considered for fuzzy controller design. This paper interprets Luo converter occupied brushless DC motor (BLDC) directed PV water pump application. Experimental responses certify the effectiveness of the suggested motor-pump system supporting diverse operating states. Luo converter is newly developed dc-dc converter has high power density, better voltage gain transfer and superior output waveform and able to track optimal power from PV modules. For BLDC speed controlling there is no extra circuitry and phase current sensors are enforced for this scheme. The recentness of this attempt is adaptive neuro-fuzzy inference system (ANFIS)-FPA operated BLDC directed PV pump with advanced Luo converter has not been formerly conferred.

A novel metaheuristic optimization method is proposed based on an earthquake that is a geology phenomenon. The novel Earthquake Algorithm (EA) proposed, adapts the principle of propagation of geology waves P and S through the earth material composed by random density to ensure the dynamic balance between exploration and exploitation, in order to reach the best solution to optimization complex problems by searching for the optimum into the search space. The performance and validation of the EA are compared against the Bat Algorithm (BA) and the Particle Swarm Optimization (PSO) by using 10 diverse benchmark functions. In addition, an experimental engineering application is implemented to evaluate the proposed algorithm. Early results show a feasibility of the proposed method with a clearly constancy and stability. It is important highlight the fact that the main purpose of this paper is to present a new line of research, which is opened from the novel EA.

The medium-voltage DC (MVDC) technology has gained increasing interests in recent years. Power electronics devices dominate those grids. Accurate simulation of such a grid, with detailed models of switching semiconductors, can quickly became very time-consuming, according to the number of connected devices to be simulated. A simulation approach based on interactions on a continuous time model can be very interesting, especially for developing a system level control model of such a modern MVDC distribution grid. Aim of this paper is to present all the steps required for obtaining a continuous time modelling of a +/- 10 kV MVDC grid case study, including Solid State Transformer (SST) and Modular Multilevel Converter (MMC) based Active Front End (AFE). Additional aim of this paper is to supply an educational content about the use of the continuous time simulation approach, thanks to a detailed description of the various devices modelled into the presented MVDC grid. The results of a certain number of simulation scenarios are eventually presented.

In many developing countries of the world including Pakistan motorcycle steeling is one of the main issue that needs to be dealt with an iron hand as it leads to economic losses as well as crime increase in the society, according to the DOWN REPORT there were 28609 motorcycle stolen in 2019 and this number has been increased to 34908 in 2020. Now due to the increasing motorcycles stealing crime what measures can we take to reduce the number of motorcycle theft the rule of technology is enormous in this regards specially information technology (IT) , information technology can play an important role in the security of motorcycles from being theft by the thieves, Information technology provide us the GSM based control system which can be very help full to construct a security system for motorcycle in order to make it antitheft.

This contribution considers an improved control scheme for three-phase two-stage grid-tied photovoltaic (PV) power system based on integral sliding mode control (ISMC) theory. The proposed control scheme consists of maximum power point tracking (MPPT), DC-Link voltage regulation and grid currents synchronization. A modified voltage-oriented maximum power point tracking (VO-MPPT) method based on ISMC theory is proposed for design of an enhanced MPPT under irradiation changes. Moreover, a novel DC-Link voltage control based on ISMC theory is proposed in order to achieve good regulation of DC-Link voltage over its reference. To inject the generated PV power into the grid with high quality, a voltage oriented control based on space vector modulation (SVM) and ISMC (VOC-ISMC-SVM) has been developed to control the grid currents synchronization. Numerical simulations are performed in Matlab/SimulinkTM environment in order to evaluate the proposed control strategy. In comparison with conventional control scheme, the developed control strategy provides an accurate MPP tracking with less power oscillation as well as a fast and an accurate DC-Link regulation under climatic conditions variations. Moreover, the transfer of the extracted power into the grid is achieved with high quality.

This research paper focuses on the synthesis and characterization of Cu-doped Mg-Co ferrites with varying compositions (Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3) using a solid-state reaction method. This paper also investigates the structural, morphological, magnetic, and electrical characteristics of synthesized Mg_0.6-xCo_0.4Cu_xFe₂O₄, where x = 0.0, 0.1, 0.2, and 0.3. The X-ray diffraction (XRD) technique confirms the ferrites spinel structure in the Fd-3m space group, with average crystallite sizes ranging from 57.29 to 48.57 nm. Fourier Transform Infrared (FTIR) spectroscopy verifies chemical and structural changes, while scanning electron microscopy (SEM) reveals cubic crystal growth with an average grain size of 1 to 1.5 μm. DC electrical resistivity decreases with increasing temperature and Cu²⁺ substitution, ranging from 1.4 x 10⁶ Ω-cm to 6.7 x 10⁵ Ω-cm. The study suggests a correlation between resistivity and Cu²⁺ concentration. Magnetic behaviour, studied using a Vibrating Sample Magnetometer (VSM), shows dependence on dopant concentration, with coercivity ranging from 157 Oe to 256 Oe. The results indicate potential applications in magnetic storage devices, antennas, transformers, and high-frequency electronics.

Surface-enhanced Raman spectroscopy (SERS) is commonly used for super-selective analysis through nanostructured silver layers in the environment, food quality, biomedicine, and materials science. To fabricate a high-sensitivity but more accessible device of SERS, dc magnetron sputtering technology was used to realize high sensitivity, low cost, stable deposition rate, and rapid mass production. This study investigated various thicknesses of a silver film ranging from 3.0 to 12.1 nm by field-emission-scanning-electron microscope, X-ray diffraction, and X-ray photoelectron spectroscopy. In the rhodamine 6G (R6G) testing irradiated by a He-Ne laser beam, the analytical enhancement factor (AEF) of 9.35x108, the limit of detection (LOD) of 10-8 M, and the relative standard deviation (RSD) of 1.61% were better than other SERS substrates fabricated by the same dc sputtering process because the results show that the 6 nm thickness silver layer has the highest sensitivity, stability, and lifetime. The paraquat and acetylcholine analytes were further investigated and high sensitivity was also achievable. The proposed SERS samples were evaluated and stored in a low humidity environment for up to forty weeks, and no spectrum attenuation could be detected. Soon, the proposed technology to fabricate high sensitivity, repeatability, and robust SERS substrate will be an optimized process technology in multiple applications.