Emissions from wood burning for heating in secondary homes or cabins is an important aspect for the development of high-resolution emission inventories in specific areas. Norway is used as case study as the national wood consumption for heating in cabins is around 20% of the total. Our study shows first a method to estimate emissions from cabins based on traffic data to derive cabin occupancy, which combined with heating need allows for the spatial and temporal distribution of emissions. The combination of residential (RWC) and cabin wood combustion (CWC) emissions shows large spatial and temporal differences, and a temporally “cabin population” can in areas be orders of magnitude larger than the registered population. While RWC emissions have been steadily reduced, CWC have kept relatively constant or even increased, which results on an increase in the cabin share to total heating emissions up to 25-35%. When comparing with regional emissions inventories, our study shows that the gradient between rural and urban areas is not well represented in regional emissions inventories, which resembles a population-based distribution and does not allocate emissions in cabin municipalities. At last, our study shows that CWC emissions may become an increasing environmental concern as higher densification trends in mountain areas are observed.

Batch combustion in wood log stoves is a promising application for latent heat storage (LHS), due to the transient heat production with high peak effects. The current study aimed at designing a compact, passive and durable LHS system storing a substantial part of the heat release during batch combustion and effectively releasing the stored heat to the room for 6 to 10 hours after the last batch. The LHS system consists of a coaxial cylinder located at the top of the wood stove, replacing part of the regular stovepipe. Internal metallic fins were applied as heat transfer enhancement to homogenize the temperature distribution inside the PCM. The effect of radial fin lengths was numerically investigated through a parametric study using five different fin lengths within the PCM. Using 35-mm fins in the 70-mm PCM layer yielded the best trade-off for the application. This configuration enabled achieving a slow but close to complete melting of the PCM within a realistic combustion duration, while avoiding overheating the PCM above its degradation temperature. Thereafter, the discharge allowed releasing the stored latent heat for 6 hours. The exhaust gas inlet temperature proved to have a strong influence on the PCM thermal performance.

Natural dyes offer a bio-based opportunity to support attractive coloration to textile fabrics made from natural fibers like cotton, wool, hemp and many other materials. They can be part of a strategy to realize fully bio-based textile materials and clothing. Following this statement, the actual study investigates the use of wood extracts for dyeing of cotton fabrics. Actually extract powders of Logwood (Haematoxylon campechianum L.), Brazilwood (Caesalpinia spp.), and Quebracho wood (Schinopsis lorentzii) are used. The dyeing process is modified using different mordants based on iron and aluminum salts. These mordants are applied in pre-, meta- or post-mordant procedures. Color and fastness properties of prepared textile samples are determined by spectroscopic measurements, color measurements, washing procedures and Xenotest for measuring the light fastness. Finally, a broad range of different colorations can be realized by different combinations of wood extracts and mordanting procedures. A good wash fastness is reached for some color shades. For reaching good wash fastness, pre- and meta-mordanting procedures are more advantageous compared to post-mordanting. However, the light fastness of realized samples is only moderate to low. In conclusion, it can be stated that dyes from wood extracts are excellent materials to dye natural fibers if they are combined with the right mordanting agent in pre- or meta-mordanting procedures. The actual study is therefore a good proof-of-concept for the realization of fully bio-based colored textile materials.

Main pathogens affecting carob (Ceratonia siliqua) tree in the Mediterranean basin are described in this overview. The most widespread diseases periodically occurring on carob orchards are powdery mildew (Pseudoidium ceratoniae) and cercospora leaf spot (Pseudocercospora ceratoniae). The causal agents of so-called “black leaf spots” (e.g. Pestaliotiopsis, Phyllosticta and Septoria spp.) are responsible for similar symptoms to above mentioned foliar diseases but are reported on carob orchards with a negligible frequency. Likewise, canker and branch diebacks caused by fungal species belonging to Botryosphaeriaceae are almost never recorded. Among wood diseases that may compromise old or previously damaged carob specimens, “brown cubical heart rot” caused by Laetiporus sulphureus is the most widespread and recurrent issue; this pathogen is also well-known for edible fruit bodies that are also appreciated for pharmaceutical and industrial purposes. On the other hand, “white decays” caused by Fomes and Ganoderma species are less common and reported for the first time in this review. Like-gall protuberances on twigs at uncertain aetiology or tumours on branches associated to Rhyzobium radiobacter are described although these symptoms are seldom detected as it happens also for necrotic leaf spots caused by Pseudomonas syringae pv. ciccaronei. A list of worldwide pathogens not yet recorded but at high-risk potential of introduction in Italian carob producing area is also provided. Finally, some concerns are addressed to new phytopathogenic fungi vectored by invasive Xylosandrus compactus ambrosia beetle. Comprehensively, all described pathogens could potentially in near future become limiting factors for carob production, because they could be favoured by high-density orchards, increasing global network of trade exchanges and high frequency through which extreme events of climate changes globally occur. Thus, symptoms and signs, causal agents, epidemiology and whenever applicable recommendations for disease prevention and management are provided in this review.

Uganda possesses natural rainforests that serve enormous environmental ecosystems and biodiversity services. Moreover, the country is known for its various tropical rainforest hardwoods, birds, and animal species. Over the years, the trend in the natural forest land has declined at an alarming rate; hence need to investigate the possible drivers. The loss of such biodiversity and ecosystems risks desertification and extreme climatic condition. As the world moves towards Zero Deforestation 2030, understanding the determinants of deforestation and forest degradation is paramount. Therefore, the main objective of this study was to understand the impact and relationships between net forest conversion, energy emission, agriculture, and forest production of Roundwood. We used data from FAO for the period 2004-2016. Using the ADF and KPSS test, we checked for the unit root presence in the variables. Also, the study used two different regression models: multiple linear regression and dynamic linear model. To analyze the determinants of deforestation, we used net forest conversion in Uganda. There was 94 % variation in the dependent variable (Net Forest conversion). The outcome of the dynamic linear regression showed that agriculture and energy emission positively impact net forest conversion. Based on our findings, this study recommended the modernization of agriculture by the government of Uganda to stop cutting down the forests on a big scale. Also, the study suggested that the government strictly legislate Roundwood and wood fuels/charcoal and firewood to reduce huge dependency on forests toward Zero-Deforestation by 2030. If well-structured and implemented, government policies could solve the unnecessary over dependency on the rainforest, the heart of the region's climatic conditions.

The effectiveness of forest resources depends on the comprehensiveness and rationality of their consumption and processing into finished products. This article discusses a problem of utilising solid fir wood greenery residues generated during the industrial production of essential oils. Bioconversion is considered to be the most promising utilization method. The objective of this research was to study the chemical composition of bioconversion products of fir wood greenery-based substrates. The РР-3.2 strain of Pleurotus pulmonarius (Fr.) Quél was used as a biodestructor. In the process of bioconversion, the contents of polysaccharides and lignin substances is reduced to 38 and 28 % respectively. Up to 20 % of protein accumulates in bioconversion products of fir wood greenery. The amount of nucleic acids is not more than 1.5 g per 1 kg, the contents of heavy metals, such as mercury, cadmium, arsenic, lead, do not exceed maximum permissible concentration standards. The substrate weight loss reaches 15 %. When fallen leaves and post-extraction poplar bud residues are added to the substrate, the substrate-destroying activity of fungi rises, as well as the protein content increases by 3 %. The digestibility of products as a result of bioconversion increases 1.6–2.8 times depending on the substrate composition. The obtained data enable to recommend post-fermented substrates based on fir wood greenery and balsam poplar biomass for use as a protein feed additive.

Forestry and the wood-based sector, including the wood industry, which is an important element of economic systems and a source of budget revenues for many countries in the world, found itself in the first quarter of 2020 in a situation of a serious threat of a prolonged crisis as a consequence of the pandemic. In this perspective, it is necessary to review existing sector strategies and look for new solutions to ensure first survival, then functioning and finally development of entities forming the wood market. In the scientific research, which is the subject of this work, an attempt was made to multi-criteria analysis of the selection of the optimal anti-crisis strategy for actors from forestry and the wood-based sector in the face of a pandemic. Preparatory studies were conducted on the example of Poland, where both forestry and the wood industry belong to the dominant sectors of the economy, conducting them at the turn of March and April 2020. The research was referred to the primary wood raw material market in Poland, which is the main link in the value chain, created first by the dominant owner: Państwowe Gospodarstwo Leśne "Lasy Państwowe" - the “State Forests” National Forest Holding (SFNFH), and then forest service entrepreneurs, to entities representing the wood industry. The work uses a concept modified for the purposes of the author's research scenario, based on the method of multi-criteria hierarchical analysis AHP (Analytic Hierarchy Process). The best possible decision was to be searched that would allow the selection of the optimal anti-crisis strategy for enterprises - actors of the sector concerned. Based on the collected results and their expert discussion, recommendations for sectoral policy for forestry and the wood-based sector were then formulated. The proposed solutions are located against the background of a dispute between the concept of institutional intervention and a model taking into account the effects of market factors. The work is both cognitive (optimization and adaptation of the research method) and practical up-to-date. An accurate development strategy for forestry and the wood-based sector is urgently needed and necessary to implement as quickly as possible.

Ranaviruses have been associated with rising numbers of mass die-offs in amphibian populations globally. With life-stages occupying different environments and presenting distinct physiologies, amphibian of different ages are likely to play an important role in pathogen persistence. To assess the potential role of post-metamorphic amphibians as a Ranavirus reservoir, we performed a bath-exposure study on wood frogs using environmentally relevant doses (~10³ and ~10⁴ PFU/mL) of wild-type (WT) and knockout Frog virus 3 (FV3), deficient for the vIF-2α immune-evasion gene, the effects of which have never been addressed in post-metamorphic anurans. We observed 42% infection prevalence and low mortality (10%) across the virus challenges, with half of the mortalities attributable to ranavirosis. Prevalence and viral loads followed a dose-dependent pattern. Notably, when exposed to the vIF-2α knockout (DvIF-2α) FV3, individuals exhibited significantly decreased growth and increased lethargy in comparison to WT FV3 treatments. Although 85% of individuals in the virus treatments exhibited stereotypic signs of ranavirosis throughout the experiment, at termination (40 days post exposure) most individuals were clear of signs of infection. Overall, this study provides evidence that even a single short time exposure to environmentally relevant doses of Ranavirus may cause sublethal infections in post-metamorphic amphibians, thus indicating their possible role as a reservoir for this pathogen.

The prohibitive costs of small-scale solar photovoltaic (PV) racks decreases PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt mounted racking designs that allow manual change of tilt angle from zero to 90 degrees by varying the length of cables. The racks are designed using the calculated dead, wind and snow loads for Canada as conservative design for most of the rest of the world. Structural capacities of the wooden members are then ascertained and resisting bending moment, shear force, tensile force, and compressive force for them is calculated. A structural and truss analysis is performed to ensure that racking design with-stands the applicable forces. Moreover, implications of changing the tilt angle on the wooden members/cables used to build the system are also determined. The systems offer significant economic savings ranging from 1/3rd to 2/3rd the capital expenses of the commercially available alternatives. In addition, the racking designs are easy-to-build and require minimal manufacturing operations, which increases their accessibility. The stilt-mounted designs can be employed for agrivoltaic settings while allowing farm workers shaded ergonomic access to perform planting, weeding, and harvesting.

The pulp and paper industry is one of the biggest industry sectors worldwide, whose market growth is expected to reach 370.12 billion USD by 2028. However, as a water-intensive process, the pulp and paper production generate huge volumes of contaminated effluents, some of which contain dissolved high-value chemical compounds, such as lignin, hemicellulose, or carboxylic acids. These compounds can be recovered using membrane operations. Thus, membrane operations represent a method to valorize effluents and byproducts from this industry sector and narrow the gap between biorefinery models and the pulp and paper production as an integrated biorefinery. The present review reviews the state-of-the-art-research and the state-of-the-art applications of membrane operations in the pulp and paper industry.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

In the present work we have studied the short-term edaphic recovery of a burned pine forest of Pinus pinaster Aiton in Cerro del Castillo (Sierra de Guadarrama, Central Spain) in which a hydrological-forestry restoration was being carried out after the fire occurred in July 2022. For this purpose, variations in physicochemical properties (conductivity, relative humidity, organic matter and pH) and collembolan communities were analyzed by comparing the soils of a natural pine forest and a burned pine forest during the 24 weeks after the fire in 3 different samplings. With the data obtained, a series of diversity indices were calculated and statistical analyses such as ANOVA, hierarchical classification and principal component analysis were developed, with the aim of understanding in greater depth the recovery of collembolan populations, the changes in these physicochemical variables and the relationships between both parameters. This study shows how the fire reduced the amount of organic matter and water, and increased soil pH and conductivity, affecting edaphic fauna populations. In the short term, there was an increase in relative humidity and a decrease in electrical conductivity. The edaphic fauna communities of the burned pine forest increased their diversity and equity without reaching the values of the natural pine forest. At the specific level, however, the springtail populations matched the richness and even reached a very slightly higher Shanon-Wiener diversity index than that the natural pine forest populations in just 24 weeks. Finally, it was observed that the samples from the burned pine forest with recovered collembolan populations had the closest physicochemical parameters to those of the natural pine forest.

Although solar photovoltaic (PV) system costs have declined, capital cost remains a barrier to widespread adoption. Do-it-yourself (DIY) system designs can decrease costs by about 50% by reducing labor costs, but if not attached to a building structure demand ground penetration for conventional footings. This is not technically and economically feasible at all sites. To overcome these challenges, this study details systems designed to eliminate drilling holes and pouring concrete. Two different designs for both fixed tilt and variable tilt PV racking are investigated to assess their structural integrity, constructability, and economic cost when fabricated with a ballast-supported foundation. The ballast-supported foundations are analyzed for eight such systems by proposing two separate ballast designs: one for single line of post systems, and one for double line of post systems built on a 4-kW basis. The results of the analysis found that both designs are slightly more expensive than typical in-ground concrete systems by 25%, but the overall DIY systems costs remain economically advantageous. Sensitivity analyses are conducted to show how modifications to the dimensions including clearances and distances between gabions influence the weight of the system and thus change the economic value of the design, so users can trade dimensional freedom for cost-savings, and vice versa. Overall, all the wood-based PV racking system designs provide users with cost-effective and easy DIY alternatives to conventional metal racking, and the novel ballast systems presented provide more versatility for PV systems installations.

This study examines the impact of chainsaw chain type and tree species on the concen-tration of inhalable wood dust generated during motor-manual harvesting in forested areas. The chainsaw chain is a critical component, contributing not only to productivity but also to the oper-ator's health and safety. Wood dust creation during harvesting operations poses significant risks and necessitates careful attention due to its potential health effects. We investigated the effects by conducting real-world measurements of inhalable dust within the operator's breathing zone during forestry work. Two different chain types were evaluated: the commonly used 3/8" pitch chain (conventional chain) and the 0.325" pitch chain. Additionally, measurements were taken for three tree species: beech, oak, and pine (including both live and standing dead trees after a fire). Results showed that, overall, using the conventional 3/8" chain type yielded the highest concentration of wood dust for all three tree species. Notably, the highest wood dust concentration was observed in the burned Pinus brutia cluster, also with the 3/8" chain pitch. These findings emphasize the im-portance of understanding how chain type and tree species contribute to wood dust levels and provide valuable insights for enhancing operator health and safety during motor-manual har-vesting operations

The understanding of structural alteration mechanisms due to relative humidity impact on organic supports of paintings is of crucial significance for the preventive conservation strategies in order to ensure the long-term preservation of important cultural identity artworks. The effort in this paper is to simulate Museum realistic relative humidity condition in a climate chamber while monitoring the structural responses through a quantitative interferometric method allowing the quantitative correlation between the physical values of deformation and mass alteration relevant to relative humidity fluctuations.

Burning woody biomass for energy is gaining attention due to environmental issues associated with fossil fuels and carbon emission. The carbon released from burning wood is absorbed by plants and is carbon neutral. The purpose of this study was to investigate the combustion characteristics (heat calorific values and ash contents) of three timbers: Araucaria cunninghamii, Instia bijuga and Pometia pinnata and recommend for fuelwood. The test samples were sawdust particles (treatment) and solid woods (control) extracted from the heartwoods. The sawdust particles were oven-dried, sieved and pelletized into pellets using a hand-held pelletizing device, thus, forming cylindrical dimension (volume 1178.57 mm3, oven dry density 0.0008 g/mm3). While the solid woods were cubed and oven-dried (volume 1000.00 mm3, oven dry density 0.001 g/mm3). Prior to combustion in a semi-automatic bomb calorimeter, 90 test specimens (15 replicates per treatment and control per species) were conditioned to 14 % moisture content (at temperature 105 ºC) and weighed to a constant (unit) mass (1.0 g). The heat energy outputs and ash residues (of treatments) were analyzed statistically. The results indicated variability in heat energy outputs and ash residues between test specimens of the three species. Comparatively, the treatment specimens of A. cunninghamii produced higher calorific value (18.546 kJ/g) than the control (18.376 kJ/g) whilst the treatment specimens of I. bijuga and P. pinnata generated lower heat calorific values (17.124 kJ/g and 18.822 kJ/g) than the control (18.415 kJ/g and 20.659 kJ/g), respectively. According to ash content analysis, A. cunninghamii generated higher residues (6.3%) followed by P. pinnata (4.5%) and I. bijuga (2.8%). The treatment specimens of the three species could not meet the standard heat energy requirement (20.0 kJ/g) and thus, were unsuitable for fuelwood. However, the control specimens of P. pinnata generated equivalent heat energy (20.659 kJ/g) and could be a potential fuelwood.

The importance of the national security of supply has been emphasized in recent years due to the COVID-19 pandemic and changes in operating environments. Thanks to autonomy and resiliency in fuel procurement, organizations with decentralized energy plants may be able to quickly adapt to the changing needs of society. The main aim of this study was to increase the sustainability of a Finnish CHP plant's wood procurement by determining the company's profitable wood procurement region while keeping the forests renewable. The income received from the sale of energy and the costs incurred from the procurement of wood were collected from the ERP system as input data for the developed DSS. The environmental sustainability of wood procurement was assessed by considering the additional costs caused through the EEAP mechanism if the carbon sink of the forest worsened due to wood procurement in the area. The supply chains were compared so that the CHP plant managers could adopt the best energy wood value chains. The results showed that updating the procurement strategy would be necessary. The CHP plant managers should purchase energy wood from a larger procurement area than the current one and focus on roadside purchases of wood. The Techno-Economic Wood Payment Ability Model was a useful part of the DSS to guide wood buyers toward sustainable wood procurement by increasing the share of renewable forests.

The owners of forests with water protection functions in Bulgaria do not receive compensation for their limited right to use wood and non-wood forest products from the forest areas they own. At the same time, the contribution derived from forests with water protection functions is received by water users and water consumers, whereas the costs of managing the forests are borne by their owners. The problem thus defined is not a forestry one, but an economic one, and the purpose of this paper ensues therefrom, namely to propose and test a methodology for valuating the produc-tion function of forest areas with water protection function in Bulgaria, allowing a fair distribu-tion of income between the forest owner and the user of forest ecosystem services. The methodol-ogy is based on the form of forest management and the analytical expression of the economic rela-tionship between a forest owner and a user of forest ecosystem services, constructed using Schen-rock’s formula. It has been tested with actual data on forest areas with water protection functions falling within the administrative and territorial scope of Velingrad municipality and based on the obtained results proposals have been made for the distribution of the contributions generated by forest ecosystems between the forest owner and the user of the forest ecosystem services.

With heat treatments to control drywood termites (Blattodea: Kalotermitidae), the presence of heat sinks causes heat to be distributed unevenly throughout the treatment areas. Drywood termites may move to galleries in heat sink areas to avoid exposure to lethal temperatures. Our studies were conducted in Crytotermes brevis-infested condominiums in Honolulu, Hawaii to reflect real-world condominium scenarios; either a standard heat treatment performed by a heat remediation company or an improved heat treatment was used. For improved treatments, heated air was directed into the toe-kick voids of C. brevis infested cabinets to reduce heat sink effects and increase the heat penetration into these difficult-to-heat areas. Eight thermistor sensors placed inside toe-kick voids, treatment zone, embedded inside cabinets’ sidewalls, and in a wooden cube recorded target temperatures of above 46 °C or 50 °C for 120 minutes. A pretreatment and follow-up inspections were performed at 6 months posttreatment to monitor termite inactivity using visual observations and by recording the numbers of spiked peaks on a microwave technology termite detection device (Termatrac). In improved treatment condominiums, significantly higher numbers of spiked peaks were recorded at pretreatment as compared to 6 months posttreatment. Efficacious heat treatment protocols using the improved methods are proposed.

The amount and spatial distribution of foliage in a tree canopy have fundamental functions in ecosystems as they affect energy and mass fluxes through photosynthesis and transpiration. They are usually described by the Leaf Area Index (LAI) and the Leaf Area Density (LAD), which can be measured through a variety of methods, including voxel-based methods applied to LiDAR point clouds. A theoretical study recently compared the numerical errors arising from different voxel-based estimation methods for Plant Area Density (PAD) based on Beer’s law-based, contact frequency and Maximum-Likelihood Estimation, showing that the bias-corrected Maximum Likelihood Estimator was theoretically the most efficient. However, this earlier study i) ignored wood volumes; ii) neglected vegetation clumping inside the voxel; iii) ignored instrument characteristics in terms of effective footprint, iv) was limited to a single viewpoint. In practice, retrieving LAD from PAD is not straightforward, vegetation is not randomly distributed in volumes of interest, beams are divergent and forestry plots are usually sampled from more than one viewpoint, to mitigate the effect of occlusion. In the present short communication, we extend the previous efficient formulation to actual field conditions to i) account for the presence of both wood volumes and wood hits, ii) rigorously include correction terms for vegetation and instrument characteristics, iii) integrate multiview data. A numerical comparison with other methods commonly used to combine information from different viewpoints led to error reduction, especially in poorly-explored volumes, which are frequent in actual canopies. Beyond its concision, completeness and efficiency, this new formulation -which can be applied to multiview TLS, but also UAV LiDAR scanning - can help reducing errors in LAD estimation.

The main goal of the review is to provide a summary and an assessment of the potential of fast-growing tree species for suitable transformation of agroforestry areas for biomass production in the Baltic Sea region. The article summarizes the research on the management process of agroforestry zones by establishing short rotation plantations with tree species Salix spp., Populus spp., Alnus spp. and looks at the perspectives of planning of these zones as biomass producers. Short rotation forestry (SRF) with a combination of species and a rotation time of 15 to 30 years, depending on the species used, is the most suitable approach for management of these agroforestry zones. Willows (Salix spp.) and poplars (Populus spp.) are suitable for short rotation coppice (SRC), as these tree species can be harvested at much shorter intervals, respectively, 1–5 and 4–10 years, facilitating their use in agricultural systems. In Alnus spp. short rotation plantation the life cycle for energy wood production is assumed to be 15-30 years. The black alder plantations in agroforestry zones are used for sawnwood and firewood production, with a rotation span of 20–40 years. Calculated economic agroforestry zone repayment period is about 10-15 years, if costs and prices as in 2021 are used.

The aim of the work is to study the effect of the 3D printing process on the microstructural and hydrophilic properties of polylactic acid (PLA) samples with various model printing patterns obtained from the black Filament PLA by sequentially applying polymer layers using the FDM (Fused Deposition Modeling) method. X-ray phase analysis revealed partial crystallization of PLA polymer chains in printed samples, which occurs under thermal and mechanical action on the original amorphous PLA filament during 3D printing to varying degrees, depending on the geometry of the pattern and the morphology of its surface. At the same time, IR spectroscopy data indicate the preservation of all intrastructural chemical bonds of polylactide. Measured at the original installation, the values of the wetting edge angles on the surface of the printed samples are in the range φ = 50-60°, which is significantly less than the right angle. This indicates the hydrophilic properties of all samples’ surface. At the same time, the influence of different geometries of model drawings in printed samples was found not only on the morphology of the samples’ surface according to SEM data, but also on its wettability.

A three-year survey was conducted to estimate the incidence of grapevine trunk diseases (GTDs) in Greece and identify fungi associated with the disease complex. In total, 310 vineyards in different geographical regions in northern, central, and southern Greece were surveyed, and 533 fungal strains were isolated from diseased vines. Morphological, physiological and molecular (5.8S rRNA gene-ITS sequencing) analyses revealed that isolates belonged to 35 distinct fungal genera, including well-known (e.g. Botryosphaeria sp, Diaporthe spp., Eutypa sp., Diplodia sp., Fomitiporia sp., Phaeoacremonium spp., Phaeomoniella sp.) and lesser-known (e.g. Neosetophoma sp., Seimatosporium sp., Didymosphaeria sp., Kalmusia sp.) grapevine wood inhabitants. GTDs-inducing population structure differed significantly among the discrete geographical zones. Phaeomoniella chlamydospora (26.62%, n=70), Diaporthe spp. (18.25%, n=48) and F. mediterranea (10.27%, n=27) were the most prevalent in Heraklion, whereas D. seriata, Alternaria spp., P. chlamydospora and Fusarium spp. were predominant in Nemea (central Greece). In Amyntaio and Kavala (northern Greece), D. seriata was the most frequently isolated species (>50% frequency). Multi-genes (rDNA-ITS, LSU, tef1-α, tub2, act) sequencing of selected isolates, followed by pathogenicity tests revealed that Neosetophoma italica, Seimatosporium vitis, Didymosphaeria variabile and Kalmusia variispora caused wood infection with the former being the most virulent. To the best of our knowledge, this is the first report of N. italica associated with GTDs worldwide. This is also the first record of K. variispora, S. vitis and D. variabile associated with wood infection of grapevine in Greece. The potential associations of disease indices with vine age, cultivar, GTD-associated population structure and the prevailed meteorological conditions in different viticultural zones in Greece are presented and discussed.

Human-caused anthropogenic greenhouse emissions impact climate globally. In this pilot study, we aim to reveal the impact of oil and gas emissions from local oil deposits in the regime of their natural degradation and development and eco-physiological changes of pine forests in Tatarstan Republic, Russia over the past century. We performed stable carbon isotope analysis in pine tree rings (13Cptrw) to reveal the impact of oil and gas emissions from the giant oil field reservoirs located in Leninogorsk region (UVRT) and the natural reserve site in Raifa. Our results show decreasing 13Cptrw at UVRT in 1943 when oil extraction was started, and in 1970, when it reached the maximum production. We found that 13Cptrw from UVRT indicates on developing unfavourable drier conditions and suppressed tree growth caused by both human-induced oil and deposit infrastructure and natural processes compared to undisturbed Raifa. The 13Cptrw from Raifa is more negative compared to UVRT, which can be explained by higher forest sensitivity to human-induced impact. From an ecophysiological point of view decreasing intercellular to ambient CO2 concentration at the leaf level and increasing intrinsic water use efficiency along with decreasing tree-ring width at UVRT (1970-2021) indicate on development of drought conditions.

Compared to conventional allothermal gasification of solid fuels (e.g. biomass, charcoal, lignite etc.), plasma-assisted gasification offers an efficient method to apply energy into the gasification process to increase the flexibility of operation conditions and to increase the reaction kinetics. In particular, non-thermal plasmas (NTP) are promising, in which thermal equilibrium is not reached and electrons have substantially higher mean energy than gas molecules. Thus it is generally assumed that in NTP the supplied energy is utilized more efficiently for generating free radicals initiating gasification reactions than thermal plasma processes. In order to investigate this hypothesis, we compared purely thermal to non-thermal plasma assisted gasification of biomass in steam in a drop tube reactor at atmospheric pressure. The NTP was provided by means of gliding arcs between two electrodes aligned in the inlet steam flow. Electric power of about 1 kW was supplied using a high voltage generator operating at frequencies between 70 and 150 kHz and voltage amplitudes up to 10 kV. A laser-assisted optical method (Raman spectroscopy) was applied for measuring the gas temperature both in the conventionally heated steam and flow-down of the visible plasma filaments of the gliding arcs. Reaction yields and rates were evaluated using these measured gas temperatures. The first experimental results have shown that the non-thermal plasma not only promotes the carbon conversion of the fuel particles, but also accelerates the reaction kinetics. The carbon conversion is increased by nearly 10% using wood powder as the fuel. With charcoal powder more than 3% are converted into syngas.

We re-inventoried red wood ant nests (RWA) in 12 study sites (≈1281 ha) in the Westeifel Volcanic Field, Germany, in an area-wide and integrated ecosystem approach after 12 years. Combined with the re-identification of previously mapped nests using a photo database, this approach leads to more accurate nest counts in (re)inventories. A total increase of nests from 1144 (2009) to 1252 (2021), and a dramatic one for the Heidberg site by 52-fold (2009) and 85-fold (2021) compared to a 1984 inventory was observed, contrasting with earlier postulations of a decline in RWA. Early to medium mature (41-80 years) and mature (³81–140 years) spruce forests were the preferred habitat. Large increase in small nest sizes suggests an increase in new nest settlements also in clearings, despite climate-induced forest dieback over the past decade. A decline in biodiversity in the herbaceous layer was observed; highly proliferating blackberries had no negative impact on RWA nests. Monitoring of woodpecker cavities in RWA nests is suggested as an indirect indicator tool for evaluating populations in forests. Positive ground movement rates caused by the Eifel plume are suggested another factor favoring nest settlements. This study contributes to the urgent update of statistically valid data required to a) effectively substantiate the status-quo of RWA occurrences, b) protect RWA as ecosystem engineers, c) advance understanding of Geo-Bio-Interactions in the wake of climate change, and c) contribute to the German government's Insect Conservation Action Program.

Pine nuts are non-wood forest products (NWFP) with constantly growing market notwithstanding a series of phytosanitary issues and related trade problems. The aim of paper is to review the literature on the relationship between phytosanitary problems and trade development. Production and trade of pine nuts in Mediterranean Europe have been negatively affected by the spreading of Sphaeropsis sapinea (a fungus) associated to an adventive insect Leptoglossus occidentalis (fungal vector), with impacts on forest management activities, production and profitability and thus in value chain organization. Reduced availability of domestic production in markets with growing demand has stimulated the import of pine nuts. China has become a leading exporter of pine nuts, but its export is affected by a symptom associated to the nuts of some pine species: the ‘pine nut syndrome’ (PNS). Most of the studies embraced during the review are associated to PNS occurrence associated to the nuts of Pinus armandii. In the literature review we highlight the need for a comprehensive and interdisciplinary approach to the analysis of the pine nuts value chain organisation, where research on food properties and clinical toxicology be connected to breeding and forest management, forest pathology and entomology and trade development studies.