This study investigates the spatial and temporal distribution of litter at 7 beach sectors in Cadiz Bay, Southwest Spain. Two ten-day surveys carried out in autumn 2022 and spring 2023 revealed a total of 4,199 and 4,634 items, respectively, with plastic being the predominant material (71.13% in autumn, 88.39% in spring). Litter quantities varied significantly among beaches, La Puntilla showing the highest abundance with 0.48 ± 0.25 items m-1 in autumn and 1.34 ± 0.61 items m-1 in spring. The lowest abundance was recorded at sector 1 of Valdelagrana beach (0.08 ± 0.06 items m-1) during autumn and at El Castillito beach (0.08 ± 0.04 items m-1) during spring. Statistical analyses did not reveal significant differences in litter quantities between autumn and spring, however high significant interaction was shown considering both season and beach lo-cation. Seasonal differences were also observed in litter composition. Litter categories increased from 90 in autumn to 107 in spring. The top 10 litter categories varied between seasons and included cigarette butts, plastic fragments and plastic packaging. Cigarette butts were principally abundant in autumn because re-lated to summer beach users and wet wipes were particularly observed in spring because linked to wastewaters and river discharges especially relevant in winter months. Hydrodynamic and wind conditions were analyzed, revealing complex relationships with litter abundance.

The effectiveness of a recently proposed methodology in the identification of damage in planar, multi-storey, Reinforced Concrete (RC) moment-frames, which develop a plastic-yield mechanism on their beams, is showcased here via the examining of a group of such existing multi-storey frames with three or more unequal spans. According to the methodology, the diagram of the instantaneous Eigen-Frequencies of the frame in the nonlinear regime is drawn as a function of the inelastic seismic roof displacement by performing a sequence of pushover and instantaneous modal analyses with gradually increasing target displacement. Using this key-diagram, the locations of severe seismic damage in an existing moment-frame can be evaluated if the instantaneous fundamental eigen-frequency of the damaged frame, at an analysis step within the nonlinear area, is known in advance by “the monitoring and the identification of frequencies” using a local network of uniaxial accelerometers. This is a hybrid technique because both procedures, the instrumental Monitoring of the structure and the Pushover analysis on the frame (M and P technique), are combined. Moreover, the damage image of the planar multi-storey moment-frame is illustrated, and the lateral stiffness matrix of the damaged frame is calculated with high accuracy.

Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

The bacterial adhesion to food contact surfaces is a threat to human health, as these surfaces can serve as a reservoir of pathogenic bacteria. Escherichia coli is a biofilm-forming bacterium involved in surface contamination. Despite the application of disinfection protocols, contamination continues to occur. Hence, new effective and sustainable approaches are needed. Bacteriophages (or simply phages), viruses that only infect bacteria, have proven to be effective in reducing biofilms. Here, phage phT4A was applied to prevent and reduce E. coli biofilm on plastic and stainless steel. The assays were performed in Tryptic Soy Broth (TSB), at 25 °C. The biofilm formation capacity of phage-resistant and sensitive bacteria, after treatment, was also evaluated. Maximum reductions on E. coli biofilm of 5.5 log colony forming units (CFU)/cm2 (after 6 h) and 4.1 log CFU/cm2 (after 9 h), on plastic and stainless steel, respectively, were observed. In the prevention assays, phage prevented biofilm formation in 3.2 log CFU/cm2, after 12 h. Although the emergence of phage-resistant bacteria has been observed during phage treatment, a lower biofilm formation capacity was observed by phage-resistant bacteria comparatively to phage-sensitive bacteria. Overall, phages have shown to be a promising approach to decontaminate food handling surfaces.

We propose a spectral filter based on Plastic Optical Fiber with micro-holes as a low-cost, robust, and highly reproducible spectral filter. The spectral filter is explored for two configurations: fiber extended in a straight line, and a fiber optic loop mirror scheme configuration. The transmission traces indicate a spectral blue shift of peak transmission, at 587 nm, 567 nm, 556 nm, and 536 nm for 0, 1, 2, and 3 holes in the fiber, respectively. The filter exhibits a bandpass period of approximately 120 nm. Additionally, we conducted a comparison of the transmission with holes separated by distances of 1 cm and 500 μm. The results demonstrate that the distance between holes does not alter the spectral transmission of the filter. In the case of the fiber loop mirror configuration, we observed that the bandpass can be adjusted, suggesting the presence of multimode interference. Exploring variations in the refractive index within the holes by filling them with glucose solutions at various concentrations, we determined that the filtering band and spectral shape remains unaltered, ensuring a stable and robust operation of our spectral filter.

Every year since the last fifty years, the world is waking up to higher and higher average temperature of the earth. Initially it was thought that this trend is a part of cyclical warming and cooling of the earth and nothing to be much worried about. However, with weather conditions become erratic and unusual over a large swath of the planet more and more frequently and regularly, scientists started to speak of Climate Change and people started to listen. In this paper we briefly discuss the link between global warming, climate change and current policies in the developing world to drive home the urgent need for alternative thinking. We briefly discuss the theoretical link between economic development and greenhouse gas emission and lay the micro foundation of the Environmental Kuznets Curve (EKC) before providing some evidence of global climate change and why this is a matter of concern for social scientists. Then we explore two avenues through which human activities are aggravating the situation especially in developing countries – the role of business architecture and the role of built architecture. We argue that these twin architecture are aggravating global warming by moving away from sustainable development policies.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

The seismic damage in reinforced concrete bridges is identified in this study using the "M and P" hybrid technique initially developed for planar frames. The proposed methodology involves a series of pushover and instantaneous modal analyses with a progressively increasing target deck displacement along the longitudinal direction of the bridge. From the results of these analyses, the diagram of the instantaneous eigenfrequency of the bridge, ranging from the health state to near collapse, is plotted against the inelastic seismic deck displacement. By pre-determining the eigen-frequency of an existing bridge along its longitudinal direction through "monitoring and frequency identification", the target deck displacement corresponding to the damage state can directly be found from this diagram. Subsequently, the damage can be identified by examining the results of the pushover analysis at the step where the target deck displacement is indicated. The effectiveness of this proposed technique is evaluated in the context of multiple span bridges with unequal pier heights, illustrated through an example of a four-span bridge. The findings demonstrate that the damage potential in bridge piers can be successfully identified by combining the results of a monitoring process and pushover analysis.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

The amount and composition of litter was evaluated, during May and June 2021, at two urban beaches, i.e. La Victoria and La Cortadura, in Cadiz, SW Spain. Surveys were daily carried out in the morning and in the evening during the week−ends to quantify the daily accumulation of beach litter and relate it with the number of beach users, which was assessed at around 1:00 p.m. Litter amount was also related to clean-up operations that very mechanically and manually carried out each day very early in the morning. A total of 8108 items were collected at the two investigated sectors during the study period and beach visitors were quantified in each one of 22 surveys. Plastic was the most common material representing 82% in La Victoria and 68% in La Cortadura. The most common items were cigarette butts and small hard plastic fragments. Some hazardous litter items for beach visitors were identified such as broken glass. The number of visitors has been positively related to the amount of litter. Significant differences were seen in the litter abundance between the morning and afternoon assessments since the beaches are daily cleaned and show bins to facilitate litter disposal. Cleaning operations remove much of the litter items but always leave low quantities of small items uncollected. Efforts to prevent litter on these beaches should focus on informing visitors properly in order to avoid dumping and on improving clean-up operations.

Syndactyly is the most common congenital malformation of the hand, leading to the fusion of the digits, frequently affecting the ring and middle fingers. The incidence is one out of 2500 children, predominantly occurring in boys and Caucasians. Clinically, the malformation may present as soft tissue or bony fusion, resulting in the union of the fingers characterised as complete or incomplete. This fusion may involve the phalanges but may also extend to the carpal/tarsal bones, even to the metacarpal’s or metatarsal’s level, rarely to the distal end of the forearm and lower leg. Mostly isolated but may occur together with other disorders or malformations such as synostosis, acro-syndactyly, cleft hand, clinodactyly, or polydactyly. Syndromic syndactyly can be observed in cases of Apert Syndrome, Poland’s Syndrome, Pfeiffer Syndrome and many others. A girl born in June of 2019 was diagnosed with congenital malformation of the right hand at birth —affecting the right middle, ring and little fingers, respectively. After X-ray imaging, the fusion of the third and fourth proximal phalanges to a common metacarpal was identified, forming a unique diagnosis of clino-syndactyly with metacarpal aplasia. Surgical intervention was advocated for, including a wedge osteotomy to correct the synchondrosis at the phalangeal base and a dorsal flap to close the interdigital space created during the correction of the III and IV. fingers. A trapezoid flap for the release of the syndactyly of the IV and V. fingers was applied. The paper aims to present the surgical correction and its results regarding an atypical case of syndactyly with clinodactyly and metacarpal aplasia.

A tumbler screen type residual film–impurity mixture wind separator as a key equipment for secondary utilization of farmland residual film. During the working process, the proportion of impurities in the separated waste mulch film intermittently increases, resulting in poor working stability of the device, which may hamper long-term operation. In this study, the material inside the separation unit was continuously monitored, and the main factor affecting separator per-formance was determined to be the challenges in the effective depolymerization of some residual film–impurity mixtures. The principles of agglomeration and depolymerization of the residual film–impurity mixtures were analyzed using computational fluid dynamics (CFD) and discrete element method (DEM) flow-solid coupling simulation methods. The key factor affecting the disaggregation of the mixture was the collision force between the residual film–impurity mixture and the trommel screen. The collision force was maximum when the residual film–impurity mixture first collided with the trommel screen when it was fed into the separation device. As determined by force analyses, the key factors affecting the collision force of the process were the material feeding amount and the structure of the inlet. Furthermore, simulations were carried out for different inlet structure forms; the evaluation index was the maximum collision force of the residual film–impurity mixture agglomerate on the trommel screen. The best disaggregation effect was obtained with a square feed inlet and at a feeding rate of 202 kg/h. A prototype was built using these specifications for verification. The average value of the ratio of impurities in the re-sidual film was 6.966%, the coefficient of variation was 7.38%, and the dispersion of statistical results was small. The ratio of impurities in the residual film was kept constant during the con-tinuous operation of the wind separator. Thus, this study analyzed the agglomerate disaggregation process and provided theoretical insights for deter-mining the optimal structures of the inlets of various cleaning devices and the feeding volumes.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

Keywords: Fatigue crack propagation; Welding residual stress; Plastic re-distribution; Stress ratio effect

The present article investigates the threshold analysis of yielding in a variable thickness rotating disk based on the Tresca criterion. The analysis is conducted on a Functionally Graded Material (FGM) constructed from tailored materials, following the theory of small deformations and for the case of plane stress. The elasticity modulus, density, and yield stress are assumed to be power functions of the radial coordinate. Poisson’s ratio is considered constant due to small variations in different materials. Additionally, the governing equation for the rotating disk is solved analytically. Besides the material type, another factor affecting the distribution of effective stress magnitudes is the cross-sectional shape (profile) of the disk. The thickness of the cross-sectional disk varies radially as a power function. In the current analysis, different conditions for the onset of yielding and the evolution of plastic flow are considered. For evaluation and validation, the obtained results are compared and validated against similar results for specific cases (homogeneous disk and constant thickness graded disk) available in previous references. The results indicate that considering variable thickness for the disk section significantly affects the stresses and the location of the initiation of yielding

Plastic contamination of small dimensions (

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

Co-Zr amorphous alloys exhibit soft magnetic properties, whereas Co-rich crystalline magnetic phases in this alloy system display hard magnetic behaviour. In this study, an initial two-phase Co-Zr composite with an overall composition of 75 at.% Co and 25 at.% Zr was processed by high pressure torsion (HPT) and the effects of severe plastic deformation and subsequent thermal treatment on the structural evolution and its magnetic properties have been investigated. HPT processing allowed us to achieve an amorphous microstructure in the as-deformed state with low coercivity. To further tune magnetic properties and study the alloys’ crystallization behaviour, various annealed states are investigated. Microstructural properties are correlated to the magnetic properties and a decreasing coercivity with increasing annealing temperature is observed despite the onset of crystallization in the amorphous alloy. At higher annealing temperatures, coercivity increases again. The results appear promising to obtain tuneable rare-earth free magnetic materials by severe plastic deformation.

Nanoindentation load-depth (P-h) plots is the basis for determination of mechanical properties of the samples and is especially vital for thin coatings deposited on substrates of various mechanical makeup from amorphous-brittle (borosilicate glass) to Silicon (having different crystallographic texture) to ductile substrates like stainless steel as well other aspects like indenter tip shape. The elastic-plastic response by simulated P-h plots as per modified empirical relations have been presented. The outcomes of this computational studies enlighten the database on the P-h plots for various coating/substrate systems and shall aid in the analysis of experimental P-h plots obtained,

Effects of plastic deformation on the indentation feature of hot-rolled commercial pure titanium alloy were detected using microindentation. It was found that the most deformed sample experienced the largest indentation resistance and had the maximum dislocation density and the indentation size influenced the CP-Ti indentation feature. The Vicker hardness and energy dissipated demonstrated the significant influence of the dislocation motion and size effects on the indentation in the indentation deformation. The linear relation of the energy ratio which is related to the microstructures and the indentation depth ratio was obtained for hcp materials Titanium alloys.

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

Calcium sulphate (CS) is currently used as a bioabsorbable, completely synthetic and sterile material in the management of infected tissues and dead spaces (DS) mainly resulting from surgical procedures. Residual DS in the postoperative, may create an environment where hematomas fill up and bacteria can proliferate, leading to a high incidence of postoperative infections. Considering the available reviews in the literature, CS has been mainly studied in orthopedic surgery mostly giving brilliant results and low complication rates. Nowadays, orthopedists avail it in the form of pearls both as a bone void filler and as an “off-label” delivery agent for antibiotics in arthroplasty, chronic osteomyelitis and open fractures, paving the way of its application in many other contexts given its natural dis-position to biodegradation. In the last years, CS beads have been gaining ground in the general, vascular and endocrinological surgical specialties. Despite its clear potential and the increasing number of scientific evidences on the safety and effectiveness of CS application in the prophylaxis and treatment of infections, there are not many studies reporting on its application in fields other than orthopedics, with a substantial paucity in plastic and reconstructive surgery literature. This is some-how surprising, since reconstructive surgery often deals with complex wounds secondary to bone and soft tissue exposure, suture dehiscence, trauma, and surgical site infections. As far as we know this is the first updated systematic review assessing the state of the art, indications and new perspectives on the application of CS beads in plastic and reconstructive surgery.