Fatigue failure remains a critical concern in structural engineering and material science, prompting extensive research to understand and predict the behaviour of materials under cyclic loading conditions. The present study aims to investigate the fatigue life of carbon steel specimens containing opposite semicircular edge notches through a comprehensive experimental and numerical analysis. In this study, stress concentration factors (SCF, K_t) of rectangular plate with opposite semicircular notches are considered under uniform tensile stress to analyse the notch deformation because of stretching of plate. Furthermore, the research focuses on quantifying stress concentration factors (SCFs) for these notches based on S-N curves of carbon steel. The study employs a combination of experimental and numerical techniques to understand the influence of these notches on the fatigue performance of carbon steel structures. A plate with opposite semicircular edge single notches under the axial load creates stress concentration near the notch and it is much larger than the average stress on the plate. Both analytical and finite element methods are used to calculate the maximum stress around the notch. SOLIDWORKS Premium Student Edition 2023 has been employed for modelling and SOLIDWORKS Simulation Premium Student Edition 2023 has been used for stress analysis and fatigue notch factor of rectangular plate of size 31 mm x 25.4 mm x 6.35 mm. The uniform tensile load with a magnitude of 20195 N is applied on one sides of rectangular plate normal to the sides of notches with ratio h/r = 1, for the semicircular notch. The result obtained on both analytical and finite element methods are compared and the percentage of error has been evaluated. Subsequently, these specimens undergo fatigue testing under varying loading conditions to capture their fatigue behaviour. The acquired fatigue data is then plotted against stress amplitude to construct S-N curves, forming the foundation for assessing the fatigue life of the notched specimens. To complement the experimental findings and to gain a deeper understanding of the stress concentration phenomenon, numerical simulations are conducted using advanced finite element analysis (FEA) techniques. The finite element models are carefully calibrated against the experimental results to ensure their accuracy and reliability. The FEA simulations enable the determination of stress concentration factors at critical locations within the notched specimens, further validating the experimental observations. The investigation reveals crucial insights into the effect of opposite semicircular edge notches on the fatigue life of carbon steel structures. The obtained S-N curves allow engineers and designers to predict the fatigue life of components with similar notches, aiding in the development of reliable and durable structures in practical applications. Moreover, the stress concentration factors determined from the numerical simulations provide valuable data to assess the potential failure modes and to optimise designs, effectively mitigating fatigue-related failures. The combination of experimental and numerical approaches ensures a comprehensive and rigorous analysis of the fatigue behaviour in notched specimens, offering a reliable basis for making informed engineering decisions. The comparison between the analytical method and the Finite Element Method (FEM) demonstrated good agreement, with an error percentage of 4.272%. The analysis revealed that the specimen would experience failure after approximately 2882 cycles, with a maximum stress of 395.914 MPa. This research study enhances the understanding of fatigue life in carbon steel structures containing opposite semicircular edge notches and contributes valuable data to the field of fatigue mechanics. The outcomes serve as a valuable resource for professionals engaged in structural engineering, material science, and design optimisation, ultimately leading to safer and more durable industrial components in critical applications. The findings of this research contribute to the understanding of fatigue behaviour in carbon steel components with stress concentration effects caused by semicircular notches. Moreover, the validated numerical simulations and data curves facilitate the prediction of fatigue life and aid in determining the critical conditions leading to fatigue failure. In conclusion, this research highlights the significance of combining experimental testing with numerical simulations to comprehensively analyse the fatigue life of carbon steel specimens with opposite semicircular edge notches. The obtained stress concentration factors provide crucial information for structural integrity assessment and offer potential for further optimising design criteria to mitigate fatigue-related failures. The findings of this study could play a vital role in enhancing the reliability and safety of carbon steel structures subjected to cyclic loading conditions. The comprehensive experimental and numerical analyses establish a foundation for future studies exploring other materials and geometries with notches, fostering advancements in fatigue life prediction and structural integrity assessment.

Tropical sea surface temperature (SST) variability, mainly driven by the El Niño–Southern Oscillation (ENSO), influences the atmospheric circulation and hence the transport of heat and chemical species in both the troposphere and stratosphere. This paper uses Met Office, ERA5 and MERRA2 reanalysis data to examine the impact of SST variability on the dynamics of the polar stratosphere and ozone layer over the period 1980 to 2020. Particular attention is paid to studying the differences in the influence of different types of ENSO (East Pacific (EP) and Central Pacific (CP)) for the El Niño and La Niña phases. It is shown that during the EP El Niño, the zonal wind weakens more strongly and changes direction more often than during the EP El Niño, and the CP El Niño leads to a more rapid decay of the polar vortex (PV), an increase in stratospheric air temperature and an increase in the concentration and total column ozone than during EP El Niño. For the CP La Niña, the PV is more stable, which often leads to a significant decrease in Arctic ozone. During EP La Niña, powerful sudden stratospheric warmings are often observed, which lead to the destruction of PV and an increase in column ozone.

Bacterial transformation is the essential tool for introducing foreign DNA into bacterial cells in a host of recombinant technology applications useful for biomanufacturing and drug production. Thus far, chemically competent cells remain an important enabling technology for bacterial transformation given its facile transformation approach. However, many parameters affect transformation efficiency, and there is relatively little documentation of their cross-interacting effect in the literature. This work explores the roles played by incubation time on ice, competent cell concentration, and plasmid-to-cell ratio on transformation efficiency in Escherichia coli DH5α. Results revealed that increases in incubation time improve transformation efficiency, but 2 minutes incubation still yield appreciable efficiency. On the other hand, low concentration competent cells (10⁶ CFU/mL) yielded significant improvement in transformation efficiency compared to high concentration competent cells (10⁸ CFU/mL). In terms of plasmid-to-cell ratio, higher ratio increases transformation efficiency. Overall, bacterial transformation is incompletely understood particularly in the area of cross-interacting parameters. Experiments reported here revealed the possibility of short duration transformation where lower competent cell concentration and higher plasmid-to-cell ratio could improve transformation.

Trash mulches are very effective in preventing soil erosion; reduce sediment transport rate, runoff rate and increasing infiltration. The study was carried out with the objectives to observe the sediment outflow from sugar cane leaf (trash) mulch treatments at selected land slopes under simulated rainfall conditions by using rainfall simulator of size 10 m × 1.2 m × 0.5 m with the locally available soil material collected from Pantnagar. In the present study, trash mulches with different quantities were selected to observe the effect of mulching in soil loss reduction. The quantity of mulch was taken as, 6 t/ha, 8 t/ha and 10 t/ha, three rainfall intensities viz. 11cm/h, 13cm/h and 14.65cm/h at 0%, 2% and 4% land slopes were selected. The duration of rainfall was fixed (10 minutes) for every mulch treatment. The total runoff volume was found to be varying with different mulch rates for particular rainfall input and land slope. The runoff distribution pattern was observed to be increasing with the increase in land slope. The average sediment concentration (SC) and outflow was found to be increasing with the increasing land slope, but SC and outflow decreased with increasing mulch rate for particular land slope and rainfall intensity. The SOR (SOR) for no mulch treated land was higher as compared to trash mulch treated lands. Mathematical relationships were developed for relating SOR, SC, land slope and rainfall intensity for a particular mulch treatment. It was observed that values of SOR and average SC had a good correlation with rainfall intensity and land slope for each mulch treatment. The correlation coefficients of developed models were found to be more than 90%.

Immersion in salt-lake solution was adopted to periodically test the concrete chloride-ion diffusion coefficient. The regression analysis was also completed. Also investigated was the time-dependent law of concrete chloride-ion diffusion coefficient with time. The influence of chloride-ion concentration in solution, water-to-cement ratio, and corrosion time on the largeness and accumulation rate of the concrete chloride-ion diffusion coefficient was also analyzed. Test results show that the concrete chloride-ion diffusion coefficient gradually decreased with increasing time and increased with increasing chloride-ion concentration in a salt lake . Taking into account the influence of factors such as water–binder ratio, chloride-ion concentration, and time-varying characteristics, a multi-factor calculation model for the concrete chloride-ion diffusion coefficient was established. Combining the prediction results and the measured data reported in this paper, the effectiveness and applicability of the established concrete chloride-ion diffusion coefficient calculation model were compared and verified, and the durability design and service life of a concrete structure under cool chlorine were compared. The results of analysis provide important boundary conditions.

This article describes in detail the numerical modeling of a CZTS (copper zinc tin sulfide) based kesterite solar cell. The Solar Cell Capacitance Simulator -one-dimension (SCAPS-1D) software was used to simulate MO/CZTS/CdS/ZnO/FTO structured solar cells. The parameters of different photovoltaic thin-film solar cells are estimated and analyzed using numerical modeling. The effects of various parameters on the performance of the photovoltaic cell and the conversion efficiency are discussed. Since the response of the solar cell is also contingent on its internal physical mechanism, J-V characteristic measures are insufficient to characterize the behavior of a device. Different features, as well as different potential conditions, must be considered for simulation, disregarding the belief in the modeling of a solar cell. With a conversion efficiency of 25.72%, a fill factor of 83.75%, a short-circuit current of 32.96436 mA/cm2 and an open-circuit voltage of 0.64V, promising optimized results have been achieved. The findings will be useful in determining the feasibility of fabricating high-efficiency CZTS-based photovoltaic cells. The efficiency of a CZTS-based experimental solar cell is also discussed. First, the effects of experimentally developed CZTS solar cells are simulated in the SCAPS-1D environment. The experimental results are then compared to the SCAPS-1D simulated results. The conversion efficiency of an optimized system increases after cell parameters are optimized. Using one-dimensional SCAPS-1D software, the effect of system parameters such as the thickness, acceptor and donor carrier concentration densities of absorber and electron transport layers, and the effect of temperature on the efficiency of CZTS-based photovoltaic cells is investigated. The proposed results will greatly assist engineers and researchers in determining the best method for optimizing solar cell efficiency, as well as in the development of efficient CZTS-based solar cells.

Background: Globally, hot cooked refined rice is consumed in large quantities and is a major contributor to dietary glycaemic load. This study aimed to compare the glycaemic potency of hot and cold stored parboiled rice to widely available medium grain white rice. Method: Twenty-eight healthy volunteers participated in a three treatment experiment where postprandial blood glucose was measured over 120 minutes after consumption of 140g of rice. Three rice samples were freshly cooked medium-grain white rice, freshly cooked parboiled rice, and parboiled rice stored overnight at 4 ºC. All rice was served warm at 65 ºC. Chewing time was recorded. Results: The 24-hours cold-stored and reheated parboiled rice resulted in a 42% and 12% lower blood glucose concentration trajectory than freshly cooked medium-grain white rice and freshly cooked parboiled rice. Chewing time for 10g cold stored parboiled rice was 6 seconds (25%) longer and was considered more palatable, visually appealing and better tasting than freshly cooked medium grain (all P<0.05). Conclusions:. For regular consumers of rice reheating cooked rice after cold storage would lower the dietary glycaemic load and long term may reduce risk for type 2 and gestational diabetes. More trials are needed to identify the significance.

This study examines the impact of chainsaw chain type and tree species on the concen-tration of inhalable wood dust generated during motor-manual harvesting in forested areas. The chainsaw chain is a critical component, contributing not only to productivity but also to the oper-ator's health and safety. Wood dust creation during harvesting operations poses significant risks and necessitates careful attention due to its potential health effects. We investigated the effects by conducting real-world measurements of inhalable dust within the operator's breathing zone during forestry work. Two different chain types were evaluated: the commonly used 3/8" pitch chain (conventional chain) and the 0.325" pitch chain. Additionally, measurements were taken for three tree species: beech, oak, and pine (including both live and standing dead trees after a fire). Results showed that, overall, using the conventional 3/8" chain type yielded the highest concentration of wood dust for all three tree species. Notably, the highest wood dust concentration was observed in the burned Pinus brutia cluster, also with the 3/8" chain pitch. These findings emphasize the im-portance of understanding how chain type and tree species contribute to wood dust levels and provide valuable insights for enhancing operator health and safety during motor-manual har-vesting operations

High-entropy alloys (HEAs) are of great interest in the field of materials science and engineering. Unlike conventional alloys, which contain a maximum of two base metals, this new category of materials consists of multi-principle elements and the possible number of alloy compositions, in case of HEAs, is outstandingly higher than that for conventional alloys. Here, a review on the high-entropy alloys, has been provided, on the issue whether the earliest definition of High- Entropy alloys, proposed in 2004^{[2, 4]}, is consistent with one of the four-component equiatomic Compositionally complex alloys exhibiting a “High-entropy” effect.

Easy to use satellite-based water quality visualizations are needed for monitoring and understanding coastal and inland waters, but to date, no publicly accessible real-time global visualization system was in place. Here we introduce the Ulyssys Water Quality Viewer (UWQV), a Sentinel Hub EO Browser Custom script designed for qualitative views of aquatic chlorophyll and suspended sediment concentrations. The viewer avoids unmixing of the chlorophyll and suspended sediment spectral signal by visualizing these parameters together, with high concentrations of suspended sediment obscuring chlorophyll if present. Cloud masking uses the Hollstein and Braaten algorithms (existing EO Browser custom script code), additionally water surfaces are masked using the Normalized Differential Water Index. Chlorophyll is estimated using reflectance line height-based indicators such as fluorescence line height and maximum chlorophyll index. Suspended sediment is visualized based on single-band reflectances at 620 or 700 nm. Data sources are Sentinel-2 and Sentinel-3 images, allowing either 20 m spatial resolution or up to daily imaging. This visualization system is easy to operate and interpret, and combined with the data service capacity of the Sentinel Hub, it is expected that UWQV will contribute to monitoring of remote water bodies and to our overall understanding of physical limnology and aquatic ecology.

Normally, the Nernst voltage calculated from the concentration of the reaction gas in the flow channel is considered to be the ideal voltage (reversible voltage) of the oxyhydrogen fuel cell, but actually it will cause a concentration gradient when the reaction gas flows from the flow channel through the gas diffusion layer to the catalyst layer. The Nernst voltage loss in fuel cells in most of the current literature is thought to be due to the difference in concentration of reaction gas in the flow channel and concentration of reaction gas on the catalyst layer at the time when the high net current density is generated. Based on the Butler-Volmer equation in oxyhydrogen fuel cell, this paper demonstrates that the Nernst voltage loss is caused by the concentration difference of reaction gas in flow channel and on the catalytic layer at the time when equilibrium potential (Galvanic potential) of each electrode is generated.

The article presents the results of tests of minor head losses through PVC and PP elbows for a flow of water and mixtures of water and sand with grain sizes of up to 0.5 mm and concentrations of 5.6 g∙L-1, 10.84 g∙L-1, and 15.73 g∙L-1. The tests were carried out at variable flow velocities for three elbow diameters of 63, 75, and 90 mm. The flow rate, pressure difference in the tested cross-sections, and temperature of the fluids were measured and automatically recorded. The results of the measurements were used to develop mathematical models for determining the minor head loss coefficient as a function of elbow diameter, sand concentration in the liquid, and Reynolds number. The mathematical model was developed by cross validation. It was shown that when the concentration of sand in the liquid was increased by 1.0 g∙L-1, the coefficient of minor head loss through the elbows increased, in the Reynolds number range of 4.6∙104 − 2.1∙105, by 0.3−0.01% for PP63, 0.6−0.03 % for PP75, 1.1−0.06 % for PP90, 0.8−0.01 % for PVC63, 0.8−0.02 % for PVC75, and 0.9−0.04 % for PVC90. An increase in Re from 5∙104 to 2∙106 for elbows with diameters of 63, 75 and 90 mm caused a 7.3 %, 6.8 %, and 6.0 % decrease in the minor head loss coefficient, respectively.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

Cemented rock fill (CRF) is commonly used in cut-and-fill stoping operation in underground mining. This allows for the maximum recovery of ore. Backfilling can improve stope stability in underground workings, and then improve ground stability of the whole mine site. Backfilling step scenarios vary from site to site. This paper presents the investigation of five different backfilling step scenarios and their impacts on the stability of stopes at four different mining levels. A comprehensive comparison of displacements, major principal stress and stress concentration factor (SCF) was conducted. The results show that different backfilling step scenarios have little influence on the final displacement for displacement in the stopes. Among the five backfilling scenarios, the major principal stress and stress concentration factor (SCF) have almost the same final results. The backfilling scenario SCN-1 is the optimum option among these five backfilling scenarios. It can immediately prevent the increase of the displacement and reduce the sidewall stress concentration, thereby preventing possible failures. Using the same strength of CRF can achieve same effects among the four mining levels. Applying backfilling CRF of the same strength at different mining depths is acceptable and feasible to improve the stability of the stopes.

The goal of this study was to determine the relative susceptibility of four common equine wound pathogens to ten different types of antimicrobial agents based on minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC). Additionally, to describe the comparison of bactericidal activity of medical grade Manuka honey, local honey, and commercial, food-grade honey to other commonly used wound dressings. The objective is to provide veterinary practitioners with comparative data on the use of a variety of antimicrobial dressings for inhibiting growth of common wound bacteria. MIC and MBC for Manuka, store, and local honeys were comparable to those of sterile gauze, sugar, and hypertonic saline. Across bacterial species, local honey proved to have more bactericidal activity when compared to Manuka and commercial, food-grade honey. The MIC and MBC for PHMB gauze and foam was consistently at a higher dilution compared to the other antimicrobials. The majority of antimicrobials exhibited stronger inhibitory and bactericidal activity against a Streptococcus zooepidemicus isolate obtained from a wound compared to other bacteria that were ATCC lab acclimated. Additional research for in-vivo applications needs to be done to see whether differences exist in effective wound management.

In this report, we establish a straightforward method for estimating the equilibrium constant for the CK reaction over wide but physiologically and experimentally relevant ranges of pH, Mg2+ and temperature. Our empirical formula for CK Keq” is based on experimental measurements. It can be used to estimate [ADP] when [ADP] is below the resolution of experimental measurements, a typical situation because [ADP] is on the order of micromolar concentrations in living cells, and may be much lower in many in vitro experiments. Accurate prediction of [ADP] is essential for in vivo studies of cellular energetics and metabolism, and for in vitro studies of ATP-dependent enzyme function under near-physiological conditions. With [ADP], we could estimate ΔGATP. Application to actomyosin force generation in muscle provides support for the hypothesis that, when [Pi] varies but not when pH is altered, maximum Ca2+-activated isometric force depends on ΔGATP in both living and permeabilized muscle preparations. Further analysis of the pH studies introduces a novel hypothesis for the role of submicromolar ADP in force generation.

Sustainable development of our society demands recycling of metallic wastes which may contain a variety of metallic impurities. Thus, it is desirable to develop a ‘universal’ structure, such as an amorphous alloy tolerating high concentrations of metallic pollutants. We performed ab initio molecular dynamics simulations to manufacture a novel multicomponent amorphous alloy of twenty elements (20e-HEAA). Analysis reveals both topological and chemical compositional short-range ordering in the obtained 20e-HEAA and formation of B-B clusters. Electronic structure calculations reveal the metallic nature of the amorphous alloy with its Fermi level falling in a valley in the density of states. Moreover, the Zn 3d and Cd 4d electrons exhibit a localized nature and thus, should be excluded from the valence electron concentration (VEC) analysis in the study of high-entropy alloys. The information obtained here is helpful to get insight into multicomponent high entropy materials, especially multicomponent high-entropy amorphous alloys as potential circular metals.

Background: The burden of resistant fungal infection is rising in patients with pulmonary disease. Options for antifungal therapy are limited, and the only orally-available antifungals, the triazoles, demonstrate inter and intra-patient variability, non-linear kinetics, toxicity, drug interactions and increasing antifungal resistance. Therapeutic drug monitoring (TDM) of itraconazole, voriconazole and posaconazole has been necessary to ensure their safety and efficacy, but is considered unnecessary for the newest triazole isavuconazole, use of which is increasing. Aims: To characterise isavuconazole susceptibility of Aspergillus fumigatus isolates in a tertiary respiratory referral centre to understand prevalence of isavuconazole antimicrobial resistance. To retrospectively review experience of isavuconazole use in this setting, assessing tolerability and therapeutic drug monitoring. Methods: A retrospective observational analysis of adult patients with respiratory disease in a tertiary hospital setting between Sept 2016 and Aug 2021. Clinical cultures were collected and triazole Minimum inhibitory concentration (MIC) were recorded (based on Clinical &amp; Laboratory Standards Institute (CLSI method)). Isavuconazole trough drug levels were carried out as part of the standard of care. Clinical outcomes of treatment were evaluated, along with drug tolerance and TDM. Results: During the study period, isavuconazole susceptibility testing was performed on 26 Aspergillus spp isolates. 80.8% of Aspergillus fumigatus isolates were non-wild type and had isavuconazole MIC &gt; 1mg/L, and 73.0% had MIC above the EUCAST (European Committee on Antimicrobial Susceptibility Testing) epidemiological cut-off (ECOFF) of 2mg/L. There was good correlation between isavuconazole MIC and voriconazole MIC (r =0.7, p=0.0002). 54 patients had isavuconazole therapy over the study period with a median duration of 7.7 months (IQR 0.79 - 16.42). 67% of patients were able to tolerate isavuconazole, despite toxicity with prior azole treatment being the primary indication for use (in 61.8%). Increased age (r=0.29; p=0.03 (95%CI 0.02,0.52)) and gender (r for female sex=-0.31; p=0.027 (95%CI -0.52,0.036) were associated risk factors for development of adverse events (AEs). 127 Isavuconazole TDM levels were performed over the study period with 90% &gt;1mg/L and 72% &gt;2mg/L. Dose change from manufacturer’s dose recommendation, however, was required in 15% of patients to achieve a serum drug concentration above the EUCAST ECOFF or Area of technical uncertainty (ATU) value of 2mg/L. Conclusion: In our study, we show use of Isavuconazole as salvage therapy in chronic pulmonary fungal disease setting with high prevalence of azole resistance. Isavuconazole MICs demonstrated good correlation with voriconazole MICs suggesting the latter could be a useful surrogate marker for isavuconazole susceptibility. Although Isavuconazole achieved excellent serum drug concentrations at standard dose compared to other azole drugs, we highlight the importance of antifungal stewardship and TDM monitoring to optimise therapy in this setting.

Although a slightly radioactive element, thorium is considered very toxic because its various species, which reach the environment, can constitute an important problem for the health of the population. The present paper aims to expand the possibilities of using membrane processes in the removal, recovery and recycling of thorium from industrial residues reaching the municipal waste processing platforms. The paper includes a short introduction on the interest shown for this element, a weak radioactive metal, followed by highlighting of some common (domestic) uses. In a distinct but concise part, the bio-medical impact of thorium is presented. The classic technologies for obtaining thorium are concentrated in a single schema, and then the speciation of thorium is presented with an emphasis on the formation of hydroxo-complexes and complexes with common organic reagents. The determination of thorium has been highlighted both on the basis of its radioactivity, but especially through methods that call for extraction followed by an established electrochemical, spectral or chromatographic method. Membrane processes are presented based on the electrochemical potential difference, rapidly presenting barro-membrane processes, electrodialysis, liquid membranes and hybrid processes. A separate sub-chapter is devoted to proposals and recommendations for the use of membranes in order to achieve some progress in urban mining for the valorization of thorium.

Chronoamperometric curves of the oxidation of a ferrocenyl derivative by the potential step showed diffusion controlled-like currents less than the Cottrell's equation at a platinum wire electrode. The lower deviation cannot be explained by the Butler-Volmer heterogeneous kinetics, but was ascribed to the negatively capacitive current associated with the redox reaction. The deviation at the fully oxidized potential corresponds to the non-zero concentration at the electrode surface, which cannot be predicted from the Nernst equation. The Nernst equation expresses the relationship of the potential with the activity at the electrode surface rather than the concentration. The diffusion equation provides the relation of the current with the surface concentration rather than the activity. The negative capacitance or the non-zero concentration may arise from structure formation on the electrode owing to the dipole-dipole interaction, which is similar to the generation of the double layer capacitance including frequency dispersion. On this concept, we derive here expressions for the lowered diffusion-controlled current and the time-dependent surface concentration. The negatively capacitive current shows the time-dependence of t-0.9, which is similar to the decay of the double layer capacitive currents. The surface concentration decays with the t-0.4-dependence.

Higher traffic density in Russian cities and less uniform traffic due to congestions are reasons for increased emissions of pollutants contained in exhaust gases of vehicles. The paper presents the modeling results of pollutant dispersion in Magnitogorsk. The analysis of these results shows that now many blocks of flats and social infrastructure of the city are in a zone with an excess of maximum allowable concentration of pollutants. Having summarized the methodological framework formulated by Russian and foreign researchers, the authors systemized the existing methods used to decrease pollutants produced by vehicles. It is proposed to choose an optimal combination of such methods applying a developed mathematical model. By adopting an optimal combination of the methods, it is possible to ensure minimum air pollutant emissions from vehicles, allocating limited financial resources. The mathematical modeling of the solutions on changing traffic density and structure and implementing methods used to decrease pollutants on one of the Magnitogorsk crossroads with the heaviest traffic is used to draw a conclusion about efficiency of the designed model used as a tool for strategic planning of development and transformation of street networks.

We propose a non-invasive approach to control the quality of spheroids and their fusion into a complex bioconstruct. The proposed method is based on the union of the nutrient concentration change calculated using Fick's law and the "reaction-diffusion" equations, taking into account absorption coefficient with specifying the exact fusion geometry using implicit Function Repre-sentation (FRep) functions. The proposed approach allows us to analyze the viability of cells within the spheroid, predict the fusion of spheroids, and accurately model complex heteroge-neous biostructures as a future task for our research. These results will significantly accelerate the development of such a promising field of additive biotechnologies as 3D bioprinting.

Human exposure to infectious aerosols results a transmission of diseases, such as influenza, tuberculosis, and COVID-19. Most dental procedures generate a significant number of aerosolized particles, increasing transmission risk in dental settings. Since the generation of aerosols in dentistry is unavoidable, many clinics started using intervention strategies such as area-filtration units and extraoral evacuation equipment, especially under the relatively recent constraints of the pandemics. However, the effectiveness of these devices in dental operatories has not been studied. Therefore, the dental personnel's ability to position and operate such instruments efficiently is also limited. To address these challenges, we utilized a real-time sensor network for assessment of aerosol dynamics during dental restoration and cleaning producers with and without intervention. The strategies tested during the procedures were (i) local area high-efficiency particle air (HEPA) filters and (ii) extra-oral suction device (EOSD). The study was conducted at the University of Washington School of Dentistry using a network of thirteen fixed sensors positioned within the operatory and one wearable sensor worn by the dental operator. The sensor network provides time and space-resolved particulate matter (PM) data. Three-dimensional (3D) visualization informs aerosol persistence in the operatory. It was found that area filters did not improve the overall aerosol concentration in dental offices significantly. An average of 16% decrease in PM concentration was observed when EOSD equipment was used during the procedures. The combination of real-time sensors and 3D visualization can provide dental personnel and facility mangers with actionable feedback to effectively assess aerosol transmission in medical settings and develop evidence-based intervention strategies.

This paper presents an approach to the elastic analysis of beams subjected to Saint-Venant torsion using Green’s theorem and the finite difference method (FDM). The Saint-Venant torsion of beams, also called free torsion or unrestrained torsion, is characterized by the absence of axial stresses due to torsion; only shear stresses are developed. A solution to this torsion problem consists of finding a stress function that satisfies the governing equation and the boundary conditions. The FDM is an approximate method for solving problems described with differential equations; it does not involve solving differential equations, equations are formulated with values at selected nodes of the structure. In this paper, the beam’s cross-section was discretized using a two-dimensional grid and additional nodes were introduced on the boundaries. The introduction of additional nodes allowed us to apply the governing equations at boundary nodes and satisfy the boundary conditions. Beams with solid sections as well as multiply connected cross-sections were analyzed using this model; shear stresses and localized stresses at reentrant corners, torsion constant, and warping displacements were determined. Furthermore, beams with thin-walled closed sections, single-cell or multiple-cell, were analyzed using the Prandtl stress function whereby a linear distribution of the shear stresses over the thickness was considered; closed-form solutions for shear stresses and torsion constant were derived. The results obtained in this study showed good agreement with the exact results for rectangular cross-sections, and the accuracy was increased through a grid refinement. For thin-walled closed sections, the shear stresses obtained at the centerline using the closed-form solutions were in agreement with the values using Bredt’s analysis but the maximal values in the cross-section, which did not necessarily occur at the position with the smallest thickness, were higher; in addition, the results using the closed-form solutions were in good agreement with those using FDM.