A Demand-side management technique are deployed along with battery energy-storage systems (BESSs) to lower the electricity cost by mitigating the peak load of a building. Most of the existing methods rely on manual operation of the BESS, or even an elaborate building energy-management system resorting to a deterministic method that is susceptible to unforeseen growth in demand. In this study we propose a real-time optimal operating strategy for BESS based on density demand forecast and stochastic optimization. This method takes into consideration uncertainties in demand when accounting for an optimal BESS schedule, making it robust compared to the deterministic case. The proposed method is verified and tested against existing algorithms. Data obtained from a real site in South Korea is used for verification and testing. The results show that the proposed method is effective, even for the cases where the forecasted demand deviates from the observed demand

In this study, Fe-based superconductors (SCs) are described with a model showing a novel attractive force. First, we describe this novel force using an analog from electromagnetism. From electromagnetism, it was found that this force is a Lorentz force in which two electrons orbit around a Fe-ion with the same velocity. Then, we consider a wave function of an electron. Consequently, due to the property of the proposed attractive force and the quantum-field Hamiltonian, we clarified that the Bardeen–Cooper–Schrieffer (BCS) ground state can be reused. Afterward, attractive force energy was calculated according to the presented model. In Fe-based SCs, a structure transition is essential. Considering that the derived attractive force energy is relatively large, we employ the expanded T_c-equation from the BCS theory that includes the structure transition effect and the derived attractive force energy. In addition, we succeed in analytically reproducing T_c-dome diagrams in various types of Fe-based SCs. Moreover, we discuss the universal property a general SC should have as well as the quantum critical point.

Fire is a significant threat to human life and civil infrastructures. Builders and architects are hankering for safer and sustainable alternatives of concrete that do not compromise with their design intent or fire safety requirements. The aim of the present work is to improve the residual compressive performance of concrete in the post-fire exposure, by incorporating by-products from urban residues. Based on sustainability and circular economy motivations, the attention is focused on rubber tire fly ash, aged brick powder, and plastic (PET) bottle residuals used as partial sand replacement. The selected by-products from urban residues are used for the preparation of Cement-Based Composites (CBCs) in two different proportions (10 % and 15 %). The thermal CBC behaviour is thus investigated under realistic fire scenarios (i.e., Direct Flame (DF) for 1 hour (1h)), by following the ISO 834 standard provisions, but necessarily resulting in non-uniform thermal exposure for the cubic specimens. The actual thermal exposure is further explored with a Finite Element (FE) model, giving evidence of thermal boundaries effects. The post-fire residual compressive strength of heated concrete and CBC samples is hence experimentally derived, and compared to unheated specimens in ambient conditions. From the experimental study, the enhanced post-fire performance of CBCs with PET bottle residual is generally found superior to other CBCs or concrete. The structure-property relation is also established, with the support of Scanning Electron Microscopy (SEM) micrographs. Based on existing empirical models of literature for the prediction of the compressive or residual compressive strength of standard concrete, newly developed empirical relations for both concrete and CBCs are assessed.

Abstract: Background: The diagnosis of nasal airway disorders relies on questionnaires, subjective data, and objective data. Interpretation of objective data obtained from measurement technology is not well understood by providers and researchers who use the equipment to test nasal airway function, justifying the need to cre-ate a new clinical tool. The Davidson Airway Function & Nasal Evaluation (DAFNE) Scoring System is a web-based scoring system that allows healthcare providers (MDs, PAs, PTs, APRNs, DMDs, DDSs, SLPs, and DCs) and researchers who treat nasal obstruction and breathing disorders to make more accurate diagnostic decisions, select the appropriate treatment for individualized patient care, monitor treatment progression and outcomes, and show how to approach a collaborative care model with other healthcare professionals. The current technologies, such as 4-phase rhinomanometry, use a simple approach that relies on a measurement tracing intersecting a color-coded y-axis on a four-quadrant graph with diagnostic numeric data output de-scribing nasal airflow and resistance. This is a good source of biofeedback demonstrating abnormal nasal breathing patterns but lacks interpretation guidelines to describe the severity of disease. The more sophisti-cated proprietary DAFNE approach uses multiple parameters which include airflow restriction, speed, vol-ume, and patient characteristics to identify patients’ disease progression much more accurately. Additionally, it explains how to segregate patients into appropriate treatment options which minimizes risks and compli-cations associated with sleep and breathing disorders while improving patient outcomes. Methods: Electronic searches of PubMed, MEDLINE, EMBASE Cochrane Library, and Scopus of publications between 1988-2022 were necessary to identify studies which determined the ranges of nasal function measurement parameters among three airway measurement technologies used in writing the DAFNE Score algorithm. The performance of DAFNE was evaluated compared to the research data and patient demographics used in previous studies. Results: By using primary outcome measurements from the literature, we were able to create a reliable, re-peatable, and validated tool to facilitate patient identification, treatment stratification, and collaboration for sleep and nasal breathing dysfunction. Subsequently, we found DAFNE could be used to identify the appro-priateness of a sleep study. Conclusions: DAFNE Scoring System has demonstrated the ability to detect high risk patients in the pediatric and adult populations susceptible of sleep apnea and breathing dysfunction needing a sleep study and treatment to improve nasal airway function and sleep. DAFNE Scoring System should be used as an adjunct tool in routine clinical practice and research to further understand the technol-ogy data output, identify patients at risk, stratify treatment options, progress, and stabilization after treatment, and how to collaborate with other healthcare providers to improve patient outcomes.

A steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings and multistory housing. To assess the seismic performance of buildings with steel damper columns, the peak displacement of the whole building and the energy dissipation demand of the dampers must be evaluated. This article proposes an energy-based prediction procedure for the peak and cumulative response of an RC frame building with steel damper columns. The proposed procedure considers two energy-related seismic intensity parameters, namely the maximum momentary input energy and the total input energy. The peak displacement is predicted considering the energy balance during a half cycle of the structural response, using the maximum momentary input energy. The energy dissipation demand of the dampers is then predicted considering the energy balance during a whole response cycle using the total input energy. The local responses (e.g., peak drift, maximum plastic rotation of beams, maximum shear strain, and energy dissipation demand of dampers) are predicted using pushover analysis. Numerical analysis results for 8- and 16-story RC buildings show that the proposed prediction method achieves satisfactory accuracy.

Background: The Davidson Airway Function & Nasal Evaluation (DAFNE) Scoring System was developed as an intuitive and research-based scoring system that could be validated through beta testing and easily introduced to healthcare providers of several subspecialties who treat nasal obstruction and breathing disorders (MDs, PAs, PTs, APRNs, DDSs, and DCs). This scoring system was shown to increase the knowledge of airway function, nasal measurement parameters, and identification of proper treatment options for sleep and breathing disorders. The basis for the DAFNE score was developed from a systematic review of nasal measurement data. Methods: Electronic searches of PubMed, MEDLINE, EMBASE Cochrane Library, and Scopus of publications between 1988-2022 were used to identify studies validating nasal function measurement parameters to create the algorithm for the DAFNE Score™. The systematic review was accomplished using the 2020 ‘Preferred Reporting Items for Systematic Reviews’ (PRISMA) guidelines. Results: Twenty studies met the inclusion criteria for systematic review. Primary outcomes measurements demonstrated reliability, repeatability and validity of the DAFNE measurement technologies, data and output. Conclusions: The data analysis and systematic review uncovered a need and framework to develop and validate a web-based software algorithm for global access to improve the understanding of data interpretation of nasal measurements from three nasal measurement technologies. DAFNE Scoring should be used as an adjunct tool in routine clinical practice and research to further understand the technology data output and how to collaborate with other healthcare providers to improve patient outcomes.

Ti-aluminosilicate gels were used as supports for immobilization of Fe, Co and Ni oxides (5%) by impregnation, and synthesis of efficient photocatalysts in degradation of β-lactam antibiotic from water. Titanium oxide (1 and 2%) was incorporated into zeolite network by modifying the gel during the zeolitation process. The formation of the zeolite Y structure and its microporous structure were evidenced by X-ray diffraction and N2 physisorption. The structure, composition, reduction and optical properties were studied by X-ray difraction, H2-TPR, XPS, Raman, photoluminiscence and UV-Vis spectroscopy. The obtained results indicated a zeolite Y structure for all photocatalysts with tetra-coordinate Ti4+ sites. The immobilized metals from group VIII are both in the form of metal oxides such as Fe2O3, Fe3O4, CoO, Co3O4 , NiO and also in the me-tallic state (Fe0, Co0, and Ni0). A red shift of the absorption edge was observed in UV-Vis spectra of photocatalysts upon addition of Fe, Co or Ni species. The photocatalytic performances were evaluated in degradation of cefuroxime from water under visible light irradiation. The best results were obtained for iron immobilized photocatalysts. Scavenger experiments explained the photocatalytic results and their mechanisms. A different contribution of the active species to the photocatalytic reactions was evidenced.

Video capsule endoscopy (VCE) is increasingly used to decrease the discomfort among patients owing to its small size. However, VCE has a major drawback of not having narrow band imaging (NBI) functionality. The current VCE has the traditional white light imaging (WLI) only, which has poor performance in the computer-aided detection (CAD) of different types of cancer compared with NBI. Specific cancers, such as esophageal cancer (EC), do not exhibit any early biomarkers, making their early detection difficult. In most cases, the symptoms are unnoticeable, and EC is diagnosed only in later stages, making its 5-year survival rate below 20% on an average. NBI filters provide particular wavelengths that increase the contrast and enhance certain features of the mucosa, thereby enabling early identification of EC. However, VCE does not have a slot for NBI functionality because its size cannot be increased. Hence, NBI image conversion from WLI can be achieved only in post-processing at present. In this study, a complete arithmetic assessment of the decorrelated color space was conducted to generate NBI images from WLI images for VCE of the esophagus. Three parameters, namely, structural similarity index metric (SSIM), entropy, and peak-signal-to-noise ratio (PSNR), were used to asses the simulated NBI images. Results show the good performance of the NBI image reproduction method, with SSIM, entropy difference, and PSNR values of 93.215%, 4.360, and 28.064 dB, respectively.

As on 31.03.2020, 55.4 % (205135 MW) of total installed capacity (370106 MW) in India is through coal and lignite based power plants. These plants, set up by central, state and private utilities with substantial capital investment are facing consistently reducing Plant Utilization Factor (known as Plant Load Factor, PLF, in India). In the year 2019-20 the national average thermal power PLF stood at 55.4%, down from 78.6 % in 2007-08. On the other hand, the electricity demand is consistently rising in the country and there exists a peak and energy shortage at national level. In 2019-20 energy shortage was 0.7 % and peak shortage was 0.5 %. A disturbing paradox therefore exists here. On one hand, the country is power deficit, and on the other hand, a large amount of coal based affordable power, ready to be generated by thermal power generators, remains grossly unused. Looking into the fact that considerable investment has gone into developing these thermal power generation assets in the country, the falling PLF is a matter of concern for all the key stakeholders including the power producers, lenders, regulators and consumers. This paper identifies seven major factors that are affecting PLF of thermal power plants and then makes an attempt to project future scenario of PLF so that critical stakeholders can intervene through appropriate actions. Primary research with responses from power professionals has been used to find out the major factors. Future projection of PLF has been done using Partial Least Square (PLS) regression. Projection shows that in the Business As Usual case (Factors increasing at the current CAGR rate), the thermal power plants will face very low level of PLF (14.76 %) by 2024-25. This will mean that many plants will be shut down and many will run for only few hours in a day that too at very low loads. If the future generation mix is kept as indicated by Central Electricity Authority (CEA), a Govt. of India in its report (Draft report on optimal generation capacity mix for 2029-30- CEA- Govt of India) then the thermal power plant average PLF can sustain above 68 % until 2024-25. If followed, this path can be a breather for the thermal power plants.

Noise reduction in medical images is a perplexing undertaking for the researchers in digital image processing. Noise generates maximum critical disturbances as well as touches the medical images quality, ultrasound images in the field of biomedical imaging. The image is normally considered as gathering of data and existence of noises degradation the image quality. It ought to be vital to reestablish the original image noises for accomplishing maximum data from images. Medical images are debased through noise through its transmission and procurement. Image with noise reduce the image contrast and resolution, thereby decreasing the diagnostic values of the medical image. This paper mainly focuses on Gaussian noise, Pepper noise, Uniform noise, Salt and Speckle noise. Different filtering techniques can be adapted for noise declining to improve the visual quality as well as reorganization of images. Here four types of noises have been undertaken and applied on medical images. Besides numerous filtering methods like Gaussian, median, mean and Weiner applied for noise reduction as well as estimate the performance of filter through the parameters like mean square error (MSE), peak signal to noise ratio (PSNR), Average difference value (AD) and Maximum difference value (MD) to diminish the noises without corrupting the medical image data.

The process of anaerobic digestion used for methane production can be enhanced by incorporating stimulating materials. The effects of these materials are dependent on various factors including the processed substrate, process conditions, and the type and amount of the stimulating material used. As part of the study, three different stimulating materials - iron powder, lime, and milled porous ceramic - were added to the 30-day anaerobic digestion of the brewer's spent grain to improve its performance. Different doses ranging from 0.2 to 2.3 gTS×L-1 were tested, and methane production kinetics were determined using the first-order model. The results showed that the methane yield ranged from 281.4±8.0 to 326.1±9.3 ml×gVS-1, while substrate biodegradation ranged from 56.0±1.6 to 68.1±0.7%. The addition of lime reduced methane yield at almost all doses by -6.7% to -3.3%, while the addition of iron powder increased methane yield from 0.8% to 9.8%. The addition of ceramic powder resulted in a methane yield change ranging from -2.6% to 4.6%. These findings suggest that the use of stimulating materials should be approached with caution, as even slight changes in the amount used can impact methane production.

The steel damper column is an energy-dissipating member that is suitable for reinforced concrete (RC) buildings, and those used for multistory housing in particular. However, the effectiveness of steel damper columns may be affected by the behavior of surrounding members, and this effect can be severe in the case of seismic sequences. This article investigates the nonlinear response of building models having an RC moment-resisting frame (MRF) with and without steel damper columns under seismic sequences. The applicability of the concept of the momentary energy input to the prediction of the peak response of RC MRFs with damper columns under seismic sequences is also investigated. The main findings of the study are summarized as follows. (1) The peak response of RC MRFs with damper columns subjected to sequential accelerations is similar to the peak response obtained considering only the mainshock, whereas the cumulative strain energy of RC MRFs accumulates more for sequential accelerations. (2) The steel damper column is effective in reducing the peak and cumulative responses of RC MRFs in the case of sequential seismic input. (3) The relation of the hysteretic dissipated energy during a half cycle of the structural response and the peak displacement of the first modal response can be properly evaluated using the simple model proposed in this study.

The traditional sequent peak algorithm (SPA) was used to assess the reservoir volume (VR) for comparison with deficit volume, DT, (subscript T representing the return period) obtained from the drought magnitude (DM) based method with draft level set at the mean annual flow on 15 rivers across Canada. At an annual scale, the SPA based estimates were found to be larger with an average of nearly 70% compared to DM based estimates. To ramp up DM based estimates to be in parity with SPA based values, the analysis was carried out through the counting and the analytical procedures involving only the annual SHI (standardized hydrological index, i.e. standardized values of annual flows) sequences. It was found that MA2 or MA3 (moving average of 2 or 3 consecutive values) of SHI sequences were required to match the counted values of DT to VR. Further, the inclusion of mean, as well as the variance of the drought intensity in the analytical procedure, with aforesaid smoothing led DT comparable to VR. The distinctive point in the DM based method is that no assumption is necessary such as the reservoir being full at the beginning of the analysis - as is the case with SPA.

The mixing of terrestrial groundwater and seawater creates dynamic reaction zones in intertidal areas, where land-derived Fe(II) is oxidized to Fe(III) and then precipitates as Fe hydroxides at groundwater-seawater interface. These hydrogeochemical processes contribute to the formation of iron curtains beneath soil surface, which in turn influences the evolution of coastal aquifers. This paper provides a comprehensive review of physical and geochemical processes at field scale in coastal areas, explores the impact of mineral precipitation on pore structure at pore scale, and synthesizes reactive transport modeling (RTM) approaches for illustrating continuum-scale soil physio-chemical parameters during the evolution of porous media. Upon this review, knowledge gaps and research needs are identified. Additionally, challenges and opportunities are presented. Therefore, the incorporation of observational data into a comprehensive physico-mathematical model becomes imperative for capturing the pore-scale processes in porous media and their influence on groundwater flow and solute transport at large scales. Furthermore, a synergistic approach integrating pore-scale modeling and non-invasive imaging can provide detailed insights into intricate fluid-pore-solid interactions for future studies, as well as facilitate the development of regional engineering-scale models and physio-chemical coupled models with diverse applications in submarine science and engineering.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

Formation of Fe- and Mg-rich smectite and zeolite under alkaline conditions is concerned as secondary minerals after alkaline alteration of bentonite in a repository of radioactive wastes. It might be crucial for safety assessment whether smectite will be formed or not as secondary minerals after alkaline alteration of bentonite. In present paper, Fe- and Mg-rich smectite which are currently interacting with hyperalkaline groundwater was found at Narra in Palawan, Philippines. Mineralogical and geochemical investigation was conducted to understand formation process of smectite and factors determined secondary mineral species. Our study revealed a certain amount of smectite may have been produced under hyperalkaline conditions, altered from amorphous or poorly crystalline material such as M-S-H and F-S-H. Key factor which decides smectite or zeolite as secondary minerals after alkaline alteration of bentonite might be whether nuclei of M-S-H and/or F-S-H will be formed or not. This might be decided by the presence of dissolved Mg2+ and Fe2+ in the system. Our suggested formation process of smectite under alkaline conditions is analogue with generally-accepted model of smectite formation that might have been occurred on early Mars.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

This study purposes the use of plug-in electric vehicles for demand side management (DSM) considering uncertainties in demand as well as uncertainties due to mobility of PEV to mitigate peak demand. The solution also seeks to reduce electric cost in addition to reducing the effects of greenhouse gases. In recent years DSM using distributed storage system such as battery energy management system (BESS) and plugged-in electric vehicles (PEV) have become very prevalent with most implementations resorting to deterministic load forecast. These methods do not consider the potential growth in demand making their solutions less robust. In this study we propose a real-time density demand forecast and stochastic optimization for robust operation of PEV for a building. This method accounts for demand uncertainties in addition to uncertainties in mobile energy storage as found in PEV, making the resulting solution robust as compared to the deterministic case. A case study on a real site in South Korea is used for verification and testing. The proposed study is verified and tested against existing algorithms. The result verifies the effectiveness of the proposed approach