This paper investigates the feasibility of a backend design for real-time, multiple-channel processing digital phased array system, particularly for high-performance embedded computing platforms constructed of using general purpose digital signal processors. Frist, we obtained the lab-scale backend performance benchmark from simulating beamforming, pulse compression, and Doppler filtering based on MicroTCA chassis using Serial RapidIO protocol in backplane communication. Next, a field-scale demonstrator of a multifunctional phased array radar is emulated by using the similar configuration. Interestingly, the performance of a barebone design is compared to that of emerging tools that systematically take advantage of parallelism and multicore capabilities, including Open Computing Language.

Based on a modified dice-and-fill technique, a PIN-PMN-PT single crystal 1-3 composite with the kerf of 12 μm and pitch of 50 μm was prepared. The as-made piezoelectric composite material behaved with high piezoelectric constant (d33 = 1500 pC/N), high electromechanical coefficient (kt = 0.81), and low acoustic impedance (16.2 Mrayls). Using lithography and flexible circuit method, a 48-element phased array was successfully fabricated from such a piezoelectric composite. The array element was measured to have a central frequency of 20 MHz and a fractional bandwidth of approximately 77% at −6 dB. Of particular significance was that this PIN-PMN-PT single crystal 1-3 composite-based phased array exhibits a superior insertion loss compared with PMN-PT single crystal and PZT-5H-based 20 MHz phased arrays. The focusing and steering capabilities of the obtained phased array were demonstrated theoretically and experimentally. These promising results indicate that the PIN-PMN-PT single crystal 1-3 composite-based high frequency phased array is a good candidate for ultrasound imaging applications.

The testing requirements of the active phased array antennas are very different from those of traditional passive antennas, due to its beam steering capability. Usually, each beam profile of the active phased array needs a separate radiation pattern test, which makes the overall testing time extremely long. Thus the traditional antenna test method can no longer meet the efficiency and cost requirements of new active phased array antennas test. In this paper, a fast test method tailored for phased array antennas is proposed that offers significantly reduced testing time at the expense of slight sacrifice of the accuracy. Using the simulated element pattern in array and ideal port excitation, the beam profile in any direction can be predicted by testing only a certain beam profile. Through theoretical derivation and experiments, the effectiveness of the method is verified, and the testing efficiency of the phased array antenna is demonstrated to be improved by ten times or even more.

In a software-defined radar (SDR) system, most of the signal processing usually implemented in hardware is implemented by software, thus allowing for higher flexibility and modularity compared to conventional radar systems. However, the majority of SDR demonstrators and proofs-of-concept reported in the open literature so far have been based on simple antenna systems. As a result, the full potentialities of an SDR approach have not been completely exploited yet. In this work, we propose a flexilbe antenna module to be integrated into an active electronically scanning array (AESA) with controlled sidelobe level over a wide angular range, exhibiting polarization reconfigurability with low cross-polarization level and high isolation. For this purpose, analytical and numerically efficient techniques for the synthesis of the aperture distribution and the correct evaluation of the radiating features (e.g., beamwidth, pointing angle, sidelobe levels, etc.) are presented in order to grant a real-time control of the digital beamforming network. A sub-array module demonstrator is fabricated and measured to corroborate the concept.

This review paper aims to understand the current processing plant maintenance systems and further identify on-stream phased array corrosion mapping (PACM) to reduce turnaround maintenance (TAM) activity during plant operations. Reducing the TAM duration and extending the TAM interval are common goals of most researchers. Thus, a detailed review was performed to understand the maintenance systems and the problems faced. Furthermore, a review of the current PACM application and the possibility of applying it during on-stream inspection was also per-formed. PACM has better detectability for localized corrosion, and the results can be obtained for a range of thicknesses, which is the main advantage of this method. The challenge is to apply it to a surface with high temperatures, owing to the greater probe contact and the limitation of ultrasonic properties. This literature review provides a more precise direction for future research to evaluate PACM on piping that can be utilized in inspection during plant operation at elevated temperatures. Detecting and monitoring corrosion growth without shutdown.

X-band dual-polarization phased array radar (XPAR-D) possesses high temporal-spatial resolutions and plays a significant role in detecting meso- and micro-scale convective systems. However, the precipitation attenuation it endures necessitates an effective correction method. This study selected radar data from XPAR-D at the peak of Maofeng Mountain in Guangzhou during May 16-17, 2020 from three precipitation stages after quality control. Attenuation coefficients are calculated for different precipitation types through scattering simulations of raindrop size distribution (RSD) data. Drawing upon this, an attenuation correction algorithm (MZH-KDP method) is proposed for radar reflectivity factor (ZH) according to different raindrop types, and is compared to the ZH-KDP method currently in use. The results indicate that the attenuation amount of XPAR-D echoes depends on the attenuation path and echo intensity. When the attenuation path is shorter and the echo intensity is weaker, the amount of attenuation and correction is smaller. Difficulties arise when there are noticeable deviations in such a situation, which are challenging to solve via attenuation correction methods. Longer attenuation paths and stronger echoes highlight the advantages of the MZH-KDP method, while the ZH-KDP method tends to overcorrect the bias. The MZH-KDP method outperforms the ZH-KDP method for different precipitation types. The superior correction capability of the MZH-KDP method provides a significant advantage in improving the performance of XPAR-D for the detection of extreme weather.

Due to the accelerated development of the offshore method of oil production in recent decades, especially in the Arctic region, the risks of crude oil pollution of the waters of the World Ocean are inevitably increasing. These oil spills during the exploitation of shelf deposits, transportation of oil from production sites and other anthropogenic impacts have a devastating impact on the marine biosphere, economy and life of coastal regions. For operative monitoring of water surface and fixation of oil spills it is necessary to use modern, effective and reliable methods, remote monitoring tools. One of such methods is radar. This article deals with increasing the efficiency of the radar method of water surface monitoring by means of constructive modification of the radar antenna array and changing the shape of the radio signal. As a result of the literature review, theoretical analysis of radar and conducted mathematical modeling it is substantiated the increase of radar monitoring efficiency by using phased active antenna array and construction of the cosecant-squared pattern diagram of the radio signal.

Detecting, tracking, and classifying unmanned aerial vehicles (UAVs) in a swarm presents significant challenges due to their small and diverse radar cross-sections, multiple flight altitudes, velocities, and close trajectories. To overcome these challenges, adjustments of the radar parameters and/or position of the radar (for airborne platforms) are often required during runtime. The runtime adjustments help to overcome the anomalies in the detection, tracking, and classification of UAVs. The runtime adjustments are performed either manually or through fixed algorithms, each of which can have its limitations for complex and dynamic scenarios. In this work, we propose the use of multi-agent reinforcement learning (RL) to carry out the runtime adjustment of the radar parameters and position of the radar platform. The radar used in our work is a multibeam multifunction phased array radar (MMPAR) placed onboard UAVs. The simulations show the cognitive adjustment of the MMPAR parameters and position of the airborne platform using RL helps to overcome anomalies in the detection, tracking, and classification of UAVs in a swarm. A comparison with other artificial intelligence (AI) algorithms shows that RL performs better due to runtime learning of the environment through rewards.

Leaky-wave antennas (LWAs) represent a recent class of radiating systems, first appeared in the second half of the past century. Initially treated with a certain dose of skepticism due to the apparent non-physical nature of supported wave solutions, LWAs have so far deeply evolved from the original configuration of slotted metallic lossy waveguide and adapted to a huge number of practical application fields, from microwave to millimeter waves and even up to the terahertz frequency range. Due to physics of relevant working principle, LWAs are often found in planar and low-profile configurations, being critically required in many cutting-edge applications, where device miniaturization, scaling and integration are required. Here we propose a review of some of the most recent and perspective array-fed 2-D LWAs, selecting two of most widespread categories in applications, Fabry–Perot Cavity Antennas (FPCAs) and Bull’s-Eye Antennas (BEAs), discussing and illustrating some advanced features recently proposed.

Petrochemical plants use on-stream inspection more often to detect and monitor the corrosion on the equipment and piping system. Compared to ultrasonic thickness gauging and pulse-echo A-scan, phased array corrosion mapping has better coverability and can scan a large area to detect general and localized corrosion. This paper's objective is to obtain documentary evidence on the accuracy of corrosion detection from 30°C to 250°C on A36 low-carbon steel by carrying out simulation experiments every 10°C steps. A minimum of three sets of phased array corrosion mapping data in each temperature were collected to study and evaluate the detectability. The data evidence could enhance the confidence level of the plant's end users to use the phased array mapping in the future during an inspection. The experiments were found to be insufficiently thorough despite addressing the initial concerns, leaving more area for discussion in further studies, such as expanding the investigation to thicker carbon steel, stainless steel, and wedge materials.

Phased injection of natural gas into internal combustion marine engines is a promising solution for optimizing performance and reducing harmful emissions, particularly unburned methane, a potent greenhouse gas. This innovative practice distinguishes itself from continuous injection because it allows for more precise control of the combustion process with only a slight increase in system complexity. By synchronizing the injection of natural gas with the intake and exhaust valve opening and closing times while also considering the gas path in the manifolds, methane release into the atmosphere is significantly reduced, making a substantial contribution to efforts to address climate change. Moreover, phased injection improves the efficiency of marine engines, resulting in reduced overall fuel consumption, lower fuel costs, and increased ship autonomy. This technology has been tested on a single-cylinder, large-bore, four-stroke research engine designed for marine applications, operating in dual-fuel mode with diesel and natural gas. Performance was compared with that of the conventional continuous feeding method. Evaluation of the effect on equivalent CO2 emissions indicates a potential reduction of up to approximately 20%. This reduction effectively brings greenhouse gas emissions below those of the diesel baseline case, especially when injection control is combined with supercharging control to optimize the air-fuel ratio.

The article presents an innovative method for synthesizing radiation patterns efficiently by 1 combining the Taguchi method and neural networks, while validating the results on a 10-element 2 antenna array. The Taguchi method aims to minimize product and process variability, while neural 3 networks are used to model the relationship between antenna design parameters and radiation 4 pattern characteristics. This approach utilizes Taguchi parameters as inputs for the neural network, 5 which is then trained on a dataset generated by the Taguchi method. After training, the network is 6 validated using a real 10-element antenna array. Analytical results demonstrate that this method 7 enables efficient synthesis of radiation patterns with a significant reduction in computation time 8 compared to traditional approaches. Furthermore, validation on the antenna array confirms the 9 accuracy and robustness of the approach, showing a high correlation between predicted performances 10 by the neural network model and actual measurements on the antenna array.In summary, our article 11 highlights that the combined use of the Taguchi method and neural networks, with validation on a 12 real antenna array, offers a promising approach for efficient synthesis of antenna radiation patterns. 13 This approach combines speed, accuracy, and reliability in antenna system design.

Background: Slash pine (Pinus elliottii) is an important timber species in southern China, having been introduced from North America over a century ago. Recently, dozens of improved slash pine varieties have been authorized. However, the absence of efficient molecular markers hinders the identification of these improved varieties. In this study, we aimed to construct a set of DNA fingerprinting based on SNP markers for improved slash pine varieties and provide a technical procedure for their identification. Results: The genotypes of 29 improved slash pine varieties were captured using 51K liquid-phase probes developed by our team, resulting in the genotyping of 560,567 SNPs through next-generation sequencing. A total of 3502 SNPs were retained after screening for minor allele frequency, missing rate, heterozygosity rate, and other parameters. Subsequently, a random forest model was used to reduce the number of SNPs to 50. The identification rate of improved varieties with these 50 SNPs achieved 98.64%. We concluded that these SNPs effectively distinguish the improved varieties, which enabled the construction of DNA fingerprints for the improved slash pine varieties. Conclusions: This study provides a technical procedure for identifying improved slash pine varieties based on the Random Forest model and constructs a DNA fingerprinting of the 29 slash pine varieties using 50 SNPs.

The contactless coalescence of a droplet is of paramount importance for physical and industrial applications. This paper describes a coalescence method in mid-air via acoustic levitation using an ultrasonic phased array system. Acoustic levitation using ultrasonic phased arrays provides promising lab-on-a-drop applications, such as transportation, coalescence, mixing, separation, evaporation, and extraction in a continuous operation. The mechanism of droplet coalescence in mid-air may be better understood by experimentally and numerically exploring the droplet dynamics immediately before the coalescence. In this study, water droplets were experimentally levitated, transported, and coalesced by controlling acoustic fields. We observed that the edge of droplets deformed and attracted each other immediately before the coalescence. Through image processing, the radii of curvature of the droplets were quantified and the pressure difference between the inside and outside the droplet was simulated to obtain the pressure and velocity information on the droplet surface. The results revealed that the sound pressure acting on the droplet clearly decreased before the impact of the droplets. This pressure on the droplets was quantitatively analyzed from the experimental data. Our experimental and numerical results provide deeper physical insights into contactless droplet manipulation for futuristic lab-on-a-drop applications.

Wavelength selective switches (WSSs) are essential elements for wavelength division multiplexing (WDM) optical networks, as they offer cost-effective, high port-count and flexible spectral channel switching. This work proposes a new hybrid WSS architecture that leverages the beam shaping and steering features of uniform silicon nitride (SiN) based end-fire optical phased arrays (OPAs). By introducing beamforming to a WSS system, the spectral channels on the liquid crystal on silicon (LCoS) panel can be tailored and arranged properly, depending on the optical configuration, using the beam control capabilities of OPAs. Combining 3D-FDTD and ray tracing simulations, the study shows that by reducing the input beam dimensions with proper sizing of the OPAs, the WSS design with the null-steering OPAs layout and 4×No switch size features increased spectral resolution. This extensive beamforming study on the steering-enabled layout reveals the acquirement of an even higher input channel number, achieving up to the 8×No WSS scheme with flexible channel routing on the LCoS panel. Such implementation of beamsteerers can unlock an extra degree of freedom for the switching capabilities of hybrid WSS devices. The results show great promise for the introduction of OPAs in WSS systems and provide valuable insight for the design of future wireless communication links and WDM systems.

A novel quasi-twisted miniaturized wideband Branch Line Coupler (BLC) is proposed. The design is based on bisecting the conventional microstrip line BLC transversely and folding bisected sections on double-layered substrates with a common ground plane in between. The pair of quarter wavelength horizontal parallel arms is converted to a Z-shape meandered microstrip line in the designed structure. On the other hand, the pair of quarter wavelength vertical arms are cut by half into two lines and converted to a periodically loaded slow wave structure. The bisected parts of BLC are placed on the opposite side of the doubled-layer substrate and connected through four vias passing through the common ground plane. This technique enabled a compact BLC size of 6.4×18 mm2, which corresponds to a surface area miniaturization by ~50% as compared to the classical BLC size of 10×23 mm2 at 6GHz, Moreover, the attained relative bandwidth is 73.9% (4.6-10 GHz) for S11, and 75.8% (4.5-10 GHz) for S33 as compared to 41% for the ordinary BLC at the same resonant frequency. The circuit is constructed on a double-layered low-cost FR4 substrate with a relative permittivity of 4.3, and a loss tangent of 0.025. An isolation of -13dB was realized in both S13 and S31 demonstrating an excellent performance. The transmission coefficients between input/output ports S21, S41, S23, and S43 are between -3.1dB to -3.5dB at the frequency of 6GHz. Finally, the proposed BLC provides phase differences between output ports of 90.5o and 94.8o at the frequency of 6GHz when the input ports 1 and 3 are excited, respectively. The presented design offers the potential of being utilized as a unit cell for building a Butler-matrix (BM) for sub-6GHz 5G beamforming networks.

Geometrical assessments of human skull have been done based on the anatomical landmarks. Automatic detection of the landmarks, if developed, will be a great help not only medically, but also anthropologically. An automated system with multi-phased deep learning networks to predict three-dimensional coordinate values of cranio-facial landmarks, was developed. From a publicly available database, computed tomography images of craniofacial area were obtained. They were digitally reconstructed into three-dimensional models. Sixteen anatomical landmarks were plotted on each of the models and coordinate values of them were recorded. Three-phased regression deep learning networks were trained respectively with 90 training datasets. For evaluation, 30 testing datasets were employed. Three-dimensional error for the first phase, testing 30 data, was 11.60 pixels in average. (1 pixel = 500 / 512 mm) For the second phase, it was significantly improved to 4.66 pixels. For the third phase, it was significantly progressed to 2.88. This was comparable to the gaps between the landmarks, plotted by two experienced practitioners. Our proposing method of multi-phased prediction, coarse detection first and narrowing down the detection area, may be a possible solution, within the physical limitation of memory and computation.

Wireless power transfer promises to revolutionize the way we use and power mobile devices. However, low transfer efficiencies prevent this technology from seeing wide scale real-world adoption. The aim of this work is to use quasioptics to develop a system composed of a dielectric lens fed by a phased array to reduce spillover losses, increasing the beam efficiency, while working on the antenna system’s Fresnel zone. The DC-RF electronics, digital beamforming and beam-steering by an FPGA, and radiating 4x4 microstrip patch phased array have been developed and experimented upon, while the lens has been designed and simulated. This paper details these preliminary results, where the phased array radiation pattern was measured, showing that the beam is being generated and steered as expected, prompting the lens construction for the complete system experimentation.

This paper presents a demonstration of a linearly-polarized transmit-arrays antenna with high-efficiency and wideband operating in X-band. The topology of the unit cell consists of two identical patch antennas loaded by C-loop slot and interconnected by a metalized via through a ground plane sandwiched between two identical substrates [18]. A waveguide measurement system WGMS has been used for single cell characterization (reflection/transmission coefficients). Good results have been demonstrated in terms of matching performances; the reflection coefficient S11 is under 10-dB in the 9.4-10.4 GHz band (i.e. 10.1% around 9.9 GHz) and with only 0.35 dB-insertion loss at 10 GHz. The transmit-arrays prototype permitted to achieve 22.4 dBi of directivity and 20.1 dBi of gain. The aperture and radiation efficiencies are about 28.2% and 58.3%, respectively. With a focal ratio (F/D) of 1/2 the spill-over loss is less than 2 dB. Beam-scanning up to ± 35° has been achieved with the same phase quantization (passive) and less than 3 dB of gain losses.

This paper presents an extensive performance analysis of open-ended waveguide elements for direct radiating arrays with high scan angle (± 50º/60º). The evaluated designs are based on square and hexagonal apertures loaded with ridges. Both square and triangular lattices are considered in the framework of Ka-band downlink design requirements for future LEO mega-constellations. The parameter space defined by the monomodal condition has been explored to find an optimum value for each structure. The analyses are validated with both infinite and finite full-wave models in terms of active reflection coefficient, scan loss and cross-polar discrimination.