Due to growing concerns about environmental pollution from plastic waste, plastic recycling research is gaining momentum. Traditional methods, such as incorporating inorganic particles, increasing cross-linking density with peroxides, and blending with silicone monomers, often improve mechanical properties but reduce flexibility for specific performance requirements. This study focuses on synthesizing silica nanoparticles with vinyl functional groups and evaluating their mechanical performance when used in recycled plastics. Silica precursors, namely sodium silicate, and vinyltrimethoxysilane (VTMS), combined with a surfactant, were employed to create pores, increasing silica's surface area. Early-stage introduction of vinyl functional groups prevented the typical post-synthesis reduction in surface area. Porous silica was produced in varying quantities of VTMS, and the synthesized porous silica nanomaterials were incorporated into recycled Polyethylene to induce cross-linking. Despite a decrease in surface area with increasing VTMS content, a significant surface area of 883 m2/g was achieved. In conclusion, porous silica with the right amount of vinyl content exhibited improved mechanical performance, including increased tensile strength, compared to conventional porous silica. This study shows that synthesized porous silica with integrated vinyl functional groups effectively enhances the performance of recycled plastics.

This paper studies the dynamic response of corner supported modular steel buildings with a core wall system, under progressive collapse scenarios, associated with corner module removals. Since using secondary systems such as concrete core in mid- to high-rise buildings is currently una-voidable, understanding their impact on load transfer between modules during collapse scenarios becomes essential. The designated buildings with four-, eight- and twelve-story were modelled using the macro-model based finite element method in Abaqus. Also, three different locations are considered for the concrete shear core within the building plan, leading to nine various case scenarios. Each vertical and horizontal inter-module connection was modelled by one axial and two shear springs with predefined nonlinear force-displacement behaviour. The local and global buckling, which plays an essential role in the building's stability, was considered to obtain accurate results. Finally, parametric studies on the building response were carried out, including the intra-module connection rigidity and inter-module connection stiffness. The results demonstrated that the core wall could maintain the robustness of modular steel building through two mechanisms dependent on its location within the plan. Also, preventing plastic hinges from forming in beams could be introduced as an anti-collapse mechanism in the corner module removal scenarios

With the escalating water scarcity in agriculture, a novel water-saving technique has emerged: drip irrigation with plastic-film mulch (DI). Root function is crucial for sustaining rice production, and understanding its response to DI is essential. However, few studies have evaluated root systems in rice varietals and examined which kind of root system contributes to improving rice grain yield and water productivity in DI. To fill this knowledge gap, we conducted a two-year field experiment comparing two irrigation systems: continuous flooding (CF) and DI. We analyzed their effectiveness with four rice varieties, including upland, F1 lowland, animal feed lowland, and lowland varieties. Vertical root distribution, root bleed-ing rate, photosynthetic-associated parameters, water productivity, and yield performance were analyzed. In our study, the average grain yield of varieties in the DI system (6.4t/ha) was equivalent to those in the CF system (6.6 t/ha). Compared to CF, DI demonstrated significant water-saving potential, saving approximately 35% of the total water supplied, resulting in higher water productivity. Among the varieties, the deep-root weight of the upland variety significantly increased by 51%. The deep-root ratio was positively correlated to transpiration rate, grain yield, and water productivity, which suggested that it contributed to high transpiration, thus maintaining a high carbon assimilation rate resulting in high yield and water productivity. Therefore, deep roots deserve consideration as a trait potentially corresponding to high yield under DI.

The paper presents the basic structural parts, a 3D model and the overall design of a laboratory machine, which was created to detect vibrations generated by the casing of a conveyor roller ro-tating at different speeds. The intention of the authors was to verify whether plastic brackets in-serted into the structurally modified trestles of a fixed conveyor idler can reduce the vibration values transmitted from the rotating conveyor roller to the trestle of a fixed idler. Experimental vibration measurements taken on the non-rotating parts of conveyor rollers, performed on a laboratory machine according to ISO 10816, are suitable for characterizing their operating condi-tions with regard to trouble-free operation. The aim of this paper is to detect the vibrations of a rotating conveyor roller on a laboratory machine in the defined places of a fixed conveyor idler and also on the steel frame of a laboratory machine that represents the supporting track of a belt conveyor. Vibrations detected by piezoelectric acceleration sensors were recorded by a measur-ing apparatus and displayed in the environment of Dewesoft X software. The measurements show that the vibration values grow with the increasing speed of the conveyor roller rotation. Experimental measurements have proven the correctness of the assumption that the vibrations transmitted to the trestle of a fixed conveyor idler are lower by up to 40% when using plastic brackets into which the axle of the conveyor roller is attached, compared to the solution where the axle of the conveyor roller is inserted into the notches of a steel trestle.

This study investigates the spatial and temporal distribution of litter at 7 beach sectors in Cadiz Bay, Southwest Spain. Two ten-day surveys carried out in autumn 2022 and spring 2023 revealed a total of 4,199 and 4,634 items, respectively, with plastic being the predominant material (71.13% in autumn, 88.39% in spring). Litter quantities varied significantly among beaches, La Puntilla showing the highest abundance with 0.48 ± 0.25 items m-1 in autumn and 1.34 ± 0.61 items m-1 in spring. The lowest abundance was recorded at sector 1 of Valdelagrana beach (0.08 ± 0.06 items m-1) during autumn and at El Castillito beach (0.08 ± 0.04 items m-1) during spring. Statistical analyses did not reveal significant differences in litter quantities between autumn and spring, however high significant interaction was shown considering both season and beach lo-cation. Seasonal differences were also observed in litter composition. Litter categories increased from 90 in autumn to 107 in spring. The top 10 litter categories varied between seasons and included cigarette butts, plastic fragments and plastic packaging. Cigarette butts were principally abundant in autumn because re-lated to summer beach users and wet wipes were particularly observed in spring because linked to wastewaters and river discharges especially relevant in winter months. Hydrodynamic and wind conditions were analyzed, revealing complex relationships with litter abundance.

The use of plastic in agriculture has become so omnipresent within the industry that it has acquired it own lexicon to become known as ‘plasticulture’. However, since, compared to other industries the quantities consumed are low, little attention is granted to this waste stream. This is the case both with local and international policies even though it bears a close connection to soil health and therefore is a prerequisite to improve the sustainability of food production processes including food security. Using Malta as a case study, the research utilises quantitative and qualitative tools to identify and quantify the most common types of agricultural plastic waste generated and determines the attitudes of farmers towards a collection and recycling scheme. While it identifies that incineration and ploughing of plastic waste as regular practices, it also ascertains the willingness of farmers to acquire more knowledge about more appropriate methods to dispose of this waste stream thus guiding policy makers towards the need to initiate educational measures for farmers to prevent these harmful practices. Through stakeholder interviews the research highlights that the present lack of data is a major hindrance for policy to take account of this waste stream.

The spring-in phenomenon of the composite parts can affect the assembly process. This study aims to predict the spring-in phenomenon of carbon fiber reinforced plastic (CFRP) part. Here, we predict the spring-in of the CFRP part using a coupled analysis of the forming and cooling processes during the stamping process. First, a simulation of the entire forming process, such as the transfer of the composite laminate, gravity analysis, and forming was performed to obtain the temperature distribution of the CFRP part. Subsequently, a finite-element (FE) simulation of the cooling process was conducted to predict the spring-in phenomenon of the shaped CFRP part using the temperature data obtained in the forming simulation. Finally, a CFRP part was manufactured and compared with the results of the FE simulation.

Co-Zr amorphous alloys exhibit soft magnetic properties, whereas Co-rich crystalline magnetic phases in this alloy system display hard magnetic behaviour. In this study, an initial two-phase Co-Zr composite with an overall composition of 75 at.% Co and 25 at.% Zr was processed by high pressure torsion (HPT) and the effects of severe plastic deformation and subsequent thermal treatment on the structural evolution and its magnetic properties have been investigated. HPT processing allowed us to achieve an amorphous microstructure in the as-deformed state with low coercivity. To further tune magnetic properties and study the alloys’ crystallization behaviour, various annealed states are investigated. Microstructural properties are correlated to the magnetic properties and a decreasing coercivity with increasing annealing temperature is observed despite the onset of crystallization in the amorphous alloy. At higher annealing temperatures, coercivity increases again. The results appear promising to obtain tuneable rare-earth free magnetic materials by severe plastic deformation.

The effectiveness of a recently proposed methodology in the identification of damage in planar, multi-storey, Reinforced Concrete (RC) moment-frames, which develop a plastic-yield mechanism on their beams, is showcased here via the examining of a group of such existing multi-storey frames with three or more unequal spans. According to the methodology, the diagram of the instantaneous Eigen-Frequencies of the frame in the nonlinear regime is drawn as a function of the inelastic seismic roof displacement by performing a sequence of pushover and instantaneous modal analyses with gradually increasing target displacement. Using this key-diagram, the locations of severe seismic damage in an existing moment-frame can be evaluated if the instantaneous fundamental eigen-frequency of the damaged frame, at an analysis step within the nonlinear area, is known in advance by “the monitoring and the identification of frequencies” using a local network of uniaxial accelerometers. This is a hybrid technique because both procedures, the instrumental Monitoring of the structure and the Pushover analysis on the frame (M and P technique), are combined. Moreover, the damage image of the planar multi-storey moment-frame is illustrated, and the lateral stiffness matrix of the damaged frame is calculated with high accuracy.

Keywords: Fatigue crack propagation; Welding residual stress; Plastic re-distribution; Stress ratio effect

Every year since the last fifty years, the world is waking up to higher and higher average temperature of the earth. Initially it was thought that this trend is a part of cyclical warming and cooling of the earth and nothing to be much worried about. However, with weather conditions become erratic and unusual over a large swath of the planet more and more frequently and regularly, scientists started to speak of Climate Change and people started to listen. In this paper we briefly discuss the link between global warming, climate change and current policies in the developing world to drive home the urgent need for alternative thinking. We briefly discuss the theoretical link between economic development and greenhouse gas emission and lay the micro foundation of the Environmental Kuznets Curve (EKC) before providing some evidence of global climate change and why this is a matter of concern for social scientists. Then we explore two avenues through which human activities are aggravating the situation especially in developing countries – the role of business architecture and the role of built architecture. We argue that these twin architecture are aggravating global warming by moving away from sustainable development policies.

The strength of laser joined metal and plastic hybrids is based purely on adhesion. Unpolar plastics like polypropylene depend solely on the mechanical adhesion while polar plastics like polyamide 6.6 develop covalent bonds with the metal. In this research the influence of different surface metallizations on the lap shear strength of laser joined hybrids was investigated. Sandblasted AISI 304 was used as base metal and reference. Aluminum and titanium coatings were deposited by the means of Arc-PVD. Polypropylene and polyamide 6.6 were utilized as polar und unpolar plastics. The lap shear strength of all hybrids with polyamide 6.6 was higher than the polypropylene samples. For all investigated variations of the laser power, scanning speed and the cohesive and adhesive failure modes, the samples joined with the sandblasted AISI 304 showed the highest lap shear strength. The reduction in lap shear strength for the coated samples was due to the increased difference in thermal conductivity between the plastics and the coating materials. This lead to increased warping and residual stresses. It can be concluded that the thermal properties of the metallization in laser joined metal and plastic hybrids has a high impact on the lap shear strength.

Plastic waste accumulation poses significant environmental challenges, underscoring the importance of closing the plastic life cycle by converting waste into valuable products. Pyrolytic char, a promising byproduct, offers diverse industrial applications. However, little attention has been given to converting hydrocarbon-based plastics into solid carbon due to their low fixed carbon content. This study compares sulfonation and thermal oxidation stabilization techniques for carbonizing waste polyethylene and polyvinyl chloride. Results indicate sulfonation yields higher pyrolytic char formation and improves surface properties, surpassing Al2O3 in catalyst support characteristics. Thermal oxidation increases fixed carbon content but adversely affects char yield and surface properties. Both methods effectively enhance fixed carbon content, but sulfonation emerges as more advantageous, suggesting potential use of plastic-derived char as a catalyst support material, contributing to circular economy development.

Plastic contamination of small dimensions (

Monitoring and maintenance of cracked structures are generally done using structural integrity assessments. The plastic zone (PZ) crack path (CP) criteria state that a crack grows in the direction when the radius of the plastic zone ahead of the crack tip reaches a minimum value. The PZ can be evaluated using Stress intensity factors (SIF). The SIFs under mixed-mode loading were extracted from literature from three samples: two SENT samples made from polycarbonate and one modified C(T) sample made from low-carbon steel. In addition, the CP angle was evaluated for the W and R-criteria. It was found that both can predict the CP for lateral cracks in both tested materials and monotonic and cyclic load when the mode-mixity does not change considerably from one crack length to the next one or goes beyond 0.2. Moreover, the R-criterion exhibited an error as high as 1.7%, whereas the W-criterion showed a 6% error on the last crack length for the low carbon steel sample under cyclic load, which had a 100% increase in mode-mixity. Finally, the applicability of LEFM is checked, while the CP is sought by finding the size of the PZ.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

This paper investigates if the polar groups induced by a plasma treatment can increase the lap shear strength of laser joined metal and plastic hybrids. Optimal laser joining parameters for cold-rolled AISI304 – Polyamide 6.6 and sandblasted AISI304 - Polypropylene hybrids are developed. The OWRK-method was utilized to identify the change in surface free energy of a low-pressure plasma treatment. Plasma treated samples were joined and tested. The fractured surfaces were investigated via light microscopy and SEM. The arithmetic means of the plasma treated hybrids lap shear strength with polyamide 6.6 varied slightly but all measured values were within the range of the untreated samples. The lap shear strengths of the polypropylene hybrids were significantly reduced. This was attributed to an overaging and the development of low molecular weight oxidized materials which lead to a weak boundary layer. No correlation between surface free energy and the lap shear strength could be found.

The seismic damage in reinforced concrete bridges is identified in this study using the "M and P" hybrid technique initially developed for planar frames. The proposed methodology involves a series of pushover and instantaneous modal analyses with a progressively increasing target deck displacement along the longitudinal direction of the bridge. From the results of these analyses, the diagram of the instantaneous eigenfrequency of the bridge, ranging from the health state to near collapse, is plotted against the inelastic seismic deck displacement. By pre-determining the eigen-frequency of an existing bridge along its longitudinal direction through "monitoring and frequency identification", the target deck displacement corresponding to the damage state can directly be found from this diagram. Subsequently, the damage can be identified by examining the results of the pushover analysis at the step where the target deck displacement is indicated. The effectiveness of this proposed technique is evaluated in the context of multiple span bridges with unequal pier heights, illustrated through an example of a four-span bridge. The findings demonstrate that the damage potential in bridge piers can be successfully identified by combining the results of a monitoring process and pushover analysis.

PVC-based materials are bad in terms of biodegradability. To enhance the ecological property of such materials, the fabrication of PVC-based composites using biofillers with acceptable performance characteristics could be considered. In this work, plant-filled PVC-based composite materials were obtained and study their optical, structural, thermal, and mechanical properties depending on the nature of the filler (spruce flour, birch flour, and rice husk) were studied. Increasing the proportion of plant filler somewhat reduces the strength characteristics and reduces the flexibility of the samples. But samples with plant filler allows them to be used at low temperatures without changing the operating characteristics. Some of the fillers affected the thermal stability of composites by increasing their thermal decomposition resistance. So, results have shown that plant-filled polymer composites based on PVC can be used on an equal basis with unfilled PVC plastic compound for some applications such as construction.

Effects of plastic deformation on the indentation feature of hot-rolled commercial pure titanium alloy were detected using microindentation. It was found that the most deformed sample experienced the largest indentation resistance and had the maximum dislocation density and the indentation size influenced the CP-Ti indentation feature. The Vicker hardness and energy dissipated demonstrated the significant influence of the dislocation motion and size effects on the indentation in the indentation deformation. The linear relation of the energy ratio which is related to the microstructures and the indentation depth ratio was obtained for hcp materials Titanium alloys.

The present article investigates the threshold analysis of yielding in a variable thickness rotating disk based on the Tresca criterion. The analysis is conducted on a Functionally Graded Material (FGM) constructed from tailored materials, following the theory of small deformations and for the case of plane stress. The elasticity modulus, density, and yield stress are assumed to be power functions of the radial coordinate. Poisson’s ratio is considered constant due to small variations in different materials. Additionally, the governing equation for the rotating disk is solved analytically. Besides the material type, another factor affecting the distribution of effective stress magnitudes is the cross-sectional shape (profile) of the disk. The thickness of the cross-sectional disk varies radially as a power function. In the current analysis, different conditions for the onset of yielding and the evolution of plastic flow are considered. For evaluation and validation, the obtained results are compared and validated against similar results for specific cases (homogeneous disk and constant thickness graded disk) available in previous references. The results indicate that considering variable thickness for the disk section significantly affects the stresses and the location of the initiation of yielding

Nanoindentation load-depth (P-h) plots is the basis for determination of mechanical properties of the samples and is especially vital for thin coatings deposited on substrates of various mechanical makeup from amorphous-brittle (borosilicate glass) to Silicon (having different crystallographic texture) to ductile substrates like stainless steel as well other aspects like indenter tip shape. The elastic-plastic response by simulated P-h plots as per modified empirical relations have been presented. The outcomes of this computational studies enlighten the database on the P-h plots for various coating/substrate systems and shall aid in the analysis of experimental P-h plots obtained,

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

Calcium sulphate (CS) is currently used as a bioabsorbable, completely synthetic and sterile material in the management of infected tissues and dead spaces (DS) mainly resulting from surgical procedures. Residual DS in the postoperative, may create an environment where hematomas fill up and bacteria can proliferate, leading to a high incidence of postoperative infections. Considering the available reviews in the literature, CS has been mainly studied in orthopedic surgery mostly giving brilliant results and low complication rates. Nowadays, orthopedists avail it in the form of pearls both as a bone void filler and as an “off-label” delivery agent for antibiotics in arthroplasty, chronic osteomyelitis and open fractures, paving the way of its application in many other contexts given its natural dis-position to biodegradation. In the last years, CS beads have been gaining ground in the general, vascular and endocrinological surgical specialties. Despite its clear potential and the increasing number of scientific evidences on the safety and effectiveness of CS application in the prophylaxis and treatment of infections, there are not many studies reporting on its application in fields other than orthopedics, with a substantial paucity in plastic and reconstructive surgery literature. This is some-how surprising, since reconstructive surgery often deals with complex wounds secondary to bone and soft tissue exposure, suture dehiscence, trauma, and surgical site infections. As far as we know this is the first updated systematic review assessing the state of the art, indications and new perspectives on the application of CS beads in plastic and reconstructive surgery.