Additive manufacturing (AM) of high strength Al alloys promises to enhance the performance of critical components related to various aerospace and automotive applications. The key advantage of AM is its ability to generate lightweight, robust, and complex shapes. However, the characteristics of the as-built parts may represent an obstacle to satisfy the part quality requirements. The current study investigates the influence of selective laser melting (SLM) process parameters on the quality of parts fabricated from different Al alloys. A design of experiment (DOE) is used to analyze relative density, porosity, surface roughness, and dimensional accuracy according to the interaction effect between the SLM process parameters. The results show a range of energy densities and SLM process parameters for the AlSi10Mg and Al6061 alloys needed to achieve “optimum” values for each performance characteristic. A process map is developed for each material by combining the optimized range of SLM process parameters for each characteristic to ensure good quality of the as-built parts. The second part of this study investigates the effect of SLM process parameters on the microstructure and mechanical properties of the same Al alloys. This comprehensive study is also aimed at reducing the amount of post-processing needed.

The Selective Paste Intrusion (SPI) method is a layer-by-layer additive manufacturing technique that allows for the production of complex geometries in concrete elements by selectively bonding aggregates with cement paste in a particle bed. To create reinforced concrete, the Wire and Arc Additive Manufacturing (WAAM) process shall be integrated into SPI. This technique allows the production of almost free-formed reinforcement and thus complements the advantage of SPI to produce free-formed structures of almost any geometry. However, integration of WAAM into SPI poses a considerable challenge, as high temperatures are generated during the welding process. These temperatures can negatively affect the rheological properties of the cement paste, in turn the penetration behavior of the paste in the particle bed and, subsequently, the mechanical properties of the hardened concrete. A possible passive cooling strategy is to increase the protruding length of the reinforcement bars out of the particle-bed. This requires that the distance of the print nozzle to the particle bed is as well increased, since it must be possible to move it across the reinforcement. The objective was thus to investigate the effect of that distance on print quality and to quantify a maximum allowable distance for an adequate print quality (for the printer setting used) in terms of shape accuracy and concrete strength. Compressive and flexural strength tests as well as geometrical measurements using a 3D scanning method were performed on specimen, printed with varying print nozzle to particle bed distances. It can be stated that for the used SPI print-heads, nozzle-types and parameter settings, the distance between the nozzle and the particle bed should not exceed 50 mm to ensure sufficient print quality in both shape accuracy and mechanical strength.

Among solar thermal collectors, the evacuated flat panel is emerging as a reference technology for operation at higher temperatures of up to 200 °C with an increased annual energy production owing to both direct and diffuse light capture. Accurate measurements of the optical properties of the selective absorbers used in such devices are key for a reliable estimation of the overall performance. These optical properties must be measured under high vacuum at high temperatures, conditions under which the panels are meant to operate. In this study, we accurately measured these properties using a calorimetric technique. The measurement procedure is based on a power balance equation for a flat sample suspended in a high-vacuum chamber with minimal thermal losses and is well adapted for this class of devices. Calorimetric measurements obtained under Sun and LED light revealed excellent reproducibility and good agreement with those obtained using traditional optical analysis at low temperatures in air. When extended up to the absorber stagnation temperature, which often exceeds 300 °C, the calorimetric measurements started to deviate from the optical measurements, indicating the importance of measuring under the operating conditions.

An ultraviolet (UV) nanosecond pulsed laser with a wavelength of 355 nm was applied to anneal amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFT) at various laser beam powers ranging from 0 to 280 mW. Laser irradiation was selectively carried out on the a-IGZO channel area using the beam scanning method after the a-IGZO TFT was formed through indium-tin oxide (ITO) electrode patterning and a subsequent lift-off process. After laser annealing, negative shifts in the threshold voltages and enhanced on-currents were observed at laser-beam powers ranging from 54 to 120 mW. No meaningful parameters were investigated for laser beams higher than 200 mW. By extracting the energy band gap and work function of a-IGZO from the transmittance and ultraviolet photoelectron spectroscopy (UPS) results, the ITO electrode/a-IGZO channel energy band structures were established under different laser annealing conditions, and the electron injection mechanism from the ITO to the a-IGZO channel was analyzed and optimized at a laser beam power of 120 mW. The results show that the electrical characteristics of the a-IGZO TFTs can be improved without any heat damage to the substrate because of the selective annealing process.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

A hemispheric asymmetry is known for the processing of global vs. local visual information. In this study, we investigated the existence of a hemispheric asymmetry for visual processing of low vs. high spatial frequency gratings. Event-related potentials were recorded in a group of healthy right-handed volunteers from 30 scalp sites. Six types of stimuli (1.5, 3 and 6 c/deg gratings) were randomly flashed 180 times in the left and right upper hemi-fields. Stimulus duration was 80 ms and ISI ranged between 850-1000 ms. Participants had to pay attention and respond to targets based on their spatial frequency and location, or to passively look at the stimuli. C1 and P1 visual responses, as well as a later Selection negativity and a P300 components of ERPs were quantified and subjected to repeated-measure ANOVAs. Overall, performance was faster for the RVF, thus suggesting a left hemispheric advantage for attentional selection of local elements. Similarly, the analysis of mean area amplitude of C1 (60-110 ms) sensory response showed a stronger attentional effect (F+L+ vs. F-L+) at left occipital areas, thus suggesting the sensory nature of this hemispheric asymmetry.

Aiming at the industrial scale development of a Scandium (Sc)-selective leaching process of Bauxite Residue (BR), a sufficiently numerous set of process design aspects has been investigated, by appropriate exploitation of available experimental data. The interpretation of experimental data for Sc leaching yield, with sulfuric acid as the leaching solvent, has shown significant impact from acid feed concentration, mixing residence time, liquid to solids ratio, and times of leachate re-usage onto fresh BR. The thin film diffusion model, as the fundamental theory for leaching, either with constant particle size for selective leaching, or with shrinking particle size for less-, or non-, selective leaching, interprets sufficiently well the relevant experimental data. In both cases, a concept for an unyielding core supplements the basic model. Especially for the selective leaching mild conditions, the simplest model version keeps step with the experiments, since both prove 1^st order kinetics, while especially for the extreme conditions including very low solvent excess, it is proposed a combined conversion rate model with diffusion and chemical reaction inside particles. The maximization of Sc recovery per unit of consumed solvent (i.e., specific recovery) emerged as highly critical for the process economics.

The aim of this randomized controlled clinical trial was to compare the 2-year clinical performance of resin composite restorations placed at non-caries cervical lesions (NCCL) with one-step self-etch, total-etch, and selective enamel etch & self-etch adhesive techniques. Thirty-two patients received three resin composite restorations each at NCCLs (Tetric EvoCeram/Ivoclar/Vivadent), bonded with a total-etch adhesive agent (ExciTE F/Ivoclar/Vivadent) and a self-etch (AdheSE One F/Ivoclar/Vivadent) without and with selective enamel etching. All restorations were evaluated by two examiners at baseline, 6-, 12-, 18- and 24-months post-operation regarding retention, caries occurrence, marginal adaptation, and marginal staining. A logistic regression analysis with generalized estimating equations was used. After 2 years, the retention rate was 86,8% for total-etch, 92.26% for self-etch, and 93.63% for selective enamel etching & self-etch. No caries were detected during all the restorations. Concerning marginal adaptation, the clinically perfect restorations were 26.9% for the total-etch technique, 16% for self-etch, and 25,9% for selective enamel etch & self-etch. All three adhesive strategies provided restorations with no significant differences in the retention rate and the marginal adaptation, whereas the total etch yielded better performance for marginal staining. All the restorations were assessed as clinically acceptable after 2 years.

Laser powder bed fusion (LPBF) is an additive manufacturing process employed in many industries, for example for aerospace, automotive and medical applications. In these sectors, mainly nickel-, aluminum- and titanium-based alloys are used. In contrast, the mechanical engineering industry is interested in more wear-resistant steel alloys with higher hardness, both of which can be achieved with a higher carbon content, like in high-speed steels. Since these steels are susceptible to cracking, preheating needs to be applied during processing by LPBF. In a previous study, we applied a base plate preheating temperature of 500 °C for HS6-5-3-8 with 1.3 % carbon content. We were able to manufacture dense (p > 99.9 %) and crack-free parts from HS6-5-3-8 with a hardness > 62 HRC (as built) by LPBF. In this study, we investigate the influence of preheating temperatures up to 600 °C on hardness and microstructure dependent on part height for HS6-5-3-8. The microstructure was studied by light optical microscopy (LOM), scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD). The analysis of hardness and microstructure at different part heights is necessary because state-of-the-art preheating systems induce heat only into the base plate. Consequently, parts are subjected to temperature gradients and different heat treatment effects depending on part height during the LPBF process.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

Recently, we developed Komagataella phaffii (formerly Pichia pastoris) as a model for lipophagy, the selective autophagy of lipid droplets (LDs). We found that lipophagy pathways induced by acute nitrogen (N) starvation and in stationary (S) phase have different molecular mechanisms. Moreover, both types of lipophagy are independent of Atg11, the scaffold protein that interacts with most autophagic receptors and, therefore, is essential for most types of selective autophagy in yeast. Since yeast aggrephagy, the selective autophagy of ubiquitinated protein aggregates, is also independent of Atg11 and utilizes the ubiquitin-binding receptor, Cue5, we studied the relationship of K. phaffii Cue5 with differentially induced LDs and lipophagy. While there was no relationship of Cue5 with LDs and lipophagy under N-starvation conditions, Cue5 accumulated on LDs in S-phase and degraded together with LDs via S-phase lipophagy. The accumulation of Cue5 on LDs and its degradation by S-phase lipophagy strongly depended on the ubiquitin-binding CUE domain and Prl1, the positive regulator of lipophagy 1. However, unlike Prl1, which is required for S-phase lipophagy, Cue5 was dispensable for it suggesting that Cue5 is rather a new substrate of this pathway. We propose that a similar mechanism (Prl1-dependent accumulation on LDs) might be employed by Prl1 to recruit another ubiquitin-binding protein that is essential for S-phase lipophagy.

Alpha-fetoprotein (AFP) is a major embryo- and tumor-associated protein capable of binding and transporting variety of hydrophobic ligands including estrogens. AFP has been shown to inhibit estrogen receptor (ER)-positive tumor growth and this can be attributed to its estrogen-binding ability. Despite AFP has long been investigated, its three-dimensional (3D) structure has not been experimentally resolved and molecular mechanisms underlying AFP-ligand interaction remain obscure. In our study we constructed homology-based 3D model of human AFP (HAFP) with the purpose to perform docking of ERα ligands, three agonists (17β-estradiol, estrone and diethylstilbestrol) and three antagonists (tamoxifen, afimoxifene and endoxifen) into the obtained structure. Based on ligand docked scoring function, we identified three putative estrogen- and antiestrogen-binding sites with different ligand binding affinities. Two high-affinity sites were located in (i) a tunnel formed within HAFP subdomains IB and IIA and (ii) opposite side of the molecule in a groove originating from cavity formed between domains I and III, while (iii) the third low-affinity site was found at the bottom of the cavity. 100 ns MD simulation allowed studying their geometries and showed that HAFP-estrogen interactions occur due to van der Waals forces, while both hydrophobic and electrostatic interactions were almost equally involved in HAFP-antiestrogen binding. MM/GBSA rescoring method estimated binding free energies (ΔG_bind) and showed that antiestrogens have higher affinities to HAFP as compared to estrogens. We performed in silico point substitutions of amino acid residues to confirm their roles in HAFP-ligand interactions and showed that Thr132, Leu138, His170, Phe172, Ser217, Gln221, His266, His316, Lys453, and Asp478 residues along two disulfide bonds, Cys224-Cys270 and Cys269-Cys277 have key roles in both HAFP-estrogen and HAFP-antiestrogen binding. Data obtained in our study contribute to understanding mechanisms underlying protein-ligand interactions and anti-cancer therapy strategies based on ER-binding ligands.

The new diprotic ligand 3,5-di-tert-butylsalicylaldehyde 4-ethyl-3-thiosemicarbazone, abbreviated H2(3,5-t-Bu2)-sal4eT, exists as the thio-keto tautomer and adopts the E-configuration with respect to the imine double bond as evidenced by single-crystal X-ray analysis and corroborated by spectroscopic characterisation. Upon treatment with Cu(OAc)2·H2O in the presence of either 2,9-dimethyl-1,10-phenanthroline (2,9-Me2-phen) or 1,10-phenanthroline (phen) as a co-ligand in MeOH, this thiosemicarbazone undergoes conformational transformation (relative donor-atom orientations: syn,anti → syn,syn) concomitantly with tautomerization and double deprotonation to afford the ternary copper(II) complexes [Cu{(3,5-t-Bu2)-sal4eT}(2,9-Me2-phen)] (1) and [Cu2{3,5-t-Bu2)-sal4eT}2(phen)] (2). Crystallographic elucidation has revealed that complex 1 is a centrosymmetric dimer of mononuclear copper(II) complex molecules brought about by intermolecular H-bonding. The coordination geometry at the copper(II) centre is best described as distorted square pyramidal in accord with the trigonality index (τ = 0.14). The co-ligand adopts an axial-equatorial coordination mode; hence there is a disparity between its two Cu–N coordinate bonds arising from weakening of the apical one as a consequence of the tetragonal distortion. The axial X-band ESR spectrum of complex 1 is consistent with retention of this structure in solution. Complex 2 is a centrosymmetric dimer of dinuclear copper(II) complex molecules exhibiting intermolecular H-bonding and π-π-stacking interactions. The two copper(II) centres, which are 4.8067(18) Å apart and bridged by the thio-enolate nitrogen of the quadridentate thiosemicarbazonate ligand, display two different coordination geometries, one distorted square planar (τ4 = 0.082) and the other distorted square pyramidal (τ5 = 0.33). Such dinuclear copper(II) thiosemicarbazone complexes, which are crystallographically characterised, are extremely rare. In vitro, complexes 1 and 2 outperform cisplatin as antiproliferative agents in terms of potency and selectivity towards HeLa and MCF-7 cancer cell lines.

Targeted therapies with antiangiogenic drugs (e.g., sunitinib) and immune checkpoint inhibitors (e.g., anti-PD-1 antibodies) are the standard of care for patients with metastatic renal cell carcinoma. Although these treatments improve patient survival, they are rarely curative. We previously hypothesized that advanced cancers might be treated without drugs by using artificial diets in which the levels of specific amino acids (AAs) are manipulated. In this work, after showing that AA manipulation induces selective anticancer activity in renal cell carcinoma cells in vitro, we evaluated the anticancer activity of 17 artificial diets in a challenging animal model of renal cell carcinoma. The model was stablished by injecting murine renal cell carcinoma (Renca) cells into the peritoneum of immunocompetent BALB/cAnNRj mice. Mice survival was markedly improved when their normal diet was replaced with our artificial diets. Mice fed a diet lacking six AAs (diet T2) lived longer than mice treated with sunitinib or anti-PD-1 immunotherapy; several animals lived very long or were cured. Controlling the levels of several AAs (e.g., cysteine, methionine and leucine) and lipids was important for the anticancer activity of the diets. Additional studies are needed to further evaluate the therapeutic potential of this simple and inexpensive anticancer strategy.

This review is focused on synephrine, the principal phytochemical found in bitter orange and other medicinal plants, and widely used as a dietary supplement for weight loss/body fat reduction. We examine different aspects of synephrine biology, delving into its established and potential molecular targets, as well as its mechanisms of action. We present an overview of the origin, chemical composition, receptors, and pharmacological properties of synephrine, including its anti-inflammatory and anti-cancer activity in various in vitro and animal models. Additionally, we conduct a comparative analysis of the molecular targets and effects of synephrine with those of its metabolite, selective glucocorticoid receptor agonist (SEGRA) Compound A (CpdA), which shares a similar chemical structure with synephrine. SEGRA, including CpdA, have been extensively studied as glucocorticoid receptor activators that have a better benefit/risk profile than glucocorticoids due to the reduced adverse effects. We discuss the potential of synephrine usage as a template for the synthesis of new generation of non-steroidal SEGRA. The review also provides insights into the safe pharmacological profile of synephrine.

Vit-106 is a promising zirconium-based alloy with high glass-forming ability and belongs to the so-called bulk metallic glasses (BMG). Workpieces with a size of around one centimeter in all three dimensions can be obtained from a BMG alloy by casting. However, further increasing the cast size decreases the cooling rate and thus induces crystallization. Selective laser melting (SLM) is a well-known technique to overcome the size limitations for BMGs because a workpiece is built by the addition of multiple melt portions where the cooling rate is kept above the critical one. Currently, BMG parts obtained by SLM suffer from partial crystallization. The present work studies the influence of SLM process parameters on partial crystallization of Vit-106 by metallography and the influence of the microstructure on mechanical properties by microhardness and wear resistance testing. Submicron crystalline inclusions are observed in an amorphous matrix of Vit-106 alloy obtained by SLM. The size and the concentration of the inclusions can be controlled by varying the laser scanning speed. It is shown that submicron crystalline inclusions formed in the amorphous matrix during SLM can favorably affect microhardness and wear resistance.

A useful and increasingly common additive manufacturing (AM) process is the selective laser melting (SLM) or direct metal laser sintering (DMLS) process. SLM/DMLS can produce full-density metal parts from difficult materials, but it tends to suffer from severe residual stresses introduced during processing. This limits the usefulness and applicability of the process, particularly in the fabrication of parts with delicate overhanging and protruding features. The purpose of this study was to examine the current insight and progress made toward understanding and eliminating the problem in overhanging and protruding structures. To accomplish this, a survey of literature was undertaken, focusing on process modeling (general, heat transfer, stress and distortion, and material models), direct process control (input and environmental control, hardware-in-the-loop monitoring, parameter optimization, and post-processing), experiment development (methods for evaluation, optical and mechanical process monitoring, imaging, and design-of-experiments), support structure optimization, and overhang feature design; approximately 140 published works were examined. The major findings of this study were that a small minority of the literature on SLM/DMLS deals explicitly with the overhanging stress problem, but some fundamental work has been done on the problem. Implications, needs, and potential future research directions are discussed in-depth in light of the present review.

Spinal Cord (SC) Anatomy is often assimilated to a morphologically encapsulated neural entity, but its functional anatomy remains only partially understood. We hypothesized that it could be possible to reexplore SC neural networks by performing live electrostimulation mapping, based on “super-selective” Spinal Cord Stimulation (SCS), originally designed as a therapeutical tool to address chronic refractory pain. As a starting point, we initiated a systematic SCS lead programming approach using live electrostimulation mapping on a chronic refractory perineal pain patient, previously implanted with multicolumn SCS at the level of the conus medullaris (T12-L1). It appeared possible to (re)explore the classical anatomy of the conus medullaris using statistical correlations of paresthesia coverage mappings, resulting from 165 different electrical configurations tested. We highlighted that sacral dermatomes were not only located more medially but also deeper than lumbar dermatomes at the level of the conus medullaris, in contrast with classical anatomical descriptions of SC somatotopical organization. As we were finally able to find a morpho-functional description of ‘Philippe-Gombault’s triangle’, in 19th century historical textbooks of neuroanatomy, matching remarkably with these conclusions, the concept of “Neuro-Fiber-Mapping” was introduced.

Because this issue journal is dedicated to Gelatin here we present a few applications of gelatin in the field of optics. It is understood that optics is the science that studies the production, propagation, interaction and detection of light. Regarding the detection there are some materials sensitive to light (photosensitive) that are used like photomultipliers, CCD’s, crystals, two dimension (2D) materials and more. Among the 2D materials the most popular through several centuries has been gelatin based photographic emulsion that records spatial distributions of light. More recently (1970) films made of Gelatin with Dichromate (DCG) and dyes have been used. We describe some characteristics and applications of these two photosensitive materials. Also we describe examples where gelatin is used as Relative Humidity (RH) sensor and in the fabrication of optical elements based on gelatin. This article is intended to researchers outside the optics community.

Abstract: Beetroot (Beta vulgaris L) has been known for being a rich source of phytochemicals, minerals and vitamins. This study presents a model system for how the combination of extrac-tion/chromatography/mass spectrometry and NMR offers an efficient way to profile metabolites in the extracts of a natural product, beetroot . Such combination may lead to the identification of more nutritional or medicinal compounds in natural products, and it is essential for our ongoing investigation to study the selective adsorption/desorption of these metabolites on nanoparticles. The aqueous and organic extracts underwent analyses using UV-vis spectroscopy; GC-MS; LC-MS; 1H, 13C, TOCSY, HSQC, and selective TOCSY NMR experiments. Polar Extract: The two forms of betalain pigment were identified by UV-vis and LC MS. Fourteen amino acids, sucrose, and other compounds among which is riboflavin, were identified by LC-MS. 2D TOCSY showed the spin coupling correlations corresponding to some of these compounds. The HSQC spectrum showed 1H/13C spin correlation in sucrose confirming the high abundance of sucrose in beetroot. Organic Extract: GC-MS data enabled the identification of several compounds including six fatty acid methyl esters (FAME) with higher than, on average, 90% similarity score. Selective TOCSY NMR data showed the spin coupling pattern corresponding to oleic, linoleic, and linolenic fatty acids. 31P NMR spectra indicate that phospholipids exist in both the organic and aqueous phases. Keywords: Beetroot (Beta vulgaris L); Total Correlation Spectroscopy (TOCSY); Gas Chromatog-raphy-Mass Spectrometry (GC-MS); selective TOCSY, Homonuclear single quantum correlation (HSQC); fatty acid methyl esters (FAME).

A genome-wide association study (GWAS) was performed on a set of 260 lines which belong to three different bi-parental flax mapping populations. These lines were sequenced to an averaged genome coverage of 19× using the Illumina Hi-Seq platform. Phenotypic data for 11 seed yield and oil quality traits were collected in eight year/location environments. A total of 17,288 single nucleotide polymorphisms were identified, which explained more than 80% of the phenotypic variation for days to maturity (DTM), iodine value (IOD), palmitic (PAL), stearic, linoleic (LIO) and linolenic (LIN) acid contents. Twenty-three unique genomic regions associated with 33 QTL for the studied traits were detected, thereby validating four genomic regions previously identified. The 33 QTL explained 48-73% of the phenotypic variation for oil content, IOD, PAL, LIO and LIN but only 8-14% for plant height, DTM and seed yield. A genome-wide selective sweep scan for selection signatures detected 114 genomic regions that accounted for 7.82% of the flax pseudomolecule and overlapped with the 11 GWAS-detected genomic regions associated with 18 QTL for 11 traits. The results demonstrate the utility of GWAS combined with selection signatures for dissection of the genetic structure of traits and for pinpointing genomic regions for breeding improvement.

Perhaps the greatest challenge in the graft copolymerization of acrylic acid onto starch initiated by Fenton’s is the selectivity of the grafting reaction. Low selectivity means that too much of unwanted homopolymer polyacrylic acid is produced. In this paper, it has been analyzed why with this reaction system, involving a water soluble monomer and indirect initiation, the graft selectivity is such a challenge. Several other grafting reactions, especially with monomers of low water solubility or when direct initiation is applied, show a better grafting performance. A scheme is presented based on reaction engineering principles, that supports an explanation of the observed differences. A more selective activation of starch is a factor, but perhaps even more important is a low monomer to starch ratio at the starting sites of graft reactions. Based on these insights, several methods to improve the graft selectivity are evaluated, with the help of literature data but mostly by experimental explorations in our laboratory. Most promising appears to be a dedicated dosage method, to add monomer in portions over time, tested in a batch reactor with gelatinized cassava starch. This way, both grafting percentage and graft selectivity could be improved. Such could not be realized with the more conventional dosage, which is to add all monomer before the start of the reaction. This can be considered a principal breaktrough. Still, more research and development would be needed to refine the method and to implement the idea also in a continuous reactor at larger scale.