The control of alumina morphology is crucial yet challenging for its various applications. Un-fortunately, traditional methods for preparing alumina particles suffer from several limitations such as irregular morphology, poor dispersibility, and restricted application areas. In this study, we develop a novel method for preparing spherical mesoporous alumina using chitin and Plu-ronic P123 as mixed templates. The effects of reaction temperature, time, and the addition of mixed templates on the phase structure, micromorphology, and optical absorption properties of the samples were investigated. The experimental results indicate that lower temperature and shorter reaction time facilitated the formation of spherical mesoporous alumina with excellent CO2 adsorption capacity. The periodic density functional theory (DFT) calculations demonstrate that both (110) and (100) surfaces of γ-Al2O3 can strongly adsorb CO2. The difference in the amount of CO2 adsorbed by Al2O3 is mainly due to the different surface areas, which give dif-ferent number of exposed active sites. This approach introduces a novel strategy for utilizing bi-ological compounds to synthesize spherical alumina and greatly enhances mesoporous alu-mina's application efficiency in adsorption fields. Moreover, the study explored the electro-chemical performance of the synthesized product using cyclic voltammetry and discovered im-proved loading of electrocatalysts and enhanced electrocatalytic activity.

Co-based catalysts have gained significant attention in recent years due to their excellent ability to activate C-H bonds and high selectivity towards olefins, despite being a non-noble and environmentally unfriendly metal. However, further improvements are necessary for practical utilization, particularly in terms of activity and anti-carbon deposition capacity. In this study, we synthesized Al₂O₃ nanorods with abundant pentacoordinated Al³⁺ (Al³⁺_penta) sites. The supported Co on the Al₂O₃ nanorod (Co/Al₂O₃-NR) exhibited higher selectivity (>96% propylene selectivity) and stability (deactivation rate 0.15 h^-1), compared to Co supported on an Al₂O₃ nanosheet with fewer pentacoordinated Al³⁺ sites. Various characterizations confirmed that Co(II) mainly exists as CoAl₂O₄ rather than Co₃O₄ in the form of Co/Al₂O₃-NR, which inhibits the reduction of Co(II) to Co0 and improves catalyst stability accordingly.

The continuous casting nozzle which guides and protects the flow of liquid steel undergoes a progressive reduction in its internal diameter following the accumulation on the internal wall of non-metallic inclusions. This narrowing of the channel is due to a mechanical attachment (non-metallic inclusions) and this, because of the turbulent regime of the flow of the liquid steel. This phenomenon is very often associated with the casting of low carbon steels deoxidized exclusively with aluminium. Clogging generally leads to a slowing down of the casting speed and, in severe cases, to the total stoppage of the installation and consequently to the appearance in the slab of the defect called "resumption of casting or belt". The aim of this work is to determine the nature of the deposit and the blocking mechanism of the pouring nozzles. For that, a chemical analysis as well as tests concerning the adhesion of the deposit were carried out on samples taken from damaged pouring nozzles. We found that it was at a load of 187.5 kgf that the rupture of the sample took place, during the interfacial indentation tests, which represents a very high level of adhesion. On the other hand, chemical analysis by X-ray fluorescence of the deposits revealed a fairly high level of alumina (Al₂O₃ = 90%) which undoubtedly comes from inclusions resulting from the deoxidation of the metal. It can therefore be said that the clogging phenomenon is produced by a continuous attachment of non-metallic inclusions to the rough walls of the nozzle.

Alumina dispersion-strengthened copper, Glidcop, is used widely in high-heat-load ultra-high-vacuum components for synchrotron light sources (absorbers), accelerator components (beam intercepting devices) and in nuclear power plants. Glidcop has similar thermal and electrical properties to OFE (oxygen free electrical) copper, but has superior mechanical properties, thus making it a feasible structural material; its yield and ultimate strength are equivalent to those of mild-carbon steel. The purpose of this work has been to develop a brazing technique to join Glidcop to Mo, using a commercial Cu-based alloy. The effects of the excessive diffusion of the braze along the grain boundaries on the interfacial chemistry and joint microstructure, as well as on the mechanical performance of the brazed joints, has been investigated. In order to prevent the diffusion of the braze into the Glidcop alloy, a copper barrier layer has been deposited on Glidcop by means of RF-sputtering.

An amorphous silicon carbide (SiC) membrane with H2 permeance of 1.2E-7 mol･m^-2･s^-1･Pa^-1 and excellent H₂/CO₂ selectivity of 2600 at 673 K was successfully synthesized on a Ni-gamma-alumina-coated alpha-alumina porous support by counter diffusion chemical vapor deposition (CDCVD) using silacycrobutane (SCB) at 788 K. The dominant permeation mechanism for He and H₂ in the temperature range 323-673 K was activated diffusion. The SiC active layer was formed in Ni-gamma-Al₂O₃ intermediate layer. The thermal expansion coefficients mismatch between SiC active layer and Ni-gamma-Al₂O₃-coated alpha-Al₂O₃ porous support was eased by the low decomposition temperature of SiC source and membrane structure.

The addition of active seed for increasing the precipitation rate leads to the formation of fine Al(OH)3 particles that complicates separation of solid from the mother liquor. In this study, the enhanced precipitation of coarse Al(OH)3 from sodium aluminate solution using active agglomerated seed was investigated. Aluminum salt (Al2(SO4)3) were used for active agglomerated seed precipitation at the initial of the process. About 50% of precipitation rate was obtained when these agglomerates were used as a seed in the amount of 20 g L–1 at 25 °C within 10 h. The agglomerated active seed and precipitate samples were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FTIR). SEM images showed that agglomerates consist of flake-like particles that can be stick together by bayerite (β-Al(OH)3) acting as a binder. The precipitation temperature above 35 °C and the high concentration of free alkali (αk > 3) lead to the agglomerates refinement that can be associated with the bayerite dissolution.

In this investigation magnetic γ-Al2O3 ceramic nanocomposite particles bearing epoxide functionality are prepared following a multistep process. The ultimate nanocomposite particles are named as γ-Al2O3/Fe3O4/SiO2/poly(glycidyl methacrylate (PGMA). The surface property is evaluated by carrying out the adsorption study of Remazol navy (RN), a model reactive azo dye, on both γ-Al2O3/Fe3O4/SiO2 and γ-Al2O3/Fe3O4/SiO2/PGMA nanocomposite particles. The adsorption is carried out at the point of zero charge (PZC) to neutralize the effect of particle surface charge. The adsorption rate is very fast, reached equilibrium (qe) value within five min. Due to mesoporous structure of silica layer γ-Al2O3/Fe3O4/SiO2 nanocomposite particles possessed relatively higher specific surface area and magnitude of adsorption is dependent on the total specific surface area. The introduction of epoxide functionality favored high adsorption capacity in mass per unit surface area. The adsorption process strictly followed Langmuir model. Thermodynamic equilibrium parameters implied that irrespective of surface functionality the adsorption process is spontaneous and exothermic. Pseudo-second-order rate kinetic model is more appropriate to explain the adsorption kinetics.

Porous α-Al2O3 ceramics is a highly demanded material for multitude applications such as filters, substrates, biomedicine materials, etc. Despite the availability of the raw materials, a challenge of their technology is in a high energy budget caused by the sintering above 1500 °C. For a cold sintering processing (CSP) of ceramics, the lowering of α-Al2O3 sintering temperature is one of the most urgent challenges at the background of its rapid development. The current paper for the first time demonstrates the solution of the mentioned problem by the CSP of α-alumina ceramics in a presence of pure water as a transient liquid. The manufactured materials were examined by XRD analysis; the evolution of their microstructures during the CSP was revealed by SEM, and the porosity evaluated by the Archimedes method. The ceramics with an open porosity up to 36 % was produced at 380-450 °C, 220 MPa in 30 min. An increase in the pressure was found to impede α-Al2O3 formation from γ-AlOOH. The development of the microstructure was discussed within the frameworks of the dissolution-precipitation model and the homogenous nucleation. The results of the SEM study pointed to the coalescence of γ-AlOOH grains during the CSP.

MCrAlYHf bond coats are employed in jet and aircraft engines, stationary gas turbines, and power plants, which require strong resistance to oxidation at high temperatures. The oxidation behavior of a free-standing CoNiCrAlYHf coating was investigated in this study. Isothermal oxidation tests were performed in air at 1050 °C on the specimens with various levels of surface roughness to investigate the oxidation kinetics. X-ray diffraction, focused ion beam, scanning electron microscopy (SEM), and scanning transmission electron microscopy were used to characterize the surface oxides. The surface roughness was examined using a contact profilometer and SEM. An empirical model was proposed to elucidate the impact of surface roughness on the oxidation behavior based on the correlation between the surface roughness level and oxidation rates.

The oil produced in the oil fields of the Republic of Kazakhstan contains a high percentage of sulfur. Synthesis and improvement of the properties of catalytic systems for the production of fuels with high octane number and low sulfur content is currently an urgent task for Kazakhstan. In this study, catalytic systems with a new composition based on zeolites with the addition of rare-earth metals (E) and phosphorus (P) have been prepared and tested in the process of the catalytic hydrotreating of straight-run gasoline and gasoline of catalytic cracking. In case of NiO-MoO3-E-P-HZSM-HY-Al2O3 catalyst, the octane rating of the gasoline after hydro-processing was increased to 88-90, which is much higher than for other catalysts. The octane number of straight-run gasoline up to 400°C is a maximum of 90 (Research Method) and 83.7 (Motor Method). At the same time, the sulfur content in the resulting gasoline decreases from 0.0088% to 0.0011%. In the case of catalytic cracking gasoline, the sulfur content is reduced from 0.0134% to 0.0012%. The smallest residual sulfur content in the final product, 0.0005% is revealed in case of catalyst CoO-WO3-E-P-HZSM-HY-Al2O3, and it is 2-4 times lower than for catalysts CoO-MoO3-E-P-HZSM-HY-Al2O3 and NiO-MoO3-E-P-HZSM-HY-Al2O3. These amounts of sulfur residue in raw materials is lower than that required by the Euro-5 Standard. The surface of the prepared catalysts was 211.0-274.0 m2/g, diameter of pores d ≈ 1.5-2.5 nm and d ≈ 7.0 nm. The total pore volume of the catalysts was not higher than 0.28-0.41 ml/g. The catalysts developed in this study can be used for hydrotreating raw materials and producing high-octane gasoline with a low sulfur content, corresponding in its characteristics to the Euro-5 Standard.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

This paper reports on the fabrication of alumina doped preforms using MCVD-vapor phase chelate delivery system with Al(acac)3 as the precursor. The objectives of the work are to study the deposition process, the efficiency of the fabrication process, and the quality of the fabricated fiber preforms. Two parameters are studied, Al(acac)3 sublimator temperature (TAl°C) and deposition direction (i.e. downstream and upstream). Other parameters such as oxygen flow and deposition temperature are fixed. The results showed that a high uniformity of refractive index difference (%RSD < 2%) and core size (%RSD < 2.4%) was obtained along the preform length using downstream deposition while for the combined upstream and downstream deposition the uniformity was deteriorated. The process efficiency was found to be about 21% for TAl°C of 185°C and downstream deposition. From the EDX elemental analysis, the refractive index was found to increase by 0.0025 per mole percent of alumina.

Enhanced oil recovery using nanoparticles is a promising method. However, when injected into a reservoir, nanoparticles can block pores and cause permeability damage. Therefore, enhancing their performance to lower the permeability damage effect is crucial. This study investigated the effect of pH alteration through carbon dioxide (CO2) injection on the permeability damage of limestone caused by the aluminum oxide (α-Al2O3) nanofluid. The methodology involved nanofluid alternating CO2 core flooding experiments by using nanofluids with pH of 4.5 and 2.8. After core flooding, permeability damage was calculated as a percentage of the reduction of the original permeability. The results revealed that the permeability damage in the case of nanofluid alternating CO2 injection was 23.23%. In only nanofluid with a pH of 4.5 injection case, permeability damage was 47.53%. In the 2.8 pH nanofluid injection case, permeability damage was 31.01%. The retention of nanoparticles was confirmed through scanning electron microscopy and energy dispersive X-ray analysis. Permeability damage could be attributed to a large nanoparticles’ agglomeration size, roughness of pore surfaces, and nanoparticle sedimentation. The results of the study revealed that altering pH through the α-Al2O3 nanofluid alternating CO2 injection can effectively reduce the permeability damage of limestone.

A developing energy-saving approach of cold sintering in a pure aqueous medium was applied to the preparation of α-Al2O3 ceramics and performed on spark plasma sintering equipment. The initial γ-Al(OH)3 and γ-AlOOH powders and the cold-sintered ceramics were studied by X-ray diffraction analysis, infrared spectroscopy, thermal analysis, and scanning electron microscopy to reveal the chemical and structural transformations they experienced during the cold sintering. At 450°C and 70 MPa, initial γ-AlOOH transformed into a fragile α-Al2O3 material. Porous α-Al2O3 ceramics with about 60% porosity was obtained after cold sintering of γ-Al(OH)3 in the same conditions combined with subsequent annealing at 1250°C for 3 h. The role of water molecules in the studied processes was considered as the enhancement of structural mobility in the cold-sintered material due to its reversible hydroxylation similar to earlier investigated supercritical water action on the precursors during α-Al2O3 formation. Further improvement of the cold sintering setup and regimens would open prospects in α-Al2O3 ceramics manufacturing by an ecologically benign route.

. In this work, two types of nanoporous alumina membranes were prepared using different acids and were tested. Structural features of the samples were investigated by scanning electron spectroscopy and further by different types of fractal dimension estimation methods. Transmission and scattering of accelerated He+ ions were studied in experiments on ion irradiation of dielectric channels based on porous alumina. Ion accelerator was used as a source of the He+ beam with an energy of 1.7 MeV. A scattering of ions was studied by Rutherford backscattering spectrometry. Helium transition through nanoporous alumina at various angles between the normal to the sample and the beam direction were observed. It is shown that the porous structure of anodic aluminum oxide is excellent as a dielectric matrix of nanocapillaries. Owing to the small angle scattering, it allows the transportation of the accelerated charged particles through the dielectric capillaries, and, as a result, localization of high energy ion irradiation effects. Additionally, according to the transmission UV-Vis spectra the energy gaps of samples obtained were calculated.

This study investigates the contribution of nano-alumina (nA: 1-3wt.% binder) to the performance of silica fume (SF-10%) blended mortar in ternary blended mortar. The fresh (workability, setting time) and hardened properties (compressive strength and thermal resistance (300 °C for 1 h)), were examined. Nano alumina (nA) contributed positively to the consistency of SF blended mortar such that similar workability could be achieved with OPC when 3% nA was added. The initial and final setting time of 180 and 220 mins were recorded in SF blended mortar and reduced by 18.4 and 21.8%, respectively by adding 3%nA. The optimum mixture that contained 10%SF and 2%nA had 3-d and 28-d compressive strengths of 28 and 43.2 MPa. In the absence of nA, this reduced by 14.3% and 29.4% while it reduced by 25.2% and 16.7%, respectively in OPC mortar. The main products characterizing SF-nA ternary blended binder with dense microstructural density were nepheline and tobermorite. Besides, it is more susceptible to carbonation despite its superior performance in thermal resistance when compared to SF blended and OPC mortars.

Aseptic implant loosening after total joint replacement is partially influenced by material-specific factors when cobalt-chromium alloys are used, including osteolysis induced by wear- and corrosion products, and stress shielding. Here, we aim to characterize a hybrid material consisting of alumina-toughened zirconia ceramics (ATZ) and additively manufactured Ti-35Nb-6Ta (TiNbTa), joined by a glass solder. The structure of the joint, static and fatigue shear strength, the influence of accelerated aging, and the cytotoxicity using an elution assay with human osteoblasts is characterized. Furthermore, the biomechanical properties of functional demonstrators of a femoral component for total knee replacements are evaluated. TiNbTa-ATZ specimens showed a homogenous joint with statistical distributed micro-pores and a slight accumulation of Al-rich compounds at the glass solder-TiNbTa interface. The static shear strength was 26.4 ± 4.2 MPa (Ti-ATZ reference: 38.2 ± 14.4 MPa, p = 0.117), all specimens survived 107 cycles of shear loading to 10 MPa, and aging did not reduce the strength. TiNbTa-ATZ did not impair the proliferation and metabolic activity of human osteoblasts. Functional demonstrators of TiNbTa-ATZ provided a maximum bearable extension-flexion moment of 40.7 ± 2.2 Nm. Biomechanical and biological properties of TiNbTa-ATZ demonstrate potential application for endoprosthetic implants.

Red mud is a hazardous waste of alumina industry that contains high amounts of iron, aluminum, titanium and REEs. One of the promising methods for the extraction of iron from red mud is car-bothermic reduction with the addition of sodium salts. This research focuses on the process of hy-drochloric high-pressure acid leaching using 10–20% HCl of two samples of non-magnetic tailings obtained by 60-minute carbothermic roasting of red mud at 1300 °C and the mixture of 84.6 wt. % of red mud and 15.4 wt. % Na2SO4 at 1150 °C, respectively, with subsequent magnetic separation of metallic iron. An influence of temperature, leaching duration, solid-to-liquid-ratio and acid con-centration on dissolution behavior of Al, Ti, Mg, Ca, Si, Fe, Na, La, Ce, Pr, Nd, Sc, Zr were studied. Based on the investigation of the obtained residues, mechanism of passing of valuable elements into the solution was proposed. It has shown that 90% Al, 91% Sc and above 80% of other REEs can be dissolved under optimal conditions; Ti can be extracted into the solution or the residue depending on the leaching temperature and acid concentration. Based on the research results, novel flowsheets for red mud treatment were developed.

The study aims to elaborate a neural model and algorithm for optimising hardness and porosity of coatings and thus ensure that they have superior cavitation erosion resistance. Al2O3-13wt.%TiO2 ceramic coatings were deposited onto 316L stainless steel by atmospheric plasma spray (ASP). The coatings were prepared with different values of two spray process parameters: the stand-off distance and torch velocity. Microstructure, porosity and microhardness of the coatings were examined. Cavitation erosion tests were conducted in compliance with the ASTM G32 standard. Artificial neural networks (ANN) were employed to elaborate the model, and the multi-objectives genetic algorithm (MOGA) was used to optimise both properties and cavitation erosion resistance of the coatings. Results were analysed with Matlab software by Neural Network Toolbox and Global Optimization Toolbox. The fusion of artificial intelligence methods (ANN+MOGA) is essential for future selection of thermal spray process parameters, especially for the design of ceramic coatings with specified functional properties. Selection of these parameters is a multicriteria decision problem. The proposed method made it possible to find a Pareto front, i.e. trade-offs between several conflicting objectives – maximising the hardness and cavitation erosion resistance of Al2O3-13%TiO2 coatings and, at the same time, minimizing their porosity.

Advanced ceramics are recognized as key enabling materials possessing combinations of properties not achievable in other material classes. They are characterized by very high thermal, chemical and mechanical resistance and also usually have a lower density than metals. These properties predestine ceramics for many different applications, especially space applications.In the aerospace sector aerospike nozzles promise performance and application advantages compared to classic bell nozzles but are also inherently more complex to manufacture due to their shape. AM methods drastically simplify or even enable the fabrication of those complex structures while minimising the number of individual parts. The applicability of ceramic AM (“CerAMfacturing”) on rocket engines and especially nozzles is consequently investigated in the frame of the “MACARONIS” project, a cooperation of the Institute of Aerospace Engineering at Technische Universität Dresden and the Fraunhofer Institute for Ceramic Technologies and Systems (IKTS) in Dresden. The goal is to develop novel large size aerospike thrust nozzles including areas of highest resolution and fineness. Finding a suitable AM process that enables the realisation of both aspects is extremely challenging. One possibility could be the hybridization of shaping methods, in that case CerAM VPP (ceramic additive manufacturing via vat photopolymerization) and CerAM FFF (ceramic additive manufacturing via fused filament fabrication) in combination with sinter joining. This contribution focuses on the high resolution CerAM VPP process, in particular the development, characterization and testing of a new photoreactive Al₂O₃ suspension validated by AM of novel aerospike nozzles.