Sound absorbing materials are used in building to dissipate sound energy into heat by viscous and thermal processes. Sound absorbers increase the transmission loss of walls, decrease the reverberation time of rooms and attenuate the noise generated by internal sound sources. Porous absorbers (fibrous, cellular or granular) are the most used materials in noise control applications, since their high performance-to-cost ratio in the frequency band of interest. However, when cleaning and health reasons are of concern, microperforated panel (MPP) absorbers can be preferred. MPPs, consisting of many minute (sub-millimetric) holes in a panel, are tunable absorbers in a prescribed frequency band, which main shortcomings are high manufacturing cost and limited absorption frequency band. Production cost of MPP can nowadays be drastically cut down by means of modern techniques. Absorption frequency band can be considerably enlarged by designing multiple-layer MPPs (ML-MPPs). The aim of this article is to review the high potential of ML-MPPs as a modern, clean and healthy alternative of porous materials for sound absorption.

The utilization of vegetal fabric reinforced cementitious matrix (FRCM) represents an innovative approach to composite materials, offering distinct sustainable advantages when compared to traditional steel-reinforced concrete and conventional FRCM composites employing synthetic fibers. This article introduces a design for sandwich solutions based on a core of extruded polystyrene and composite skins combining mortar as a matrix and diverse vegetal fabrics as fabrics such as hemp and sisal. The structural behavior of the resulting sandwich panel is predominantly driven by the interaction between materials (mortar and polyurethane) and the influence of shear connectors penetrating the insulation layer. This study encompasses an experimental campaign involving double-shear tests, accompanied by heuristic bond-slip models for potential design of sandwich solutions. The analysis extends to the examination of various connector types, including hemp, sisal, and steel, and their impact on the shear performance of the sandwich specimens. The results obtained emphasize the competitiveness of vegetal fabrics in achieving effective composite strength comparable to other synthetic fabrics like glass fiber. Nevertheless, the study reveals that the stiffness of steel connectors outperforms vegetal connectors, contributing to an enhanced improvement in both stiffness and shear strength of the sandwich solutions

Broadband noise reduction over the low-mid frequency range in the building and transportation sectors requires compact lightweight sound absorbers of typical sub-wavelength size. The use of multi-layered closely-spaced (micro-)perforated membranes or panels, if suitably optimized, contribute to these objectives. However, their elasticity or modal behaviors often impede the final acoustical performance of the partition. The objective of this study is to get insights into the vibrational effects induced by elastic limp membranes or panels volumetric modes on the optimized sound absorption properties of acoustic fishnets and functionally-graded partitions (FGP). Cost-efficient global optimization of the partition total frequency-averaged dissipation is achieved from simulated annealing with vibrational effects included through an impedance translation method. Critical coupling analysis reveals how the membranes or panels vibrations redistribute the locations of the Hole-Cavity resonances as well as their cross-coupling with the panels first volumetric mode. It is found that elastic limp micro-perforated membranes broaden the first pass-band of acoustic fishnets while smoothing out the dissipation ripples over the FGP optimiza-tion bandwidth. Moreover, the resonance frequency of the first panels mode sets an upper limit to the broadband optimization of FGPs, up to which high dissipation, low reflection and low trans-mission can be achieved.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The rapid development of the photovoltaic (PV) industry will result in an increase in the amount of electrical and electronic waste from used PV panels. Only in Poland, the total capacity installed in photovoltaic sources in Poland in May 2020 exceeded 1,950 MW, and the installation weight was approximately 120,000. tone. The problem arises in the recycling or management of this waste. This work presents methods used to recycle waste into photovoltaic modules. The authors investigated the possibility of mechanical and chemical processing of crystalline silicon. A method of thermal treatment of the panel was also proposed. As a result of the research, it was found that the stage of separating materials (crystalline cream, EVO foil, aluminum frame) plays an important role in the recycling process, which is not easy. Chemical treatment allows the silicon to become plastic and the temperature melts the back layer of the panel.

In recent years, intensive work has been carried out to achieve maximum energy production in photovoltaic power plants. Today, this challenge has to be solved for arrays of solar panels that move with the object on which they are installed (vehicles, trucks, ships, etc.). The present work tries to find the best solution for both constant voltage systems and for cases of maximum intensity. Once found, these solutions will be applied in real time for the dynamic recharging of battery packs, trying to achieve energetically autonomous vehicles.To solve these situations, a new computational method of voltage and amperage calculation has been developed in this paper, based on Dijkstra’s minimum path finding algorithm on graph theory, adapted to electrical circuits. For this purpose, panel performance analysis sensors, developed at the University of Malaga, have been combined with different electronic solutions (wifi relay devices using esp8266 or similar chips) achieving an accurate and sufficiently fast solution at very low cost. With this, series or parallel configurations can be carried out depending on the type of energy generation sought. The theoretical solutions using Minkowski paths, achieved in the past, have been simulated and subsequently constructed in this article, indicating the diagrams necessary for their realisation.

The paper presents theoretical, experimental and numerical studies on the thermal behavior of mineral wool used in sandwich panels. The aim of this study is to investigate the thermal properties of mineral wool at elevated temperatures and provide a simple model that would allow to determine the heat propagation in sandwich panels during fire. The paper proposes a new method to experimentally evaluate thermal diffusivity, derived from theoretical premises. Experiments are conducted in a laboratory furnace, where specimens are placed and temperatures inside specimens are measured. Different methods are used to process the test results and calculate the thermal diffusivity of mineral wool. Finally, a numerical analysis of heat transfer using finite element method (FEM) is performed to validate the obtained thermal properties.

In this paper, the seven traditional models of PV modules are reviewed comprehensively to find out the appropriate model to be reliable. All the models are validated using the Matlab code and make a graphical comparison. The accuracy and convergence of each model are evaluated using data of manufactured PV panels. Then, a novel model is proposed showing its consistent performance. The most three key parameters of single-diode model are self revised to adapt to various type of PV modules. This new method is verified in three types of PV panels' data measured by National Renewable Energy Laboratory (NREL), US. The validated data show promising results when the error RMSEs' range of the proposed model is under 0.36.

The There are many factors influencing the performance of photovoltaic (PV) systems. Among these factors, temperature and solar radiation are two major parameters that have a large effect on the efficiency of PV systems. The cell temperature of PV panels is related to the ambient temperature while the solar radiation incident on the surface of the PV modules depends on the slope and azimuth of these modules. Furthermore, ground reflectance (albedo) affects the irradiance incident on the PV panel surface, which in turn affects the output of a PV system. Nevertheless, the effects of these factors on the economic performance of the solar PV systems are scarcely reported. This paper presents a complete design of a stand-alone PV/battery system to supply electric power for a mobile base station in Choman, Erbil, Iraq. The effects of different factors on the total electricity produced by PV arrays and its economic performance are simultaneously investigated. HOMER software has been used as a tool for the techno-economic and environmental analysis. As indicated from the simulation results, the PV array capacity and its economic performance are highly affected by the variation of the slope and azimuth. With a base case (albedo of 20% and average annual ambient temperature of 11°C), the best feasible system which is achieved by facing PV due to south with a tilt angle of 40° or 45°, is found to have net present cost (NPC) of 70595 $ and cost of energy (COE) of 0.54 $/kWh. Moreover, the results indicate that increasing the ground reflectance from 10% to 90% results in a 7.2% decrease in the PV array capacity and about 3% decrease in the NPC and COE. On the other hand, increasing the ambient temperature from 0°C to 40°C results in a 19.7% increase in the PV array capacity and an 8.2% increase in the NPC and COE. Furthermore, according to the ambient temperature of Choman, using PV modules with high sensitivity to temperature is found to be an attractive option. Provided simulation performance analysis proves that the studied parameters must be treated well to establish an enabling environment for solar energy development in Iraq.

Increasing of renewable energy share in total energy production is a direction that leads towards European Union’s aims of carbon neutrality by 2050, as well as increases energy self-sufficiency and independence. Some of the main challenges to increase renewable energy share while providing efficient and secure energy supply are related to optimization and profitability of de-centralized energy production systems. Integration of energy storage systems in addition to decentralized renewable energy production, for example, by solar panels, leads to more effective electricity supply and smart energy solutions. The modelling of such complex dynamic system can be performed using system dynamics method. The aim of the article is to forecast the practice of electricity storage in Latvia in the coming decades. A system dynamics model predicting the implementation of battery storage in private households was created for the case study of Latvia. Modelling results reveal that under the right conditions for electricity price, investment costs and with the right policy interventions battery storage technologies combined with PV panels have high potential for utilization in household sector. Model results show that in baseline scenario with no additional policies up 21 422 households or 10.8 % of Latvian households could have combined PV and battery system installed in 2050. Moderate subsidy policy can help to increase this number up to 25 118.

In the laboratory practice, several standards for testing the bending stiffness of corrugated board are used. There are often cases of tests where the results depend on the way the sample is placed on the supports. The problem arises when the board is five-ply (with two corrugated layers with different corrugation heights) or when the board has asymmetrically selected papers on the flat layers. In this article, we focus our attention on the problem related to boundary conditions, with particular attention to the local effects of the support of the sample. Since the cardboard layers, both flat and corrugated, have a small thickness, a slight deformation of the papers can always be observed at the point of contact between the sample and the support, which affects the readings of the measured stiffness. The paper presents theoretical and numerical analyzes showing how much the method of supporting the sample affects the measured bending stiffness of various samples. Numerical observations were also compared with the results of analyzes presented by other scientists as well as with experimental results.

Respiratory tract infections (RTIs) are one of the main causes of hospitalization and mortality causing substantial economic burden to healthcare systems globally. As opposed to the previous belief that respiratory infections are caused by a single pathogen, studies have shown that most RTIs are a result of a combination of bacterial and/or viral pathogens infecting the host. The clinical manifestation of RTIs is very similar (i.e., syndrome), often showing Influenza-like illness (ILI) symptoms. While COVID-19 has dominated ILI over the past few years, there are many other pathogens that are responsible for ILI. In addition, it is not uncommon to have coinfections with multiple pathogens in patients presenting with ILI and that such coinfections can even exacerbate the disease severity of RTIs. Therefore, an insight into coinfections can help with accurate disease prognosis, patient care management and outcomes. The goal of this study was to identify the different organisms in symptomatic patients presenting with ILI.

The path towards decarbonization requires a progressive adaptation of all refrigeration systems, but only stationary ones have been intensely studied to improve their environmental performance. However, refrigerated transport is a vital piece of the cold chain, and it must be considered in the green transition. In this paper, we propose a model for a hybrid refrigerated van that includes photovoltaic panels and electric batteries to decrease total greenhouse gas emissions from the engine. Thermal, electrical, and battery sub-models are considered and integrated into the comprehensive hybrid solar-powered refrigerated van model. Different technologies are compared in economic terms, including Lithium and Lead-acid batteries and three different types of photovoltaic panels. The model was validated regarding van fuel consumption, showing a 4% deviation. Single and multiple delivery scenarios are considered to assess the energetic, economic, and environmental benefits. Monthly CO2,e emissions could be reduced to 20% compared to a standard refrigerated van. Despite the environmental benefits provided by this sustainable solution, the payback period is still too long (above 20 years) because of the necessary investment to adapt the vehicle and considering fuel and electricity prices currently.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

With the popularity of solar energy in the electricity market, demand arises for data such as precise locations of solar panels for efficient energy planning, management, and distribution. However, this data is not easily accessible and in some cases, information such as precise locations does not exist. Furthermore, existing data sets for training semantic segmentation models of PV installations are limited, and their annotation is time-consuming and labor-intensive. Therefore, for additional remote sensing (RS) data creation, the pix2pix generative adversarial network (GAN) is utilized, enriching the original resampled training data of varying GSDs without compromising its integrity. Experiments done with the DeepLabV3 model, ResNet-50 backbone, and pix2pix GAN architecture were conducted to find the optimal configuration for an accurate RS imagery segmentation model. The result is a fine-tuned solar panel semantic segmentation model, trained using transfer learning and utilizing an optimal amount – 60% of generated RS imagery for additional training data, increasing model accuracy. The findings demonstrate the benefits of using GAN-generated images as additional training data, increasing the size of small data sets, and improving the capabilities of the segmentation model for solar panel detection in RS images.

Analysis of complex DNA mixtures is limited by the selected genetic markers characterized and assay technology. Small panels of short tandem repeats (STRs) are the current standards in most countries. Extension of STRs with hundreds of single nucleotide polymorphisms (SNPs) is now commercially available. The current set of extension SNPs focus on phenotypic and biogeographic ancestry informative SNPs. Larger panels with thousands of SNPs have been developed that can identify up to 10 contributors to forensic DNA samples. Herein, multiple sets of SNPs were selected with the focus of increasing the upper limit of detectable contributors. Larger SNP panel sets with lower minor allele frequency (MAF) alleles can detect large numbers of contributors to in silico mixtures of randomly selected profiles from the 1,000 Genomes project. These results provide a path to enable characterization of complex DNA mixtures that are currently impossible to analyse.

This review paper explores the innovative realm of transparent solar panels, investigating their properties, applications, challenges, and recent advancements. Transparent solar panels, designed to harvest solar energy while allowing visible light to pass through, have gained significant attention due to their potential to revolutionize renewable energy technologies. The paper delves into the working mechanisms of various types of transparent solar panels, including Organic Photovoltaic (OPV) panels, Dye-Sensitized Solar Cells (DSSC), Perovskite Solar Cells, and Transparent Thin-Film Silicon Solar Cells. It discusses their integration into diverse applications, such as building-integrated photovoltaics, consumer electronics, the automotive industry, and aerospace. The review identifies challenges, including low efficiency, durability concerns, production costs, and integration hurdles, that currently hinder their widespread adoption. Moreover, the paper emphasizes the transformative potential of transparent solar panels in shaping the future of renewable energy, not only as energy generators but also as aesthetically pleasing and multifunctional components of our built environment. Finally, the paper underscores the need for continued research and development efforts to enhance efficiency, improve stability, and address integration challenges, paving the way for transparent solar panels to play a central role in the transition toward a more sustainable and energy-efficient future.

C-reactive protein (CRP) and leukocytes are blood biomarkers involved in "Inflamm-Aging", which is a risk factor for the onset and progression of age-related diseases. Studies show that higher serum concentrations of these biomarkers are associated with functional disability, increased risk of low muscle strength, decreased muscle mass and mortality in the elderly. The objective was to estimate the predictive power and discriminating criteria of C-reactive protein and leukocyte concentrations for the risk of adverse health factors in the elderly within 30 days after hospital discharge (HD). Prospective cohort study using exploratory methods and blood biomarkers with 135 older adults admitted to medical and surgical clinics at a government hospital. The elderly were monitored at home after 30 days of HD for adverse health factors (rehospitalization, falls, amount of medication consumed, disability in basic and instrumental activities of daily living and mortality). CRP> 2.4; ≥ 0.7 and> 24.7 mg / dL and leukocytes ≥ 6.410; ≥ 8.690 and> 8.310 mm³ were discriminant for rehospitalization, falls and mortality within 30 days after HD, respectively. The cut-off points described may be used as a reference in the screening of hospitalized elderly vulnerable to adverse health events after hospital discharge.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

This study investigates the effectiveness of a range of timber-based solutions for seismic and energy retrofitting of existing masonry buildings. These solutions are designed not only to prevent structural collapse during earthquakes but also to create integrated interventions that enhance thermo-physical performance and reduce emissions in existing buildings. Various case scenarios were considered and both mechanical and energetic behavior post-intervention were evaluated. Timber-engineered products serve as foundational components for the retrofit approach, encompassing one-dimensional vertical elements (strong-backs) and various types of panels (cross-laminated timber panels, laminated veneer lumber panels, and oriented strand board panels). The analyzed retrofit techniques share a common principle, involving the attachment of these timber-based elements to the building's wall surfaces through mechanical point-to-point connections. The proposed solutions integrate strong-backs and timber panels with membranes and insulation layers, yielding cohesive and highly effective interventions. Finite element modeling was employed to analyze the mechanical and thermal responses of the retrofitted walls. A comprehensive comparative analysis of various techniques was conducted to determine the most effective solution for each specific scenario.