This study involved a comprehensive examination of sensory attributes in Bísaro dry-cured loins, including odor, androsterone, scatol, color, fat color, hardness, juiciness, chewiness, flavor intensity, and flavor persistence. Analysis of 40 samples revealed a wide variation in these attributes, ensuring a robust margin for multivariate calibration purposes. The respective near-infrared (NIR) spectra unveil distinct peaks associated with significant components such as protein, lipid, and water. Support Vector Regression (SVR) models were methodically calibrated for all sensory attributes, with optimal results using multiplicative scattering correction pre-treatment, MinMax normalization, and radial base kernel (non-linear SVR model). The predictive models exhibited acceptable results, characterized by R-squared values close to 1 (0.9616 - 0.9955) and low RMSE values (0.0400 – 0.1031). The prediction set's relative standard deviation (RSD) remained under 5%. Comparisons with prior research revealed significant improvements in prediction accuracy, particularly when considering attributes like pig aroma, hardness, fat color, and flavor intensity. This research underscores the potential of advanced analytical techniques to improve the precision of sensory evaluations in food quality assessment.

This study analyzes the potential response of the seasonal cycle of heatwave (HWDI), dry (CDD) and wet (CWD) spells indices over West Africa for the near (2031-2060) and the far (2071-2100) future periods, under RCP4.5 and RCP8.5 scenarios using CORDEX simulations. Although some relative biases during the historical period (1976-2005), the CORDEX simulations and their ensemble mean outperform the seasonal variability of the above indices over three defined sub-regions of West Africa (i.e., Guinea gulf, west and east Sahel). They have shown significant correlation coefficients and less RMSE. They project an increase in heatwave days for both near and far future periods over whole west Africa region under both RCP scenarios. In addition, the Sahel regions will face to a decrease in wet spells days from March to November, whereas, the Gulf of Guinea will face to a decrease during all the year, except CCCLM simulation which indicates an increase during the retreat phase of the monsoon (October to December). The results also have shown an increase in dry spells over Sahel regions, more pronounced during March-November period, whereas, over Guinea gulf, the increase is observed over the entire year. On the other hand, the months of increasing dry spells and decreasing wet spells coincide, suggesting that countries in these regions could be exposed simultaneously to dry season associated with a high risk of drought and heatwave under future climate conditions.

(1) The present study investigated the effect of orally administered Limosilactobacillus fermentum HY7302 (HY7302) on the relationship between ocular tissue and the microbiome in the corneal injured dry eye mice model. (2) 0.1% benzalkonium chloride (BAC) was applied to the ocular surface for 14 days to induce corneal injury in male Balb/c mice. During the BAC treatment period, HY7302 (1 × 108 CFU/kg/day or 1 × 109 CFU/kg/day) or omega-3 positive control (200 mg/kg/day) were administered orally (n = 8/group). To examine signaling pathways affected by HY7302 treatment, the in vitro effects of HY7302 on tight junctions and the inflammatory response were investigated in a mouse colon epithelial cell line, CMT-93. (3) BAC exposure decreased tear production, induced ocular inflammation and corneal epithelial detachment, and altered gut microbiota. However, oral administration of HY7302 restored tear secretion and decreased corneal epithelial detachment in BAC-treated corneal injury mice. Further, HY7302 alleviated corneal inflammation via modulation of matrix metalloproteinase-9 (MMP-9) expression and alterations in gut microbiota composition. (4) These findings suggest that the gut–eye axis interaction between gut microbiota and eye tissue affects disease severity in corneal injury, and that alteration of the microbiota by HY7302 could improve eye health by regulating the inflammatory response.

The horizontal storm structure surrounding lightning ignited wildfires is examined using Vaisala’s National Lightning Detection Network (NLDN), NCEP’s Stage IV gauge corrected radar precipitation mosaic, and the US Forest Service’s Fire Occurrence Database. Though lightning flash density peaks strongly around fire ignitions on the instantaneous 1 km scale, on the hourly 10 km scale both the lightning and precipitation peaks are typically offset from fire ignitions. Lightning density is higher and precipitation lower around ignition points compared to non-ignition points. Both regression and horizontal distributions are consistent with the claim that positive flashes have a stronger association with ignition than negative flashes, but the statistical significance remains ambiguous

Abstract: Rotavirus (RV) it’s the agent of one of the main causes of severe viral gastroenteritis in the pediatric population, being responsible for a significant portion of deaths related to diarrhea among children under five years. RV are identified as a potential reference pathogen and it is known that the persistence and infectivity of the viral particles can be related to environmental factors. The aim of the study was to identify and correlate the presence of Rotavirus in collective and individual water sources (deep tubular wells, shallow tubular wells, shallow dug wells, springs, surface water, rainwater stored in cisterns and water trucks that were collected from surface water) of rural communities in the state of Goiás, with the seasons in which the collections were made (rainy and dry season). For this, 86 water samples in the dry period and 160 samples in the rainy period were collected. Concentration of water samples, extraction of viral genetic material, cDNA synthesis and molecular tests (qPCR) were performed. When analyzing the presence of RV in the samples in relation to the period studied, RV was found to be more prevalent in the dry season (54.7%) than in the rainy season (20%), showing a strong statistical association with the dry season (p-value < 0.001). The proportion of positive samples in the dry period, considering the type of source, resulted in higher in Shallow dug wells (p-value <0.001), higher in surface waters (p = 0.001) and higher in spring water (p-value = 0.02). The presence of pathogenic microorganisms in water is a public risk problem, enabling the emergence of outbreaks, endemics and epidemics. In the present research, there was an association among the presence of Rotavirus and the dry period of the year, when compared to the rainy period. Describing or identifying the seasonal behavior of pathogens is important for prevention and attention to water treatment and help in the monitoring of the virus in the water sources.

There is little information about moisture changes in different altitudinal belts in mountainous regions of the Southern Russian Far East. We present ecological-taxonomic composition of the diatom flora, the botanical composition of peat of small mountain lake/mire complexes located in the Central Sikhote-Alin within large landslides on the paleovolcano slopes are identified. Frequent changes in diatom assemblages and peat-forming plants indicate unstable hydroclimatic conditions with varying degrees of watering and dry condition up to complete overgrowth of the lakes. Frequent change of sphagnum mosses with different trophic preferences was established. The chronology is based on 11 radiocarbon dates. Accumulation rates reached up to 1.9 mm/year, the temporal resolution for the reconstructions is up to 30–40 years. The tendencies of lake evolution depended on different-scale hydroclimatic changes for the last 4400 yr. The most detailed data for the last 2600 yr were obtained from the Nizhnee Lake sequence, more sensitive to climatic changes. The main reason for the change in the hydrological regime of the lakes was variations in precipitation during short-term climatic changes. The sediment record moisture fluctuations are relatively well correlated with regional patterns reflecting summer monsoon intensity and cyclogenesis activity.

Beef dry aging consist in a selection of unpackaged primal cuts that are placed in a refrigerator room with controlled environment for several weeks. The goals are the concentration of flavor, like nutty and beefy and tenderness improvement. In this study it was intended verify the microbiological and physicochemical behavior and the meat sensorial perception during a process example of meat dry aging. Twelve beef loins were selected for 90 days of dry aging and placed in a refrigerator room with average temperature, relative humidity and forced air 3.17 ± 0.68 °C, 60.65 ± 4.23 % and 0.5-2 m/s, respectively. On 1, 14, 21, 35, 60 and 90 days of dry aging, were taken two samples, crust and lean meat for microbiological counts, pH, aw, color L*a*b* and sensorial analysis. During drying, there weren´t any pathogenic bacteria counts and the average counts were higher for the crust. The aw and pH had an average of 0.98 ± 0.02 and 5.77± 0.015, with a slightly decrease and increase respectively (P&lt;0.05) along aging days. The dry aging process practices, with room refrigeration at RH&lt;65.00% and temperature &lt;4.00 °C can be the reason for aw&lt;0.98 and meat pH&lt;6.00 and therefore for the absence of pathogenic bacteria. The lower microbial counts on the lean meat and the overall acceptability assessed by the sensory panel confirm the importance of the good trimming and storage practices for the dry aged beef.

The experiment was conducted to evaluate the effect of seed and fertilizer rates on biomass yield and other agronomic treats of two oat varieties (Bona-bas and Bate) at the Kuyu sub-site of Fitche Agricultural Research Center in 2022. Four levels of Nitrogen fertilizer rates (0, 23, 46, and 69 kg ha-1) and three levels of seed rates (60, 80, and 100 kg ha-1) with two oat varieties (Bona-bas and Bate) were using randomized complete block design in factorial arrangement with three replications. Soil samples before and after were collected and analyzed. The analysis of soil samples before planting indicated that the soil pH was strongly acidic (5.16) and after harvest, it raised to a strongly acidic level (5.29). The interaction effect of varieties, seed rates, and fertilizer rates showed highly significant (p<0.001) variation on the number of tillers per plant, leaf area per plant, leaf-to-stem ratio, fresh biomass yield, dry matter yield, days to maturity, and seed yield. The treatment combination of Bona-bas: FR46:SR100 has produced the highest dry matter yield (5.1 t/ha), followed by Bona-bas: FR46:SR60 and Bona-bas: FR69:SR80 which produced the same value of 4.9 t/ha dry matter yield. This study recommends that for the better agronomic performance of oat varieties, 46 kgha-1 N of fertilizer with 60 kgha-1 of seed rate is preferable to use by farmers in the study area and other areas having similar agroecologies and soil types. In addition, it is essential to conduct the year-over location to confirm the present findings and the result needs to be supported with animal evaluation trials.

Background: Cataract and Age-related Macular Degeneration are two characteristic diseases of the so-called elderly age (75-90 years and older). Both determine an important visual impairment, so it is often difficult to understand how much of the visual loss is given by the cataract opacities and how much by the degeneration of the macula and this assumes a relevant medico-legal query in clinical practice. Methods: From that pool we randomized in group 735 eyes with wAMD (males 328, females 407) Average age: 76.23±13.87 years, and in Group 819 eyes without clear signs of wAMD (males 361, females 451) Average age: was 75.88±18.21 years to randomize them we used the online randomization program (http://www.graphpad.com/quickcalcs/index.cfm) selecting random numbers and then randomly assign subjects to groups to undergo our observational study. All patients were examined with full ophtalmological visit including Best Corrected Visual Acuity (with Bailey-Lawson Chart), Anterior Segment examination, Fundus Examination, in all cases with wAMD was also performed OCT. ANOVA multifactorial statistical analysis was drawn. Results: number of patients with unsatisfactory surgery is significantly higher in the group of AMD patients, and this is easily understandable from what has been said above, but I would like to underline that in most patients there are very positive results, therefore cataract surgery is also indicated in AMD patients. Conclusions: Cataract surgery has a positive impact on the patient's life in most cases, you shouldn't be afraid to operate. However, it is necessary to find surgical measures capable of minimizing the consequences of the intervention on the retina.

This study aimed to develop a high-quality dry emulsion incorporating omega-3, 6, and 9 fatty acid-rich ostrich oil for use as a dietary supplement. Extracted from abdominal adipose tissues using a low-temperature wet rendering method, the ostrich oil exhibited antioxidant properties, favorable physicochemical properties, microbial counts, heavy metal levels, and fatty acid compositions, positioning it as a suitable candidate for an oil-in-water emulsion and subsequent formulation as a dry emulsion. Lecithin was employed as the emulsifier due to its safety and health benefits. The resulting emulsion, comprising 10% w/w lecithin and 10% w/w ostrich oil, was stable, with a droplet size of 3.93 ± 0.11 μm. This liquid emulsion underwent transformation into a dry emulsion to preserve the physicochemical stability of ostrich oil, utilizing Avicel® PH-101 or Aerosil® 200 through a granulation process. Although Aerosil® 200 exhibited superior adsorption, Avicel® PH-101 granules surpassed it in releasing the ostrich oil emulsion. Consequently, Avicel® PH-101 was selected as the preferred adsorbent for formulating the ostrich oil dry emulsion. The dry emulsion, encapsulated with a disintegration time of 3.11 ± 0.14 min for ease of swallowing, maintained microbial loads and heavy metal contents within acceptable limits. Presented as granules containing butylated hydroxytoluene, the dry emulsion showcased robust temperature stability, suggesting the potential incorporation of animal fat into dry emulsions as a promising dietary supplement.

Ultrasound is a well-known tool to produce thermal and non-thermal effects on cells and tissues. These effects require a correct application of ultrasound in terms of localization and acoustic energy delivered. This article describes a new device that combines ultrasound and Dry Needling treatments. The ultrasound transducer can rotate in 3D space mechanically to align itself in the direction of the needle. The transducer electronically focuses the acoustic pressure automatically on the needle tip and its surroundings. A computer, using graphical interface software, controls the angulation of the array and the focus position.

The study was conducted to evaluate the agronomic performance, forage yield, and nutritive values of Desho grass varieties under supplementary irrigation at Dambi Dollo University experimental site, Western Ethiopia. Three Desho grass varieties (Areka /DZF#590, Kindu kosha-1/DZF #591, and Kulumsa /DZF #592) were arranged in randomized complete block design (RCBD) with three replications. The CROPWAT 8.0 model, local climate data, forage data, and soil data were used to determine Desho grass water requirements and irrigation schedules. The agronomic parameters, yield, chemical composition, and in vitro digestibility of the feed samples at standardization cut were determined following the standard procedures. The results showed significant differences (p

A two-way coupled model between polydisperse particle phases with compressible gases and a density-based coupling implicit solution method combining the third-order MUSCL with QUICK spatial discretization scheme and the second-order temporal discretization scheme are constructed based on the discrete-phase model (DPM) and the stochastic wander model (DRWM) in the Eu-lerian-Lagrangian framework in conjunction with a unitary particulate source (PSIC) approach and the SST k-ω turbulence model. The accuracy of the numerical prediction method is verified using previous supersonic nozzle gas-solid two-phase flow experiments. Numerical simulation of two-phase jet of dry powder extinguishing agent gas with pilot-type supersonic nozzle was carried out to analyze the influence of geometrical parameters such as length ratio rL and area ratio rA of main nozzle on the two-phase flow field as well as on the jet performance indexes such as particle mean velocity vp,a, velocity inhomogeneity Φvp, particle dispersion Ψp, particle mean acceleration ap,a and so on. By analyzing the parameters, we indicate the requirements for the combination of jet performance metrics for different flame types such as penetrating, spreading, and dispersing.

This paper studies the evaporative heat transfer characteristics of R744 at low temperatures in a horizontal smooth tube as a cascade refrigeration system (CRS) among hybrid cascade refrigeration systems (HCRSs). There is a lack of research on the low-temperature evaporative heat transfer characteristics of R744 under the operating conditions of evaporators used in actual CRSs used in supermarkets. Therefore, this study aims to provide basic data on the evaporative heat transfer characteristics of R744 in the evaporators of refrigerators used in supermarkets. The tube used in the evaporation experiment conducted herein was a smooth horizontal copper tube with an inner diameter and length of 11.46 mm and 8000 mm, respectively. The experimental pa-rameters were as follows: heat fluxes of 12–21.5 kW/m2, mass fluxes of 75–225 kg/(m2·s), and saturation temperatures of −50–−30 °C. The main results are summarized as follows. (1) When designing the R744 evaporator, the mass and heat fluxes must be maximized within the operating conditions, and the saturation temperature must be designed to be as low as possible. (2) The evaporative heat transfer coefficient of R744 can be predicted well by using the correlation formula of Chen at the evaporation temperature of −40 °C in the CRS.

Protein malnutrition is present in developing countries but also in developed ones, due by the actual eating habits with insufficient protein intake, in addition to this it is estimated by the Food and Agricultural Organization of the United Nations an increase of world population of 9.1 billion people in less those 30 years, posing the challenge of nourish the mankind. There are different strategies to afford this challenge, one of the most promising ones is to approach novel protein sources like plants, microorganisms, and insects from dry lands.

Carbon fiber reinforced polymers (CFRPs) are being used extensively in modern industries that require high strength-to-weight ratio such as aerospace, automotive, motorsport, and sports equipment. However, although reinforcement with carbon fibers improves the mechanical properties of polymer, this comes on the expense of abrasive wear resistance. Therefore, to efficiently utilize CFRPs in dry sliding contacts, solid lubricant is used as a filler. Further, to facilitate fabrication of objects with complex geometries, selective laser sintering (SLS) can be employed. Accordingly, in the present work, graphite-filled carbon fiber-reinforced polyamide 12 (CFR-PA12) specimens were prepared using SLS process to explore the dry sliding friction and wear characteristics of the composite. The test specimens were aligned along four different orientations in the build chamber of SLS machine to determine the orientation-dependent tribological properties. The experiments were conducted using pin-on-disc tribometer to measure the coefficient of friction (COF), interface temperature, friction-induced noise, and specific wear rate. In addition, scanning electron microscopy (SEM) of tribo-surfaces was conducted to specify the dominant wear pattern. The results indicated that the steady state COF, contact temperature, and wear pattern of graphite-filled CFR-PA12 are orientation-independent, and that the contact temperature is likely to approach an asymptote far below the glass transition temperature of amorphous PA12 zones, thus eliminating the possibility of matrix softening. Additionally, the results showed that the Z-oriented specimen exhibits the lowest level of friction-induced noise along with the highest wear resistance. Moreover, SEM of tribo-surfaces determined that abrasive wear is the dominant wear pattern.

The aim of the study was to determine the effect of the application of different organic matter, UGmax soil conditioner and simplifications in potato cultivation on the content of dry matter, starch, sugars in tubers of the medium-early edible cultivar 'Satina' after harvest and after long-term storage. The highest dry matter (173.4 g kg-1) and starch (124.6 g kg-1 f. m.) content was ob-tained with the simultaneous application of a manure with soil conditioner at 100% mineral fer-tilization. In the case of sugars, the withdrawal of the soil conditioner from the crop proved most beneficial, for total sugars on the stubble intercrop (5.06 g kg-1 f. m.) and for reducing sug-ars (1.99 g kg-1 f. m.) on the straw. Each protection reduction applied resulted in a significant re-duction in starch content. In this regard, the withdrawal of herbicides with simultaneous appli-cation of manure and UGmax proved most beneficial. Long-term storage of tubers caused a sig-nificant reduction in their quality in terms of dry matter and starch content (average by -3.6 and -2.3%, respectively) and an increase in total and reducing sugars (average by 11.8 and 9.6%, re-spectively). The decrease in dry matter and starch content was significantly influenced by the 50% reduction in NPK fertilization applied during the growing season, while the application of soil conditioner with full protection contributed to the increase in reducing sugars after storage at 28.9 pts%. Our research is in line with current trends of used potato cultivation technologies focused mainly on environmental protection, so the results of this study can provide a basis for validation for researchers currently engaged in such evaluation.

We studied the capacity of glutathione and a specific inactivated dry yeast rich in glutathione to protect white grape must from browning compared to using sulphur dioxide. The results indicate that sulphur dioxide drastically reduces the oxygen consumption rate, protects hydroxycinnamic acids from oxidation and prevents grape must against browning even in the presence of laccase. Glutathione, pure or in the form of a specific inactivated dry yeast rich in glutathione, also reduces the oxygen consumption rate but to a lesser extent than sulphur dioxide. It favours the formation of GRP from hydroxycinnamic acids and effectively protects grape must against browning in healthy grape conditions. Nevertheless, in the presence of laccase it was not effective enough. Therefore, both forms of glutathione can be considered as interesting alternative tools to sulphur dioxide for preventing browning in white grape must, but only when the grapes are healthy.

The goal of this lab is to look at how the characteristics of cementitious materials are affected by bending loads combined with dry and wet cycles of sulfate. In this paper, three sets of specimens with different water–cement ratios were designed. This study applied 20% and 40% of the ultimate bending load as a continuous bending load to the cementitious material specimens for a sulfate erosion test. It was discovered that the specimens' porosity, flexural strength, and compressive strength all tended to improve initially before declining as the cementitious material was degraded in the sulfate solution aged. The flexural strength of the cementitious materials declined as the bending load increased, and their internal sulfate ion concentration rose. A transport model of sulfate ions in cementitious materials under the coupling effect of bending load and sulfate erosion was created by combining the improved version of Fick’s second law and chemical reaction kinetics. The simulation results show that the ion transport properties of sulfate ions in cementitious materials are in accordance with the experimental laws. These research results formed the basis of the unified standards for the coupling of load dry and wet cycle systems, as well as evaluating the durability of cementitious materials under corrosive environments.

In this study, vermiculite was explored as a support material for nickel catalysts in two key processes in syngas production through dry reforming of methane with CO2 and steam reforming of ethanol. The vermiculite was subjected to acid or base treatment, then, Ni catalysts were prepared through incipient wetness impregnation and characterized using various techniques, including X-ray, FTIR, temperature programmed reduction (H2-TPR). TG-TD analyses were performed to assess the formation of carbon deposits on spent catalysts. The Ni based catalysts were used in the reaction tests without a reduction pre-treatment. Initially, raw vermiculite-supported nickel showed limited catalytic activity, however after acid (Ni/VTA) or base (Ni/VTB) treatment, vermiculite became an effective support for nickel in dry methane reforming. The resulting catalysts (Ni/VTB and Ni/VTA) displayed outstanding performance, with high methane conversion and hydrogen yield. Acidic treatment improved the reduction of nickel species and reduced carbon deposition, outperforming alkali treatment. The prepared catalysts were also explored in ethanol steam reforming. The performance was investigated as a function of the temperature, water/ethanol ratio, and space velocity, with acid-treated catalysts performing as the best. The study emphasized the importance of contact time with the catalyst and addressed challenges related to carbon formation and sintering for long-term stability. In conclusion, acidic treatment of the vermiculite support, before Ni deposition, significantly enhanced the catalytic activity and stability of nickel catalysts in both dry methane reforming and ethanol steam reforming processes.

This study aims to assess the interface shear adhesion behaviour between compacted clay and a metallic surface. A new testing approach was developed in this study for this purpose. The proposed method is simple and requires neither advanced equipment nor special test procedures, and thus represents an improvement on existing practice in this field. The experimental program involves determining the interface shear adhesion strength of reconstituted Kaolin clay/metallic surface where the Kaolin clay testing specimens were compacted dynamically at different energy levels and moisture contents. In general, the results show that the interface shear adhesion strength increases as the dry density of the clay increases, whereas it decreases as the moisture content increases. Furthermore, the results in this study reveal a unique multistage interfacial shear adhesion strength behaviour as the moisture content changes that could be related to the compaction curve of the clay. The observed behaviour, in this study, could be interpreted in terms of the effect of clay dry density and moisture content on the contact area and moisture-induced capillary adhesion at clay particles-continuum interface surface.

This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

Purpose: To evaluate the relationship between corneal nerve structure and function in a veteran population. Methods: 83 veterans (mean age: 55 ± 5 years) seen at the Miami Veterans Affairs (VA) eye clinic were included in the study. Each individual filled out questionnaires to evaluate ocular symptoms (5-Item Dry Eye Questionnaire, DEQ5, Ocular Surface Disease Index, OSDI) and ocular pain (Numerical Rating Scale, NRS, Neuropathic Pain Symptom Inventory modified for the Eye, NPSI-Eye). Individuals also underwent an ocular surface examination that captured functional nerve tests including corneal sensation, corneal staining, and Schirmer test for tear production. Corneal sub-basal nerve analysis was conducted using in vivo confocal microscopy (IVCM) images with corneal nerve density, length, area, width, and fractal dimension captured. IVCM and functional corneal metrics from the right eye were examined using correlational and linear regression analysis. Results: Most corneal structural metrics were not related to functional metrics, except for weak correlations between various IVCM metrics and tear production. In addition, corneal nerve fiber area was positively related to corneal sensation (r = 0.3, p = 0.01). On linear regression analyses, only corneal fractal dimension remained significantly related to tear production (β = -0.26, p = 0.02) and only corneal nerve fiber area remained significantly related to corneal sensation (β = 0.3, p = 0.01). Conclusions: Most corneal nerve structural metrics did not relate to functional metrics in our veteran population, apart from a few weak correlations between structural metrics and tear production. This highlights caution in using corneal nerve anatomy to predict corneal function.

There is little doubt that final victories over pandemics, such as COVID-19, are attributed to herd immunity, either through post-disease convalescence or active immunization of a high percentage of the world's population with vaccines, demonstrating protection from infection and transmission, being available in large quantities and at reasonable prices. However, it is assumable that humans with immune defects or immune suppression, e.g., as a consequence of allograft transplantation, cannot be immunized actively nor produce sufficient immune responses to prevent SARS-CoV-2 infections. These subjects desperately need other strategies, such as sophisticated protection measures and active immunization. Hypertonic salt solutions attack vulnerable core areas of viruses, i.e., salt denatures surface proteins and thus prohibits virus penetration of somatic cells. It has to be ensured that somatic proteins are not affected by denaturation regarding this unspecific virus protection. Impregnating filtering facepieces with hypertonic salt solutions is a straightforward way to inactivate viruses and other potential pathogens. As a result of the contact of salt crystals on the filtering facepiece, these pathogens become denatured and inactivated almost quantitatively. Such a strategy could be easily applied to fight against the COVID-19 pandemic and other ones that may occur in the future. Another possible tool to fight the COVID-19 pandemic is passive immunization with antibodies against SARS-CoV-2, preferably from human origin. Such antibodies can be harvested from patients´ human sera, which have successfully survived their SARS-CoV-2 infection. The disadvantage of a rapid decrease of the immunoglobulin titer after infection ends can be overcome by immortalizing antibody-producing B-cells via fusion with, e.g., mouse myeloma cells. The resulting monoclonal antibodies are then of human origin and available in, at least theoretically, unlimited amounts. Finally, dry blood spots are a valuable tool for surveilling the population´s immunity.

Leaf mass per area (LMA) is a key structural parameter that reflects the functional traits of leaves and plays a vital role in simulating the material and energy cycle of plant ecosystems. In this study, vertical whorl-by-whorl sampling of LMA was conducted in a young Larix principis-rupprechtii plantation during the growing season at the Saihanba Forest Farm. The vertical and seasonal variations in LMA were analysed. Subsequently, a predictive model of LMA was constructed. The results revealed that the LMA varied significantly between different crown whorls and growing periods. In the vertical direction of the crown, the LMA decreased with increasing crown depth, but the range of LMA values from the tree top to the bottom was, on average, 30.4 g/m2, which was approximately 2.5 times greater in the fully expanded phase than in the early leaf-expanding phase. The LMA exhibited an allometric growth trend that increased during the leaf-expanding phase and then tended to stabilize. However, the range of LMA values throughout the growing period was, on average, 40.4 g/m2. Among the univariate models, the leaf dry matter content (LDMC) performed well (Ra2=0.45, RMSE=13.48 g/m2) in estimating the LMA. The correlation between LMA and LDMC significantly differed at different growth stages and at different vertical crown whorls. The dynamic predictive model of LMA constructed with the RDINC and DOY as independent variables was reliable in both the assessments (Ra2=0.68, RMSE=10.25 g/m2) and the validation (MAE=8.05 g/m2, FI=0.682). Dynamic simulations of crown LMA provide a basis for elucidating the mechanism of crown development and laying the foundation for the construction of an ecological process model..

Abstract: Microflora play an important role in the fermentation of blueberry wine, influencing the flavor and nutrient formation. Commercial yeasts give blueberry wines an average flavor profile that does not highlight the specific aroma and origin of the blueberry. In the present study, ITS1-ITS2 region sequencing analysis was performed using Illumina MiSeq high-throughput technology to sequence fermented blueberry wine samples of three Vaccinium ashei varieties, Gardenblue, Powderblue, and Britewell, from the Majiang appellation in Guizhou province to analyze the trends of fungal communities and the diversity of compositional structures in different periods of blueberry wine fermentation. The study's results revealed that 114 genera from 7 phyla were detected in 9 samples from different fermentation periods of blueberry wine. The main fungal phyla were Ascomycota, Basidiomycota, Kickxellomycota, Chytridiomycota, and Olpidiomycota. The main fungal genera were Hanseniaspora, Saccharomyces, unidentified, Aureobasidium, Penicillium, Mortierella, Colletotrichum, etc. Hanseniaspora was dominant in the pre-fermentation stage of blueberry wine, accounting for more than 82%; Saccharomyces was the dominant genera in the middle and late fermentation stages of blueberry wine, with Saccharomyces accounting for more than 72% in the middle of fermentation and 93% in the late fermentation stage. This study screened indigenous flora for the natural fermentation of blueberry wine in the Majiang production area of Guizhou, improved the flavor substances of the blueberry wine, highlighted the characteristics of the production area, and made the blueberry wine have the characteristic flavor of the production area.

Fourteen Russian potato cultivars (cvs.) grown for three years in field plots of VIR (Northwestern region of the Russian Federation) were evaluated for productivity and a number of biochemical parameters of tubers. The 12 parameters that have been evaluated in tubers annually one month after harvesting and after cold storage (at 2 - 4°C) include the content of dry matter, starch, protein, ascorbic acid, carotenoids and β-carotene, anthocyanins, total sugars and monosaccharides (reducing sugars), phenolic compounds, as well as total acidity, and antioxidant activity. The cultivars differed significantly in productivity and biochemical composition of tubers. Dry matter content ranged from 16.40% in cv. ʻKumachʼ to 27.28% in ʻNayadaʼ, starch content ranged from 8.96 % in cvs. ʻFioletovyjʼ, ʻKumachʼ to 20.08% in ‘Sokur’, the total sugar content reached 2.46% in cv. ʻSiverskij’ whereas ‘Sokur’ has the smallest content of reducing sugars in post-harvest tubers. Protein content ranged from 1.02% to 2.77% with the highest accumulation in cv. ʻSokurʼ. Content of ascorbic acid (vitamin C) ranged from 6.3 mg/100 g FW in ʻKrasa Meŝeryʼ to 26.6 mg/100 g FW in cv. ʻKrasavchikʼ. Carotenoids content ranged from 0.157 mg/100 g FW in cv. ‘Nayada’ to 0.645 mg/100 g FW in cv. ʻGrandʼ. Content of anthocyanins in potato ranged from 1.04 mg/100g FW (not colored tubers of cv. ʻKrasa Meŝeryʼ) to 283.04 mg/100g FW (colored tubers of cv. ʻFioletovyiʼ). The nutritional value of tubers (content of dry matter, sugars, starch and protein) was determined to a greater extent (38-49%) by varietal characteristics, rather than by meteorological conditions in vegetation period. The content of vitamin C, carotenoids, protein and anthocyanins varied depending on the year. The highest content of dry matter, starch and carotenoids was noted in tubers harvested in 2019, marked by low temperatures and precipitation deficit in growing season. The conditions of 2020 with low temperatures and excess precipitation were the most favorable for anthocyanin’s accumulation in potato tubers while not for other biochemical parameters. Of the cultivars, ʻSokurʼ had the highest content of dry matter, protein and starch. Cv. ʻFioletovyiʼ had small starch content and high level of anthocyanins. Cv. ʻPlamyaʼ can be recommended for potato products manufacturing due to dry matter content above 20% and reducing sugars content 0.24%..

Under the dual erosion conditions of the dry-wet cycle, which is caused by the high chloride salt concentrations in mine water and fluctuations in mine water level, cemented paste backfill (CPB) suffers serious damage and deterioration. To discuss the mechanical properties and permeability characteristics of CPB under erosion, this study designs an immersion experiment for CPB under chloride salt and dry-wet cycle conditions. Through a uniaxial compressive strength (UCS) test, the change law for the mechanical parameters of the CPB was explored, strength constitutive equation of the CPB was constructed, and the process of deterioration of the CPB was analyzed. Through the penetration test, the diffusion characteristics of packing under chloride salt and dry-wet cycle conditions were explored. The results demonstrated that the strength and elastic modulus of the CPB first increased and then decreased rapidly, with maximum decrease rates of 32.2% and 38.2%, respectively. The CPB structure presents an initial non-damage stage, initial damage stage, damage development stage, damage destruction, and residual damage stage. The chloride ion penetration depth gradually increased with an increase in the number of dry-wet cycles, with a maximum diffusion depth of 20.5 mm. The maximum apparent diffusion coefficient of chloride ion was 18.99×10-10m2/s, and the maximum concentration was 0.303 mol/L. Under the double erosion conditions due to chloride salt and dry-wet cycle, the CPB structure is seriously damaged.

With the application of high-precision, enormous rotating equipment and the addition of harsh working conditions, the advantages of dry gas sealing technology are increasingly obvious. Herein, research on the dynamic stability of dry gas seals is reviewed based on their operating mechanism. The influence of the dry gas seal structure, vibration response, and dynamic followability on the reliability of the shaft end sealing system of rotating machinery is the focus of current dry gas sealing technology. This work reviews the research history; analyzes the key coefficient of instability of the sealing system under external disturbances and the existing research on stability models; discusses the influence of starting and stopping characteristics, working conditions, and groove parameters on the stability of dry gas seals; and points out the shortcomings in the existing research. In addition, potential developments in dynamic stability are proposed, including improving model accuracy, improving experimental techniques, or applying intelligent control and optimization methods to enhance the dynamic stability of the sealing system. Finally, the development prospects for dry gas sealing technology in intelligent monitoring and wide temperature range adaptations are discussed, and theoretical guidance for improving the dry gas seal system is provided.

The heat generated during the startup process of dry gas seals, such as the friction heat of the asperities, viscous shear heat, and the expansion heat of the gas film, easily leads to seal failure and endangers the stable operation of turbomachinery. This study combines the statistically modified contact model and the average Reynolds equation by considering the adiabatic index and the microscale effects of dry gas seals to explore the heat generation characteristics of dry gas seals formed in series at multiple times. In particular, the change laws and influencing factors among the components, including the friction heat of asperities and the shear heat and expansion heat of the gas film and total heat, are investigated. A comparative analysis indicates that the slip flow effect increases the total heat during the startup process. The friction heat is much greater than expansion heat and shear heat. Despite constant acceleration, exponential acceleration, or Harrision acceleration, the heat changes are uneven during the startup process. In particular, the heat changes sharply in the early stage and gently in the later stage. The Harrision acceleration mode is the most conducive to sealing stability.

The focus of our study was the changes in the composition of semi-natural dry grasslands in Hungary. Since these valuable habitats were created with the help of humans, their preservation also requires regular treatment. Our mowing experiment aimed to investigate the suppression of the native Calamagrostis epigejos L. Roth. In Hungary, in the Cserhát Mountains, eight permanent plots were mowed twice a year. The vegetation was sampled annually between 2001 and 2011. The effects of mowing were investigated with repeated measures analysis of variance (ANOVA). After 10 years, the C. epigejos cover of the mowed plots decreased significantly, from the initial average of 62.38 to 7.50%. Surprisingly, we also experienced a similar decrease in the control plots. Regular treatment also had a positive effect on the number of species and diversity. Species richness increased continuously in both treatment types, which indicates the combined effect of vegetation succession and treatment. The biomass growth of other Poaceae and Fabaceae species, which are important from a grassland management perspective, was also facilitated by mowing. Our results suggest that long-term in situ experiments and continuous botanical studies are needed to establish a reliable utilization of grasslands.

This paper aims to study the performance of solar collectors with various sizes under different weather conditions of different Japanese cities, i.e. Kofu city, Nagoya city and Yamagata city. The heat generated from the solar collector was used to conduct a biogas dry reforming reactor in order to produce H2 to feed a solid oxide fuel cell (SOFC). This study has revealed that the output temperature of solar collector, Tfb in April and July was higher than that in January and October irrespective of city. The optimum length of absorber (dx) of the collector was 4 m irrespective of city. It was clarified that Tfb in Yamagata city in January and October, i.e. winter and autumn is lower than that in Kofu city and Nagoya city especially, which is influenced by the tendency of a solar intensity (I) strongly, not velocity of surrounding air (ua). On the other hand, Tfb is almost the same in April and July, i.e. spring and summer, irrespective of city. The amount of produced H2 from the biogas dry reforming reactor and the power generated by SOFC using H2 in spring and summer were higher compared to the other seasons irrespective of city. This study has revealed that the highest available households number per month was 4.7 according to the investigation in this study.

The aim of this study is to present the spatial and temporal variability of the frequency of dry and wet days and dry and wet spells against the background of changes in precipitation and atmospheric circulation. The study is based on daily precipitation totals from 46 meteorological stations in Poland for the years 1966-2023. Additionally seven circulation indices were used: GBI, NAO, AO, EA, EA/WR. SCAND ana AMO. Dry days are defined as days without precipitation. Wet days are days with at least 1 mm of precipitation. It was shown that dry spells are much more common that wet spells, are longer and cover larger areas. Long term changes in annual characteristics of dry and wet days and spells are statistically insignificant. Only the length of the longest dry spell in the year increases. However, there are significant changes in their annual cycles. Spring is drier, in summer months, precipitation decreases in the south and increases in the north, November and December, symbols of gloomy rainy weather, are increasingly drier, rainy weather moved to January and February. The impact of circulation varies with seasons and NAO, Ao, SCAN and GBI indices have the strongest impact.

The effect of H2S with high concentrations on catalytic dry reforming of methane (DRM) process has seldom been focused on previously. Herein, a thermodynamic analysis of the DRM reactions in the presence of H2S with the concentration varying in 0-20 vol% was conducted firstly. Several typical types of catalysts including MgO, NiO/MgO and LaNiO3 in different states were prepared for executing DRM at 800 C, 0.1 MPa in the feed of 20 vol% CO2 and 20 vol% CH4 balanced with N2. The catalytic performance of each catalyst for DRM process under conditions of absence and presence of H2S was compared. A promotion effect of increasing H2S concentration on both the conversions of CO2 and CH4 and the molar yields of CO and H2 was observed on all the catalysts especially the MgO and the pristine NiO/MgO. While a significant decline in catalytic activity of either the reduced NiO/MgO or the reduced LaNiO3 catalyst after adding H2S, moderate reactant conversions still sustained. The results of process analysis and catalyst structure characterization suggest that H2S participation can contribute to the increment in CO2 and CH4 conversion, and active S-adsorbed species may play the key role of catalysis in the reactions involving H2S.

This study investigated the adaptability of Dunaliella salina to different salinity levels, with emphasis on growth, pigment concentration, and desalination potential. It was found that among the 21 salinity levels (0-20%), 75‰ salinity produced consistently favorable results in cell count (13.08 x 103 ± 1.41 x 103 cells/mL), dry biomass (2.46 ± 0.06 g/L), pigment content (chlorophyll a = 9.75 ± 0.01 µg/L, chlorophyll b = 12.36 ± 0.03 µg/L), and desalination (9.32 ± 0.47 % reduction). Therefore, 75‰ salinity level was selected for the final trial (scale-up), which revealed unanticipatedly high cell counts (58.96 x 103 ± 535.22 cells/mL), with dry biomass weight being statistically extremely different (higher) than the expected (4.21 ± 0.02 g/L) (p&lt;0.0001), most likely due to high cell count and energy reserve storage for high salinity adaption in the form of bio-compounds. Pigment growth continued (chlorophyll a = 9.54 ± 0.2 µg/L, chlorophyll b = 12.81 ± 0.51 µg/L), indicating pigment production under salt stress. Notably, desalination did not occur in this stage, possibly due to the necessity for a bigger initial inoculate, prolonged exposure or bioaccumulation becoming the prevailing mechanism over desalination. Despite this, the microalgae thrived in high salinity conditions. These findings point to further study into the mechanics of salt build-up within cells, which might lead to successful desalination technologies. Dunaliella salina adaptation to high salinity settings suggests its possible usage in natural pools or soils that are normally inappropriate for traditional production, giving a chance for enterprises to function in rough extreme salinity conditions.

This study proposed the combination system consisting of biogas dry reforming reactor and solid oxide fuel cell (SOFC). Since a biogas dry reforming is an endothermic reaction, this study adopted a membrane reactor operated due to the non-equilibrium state with H2 separation from the reaction space. This study aimed to clarify the characteristics of Ni/Cr/Ru catalyst using for a biogas dry reforming membrane reactor. Additionally, this study also investigated the comparison of the characteristics of Ni/Cr/Ru catalyst with that of Ni/Cr catalyst. The impact of operation temperature, the molar ratio of CH4 : CO2, the differential pressure between the reaction chamber and the sweep chamber and the introduction of sweep gas on the characteristics of the biogas dry reforming membrane reactor using Pd/Cu membrane and Ni/Cr/Ru catalyst was examined. The concentration of H2 using Ni/Cr/Ru catalyst was larger than that using Ni/Cr catalyst by 2871 ppmV for the molar ratio of CH4 : CO2 = 1.5 : 1 at the reaction temperature of 600 ℃ and the differential pressure of 0 MPa without a sweep gas, especially. Under this condition, CH4 conversion, H2 yield and thermal efficiency were 67.4 %, 1.77×10-2 % and 0.241 %, respectively.

Despite its growing importance as a dry beneficiation method, there is a lack of studies exploring the fundamentals aspects of dry jigging. In this sense, this study focuses on explore some essential aspects of density-based separation in dry jigs, like pulse profile, energy consumption and, especially, stratification over time, also exploring an innovative operational strategy here called “transient pulsation”. The tests were carried out using density tracers distributed across 11 density ranges (0.4-2.4 g/cm³) and employing a base bed (gravel) to analyze their segregation in a pilot-scale dry jig. Pressure drop and active power data were acquired to measure the pulse characteristics and energy consumption. The findings suggest that establishing the dry jigging cycle is more complex than in hydraulic jigs due to the compressibility of air. Stationary pulsation tests revealed an unstable behavior of stratification over time, contrasting with traditional hydraulic jigs, while transient pulsation tests unveiled varied trends in separation quality. Energy consumption analysis underscored the significant role of the blower drive. These insights have the potential to inform operational enhancements in dry jigging.

Predictive factors associated with a decline in swallowing function after 2 years were examined in 3,409 Japanese older people aged ≥ 75 years who had undergone a dental checkup in Gifu Prefecture, Japan. Participants with normal swallowing function in a baseline survey in April 2018 were followed for 2 years. Swallowing function was assessed by a repetitive saliva swallowing test. After 2 years, 429 participants (13%) who could not swallow at least three times in 30 seconds were diagnosed as having a decline in swallowing function. Multivariate logistic regression analyses showed the decline in swallowing function after 2 years was associated with male gender (odds ratio [ORs]: 0.772; 95% confidence interval [CIs]: 0.615–0.969), age ≥ 81 years (presence; ORs: 1.523; 95% CIs: 1.224–1.895), support/care-need certification (presence; ORs: 1.815; 95% CIs: 1.361–2.394), periodontal pocket depth (PPD) ≥ 4 mm (presence; ORs: 1.469; 95% CIs: 1.163–1.856), difficulty in biting hard food (yes; ORs: 1.439; 95% CIs: 1.145–1.808), choking on tea and water (yes; ORs: 2.543; 95% CIs: 2.025–3.193), and dry mouth (yes; ORs: 1.316; 95% CIs: 1.052–1.646) at baseline. Therefore, the dental checkup items associated with a decline in swallowing function after 2 years were a PPD ≥ 4 mm, difficulty in biting hard food, choking on tea and water, and dry mouth. PPD status and confirming to the self-administered questionnaire about biting, choking, and dry mouth may be useful in predicting future decline in swallowing function.

Gabapentin (GBP) was originally developed as a potential agonist for Gamma-Amino-Butyric-Acid (GABA) receptors, aiming to inhibit the activation of pain-signaling neurons. Contrary to initial expectations, it does not bind to GABA receptors. Instead, it exhibits several distinct pharmacological activities, including: (1) binding to the alpha-2-delta protein subunit of voltage-gated calcium channels in the central nervous system, thereby blocking the excitatory influx of calcium; (2) reducing the expression and phosphorylation of CaMKII via modulation of ERK1/2 phosphorylation; (3) inhibiting glutamate release and interfering with the activation of NMDA receptors; (4) enhancing GABA synthesis; (5) increasing cell-surface expression of δGABA_A receptors, contributing to its antinociceptive, anticonvulsant, and anxiolytic-like effects. Additionally, GBP displays (6) inhibition of NF-kB activation and subsequent production of inflammatory cytokines, and (7) stimulation of the purinergic adenosine A1 receptor, which supports its anti-inflammatory and wound-healing properties. Initially approved for treating seizures and postherpetic neuralgia, GBP is now broadly used for various conditions, including psychiatric disorders, acute and chronic neuropathic pain, and sleep disturbances. Recently, as an eye drop formulation, it has also been explored as a therapeutic option for ocular surface discomfort in conditions such as dry eye, neurotrophic keratitis, corneal ulcers, and neuropathic ocular pain. This review aims to summarize the evidence supporting the molecular effects of GBP, with a special emphasis on its applications in ocular surface diseases.