The synergistic effect of silicon and cerium addition on the oxidation resistance of pack cementation aluminide coating applied on Ni-based superalloy substrate was investigated. The effect of cerium and silicon on the scale morphology, oxidation behavior, and scale spallation tendency are discussed based on the experimental results, using X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray analyses (EDX). In addition, the oxidation resistance was evaluated by measuring the weight of samples after each 16-hour cycle at 1100˚C for 50 cycles. The experiments indicated that silicon addition to aluminide coating improves the oxidation resistance through the formation of β-NiAl1-nSin and δ-Ni2Al3-nSin and δ-Ni2Si phases. Furthermore, the addition of 1% cerium to modified aluminide enhances the formation of the fine-grained microstructure of the β-NiAl and δ-Ni2Al3 and reduces the outward/inward diffusion of elements (so-called blocking effect) which significantly modifies the hot oxidation resistance. The addition of 2% cerium, owing to the distortion of the β-NiAl and δ-Ni2Al3 phases, strictly decreases the hot oxidation resistance and the coating is exfoliated after 450 h at 1100 °C. The cyclic oxidation tests showed that the samples containing 1% cerium and 6% silicon possess the highest hot oxidation resistance in which 2 mg/cm2 weight loss of Ce-Si-aluminide was reported after 800 h. This is attributed to the simultaneous effect of cerium and silicon during the deposition process which reduces the oxygen diffusion and reduces the growth rate of α-Al2O3 during oxidation tests. The α-Al2O3 oxidation layer morphology showed that finer grains are formed in samples containing optimum ratios of cerium and silicon which indicates that these elements improve the coating adhesion and oxidation resistance simultaneously.

This paper concerns the effect of proppant embedment related with hydraulic fracturing treatment. This phenomenon occurs if the strength of the reservoir rock is lower than proppant grains. The aim of the research is laboratory determining the loss of width of the proppant pack built of light ceramic grains. The laboratory simulation of the embedment phenomenon was carried out for a shale rock on a hydraulic press, in a specially prepared for this purpose a heated embedment chamber. Tests were conducted at high temperature and axial compressive stress conditions. The surfaces of the cylindrical core plugs (fracture faces) were imaged under an optical microscope equipped with 3D software. The fracture faces were examined and compared before and after the embedment phenomenon. The analysis of the obtained images of the fracture face were made based on the research method of the embedment phenomenon developed at Oil and Gas Institute-NRI. On the basis of laboratory tests, the parameters characterizing the embedment phenomenon were collected and discussed. In addition, the percentage reduction in the width of the proppant pack was determined.

This scoping review investigated how consumers perceive and interpret serving size information on food packages. A search of seven databases (2010 to September 2017) was followed by title and abstract screening, with relevant articles assessed for eligibility in full-text. Fourteen studies met inclusion criteria, with relevant data extracted by one reviewer and checked for consistency by a second reviewer. Five studies reported poor understanding of nutrition facts labelling and portion size, with information to ‘benchmark’ serving size against reported as helpful in two studies. Consumer attitudes towards serving size labelling were measured in six studies and identified that serving size information was interpreted as indicative of nutrient intake regardless of portion size recommendations. Increased labelled serving sizes resulted in increased portion sizes in three studies, with three studies reporting the opposite or neutral effect for discretionary food portion sizes. The influence of labelled serving size on consumer attitudes and consumption is complex and sometimes counterintuitive. As labelled serving size can impact on consumption, any changes may result in unintended public health consequences. The effects of labelled serving size format changes should be tested carefully within experimental and ecological contexts and accompanied by tailored, comprehensive and serving size-specific food literacy initiatives.

Universitas Sebelas Maret (UNS) through SMART UNS Company has conducted research and development of e-motorcycle conversion using Li-ion battery pack as a substitute for ICE energy source from the conventional motorcycle. Currently, the battery-pack that used for e-motorcycle conversion is in the development phase towards commercialization. The challenge of estimating production costs is the complicated production process and storing hidden expenses that can be a problem. This hidden cost is often a missing or varied factor that costs less or more expensive. This study presents an integrated parametric cost estimation model with activity-based cost assignments to estimate production costs through cost calculations for each activity. Activity-based costs break the production process into a specific cost element for each step. Each activity's cost is put into a parametric cost estimation model to calculate the cost of each activity into the total cost of production. Cost estimation results will be analyzed using a regression method to determine which variables most affect the production cost of Li-ion battery packs for the conversion of e-motorcycles in the SMART UNS company.

During the development of horizontal wells in bottom water reservoirs, the strong heterogeneity of reservoir permeability leads to premature bottom water breakthrough at locations with high permeability in the horizontal wellbore, and the water content rises rapidly, which seriously affects production. In order to cope with this problem, a new technology has emerged in recent years that utilizes gravel filling to block the flow in the annulus between the horizontal well and the borehole, and utilizes the Inflow Control Device (ICD) completion tool to carry out segmental water control in horizontal wells. Unlike conventional horizontal well ICD completions that use packers for segmentation, gravel pack combined with ICD completions breaks the original seg-mentation routine and increases the complexity of production dynamic simulation. In this paper, the flow in different spatial dimensions such as reservoir, gravel packed layer, ICD completion section and horizontal wellbore is modeled separately, and the annular pressure at different locations is used as the solution variable for the coupled solution, which realizes the prediction of oil production, water production and water content of gravel pack combined with ICD completions of horizontal wells. The model was used to calculate the effects of different crude oil viscosities, different reservoir permeabilities, different permeabilities of gravel packed layers, and different development stages on the water control effects of gravel pack combined ICD completions and conventional ICD completions at field conditions. This study provides a basis for using gravel pack combined ICD completions in horizontal wells in bottom water reservoirs.

Background: Front-of-package labelling (FoPL) is shown to be effective in assisting consumers make healthier food choices. Several countries are implementing various types of FoPL systems. Objective: This study explored consumers’ perceptions and understanding of three different FoPLs and their insights into features that could influence the effectiveness of the symbols in Kenya Methods: A qualitative study was conducted in four Counties in Kenya; Nairobi, Mombasa, Garissa, and Kisumu. Data was collected through twelve focus group discussions with 137 adults drawn from diverse socio-demographic and socio-economic backgrounds. Three FoPLs were assessed: Red and Green (RG) Octagon, Red and Green Octagon with icons and text (RGI), and the Black Octagon Warning label (WL). The FGDs explored participants’ perceptions of the symbols’ visibility and memorability, their understanding, potential effectiveness, and cultural appropriateness. Printed images displaying four different commonly consumed products bearing specific FoPLs were used during data collection. Data was analyzed thematically and organized using NVivo version 14.0. Results: Results showed that Kenyan consumers had varied perceptions about the proposed FoPL symbols. Majority of the participants found the black Octagon WL to be most visible and memorable due to its good blend of black and white colours. Although the RG octagon symbol and RGI octagon symbols were also found to be eye-catching due to their bright colours, it emerged that the different colours often confused some participants on their meaning. Most participants understood the WL compared to the RG and RGI because they found the additional text more educative. Generally, the WL was preferred as the symbol most likely to influence consumer purchase behaviours and food consumption. All the three FoPLs tested were found to be culturally appropriate. Conclusions: The Black Octagon Warning Label is the most easily visible and understood among the three FoPLs tested and has the potential to influence purchase and consumption behaviours among Kenyan consumers. Although the RG and RGI symbols are visually appealing to many, confusion related to different colours could affect their effectiveness. Consumers need to be educated on the use of FoPLs to ensure they discourage the purchase and consumption of unhealthy foods.

The main challenge in milk production has been to maintain a focus on efficient processes that enhance production outcomes, while aligning with animal welfare and sustainability and being valued by society. As an alternative to improve cow welfare in production and provide better handling of the waste generated by the activity, the system called compost-bedded pack barn (CBP) is an alternative that has been widely adopted in countries with temperate climates and higher milk production. This CBP has been attracting global interest, including from countries with tropical and subtropical climates, such as Brazil, where many producers have started to use it due to the response in terms of milk productivity. A CBP can be designed either in a) an open facility with natural ventilation or positive pressure ventilation system or b) totally closed facilities, equipped with negative pressure ventilation systems and permanent thermal control. The latter system is being implemented in Brazil, despite insufficient knowledge about its efficiency. The objective of this study was, through a review, to gather and describe the most recent information on the use of open and closed CBP systems for dairy cattle housing, mainly how it is applied in tropical climate regions. To achieve the proposed objective, this review study included the following topics related to CBPs: (i) implementation; (ii) bedding; (iii) general construction and architectural characteristics; iv) ambient thermal conditioning. Knowledge gaps and directions for future research are also identified.

Abstract: An Al-Co-Y diffusion coating was prepared on a TiAl alloy by pack cementation process at a low temperature range of 650-720 ℃. The influence of different activators and co-deposition temperatures on the coating’s microstructure and formation process, and high temperature oxida-tion performance was studied. The results showed that NaF was a more suitable activator for preparing the Al-Co-Y diffusion coating on TiAl alloy compared to NH4Cl and AlCl3. A more compact coating structure can be obtained when deposition was performed at 680 ℃ using NaF as the activator. The coating was mainly composed of a TiAl3 outer layer, a TiAl2 inner layer, and a thin Al-rich TiAl inter-diffusion layer. The growth of the coating exhibited a positive linear correlation between coating thickness increase and the square root of deposition time. The high-temperature oxidation tests showed that a dense scale mainly composed of Al2O3 and a small amount of TiO2 formed on the coating after oxidation at 950 ℃ for 100 h. The scale possessed excellent high-temperature oxidation resistance, with a parabolic rate constant of the oxidation weight gain approximately 4.9×10-3 mg2/cm4 h, which is lower than that of the TiAl substrate by about three orders of magnitude, and lower than that of the pure Al diffusion coating more than one order of magnitude.

Front-of-pack labelling (FOPL) systems, such as the Nutri-Score, play a crucial role in promoting healthy diets and raising consumer awareness. Our study aimed to gather the opinions of Polish experts on the Nutri-Score and its relation to an ideal information system. We conducted a Poland-wide expert opinion study using a cross-sectional design survey with 75 participants, who had an average of 18±13 years of experience and were mainly employed at medical and agricultural universities. The data were collected with CAWI method. The results showed that the most important features of an FOPL system were clarity, simplicity, consistency with healthy eating recommendations, and the ability to objectively compare products within the same group. While more than half of the respondents believed that the Nutri-Score provides an overall assessment of a product’s nutritional value and facilitates quick purchasing decisions, it falls short in helping consumers compose a balanced diet and cannot be applied to all product groups. The experts also expressed concerns about the system’s ability to account for a product’s degree of processing, full nutritional value and carbon footprint. In conclusion, Poland’s current labelling system needs expansion, but the Nutri-Score requires significant and deep changes and validation against national guidelines and expert expectations before implementation.

After an introductory reminder of safety concerns pertaining to early rechargeable battery technologies, this review discusses current understandings and challenges of sodium-ion batteries. Sodium-ion technology is now being marketed by industrial promoters who are advocating its workable capacity, use of readily accessible and cheaper key cell components. Often claimed to be safer than lithium-ion cells, currently only limited scientific-sound safety assessment of sodium-ion cells has been performed. However, the predicted sodium-ion development roadmap reveals that significant variants of sodium-ion batteries will potentially enter the market in the near future. With recent experiences of lithium-ion battery failures, sodium-ion battery safety management will constitute a key aspect of successful market penetration. As such this review discusses the safety issues of sodium-ion batteries presenting a twofold innovative perspective: i) in terms of comparison with the parent lithium-ion technology making use of the same working principle and similar flammable non-aqueous solvent basis and ii) anticipating the arrival of innovative sub-chemistries at least partially inspired from successive generations of lithium-ion cells. The authors do hope that the analysis provided will assist the concerned stakeholders in the quest for safe marketing of sodium-ion batteries.

The state of charge estimation is an important part of the battery management system, the estimation accuracy of which seriously affects the working performance of the lithium ion battery pack. The unscented Kalman filter algorithm has been developed and applied to the iterative calculation process. When it is used to estimate the SOC value, there is a rounding error in the numerical calculation. When the sigma point is sampled in the next round, an imaginary number appears, resulting in the estimation failure. In order to improve the estimation accuracy, an improved adaptive square root - unscented Kalman filter method is introduced which combines the QR decomposition in the calculation process. Meanwhile, an adaptive noise covariance matching method is implied. Experiments show that the proposed method can guarantee the semi-positive and numerical stability of the state covariance, and the estimation accuracy can reach the third-order precision. The error remains about 1.60% under the condition of drastic voltage and current changes. The conclusion of this experiment can provide a theoretical basis of the state of charge estimation in the battery management of the lithium ion battery pack.

We explore 3D printing modules for self-assembling spacecraft and robots – structure, actuators, electrics. Self-assembly has long been viewed as a highly desirable capability for autonomous construction of large space structures. We review self-assembly in space which focusses on the self-assembly of modules that demonstrate the range of applications. However, self-assembly may be synergised with 3D printing to offer an automated capability from raw material to modules for assembling new spacecraft or habitats. One application of 3D printing is using space debris on-orbit as an in-situ resource - defunct spacecraft may be salvaged as raw material for in-situ construction on demand. The common features of all self-assembling modules are that the modules constitute a structure housing a computer-controlled actuator internally and a reversible latching mechanism externally. We have demonstrated a 3D printed DC electric motor in which the only components that were not 3D printed are the wire coils. We have married our 3D printed motor prototype as an actuated joint between two 3D printed trigon-type panels developed as part of a trigon self-assembling system concept. The trigon concept underlies a modular approach to self-assembling and self-deploying structures. The 3D printed motorised panel system demonstrates that the motor aspect and structural aspects of robotic self-assembling machines are amenable to 3D printing. This has implications for self-assembling systems into modular satellites as a solution to space debris.

Urbanization influences food culture, particularly in low- and middle-income countries, where there is an increasing consumption of processed and pre-packaged foods. This shift is contributing to a rise in non-communicable diseases. Food labeling standards are crucial for regulating manufacturing practices and aiding consumers in making healthy food choices. We aimed to assess the compliance of local and imported pre-packaged snacks with Tanzanian and international labeling standards in Dar es Salaam, Tanzania. A cross-sectional study was conducted on 180 snack products. A checklist based on Tanzanian and Codex labeling standards was used to evaluate adherence. We also examined factors influencing adherence, such as product origin, price, category, purchase location, and package size. The majority of the snacks demonstrated partial adherence to labeling standards. Imported products showed significantly better full adherence to both Tanzanian and International standards. Notably, over half of the products used English for labeling, and infrequently used the recommended World Health Organization Front-of-Pack nutrition Labeling. Product category, origin, and package size were significantly associated with higher levels of International standard adherence (p<0.05). The inadequate adherence to mandatory labeling standards, scarce use of Swahili and FoPL highlight the need to strengthen labeling practices and potential challenges faced by consumers in understanding nutritional information. Thus, strengthening and emphasizing good labeling practices is of urgency as we seek to address diet-related Non-communicable diseases.

Accurate and stable cost forecasting of substation projects is of great significance to ensure the economic construction and sustainable operation of power engineering projects. In this paper, a forecasting model based on the improved least squares support vector machine (ILSSVM) optimized by wolf pack algorithm(WPA) is proposed to improve the accuracy and stability of the cost forecasting of substation projects. Firstly, the optimal features are selected through the data inconsistency rate (DIR), which helps reduce redundant input vectors. Secondly, the wolf pack algorithm is used to optimize the parameters of the improved least square support vector machine. Lastly, the cost forecasting method of WPA-DIR-ILSSVM is established. In this paper, 88 substation projects in different regions from 2015 to 2017 are chosen to conduct the training tests to verify the validity of the model. The results indicate that the new hybrid WPA-DIR-ILSSVM model presents better accuracy, robustness and generality in cost forecasting of substation projects.

The automotive industry is continuously developing to meet the needs of users in terms of efficiency and convenience. The Thailand government has set a policy for Thailand to be a hub for the production of electric vehicles and key components in the region, with a target to produce electric and zero-emission vehicles by 2030. This article is an example of communication in an electric vehicle system. The CAN Bus system is a communication system in electric vehicles that can receive and send communication data via CAN-Hight/Low lines designed for vehicles. CAN Bus is a standard communication system supported by global organizations and used in modern automotive systems. The design of the communication system in electric vehicles uses MRS Developers Studio software to help write programs to receive and send data and prioritize the importance of the received data. The system consists of communication examples studied, such as pressing the start button, turning on/off the headlights, turning on/off the turn signal, turning on/off the brake light, turning on/off the emergency light, sending the horn signal, sending the signal to shift forward/backward, and tuning the motor gear system. From the communication examples mentioned, the communication will be a prototype transport set for small electric vehicles under the scope of the lithium battery energy storage system, NMC type, size 72 V 25 Ah, to test the use, efficiency, and stability in CAN Bus communication up to 1000 times.

Background: Front-of-pack-labels (FOPLs) on packaged foods provide consumers with essential information about the nutritional content of food products, enabling them to make informed choices and align their dietary habits with their health goals. However, evidence on the comprehensibility, use, and effectiveness of FOPLs remains limited, particularly in low- and middle-income countries like Kenya. Objective: In this study, we assessed the effectiveness of three FOPLs in helping consumers identify excess nutrients of concern in packaged food products and their potential influence on food purchases in Kenya. Methods: A total of 2198 shoppers with diverse backgrounds were recruited from selected supermarkets in three Kenyan main cities (Nairobi, Mombasa, Kisumu) and a small town (Garissa). Participants were randomized to three FOPLs: Red and green Octagon label (RG), Red and Green Octagon with icons (RGI) and a black Octagon Warning label (WL). In the control phase, participants were shown unlabeled images of packaged food products and they responded to a set of questions. In the experimental phase, the same product images were presented with one of the three front-of-pack labels they were randomized to, and participants answered the same questions again. Differences in the proportions of participants correctly identifying the nutrients of concern and the changes in intention to purchase unhealthy foods before and after exposure to FOPLs were analyzed using frequency tables and Chi-Square tests. The effectiveness of the three FOPLs was further assessed using a modified Poisson regression. Results: Results showed that exposure to FOPLs significantly improvement participants' ability to correctly identify nutrients of concern across various food categories. Additionally, FOPLs reduced consumers’ intentions to purchase unhealthy foods, with the Warning Labels (WL) emerging as particularly effective in enhancing consumers' understanding of product healthiness and reducing the intention to purchase unhealthy foods compared to the other two FOPLs. Conclusion: These findings underscore the potential role of FOPLs, particularly the WL as an effective regulatory tool for promoting healthier food choices in Kenya.

This literature review investigates the role of plumage in the hunting tactics of Velociraptor, integrating anatomical analysis and biomechanical modeling. Velociraptor, a swift and agile theropod from the Late Cretaceous, exhibited advanced intelligence and sensory capabilities that contributed to its effective predatory strategies. Recent discoveries have confirmed that Velociraptor was covered in feathers, with quill knobs indicating well-developed plumage. This review explores the potential functions of feathers beyond flight, focusing on their impact on hunting behavior. Evidence suggests that Velociraptor’s plumage likely facilitated camouflage and enhanced aerodynamic control, improving its stealth and maneuverability during high-speed chases. Additionally, feathers might have contributed to stability during incline running, further supporting its adaptability in diverse environments. Velociraptor’s hunting strategies, characterized by agility and precision, were complemented by its feathered anatomy, which may have also played a role in pack hunting and social interactions. Overall, the integration of plumage with Velociraptor’s anatomical features and behavioral adaptations underscores its efficiency as a predator, demonstrating how feathers may have been a critical factor in its successful hunting tactics.