In this paper a dynamic relationship between the CO2 emissions in Finland, Norway and Sweden is presented. With the help of a VAR(2) model, and using the Granger terminology, it is shown that the emissions in Finland are affecting those in Norway and Sweden. Other aspects of this dynamic relationship are presented as well.

A cross-flow ultrafiltration harvesting system of a pre-concentrated microalgae culture was tested in an innovative anaerobic-based WRRF. The microalgae culture was cultivated in a membrane photobioreactor fed with the effluent from an anaerobic membrane bioreactor treating sewage. These harvested microalgae biomass was then anaerobically co-digested with primary and secondary sludge from the water line. Depending on the needs of this anaerobic co-digestion, the filtration harvesting process was evaluated intermittently over a period of 212 days for different operating conditions, mainly the total amount of microalgae biomass harvested and the desired final total solids concentration (up to 15.9 g·L1 with an average of 9.7 g·L1). Concentration ratios of 15-27 were obtained with average transmembrane fluxes ranged from 5 to 28 L·m2·h1. Regarding membrane cleaning, both backflushing and chemical cleaning resulted in transmembrane flux recoveries that were, on average, 21% higher than those achieved with backflushing alone. The carbon footprint assessment shows promising results as the GHG emissions associated with the cross-flow ultrafiltration harvesting process could be less than the emissions savings associated with the energy recovered from the biogas production from the anaerobic valorisation of the harvested microalgae.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

The goal of this study was to evaluate the feasibility of methods based on the Worldwide Harmonized Light-Duty Vehicles Test Procedure Brake Cycle to measure brake wear particle emissions for currently used electrified vehicles. Our results indicated that reducing brake friction work reduced brake wear particle emissions. Commercially available, plug-in hybrid electric vehicles reduced emissions by 85% for PM₁₀, 78% for PM_2.5, and 87% for particle numbers (PNs) compared to vehicles with internal combustion engines. Brake friction work showed a linear relationship with PM₁₀ and PM_2.5. Nanoparticle PM emissions tended to increase slightly with regenerative braking, but did not contribute significantly to the overall PM percentage. the emission events of high number concentrations of nuclei mode particles (<20 nm in diameter) in electric vehicle brake assemblies designed for regenerative braking use under high-temperature, high-load braking conditions with full-friction brakes. The nuclei mode particles amplified the PN emissions and led to a high variability. In strict regulatory certification tests, where measurement reproducibility and stability are required, it is appropriate to measure PNs under brake conditions appropriate for the actual use of electric vehicles rather than under full-friction brake conditions or to remove particle measurements smaller than 20 nm.

Cement industry is one of the highest energy consuming industries. The quantity of fuel and energy needed accounts for most of the cost of cement manufacturing. Thermal power plants generate electricity but are harmful and ineffective by nature. As a backup mechanism to account for main grid failures, batteries can be utilized. In this paper the first ever investigation on battery’s depth of discharge (DOD) for four different kinds of battery technologies is carried out in the framework of cement industry. The intended battery technologies are the lead-acid battery (LA), lithium-ion battery (Li-ion), vana-dium redox battery (VR), and nickel–iron battery (Ni-Fe). Four hybrid energy generation models (HEGMs) for five cement plants of Pakistan using the HOMER pro software are proposed. Cement plants includes Askari Cement Plant, Wah (ACPW); Bestway Cement Plant, Kalar Kahar (BCPKK); Bestway Cement Plant, Farooqia (BCPF); Bestway Cement Plant, Hattar (BCPH); and DG Cement Plant, Chakwal (DGCPC). HEGM-1 comprises of a diesel generator (DGen), a photovoltaic system (PV), a converter, and a battery system. HEGM-2 comprises of a PV system, a converter, and a battery system. HEGM-3 is the grid-connected version of HEGM-1 and HEGM-4 is the grid-connected version of HEGM-2. A base-model consisting of grid only is used as a reference. A multi-criteria decision analysis (MCDA) is performed by formulating a cumulative objective function (COF) which includes net present cost (NPC), levelized cost of energy (LCOE), and greenhouse gas (GHG) emissions. The principal objective is the maximization of COF while simultaneously minimizing the objectives (NPC, LCOE and GHG emissions), based on optimal battery technology and DOD. The results reveal that VR is the most suitable battery technology with 10% DOD. It is achieved for DGCPC with HEGM-3 with 61.49% of NPC, 78.62% of LCOE and 84.00% of GHG emissions reduction as com-pared to the base model.

The paper presents data from a monthly campaign for the elemental composition of PM10 in a specific receptor Kotórz Mały (Opole Voivodeship) located in the vicinity of a moderately inhabited rural area, measured in one-hour samples with the use of the PX-375 analyzer by the Horiba company. The hourly variability of SO2, NO, NO2, CO, O3 concentrations as well as the variability of meteorological parameters were also determined. On average, during the entire measurement period, the elements related to PM10 can be arranged in the following order: As<V<Ni<Pb<Cr<Mn<Cu<Ti<Zn<K<Fe<Ca<Al<Si<S. Trace elements, including toxic elements, such as As, V, Ni, Pb, Cr, Mn, were present in low concentrations, not exceeding 10 ng/m3 (average daily value). These elements had fairly even concentrations, daily and hourly. The concentrations of the main elements in the PM10 in the receptor are subject to strong hourly changes related not only to changes in the structure of the sources identified in the statistical analysis but mainly to wind speed and direction changes (soil and sand particles pick-up and inflow of pollutants from coal combustion). It has been shown that the transport emission in the receptor can have an intense effect on PM10 in the afternoon.

Structural self-organizing and pattern formation are universal and key phenomena observed during growth and cluster-assembling of the carbyne-enriched nanostructured metamaterials at the ion-assisted pulse-plasma deposition. Fine tuning these universal phenomena opens access to designing the properties of the growing carbyne-enriched nano-matrix. The structure of bonds in the grown carbyne-enriched nano-matrices can be programmed by the processes of self-organization and auto-synchronization of nanostructures. We propose the innovative concept, connected with application of the universal Cymatics phenomena during the predictive growth of the carbyne-enriched nanostructured metamaterials. We also propose the self-organization approach for increase stability of the long linear carbon chains. The main idea of suggested concept is manipulating by the self-organized wave patterns excitation phenomenon and their distribution by the spatial structure and properties of the nanostructured metamaterial grows region through the new synergistic effect. Mentioned effect will be provided through the vibration-assisted self-organized wave patterns excitation along with simultaneous manipulating by their properties through the electric field. We propose to use acoustic activation of the plasma zone of nano-matrix growing. Interaction between the inhomogeneous electric field distribution generated on the vibrating layer and the plasma ions will serve as the additional energizing factor controlling the local pattern formation and self-organizing of the nano-structures. Suggested concept makes it possible to provide precise predictive designing the spatial structure and properties of the advanced carbyne-enriched nanostructured metamaterials.

Understanding speech in noise is particularly difficult for individuals occupationally exposed to noise due to a to a mix between noise-induced auditory lesions and energetic masking of speech signal. For years, the monitoring of conventional audiometric thresholds has been the usual way to check and preserve the auditory function. But the highlighting of supra-threshold deficits, notably speech in noise understanding difficulties, has pointed out the need for new monitoring tools. The present study aims to identify the most important variables that predict speech in noise under-standing in order to suggest a new way of regular monitoring. Physiological (distortion products of otoacoustic emissions, electrocochleography) and behavioral (amplitude and frequency modula-tion detection thresholds, conventional and extended high frequency audiometric thresholds) variables were collected in a population of individuals presenting a relative homogeneous occu-pational noise exposure. Those variables were used as predictors in a statistical model (random forest) to predict scores of three different speech in noise tests and a self-report of speech in noise ability. The extended high frequency threshold appears to be the best predictor and therefore an interesting candidate for a new way of monitoring noise exposed professionals.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land are a major cause of increasing atmospheric pCO2. Our modelling analysis of reactions by dissolved inorganic carbon shows that increasing atmospheric CO2 could be caused thermodynamically by falling land surface pH values. This hypothesis challenges the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels. Strong acids generated by oxygen from reduced nitrogen and sulphur emits CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils from pH 6.5 to above 8. Each general decrease of aqueous pH value of 0.01 units from acidification of surface water potentially increases the pCO2 in the atmosphere by about 7 ppmv. Contrary to prevailing assumptions that CO2 emissions from combusting fossil fuels can remain in the atmosphere for more than a millennium, such emissions may be partly nullified by global greening from enhanced rates of photosynthesis as well as oceanic absorption. The surface pH value of the ocean has been shown to decrease as atmospheric pCO2 rises. Therefore, our qualitative estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. To the extent that significant acidification of the land is occurring, through export of alkaline produce, the use of artificial nitrogen fertilisation and possible other causes, the prevailing methods of reducing CO2 emissions will fail. However, these acidifying processes on land have not been considered by previous biogeochemical reviews. Despite counter measures, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address such a major cause. This hypothesis can be tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions described in this article with those when corrective counter measures are applied.

A controlled ammonia (NH₃) release experiment was performed at a grassland site to quantify the effect of dry deposition, at the field scale between the source and the receptors (NH₃ measurement locations), on the estimates of emission rates by means of inverse dispersion modelling. NH₃ was released for 3 hours at a constant rate of Q = 6.29 mg s⁻¹ from a grid of 36 orifices spread over an area of 250 m². The increase in line-integrated NH₃ concentration was measured with open-path optical miniDOAS devices at different locations downwind of the artificial source. Using a backward Lagrangian stochastic (bLS) dispersion model (bLSmodelR), the fraction of the modelled release rate to the emitted NH₃ (Q_bLS/Q) was calculated from the measurements of the individual instruments. Q_bLS/Q was found to be systematically lower than 1, on average between 0.69 and 0.91, depending on the location of the receptor. We hypothesized that NH₃ dry deposition to grass and soil surfaces was the main factor responsible for the observed depletion of NH₃ between source and receptor. A dry deposition algorithm based on a deposition velocity approach was included in the bLS modelling. Model deposition velocities were evaluated from a ‘big‑leaf’ canopy resistance analogy. Canopy resistances (generally termed Rc) that provided Q_bLS/Q = 1 ranged from 75 to 290 s m⁻¹, showing that surface removal of NH₃ by dry deposition can plausibly explain the original underestimation of Q_bLS/Q. The inclusion of a dry deposition process in dispersion modelling is crucial for emission estimates, which are based on concentration measurements of depositing tracers downwind of homogeneous area sources or heterogeneously distributed hot spots, such as e.g. urine patches on pastures in the case of NH₃.

The increasing social pressure for decarbonization has placed businesses under considerable scrutiny to actively reduce carbon emissions. A critical step towards achieving this objective is to shift conventional production and consumption systems to more sustainable alternatives. Thus, there is the emergent need to understand the patterns and drivers of the transformative business models (BMs) that underpin that shift. This study adopts a mixed-methods approach that integrates different literature streams--including Sustainability Transitions Theory (STT), Strategic Niche Management (SNM), and the Business Models approach--and stakeholders’ interviews to investigate the key elements of business models that lead towards sustainable practices. This research examines the organizational arrangements of European start-ups operating between 2014 and 2020. The transformation towards decarbonized production and consumption is characterized by efficient combination of business strategies that incorporate advanced technologies (ATs), such as artificial intelligence (AI), machine learning (ML) and its algorithms, along with sustainable elements, resulting in transformative business models. By exploring the driving elements behind the transition to low-carbon approaches, this study fills a significant gap in the existing literature on business models. The findings from this research also hold relevance for policymakers to promote decarbonization.

The building sector has a big potential to reduce the material resource demand needed for building construction and therefore, greenhouse gas (GHG) emissions. Digitalisation can help to make use of this potential and improve sustainability throughout the entire building’s life cycle. One way to address this potential is through the integration of Life-Cycle Assessment (LCA) into the building process by employing Building Information Modelling (BIM). BIM can reduce the effort needed to carry out an LCA and therefore facilitate the integration into the building process. A review of current industry practice and scientific literature shows two main approaches to address BIM-LCA integration. Either the LCA is performed in a simplified way at the beginning of the building process, or it is done at the very end when all the needed information is available, but it is too late for decision-making. One reason for this is the lack of methods, workflows and tools to implement BIM-LCA integration over the entire building process. Therefore, the main objective of this study is to develop an integrated BIM-LCA workflow implemented into a method for the whole building process using an existing structure for cost estimation. A tool is created and used in a case study in Switzerland to test the developed approach. The results of this study show that LCA can be performed continuously in each building phase over the entire building process using existing BIM modelling techniques. The main benefit of this approach is that the re-work caused by the need for re-entering data and the usage of many different software tools that characterise most of the current LCA practices is minimised. Furthermore, decision-making, both at the element and building levels, is supported.

Accurate prediction of mercury content emitted from fossil-fueled power stations is of utmost importance for environmental pollution assessment and hazard mitigation. In this paper, mercury content in the output gas of power stations’ boilers was predicted using an adaptive neuro-fuzzy inference system (ANFIS) method integrated with particle swarm optimization (PSO). The input parameters of the model include coal characteristics and the operational parameters of the boilers. The dataset has been collected from 82 power plants and employed to educate and examine the proposed model. To evaluate the performance of the proposed hybrid model of ANFIS-PSO model, the statistical meter of MARE% was implemented, which resulted in 0.003266 and 0.013272 for training and testing, respectively. Furthermore, relative errors between acquired data and predicted values were between -0.25% and 0.1%, which confirm the accuracy of the model to deal nonlinearity and representing the dependency of flue gas mercury content into the specifications of coal and the boiler type.

The objective of this study was to identify the factors determining a company’s corporate governance related to climate change. We analyzed the effect of various sustainability corporate governance variables on the disclosure level of climate change governance. These variables included facts such as having a dedicated sustainability executive and board committee, the mediating effect of female representation on the board of directors, number of reporting years according to TCFD, membership in a sustainability index, MSCI ESG rating, the existence of a corporate climate transition plan, a mention of the UN Global Compact and GRI, company location, as well as company size and profitability. By adopting a multi-theoretical framework that included stakeholder theory as well the legitimacy and agency theory, the underlying research study used a sample of 100 of the largest global companies by market capitalization and their reporting for the year 2020. Based on 1,400 observations for fiscal year 2020 and using correlation analysis, univariate and linear multiple regressions, we find a positive association between having a climate transition plan in place, being a leader in sustainability according to MSCI ratings, and being a DJSI constituent and the propensity to disclose information on governance for climate change. In addition, we find a company with a dedicated sustainability executive show an increased tendency to be transparent on climate governance issues. Furthermore, having a company location in a developed country is significantly and positively associated with climate change governance. Surprisingly, gender diversity in the corporate board or having a sustainability board committee did not show any significant correlation between a higher climate change governance level. The same was true for companies being active in either the extractive or non-extractive sector. Companies referring to the Global Reporting Initiative (GRI) or UN Global Compact also did not score higher in climate change governance. Neither did corporate profitability or size play a significant role. Our results are robust to variations and provide valuable insights for researchers, academics, executives, practitioners as well as regulators. As more and more companies are shifting towards a climate change reporting framework, it is of paramount importance that we are able to determine the contributing variables that lead to effective climate change corporate governance. Our results are inconsistent with stakeholder theory and are strongly suggesting that a diversified board and the existence of a sustainability committee that meets often/sufficiently may not necessarily lead to a higher level of transparency/quality regarding climate change. While more research is needed, knowing that a dedicated sustainability executive as well as having a climate plan in place can make a difference in climate change reporting, can be very beneficial to many corporate stakeholders. Given the current urgent climate change situation and the crucial role that corporation play in it, dedicated sustainability positions and committees need to be established. The findings could be useful for managers as well as governmental standards setter and regulators who are interested in improving corporate practices dealing with climate change. This study applies STATA software with various regression models to empirically test the relationship between CG and other variables and corporate climate change reporting.