This article presents a study conducted within a wind tunnel to enhance understanding of the excitation mechanism of stay cable vibration under arid conditions. Numerous wind tunnel tests were meticulously analyzed. Initially, the vibration of the stay cable was measured under steady flow conditions at a flow angle of 45 degrees and an inclination of 25 degrees, while varying wind velocities were applied. Additionally, an investigation into the flow field surrounding the stay cable was conducted in both vertical and horizontal directions. By utilizing two hot wire anemometers in the cable wake, an extensive database of flow field measurements was obtained. The experimental results revealed that the vibration characteristics of the stay cable under the arid conditions considered in this study aligned with findings reported in existing literature. Notably, a deeper comprehension of the excitation mechanism of a stay cable in a dry state was attained. This mechanism is closely associated with the inhibition of Karman vortices and the development of low-frequency vortices. At low wind speeds, Karman vortices predominated, resulting in small-amplitude vibrations. However, as the wind speed increased, the influence of Karman vortices diminished progressively, while the low-frequency vortices grew stronger. These low-frequency vortices exhibited high energy and a significant correlation with shedding along the stay cable, thereby inducing cable vibration in a dry environment.

This study investigates the impact of geomagnetic storms that occurred on June 8, 22-23, and 25, 2015, on the ionosphere in the low-latitude and equatorial regions of Brazil. By examining various data sources, such as solar wind parameters from the ACE satellite, GPS vertical total electron content (VTEC), magnetometer data, and the SAMI2 model, we aimed to simulate the effects of storms on the ionosphere in these regions. Two methods were employed to separate DP2 and Disturbance dynamo (Ddyn) from the ionospheric disturbance current (Diono). Our analysis revealed a positive (negative) ionospheric storm in the VTEC during the main phase (recovery) of the June 22-23 and 25 storms. This observation can be attributed to the combined impact of the eastward prompt penetration of the magnetospheric convection electric field (westward disturbance dynamo electric field) and changes in the storm-time thermospheric [O]/[N_2] ratio based on the GUVI satellite imagery. Notably, the westward disturbance dynamo exhibited a significant amplitude on June 23 in Belem. The amplitude of the D_dyn at Belem (dip lat: - 0.47˚) was greater than that at Alta Floresta (dip lat: - 3.75˚) due to intensified cowling conductivity in Belem. Furthermore, we found that the SAMI2 model provided more accurate results when we replaced the default ExB drift with the vertical drift calculated from the ground-based magnetometer, enabling us to simulate the effect of the westward DDEF on VTEC during daytime.

To investigate the optimum layouts of small vertical axis wind turbines, a two-dimensional analysis of dynamic fluid body interaction is performed via computational fluid dynamics for a rotor pair in various configurations. The rotational speed of each turbine rotor (diameter: D = 50 mm) varies based on the equation of motion. First, the dependence of rotor performance on the gap distance (gap) between two rotors is investigated. For parallel layouts, counter-down (CD) layouts with blades moving downwind in the gap region yield a higher mean power than counter-up (CU) layouts with blades moving upwind in the gap region. CD layouts with gap/D = 0.5–1.0 yield a maximum average power that is 23% higher than that of an isolated single rotor. Assuming isotropic bidirectional wind speed, co-rotating (CO) layouts with the same rotational direction are superior to the combination of CD and CU layouts regardless of the gap distance. For tandem layouts, the inverse-rotating configuration (IR) shows an earlier wake recovery than the CO configuration. For 16-wind-direction layouts, both the IR and CO configurations indicate similar power distribution at gap/D = 2.0. For the first time, this study demonstrates the phase synchronization of two rotors via numerical simulation.

A ducted photovoltaic façade (DPV) unit Studied using experimental Prototype and simulated in a full scale Computational Fluid Dynamics CFD Model. The Study comes in two parts; This is Part I with the title detailed above and Part II titled ‘A Ducted Photovoltaic Façade Unit with Buoyancy Cooling: Part II CFD Simulation’.. The process adopted in the experimental study is replicated in the simulation Part. The aim was to optimize the duct width behind the solar cells to allow for maximum buoyancy-driven cooling for the cells during operation. Duct widths from 5 to 50 cm were tested in a Proto-type. A duct width of 45 cm had the maximum calculated heat removed from the duct; however, the lowest cell-operating temperature was reported for duct width of 50 cm. It was found that the DT between ducts' inlets and outlets range from 5.47 °C to 12.32 °C for duct widths of 5–50 cm, respectively. The ducted system enhanced module efficiency by 12.69% by reducing PV temperature by 27 °C from 100°C to 73 °C. The maximum calculated heat recovered from the ducted PV system is 422 W. This is 47.98% from the incident radiation in the test. Total summation of heat recovered and power enhanced by the ducted system is 61.67%.

Almost contact complex Riemannian manifolds, known also as almost contact B-metric manifolds, are equipped with a pair of pseudo-Riemannian metrics that are mutually associated with each other using the tensor structure. Here we consider a special class of these manifolds, those of the Sasaki-like type. They have an interesting geometric interpretation: the complex cone of such a manifold is a holomorphic complex Riemannian manifold (also called a Kähler–Norden manifold). The basic metric on the considered manifold is specialized here as a soliton, i.e. has an additional curvature property such that the metric is a self-similar solution of an intrinsic geometric flow. Almost solitons are more general objects than solitons because they use functions rather than constants as coefficients in the defining condition. A β -Ricci-Bourguignon-like almost soliton ( β is a real constant) is defined using the pair of metrics. The introduced soliton is a generalization of some well-known (almost) solitons (such as those of Ricci, Schouten, Einstein), which in principle arise from a single metric rather than a pair of metrics. The soliton potential is chosen to be pointwise collinear to the Reeb vector field, or the Lie derivative of any B-metric along the potential to be the same metric multiplied by a function. The resulting manifolds equipped with the introduced almost solitons are characterized geometrically. Appropriate examples for two types of almost solitons are constructed and the properties obtained in the theoretical part are confirmed.

Living walls (LWs) are a climate change adaptation strategy for cities, as they have a cooling effect. Previous studies of the cooling effect of LWs were carried out in different climatic zones. These studies differed in their experimental design, or simulated data via models. Plants’ cooling capacity is explained by shading and transpiration, and depends on physical plant parameters, environmental factors, and system-related influences. A three-year-long trial was carried out between 2017 and 2019 at an experimental garden in Geisenheim, Germany. We chose a textile-based LW system with high water demand and plants from a wet/fresh habitat. We assumed that this would achieve high evaporative cooling. The experimental setup included four experimental walls which were exposed to the north, south, east, and west, respectively. The plant choice was divided into three plant mix variants (Cascade, Ground cover, and Meadow) and a Control with no vegetation. We measured the temperature with sensors and a thermal imaging (IR) camera in different setups. The main results were that the measured vegetation temperature (TV) depends on air temperature (TA), measurement position, plant mix variant, and plant species. We could detect the cooling effect only at a small distance from the LW (microclimatic). Our methodological approaches should be continued in further studies.

Object of this work is the design and the simulation of a hybrid UAV with VTOL capabilities that has been designed for landing on naval moving platforms. The work is focused on the innovative propulsion layout adopted on the UAV. Authors discuss how adopted low level control strategies can exploit the innovative features of the proposed system assuring a good rejection of transversal wind disturbances. Particular attention is dedicated to low level modelling and control of the system emphasizing how choices regarding low level actuation and control should improve performances and robustness of the system.

It has been shown that the Micro-Rain Radar (MRR) can be used to derive rainfall rates every 10 m over a depth of 1.28 km using the mean vertical air velocity corrected Doppler raindrop fall speed spectra. Furthermore, it has been shown that by assuming a reasonable advection velocity for the rain, these data can be analyzed to produce spatial radial power spectra often readily fit using a power function. Previous work has shown, however, that each spectrum applies only to each particular set of data and usually lacks the statistical qualifications necessary to be considered generally applicable. However, this limitation does not preclude the potential existence of other generalizations that can be used to explore the rainfall formation processes. The intent of this study, then, is to perform an initial look for such possible behaviors using time-height profiles of the rainfall rate. It is found that once the rainfall rate, R, exceeds about 20 mm h-1, there is, apparently, an associated flattening of the spectra with increasing R so that the smaller scales play an ever increasingly important role in such rain near the ground perhaps reflecting the increasing importance of such scales in the formation of pockets of more intense convective rain. The true generality of this finding needs additional scrutiny using more data particularly from two spatially separated MRR as is currently under preparation.

A realistic approach for gathering high-resolution observation of the rainfall rate, R, in the vertical plane is to use data from vertical pointing Doppler radars. After accounting for the vertical air velocity and attenuation, it is possible to determine the fine, spatially resolved drop size spectra and to calculate R for further statistical analyses. The first such results in a vertical plane are reported here. Specifically, we present results using MRR-Pro Doppler radar observations at resolutions of ten meters in height over the lowest 1.28 km as well as ten seconds in time over four sets of observations using two different radars at different locations. Both correlation functions and power spectra are useful for translating observations and numerical model outputs of R from on one scale down to other scales that may be more appropriate to particular applications such as flood warnings and soil erosion, for example. However, it was found in all cases that while locally applicable radial power spectra could be calculated, because of statistical heterogeneity, most of the power spectra lost all generality and proper correlation functions could not be computed in general except for one 17 minute interval. Nevertheless, these results are still useful since they could be combined to develop catalogs of power spectra over different meteorological conditions and in different climatological settings and locations. Furthermore, even within the limitations of these data, this approach is being used to gain a deeper understanding of rainfall to be reported in a forthcoming paper.

We investigated the radioclinical outcomes of naviculectomy and limited/tailored soft-tissue releases in a short series of ambulatory children with complex/intractable congenital vertical talus subsets namely neglected, multiple operated and recurrent patients. We postulated that this technique will yield satisfactory radioclinical outcomes and minimal complications because it avoids extensive surgical release/trauma that is otherwise classically recommended for complex congenital vertical talus (CVT). The cohort consisted of five -four boys, one girl- complex CVT children with neglected, multiple operated and/or recurrent subsets. Patients were included if manipulative casting techniques were deemed unlikely to produce a plantigrade foot. Patients underwent naviculectomy with variable on-demand limited soft tissue releases. Two patients had bilateral affection and two had a non-idiopathic aetiology. The mean age was 5.2 years (4 to 6.25) and mean follow-up was 2.3 years (1 to 3). We reported satisfactory outcomes as per foot posture, function, overall parent satisfaction including pain and radiography per lateral views of talar-axis-first metatarsal base angle on the short/intermediate term. Whereas manipulative casting is unlikely to yield lasting outcomes in ambulatory children with complex subsets of CVT, extensive surgical soft-tissue releases have unfavourable long-term complications. As a substitute, naviculectomy as a form of resection arthroplasty created a practical and affordable third way between manipulative casting with minimally invasive surgery and the extensive surgical soft tissue releases on the short/intermediate term.

In this paper, the linear nonequilibrium thermodynamic approach is used to analyze energy processes in the wind energy conversion system (WECS), with a directly connected vertical axis wind turbine (VAWT) and vector controlled permanent magnet synchronous generator (PMSG). Both elements are considered as linear universal energy converters (EC) linearized at the points of the given range of common to VAWT and PMSG angular velocity. The dependences on the angular velocity of the coupling coefficients between the ECs input and output and the dimensionless parameters of their operating modes were received. This allows for choosing the optimal points of ECs operation according to the specified criteria and obtaining indicators of their maximum efficiency. To assess the quality of the cascade connection of two ECs, the appropriate coefficient was introduced, the dimensionless parameters and characteristics of the equivalent EC were obtained, and the conditions of its maximum efficiency were determined. Analysis of the VAWT-PMSG connection quality showed reserves for improving WECS efficiency. The impact of VAWT and PMSG variable parameters on the quality of this connection is studied, and further research directions are shown. The proposed thermodynamic approach allows an effective search for solutions for the efficiency improvement of various systems with energy transfer and transformation.

Ho Chi Minh City (HCMC), the most crowded city and economic hub of Viet Nam, has been experiencing land subsidence over the past decades. This effort aims to contribute the spatial distribution of subsidence in HCMC in its horizontal and vertical components using synthetic aperture radar interferometry (InSAR) time series. To this purpose, an advanced Persistent Scatterers and Distributed Scatterers (PSDS) InSAR technique was applied to two European Space Agency (ESA) Sentinel-1 datasets consisting of 96 ascending and 202 descending images, acquired from 2014 to 2020 over the HCMC area. A time series of 33 COSMO-SkyMed ascending images was also used for comparison. The combination of ascending and descending satellite passes is used to decompose the light of sight velocities into horizontal east-west and vertical components. Taking into account the presence of east-west horizontal motion, our findings indicate that the accuracy of the decomposed vertical velocity can be improved by up to 3 mm/year for Sentinel-1 data. The obtained results revealed that subsidence is most pronounced in the areas along the Sai Gon River, in the northwest-southeast axis, and in the southwest of the city, with a maximum value of 80 mm/yr, which is in accordance with the findings of the literature. The amplitude of east-west horizontal velocities is relatively small and large-scale eastward movement can be observed in the west of the city at a rate of 3-5 mm/yr. This confirmed that the displacement in Ho Chi Minh City area is mainly vertical downward. Together, these results reinforced the remarkable suitability of ESA's SAR Sentinel-1 for subsidence applications, even for non-European countries such as Vietnam and Southeast Asia.

To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

Material identification based on R_value (transparency natural logarithm ratio of low-energy to high-energy) of line-scan dual-energy X-ray transmission (DE-XRT) has a good prospect for industrial application. Unfortunately, the DE-XRT signals before attenuation cannot be directly measured, whereas their precision is very important to R_value. Therefore, a context-based signal synthesis method which takes the filtered signals that remove high-frequency noises and retain low-frequency actual fluctuations as the reference value, and takes into account the vertical (forward/column) direction and horizontal (scanning/row) direction anisotropy of line-scan images was proposed. The vertical is a time series with continuity of signal trend; the horizontal is a spatial characteristic with the fluctuation synchronization within the same row signals. The special synthesis evaluations of curve synthesis difference and surface synthesis difference were also proposed. Experimental results show that the tow evaluations are both only about 0.0007, and it only takes 35 ms to complete the surface synthesis of 119×119 pixels on the CPU with 3.4 GHz main frequency. The presented method can achieve high signal synthesis precision and calculation real-time, so as to facilitate DE-XRT material identification. It can be extended to improve the precision of numerical synthesis in other line-scan uncomplete signals.

We propose an advanced filtering scheme based on Recurrent Neural Networks (RNNs) and Deep Learning to enable efficient control strategies for Vertical Farming (VF) applications.  We demonstrate that the best RNN model incorporates five neuron layers, with the first and second containing ninety Long Short-Term Memory neurons.  The third layer implements one Gated Recurrent Units neuron.  The fourth segment incorporates one RNN network, while the output layer is designed by using a single neuron exhibiting a rectified linear activation function.  By utilizing this RNN digital filter, we introduce two variations: (1) A scaled RNN model to tune the filter to the signal of interest, and (2) A moving average filter to eliminate harmonic oscillations of the output waveforms. The RNN models are contrasted with conventional digital Butterworth, Chebyshev I, Chebyshev II, and Elliptic Infinite Impulse Response (IIR) configurations.  The RNN digital filtering schemes avoid introducing unwanted oscillations, which makes them more suitable for VF than their IIR counterparts.  Finally, by utilizing the advanced features of scaling of the RNN model, we demonstrate that the RNN digital filter can be pH selective, as opposed to conventional IIR filters.

Forest canopy gaps are important for the ecosystem dynamics. Depending on tree species, small canopy openings might be also associated to intra-crown porosity and to space between crowns. Yet, little is known on the relationships between the fine-scaled pattern of canopy openings and biodiversity features. This research explored the possibility of i)- mapping forest canopy gaps from a very high resolution orthomosaic (10 cm), processed from a versatile imaging platform such as unmanned aerial vehicles (UAV), ii)- to derive patch metrics that can be tested as covariates of variables of interest for forest biodiversity monitoring. This is attempted in a test area of 240 ha covered by temperate deciduous forest types in Central Italy and containing 50 forest inventory plots of about 530 m². Correlation and linear regression techniques were used to explore relationships between patch metrics and understorey (density, development and species diversity) or forest habitat biodiversity variables (density of micro-habitat bearing trees, vertical species profile, tree species diversity). The results revealed that small openings in the canopy cover (75% smaller than 7 m²) can be faithfully extracted from UAV RGB imagery, using the red band and contrast split segmentation. Highest correlations were observed in the mixed forest (beech and turkey oak), while beech forest had the poorest ones and turkey oak forest displayed intermediate results. Moderate to strong linear relationships were found between gap metrics and understorey variables in mixed forest type, with adjusted R² from linear regression ranging from 0.52 to 0.87. Equally good results, in the same forest types, were observed for forest habitat biodiversity variables (0.52<adjusted R²<0.79) with highest values found for density of trees with microhabitats and vertical species profile. In conclusion, this research highlights that UAV remote sensing can potentially provide covariate surfaces of variables of interest for forest biodiversity monitoring, conventionally collected in forest inventory plots. By integrating the two sources of data, these variables can be mapped over small forest areas with satisfactory levels of accuracy, at a much higher spatial resolution than would be possible by field-based forest inventory solely.

Incremental control strategies provide undeniable advantages for controlling Uncrewed Aerial Vehicles (UAVs) due to their reduced model dependency and accurate tracking capacities. This is of particular relevance for hybrid UAVs, specially for tail-sitters, which perform complex manoeuvres when transitioning to and from aerodynamic flight. This paper summarizes the research undertaken in the application of the Incremental Nonlinear Dynamics Inversion (INDI) and Incremental Backstepping (IBKS) to a small tail-sitter UAV. After the application of these control strategies in a simulated scenario, the implementation in a Micro-Controller Unit was validated in a Hardware-in-the-Loop scenario. Following such validation, indoor experimental trials were undertaken in order to evaluate the capacity of these controllers to stabilize and control the real aircraft. The stabilization in the flight trials was successfully implemented and allow to conclude that both INDI and IBKS are control strategies suited to control a tail-sitter in vertical flight, providing accurate tracking capabilities under smooth actuation. Furthermore, it was found that the IBKS is significantly more computationally demanding than the INDI, although having a global proof of stability that is of interest in aircraft control.

The burgeoning field of Urban Air Mobility (UAM) promises transformative solutions to urban transportation challenges, with the potential to revolutionize cargo logistics in metropolitan areas. This research investigates the role of tiltrotor technology as a pivotal enabler of seamless UAM integration for efficient cargo transportation within urban environments. The study delves into the existing challenges within UAM, such as infrastructure limitations and the need for adaptable aerial vehicles that can navigate confined spaces while maintaining payload capacity. Tiltrotor Unmanned Aerial Vehicles (UAVs) are examined as a solution to these challenges due to their unique capabilities, combining vertical takeoff and landing (VTOL) with efficient forward flight. This research evaluates the potential of tiltrotor UAVs for urban cargo transportation, focusing on their operational efficiency, safety, and economic viability. Furthermore, the study explores the potential impact of tiltrotor technology on urban cargo logistics, considering factors such as reduced congestion, shorter delivery times, and environmentally sustainable operations. Real-world case studies and practical implementation strategies are discussed, shedding light on the importance of integration of tiltrotor UAVs into existing cargo transportation networks.The findings of this research underscore the transformative potential of tiltrotor technology in enhancing UAM for cargo transportation within urban areas. The study contributes valuable insights to the ongoing discourse on UAM integration and lays the groundwork for future developments in autonomous aerial cargo delivery systems.

Clustering is a data mining task used for the data extraction from the data bases or files. Clustering is used to find unknown groups present in the data sources like files or data bases. This paper focuses on clustering algorithms performance dependency on the parallel clustering platforms and the clustering algorithms along with their clustering criteria. The problems with the present Traditional clustering algorithms were throughput and data source size changes (scalability). So they can’t address the big data. So for handling the huge volumes of data, parallel clustering algorithms along with clustering criteria were used. For processing the big Data Parallel clustering algorithms are of two types based on computing platforms used. They were the horizontal scaling platforms and vertical scaling platforms.

Monitoring crown closure evolution using multi-temporal Light Detection and Ranging (LiDAR) surveys is a method that we expect to be increasingly adopted given the availability of LiDAR sensors and the accumulating survey archives. However, little attention was devoted to comparing crown closure estimates from independent surveys. Although survey parameters cannot be modified after the data collection, we speculate that the error associated to crown closure estimates comparison can be reduced by selecting optimal post-survey parameters. In this study, we compared crown closure estimates of three airborne LiDAR surveys from 2018 (40 pt/m²) used as a reference, and two lower-density surveys from 2016 (4.5 pt/m²) and 2018 (2 pt/m²). We studied the effect of the height threshold used to separate canopy points and the grid resolution, using skewness and variance of lagged difference of crown closure. Crown closure estimates using low height thresholds were more different across surveys, resulting in higher root mean squared error (RMSE), bias and more different variograms. Results show that optimal height threshold was 3 m and grid resolution was 25 m, although there was room for decision (RMSE of 7% and 5%, and bias of 4% and 0% for 2016 and 2018 low-density surveys).

Sea level rise due to global warming is a continuing and, disappointingly, accelerating process, which has already affected and will further impact coastal lowlands and the social and economic activities in these areas. Delos Island, situated in the middle of the Cyclades in the Aegean Sea, was considered the most sacred of all islands in ancient Greek culture and a trading hub for the entire eastern Mediterranean. Uninhabited since the 7th century AD, and consistently the focus of research and touristic attention, the island is designated as an archaeological site and inscribed on the Unesco World Heritage List. Previous studies on the relative sea level (rsl) changes suggest a steadily rsl rise during the last 6,300 years, starting from a sea level at -4.80±0.20m in the Late Neolithic. The seafront of the ancient city of Delos is subject to the effects of the rsl rise, which have caused significant coastline retreat and exposure to the northerly winds and waves, whereas parts of the coastal lowland where the remains of the ancient city lie are inundated, forming extended wetlands. The future impacts of rsl rise on the seafront of ancient Delos are illustrated on very high-resolution digital surface models, evaluating both the flooding risk under different climatic projections, as provided by the IPCC AR6 report, and the ongoing land subsidence, as recorded by GNSS data. An rsl rise ranging from 87cm (SSP1-2.6 scenario) to 148cm (SSP5-8.5 scenario) is anticipated by 2150, requiring both resilience strategies and adaptation solutions as well as mitigation policies to cope with the effects of climate change.

This study addresses the enhancement of material efficiency and reduction of brittleness in timber-to-concrete adhesive connections for beam-type timber and timber-concrete composite panels. The research explores the potential benefits of adding longitudinal timber ribs to Cross-Laminated Timber (CLT) beam-type panels. Three groups of flexure-tested specimens were analysed: (1) timber panels (1400 mm × 400 mm) with two 100 mm thick CLT panels and two 60 mm thick CLT panels reinforced with 150x80 mm timber ribs; (2) eight specimens (600 mm × 100 mm × 150 mm) with CLT members (600 mm × 100 mm × 100 mm) connected to a 50 mm concrete layer using granite chips and Sikadur-31 (AB) epoxy adhesive; (3) six CLT panels (1400 mm × 400 mm × 50 mm) bonded to a 50 mm concrete layer, with two panels containing polypropylene microfibers and two panels incorporating polyethene dowels for mechanical connection. Specimens were subjected to three-point bending tests and analysed using the transformed section method, γ-method, and finite element method with ANSYS 2023R2 software. Results indicated a 53% increase in load-carrying capacity for ribbed CLT panels with no additional material consumption, a 24.8%-41.1% increase for CLT panels strengthened with a concrete layer, and improved ductility and prevention of disintegration in timber-concrete composites with polypropylene microfibers.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.