We present synthetic experiments of lactic acid (LA) polycondensation to produce poly(lactic acid) (PLA), as well as kinetic modeling calculations that capture the polymer molecular weight increase with time, given the initial concentrations. Tin-octoate-catalyzed polycondensation of (D,L)- or L-lactic acid, was carried out in pre-dried toluene after azeotropic dehydration for 48-120 hours at 130-137 °C. The polymerization was optimized by varying lactic acid and catalyst concentrations as well as the temperature. Gel Permeation Chromatography was used to experimentally follow the evolution of molecular weights and the products were characterized by NMR, TGA, DSC and IR. Under optimal conditions, PLLA with weight-average molecular weight (Mw) of 161 kDa could be obtained. The rate equations that describe polycondensation kinetics were recast in a condensed form that allowed very fast numerical solution and calculation of the number-average molecular weight with time. Deviations with respect to the experiment were minimized in a least-squares fashion, to determine rate constants. The optimized kinetics parameters are shown to reproduce the experimental data accurately

Vertical and horizontal bone augmentation is one of the most challenging techniques in bone engineering. The use of barrier membranes and scaffolds in guided bone regeneration (GBR) procedures is a common approach for the treatment of lost bone around teeth and dental implants. The aim of this study was to estimate the barrier effects of a synthetic poly (lactic acid/caprolactone) [P(PA/CL)] bilayer membrane for GBR, compared to a porcine collagen bilayer membrane, in the vertical augmentation model on 10–12-months old rat skull without periosteum. The HAp block (diameter: 4 mm, height: 3 mm, porosity:75%, average pore size:150 μm) was placed on the rat skull without a periosteum. The P(LA/CL) membrane (solid layer: 25 μm, porous layer: 175 μm) or the collagen membrane (solid layer, porous layer) was applied onto the HAp block. At 3, 6, and 12 weeks after the surgery, the incised tissues were fixed, decalcified, and stained with hematoxylin and eosin for histological evaluation. The P(LA/CL) membrane remained until 12 weeks and could achieve barrier effects to inhibit cellular invasion from the repositioned soft tissues. Local bone formation occurred in the interconnected pores of HAp at 6 weeks. On the other hand, the collagen membrane did not inhibit cellular invasion for its expansion until 3 weeks, and was absorbed until 6 weeks. The results indicated that the P(LA/CL) membrane might be effective in GBR as occlusive absorbable membrane.

Poly (Lactic Acid) (PLA) / Ground Tire Rubber (GTR) blends using Dicumyl peroxide (DCP) as a crosslinking agent were prepared as a route to recycle wastes rubber from the automotive industry. The GTR were exposed to grinding and exhibited mechanical damage, traduced at the rubber network scale by chains scission and/or chemical cross-links breakage. Such damage is accompanied by a decrease of 80% of the rubber chains network density of the initial tire buffing but found independent on the type of grinding (cryogenic, dry ambient) or on the GTR size (from <400 µm to <63 µm). Moreover, the finest sieved GTR contain the largest the amount of reinforcing elements (carbon black, clay) that can be advantageously used in PLA/GTR blends. The melt-blending of these finest GTR particles obtained by cryo-grinding at an amount of 15 wt.% and in presence of the crosslinking agent (DCP), resulted in an optimum improvement of the ductility, energy at break and impact strength of the PLA/GTR blends as compared to neat PLA, while maintaining its stiffness. The results were attributed to (i) the good dispersion of the fine GTR particles into the PLA matrix, (ii) the partial re-crosslinking of the GTR particles and co-crosslinking at PLA/GTR interface and (iii) the presence of reinforcing carbon black into the GTR particles and clay particles dispersed into the PLA matrix.

Electrospinning is the versatile technique to generate large quantities of micro- or nano-fibers from a wide variety of shapes and sizes of polymer. Natural bone is a hierarchically composites with the dispersion of inorganic ceramic along organic polymer. The aim of this study, the electrospun poly (lactic acid) (PLA) mats coated with chitosan (CH) and calcium silicate (CS) powder were fabricated. The morphology, chemical composition, and surface properties of CS/CH-PLA composites were characterized by scanning electron microscopy, X-ray diffraction, and Fourier transform infrared spectroscopy. In vitro, the CS/CH-coated PLA mats increased the formation of apatite on the surface when soaking in cell cultured medium. During culture, the adhesion and proliferation of the human mesenchymal stem cells (hMSCs) cultured on CS/CH-PLA were significantly promoted relative to those on PLA. Collagen I and fibronectin levels and promoted cell adhesion were observed upon an increase in CS content. Further, compared to PLA mats without CS/CH, CS10 and CS15 mats markedly enhanced the proliferation of hMSCs as well as their osteogenesis properties, which was characterized by bone-related gene expression. Our results demonstrated that the biodegradable and electroactive CS/CH-PLA mats had potential application as an ideal candidate for bone tissue engineering. Together, findings from this study clearly demonstrated that PLLA-C2S composite scaffold may function as an ideal candidate for bone tissue engineering.

This study aims to demonstrate the possibility of incorporating a natural antioxidant biomolecule, into polymeric porous scaffolds. To this end, Poly-L-Lactic Acid (PLLA) scaffolds were produced using the Thermally Induced Phase Separation (TIPS) technique and additivated with different amounts of Rosmarinic Acid (RA). The scaffolds, with a diameter of 4 mm and a thickness of 2 mm, were characterized with a multi-analytical approach. Specifically, Scanning Electron Mi-croscopy analyses demonstrated the presence of an interconnected porous network, character-ized by a layer of RA at the level of the pore’s surfaces. Moreover, the presence of RA biomole-cules increased the hydrophilic nature of the sample, as evidenced by the decrease in contact angle with water from 128° to 76°. This approach is cost-effective, and it could be customized with different biomolecules, offering the possibility of producing porous polymeric structures con-taining antioxidant molecules. These scaffolds meet the requirements of tissue engineering and could be offered a potential solution to reduce inflammation associated with scaffold implantation thus improving tissue regeneration.

Poly lactic acid (PLA) has made inroads for commercial market segment with lot many unique characteristics such as tenacity, low flame rate, moisture regain percentage, loss of ignition percentage, heat of combustion, UV resistance, Elastic recovery and higher melting point allowed it to be the fastest moving material in today's commercial market. An attempt has been made to test the feasibility and biocompatibility aspect of PLA with cement mix. The basic strength and physical test results were carried out and published in an article, to the continuation of the work, micro-structural study was conducted to evaluate the elemental characteristics. Thermo gravimetric analysis revealed that PLA either in granular form or filament will hold good for the inclusion into construction applications, provided degradation aspects are to be looked out for improvisation. From DSC it was found that PLA in filament form is the best inclusion material for construction application, however the tenacity of fibers has to checked, as currently available filaments in market does not have high tenacity value. From EDX reports, 30% inclusion of PLA as replacement for fine aggregate has constituent members as Calcium carbonate(CaCO3), Silica(SiO2) and Wollastonite (CaK) resulted in best composition among the rest. FESEM images revealed that, proper gradation in size, rough surface of PLA granular form or filament form will definitely enhance the mechanical/physical or even chemical behavior of PLA.

The poly lactic acid (PLA) is one of the most used bio-derived thermoplastic polymers in 3D and 4D printing applications. The determination of PLA surface properties is of capital importance in 3D/4D printing technology. (1) Background: The surface thermodynamic properties of PLA polymer were determined by using the inverse gas chromatography (IGC) technique at infinite dilution. The determination of the retention volume of polar and non-polar molecules adsorbed on the PLA particles filling the column allowed us to obtain the dispersive, polar, and Lewis’s acid-base surface properties at different temperatures from 40 °C to 100 °C. (2) Methods: the applied surface method was based on our recent model that used the London dispersion equation and the new chromatographic parameter function of the deformation polarizability and the harmonic mean of the ionization energies of the PLA polymer and organic molecules. (3) Results: The application of this new method led to the determination of the dispersive and polar free surface energy of adsorption of molecules on the polymeric material, as well as the glass transition and the Lewis acid-base constants. (4) Conclusions: four interval temperatures were distinguished showing four zones of the variations of the surface properties of PLA as a function of the temperature before and after the glass transition.

Nanoparticles of graphene and carbon nanotubes are attractive materials for improvement of mechanical and barrier properties and functionality of biodegradable polymers for food packaging applications. However, the increase of the manufacture and consumption increases the probability of exposure of human and environment to such nanomaterials, this rising questions about the risks of nanomaterials since they can be toxic. For a risk assessment, it is crucial to know whether airborne nanoparticles of graphene and carbon nanotubes can be released from nanocomposites into the environment at their end-life, or they remain embedded in the matrix. In this work the release of graphene and carbon nanotubes from the poly(lactic) acid nanocomposite films were studied for the scenarios of: (i) biodegradation of matrix polymer at the disposal of wastes; and (ii) combustion and fire of nanocomposite wastes. Thermogravimetric analysis in air atmosphere, TEM, AFM and SEM were used to verify the release of nanoparticles from nanocomposite films. The three factors model was applied for the quantitative and qualitative risk assessment to the release of graphene and carbon nanotubes from nanocomposite wastes for these scenarios. Safety concern is discussed in respect to the existing regulations for nanowastes stream.

The subject of the conducted study was focused on the development of new type of technical blends reinforced with natural fillers. The study was divided into two parts, where in the firsts stage of the research unmodified POM was reinforced with different types of natural fillers: cellulose, wood flour and husk particles. In order to select the type of filler intended for further modification, the mechanical characteristics was assessed. The 20% wood flour (WF) filler system was selected as the reinforcement. The second stage of research involved the use of combination of polyoxymethylene POM and poly(lactic acid) PLA. POM/PLA blend (ratio 50/50 %) were modified with elastomeric compound (EBA) and chain extender as reactive compatibilized (CE). The microscopic analysis revealed that for POM/PLA system the filler-matrix interface is characterized by better wettability, which might suggest higher adhesion. The mechanical performance revealed that for POM/PLA-based composites the properties were very close to the results for POM-WF composites; however, there is still large difference in thermal resistance in favor of POM-based materials. The increase in thermomechanical properties for POM/PLA composites occurs after heat treatment. The increasing crystallinity of the PLA phase allows for an significant increase of the head deflection temperature (HDT), even above 125 °C.

We used atomistic molecular dynamics (MD) simulations to study polyelectrolyte brushes based on anionic α-L-glutamic acid and α-L-aspartic acid grafted on cellulose in the presence of divalent CaCl2 salt at different concentrations. The motivation is the search of the ways to control properties such as sorption capacity and the structural response of the brush to multivalent salts. For this detailed understanding of the role of side chain length, chemical structure and their interplay is required. It was found that in the case of glutamic acid oligomers, the longer side chains facilitate attractive interactions with the cellulose surface, which forces the grafted chains to lie down on the surface. The additional methylene group in the side chain enables side chain rotation enhancing this effect. On the other hand, the shorter and more restricted side chains of aspartic acid oligomers prevent attractive interactions to a large degree and push the grafted chains away from the surface. The difference in side chain length also leads to differences in other properties of the brush in divalent salt solutions. At a low grafting density, the longer side chains of glutamic acid allow the adsorbed cations to be spatially distributed inside the brush resulting in a charge inversion. With an increase in grafting density, the difference in the total charge of the aspartic and glutamine brushes disappears, but new structural features appear. The longer sides allow for ion bridging between the grafted chains and the cellulose surface without a significant change in main chain conformation. This leads to the brush structure being less sensitive to changes in salt concentration.

One-step reactive melt processing (REx) via radical reaction was evaluated with the aim of improving the rheological properties of poly(ε-caprolactone) (PCL). In particular, a water-assisted REx was designed under the hypothesis of increasing crosslinking efficiency with water as a low viscous medium in comparison with a slower PCL macroradicals diffusion in the melt state. To assess the effect of dry vs. water-assisted REx on PCL, its structural, thermo-mechanical and rheological properties were investigated. Water-assisted REx resulted in increased PCL gel fraction compared to dry REx (from 1 to 34 %), proving the rationale under the formulated hypothesis. From dynamic mechanical analysis and tensile tests, the crosslink did not significantly affect the PCL mechanical performance. Dynamic rheological measurements showed that higher PCL viscosity was reached with increasing branching/crosslinking and the typical PCL Newtonian behavior was shifting towards a progressively more pronounced shear thinning. A complete transition from viscous- to solid-like PCL melt behavior was recorded, demonstrating that higher melt elasticity can be obtained as a function of gel content by controlled REx. Improvement in rheological properties offers the possibility of broadening PCL melt processability without hindering its recycling by melt processing.

New advances of nano-enabled weed management: using poly(epsilon-caprolactone)-based nanoherbicides. A review

Optical rotatory dispersion (ORD) is a beautiful analytical technique for the study of chiral molecules and polymers. In this study, ORD was applied successfully to follow the degree of polycondensation of l-(+)-lactic acid toward the formation of poly(lactic acid) oligomers (PLAO) and high molecular weight poly(l-lactic acid) (PLLA) in a simple esterification reaction equipment. PLLA is a biodegradable polymer obtainable from renewable raw materials. The racemization of the intrinsically isotactic PLLA through thermal treatment can be easily followed through the use of ORD spectroscopy. Organic or molecular electronics is a hot topic dealing with the combination of π-conjugated organic compounds and polymers with specific properties (e.g. chirality) which can be exploited to construct optoelectronic devices such as organic light-emitting diodes (OLEDs), organic photovoltaic (OPV) high efficiency cells, switchable chirality devices, organic field-effect transistors (OFETs), and so on. ORD spectroscopy was applied to study either the gigantic optical rotation of PLLA films as well as to detect successfully the excitonic coupling occurring in thin solid PLLA green film loaded with a combination of two dyes: SY96 (a pyrazolone dye) and PB16 (the metal-free phthalocyanine pigment). The latter compound PLLA loaded with SY96 and PB16 shows a really gigantic optical activity in addition to typical ORD signal due to exciton coupling and may be considered as a simple and easily accessible model composite of a chiral polymer matrix combined with π-conjugated dyes for molecular electronics studies.

Lactic acid production from lactose by Lactiplantibacillus plantarum AC 11S was studied. The influence of initial substrate concentration was investigated, and optimal pH and temperature were determined. An unstructured mathematical model was developed comprising equations for bacterial growth, substrate consumption, and product formation. The model was solved with different terms for specific growth rates considering substrate and/or product inhibition. The best bacterial growth and lactic acid production were achieved at pH = 6.5 and 30 oC. Production of lactic acid was mainly growth-associated and at substrate concentration over 15 g/L a considerable product inhibition was observed. The parameters of different models were determined and compared. While the modified Gompertz equation gave the best fit for biomass growth, a variant of the logistic equation including a term for product inhibition described in the best way the entire set of equations comprising bacterial growth, substrate consumption, and product formation at different initial substrate concentrations.

In this paper, carbon nanotubes modified screen-printed electrode (CNTs/SPE) was prepared and the CNTs/SPE was employed for the electrochemical determination of antioxidant substance Chlorogenic acids (CGAs). A pair of well-defined redox peak of CGA was observed at the CNTs/SPE in 0.10 mol∙L^-1 acetic acid-sodium acetate buffer (pH 6.2) and electrode process is adsorption-controlled. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) method for the determination of CGA were proposed based on the CNTs/SPE. Under the optimal conditions, the proposed method exhibited linear ranges from 4.73×10^-7 to 4.45×10^-5 mol∙L^-1, the linear regression equation was Ipa(µA) = 4.1993 C (mol∙L^-1)+1.1039 (r = 0.9976) and the detection limit for CGA could reach 3.25×10^-6 mol∙L^-1. The recovery of matrine was 94.74~106.65% (RSD = 2.92%) in coffe beans. The proposed method is quick, sensitive, reliable, and can be used for the determination of CGA.

Glutamate decarboxylase (L-glutamate-1-carboxylase, GAD; EC 4.1.1.15) is a pyridoxal 5-phosphate-dependent enzyme, which catalyzes the irreversible α-decarboxylation of L-glutamic acid to γ-aminobutyric acid (GABA) and CO2. The enzyme is widely distributed in eukaryotes as well as prokaryotes, where it – together with its reaction product GABA - fulfils very different physiological functions. The occurrence of gad genes encoding GAD has been shown for many microorganisms, and GABA-producing lactic acid bacteria (LAB) have been a focus of research during recent years. A wide range of traditional foods produced by fermentation based on LAB offer the potential of providing new functional food products enriched with GABA that may offer certain health-benefits. Different GAD enzymes and genes from several strains of LAB have been isolated and characterized recently. GABA-producing LAB, biochemical properties of their GAD enzymes, and possible applications are reviewed here.

Fermented milk product "Laban" in Libya is one of the most a traditional fermented milk product consumed a refreshing drink, particularly in the warm season The average values of the physicochemical including titratable acidity, pH, total solids, and fat were 0.73%, 4.16, 8.12%, and 1.54% respectively. Coliform, yeast and mold counts were 21×10⁴, 39×10⁴, and 41 ×10³ cfu/ ml., respectively. Most strains of coliform bacteria were Serratia odorifera, Escherichia coli 1, E. coli 2. and Klebsiella oxytoca. The average Lactococcus, Streptococcus, Mesophilic Lactobacillus / Leuconostoc and Thermophilic Lactobacillus counts were 99 ×10⁷, 96 ×10⁷, 93 ×10⁷ and 15 ×10⁷ cfu / ml. respectively. A total of 142 lactic acid bacteria (LAB) isolates were identified to the genus level as Lactobacillus (48.59%), Lactococcus (43.66%), Streptococcus (4.93%) and Leuconostoc (2.82%). Sugar fermentation tests revealed the most frequent Lactobacillus species found to be Lactobacillus delbrueckii ssp. lactis (62.32%), followed by Lactobacillus plantarum (31.88%). Furthermore, other selected LAB isolates were identified by API 50 CH test as Lactococcus lactis ssp. lactics, Lactobacillus pentosus, Lactobacillus brevis, and Leuconostoc mesenteroides ssp. cremoris. Thus, our research documented the lactic acid bacteria strains and will provides fundamental basic and useful information for further studies of strain selection starter culture, with regard to the industrial production of fermented dairy milk products.

Electrospun ultrathin fibers based on binary compositions of polylactide (PLA) and poly(ε-caprolactone) (PCL) with different ratios of polymer components from 0/100 to 100/0 wt. % were studied. Using a combination of thermal (DSC) and relaxation (EPR) measurements, the effect of biopolymers content on the characteristics of the crystal structure of PLA and PCL and the diffusive rotational mobility of the stable TEMPO radical in the amorphous regions of PLA/PCL compositions was shown. It was revealed that after PLA and PCL blending, significant changes in the degree of crystallinity of PLA, PCL segmental mobility, sorption capacity of the radical as well as activation energy of rotational diffusion in the amorphous regions of PLA/PCL composition are observed. The characteristic region of biopolymers’ composition from 50/50 to 30/70 % PLA/PCL blends ratio was found, where the inversion transition of PLA from dispersive medium to dispersive phase where an inversion transition is assumed when the continuous medium of the PLA transforms into a discrete phase. The performed studies made it possible for the first time to carry out a comprehensive analysis of the effect of the system component ratio on the structural and dynamic characteristics of the PLA/PCL film material at the molecular level.

Lactic acid bacteria are traditionally applied in a variety of fermented food products and have the capability to produce a wide range of bioactive ingredients during fermentation including vitamins, bacteriocins, bioactive peptides and bioactive compounds. The bioactivity and health benefits associated with these ingredients have gained interest in applications in the functional dairy market and have relevance both as components produced in situ and as functional additives. This review provides a brief description of the regulations regarding the functional food market in the European Union as well as an overview of some of the functional dairy products currently available in the Irish and European markets. A better understanding of the production of these ingredients excreted by lactic acid bacteria can further drive the development and innovation of the continuously growing functional food market.

This work aimed at producing lactic acid (LA) from sugarcane bagasse after steam explosion at 195 ºC for 7.5 and 15 min. Enzymatic hydrolysis was carried out with Novozymes’ Cellic CTec3 and/or Cellic HTec3, whereas fermentation was performed with Bacillus coagulans DSM2314. Water-washing of pretreated solids before enzymatic hydrolysis improved both hydrolysis and fermentation yields. The presence of xylo-oligosaccharides (XOS) in substrate hydrolysates reduced hydrolysis efficiency, but their effect on fermentation was negligible. The presence of fermentation inhibitors in C5 streams was circumvented by adsorption on activated carbon powder with no detectable sugar losses. High carbohydrates-to-LA conversions (Yp/s) of 0.88 g·g-1 were obtained from enzymatic hydrolysates of water-washed steam-exploded materials that were produced at 195°C, 7.5 min and the use of centrifuged-but-never-washed pretreated solids decreased Yp/s by 16%. However, when the detoxified C5 stream was added at a 10% ratio, Yp/s was raised to 0.93 g·g-1 for an LA productivity of 2.55 g·L-1·h-1. Doubling the pretreatment time caused a decrease in Yp/s to 0.78 g·g-1, but LA productivity was the highest (3.20 g·L-1·h-1). For pretreatment at 195°C for 7.5 min, elimination of water washing seemed feasible, but the use of longer pretreatment times made it mandatory to eliminate fermentation inhibitors.

Current study aims to evaluate the possibilities to increase part strength by optimizing the FFF process parameters. Five different CAD models of parts with same coupling dimensions but different shape inherited from a recent study were converted into test samples with Ultimaker 2 3D printer. The main measure of success was the sample strength, defined as the load at which the first crack in the stressed area of the part appeared. Three different modifications to the FFF process with verified positive effect on interlayer bonding were applied. First modification included raising the extrusion temperature and disabling printed part cooling. Second modification consisted in reduction of the layer thickness. Third modification combined the effects of the first and the second ones. For four out of five shapes tested applied process modifications resulted in significant strengthening of the part. The shape that exhibited the best results was subject to further research by creating special printing mode. The mode included fine-tuning of three technological parameters on different stages of the part fabrication. As result it was possible to increase the part strength by 108% only by tuning printing parameters of the best shape designed with increasing its weight by 8%.

The aim of this study was to assess the effect of added cultures of probiotic lactic acid bacteria on physicochemical, textural, and sensory characteristics of fresh cheese as well as their viability. Probiotic strains Lactobacillus acidophilus and L. rhamnosus were evaluated at two inoculation times (before the renneting and salting processes) following a factorial treatment arrangement. The bacterial count (log CFU g-1), acidity determination (% lactic acid), pH and percentage of syneresis were evaluated at 0, 1, 7, 14 and 21 days of refrigerated storage (4–5 °C). The texture profile analysis and an extended preference test were carried out at 21 days of storage. At the end of storage, fresh cheeses containing L. rhamnosus, added prior to the renneting process, had similar acidity values (0.18% lactic acid), pH (5.36) and percentage of syneresis (4.71%) compared to those for the cheeses without probiotics or control. Excluding adhesiveness, no differences were observed in texture profile parameters among the assessed cheeses. The fresh cheese supplemented with L. rhamnosus before the renneting process had a microorganism count greater than 6 logarithmic cycle/g, and the highest preference among treatments. The results from this study suggest that fresh cheese can be an excellent matrix for probiotic microorganisms, in particular L. rhamnosus.

Poly(acrylic acid) (PAAc) hydrogels possess good bioadhesive properties and allow enhanced penetration of drugs. In addition, it is possible to localize the absorption site of the drug in the hydrogel and increase the drug residence time. As opposed to other cross-linking processes radiation-induced polymer cross-linking can be easily and rapidly carried out without the use of cross-linking agents and other chemical additives. In this study, we fabricated metronidazole (MD) containing PAAc hydrogel (MD/PAAc) with different MD contents (0.1, 0.25, 0.5 wt%) using varying radiation doses (25, 50, 75 kGy) by gamma-irradiation. The physical and thermal properties were determined by gel content analysis, swelling ratio measurements, compressive strength measurements, differential scanning calorimetery, and thermogravimetric analysis. The properties of the hydrogel degraded due to the crystalline nature of MD. The properties of the hydrogel degraded due to the crystalline nature of MD. Cumulative release observed after 50 min in the case of 0.5MD/PAAc and 0.1MD/PAAc was 50% and 10%, respectively. Our findings suggest that MD/PAAc could be a suitable drug delivery carrier for use with radiation-based techniques.

We evaluated the change in water dispersibility of lactic acid bacteria (LAB, Enterococcus faecalis KH2) upon powderization and its influence on their efficacy. When cultured LAB are washed, heat-killed, and powdered, adhesion between LAB occurs and they form aggregation (non-treated LAB, n-LAB). However, a dispersed LAB (d-LAB) powder with less aggregates can be prepared by treating them with a high-pressure homogenizer and adding an excipient during powdering. n-LAB or d-LAB was administered to mice and the Peyer's patches in the small intestine were observed. n-LAB administration showed a high amount of aggregated LAB drifting in the intestinal mucosa, whereas d-LAB reached the Peyer's patches and was taken up into the Peyer's patches. Evaluation in a mouse influenza virus infection model showed that d-LAB was more effective than n-LAB in influenza yield of bronchoalveolar lavage fluids (BALFs) on day 3 post-infection, neutralizing antibody titers of sera and influenza virus-specific IgA in the feces on day 14 post-infection. Thus, the physical properties of LAB affect their efficacy; controlling their water dispersibility can improve their effectiveness.

An exploratory Life Cycle Assessment was carried out to provide insight into the environmental impacts of using the green seaweed Ulva spp. as a feedstock for production of bioplastic. The study focused on the production of lactic acid as a precursor of polylactic acid. The studied production process consists of (1) the cultivation of Ulva spp. in Integrated Multitrophic Aquaculture, (2) the processing of the biomass for solubilisation of sugars, (3) the fermentation of the sugars to lactic acid and (4) isolation of lactic acid from the fermentation broth. The study identifies environmental hotspots and compares the experimental seaweed production chain with conventional feedstock. The main hotspot identified is electricity consumption during seaweed cultivation. This impact of electricity consumption can be lowered by reducing energy use and sourcing renewable energy, and by improving the material efficiency in the product chain. To improve understanding of the environmental impacts of the production process, future studies can broaden the system boundaries and broaden the scope of sustainability issues included in the environmental assessment.

Abstract: This paper outlines the methodology and results for a two species finite volume scalar computational drug transport model developed for simulating the mass transport of Poly(lactic-co-glycolic acid (PLGA) ) from a half-embedded single strut implanted in a coronary arterial vessel wall. The mathematical drug transport model incorporates the convection-diffusion equation in scalar form (dimensionless) with a two species (free-drug and bound-drug) mass transport setup including reversible equilibrium reaction source terms for the free and bound-drug states to account for the pharmaco-kinetic reactions in the arterial wall. The relative reaction rates of the added source terms control the interconversion of drug between the free and bound-drug states. The model is solved by a 2-D finite-volume method for discretizing and solving the free and bound drug transport equations with anisotropic vascular drug diffusivities. This model is an improvement over our previously developed model using the finite-difference method. A dimensionless characteristic scaling pre-analysis was conducted a priori to evaluate the significance of implementing the reaction source terms in the transport equations. This paper reports the findings of an investigation of the interstitial flow profile into the arterial wall and the free and bound drug diffusion profiles with a parametric study of varying polymer drug concentration (low and high), tortuosity, porosity, and Peclet and DamKöhler numbers over the course of 400 hours (16.67 days). The results also reveal how a single species drug delivery model that neglects both a reversible binding reaction source term and the porosity and tortuosity of the arterial wall cannot accurately predict the distribution of both the free and bound drug.

This mini-review provides an overview of traditional, emerging, and future applications of lactic acid bacteria (LAB) and discusses how genome editing tools can be used to overcome current challenges in all these applications. It also describes currently available tools and how these can be further developed, and takes current legislation into account. Genome editing tools are necessary for the construction of strains for new applications and products, but can also play a crucial role in traditional ones, such as food and probiotics, as a research tool for understanding mechanistic insights and discovering new properties. Traditionally, recombinant DNA techniques for LAB have strongly focused on being food-grade, but they lack throughput and the number of genetically tractable strains is still rather limited. Further tool development in this direction will enable rapid construction of multiple mutants or mutant libraries on a genomic level in a wide variety of LAB strains. We also propose an iterative Design-Build-Test-Learn workflow cycle for LAB cell factory development based on systems biology, with “cell factory” expanding beyond its traditional meaning of production strains and making use of high-throughput genome editing tools to advance LAB understanding, applications and strain development.

Solid-state fermentation (SSF) is the bioprocess where microorganisms are cultivated in the absence of free water under control conditions. Lactic acid can be produced by fermenting grape stalks with Rhizopus oryzae in SSF. During the microorganism growth, the temperature and water content of the solid bed fluctuate, leading to areas of either dry or excessive moisture in the solid substrate. Therefore, it's crucial to control the supply of water to the matrix. In this work, we obtain lactic acid through SSF of grape stalks using Rhizopus oryzae NCIM 1299. The SSF was conducted at a fixed temperature of 35 °C, with three constant relative humidity levels: 50, 65, and 80 %RH. Mathematical models, including the Logistic and First Order Plus Dead Time models for fungal biomass growth and the Luedeking and Piret with Delay Time model for lactic acid production, were adjusted to kinetic curves. Growth kinetic parameters (Xmax, μmax, Tp, T0, Yp/x and td) were determined for all conditions. These kinetic parameters were then correlated with relative humidity using a second-degree polynomial relationship. We observed a decrease in Xmax with increasing %RH, while the value of Yp/x increased at higher %RH. Finally, the optimal variable relative humidity profile was obtained by applying the Dynamic Optimization Technique, resulting in a 15.30% increase in lactic acid production.

Lactic acid bacteria (LAB) have an extracellular proteolytic system that includes a multi-domain, cell envelope protease (CEP) with a subtilisin homologous protease domain. These CEPs have different proteolytic activities despite having similar protein sequences. Structural characterization has previously been limited to CEP homologs of dairy and human derived LAB strains, excluding CEPs of plant derived LAB strains. CEP structures are a challenge to determine experimentally due to their large size and attachment to the cell envelope. This study aims to clarify the prevalence and structural diversity of CEPs by using the structure prediction software AlphaFold 2. Domain boundaries are clarified based on a comparative analysis of 21 three-dimensional structures, revealing novel domain architectures of CEP homologs that are not necessarily restricted to specific LAB species or ecological niches. The C-terminal flanking region of the protease domain is divided into fibronectin type-III-like domains with various structural traits. The analysis also emphasizes the existence of two distinct domains for cell envelope attachment that are preceded by an intrinsically disordered cell wall spanning domain. The domain variants and their combinations provide CEPs with different stability, proteolytic activity and potentially adhesive properties, making CEPs targets for steering proteolytic activity with relevance for both food development and human health.

In the current study, the physicochemical and microbiological characteristics of this fermented wheat Hamoun were described in detail, as well as the soil properties where this type of wheat was stored. The results showed that the Hamoum had concentrations of the lactic acid of 0.25 g ± 0.03 for the Simeto variety (nine years of storage), as well as 0.13 g ± 0.02 and 0.17 g±0.06 for the Ofanto variety following three and six months, respectively, of storage. The water content varied between 8.3 - 9.7 % for grain and between 10.8- 11.5 % for flour. The ash content of grain and flour of 1.43 ± 0.02 and 1.63 ± 0.26, respectively, was above the normal standards. According to these results, fermented wheat is appropriate for human consumption. The results also showed that the soil where the wheat was stored comprised mainly clay and had an alkaline pH of 8.2. The isolation and identification of fermentable germs showed the presence of lactic acid bacteria belonging to the genera Lactobacillus (59 %), Pediococcus (18 %), Leuconostoc (17 %), and Streptococcus (6 %). The antibacterial activities of isolated acid bacteria against pathogenic germs Escherichia coli (ATCC 25922), Pseudomonas aeruginosa (ATCC 9027), Bacillus cereus (ATCC 14579), and Staphylococcus aureus (ATCC 43300) reflected the presence of strong antibacterial activity, with 62.5 % positive interactions and 100 % pathogenic bacteria inhibited by Lactobacillus.

Animal products, in particular dairy and fermented products, are natural, major sources of lactic acid bacteria (LAB). Due to their antimicrobial properties, LAB are used in humans and in animals, with beneficial effects, as probiotics or in the treatment of a variety of diseases. In livestock production, LAB contribute to animal performance, health, and productivity. In the food industry, LAB are applied as bioprotective and biopreservation agents, contributing to improve food safety and quality. However, some studies have described resistance to relevant antibiotics in LAB, with the concomitant risks associated to the transfer of antibiotic resistance genes to foodborne pathogens, their potential dissemination throughout the food chain, and the environment. Here, we summarize the application of LAB in livestock and animal products, as well as the health impact of LAB in animal food products. In general, the beneficial effects of LAB on the human food chain seem to outweigh the potential risks associated with their consumption as part of animal and human diets. However, further studies and continuous monitorization efforts are needed to ensure their safe application in animal products and in the control of pathogenic microorganisms, preventing the possible risks associated with antibiotic resistance and, thus, protecting public health.

In this work, the apparent shear strength at the interface between a bamboo fiber and the surrounding poly(lactic acid) (PLA) matrix is quantified. A method for processing pull-out test samples within a controlled embedded length is proposed and the details of the test procedure are presented, along with a critical discussion of the results. Two series of samples are considered: untreated and mercerized bamboo fibers from the same batch, embedded in the same polyester matrix. Electron and optical microscopy are used to observe the fiber-matrix interface before and after the test, and to identify the failure mode of each sample, especially as regards the occurrence of fibrillation in the fiber bundles. The values of apparent interfacial shear strength are calculated only for regular fibers successfully pulled out from the matrix, and reported with their statistical variations. Mercerization, whose efficiency was proven by Fourier Transform InfraRed (FTIR) spectroscopy, did not appear though to improve the quality of the interface (τ_app = 7.0 ± 3.1 MPa for untreated fibers and τ_app = 5.3 ± 2.4 MPa for treated fibers).

Alheira is a naturally fermented meat sausage traditionally made in the Portuguese region of Trás-os-Montes. Lactic Acid Bacteria (LAB) have been found to be the dominant microorganisms in alheira. This study aimed: 1) to characterize technological features and in vitro antimicrobial activity of LAB isolates; and 2) to reveal associations between such phenotypic characteristics and the isolates genotypically identified to species level through amplification and sequencing of the 16S ribosomal gene. Sixty-two LAB isolates were identified and Enterococcus faecium was the most prevalent (32.3%), followed by Leuconostoc mesenteroides (19.4%) and Latilactobacillus sakei (17.7%), aligning with previous research on traditional Portuguese fermented meat sausages. The phenotypic analysis of LAB isolates indicated diverse acidification capacities, proteolytic activities, and inhibitory effects against foodborne pathogens. Comprising the technological attributes, L. paracasei and L. mesenteroides had higher proteolytic activity (3.46 and 3.43 mm), whereas E. faecium and L. paracasei stood out for their acidifying capacity, with mean pH after 6 h of 5.78 and 6.03, respectively. Overall, lactobacilli presented higher inhibition diameter against the pathogens Staphylococcus aureus, Listeria monocytogenes and Salmonella Typhimurium. Although the mechanisms for inhibition of pathogen growth needs to be further elucidated, these findings enhance our understanding of LAB diversity and functionality in alheira sausages, contributing to product safety and quality assessment.

Pozol is a Mexican beverage prepared from fermented nixtamalized maize dough. To contribute to understanding its complex microbial ecology, the effect of inoculating on MRS-starch pure and mixed cultures of amylolytic Sii-25124 and non-amylolytic W. confusa 17, isolated from pozol, were studied on their interactions and fermentation parameters. These were compared with L. plantarum A6, an amylolytic strain isolated from cassava. Microbial growth, kinetic parameters, amylolytic activity, lactic acid production, and hydrolysis products from starch fermentation were measured. The population dynamics were followed by qPCR. L. plantarum A6 showed higher enzymatic activity, lactic acid, biomass production, and kinetic parameters than pozol LAB in pure cultures. Mixed culture of each pozol LAB with L. plantarum A6 showed a significant decrease in amylolytic activity, lactic acid yield, specific growth rate, and specific rate of amylase production. The interaction between Sii-25124 and W. confusa 17 increased the global maximum specific growth rate (µ), the lactic acid yield from starch (Ylac/s), lactic acid yield from biomass (Ylac/x), and specific rate of lactic acid production (qlac) by 15, 30, 30, and 40%, respectively compared with the pure culture of Sii-25124. Interactions between the two strains are essential for this fermentation.

This mini-review deals with some non-starter lactic acid bacteria (NSLAB) species with a controversial nature known to be both human and animal pathogens but also health-promoting and probiotic. The focus is put on Lactococcus garvieae, two Streptococcus species (Str. uberis and Str. parauberis), four Weissella species (W. hellenica, W. confusa, W. paramesenteroides and W. cibaria) and Mammalicoccus sciuri which worldwide are often found within the microbiotas of different kinds of cheese, mainly traditional artisanal ones made from raw milk and/or relying on environmental bacteria for their ripening. Based on literature data, their virulence and health-promoting effects are examined, and some of the mechanisms of these actions are investigated. Additionally, their possible roles in cheese ripening are also discussed. The analysis so far showed that, in general, the pathogenic and the beneficial strains, despite belonging to the same species, show pretty different genetic constitutions. Yet, when the safety of a given strain is assessed, genomic analysis on its own is not enough, and a polyphasic approach is needed including additional physiological and functional tests.

This study focused on the characterization of lactic acid bacteria (LAB) in a renowned traditional Italian cheese, Pecorino di Farindola, to select an autochthonous culture and investigate its po-tential for the improvement of safety and functional properties. Two hundred and six LAB isolated throughout production and maturation from nine cheese lots of three farms were identified by 16S rRNA gene sequencing and tested for the presence of genes encoding virulence factors, vancomycin resistance (for enterococci), biogenic amines (BAs) and bacteriocin production, for antimicrobial activity, and for the capacity to survive in the gastro-intestinal tract (GIT) based on tolerance to low pH and bile salts and adhesion to CaCo-2 cells. A Lacticaseibacillus paracasei isolate was used in cheese making and determined a decline of spiked Listeria monocytogenes and Escherichia coli O157 faster than in control cheese. The autochthonous bacterial groups were numerically unaffected, apart from lactobacilli that were recovered in higher numbers in the cheese with added L. paracasei. Based on Repetitive Extragenic Palyndrome (Rep) PCR profiles, the added strain possibly dominated until day 88 in cheese. Results encourage further trials with autochthonous cultures to efficiently inhibit hazardous bacteria and enrich a functional microbiota in Pecorino di Farindola and similar cheeses.

This study was aimed at investigating the protective effects of glass ionomer cement (GIC) and surface pre-reacted glass ionomer (S-PRG) fillers used as dental restorative materials on demineralization of bovine enamel. GlasIonomer FX ULTRA (FXU), Fuji IX GP Extra (FIXE), CAREDYNE RESTORE (CDR) were used as GICs. PRG Barrier Coat (BC) was used as the S-PRG filler. They were incubated in a lactic acid solution (pH = 4.0) for 6 d at a temperature of 37 °C. The mineral was etched from the enamel surface, and a large number of Ca and P ions were detected in solution. The Al, F, Na, Sr, and Sr ions were released in GICs and S-RPG fillers. The Zn ion was released only in CDR and the B ion was released only in BC. The presence of apparent enamel prism peripheries was observed after 6 d of treatment for the group containing only enamel blocks. pH values for the FXU, FIXE, CDR, BC, and enamel block groups after 6 d were 6.5, 6.6, 6.7, 5.9, and 5.1, respectively. Therefore, the observed pH neutralization effect suppressed progression of caries due to the release of several ions from the restoratives.

Nanofibers are one of the most attractive materials that can modify functionalities for developing new kinds of specific applications, mainly used as a biomedical material. Herein, we designed and prepared the antibacterial nonwoven fiber mats of PLA and PLA composited with Ag nanoparticles by electrospinning. The effects of varying filler contents on their chemical, surface morphology, thermal, water absorbency, and antibacterial properties were investigated using FTIR, SEM/EDS, DSC, swelling ratio, and qualitative and quantitative antibacterial tests. FTIR and EDS spectra indicated that Ag nanoparticles were incorporated in the PLA without chemical bonding. SEM revealed that the average diameter of the PLA nanofibers containing the Ag nanoparticles was more significant than those without those particles. Besides, fiber diameters are proportionally the amount of Ag nanoparticle contents. DSC indicated that the Ag nanoparticles can be incorporated within the PLA-matrix without strongly affecting their thermal properties. Moreover, the crystallinity of the composite nonwoven fiber mats was higher than those of fiber mats in the neat PLA. Accordingly, the antibacterial activities revealed that all the composite nanofiber mats exhibited excellent against S. aureus and E. coli bacterial strains. In addition, in the cell toxicity study, all produced hybrids nonwoven fiber mats induced a reduction in cell viability for the L929 fibroblast cells. Our results suggest that the designed and prepared nonwoven fiber mats may have good potential for use in the biomedical field, particularly in wound dressing applications

In horses, there is an increasing interest in developing long-lasting drug formulations, with bi-opolymers as viable carrier alternatives in addition to their use as scaffolds, suture threads, screws, pins, and plates for orthopedic surgeries. This communication focuses on the prolonged biocompatibility and biodegradation of PLA, prepared by hot pressing at 180 ºC. Six samples were implanted subcutaneously on the lateral surface of the neck of one horse. The polymers remained implanted for 24 to 57 weeks. Physical examination, plasma fibrinogen, and the mechanical noci-ceptive threshold (MNT) were performed. After 24, 28, 34, 38, and 57 weeks, the materials were removed for histochemical analysis using hematoxylin-eosin and scanning electron microscopy (SEM). There were no essential clinical changes. MNT decreased after the implantation procedure, returning to normal after 48h. A foreign body response was observed by histopathologic evalua-tion up to 38 weeks. At 57 weeks, no polymer or fibrotic capsules were identified. SEM showed surface roughness suggesting a biodegradation process, with an increase in the average pore di-ameter. As in the histopathological evaluation, it was not possible to detect the polymer 57 weeks after implantation. PLA showed biocompatible degradation and these findings may contribute to future research in the biomedical area.

The brown seaweed Alaria esculenta is the second most cultivated species in Europe and it is therefore of interest to expand its application in developing food products. In this study, a lactic acid bacteria consortium (LAB consortium) consisting of three Lactiplantabacillus plantarum strains (relative abundance ~ 94%) and a minor amount of a Levilactobacillus brevis strain (relative abundance of ~ 6%) was investigated for its ability to ferment carbohydrates available in brown seaweed. The consortium demonstrated ability in fermenting glucose, mannitol, galactose, mannose, and xylose, of which glucose and mannitol were the most favored substrates; no growth was observed on fucose, mannuronic and guluronic acid. The consortium used different pathways for carbohydrate utilization and produced lactic acid as the main metabolite. In glucose fermentations, only lactic acid was produced, but use of mannitol as carbohydrate source, resulted in co-production of lactic acid, ethanol and succinate. Xylose fermentation resulted in acetate production. The consortium was also able to utilize laminari-oligosaccharides (DP 2-4), obtained after enzymatic hydrolysis of laminarin, and produced lactic acid as metabolite. The consortium could grow directly on A. esculenta, resulting in a pH decrease to 3.8 after 7 days of fermentation. Incubation of the same seaweed at corresponding conditions without inoculation resulted in spoilage of the seaweed by endogenous bacteria.

Recently, polyacetylene (PA) is receiving a renewed scientific attention because of its unique properties potentially useful also for non-electrical applications (e.g., hydrogen storage, drug delivery, adsorbent of organic compounds in aqueous systems, gas and liquid separation, oxygen absorbent in gas analysis, etc.). Poly(vinyl alcohol) (PVOH) is a very common type of polymer, widely exploited in different technological areas, and it can be used as a precursor for the PA synthesis. Here, a new scheme for a large-scale chemical synthesis of PA, based on a simple and low-cost PVOH dehydration reaction by absolute sulfuric acid, has been developed. In this process, PVOH, shaped in form of film, is dipped in absolute sulfuric acid (i.e., H₂SO₄ at 95-97%) and, after complete chemical-dehydration at room temperature, it is mechanically removed from the liquid phase by using a plastic sieve. This reaction leads to a complete PVOH film conversion to PA as it has been proved by infrared spectroscopy (ATR-mode). Indeed, the ATR spectrum of the reaction product included all characteristic absorption bands of PA. To the best of our knowledge, this very easy and effective PA synthesis method based on the PVOH chemical-dehydration reaction by absolute sulfuric acid has never been described in the literature.

β-cyclodextrin-based star polymers have attracted much interest because of their unique structures and potential biomedical and biological applications. Herein, we synthesized well-defined folic acid (FA)-conjugated and disulfide bond-linked star polymer ((FA-Dex-SS)-βCD-(PCL)14) acted as theranostic nanoparticles for tumor-targeted magnetic resonance imaging (MRI) and chemotherapy. Theranostic nanoparticles were obtained by loading doxorubicin (DOX) and superparamagnetic iron oxide particles (SPIO) were loaded into the star polymer nanoparticles to obtain ((FA-Dex-SS)-βCD-(PCL)14@DOX/SPIO) theranostic nanoparticles. In vitro drug release studies showed that approximately 100% of the DOX was released from disulfide bond-linked theranostic nanoparticles within 24 h under a reducing environment in the presence of 10.0 mM GSH. DOX and SPIO could be delivered into HepG2 cells efficiently, owing to folate receptor-mediated endocytosis process of the nanoparticles and GSH triggered disulfide-bonds cleaving.Moreover, (FA-Dex-SS)-βCD-(PCL)14@DOX/SPIO showed strong MRI contrast enhancement properties. In conclusion, folate-decorated reduction-sensitive star polymeric nanoparticles are a potential theranostic nanoparticle candidate for tumor-targeted MRI and chemotherapy.

In this work, we synthesized chitosan grafted-poly acrylic acid (CS-g-PA) through surface-initiated atom transfer radical polymerization (SI-ATRP). We also studied the adsorption process of copper and lead ions onto CS-g-PA surface. Adsorption equilibrium studies indicated pH 4.0 as the best pH for the adsorption process, while the maximum adsorption capacity for Pb2+ ions was 98 mg*g-1 and for Cu2+ was 164 mg*g-1, higher adsorption capacities than chitosan alone (CS), where Pb2+ was only 14.8 mg*g-1and Cu2+ was 140 mg*g-1, respectively. Furthermore, the adsorption studies indicated that Langmuir model describes all the experimental data. All these results suggest that the new CS-g-PA polymers had potential as adsorbent for hazardous and toxic metal ions produced by different industries.

The product of ozonolysis, Glycero-(9,10-trioxolane)-trioleate (ozonide of oleic acid triglyceride, [OTOA]), was incorporated into polylactic acid/polycaprolactone (PLA/PCL) blend films in the amount of 1, 5, 10, 20, 30, and 40% w/w. The morphological, mechanical, thermal and antibacterial properties of the biodegradable blend after the OTOA addition were studied. According to DSC and XRD data, the crystallinity degree of PLA/PCL+OTOA films tended to decrease with increase in OTOA content that could be explained by its plasticizing effect. Morphological analysis showed that the structure of the films with the OTOA concentration above 20% drastically changed. Specifically, the interface between the PLA/PCL matrix and OTOA was formed, thereby forming a capsule with the embedded antibacterial agent. The moisture permeability of the resulting PLA/PCL+OTOA films decreased due to the formation of uniformly distributed hydrophobic amorphous zones that prevents water penetration. This architecture affects the tensile characteristics of the films: strength decreases to 5.6 MPa, elastic modulus E by 40%. The behavior of film elasticity is associated with the redistribution of amorphous regions in the matrix. Additionally, PLA/PCL+OTOA films with 20, 30 and 40% of OTOA showed good antibacterial properties on Pseudomonas aeruginosa, Raoultella terrigena (Klebsiella terrigena) and Agrobacterium tumefaciens. Developed PLA/PCL+OTOA films could be used as packaging materials and wound dressings. By variation of the OTOA content, it is possible to tailor the physical-chemical and antibacterial properties of the developed films for various applications.

The aim of the study was to evaluate the impact of probiotics obtained from agro-industrial substrates fermented with lactic acid bacteria and/or yeasts on the health and changes in the microbiota of the digestive tract of guinea pigs. Eighty male guinea pigs, Kuri breed, 30 days old and 250 g live weight, were randomly selected and divided into four groups of 20 animals each. T0, Control, T1, Lactobacillus acidophilus and L. bulgaricus. T2, Saccharomyces cerevisiae and Kluyveromyces fragilis and T3. L acidophilus, L bulgariccus, S cerevisiae and K. fragilis. T1, T2 and T3 contained molasses-vinasse substrate in their base, the dose administered was 0.75 mL/animal orally. The parameters evaluated were weight gain, occurrence of diarrhea and mortality, blood profile, macroscopic lesions in the digestive tract organs and changes in the microbiota of the stomach, caecum, small and large intestine. Treatments T1, T2 and T3 improved weight gain (p<0.05) and reduced the presence of guinea pigs with diarrhea (p<0.05) and there was no mortality; hematic indices did not vary significantly (p>0.05) between treatments; animals in the control group presented a greater amount (p<0.05) of macroscopic lesions in the digestive tract organs; in the T1, T2 and T3 group there was an improvement in the natural microbiota. It is concluded that the inclusion of microbial additive in young guinea pigs improves intestinal health, consequently, improves weight gain, reduces diarrhea and deaths, and normalizes the natural microbiota of the gastrointestinal tract.

Colon cancer is a common malignancy of digestive tract and has high incidence and mortality worldwide. As a normal flora in the human gastrointestinal tract, lactic acid bacteria have been proved to have health benefits, such as immune-regulation, anti-infection, and anti-tumor. In the present study, the inhibitory effects of 19 heat-inactivated plant-derived lactic acid bacteria on human colon cancer cell HCT116 were investigated. The results showed that heat-inactivated plant-derived lactic acid bacteria strain 729 had the strongest inhibitory effect on HCT116 cells among all tested bacteria. Treatment with heat-inactivated bacteria strain 729 could inhibit the proliferation of HCT-116 cells in dose-dependent manner, with 54.52% inhibition at a final concentration of 1×10⁸ CFU/mL. Moreover, the heat-inactivated bacteria strain 729 could block the cell cycle, induce apoptosis, and promote cellular ferroptosis by downregulating the expression of GPX4 and xCT at protein level. According to the 16S rDNA sequencing, the plant-derived lactic acid bacteria strain 729 was Lactobacillus plantarum. Collectively, the results indicates that lactic acid bacteria strain 729 may be developed as special ingredients targeting colon cancer, but further in vivo studies are required.

In this study, the effect of extraction conditions on the total phenolic content of clove buds was investigated. Clove buds were extracted using a deep eutectic solvents like mixtures choline chloride: lactic acid in the 1:2 molar ratio. Additionally, the HPLC-DAD method was used to determine the main components of the clove extracts, including eugenol, eugenol acetate, and β-caryophyllene. The conditions used in the extraction with choline chloride: lactic acid (molar ratio 1:2) included extraction temperature (t = 40 – 80°C), water addition (5.6 – 40%), and extraction time (30 – 90 min). Determination of the phenolic compounds was done by the Folin-Ciocalteu method. The optimum operating conditions for the total phenolic content were identified at 77°C, 30 min, and a water addition of 40%. Based on the results, the highest amount of eugenol (307.26 ± 8,44 mg/g dry raw material) was determined in clove extracts which were extracted under condition of 60°C, 22.8%, and 30 min.

The growth of two pairs of co-cultures (Escherichia coli/Geotrichum candidum, and Staphylococcus aureus/Geotrichum candidum) with a starter culture of lactic acid bacteria was studied in milk at temperatures related to artisanal cheesemaking ripening. For an inoculum of approximately 106 CFU/mL, LAB not only induced an early stationary phase of E. coli (two strains BR and PS2) and S. aureus (strains 2064 and 14733) but affected their death phase. G. candidum was found to be the subject of interactions with LAB within a given temperature range only partially. To develop a tertiary model for the growth curves of the populations, a one-step approach was used, combining two types of primary models (Huang and Gimenez and Dalgaard) with secondary square root models for growth rate and lag time. Furthermore, the reparametrized Gompertz-inspired function with the Bigelow secondary model was used to describe the death phase of the E. coli and S. aureus strains. The prediction ability of the growth of the H-GD tertiary model for co-cultures was cross-validated within the strains and data sets in milk and milk medium with 1 % NaCl.

The crystal nucleation and overall crystallization kinetics of cross-linked poly(ε-caprolactone) was studied experimentally by fast scanning calorimetry in a wide temperature range. With an increasing degree of cross-linking, both the nucleation and crystallization half-times increase. Concurrently, the glass transition range shifts to higher temperatures. In contrast, the temperatures of the maximum nucleation and the overall crystallization rates remain the same independent of the degree of cross-linking. The cold crystallization peak temperature generally increases as a function of heating rate, reaching an asymptotic value near the temperature of the maximum growth rate. A theoretical interpretation of these results is given in terms of classical nucleation theory. In addition, it is shown that the average distance between the nearest cross-links is smaller than the estimated lamellae thickness, which indicates the inclusion of cross-links in the crystalline phase of the polymer.

Background: While intimate feminine hygiene products are widely used by women as part of daily cleansing routines, little is known about how these products impact the vulvovaginal area and its microbiome stability. A novel gel wash containing lactic acid (pH 4.2) for external daily use was formulated to provide gentle cleansing, freshness, and antimicrobial protection to maintain a healthy balance of the vulvar skin area. This 4-week clinical study assessed tolerance of the gel wash when used on the external genital area and its effects on skin hydration, vulvar skin pH, and the vulvar microbiome. After a 7-day pre-study conditioning period, 36 healthy females in 3 balanced age groups (18-29, 30-44, and 45-55 years) used the gel wash to cleanse their external genital area (mons pubis and vulva) and entire body at least once per day for 28 days. The primary endpoint wasSkin tolerance of the gel wash was assessed by the gynecologist. Effects of the gel wash on vulvar skin microbiota were studied by performing bacterial 16S rRNA and fungal ITS microbial richness and diversity analysis. Results: Based on gynecologic assessment after 28 days of use, the gel wash showed acceptable tolerance, with no signs of increased dryness, redness, edema, itching, stinging, or burning. Use of the gel wash was associated with a significant increase in both short-term (single application) and longer-term (daily use for 28 days) skin moisturization. There was no significant change in vulvar skin pH over time with daily product use, and the gel wash did not significantly affect the natural vulvar microbiome species richness or diversity for bacteria or fungi. Conclusions: Results of the study showed that this new gel wash is a mild, moisturizing cleanser that does not harm and instead maintains the natural pH and microbial diversity of vulvar skin. To our knowledge, this was the first study to assess the effect of an antimicrobial feminine gel wash on the natural pH and vulvar microbiome habitat of the skin using bacterial 16S rRNA and fungal ITS genetic sequencing techniques, thereby providing a better understanding of the bacterial and fungal communities that inhabit the external vulvar area in healthy women.

The effects of orally administered lactic acid bacteria metabolites on the skin were studied using an atopic dermatitis-like murine model created by feeding mice with HR-AD. The lactic acid bacteria metabolites were obtained by inoculating 35 strains of 16 species of lactic acid bacteria into soy milk and culturing them. The atopic dermatitis-like murine model was created by feeding HR-1 mice HR-AD for 40 days. The skin condition of mice that were fed HR-AD worsened compared with normal mice, i.e., reduced water content in the stratum corneum, increased transepidermal water loss (TEWL), reduced ceramide AP content in the stratum corneum, and increased epidermis thickness. When mice that had been fed the HR-AD diet was administered a raw liquid of lactic acid bacteria metabolites orally, the measured values related to water content in the stratum corneum, TEWL, ceramide AP content in the stratum corneum, and epidermis thickness improved. To find out the active components for these effects, filtrate and residue from the raw liquid of lactic acid bacteria metabolites and lipid components extracted from the raw liquid were examined at the same time. Results showed that the water-soluble components or residue after filtration did not demonstrate effects but the raw liquid and the lipid fraction did. These findings suggest that lactic acid bacteria metabolites improve skin injury in an atopic dermatitis-like murine model.

N,N-dimethyl-4-nitroaniline (NNDM4NA, C8H10O2N2), is a superelastic and superplastic charge-transfer molecular crystal with a high molecular dipole moment, µ=7.95 D, which crystal-lizes in the acentric polar point group 2. Highly aligned poly-l-lactic acid (PLLA) polymer micro-fibers with embedded NNDM4NA nanocrystals were fabricated using the electrospinning tech-nique. The composite fibers display an extraordinarily high piezoelectric output response, where for a small stress of 5.0x103 Nm-2, an effective piezoelectric voltage coefficient of geff=3.6 VmN-1 was obtained. The fibers were found to display solid state blue fluorescence with a long (147 ns) life-time decay. Furthermore, the composite fibers exhibit an average increase of 67% on the Young modulus reaching 55 MPa, while the tensile strength reaches 2.8 MPa when compared with solely PLLA fibers. The results show that nanocrystals, from small organic molecules, with elastic and piezoelectric properties form hybrid functional 2-dimensional luminescent array which are me-chanical strong and generate high output voltages making them promising for applications in energy harvesting and as solid-state blue emitters.

Concentration and preservation of lactic acid bacteria (LAB) starter cultures for food production guarantee the long-term delivery of stable cultures in terms of viability and functional activity. One method that has commonly been used to prepare dried starter cultures for food applications is freeze-drying. During freeze-drying, the bacterial cells are exposed to stresses such as freezing, drying, and long-term exposure to low-water activity. Additionally, another added stress is introduced during the rehydration process. The purpose of this study was to evaluate the survival rates and fermentation performance of three (3) freeze-dried lactic acid bacterial cultures previously isolated from Ghanaian traditional fermented milk. LAB cultures, i.e., Lactobacillus delbrueckii, Lactococcus lactis and Leuconostoc mesenteroides were frozen in the chamber of a Telstar (Lyoquest) laboratory freeze dryer for 10 hrs at -55 °C (as single and combined cultures) using skimmed milk and cassava flour as cryoprotectants held in plastic or glass cryovial. For viability during storage, freeze-dried LAB cultures were stored in a refrigerator (4 °C) and at room temperature (25 °C) for 4-weeks. The survival of freeze-dried cultures was determined by growth kinetics at 600nm (OD₆₀₀). The performance of freeze-dried LAB cultures after 4-weeks storage was determined by their growth and acidification of milk during yogurt fermentation and consumer sensory evaluation of fermented milk using a 9-point hedonic scale. The survival rates for LAB ranged between 60.11% and 70.91% following freeze-drying. For single cultures, the highest survival was recorded for Lactobacillus delbrueckii (L12), whereas for combined cultures, the highest survival was observed for Lactococcus lactis (L3) combined with Lactobacillus delbrueckii (L12). During the fermentation process all the freeze-dried LAB cultures were able to acidify yogurt to a pH below 4, while yogurt produce from the spontaneous fermentation was characterized by low acidification. Yogurt fermented with freeze-dried lactic acid bacteria cultures, either single or combined strains, showed improved acceptability as compared to the spontaneously fermented yogurt. The consumer acceptability results showed that yogurts produced with combined starter culture of Lactoccus lactis and Lactobacillus delbrueckii or single culture of Lactococcus lactis were the most preferred products with Lactococcus lactis and Lactobacillus delbrueckii possessing high survival rates and high consumer acceptability in yogurt production. These findings are crucial and can be adopted for large-scale production and commercialization of yogurt production, however, in-depth investigation on the effects of freeze-drying and long-term storage on survival and performance of selected LAB cultures are needed.

Wet anaerobic storage of algal biomass is a promising preservation approach which can ensure continuous supply of these feedstocks to biorefineries year-round. An effective solution to preservation must ensure minimal dry matter loss and change in biochemical composition during storage. Therefore, the objective of this study was to investigate the preservation of Nannochloropsis gaditana biomass through wet anaerobic storage and its impact on biomass quality. Prior to storage, algae sample was inoculated with two different strains of lactic acid bacteria and thereafter stored for 30 and 180 days. Each inoculant limited dry matter loss to &lt;10% (dry basis) after the storage durations. Final pH values (4.3 - 4.8) indicate that the biomass samples were properly ensiled, achieving the acidic conditions necessary for preservation. Compositional analysis of the biomass after storage showed a reduction in carbohydrate content, a relative increase in lipid content, and no significant change to the protein fraction. Glucose and galactose were the prevalent sugar monomers. The low dry matter loss and minimal compositional change indicates that wet anaerobic storage is an effective means of preserving algal biomass, ensuring a constant supply of algal biomass feedstock to a biorefinery.

Salmonella infections can lead to intestinal inflammation and metabolic disorders in birds. However, whether ARA metabolism is involved in Salmonella-induced intestinal inflammation remains unclear. This experiment investigated the changes in cecal flora and arachidonic acid (ARA) metabolism in Hainan Wenchang chickens infected with S. Typhimurium using 16s rDNA sequencing and targeted metabolomics. The results showed that the levels of ARA metabolites were increased in the cecum tissue of Wenchang chickens after infection with S. Typhimurium, including prostaglandin E2, prostaglandin F2α, lipoxin A4, ±8(9)-EET, ±11(12)-EET, and ±8,9-DiHETrE. The content of key enzymes for ARA production and metabolism (PLA2 and COX-2) in chicken cecum tissues was increased after S. Typhimurium infection. The relative mRNA levels of inflammatory factors were also increased after infection, including IFN-γ, TGF-β1, IL-4, and IL-6. In HD11 cells, the use of a cyclooxygenase (COX) inhibitor reduced the increased levels of COX-2 and PGF2α induced by S. Typhimurium infection and effectively reduced the inflammatory response. In addition, the number of beneficial genera (e.g., Bifidobacterium, Lactobacillus, and Odorobacterium) in the cecum of Wenchang chickens was significantly reduced after infection with S. Typhimurium. In this study, we revealed the structure of the cecal flora of Wenchang chickens infected with S. Typhimurium and demonstrated that S. Typhimurium can mediate the onset and development of intestinal inflammation through the activation of the metabolic pathway of ARA cyclooxygenase in Wenchang chickens. The results can provide data support and theoretical support for the prevention and control of avian salmonellosis.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Elevated serum uric acid (sUA) is associated with risk of developing cardiovascular disease (CVD). Here, we examined the prognostic significance of sUA and exercise capacity in 411 Japanese adults (age, ≥65; mean, 81 years) hospitalized for worsening CVD. Mean sUA was significantly higher in the 23% of patients on an sUA-lowering agent than in those not. When the patients were stratified by sUA into three groups (7.0 mg/dL), the high sUA group had significantly worse peak VO2 and composite endpoint (rehospitalization due to worsening CVD and all-cause mortality) compared with low and moderate sUA groups (P < 0.001). When the patients were stratified by sUA into five groups (sUA 10.0 mg/dL), the incidence of the composite endpoint was significantly higher in the highest sUA group compared with that in the reference group, but only in women. Univariate Cox regression analysis, but not a multivariate analysis, indicated that sUA was significantly associated with the composite endpoint. Although sUA and exercise capacity may have some degree of prognostic significance in older patients with CVD, this significance may differ between men and women.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

Background: Microscopic examination of acid-fast stained sputum smears for detecting mycobacterial acid-fast bacilli (AFB) remains the most economical and readily available method for laboratory diagnosis of tuberculosis (TB). However, this conventional approach has limitations, including low sensitivity and labor-intensive procedures. Methods: An automated microscopy system incorporating artificial intelligence (AI) and machine learning for AFB identification was evaluated. The study was conducted at an Infectious Disease Hospital in Jiangsu Province, China, utilizing an intelligent microscope system (TB-Scan, Wellgen Medical, Kaohsiung). A total of 1,000 sputum smears were included in the analysis, with the system capturing digital microscopic images and employing an image recognition model to automatically identify and classify AFB. Referee technicians provided the gold standard for discrepant results. Results: The automated system demonstrated an overall accuracy of 95.00% (950/1,000), sensitivity of 91.24% (177/194), and specificity of 95.91% (773/806). Notably, the system identified 21 smears as positive that were previously reported as negative, with referee technicians confirming 17 of these as true positive and retracting the test results accordingly. Recalculating the performance, the accuracy increased to 96.70% (967/1,000), sensitivity to 91.94% (194/211), and specificity to 97.97% (773/789), with a false negative rate of 8.06% (17/211) and a false positive rate of 2.03% (16/789). Conclusions: The incorporation of AI and machine learning into an automated microscopy system demonstrated the potential to enhance the sensitivity and efficiency of AFB detection in sputum smears compared to conventional manual microscopy. This approach holds promise for widespread application in TB diagnostics and potentially other fields requiring labor-intensive microscopic examination.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

Beyond factors such as smoking and obesity, the risk of getting gastrointestinal cancer is passed down from parents to offspring, inherited by a gene mutation, predisposing them to develop cancer in their lifetime. Here we describe the clinical history of family members affected by gastrointestinal pathologies often leading to cancer. In the epidemiological study, the cohort of members of this family shared a high risk of developing gastrointestinal diseases. The subjects were monitored from May 2006 to December 2017 by collecting periodically clinical and endoscopic data, and determining both auto-modification of lymphocyte Poly(ADP-ribose)Polymerase as early signal of DNA damage, and erythrocyte membrane lipid composition (Fat Profile). Both biomarkers were demonstrated to be non invasive and easy tools, to monitor over time family members, first the oldest members (nine siblings), and thereafter their offspring, whose cell status evolved from physiological even to cancerous one. All subjects developed gastrointestinal pathologies of different kind and seriousness. Some diseases evolved to cancer, sometimes as a sudden and lethal event. The results of the two molecular approaches, agreed and even predicted the clinical and imaging paths. This cohort study supported the hypothesis that both noninvasive molecular analyses can predict altered cell states and support clinical and imaging tests.

High porosity and mass transport properties of microfiltration polymeric membranes benefits nutrients supply to cells when used as scaffolds in interstitial perfusion bioreactors for tissue engineering. High nutrients transport is assumed when pore size and porosity of the membrane are in the micrometric range. The present work demonstrates that the study of membrane fouling by proteins present in the culture medium, though not done usually, should be included in the routine testing of new polymer membranes for this intended application. Two poly(ε-caprolactone) microfiltration membranes presenting similar average pore size (~0.7µm) and porosity (>80%) but different external surface porosity and pore size have been selected as case study. The present work demonstrates that a membrane with lower surface pore abundance and smaller external pore size (~0.67 µm), combined with adequate hydrodynamics and tangential flow filtration mode is usually more convenient to guarantee high flux of nutrients. On the contrary, having large external pore size (~1.70µm) and surface porosity would incur in important internal protein fouling that could not been prevented with the operation mode and hydrodynamics of the perfusion system. Additionally, the use of glycerol in the drying protocols of the membranes might cause plasticization and a consequent reduction of mass transport properties due to membrane compaction by the pressure exerted to force perfusion. Therefore, preferentially, drying protocols that omit the use of plasticizing agents are recommended.

Mass transfer restrictions of scaffolds are currently hindering the development of three-dimensional (3D), clinically viable, and tissue engineered constructs. For this situation, a 3D poly(lactide-co-glycolide)/hydroxyapatite porous scaffold, which was much favorable for transfer of nutrients to and waste products from the cells in the pores, was developed in this study. The 3D scaffold had an innovative structure, including macropores with diameters of 300−450 μm for cell ingrowth and microchannels with diameters of 2−4 μm for nutrition and waste exchange. The mechanical strength in wet state was strong enough to offer the structural support. The typical structure was more beneficial for the attachment, proliferation, and differentiation of rabbit bone marrow mesenchymal stem cells (rBMSCs). The alkaline phosphatase (ALP) activity and calcium (Ca) deposition were evaluated on the differentiation of rBMSCs, and the results indicated that the microchannel structure was very favorable for differentiating rBMSCs into maturing osteoblasts. For repairing rabbit radius defects in vivo, there was rapid healing in the defects treated with the 3D porous scaffold with microchannels, where the bridging by a large bony callus was observed at 12 weeks post-surgery. Based on the results, the 3D porous scaffold with microchannels was a promising candidate for bone defect repair.

Introduction: Young adults are the second largest segment of the immigrant population in the United States (US). Given recent trends in later age of initiation of tobacco use, we examined variation in use of tobacco products by nativity status for this population group. Methods: Our study included young adults 18-30 years of age sampled in the National Health Interview Survey (2015-2019), a nationally representative sample of the US population. We calculated prevalence of use of any and 2 or more tobacco products (cigarettes, cigars, pipes, e-cigarettes, and smokeless tobacco) for foreign-born (n=3,096) and US-born (n=6,811) young adults. Logistic regression models adjusted for age, sex, race-ethnicity, education, and poverty, while accounting for the complex survey design. Results: Foreign-born young adults were significantly less likely to use any tobacco product (Cigarette = 7.3% vs 10.7%; Cigar= 1.8% vs 4.8%; E-cigarette= 2.3% vs 4.5%, respectively; p<0.01) or poly tobacco use (1.9% vs. 4.2%; p<0.01) than US-born young adults. Adjusted regression models showed lower odds of poly tobacco use among the foreign-born than their US-born counterparts (Odds Ratio = 0.41, (95% Confidence Interval: 0.26-0.63)). Conclusion: Findings highlight the importance of targeted interventions by nativity status and further tobacco prevention efforts needed for the US-born.

The term Conjugated Linoleic Acid (CLA) refers generically to a class of positional and geometric conjugated dienoic isomers of linoleic acid. Among the isomers of linoleic acid cis9, trans11-CLA (c9, t11-CLA) and trans10, cis12-CLA (t10, c12-CLA) are found to be bio-logically active isomers, and they occur naturally in milk, dairy products and meat from ruminants. In addition, some vegetables and some sea-foods have also been reported to contain CLA. Although the CLA levels in these natural sources are insufficient to confer the essential health benefits, anti-carcinogenic or anti-cancer effects are of current interest. In the rumen, CLA is an intermediate of isomerization and the biohydrogenation process of linoleic acid to stearic acid conducted by ruminal microorganisms. In addition to rumen bacteria, some other bacteria, such as Propionibacterium, Bifidobacterium and some lactic acid bacteria (LAB) are also capable of producing CLA. In this regard, Lactiplantibacillus plantarum (formerly Lactobacillus plantarum) has demon-strated the ability to produce CLA isomers from linoleic acid by multiple enzymatic activi-ties, including hydration, dehydration, and isomerization. L. plantarum is one of the most versatile species of LAB and the bacterium is widely used in the food industry as a micro-bial food culture. The studies reviewed in this article reveal how, in the production of some fermented foods, the use of appropriate strains of L. plantarum, as a starter or additional culture, can be considered a critical factor in the design of new CLA-enriched functional foods.

A bridged 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) derivative (PN-DOPO) in combination with aluminum phosphates coated sepiolite (Sep@AlPO4) was used to improve the flame retardancy, thermal stability and mechanical properties of poly (ethylene oxide) (PEO)/poly (butylene adipate-co-terephthalate) (PBAT) blends. The synergistic effects of PN-DOPO and Sep@AlPO4 on the fire resistance, thermal decomposition behavior and mechanical properties of PEO/PBAT composites were investigated systematically. The results indicated that 5 wt % Sep@AlPO4 combined with 10 wt% PN-DOPO into PEO/PBAT achieved a V-1 rating in UL-94 test and the LOI value increased to 23.7%, meanwhile, the peak-heat release rate (p-HRR), av-HRR and total heat release (THR) values of PEO/PBAT/PN10%/Sep5% composites decreased by 35.6%, 11.0% and 23.0% compared with those of PEO/PBAT, respectively. The thermogravimetric analysis (TGA) results confirmed that PN-DOPO/Sep@AlPO4 could enhance the initial thermal stability and char yield of PEO/PBAT matrix, and TGA/Fourier transform infrared spectrometry (TGA-FTIR) results revealed that the composites exhibited the absorption peaks of phosphorous-containing groups and an increase in gas-phase volatiles during the thermal decomposition process. The digital photographs and morphological structures of char residues demonstrated that PN-DOPO and Sep@AlPO4 mixtures benefited to the formation of a more continuous and dense carbon layer on the composites surface during combustion. Rheological behavior revealed that a higher storage modulus, loss modulus and complex viscosity of PEO/PBAT/PN-DOPO/Sep@AlPO4 composites could also promote the cross-linking structure during burning. Furthermore, the PEO/PBAT/PN-DOPO/Sep@AlPO4 composites exhibited excellent mechanical properties in terms of elongation at break and flexural performance than the PEO/PBAT system. All the results demonstrated that PEO/PBAT system modified by the combination of PN-DOPO and Sep@AlPO4 not only exhibited excellent synergistic effect on the flame retardance, but also had good improvement on thermal stability and mechanical properties, indicating the potential application in areas requiring fire safety.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Cisplatin is a widely used anticancer drug for treating solid tumors, but it is associated with severe side effects, including nephrotoxicity. Various studies have suggested that the nephrotoxicity of cisplatin could be overcome; nonetheless, an effective adjuvant drug has not yet been established. Oleanolic acid acetate (OAA), a triterpenoid isolated from Vigna angularis, is commonly used to treat inflammatory and allergic diseases. This study aimed to investigate the protective effects of OAA against cisplatin-induced apoptosis and necroptosis using TCMK-1 cells and a mouse model. In cisplatin-treated TCMK-1 cells, OAA treatment significantly reduced Bax and cleaved-caspase3 expression, whereas increased Bcl-2 expression. Moreover, in cisplatin-induced kidney injury mouse model, OAA treatment alleviated weight loss in the body and major organs and also relieved cisplatin-induced nephrotoxicity symptoms. RNA sequencing analysis of kidney tissues identified lipocalin-2 as the most upregulated gene by cisplatin. Additionally, necroptosis-related genes such as receptor interacting protein kinase (RIPK) and mixed lineage kinase domain like (MLKL) were identified. In vitro study, the phosphorylation of RIPKs and MLKL was reduced by OAA pretreatment in both cisplatin-treated cells and cells boosted by co-treatment with z-VAD-FMK. In conclusion, OAA could protect the kidney from cisplatin-induced nephrotoxicity and may serve as an anticancer adjuvant.

Primary biliary cholangitis (PBC) is a cholestatic liver disease characterized by immune-mediated injury to small bile ducts. Although PBC is an autoimmune disease, the results of traditional immunosuppressive therapy are disappointing. Nearly 40% of PBC patients do not respond to the first-line drug UDCA. Without appropriate intervention, PBC patients would eventually progress to liver cirrhosis and even death. There is an urgent need to develop new therapies. The gut-liver axis emphasizes the interconnection between the gut and the liver, and there is increasing evidence that gut microbiota and bile acids play an important role in cholestatic diseases. Dysbiosis of gut microbiota, imbalance of bile acids, and immune-mediated bile duct injury constitute the triad of pathophysiology in PBC. Understanding the gut microbiota-bile acid network and corresponding immune functions in PBC provides a new perspective for its treatment strategies. Therefore, we summarize the latest advancements in research of gut microbiota and bile acids in PBC and, for the first time, explore the potential of immune factors related to them as novel immunotherapy targets. This article discusses potential therapeutic approaches focusing on regulating gut microbiota, maintaining bile acid homeostasis, their interactions, and related immune factors.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

In agriculture, soil-borne fungal pathogens, especially Fusarium oxysporum strains, are posing a serious threat to efforts to achieve global food security. In the search for safer agrochemicals, silica nanoparticles (SiO2NPs) have recently been proposed as a new tool to alleviate pathogen damage including Fusarium wilt. Hollow mesoporous silica nanoparticles (HMSNs), a unique class of SiO2NPs, have been widely accepted as a desired pesticide carrier. However, their role in enhancing the disease resistance and the specific mechanism remain unknown. In this study, three sizes of HMSNs (19, 96 and 406 nm as HMSNs–19, HMSNs–96 and HMSNs–406, respectively) were synthesized and characterized to determine their effects on seed germination, seedling growth, and Fusarium oxysporum f. sp. phaseolus (FOP) suppression in cowpea roots by foliar spray using phenotypes, fresh biomass and disease progression as indicators. The results revealed that three HMSNs exhibited no adverse impacts on seed germination and tended to improve plant growth. Also, they exert their FOP suppression with a size- and concentration-dependent manner. HMSNs–406 possessed the best control effect at a concentration of 1000 mg/L showing an upto 40.00% decline in the disease severity. The Si(OH)4 control was also effective on FOP suppression at a lower concentration of 100 mg/L, whereas its higher concentrations exhibited obviously adverse impacts on FOP control, seed germination and plant growth. Moreover, we conformed that HMSNs posed their Fusarium wilt suppression in cowpea plant by activating SA (salicylic acid)-dependent SAR (systemic acquired resistance) responses rather than directly suppressing FOP. A higher level of SA content and elevated expression of its maker genes of PR-1 and PR-5 in HMSNs–406 treated cowpea roots provided substantial evidences of this mode of action. Other resistance-related genes, as well as defense-responsive enzymes, were also involved in the HMSNs-activated SAR pathway. Overall, for the first time, our results extended a new role of HMSNs as a potent elicitor to serve as a versatile alternative for plant disease protection of low cost, highly efficiency and sustainability.

Recently, the popularity of fermented foods has increased significantly. Lactofermented vegetable juice products are particularly important for our diet. The combination of the richness of the ingredients derived from vegetable juices and the products formed during lactic fermentation is a valuable source of nutrients. This study aimed to analyse the selected properties of fermented beetroot, carrot, and beetroot-carrot juices. The juices obtained from beetroot and carrot were fermented with bacterial strains Lactiplantibacillus plantarum or Levilactobacillus brevis. Density, extract, dry matter content, pH, total acidity, pigments (betalain or carotenoids), color, and LAB count were measured in the samples. The results obtained in this study showed that the used LAB strains were capable of fermenting the analyzed juices. It was proven that Lactiplantibacillus plantarum was a better strain for fermentation ion of vegetable juice. This might have been influenced by the fermentation temperature and the duration of the fermentation. However, this strain had a lower effect on carotenoids, which are water-insoluble pigments, than Lactiplantibacillus plantarum. The opposite observation was made for betalain, a water-soluble pigment with nitrogen in its structure.

A series of polycaprolactones (PCLs) with molecular weights of 950–10,100 g mol−1 and Ð of 1.10–1.87 have been synthesized via one-pot, solvent-free ring-opening polymerization (ROP) of ε-caprolactone (CL) using a heterogeneous double metal cyanide (DMC) catalyst. Various initiators such as polypropylene glycol, ethylene glycol, propylene glycol, glycerol, and sorbitol are employed to tune the number of hydroxyl end groups and properties of the resultant PCLs. Kinetic studies indicate that the DMC-catalyzed ROP of CL proceeds via a coordination mechanism. Branched PCLs copolymers are also synthesized via the DMC-catalyzed copolymerization of CL with glycidol. The α,ω-hydroxyl functionalized PCLs were successfully used as telechelic polymers to produce thermoplastic poly(ester-ester) and poly(ester-urethane) elastomers with well-balanced stress and strain properties.

This study investigated the effects of exogenous gibberellic acid (GA) treatments (elongating cluster + seedless + expanding, T1; seedless + expanding, T2; expanding, T3 and water, CK) on the content of sugars, organic acids, and endogenous hormones and sink strength.Results showed that T2 treatment displayed the highest fructose and glucose levels at 100 days after treatment (DAT), whereas its effect on tartaric acid, malic acid, and citric acid concentrations at 80 and 100 DAT was relatively weak. Under GA3 treatments, both GA3, IAA, and CTK contents increased, whereas ABA contents decreased at 1, 2, 4, 8, and 48 h. Analysis of sugar phloem unloading revealed that T2 treatment exhibited the highest values during softening and ripening stages. Our findings indicate that appropriate GA3 application can positively influence sink strength by regulating sink size and activity, including berry size enlargement, sugar phloem unloading and sugar accumulation in grape sink cells.

Organic compounds that contain poly-triazole are very important intermediates in pharmaceutical and chemical industry. Click chemistry is one of essential reactions that can form C-N bond with high atom economy. The research progress in metals catalyzed Click chemistry of azides and alkynes from the perspective of reaction mechanism is categorized and summarized.

This study presented a novel and sustainable method for producing chitin nanocrystals (PA-ChNCs) using phosphoric acid hydrolysis. The produced PA-ChNCs were used as stabilizers for Pickering emulsions and their physicochemical properties as well as stabilization mechanisms were systematically investigated. The PA-ChNCs exhibited small particle sizes and high surface areas, enabling an effective adsorption at the oil/water interface, which prevented coalescence in Pickering emulsions. The particle size and surface charge PA-ChNCs were strongly pH-dependent, which were critical factors for stabilizing Pickering emulsions. The study showed that emulsions with higher O:W ratios (50%) exhibited larger droplets but greater viscosity, forming a stable gel-like matrix that was more stable than emulsions with other O:W ratios after storage for 30 days. Emulsions with higher PA-ChNCs concentrations (2.0 wt%) and higher pH values (pH 10) showed small droplets and high viscosity, leading to stable emulsions. This research contributes to the development of sustainable and effective emulsifiers for use in the food industry, making utilization of seafood waste in an eco-friendly manner possible. Overall, this study highlights the potential of using newly developed PA-ChNCs as stabilizers for Pickering emulsions in food products.

A new process is reported for the incorporation of a fluoropolymer into a solid perovskite film. Poly(trifluoroethyl methacrylate) [CH2C(CH3)(CO2CH2CF3)]n was delivered to methylammonium lead iodide (CH3NH3PbI3) perovskite films by crystallizing the film in supercritical carbon dioxide/ethanol containing the dissolved fluoropolymer. The surface was characterized before and after fluoropolymer exposure using scanning electron microscopy, Raman spectroscopy and contact angle measurements. The results indicate that the fluoropolymer was incorporated into the perovskite film during the supercritical fluid crystallization process.

Owing to the growing concerns due to dwindling fossil fuel reserves, increasing energy demand and climate emergency, it is imperative to develop and deploy sustainable energy technologies to ensure future energy supply as well as transition to the net zero world. In this context, there is great potential in the biorefinery concept for supplying drop in biofuels in the form of biodiesel. Biodiesel as a fuel can certainly bridge the gap where electrification or the use of hydrogen is not feasible, for instance heavy vehicles, farm and marine transportation sector. However, biodiesel industry also leads to formation of large amount of crude glycerol as the byproduct. Crude glycerol due to presence of several impurities may not be a suitable feedstock for all high value products derived from glycerol but fits well with glycerol esterification for producing glycerol acetins, which have numerous applications. This review critically looks at the processes using nanostructured solid/liquid acid catalysts for glycerol esterification including the economic viability of the scale up.

Insufficient oral ridge tissue presents a challenge in the treatment of dental implants. One method to enhance alveolar crest dimensions is guided bone regeneration (GBR); however, existing membranes have certain limitations. To address this issue, we aimed to compare the effectiveness of a resorbable bilayer membrane composed of poly(l-lactic acid) and poly(-caprolactone) （PLACL）with that of a collagen membrane（COL） in a rat GBR model. The rat calvaria was used as an experimental model by placing a plastic cylinder. Forty male Fisher rats underwent surgery, and micro-computed tomography and histomorphometric analyses were performed to assess bone regeneration. The results showed that bone regeneration was similar across all the groups. However, after 24 weeks, the PLACL membrane demonstrated significant resilience, occasional partial degradation, and intermittent air bubble formation. This extended preservation of the barrier effect has great potential to facilitate optimal bone regeneration. In conclusion, this study shows that the PLACL membrane is a promising alternative to GBR. By providing a durable barrier and supporting bone regeneration over an extended period, this resorbable bilayer membrane may address the limitations of the current membranes. Further studies and clinical trials are warranted to validate the efficacy and safety of this drug in humans.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

Fluorophores with a tetraphenylethylene (TPE) core are attracting increasing interest because of their aggregation-induced emission (AIE) behaviour, which makes them particularly suitable when dispersed in thin-layer films. We propose the synthesis and use of a novel TPE fluorophore (hereafter called TPE-BPAN) decorated with two dimethylamino push groups and a 4-biphenylacetonitrile pull moiety. In tetrahydrofuran solutions, TPE-BPAN showed a broad absorption spectrum, and an intense emission is observed when a non-solvent as water is added in amounts of 70% and above. We selected and synthetized five different polymer matrices for TPE-BPAN with decreasing polarity: a) poly(methylmetacrylate) homopolymer (PMMA); b), c), and d) three copolymers of methyl methacrylate and cyclohexyl methacrylate at different compositions (P(MMA-co-CHMA) 75:25, 50:50, 25:75 mol%); e) poly(cyclohexyl methacrylate) homopolymer (PCHMA). The presence of a less polar comonomer as cyclohexyl methacrylate appeared to enhance the emission behaviour of TPE-BPAN, which displayed the highest quantum yield (QY) in P(MMA-co-CHMA) 75:25 in all the range of concentration studied from 0.4 wt.% to 2.0 wt.%. Further reduction in polarity lowered QY to the values of PMMA films; also, lower adhesion to the glass and a marked fragility of the films were observed. Referring to the P(MMA-co-CHMA) 75:25 films, QY values decreased from over 40% at 0.4 wt.% to about 30% at 2.0 wt.%, which is still helpful for energy harvesting applications such as luminescent solar concentrators (LSC). LSC performances were not significantly affected by the matrix's lower polarity and resulted in around one-third of the state-of-the-art due to the lower QY of TPE-BPAN. The theoretical investigation on density functional theory (DFT) clarified the origin of the observed AIE and the role played by the environment in modulating the photophysical behaviour.

Curcumin attracts a huge attention because of its biological properties: antiproliferative, antioxidant, anti-inflammatory, immunomodulatory and so on. However, its usage has been limited by poor water solubility and low bioavailability. Herein, to solve these problems we developed curcumin-loaded nanoparticles based on end-capped amphiphilic poly(N-vinylpyrrolidone). Nanoparticles were obtained using the suspension method and were characterized by dynamic and electrophoretic light scattering, transmission electron microscopy and atomic force microscopy. The average particle size was 200 nm, and ζ-potential was -4 mV. Curcumin release studies showed that nanoparticles are stable in water solution. In vitro release study showed prolonged action in gastric, intestinal and colonic fluids, consistently and in PBS. In vitro studies on epidermoid carcinoma and human embryonic kidney cells showed that the cells absorbed more curcumin in nanoparticles compared to pure curcumin. Nanoparticles are safe for healthy cells and show high cytotoxicity for glioblastoma cells in cytotoxicity studies in vitro. Median lethal dose was determined in acute toxicity assay on Zebrafish and was 23 μM. Overall, the curcumin-loaded nanoparticles seem promising for cancer treatment.

Wheat is widely grown in the Mediterranean region, where plants frequently face water shortages. Recently, more attention to rationalizing irrigation water has been increased due to the adoption of sustainable agricultural systems. Therefore, two field trials were conducted at the Agriculture Research Station of Nubaria, Egypt, in two consecutive seasons (2017/2018 and 2018/2019) to examine three irrigation regimes' effects, i.e., 60, 80, and 100% of crop evapotranspiration (ETc) combined with foliar ascorbic acid (AsA) or vitamin B2 (VB2) on yield and water productivity of wheat in two separate experiments. A split-plot design was used with three replicates. Irrigation treatments occupied the main plots, while the subplot in the first experiment was placed by ascorbic acid (AsA) and vitamin B2 in the second experiment. Results indicated that 100% ETc produced higher wheat yield and its attributes and insignificantly surpassed 80% ETc. Compared to the unsprayed plots, the foliar application of 6 mM ascorbic acid or 2.0 mM vitamin B2 significantly increased grain yield, components, and water use efficiency. The interaction between irrigation regimes (100% ETc or 80% ETc) and foliar application of 6.0 mM ascorbic acid or 2.0 mM vitamin B2 resulted in the highest values with no significant difference. Foliar application of ascorbic acid or vitamin B2 saved 20% of irrigation water while yielding a reduction that did not exceed 10%. The biplot graph of treatments x traits (TT) was a useful statistical tool for examining the impact of treatments on yield and its characteristics and identifying the links between these factors. Results suggest that riboflavin or ascorbic acid may have a potential role as an effective antioxidant for enhancing the tolerance for drought stress in wheat.

Due to the growing interest in biopolymers, biosynthesizable and biodegradable polymers currently occupy a special place. Unfortunately, the properties of native biopolymers are not satisfactory, which explain that attempts are being made to modify them. The work attempts to improve the properties of poly(3-hydroxybutyrate) (P3HB) using linear aliphatic polyurethane (PU) based on 1,4-butanediol and hexamethylene 1,6-diisocyanate. The conducted studies on the effect of the amount of PU used (5, 10, 15 and 20 wt.%) showed an improvement in the thermal properties of the prepared polymer blends. There was an increase in the degradation temperature of the ob-tained blends in relation to the native P3HB by 12-57C, and the difference between the melting point and the degradation point was above 100°C for most of the obtained blends. As part of the tested mechanical properties of the new polymer blends, we noted the desired increase in the tensile strength, in the relative elongation at break and in the impact strength with a decrease in hardness, in particular with the presence of 5 wt.% PU. Therefore, for further improvement, hybrid nanobiocomposites with 5 wt.% PU and organically modified montmorillonite (MMT – Cloisite 30B) were produced. The nanoadditive was used in typical amount of 1-3 wt.%. The nanostructure of the biocomposites produced by extrusion was examined by small-angle X-ray scattering (SAXS) and transmission electron microscopy (TEM), the morphology by scanning electron microscopy (SEM), and compatibility by infrared spectroscopy (FT IR). In addition, selected mechanical properties were determined and thermal properties were tested by the thermogravimetric analysis (TGA) and the standard differential scanning calorimetry (DSC). The polyester and polyurethane chains penetrated into the interlayer spaces of organically modi-fied nanoclay – Cloisite30B and the complete delamination occurred during direct mixing in the extrusion process. FT IR spectral analysis showed the compatibility of the polymer biocomposite components by the coexistence of intermolecular interactions in the form of hydrogen bonds. The morphology studies of the produced hybrid nanobiocomposites showed an interaction of the bi-opolymer matrix with PU and Cloisite30B and the formation of easily migrating polyester-polyurethane-montmorillonite adducts, which resulted in improved mechanical properties com-pared to the properties of the native P3HB and P3HB-PU compositions. The influence of the presence of a nanofiller on the properties of the prepared nanobiocomposites was tested and it was found that, as expected, the smallest amount of nanofiller provides the best results.It was found that the obtained nanobiocomposites containing the smallest amount of nano-fillers, i.e. 1 wt.% Cloisite30B exhibited the best mechanical and thermal properties. The desired decrease in hardness by 15% and a higher value of impact strength by 15%, an increase in elonga-tion at break by 60% and an increase in thermal stability of the newly produced biocomposites compared to to the native P3HB were observed. The prepared nanobiocomposites combined the best features caused by the elasticizing effect of polyurethane and the formation of P3HB-PU-MMT adducts.

Here, we present a series of novel block copolymers (BCP) from bio-derived monomers, poly(lactic acid)-block-poly(2,5-furandimethylene succinate) (PLA-b-PFS), in which the furan groups from PFS block can be crosslinked with bis(maleimido) triethylene glycol (M2) through a Diels-Alder reaction. This dynamic crosslinking reaction leads to a network structure for enhancing the mechanical properties compared to their linear BCP analogous. Decreasing the crosslinking density leads to a decrease of glass transition temperature of BCPs and a transition from glassy to rubbery-like behavior at room temperature. This allows a wide tunablity of both elastic moduli and yields of the materials. For the lowest crosslinking density. the material exhibits an over 50% self-healing efficiency at room temperature after five days, attributed to the low Tg (15.2 C) from the introduction of PFS block, allowing sufficient chain mobility for structure re-organization. Moreover, with the appropriate selection of crosslinking density (PLA-b-PFS/M2 (6/1)), it also shows an excellent shape memory property with a high recovery rate of 96.3% and a fixity rate of 97.3%. The permanent shape can be rewriteable due to the reversibility of Diels-Alder reaction. With these advanced functionalities and ease in large-scale fabrication, the PLA-b-PFS/M2 shows great promises for self-healing coatings or films with shape memory properties in a wide variety of applications such as packaging materials

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

Oral bone defects occur as a result of trauma, cancer, infections, periodontal diseases, and caries. Autogenic and allogenic grafts are the gold standard used to treat and regenerate damaged or defective bone segments. However, these materials do not possess the antimicrobial properties necessary to inhibit the invasion of the numerous deleterious pathogens present in the oral microbiota. In the present study poly(ε-caprolactone) (PCL), nano-hydroxyapatite (nHAp), and a commercial extract of Humulus lupulus L. (hops) were electrospun into polymeric matrices to assess their po-tential for drug delivery and bone regeneration. The fabricated matrices were analyzed by scanning electron microscopy (SEM), tensile analysis, thermogravimetric analysis (TGA), FT-IR assay, and in vitro hydrolytic degradation. The antimi-crobial properties were evaluated against the oral pathogens Streptococcus mutans, Porphyromonas gingivalis, and Aggregatibacter actinomycetemcomitans. The cytocompatibility was proved by the MTT assay. SEM analysis proved the nanostructured matrices have suitable fiber size. The present research provides new information about the interaction of natural compounds with ceramic and polymeric biomaterials. The hop extract and other natural or synthetic medicinal agents can be effectively loaded into PCL fibers and has the potential to be used in biomedical applications.

Poly(dA:dT) tracts cause nucleosome depletion in many species, e.g., at promoters and replication origins. Their intrinsic biophysical sequence properties make them stiff and unfavorable for nucleosome assembly, as probed by in vitro nucleosome reconstitution. The mere correlation between nucleosome depletion over poly(dA:dT) tracts in vitro and in vivo inspired an intrinsic nucleosome exclusion mechanism in vivo. However, we compile here published and new evidence that this correlation does not reflect mechanistic causation. 1) Nucleosome depletion over poly(dA:dT) in vivo is not universal, e.g., very weak in S. pombe. 2) The energy penalty for incorporating poly(dA:dT) tracts into nucleosomes is modest (<10%) relative to ATP hydrolysis energy abundantly invested by chromatin remodelers. 3) Nucleosome depletion over poly(dA:dT) is much stronger in vivo than in vitro if monitored without MNase and 4) actively maintained in vivo. 5) S. cerevisiae promoters evolved a biased poly(dA) versus poly(dT) distribution. 6) Nucleosome depletion over poly(dA) is directional in vivo. 7) The ATP dependent chromatin remodeler RSC preferentially and directionally displaces nucleosomes towards 5’ of poly(dA). Especially bias and directionality would not be expected for an intrinsic mechanism. Together, this argues for a mechanism where active and species-specific read out of intrinsic sequence properties, e.g., by remodelers, shapes nucleosome occupancy.

The Bacillus megaterium LVN01 species native to Colombia has demonstrated the ability to metabolize different co-products or industrial waste (such as fique juice, cane molasses, residual glycerol) and accumulate polyhydroxybutyrate (PHB), giving it potential in the bioplastics industry. In this research, the potential of liquid digestate as a carbon source for the production of PHA in fermentation processes with this bacterial strain was evaluated. Favorably, it was found that B. megaterium utilizes the nutrients from this residual substrate to multiply appropriately and efficiently synthesize poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV). Bench scale aerobic batch fermentation, under the operational conditions of this research [Volume: 3L; Temperature: 30.8°C; Agitation: 400 rpm; pH: 7.0 ± 0.2; Disolved Oxygen: 100% saturation; Antifoam 10% (v/v)], generated maximum values of DCW (0.56 g cell L-1) at 60 h, while the maximum PHB yield (360 mg PHB L-1) occurred at 16 h, which is very favorable for sustainable degradable bioplastics production. Additionally, GC-MS and NMR analyses confirmed that the PHBV copolymer synthesized by B. megaterium is made up of the monomers 3-hydroxybutyrate (3HB) and 3-hydroxyvalerate (3HV). Furthermore, the thermal properties determined by TGA (Tonset=283.1 ºC, Tendset= 296.98 ºC. Td =290.114 °C) and DSC (Tm= ºC155.7 °C, ΔHf= 19.80 J g-1, Xcr = 18.17%), indicate that it is a thermally stable biopolymer with low percentages of crystallinity, providing flexibility that facilitates molding, adaptation, and application in various industrial sectors.

Motivation by the definition of the type 2 poly-Bernoulli polynomials introduced by Kim-Kim [9], in the present paper, we consider a new class of new generating function for the Fubini polynomials, called the type 2 poly-Fubini polynomials by means of the polyexponential function. Then, we derive some useful relations and properties. We show that the type 2 poly-Fubini polynomials equal a linear combination of the classical of the Fubini polynomials and Stirling numbers of the first kind. In a special case, we give a relation between the type 2 poly-Fubini polynomials and Bernoulli polynomials of order r. Moreover, inspired by the definition of the unipoly-Bernoulli polynomials introduced by Kim-Kim [9]. We introduce the type 2 unipoly-Fubini polynomials by means of unipoly function and give multifarious properties including derivative and integral properties. Furthermore, we provide a correlation between the unipoly-Fubini polynomials and the classical Fubini polynomials.

Limonene epoxide (1,2 limonene oxide) readily reacts with carbon dioxide in a ring opening copolymerization reaction with insertion of CO₂ and formation of polycarbonates of exceptional chemical and physical properties. Both poly(limonene carbonate) and poly(limonene dicarbonate) can be synthesized using low cost Zn or Al homogeneous catalysts. This study addresses selected relevant questions concerning the technical and economic feasibility of limonene and carbon dioxide polymers en route to the bioeconomy.

Mitochondrial encephalomyopathy, lactic acidosis, and stroke-like episodes (MELAS) syndrome is one of the most frequent maternally inherited mitochondrial disorders.MELAS syndrome is a multi-organ disease that presents with a wide range of symptoms, such as dementia, epilepsy, lactic acidemia, myopathy, hearing loss, stroke-like episodes, diabetes, short stature, and myopathy. MELAS primarily affects tissue with high energy demands such as the brain, muscles, and heart. With 65–76% of affected people presenting at or before the age of 20, childhood is the typical age of onset. Genetic testing, imaging tests such as magnetic resonance imaging (MRI) scans, and other techniques, tests of blood, urine, and cerebrospinal fluid in addition to muscle biopsy (if necessary) may be used to diagnose MELAS syndrome. Management of MELAS remains largely supportive, focusing on symptom alleviation and metabolic stabilization. The long-term prognosis of MELAS is variable, influenced by factors such as age of onset, severity of symptoms, and presence of comorbidities. While some patients experience a relatively stable course with intermittent exacerbations, others may exhibit progressive neurological deterioration and multiorgan involvement. Early recognition, prompt intervention, and close monitoring are essential for optimizing outcomes and mitigating complications.Presenting here a case report of an occurrence of MELAS in a 31-year old male patient with chief complaints of perspiration, uneasiness and weight loss with increase in appetite and past history of bilateral hearing loss and vision loss in left eye.

Polymer-based piezoelectric biomaterials have already proven their relevance for tissue engineering applications. Further, the morphology of the scaffolds plays also an important role in cell proliferation and differentiation. The present work reports on poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV), a biocompatible, biodegradable and piezoelectric biopolymer that has been processed in different morphologies, including films, fibres, microspheres and 3D scaffolds. Further, the corresponding magnetically active PHBV-based composites were also produced. The effect of the morphology on physico-chemical, thermal, magnetic and mechanical properties of pristine and composites samples was evaluated, as well as their cytotoxicity. It was observed that the morphology does not strongly affect the properties of the pristine samples but the introduction of cobalt ferrites induces changes in the degree of crystallinity that could affect the applicability of prepared biomaterials. Young modulus is dependent of the morphology and also increases with the addition of cobalt ferrites. Both, pristine and PHBV/cobalt ferrite composite samples are no cytotoxic, indicating their suitability for tissue engineering applications.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

.Functionalization of multi-walled carbon nanotubes (MWNTs) surface with sulfonated poly(ether ether ketone) SPEEK chains using hexane diamine (HAD) as the interlinking molecule was investigated. MWNTs were first oxidized by nitric acid to generate carboxyl groups on their surface. Grafting of SPEEK chains on the MWNTs surface was achieved using hexane diamine as a cross-linking molecule. The attachment took place after the reaction of amine groups with carboxyl groups of oxidized MWNTs and sulfonate groups of SPEEK as confirmed by infrared (FTIR) analysis. Scanning electron microscopy (SEM) showed that MWNTs were packed into a dense and compact structure. Transmission electron microscopy (TEM) showed that the nanotubes were wrapped by polymer chains and arranged in a bundle like structure. These observations reveal that some of MWNTs were interconnected by SPEEK chains.

Nanomaterials such as pH-responsive polymers are promising for targeted drug delivery systems, due to the difference in pH between tumor and healthy regions. However, there is a significant concern about the application of these materials in this field due to their low mechanical resistance, which can be mitigated by combining these polymers with mechanically resistant inorganic materials such as mesoporous silica nanoparticles (MSN) and hydroxyapatite (HA). Mesoporous silica has interesting properties such as high surface area and hydroxyapatite has been widely studied to aid in bone regeneration, providing special properties adding multifunctionality to the system. Furthermore, fields of medicine involving luminescent elements such as rare earth are an interesting option in cancer treatment. The present work aims to obtain a pH-sensitive hybrid system based on silica and hydroxyapatite with photoluminescent and magnetic properties. The nanocomposites were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), nitrogen adsorption methods, CHN elemental analysis, Zeta Potential, scanning electron microscopy (SEM), and transmission electron microscopy (TEM), vibrational sample magnetometry (VSM), and photoluminescence analysis. Incorporation and release studies of the antitumor drug doxorubicin were performed to evaluate the potential use of these systems in targeted drug delivery. The results showed the luminescent and magnetic properties of the materials and showed suitable characteristics for application in the release of pH-sensitive drugs.

Hyperlipidemia is an identified risk factor for metabolic syndrome, obesity and cardiovascular complications characterized by elevated levels of lipids in blood. The present study aimed to inhibit HMG-CoA reductase with 15-oxoursolic acid through in-vivo and in-silico assessments. HFD-induced hyperlipidemia in rats was developed with a marked increase in total cholesterol (58.34 ± 0.21 mg/dl), triglycerides (45.45 ± 0.39 mg/dl), LDL-c (66.12 ± 0.10 mg/dl), VLDL-c (19.34 ± 0.16 mg/dl), and a decrease in HDL-c (10.34 ± 0.18 mg/dl). The oral administration of 15-oxoursolic acid at a concentration of 30 mg/Kg b.w significantly reduced the serum concentration of total cholesterol (42.65 ± 0.54 mg/dl), triglycerides (32.33 ± 0.16 mg/dl), LDL-c (50.34 ± 0.15 mg/dl) and VLDL-c (13.15 ± 0.45 mg/dl) respectively and an increased in the serum HDL-c (18.56 ± 0.34 mg/dl). 15-oxo ursolic acid also caused a decrease in the coronary risk index and atherogenic risk index. In-silico studies of 15-oxoursolic acid with HMG-CoA reductase showed significant interaction capability with binding energy (-9.26805 Kcal/mol). It is concluded that 15-oxoursolic acid could significantly reduce the total cholesterol, triglycerides and LDL levels in HFD-induced hyperlipidemia rats which might lead to new medication with significant hypolipidemic potential.

Translation is spatiotemporally regulated and ER-associated mRNAs are generally in efficient translation. It is unclear whether the ER-associated mRNAs are deadenylated or degraded on the ER surface in situ or in the cytosol. Here, we showed that ER possessed active deadenylases, particularly the poly(A)-specific ribonuclease (PARN), in common cell lines and mouse tissues. Consistently, purified recombinant PARN exhibited a strong ability to insert into the Langmuir monolayer and liposome. ER-anchored PARN was found to be able to reshape the poly(A) length profile of the ER-associated RNAs by suppressing long poly(A) tails without significantly influencing the cytosolic RNAs. The shortening of long poly(A) tails did not affect global translation efficiency, suggesting that the non-specific action of PARN towards long poly(A) tails was beyond the scope of translation regulation on the ER surface. Transcriptome sequencing analysis indicated that the ER-anchored PARN trigged the degradation of a small subset of ER-enriched transcripts. The ER-anchored PARN modulated the translation of its targets by redistributing ribosomes to heavy polysomes, suggesting that PARN may play a role in dynamic ribosome reallocation. During DNA damage response, MK2 phosphorylated PARN-Ser557 to modulate PARN translocation from the ER to cytosol. By promoting the decay of ER-associated MDM2 transcripts with low ribosome occupancy, the ER-anchored PARN modulated DNA damage response and thereby cell viability. These findings revealed that a highly regulated communication between mRNA degradation rate and translation efficiency is present on the ER surface in situ and that PARN may contribute to this communication by modulating the dynamic ribosome reallocation between transcripts with low and high ribosome occupancies.