The aim of this study was to determine the correlation between the external friction angle of cereal kernels and the roughness of a steel friction plate. The experiment was performed on the kernels of five principal cereals: wheat, rye, barley, oats and triticale. Flat seed units composed of three spaced kernels joined by adhesive tape were analyzed in each experimental variant. The external friction angle of flat seed units was determined on 9 steel friction plates with different roughness. Measurements were performed in 3 replications with a photosensor device which registered the external friction angle of cereal kernels. On friction plates with surface roughness Ra=0.36 to Ra=6.72, the average values of the angle of external friction ranged from 17.56° in rye kernels to 34.01° in oat kernels. The greatest similarities in the angle of external friction were observed between wheat and triticale kernels, whereas the greatest differences were noted between barley and oat kernels and between barley and triticale kernels. Friction plates made of ST3S steel should be characterized by the lowest surface roughness to minimize energy consumption during grain processing. The optimal surface roughness of steel friction plates was determined at Ra=0.9.

The paper discusses how joint damage and deterioration affect the seismic response of existing reinforced concrete frames with sub-standard beam-column joints. The available simplified modeling techniques are critically reviewed to propose a robust, yet computationally efficient technique for simulating the nonlinear behavior of substandard beam-column joints. Improvements over the existing models include simulation of the cyclic deterioration of joint stiffness and strength as well as pinching in the hysteretic response, implemented considering a deteriorating hysteretic rule. A fibre-section forced-based inelastic beam-column element is developed; considering improved material models and fixed-end rotation due to bond failure, rebars-slip and inelastic extension, to simulate the deteriorating cyclic behavior of existing pre-cracked beam-column members. For the assessment of frames with substandard exterior beam-column joints, a nonlinear model for the exterior joint is developed and validated through a full-scale quasi-static cyclic test performed on a substandard T-joint connection. The proposed model allows considering structural performance in risk assessment while accounting for true inelastic mechanisms at the joints.

Purpose: The purpose of this study is to apply the Composite Radiographic Index modified (CRIm) in CBCT scans of patients with Medication related osteonecrosis of the jaws (MRONJ) in order to detect its validity, and corelate the radiologic findings with the clinical staging of the disease. Methods: This study included 43 patients with MRONJ diagnosis and CBCT scans performed in the School of Dentistry and approved by the Research Ethics Committee. Clinical staging for every patient (0-3) was provided according to AAOMS 2022 guidelines. In cases of patients with both jaws affected, each jaw was evaluated independently resulting to 52 CBCT scans. The 52 CBCT scans were assessed under standardized viewing conditions by 2 observers who evaluated independently the following 8 radiologic features: lytic changes, sclerosis, periosteal reaction, sequestration, non-healing extraction sockets and other findings (sinus implication, inferior alveolar canal involvement, jaw fracture). The CRIm index was constructed to assess the extent of osseous changes. The radiologic features were scored as absent (0), localized/single (1), extensive/multiple (2), yielding a theoretical range of 0–12. For statistical analysis Fisher’s exact test and Spearman’s correlation coefficient were performed. Results: A statistically significant association of clinical stage with lytic changes, sequestration and inferior alveolar canal involvement was found. Also, a statistically significant correlation of clinical stage with CRIm index classification was obtained. Conclusions: The CRIm index tends to increase as the clinical stages of MRONJ advance, suggesting a correlation between the clinical stage of MRONJ and the CRIm index.

The undoped and tungsten (W)-doped vanadium dioxide (VO₂) thin films were prepared by electron beam evaporation associated with ion-beam assisted deposition (IAD). The influence of different W-doped contents (3%-5%) on the optical, electrical, structural, and thermos-mechanical properties of VO₂ thin films was investigated experimentally. Spectral transmittance results showed that with the increase of W-doped contents, the transmittance in the visible light range (400-750 nm) decreases from 60.2% to 53.9%, and the transmittance in the infrared wavelength range (2.5 μm to 5.5 μm) drops from 55.8% to 15.4%. As the W-doped content increases, the residual stress in the VO₂ thin film decreases from -0.276 GPa to -0.238 GPa, but the surface roughness increases. For temperature-dependent spectroscopic measurements, heating the VO2 thin films from 30°C to 100°C showed the most significant change in transmittance for the 5% W-doped VO₂ thin film. When the heating temperature exceeds 55°C, the optical transmittance drops significantly, and the visible light transmittance drops by about 11%. Finally, X-ray Diffraction (XRD) and scanning electron microscope (SEM) were used to evaluate the microstructure characteristics of VO₂ thin films.

The study proposes a theoretical method for evaluating the 'safety against derailment' indicator of a specialized train composition for the transportation of very long rails. A composition of nine wagons, suitable for the transportation of rails with a length of 120 m, is considered. For the remaining recommended rail lengths, the number of wagons is reduced or increased, the method being modified depending on the required configuration. In accordance with the requirements of EN 14363:2019, the composition is in a curve with a radius of R=150 m. The rails bend, some of them contact the vertical stanchions of the wagon and cause additional transverse forces, which are balanced in the rail track. This is a prerequisite for derailment of the vehicle. The goal of the study is to determine the additional transverse forces that arise because of the bent rails. The task is statically indeterminate, and considering the dimensions of the rails, its solution becomes seriously difficult. For the purposes of the study, the finite element method was used. Based on the displacements of the support points of the rails (caused by the geometry of the curve) the bending line of the elastic load is determined and the forces in the supports are calculated. A group of five rails is considered, with results multiplied proportionally for cases other than five. The resulting forces are considered when determining the derailment safety criterion defined by EN 14363:2019.

The effects of co-addition CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases and wear property of plasma beam spraying Fe55-based coatings on 1025 steel were investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDS), ultra-deep field microscope and wet sand rubber wheel friction tester, respectively. The results showed that the dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of microstructure with the co-addition CeO2 and SiC particles. With addition of CeO2 or SiC affected the flowability of molten steel at macro level, leading to a reduction in the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of Fe55 welding layer is Cr7C3, γ-Fe. The grain boundaries consisted mainly of a reticular eutectic structure. The worn-out uniformly surface of the Fe55+1.5 wt% SiC+0.01wt% CeO2 with Ra was 0.28 μm was smoother than that of other samples. The sub-wear mechanisms during the friction process were microploughing and microcutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01wt% CeO2 were well-matched, avoiding excessive microcutting and microplastic deformation.

CBCT significantly impacts dental procedures and has brought significant reforms in our approach to diagnosis & treatment planning despite its limitations in differentiating soft tissues. It is an excellent imaging modality and quickly identifies sinus opacification and provides valuable in-sight into paranasal sinus pathologies with considerably lower radiation exposure. The present study aimed to investigate the occurrence of maxillary sinus abnormalities in CBCT scans, identify the frequency, type, and location of these findings, and find the correlation between the distance of periapical lesions and radiographic changes in the maxillary sinus. Two examiners independently evaluated 117 patients to diagnose and classify the cases into different abnormality subtypes. The periapical lesions most closely related to the sinus were recorded. The diameters of the left and right maxillary sinus ostium and the distance of the ostium's lower border to the sinus's osseous floor were recorded. The findings were correlated with the age and gender of these patients. The present study revealed that sixty-one patients were diagnosed with mucosal thickening (52.1%). The sinus wall most affected by mucosal thickening was the maxillary sinus floor, followed by the medial and lateral walls. Of 19 patients with periapical lesions, 15 had maxillary sinus mucosal thickening and was statistically significant (p=0.004). The high occurrence of abnormalities in the maxillary sinus emphasizes the importance for the radiologist to comprehensively interpret the whole volume acquired in CBCT images, including the entire sinus. Incidental findings may be considered in the individual clinical context of signs and symptoms, reducing the risk of overes-timating the real impact of radiographic findings.

: The paper presents the results of uniaxial tensile tests of samples of hypoeutectic aluminum-silicon alloy A319. According to the results of which the influence of surface treatment by a pulsed electron beam on the mechanical properties of the material was determined. The peculiarities of localization of deformation in the material, caused by grinding of the surface layer material structure due to rapid crystallization during electron beam treatment were revealed. The surface treatment up to 100 µm depth leads to the formation of a fine dendritic columnar structure of silumin and to an increase in the plasticity of the samples. The influence of surface treatment affects the increase of deformation localization in the region of stable concentrator before failure. The largest increase in ductility and localization of deformation occurs during processing with energy density of 15 J/cm2. In the process of specimen deformation, unstable, metastable, and stable areas of plastic deformation localization are formed and replaced, and the formation of stable areas of localized plastic deformation, in which the specimen fails at the end of the test, can be detected at the initial stages of testing. In specimens, during testing in the zone of localized plastic deformation, bands are formed that pass through the entire surface of the specimen at an angle from 35 to 55 degrees to the axis of tension, their evolution leads to the formation of stable zones of localized plastic deformation and to the failure of the specimen.

There is increasing interest in the application of near-infrared (NIR) laser light for the treatment of various musculoskeletal disorders. The present study thoroughly examined the physical characteristics of laser beams from two different laser therapy devices that are commercially available for the treatment of musculoskeletal disorders. Then, these laser beams were used to measure the penetration depth in various biological tissues from different animal species. The key result of the present study was the finding that for all investigated tissues, most of the initial light energy was lost in the first one to two millimeters, more than 90% of the light energy was absorbed within the first ten millimeters, and there was hardly any light energy left after 15 – 20 mm of tissue. Furthermore, the investigated laser therapy devices fundamentally differed in several laser beam parameters that can have an influence on how light is transmitted through tissue. Overall, the present study showed that a laser therapy device that is supposed to reach deep layers of tissue for treatments of musculoskeletal disorders should operate with a wavelength between 800 nm and 905 nm, a top-hat beam profile, and it should emit very short pulses with a large peak power.

Purpose: To report the early clinical outcomes of combining intensity‐modulated radiation therapy (IMRT) and intensity‐modulated proton therapy (IMPT) in comparison with IMRT alone in treating the oropharynx cancer (OPC) patients. Materials and Methods: The medical records of 148 OPC patients were retrospectively reviewed, who underwent definitive radiotherapy (RT) with concurrent systemic therapy, from January 2016 till December 2019 at Samsung Medical Center. During the 5.5 weeks’ RT course, the initial 16 (or 18) fractions were delivered by IMRT in all patients, and the subsequent 12 (or 10) fractions were either by IMRT in 81 patients (IMRT only) or by IMPT in 67 (IMRT/IMPT combination), respectively, based on comparison of adaptive re-plan profiles and availability of equipment. Propensity‐score matching (PSM) was done on 76 patients (38 from each group) for comparative analyses. Results: With the median follow‐up of 24.7 months, there was no significant difference in overall survival and progression free survival between groups, both before and after PSM. Before PSM, IMRT/IMPT combination group experienced grade ≥3 acute toxicities less frequently: mucositis in 37.0% and 13.4% (p<0.001); and analgesic quantification algorithm (AQA) in 37.0% and 19.4% (p=0.019), respectively. The same trends were observed after PSM: mucositis in 39.5% and 15.8% (p=0.021); and AQA in 47.4% and 21.1% (p=0.016), respectively. In multivariate logistic regression, grade ≥3 mucositis was significantly less frequent in IMRT/IMPT combination group, both before and after PSM (p=0.027 and 0.024, respectively). AQA score ≥3 was also less frequent in IMRT/IMPT combination group, both before and after PSM (p=0.085 and 0.018, respectively). Conclusions: In treating the OPC patients, with comparable early oncologic outcomes, more favorable acute toxicity profiles were achieved following IMRT/IMPT combination than IMRT alone.

Directional modulation (DM), as an emerging promising physical layer security (PLS) technique at the transmitter side with the help of an antenna array, has developed rapidly over decades. In this study, a DM technique using a polarization sensitive array (PSA) to produce the modulation with different polarization states (PSs) at different directions is investigated. A PSA, as a vector sensor, can be employed for more effective DM for an additional degree of freedom (DOF) provided in the polarization domain. The polarization information can be exploited to transmit different data streams simultaneously at the same directions, same frequency, but with different PSs in the desired directions to increase the channel capacity, and with random PSs off the desired directions to enhance PLS. The proposed method has the capability of concurrently projecting independent signals into different specified spatial directions while simultaneously distorting signal constellation in all other directions. The symbol error rate (SER), secrecy rate, and the robustness of the proposed DM scheme are analyzed. Design examples for single- and multi-beam DM systems are also presented. Simulations corroborate that 1) the proposed method is more effective for PLS; 2) the proposed DM scheme is more power-efficient than the traditional artificial noise aided DM schemes; and 3) the channel capacity is significantly improved compared with conventional scalar antenna arrays.

It is well-known that surface plasmon wave propagates along a straight line, but this common sense was broken by the artificial curved light – plasmon Airy beam. In this paper, we introduce a new class of curved surface plasmon wave - the photonic hook plasmon. It propagates along wavelength scaled curved trajectory with radius less than surface plasmon polariton wavelength, and can exist despite the strong energy dissipation at the metal surface.

In this paper, we study the well-posedness and asymptotic behaviour of solutions to a laminated beam in thermoelasticity of type III. We first give the well-posedness of the system by using the semigroup method. Then, we show that the system is exponentially stable under the assumption of equal wave speeds. Furthermore, it is proved that the system is lack of exponential stability for case of nonequal wave speeds. In this regard, a polynomial stability result is proved.

In this work, we consider a one-dimensional laminated beam in the case of non-equal wave speeds with only one infinite memory on the effective rotation angle. In this case, we establish the general decay result for the energy of solution without any kind of internal or boundary control. The main result is obtained by applying the method used in Guesmia et al. (Electron. J. Differential Equations 193: 1-45, 2012) and the second-order energy.

Background: The variability of the obtained results of manual tests assessing the angle of strabismus depends on the experience, skills, and training of the examiner. The authors hope that the new measuring device will provide a more sensitive and repeatable method for detecting small strabismus angles compared to the gold standard – PCT. The purpose of this article is to present an innovative strabismus angle demonstration device, called Strabiscan, to present automated measurements of eye deviation, and to compare the obtained results of these measurements to the traditional manual method. Methods: In patients with the manifest strabismic disease (n = 30) and a group of healthy subjects (n = 30), a detailed history was taken and routine ophthalmologic examinations were performed, including best-corrected distance visual acuity, assessment of refractive error using an autorefractometer after cycloplegia, biomicroscopic evaluation of the anterior segment of the eye, and evaluation of the eye fundus by indirect ophthalmoscopy. Subsequently, each patient and healthy subjects were subjected to a prismatic cover-uncover test using a manual method, and then the presence of strabismus was detected and its angle assessed using demonstration Strabiscan device. Results: In the control group, using the Strabiscan demonstration device, small-angle latent strabismus ≤3DP was diagnosed in 83% of patients, and >3DP in 13%. In contrast, using the prismatic cover-uncover test, latent strabismus ≤3DP was diagnosed in only 13% of patients, and latent strabismus with an angle >3DP in 13% of patients. No statistically significant differences were noted in the measurements of strabismus angles made by the different methods. Conclusions: The Strabiscan demonstration device allows quick and accurate assessment of the strabismus angle. Compared to the prismatic cover-uncover test, it has a higher sensitivity for detecting low-angle latent strabismus. Measurements with the Strabiscan do not require the presence of additional co-assistants for the test.

The LED light source is an important light source for indoor visible light communication. It has the characteristics of a large divergence angle and a high transmission rate. Therefore, using LED as the light source for visible light full-duplex communication can not only satisfy the lighting requirements but also transmit information at high speed. To analyze the factors that affect the optical power of the indoor single-light source visible light communication uplink receiving end, an indoor visible light communication model was established, and mathematical calculation formulas were derived based on the model establishment, and the maximum movable range formula of the retroreflective end under specific conditions was derived; The reliability of the formula was verified with the help of Zemax simulation software. Theoretical analysis and experimental results show that increasing the movement range of the retroreflective end can be achieved by increasing the lens diameter, reducing the focal length, and increasing the link distance.

The flow field around a delta wing is substantially altered by the impact of the active flow control technique. The present study involves the sharp-edged delta wing of 65 deg sweep angle with different active flow control configurations. The blowing was employed as an active flow control method on the top surface of the delta wing. The various configurations considered are the baseline delta wing, delta wing with blowing holes located at 1.62%, 3.24% and 4.86% of root chord from the leading edge to the centre of the blowing holes. The computation is performed using the commercial software ANSYS Fluent. Unsteady, incompressible Reynolds-averaged Navier-Stokes equation and the shear-stress transport k-ω turbulence model are employed. The angles of attack varied in the range of 0^o < α < 35^o and Reynolds number is 2.64 x10⁶ and the jet momentum coefficient is fixed at 0.05. The blowing of air from the injection region enhances the strength of the leading-edge vortices resulting in the delay of the vortex breakdown. The performance of the delta wing is greatly improved while using the blowing method specifically for the blowing holes located at 3.24% of root chord from the leading edge as compared to without the blowing method.

Despite their anti-icing ability, hydrophobic coatings have the disadvantages of easy falling off and poor wear resistance, resulting in insufficient durability of ice/snow melting. To improve the surface stability and durability of superhydrophobic coatings, nanoparticle/epoxy coatings were prepared with three types of nanoparticles, two types of dispersion methods, three types of application methods and two types of introduction methods of epoxy resin. Water contact angles, ice adhesion force and icing rate of asphalt concrete coated with hydrophobic coatings were tested. The molecular structures of coatings were analyzed by Fourier transform infrared spectroscopy. The surface morphology of hydrophobic coatings was observed using Scanning electron microscopy. Results indicated that nano-ZnO, TiO2 and SiO2 particles can be modified into hydrophobicity by stearic acid. The hydrophobic coating could improve the hydrophobicity of concrete, reduce the adhesion strength of ice and asphalt concrete and delay the beginning icing time. Moreover, The dosages of stearic acid, nanoparticle and epoxy resin need to be in a certain range to ensure the best hydrophobicity and durability of coatings.

This research focuses on exploring gravitational lensing of the wormhole in Einstein-bumblebee gravity with an antisymmetric tensor. The Gibbons and Werner technique based on the Gauss-Bonnet theorem is utilized to calculate the bending angle of light. The effects of non-plasma and plasma medium on the bending angles are investigated. Furthermore, we examine the deflection angle $\Tilde{\alpha}$ in relation to the impact parameter $\sigma$ and minimal radius $r_{0}$ in both non-plasma and plasma mediums. Our findings indicate that the deflection angle is positively correlated with $r_{0}$, meaning that larger values of $r_{0}$ result in larger deflection angles and smaller values of $r_{0}$ result in smaller deflection angles. On the other hand, the deflection angle $\Tilde{\alpha}$ is inversely related to the impact parameter $\sigma$.

We have recently introduced the possibility of performing operando small-angle X-ray scattering measurements using a novel industrially relevant injection moulding system for plastics. We show that useful time-resolving measurements can be performed with a time-cycle of 1s and we highlight the possible steps to reduce this to 0.5s. We show how we can use the transmission measurements to provide a time-marker when plastic first enters the mould cavity in the region probed by the incident X-ray beam. We show the opportunities provided by this experimental stage mounted on the NCD-SWEET beamline at ALBA to probe the reproducibility of the injection moulding system on different scales. The design of the equipment allows the development of the structure and the morphology to be evaluated in different parts of mould cavity and we evaluate any differences in a rectangular mould cavity. We identify future prospects for this equipment in terms of novel mould heating and cooling systems and the opportunities for quantitatively evaluating radical approaches to injection moulding technology.

As one of the common techniques for measuring coseismic deformations, optical image correlation techniques are capable of overcoming the drawbacks of inadequate coherence and phase blurring which can occur in radar interferometry, as well as the problem of low spatial resolution in radar pixel offset tracking. However, the scales of the correlation window in optical image correlation techniques typically influence the results, the conventional SAR POT method faces a fundamental trade-off between the accuracy of matching and the preservation of details in the matching window size. This study regards co-seismic deformation as a two-dimensional vector, and develops a new post-processing workflow called VACI-OIC to reduce the dependence of shift estimation on the size of the matching window. This paper takes the coseismic deformations in both the east-west and north-south directions into account at the same time, treating them as vectors, while also considering the similarity of displacement between adjacent points on the surface. Herein, the angular continuity index of the coseismic deformation vector was proposed as a more reasonable constraint condition to fuse the deformation field results obtained by optical image correlation across different matching window. Taking the earthquake of 2021 in Maduo, China, as the study area, the deformation with the highest spatial resolution in the violent surface rupture area was determined (which could not be provided by SAR data). Compared to the results of single-scale optical correlation, the presented results were more uniform (i.e., more consistent with published results). At the same time, the proposed index also detected the strip fracture zone of the earthquake with impressive clarity.

F-type ATP synthases play a key role in oxidative and photophosphorylation processes producing adenosine triphosphate (ATP) for most biochemical reactions in living organisms. In contrast to the mitochondrial FOF1-ATP synthases those of chloroplasts are known to be mostly monomers with approx. 15% fraction of oligomers interacting presumably non-specifically in a thylakoid membrane. To shed light to the nature of this difference we studied interactions of the chloroplast ATP synthases using small-angle X-ray scattering (SAXS) method. Here, we report evidence of I-shaped dimerization of solubilized FOF1-ATP synthases from spinach chloroplasts at different salinity. The structural data were obtained by SAXS and showed dimerization in response to changes in ionic strength. The best model describing SAXS data was two ATP-synthases connected through F1/F1’ parts, presumably via their δ-subunits, forming dimers with the “I” shape. Such I-shaped dimers might possibly connect the neighboring lamellae in thylakoid stacks assuming that the FOF1 monomers comprising such dimers are embedded in different thylakoid membranes. If this type of dimerization exists in nature, it might be one of the pathways of inhibition of chloroplast FOF1-ATP synthase for preventing of ATP hydrolysis in dark, when salinity in plant chloroplasts is rising. Together with a redox switch inserted into a γ-subunit of chloroplast FOF1 and lateral oligomerization, an I-shaped dimerization might comprise a subtle regulatory process of ATP synthesis and stabilize the structure of thylakoid stacks in chloroplasts.

This study introduces a new procedure for three-component spectral matching of seismic ground acceleration records. The procedure involves preserving the phase angle and varying the Fourier amplitudes to match the spectra of the recorded records with a provided target spectrum that represents the spectral values of ground motions in three orthogonal directions. Several three-component recorded records were matched against two target response spectra to test the method. An accurate convergence was achieved in the velocity and displacement records. In addition, the scales among the components’ magnitude were maintained, creating realistic three-component ground motions. Such ground motion inputs are important to qualify critical structures sensitive to three-component motions. Our proposed procedure is novel because the present practices are mostly created based on one-component ground motions.

A novel scheme that can simultaneously measure the Doppler frequency shift (DFS) and angle of arrival (AOA) of microwave signals is proposed. At the signal receiving unit (SRU), two echo signals and the reference signal are modulated by a Sagnac loop structure and sent to the central station (CS) for processing. At the CS, two low-frequency electrical signals are generated after polarization control and photoelectric conversion. The DFS without direction ambiguity and wide AOA measurement can be real-time acquired by monitoring the frequency and power of the two low-frequency electrical signals. In the simulation, an unambiguous DFS measurement with errors of ±3×10-3 Hz and a -90° to 90° AOA measurement range with errors of less than ±0.5° are realized. The safety and robustness of the system to environmental disturbance are improved, and it is more suitable for the modern electronic warfare system.

Increased definite power, reduced cost, and dynamic construction are the important features required by electric motors for various applications. One such motor accommodating all the requisites mentioned above is Switched reluctance. Applications pertaining to small, commercial, and EV find Switched reluctance machine as a developing competitor to the conventional induction and permanent magnet motors. Though SRMS contribute a considerable number of advantages over induction motors and permanent magnet motors, the primary disadvantages pertaining to SRMs are the torque ripple, especially at high-speed operation, and the resulting acoustic noise. These disadvantages may not always be detrimental to the systems in entirely all cases, but depending on the application to be employed, torque ripple and acoustic noise form are detrimental to the system. This paper reviews the technology status and recent trends in the minimization of torque ripples switched reluctance machines.

Advanced manufacturing techniques, aimed at implants with high dependability, flexibility, and low manufacturing costs, are crucial in meeting the growing demand for high-quality products like biomedical implants. Incremental sheet forming is a promising flexible manufacturing approach for rapidly prototyping sheet metal components using low-cost tools. Titanium and its alloys are used to shape most biomedical implants because of its superior mechanical qualities, biocompatibility, low weight, and great structural strength. The poor formability of titanium sheets at room temperature, however, limits their widespread use. The goal of this research is to show that gradual sheet formation of a titanium biomedical implant is possible. The possibility of creative and cost-effective concepts for the manufacturing of such complicated shapes with significant wall angles is explored in this study. A numerical simulation based on finite element modeling as well as a design process tailored to metal forming is used to complete the development. The mean of uniaxial tensile tests with a constant strain rate was used to study the flow behavior of the studied material. To forecast the crack, the obtained flow behavior was modeled using the behavior model and failure model.

Particle deposition on the surface of the drying chamber poses the main drawback in the spray drying process, which reduces the product recovery and affects the quality of the product. In view of this, the potential application of chemical surface modification to produce a hydrophobic surface that reduces the powder adhesion (biofouling) on the wall of the drying chamber was investigated in this study. The hydrophobic Polydimethylsiloxane (PDMS) solution was used in the vertical dipping method at room temperature to determine the optimum coating parameters on borosilicate glass and stainless-steel substrates, which were used to mimick the wall surface of the drying chamber, to achieve highly hydrophobic surfaces. A single-factor experiment was used to define the range of the PDMS concentration and treatment duration using the Response Surface Methodology (RSM). The Central Composite Rotatable Design (CCRD) was used to study the effects of the concentration of the PDMS solution (X1, %) and the treatment duration (X2, hr) on the contact angle of the substrate (°), which reflected the hydrophobicity of the surface. A three-dimensional (3D) response surface was constructed to examine the influence of the PDMS concentration and treatment duration on the contact angle readings, which serve as an indicator of the surface's hydrophobic characteristic. Based on the optimisation study, the PDMS coating for the borosilicate glass achieved an optimum contact angle of 99.33° through the combination PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 4.94 hr, while the PDMS coating for the stainless-steel substrate achieved an optimum contact angle of 98.31° with PDMS concentration: X1 = 1% (w/v) and treatment time X2 = 1 hr. Additionally, the infrared spectra identified several new peaks that appeared on the PDMS-treated surfaces, which represented the presence of Si-O-Si, Si-CH3, CH2, and CH3 functional groups for the substrates coated with PDMS. Furthermore, the surface morphology analysis using the Field Emission Scanning Electron Microscopy (FESEM) showed the presence of significant roughness and uniform nanostructure on the surface of PDMS-treated substrates, which indicated the reduction of wettability and the potential effect on unwanted biofouling on the spray drying chamber.

In this paper, we study the gravitational lensing by some black hole classes within the non-linear electrodynamics in weak field limits. First, we calculate an optical geometry of the non-linear electrodynamics black hole then we use the Gauss-Bonnet theorem for finding deflection angle in weak field limits. The effect of non-linear electrodynamics on the deflection angle in leading order terms is studied. Furthermore, we discuss the effects of the plasma medium on the weak deflection angle.

This work attempted to fabricate superhydrophobic fabric via simple immersion technique. Textile fabrics were coated with silica nanoparticles prepared from tetraethoxysilane (TEOS) to obtain sufficient roughness with hydrophobic surface chemistry. Then the coated fabrics were treated with polydimethylsiloxane (PDMS) and aminopropyltriethoxysilane (APTES) to reduce the surface energy. The effects of PDMS concentration on the surface morphology and superhydrophobicity of as-prepared fabric were investigated. The morphology and the composition of superhydrophobic fabric was characterized by scanning electron microscopy (SEM), energy dispersive X-ray (EDS) and Fourier transform infrared (FTIR) spectroscopy. The results revealed the formation of spherical silica nanoparticles with average particle size of 250 nm throughout the fabric surface. The possible interactions between silica nanoparticles and APTES, as well as the fabrics were elucidated. Investigating the hydrophobicity of fabrics via water contact angle (WCA) measurement showed that the treated fabric exhibits excellent water repellency with a water contact angle as high as 151° and a very low water sliding angle. It also found that the treated fabric maintained most of its hydrophobicity against repeated washing. The comfort properties of the obtained superhydrophobic fabrics in term of air permeability and bending length did not reveal any significant changes.

In this article, we demonstrate the weak gravitational lensing in the context of Bocharova-Bronnikove-Melnikov-Bekenstein (BBMB) black hole. To this desire, we derive the deflection angle of light in a plasma medium by BBMB black hole using the Gibbons and Werner method. First, we obtain the Gaussian optical curvature and implement the Gauss-Bonnet theorem to investigate the deflection angle for spherically symmetric spacetime of BBMB black hole. Moreover, we also analyze the graphical behavior of deflection angle by BBMB black hole in the presence of plasma medium.

Membranes based on sulfonated synditoactic polystyrene were thoroughly characterized by contrast variation SANS over a wide Q-range in dry and hydrated states. The film samples were prepared by solid-state sulfonation that allowed a uniform sulfonation of only the amorphous phase while preserving the crystallinity of the membrane. The samples were loaded with different guest molecules in either the amorphous (fullerenes) or the crystalline (toluene) regions, in order to vary the neutron contrast or to reproduce the conditions enabling an increased resistance of the membranes to chemical decomposition. The use of uni-axially deformed film samples and contrast variation with different H2O/D2O mixtures allowed for the identification and characterization of different structural levels with sizes between nm and μm, which form and evolve in the membrane morphology in dry and hydrated states and produce scattering features on different detection sectors and at different detection distances after the sample, depending on their size and orientation.

Traditional winglets are designed as fixed devices attached at the tips of the wings. The primary purpose of the winglets is to reduce the lift-induced drag, therefore improving aircraft performance and fuel efficiency. However, because winglets are fixed surfaces, they cannot be used to control lift-induced drag reductions or to obtain the largest lift-induced drag reductions at different flight conditions (take-off, climb, cruise, loitering, descent, approach, landing, and so on). In this work, we propose the use of variable cant angle winglets which could potentially allow aircraft to get the best all-around performance (in terms of lift-induced drag reduction), at different flight phases. By using computational fluid dynamics, we study the influence of the winglet cant angle and sweep angle on the performance of a benchmark wing at Mach numbers of 0.3 and 0.8395. The results obtained demonstrate that by adjusting the cant angle, the aerodynamic performance can be improved at different flight conditions.

Background A body composition monitor (BCM) has a role not only in determining over-hydration (OH) but also as an aid to nutritional assessment. For dialysis patient-specific clinical applications of BCM, it is necessary to clarify the relationship between body composition parameters and OH in healthy Chinese individuals. Methods This cross-sectional study involved 314 healthy individuals with a mean age of 45.7±13.1 years. BCM measurements were performed while the subjects were fasting. Results The mean OH level was 0.379±0.81 L. Lean tissue index (LTI) and Lean tissue mass (LTM) were significantly higher in males (p<0.001), while fat tissue index (FTI) was significantly higher in females (p<0.001). In univariate correlation analysis, FTI, Fat, and ATM had a negative correlation with OH in females and all subjects (p<0.05), while LTM and BCM had a positive correlation in all subjects (p<0.05). There was a significant negative correlation between phase angle (PhA) and OH in males, females, and all subjects (r=-0.634, p<0.001; r=-0.666, p<0.001; r=-0.484, p<0.001, respectively). In multivariate linear regression analysis, PhA (b=-1.266, p<0.001), LTM (b=0.987, p<0.001), age (b=-0.307, p<0.001) were independent predictors of OH. Conclusions This study demonstrated that age, LTM and especially PhA, had important roles in predicting OH in healthy Chinese individuals. In the future, PhA may aid in clinical assessment by helping to titrate dry weight among hemodialysis patients with malnutrition.

Energy dissipation is one of the most important factors in choosing stepped spillways. However, few studies are about energy dissipation with different horizontal face angles. In this paper, the realizable k-ε turbulence model was used to study the flow field and energy dissipation rates of different stepped spillways with five horizontal face angles in the skimming flow regions. It shows that the free water surfaces and energy dissipation rates change with horizontal face angles and the energy dissipation rates initially decrease and then increase as the horizontal face angle increases. And the horizontal face angles cause the great changes of flow field.

Solar energy is derived from photons of light coming from the sun in a form called radiation. Solar energy finds extensive application in air and water heating, solar cooking, as well as electrical power generation, depending on the way of capturing, converting and distribution. To enable such application, it is necessary to analyze the horizontal tilt angle of horizontal surfaces – in order that when the solar energy reaches the earth surface to be completely absorbed. This paper tends to describe the availability of solar radiation for south-facing flat surfaces. The optimal monthly, seasonal, and annual tilt angles have been estimated for Pristina. The solar radiation received by the incident plane is estimated based on isotropic sky analysis models, namely Liu and Jordan model. The annual optimum tilt angle for Pristina was found to be 34.7°. The determination of annual solar energy gains is done by applying the optimal monthly, seasonal and annual tilt angles for an inclined surface compared to a horizontal surface. Monthly, seasonal and annual percentages of solar energy gains have been estimated to be 21.35%, 19.98%, and 14.43%. Losses of solar energy were estimated by 1.13 % when a surface was fixed at a seasonal optimum tilt angle, and when it was fixed at an annual optimum tilt angle, those losses were 5.7%.

The reason for excessive multidecade deflections is still unclear after 70 years of the cantilever method that has been applied in building large-span segmental concrete bridges. The failure of the Koror-Babeldaob bridge gives the author a clue that the reason might be the boundary condition. The asymmetric properties of the bearing and prestress tendon draw the author’s attention. To understand the process of stress redistribution, the virtual stiffness method which is derived from the principle of minimum potential energy was created, and the phenomenon the author suggested named Material Inelasticity and Prestress Loss Coupling Effect is discovered. The unexplainable excessive deflection and prestress loss are found in the new load model. The calculation of excessive deflection is discussed. The new model fits the experience well. The optimization design methods and construction key points are proposed.

This paper presents an approach to the Euler-Bernoulli beam theory (EBBT) using the finite difference method (FDM). The EBBT covers the case of small deflections, and shear deformations are not considered. The FDM is an approximate method for solving problems described with differential equations. The FDM does not involve solving differential equations; equations are formulated with values at selected points of the structure. Generally, the finite difference approximations are derived based on fourth-order polynomial hypothesis (FOPH) and second-order polynomial hypothesis (SOPH) for the deflection curve; the FOPH is made for the fourth and third derivative of the deflection curve while the SOPH is made for its second and first derivative. In addition, the boundary conditions and not the governing equations are applied at the beam’s ends. In this paper, the FOPH was made for all of the derivatives of the deflection curve, and additional points were introduced at the beam’s ends and positions of discontinuity (concentrated loads or moments, supports, hinges, springs, etc.). The introduction of additional points allowed us to apply the governing equations at the beam’s ends and to satisfy the boundary and continuity conditions. Moreover, grid points with variable spacing were also considered, the grid being uniform within beam segments. First-order analysis, second-order analysis, and vibration analysis of structures were conducted with this model. Furthermore, tapered beams were analyzed (element stiffness matrix, second-order analysis). Finally, a direct time integration method (DTIM) was presented. The FDM-based DTIM enabled the analysis of forced vibration of structures, with damping taken into account. The results obtained in this paper showed good agreement with those of other studies, and the accuracy was increased through a grid refinement. Especially in the first-order analysis of uniform beams, the results were exact for uniformly distributed and concentrated loads regardless of the grid. Further research will be needed to investigate polynomial refinements (higher-order polynomials such as fifth-order, sixth-order…) of the deflection curve; the polynomial refinements aimed to increase the accuracy, whereby non-centered finite difference approximations at beam’s ends and positions of discontinuity would be used.

Background/Objectives: This study aims to investigate the influence of root canal morphology and various treatment variables on the outcomes of root canal treatments (RCT) in mandibular second molars, assessed through cone-beam computed tomography (CBCT) imaging. Methods: A total of 150 CBCT images were examined, comprising 100 cases of persistent endodontic infections and 50 from previously treated root canals with normal apices in mandibular second molars. CBCT was utilized to evaluate root canal configuration, the radiographic quality of coronal restorations and treated canal systems, and the presence of periapical lesions. Statistical analyses were performed to explore correlations between these factors. Results: The presence of a C-shaped root canal configuration did not demonstrate a significant correlation with periapical lesions (p=0.05). Factors influencing endodontic treatment outcomes included the presence of missing canals (p=0.018), underfilling or overfilling (p=0.045), and inadequate coronal restoration (p=0.006). The presence of a missing canal was identified as the variable most significantly associated with periapical lesions (OR=3.103). Leaky canals were more commonly observed in C-shaped root canals (p&lt;0.001). Conclusions: Regardless of the root canal morphology of mandibular second molars, successful RCT depends on thorough disinfection to eliminate any untreated canals, precise three-dimensional filling of the canals at the correct working length, and a securely sealed coronal restoration to prevent leakage.

Modal testing is a common step in aerostructure design, serving to validate the predicted natural frequencies and mode shapes obtained through computational methods. The strategic placement of sensors during testing is crucial to accurately measuring the intended natural frequencies. However, conventional methodologies for sensor placement are often time-consuming and involve iterative processes. This study explores the potential of machine learning techniques to enhance sensor selection methodologies. Three machine learning-based approaches are introduced and assessed, comparing their efficiency with established techniques. The evaluation of these methodologies is conducted using a numerical model of a beam to simulate real-world scenarios. The results offer insights into the efficacy of machine learning in optimizing sensor placement, presenting an innovative perspective on enhancing the efficiency and precision of modal testing procedures in aerostructure design.

Dental pulp chamber volume is a fundamental measurement in the field of endodontics, but also in forensic sciences, teaching and training, or tissue engineering. This study evaluates the precision of cone beam computed tomography (CBCT) in comparison with computed micro-tomography (micro-CT) in evaluating pulp chamber volume of upper central incisors ex vivo. The intra-operator and inter-operator error were evaluated, and the results for the two techniques were compared with a T-test for paired samples. Intra-operator and inter-operator errors were >0.05, indicating an adequate reproducibility in each operator and no significant differences between their meas-urements. On the other hand, no significant differences between the two measurement techniques. The present results demonstrate that CBCT is a precise, feasible and reproducible technique for evaluation of dental pulp chamber volume ex vivo. Results provided with this method are suitable for different medical branches but also for teaching and training of undergraduate and post-graduate students. Furthermore, the findings of this study carry significant clinical implications, as accurate assessment of pulp chamber volume is critical in the diagnosis and treatment of various endodontic conditions. The ability of CBCT to provide reliable 3D dental anatomy measurements can enhance the planning of endodontic treatments by allowing for a better understanding of internal tooth morphology. Additionally, the precision and reproducibility of CBCT in assessing pulp chamber volume can contribute to improved clinical outcomes and reduced complications during endodontic procedures. These findings further support the increasingly vital role of CBCT in modern clinical practice and underscore its value as an indispensable tool in the field of dentistry.

Liquid argon technology is widely used by many previous and current neutrino experiments, and it is also promising for future large-scale neutrino experiments. When detecting neutrinos using liquid argon, many hadrons are involved, which can also interact with argon nuclei. In order to gain a better understanding of detection processes, and to simulate neutrino events, knowledge of hadron-argon cross sections is needed. This paper describes a new procedure, which improves upon the previous work with a multi-dimensional unfolding, to measure hadron-argon cross sections in a liquid argon time projection chamber. Through a simplified version of simulation, we demonstrate the validity of this procedure.

(1) Background: This study evaluated the spatial position and anatomical characteristics related to impacted third molars by map-reading strategy using cone beam computed tomography (CBCT). (2) Methods: To determine the positioning of impacted third molars on CBCT it was used Winter's and Pell &amp; Gregory's classifications, and the presence of external root resorption in mandibular second molars were based on Herman´s classification. The relationship between the mandibular third molar root apex and the mandibular canal was also analyzed. Fisher’s exact test was used to comparative statistical analysis. The significance level considered was 5%. (3) Results: The results showed that according to Winter's classification, 48.06 % of impacted teeth were in the mesioangular position. Using Pell &amp; Gregory's classification, 43.22% of the impacted molars were in the position B and C, and 54.2% of the teeth were class II. 69.7% of teeth showed an absence of contact between the root apex and the mandibular canal and there was no occurrence of external root resorption in the distal of second molar in 88.7%. (4) Conclusions: The map-reading strategy using CBCT scans for anatomical positions and characteristics of impacted third molars increases professional confidence and establishes a parameter of quality and safety in the surgical procedure for the patient.

A novel concrete beam-column connection utilizing L-shaped steel bars is proposed to address the growing demand for prefabricated buildings and to ensure good seismic performance in such beam-column structures. After positioning two prefabricated beams with L-shaped tendons into the designated connection points at the top and bottom of the columns, concrete is poured into the post-cast section of the joint and the composite beam area, realizing a connection between the beams and columns. Quasi-static tests were performed on four combined nodes and one cast-in-place node to investigate their failure modes and stress mechanisms. Seismic performance indices, including hysteretic curves, skeleton curves, ductility performance, and energy dissipation capacity, were analyzed. Concurrently, the finite element method (FEM) was employed for parameter analysis. By integrating the test and FEM results, an equation for calculating the shear capacity of the connection was derived. The findings demonstrate that the hysteresis curve of the newly developed prefabricated joints is relatively full, with their overall performance index comparable to that of cast-in-place joints. Additionally, enhancing the post-casting area of concrete, the length of the L-shaped bars, the concrete strength in the composite beam region, the axial compression ratio, or the steel tube dimensions can effectively improve overall performance. The derived equation for the shear-bearing capacity of the connection satisfies design and application requirements.

Machine Learning (ML) has proved its capabilities in different scientific and industrial fields, but it needs to be further investigated in the construction industry for practical utilization. One of the use cases of ML is delegating the structural calculation process. In this study, to discuss ML’s capabilities in performing the work of a structural designer, calculations of concrete sections based on ACI (American Concrete Institute) as a case study were selected. At first, all manual design steps and standard considerations for a concrete beam section were coded parametrically in MATLAB. After comparing with structural design references to prove the accuracy of codes in calculating shear and bending capacities, the parametric results were used as initial data (Look−up table) for training the ML operators. Regarding different types of ML techniques and as a comparison between them, in the next steps, all essential codes for Fuzzy Logic (FL), Neural Network (NN) and Adaptive Neuro-Fuzzy Inference System (ANFIS) were coded in the same platform. The performance of the three coded ML operators to replace (delegate) standard calculations compared to direct calculations was individually investigated and displayed through parametric examples. After initial examples, the influences of the number of parameters and size of the Look−up table on the accuracy of each operator were discussed. The study concluded that although all three operators can delegate the standard calculation, the precision of the results differs considerably. In case of the desirable size of the Look−up table, ANFIS operators can represent the standard calculations with a different number of parameters and entirely high precision.

Cantilever beams are the most widely used form of strain-driven energy harvesting, which uses piezoelectric materials. Although researchers are constantly seeking improved power output from cantilever-beam-driven piezoelectric energy harvesters, a systematic and fundamental analysis of the effect of beam geometry on the power capacity of energy harvesters warrants further investigation. Most of the previous research accounts for beams that are fully coated with piezoelectric material. While a larger coating area increases energy output, it also escalates costs as piezoelectric materials are very expensive. Considering the high cost of piezoelectric materials when dealing with limited piezoelectric material, enhancing power output can be achieved by employing a larger base beam and coating a portion of it at the fixed end. As such, the aim of this work is to investigate a wide variety of cantilever beam shapes (e.g., trapezoidal, triangular, V-cut, concave, and convex) with partial piezoelectric material coating on the base beam to maximize the power output capacity of the harvester. To ascertain a comparable argument, the surface area, volume, and mass of all the considered beam shapes are kept consistent, as these parameters influence the power output of the harvester. The geometry of each shape is systematically varied to understand the effect of geometric configuration on the output power density. Finally, the power capacities of all types of beams are compared, and a design is proposed to obtain the maximum power output. It was found that when the surface area of both the beam and piezoelectric material is kept constant and piezoelectric material is located at the fixed end, a trapezoidal beam with a smaller base width and larger free end width is the most efficient in generating power as long as the structural integrity is maintained. The finding is completely opposite as was suggested by previous studies, which proposed that a trapezoidal beam with a smaller free end yields higher output. Instead, this study demonstrates that an inverted trapezoidal beam produced higher output, considering partial coating compared to the full beam coating used in previous studies. Additionally, a correlation is presented on how the beam resonance frequency shifts with variation in beam parameters.

The aim of this study is to compare different methods used for determination of the DS for sulfonated membranes before and after high dose irradiation. Commercial PEEK was homogenously sulfonated up to DS of 60-90% and the membranes were prepared using solvent casting method. Part of the samples were irradiated with 10 MeV electron beam up to 500 kGy dose to assess the ionising radiation induced effects. Both non-irradiated and irradiated membranes were characterized by Fourier Transformation infrared (FT-IR) spectrometry, thermogravimetric analysis (TGA), proton nuclear magnetic resonance (1H-NMR), electrochemical impedance analysis and for the first time for non-irradiated membranes by spectrophotometric analysis with Cr(III). Comparison of the above-mentioned methods for application for DS assessment was done. It was observed that irradiated membranes presented a higher value of DS. Appearance of different new signals in 1H-NMR and FT-IR spectra of irradiated membranes indicated the effects of radiation induced changes in the structure of SPEEK materials. It was determined that the novel method with Cr(III) is applicable for the determination of SPEEK DS under 80%.

Based on the prosed criterion of the type of heating, a classification of the sources of pulsed electron beams was carried out, for better understanding both the nature of the thermal processes occurring under irradiation and for predicting their suitability for certain applications. The melting thresholds of materials were calculated over the wide ranges of accelerating voltages and pulse durations. On the basis of calculations, a refractoriness series of metals for surface-volume pulsed heating was proposed.

Asphalt binder is a temperature sensitive material, whose performance is greatly affected by the climate change of the environment. Improper selection of asphalt will cause a lot of damage and affect the durability of the road. The establishment of asphalt pavement performance zoning in Xinjiang, a vast area with great temperature difference, will provide reference for the selection of asphalt suitability, the refinement of pavement design and the sustainable development of road engineering. In this study, 11 years of temperature data in Xinjiang region were collected and analyzed, and 98% reliability of pavement design temperature was used to draw a performance grading map of asphalt pavement in Xinjiang region based on ArcGIS platform. Finally, Xinjiang region was divided into 9 performance zones. At the same time, the performance grade (PG) of five kinds of asphalt binders in Karamay were explored. The result shows that there is little difference in continuous PG span between different matrix asphalt binders, the lower penetration grade, the better high temperature performance, the worse low temperature performance. After adding SBS modifier, the continuous PG span can be higher than the matrix asphalt in 20 ℃. All these provide the basis for reasonable selection of asphalt binders in different areas of Xinjiang.

FY-3E WindRAD (Fengyun-3E Wind Radar) is a dual-frequency rotating fan-beam scatterometer. Its data characteristics, NOC (NWP Ocean Calibration), and wind retrieval performance are investigated in this paper. The radar view geometry diversity varies across the swath, with maximum diversity in the sweet swaths and limited diversity in the outer and nadir swaths. When NOC backscatter calibration coefficients are computed as a function of incidence angle only (NOCint), a smooth correction is found. However, when relative antenna azimuth angle is included (NOCant), it appears that the corrections as a function of relative azimuth angle vary harmonically and substantially for a specific incidence angle. NOCant corrections yield a better fit of the measurements to the GMF (Geophysical Model Function). Hence NOCant is applied for the wind retrieval analysis from Ku-band, C-band. An extra engineering correction of 0.15dB and 0.2dB is applied on Ku-band and C-band backscatter values, respectively, to reduce the wind speed bias without increasing the standard deviation. Overall, NOCant is the best option for both channels. Also, the instrument backscatter data stability over time is good and the retrieved winds can fulfill operational requirements.

In the present study, piecewise integrated composite (PIC) bumper beam for passenger cars was proposed and design optimisation process for composite bumper beam against IIHS test was carried out with the help of machine learning. Several elements in IIHS bumper FE model have been assigned to be references, in order to collect training data which, allow the machine learning model to study the method of predicting loading types of each finite element. 2-D and 3-D implementations were provided by machine learning models, which determined stacking sequences of each finite element in PIC bumper beam. It was found that the PIC bumper beam, which was designed by machine learning model has direct impact on reducing the possibility of failure as well as increasing bending strength effectively than conventional composite bumper beam. Moreover, 3-D implementation produced better results compared with 2-D implementation since it was preferable to choose loading type information which was achieved from surroundings when the target elements were located either at corner or junction of planes instead of using information came from the same plane of target.

Recently, the interest in silicon-based detectors capable of detecting single photons in the near-infrared is growing mainly due to LiDAR applications, autonomous driving in particular. Silicon single-photon avalanche diodes are one of the most interesting single-photon NIR technology available on the market, nevertheless, their efficiency is hindered by the low absorption coefficient of Si in the NIR. The idea is the integration of CMOS-compatible nanostructures, specifically, silver grating array supporting Surface Plasmons Polaritons (SPPs), to confine superficially the incoming NIR photons and therefore increase photons probability to generate an electron-hole pair. The plasmonic silver array is geometrically fine-tuned using time domain simulation software to achieve maximum detector performance at 950 nm. Then, the plasmonic silver array is integrated by means of the focused ion beam technique on the detector. Finally, the integrated detector is electro-optically characterized, demonstrating a quantum efficiency of 13 at 950 nm, 2,2 times more than the reference detector. This result suggests the production of a device capable of detecting single NIR photons, at a very low cost and compatible with CMOS, thus integrable on existing technology platforms.

The main aspects of material research: material synthesis, material structure, and material properties, are interrelated. Acquiring atomic structure information of electron beam sensitive materials by electron microscope, such as porous zeolites, organic-inorganic hybrid perovskites, metal-organic frameworks, is an important and challenging task. The difficulties in characterization of the structures will inevitably limit the optimization of their synthesis methods and further improve their performance. The emergence of integrated differential phase contrast scanning transmission electron microscopy (iDPC-STEM), a STEM characterization technique capable of obtaining images with high signal-to-noise ratio under lower doses, has made great breakthroughs in the atomic structure characterization of these materials. This article reviews the developments and applications of iDPC-STEM in electron beam sensitive materials, and provides an outlook on its capabilities and development.

This research was conducted to manufacture thermally expandable microspheres (TEMs) for vehicles’ underbody coating and to apply them on an industrial scale. TEMs heat resistance was studied depending on the ratios of a cross-linking agent and an initiator. This research focused on the content of a cross-linking agent and how it affected the results. The TEMs’ outer shell was thickened to solve the problem of the foam expansion ratio’s reduction that occurred due to the shrinkage after the maximum expansion (Tmax) was reached. After foaming, the cross-sectional thickness and surface of the sample with thickened outer shell were observed. The TEMs with the thickened shell showed the least shrinkage, which indicated excellent shrinkage stability, even after prolonged exposure to heat.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In EBM process monitoring, data analysis for processed layer quality evaluation is currently focused on the extraction of information from the raw data collected in-EBM process, i.e. thermal/ optical / electronic images, and the comparison between the collected data and the Computed Tomography (CT)/ microscopy images generated post-EBM process. This article postulates that a stack of bitmaps could be generated from the 3D model at a range of Z heights during file preparation of the EBM process, and serve as a reference image set. In-EBM process comparison between that and the workpiece images collected during the EBM process could then be used for quality assessment purposes. In addition, despite the extensive literature on 3D model slicing and contour generation for AM process preparation, no methods regarding image generation from cross sections of the 3D models have been disseminated in details. This article aims to address this by presenting a piece of 3D model-image generation software. The software is capable of generating binary 3D model reference images with user-defined Region-of-Interest (ROI) of the processing area, and Z heights of the model. It is envisaged that this 3D model-reference image generation ability opens up new opportunities in quality assessment for the in-process monitoring of the EBM process.

Evaluating of long-term satellite-derived ocean color products using in-situ measurements is essential to ensure data quality and integrity. In this study, the Visible Infrared Imaging Radiometer Suite (VIIRS) remote sensing reflectance (Rrs) products were evaluated and analyzed by using long-term OC-CCI in-situ data from 2012 to 2021. The results demonstrate that the root mean square difference of VIIRS Rrs product accuracy in most bands is better than 0.002 (sr-1) when considering its average life span of 12 years. However, the VIIRS Rrs products in shorter wavelength bands (e.g., at 412 nm) had significantly lower accuracy in general and a long-term bias over the recent years. The annual precision of VIIRS Rrs products showed a declining trend especially in coastal or eutrophic waters. This accuracy deterioration of the VIIRS Rrs products suggests a strong need for continuous monitoring of its performance and further efforts on improving the atmospheric correction algorithm to specifically deal with satellite records at high SZAs and OZAs.

The research paper provides a mathematical framework for understanding phase shift in wave phenomena, bridging theoretical foundations with real-world applications. It emphasizes the importance of phase shift in physics and engineering, particularly in fields like telecommunications and acoustics. Key equations are introduced to explain phase angle, time delay, frequency, and wavelength relationships. The study also introduces the concept of time distortion due to a 1° phase shift, crucial for precise time measurements in precision instruments. The research also addresses infinitesimal wave energy loss related to phase shift, enriching our understanding of wave behavior, and impacting scientific and engineering disciplines.

This study entailed the design and analysis of a 400 m-class underwater glider operated by a bladder-type buoyancy engine. The underwater glider was designed for high-speed movement with a maximum velocity of 2 knots. The shape of the hull was designed to reduce water resistance using the Myring hull profile equation. The reliability was verified by performing simulations using resistance coefficients. The relationship between the control value of the ballast discharged from the buoyancy engine and the glider's speed according to the path angle was analyzed. Further, the relationship between the optimal glide angle and the design control value of the ballast was derived, and the optimal glider speed was estimated accordingly. Based on the analysis results, a bladder-type buoyancy engine was developed, and the maximum speed of the tested underwater glider was measured via sea trials.

Psychological readiness following Anterior Cruciate ligament Reconstruction (ACLR) correlates with different return to sport outcomes. However, the relationship between strength and power and psychological readiness remains unexplored. The aim of this study was to investigate the relationship between the Anterior Cruciate Ligament Return to Sport After Injury (ACL-RSI) scores and various hamstrings and quadriceps strength and power variables. Twelve participants (20.7±2.5 years old; 174.2±7.5 cm; 70.2±8.5 kg; 18.2±8.3% of body fat) who had an ACLR nine months or more before the study completed the ACL-RSI questionnaire and isokinetic strength testing of the hamstrings and quadriceps (60°.s-1 and 180°.s-1). Based on ACL-RSI scores, they were divided into “cases” and “controls”, deemed not psychologically ready and psychologically ready to return to previous sport performance (PILOS), respectively. The main findings are that quadriceps’ and hamstrings’ rate of torque development (RTD) and time since surgery were determinants of psychological readiness following ACLR. Furthermore, compared to controls cases showed significantly lower angle-specific quadriceps and hamstrings torque close to extension and lower RTD, but no difference in peak torque. These results suggest that physiotherapists should facilitate athletes’ RTS by focusing on the restoration of RTD and strength at angles close to full knee extension.

In order to perform multi-degree-of-freedom motion measurements of marine machinery such as ship-borne mechanical platform in an absolute environment without a reference, absolute measurement methods using acceleration sensors and tilt gyroscopes are typically employed. However, due to the influence of wave forces on ship-borne mechanical platform, the coupling between different degrees of freedom can cause mutual interference, resulting in significant sensor measurement disturbances that make efficient computation and real-time analysis challenging. Specifically, when ship-borne mechanical platform swings, the proof mass of the acceleration sensor produces an undesirable signal output in the vertical direction, which leads to imprecise acceleration integration, thereby affecting accurate motion collection and posture estimation. To address these challenges, by analyzing the influence of the inclination angle of the ship-borne mechanical platform on the sensor measurement, and using the working principle of the acceleration sensor and angle sensor, a correction method for the motion measurement of the ship-borne mechanical platform based on multi-sensor fusion is proposed. In this article, we first analyze the influence of inclination angle on the integral effect in the heave direction. Then the configuration using four groups of acceleration sensors to correct the integral effect is proposed. Finally, the optimal inclination angle is determined through Kalman filtering based on the measured value of angle sensors and estimated values from the acceleration sensor sets. Experiments have proved that the average error of the corrected heave displacement signal is 25.34 mm, which is better than the integral displacement signal of a single acceleration sensor. At the same time, the acceleration sensor is used to calculate the roll angle and pitch angle of the ship-borne mechanical platform, and combined with the angle sensor signal to perform Kalman filtering, which filters out the errors caused by the shaking and instability of the mechanical platform, and can more accurately estimate the true inclination of the platform. Therefore, this method can enhance the precision and accuracy of the ship-borne mechanical platform motion signal acquisition, providing more valuable experimental data for research in marine engineering and related fields.

This study aimed to compare the efficacies and safety of enhanced and standard monofocal intraocular lenses (IOLs) in eyes with early glaucoma. Patients with concurrent cataracts and open-angle glaucoma (OAG) were enrolled. They underwent cataract surgery with IOL implantation. Manifest refraction; monocular uncorrected distance visual acuity (UDVA), corrected distance visual acuity (CDVA), uncorrected intermediate visual acuity (UIVA), and uncorrected near visual acuity (UNVA); visual field (VF); contrast sensitivity (CS); defocus curves and questionnaires were assessed three months postoperatively. Thirty-four and 38 patients had enhanced and standard monofocal IOLs, respectively. The enhanced monofocal IOL provided better UIVA than the standard monofocal IOL (p = 0.003) but similar UDVA, CDVA and UNVA. The enhanced monofocal IOL had more consistent defocus curves than the standard monofocal IOL, especially at -1 (p = 0.042) and -1.5 (p = 0.026) diopters. The enhanced monofocal IOL provided better satisfaction (p = 0.019) and lower spectacle dependence (p = 0.004) than the standard monofocal IOL for intermediate vision, with similar VF and CS. In conclusion, the enhanced monofocal IOL is recommended for patients with OAG because they provide better intermediate vision, higher satisfaction, and lower dependence on spectacles than standard monofocal IOL, without worsening other visual outcomes.

Background: Prismatic cover test (PCT) is a gold standard assessment of strabismus angle, however it has a significant number of disadvantages which are eliminated in Strabiscan device. Methods: Patients with strabismus (n = 30) and a group of healthy subjects (n = 30) were given a detailed history and underwent ophthalmologic examinations (best corrected visual acuity assessment, cycloplegic autorefractometry, biomicroscopic examination of anterior and posterior part of the eye). Each patient and healthy subjects were then subjected to the PCT, and then the presence of strabismus was detected, and its angle assessed using a Strabiscan demonstrator. Statistical analysis was done with Statistica software. Results: No statistically significant differences were noted in the measurements of strabismus angles made by the differing methods. Among the control group, using the Strabiscan demonstration device, low-angle latent strabismus ≤3PD was diagnosed in 83% of patients, and >3PD in 13% of patients. Those using the PCT, on the other hand, diagnosed latent strabismus ≤3PD in only 13% of patients, and latent strabismus with an angle >3PD in 13% of patients. Conclusion: The Strabiscan demonstration device provides quick and accurate assessment of the strabismus angle.

We describe the behavior of mixtures of stearic acid (SA) and its hydroxylated counterpart 12-hydroxystearic acid (12-HSA) in aqueous mixtures at room temperature, as function of the 12-HSA/(fatty acid) mole ratio R. The morphologies of the self-assembled aggregates are obtained by a multi-structural approach that combines confocal and cryo-TEM microscopies with Small-Angle Neutron Scattering (SANS) and Wide-Angle X-Rays Scattering (WAXS) measurements, coupled with rheology measurements. Fatty acids are solubilized by an excess of ethanolamine counterions, so that their heads are negatively charged. The behavior is driven by the competition between mixing entropy and enthalpic effects. A clear trend towards partitioning between the two types of fatty acids is observed, presumably driven by the favorable formation of a H-bond network between hydroxyl OH function on the 12th carbon. For all R, the self-assembled structures are locally lamellar, with bilayers composed of crystallized and strongly interdigitated fatty acids. At high R, multi-lamellar tubes are formed, similarly as for pure aqueous solutions of 12-HSA. The doping by a low amount of SA molecules only slightly modify the dimensions of the tubes (radius and length), and slightly decreases the bilayers rigidity. The solutions have a gel-like behavior originating from entanglements between tubes and show a yield stress. At intermediate R, a partial local partitioning occurs between the two types of fatty acids. The tubes coexist in solution with helical ribbons. The two structures possibly merge to form very long snaky objects with straight and curved parts. The rigidity of the bilayers and the rheological behavior of the solutions are very similar to those of the high R case. At low R, local partitioning also occurs, and the architecture of the self-assemblies associates the two morphologies of the pure fatty acids systems, respectively 2-D planar bilayers for SA and the tubes describe above for the 12-HSA molecules: they are facetted objects with planar domains enriched in SA molecules, capped with curved domains enriched in 12-HSA molecules. The rigidity of the bilayers is strongly increased, as well their storage modulus, compared to systems with larger R. The solutions remain however viscous fluids in this regime of low R.

We describe the design and fabrication of an industrial injection moulding system which can be mounted and used on the NCD-SWEET Small-angle X-Ray Scattering Beamline at ALBA. We show how highly useful time-resolved data can be obtained using this system. We are able to evaluate the fraction of material in the mould cavity and identify the first material to solidify and how this varies with the injection tem-perature. The design follows current industrial practice and provides opportunities to collect time-resolved data at several points within the mould cavity so we can build up a 4D perspective of the morphology and its temporal development. The quantitative data obtained will prove invaluable for the optimisation of the next generation of in-jection moulding techniques. This preliminary work used results from the injection moulding of a general purpose isotactic polypropylene.

The main goal of this paper is to study the weak gravitational lensing by Horndeski black hole in weak field approximation. In order to do so, we exploit the Gibbons-Werner method to the optical geometry of Horndeski black hole and implement the Gauss-Bonnet theorem to accomplish the deflection angle of light in weak field region. Furthermore, we have endeavored to extend the scale of our work by comprising the impact of plasma medium on the deflection angle as properly. Later, the graphical influence of the deflection angle of photon on Horndeski black hole in plasma and non-plasma medium is examined.

The adoption of Pump as Turbines (PATs) both in small scale hydroelectric plants and water supply systems has brought different advantages, the most recognized being cost-effectiveness as compared to other hydroturbines. However, due to their lack of flow control ability, their intolerance to off-design operations constitutes one tough shortfall. Moreover, this technology’s newness leads to PAT flow dynamics still being ununderstood even to date. Therefore, this study intends to numerically investigate the mixed flow PAT’s pump mode flow dynamics for five operating conditions expanding from optimum (1QBEP) to deep part-load (0.41 QBEP) conditions. Moreover the effect of runner blade angle on the same has been investigated where three angles namely -2°, 0°, and 2° have been considered. PAT flow stability was found to deteriorate as the flow decreased, where associated pressure pulsation level worsened at different flow zones. In addition, the blade angle increase led correspondingly increasing flow unsteadiness and pressure pulsation levels, where the pulsation frequencies from rotor-stator interactions were dominant for most of flow zones. This study’s findings are of a crucial importance to both scientific and engineering communities as they contribute to thorough understanding of PAT flow dynamics.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

Purpose is to o review the pathogenic mechanism for ocular hypertension and glaucoma development after pars plana vitrectomy. Both acute and chronic causes are considered and special attention is paid to the theories and clinical evidence on the risk of developing Open Angle Glaucoma (OAG) after Pars Plana Vitrectomy (PPV). Most existing scientific literature on the issue agree on the role of ascorbate as an oxygen scavenger within the vitreous chamber. Oxygen tension in the vitreous and anterior chamber is maximum inn proximity of the retinal surface and endothelium, respectively and steeply decreases toward the lens; on both sides, and trabeculate. Vitreous removal and, to a lesser extent, liquefaction, greatly reduces oxygen tension gradient in vitreous chamber while cataract extraction has similar effects on anterior chamber oxygen gradients. Oxygen derivatives originated from the cornea and retina are actively reduced by the vitreous gel and/or the crystalline lens. Vitreous removal and cataract extraction reduce drastically this function. Most reported clinical series confirm this hypothesis although protocol difference and follow-up length greatly impact the reliability of results.

In this paper, first we use the optical metrics of black-bounce traversable wormholes to calculate the Gaussian curvature. Then we use the Gauss-Bonnet theorem to obtain the weak deflection angle of light from the black-bounce traversable wormholes. Then we investigate the effect of dark matter medium on weak deflection angle using the Gauss-Bonnet theorem. We show how weak deflection angle of wormhole is affected by the bounce parameter $a$. Using the Gauss-bonnet theorem for calculating weak deflection angle shows us that light bending can be thought as a global and topological effect.

In this paper, we discuss the weak gravitational lensing in the context of stringy black holes. Initially, we examine the deflection angle of photon by charged stringy black hole. For this desire, we compute the Gaussian optical curvature and implement the Gauss-Bonnet theorem to investigate the deflection angle for spherically balanced spacetime of stringy black hole. We also analyze the influence of plasma medium in the weak gravitational lensing for stringy black hole. Moreover, the graphical impact of coupling constant $\alpha$, impact parameter $b$ , black hole charge $Q$ on deflection angle by charged stringy black hole has been studied in plasma as well as non-plasma medium.

Running on a non-motorized, curved-deck treadmill is thought to improve gait mechanics. It is not known, though, if the change in gait carries over to running on a motorized treadmill or level ground. To determine the effect of running on a curved non-motorized treadmill (CNT) on gait characteristics measured during a subsequent bout of running on a traditional motorized treadmill (TMT). Sixteen healthy college-aged participants, age (mean±SD) 20.4±1.6 years volunteered to have their gait analyzed while running on a TMT and CNT. After familiarization and warm-up on both treadmills, each subject completed five, 4-minute bouts of running alternating between traditional motorized and curved non-motorized treadmills: TMT-1, CNT-1, TMT-2, CNT-2, and TMT-3. Variables of interest included step length (m), stride length (m), imbalance score (%), and step angle (°) and were measured using Optogait gait analysis equipment. Differences in gait char acteristics among TMT-1, TMT-2, and TMT-3 can be attributed to running on the CNT. The results show that running on a CNT resulted in significant changes in gait characteristics. These findings suggest that running on a CNT can significantly alter gait characteristics may result in improvements in running gait that persist to subsequent running on a TMT.

Purpose: To compare the therapeutic efficacy and safety of dorzolamide/timolol fixed-combination in newly diagnosed primary open angle glaucoma patients. Methods: In this prospective, interventional case series, newly diagnosed primary open angle glaucoma (POAG) patients that had not been treated for glaucoma were included. Patients were started on Cosopt twice a day (BID) for 1 month and then switched to three times a day (TDS) for additional 1 month. Patients underwent comprehensive ophthalmic examination, diurnal intraocular pressure (IOP), blood pressure (BP) and 24-hours heart rate (HR) measurements at baseline, month 1( BID), and month 2( TDS). IOP, systolic and diastolic pressures were measured at 8:00 AM,12:00 AM, 4:00 PM, 8:00 PM and 12:00 PM. Throughout the study, all adverse events were recorded and monitored by the investigators. Results: In 31 POAG patients that completed the study ,mean baseline IOP was 23.1±3.15 mmHg . IOP was decreased significantly 16.5 ± 2.21 at 1 month (P < 0.0001) and 13.9 ± 2.23 mmHg at 1 and 2 month follow up. (P < 0.0001) IOP was significantly lower in month 2 compared to month 1 (P = 0.0004). While Cosopt BID significantly reduced the mean 24-hour systolic BP and mean 24-hour HR from baseline (P < 0.0001), the mean 24-hour systolic BP and HR remained unchanged 2ith Cosopt TDS compared to BID (P = 0.62). Conclusions: Cosopt TDS has a superior IOP-lowering effect than Cosopt BID in POAG patients with comparable safety profile.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

In this paper, an adaptive technology and the interconnection and damping assignment passivity-based control method are combined to solve the stabilization problem for underactuated mechanical systems with uncertainties (including matched and unmatched). Uncertainties include unknown friction coefficients and unknown terms in kinetic energy and potential energy. A novel adaptive interconnection and damping assignment passivity-based control scheme is proposed and an adaptive stabilization controller is designed to make the closed-loop system locally stable. Verification is conducted on the ball and beam system, taking into account uncertainties of friction coefficients, kinetic energy, and potential energy. The locally asymptotic stability is demonstrated using the LaSalle’s invariance principle and approximate linearization. The effectiveness of the proposed control law is verified through numerical simulations.

The results of electron-beam processing of Mn-Zn ferrite samples using pulsed and continuous electron beams in the forevacuum pressure range (10 Pa) are presented. We find that continuous electron-beam processing leads to surface structuring of the ferrite, changes in elemental composition on the surface, and electrical property modification. The degree of ferrite parameter changes exhibits a threshold behavior. For surface processing temperatures below 900 °C, changes are barely noticeable, while for temperatures over 1100 °C the surface resistance decreases by more than an order of magnitude. Electron-beam processing with millisecond pulse duration and pulse energy density exceeding 15 J/cm² results in the formation of low zinc content melt islands, while the remaining surface area (outside the islands) elemental content and ferrite properties remain largely unchanged. The thickness of the modified layer depends on the processing mode and can be controlled over the range 0.1–0.5 mm. Because of its low resistance, the modified layer can be utilized to enhance the RF-absorbing properties of the ferrite.

Background and Objectives: The prevalence of osteoporosis is high, reportedly affecting 200 million people worldwide. A major problem associated with osteoporosis is that femoral fractures cause a decline in general function and loss of independence, greatly reducing patients’ quality of life. Notably, osteoporosis is an asymptomatic chronic metabolic disease, and its detection is thus often delayed. Interestingly, mandibular cortical index (MCI) classification using dental panoramic radiography is reportedly useful for early detection of osteoporosis. However, this visual classification method can lead to differences in diagnosis among surgeons. Therefore, this preliminary study was performed to analyze cone-beam computed tomography (CBCT) data and examine an objective MCI classification using the findings obtained. Materials and Methods: MCI classification (classified as C1, C2, or C3) was performed by three examiners on 70 women (91 sites) aged ≥20 years. The mandibular cortical width of all sites was measured using CBCT images. Results: The results showed that the mandibular cortical width was not particularly correlated with age or number of present teeth, and no significant quantitative differences were found between C1 and C2. However, coronal CBCT images of C2 revealed multiple characteristic bone trabecular structures. Conclusions: These structures may be an important finding affecting the classification of two-dimensional dental panoramic radiography images.

GaN nanowires grown on metal substrates attract an increasing interest for a wide range of applications. Herein, we report GaN nanowires grown by plasma-assisted molecular beam epitaxy on thin polycrystalline ZrN buffer layers, sputtered onto Si(111) substrates. The nanowire orientation is studied experimentally and described within a model as a function of the Ga beam angle, nanowire tilt angle and substrate rotation. We show that vertically aligned nanowires grow faster than inclined nanowires, which leads to an interesting effect of geometrical selection of the nanowire orientation in the directional molecular beam epitaxy technique. After a given growth time, this effect depends on the nanowire surface density. At low density, the nanowires continue to grow with random orientations as nucleated. At high density, the effect of preferential growth induced by unidirectional supply of material in MBE starts to dominate. Faster growing nanowires with smaller tilt angles shadow more inclined nanowires that grow slower. This helps to obtain more regular ensembles of vertically oriented GaN nanowires despite their random position induced by the metallic grains at nucleation. The obtained dense ensembles of vertically aligned GaN nanowires on ZrN/Si(111) surfaces are highly relevant for device applications. These results are not specific for GaN nanowires and should be relevant for any nanowires which are epitaxially linked to the randomly oriented surface grains in the directional molecular beam epitaxy.

Since the development of CBCT had been utilized in dentistry, the images of the CBCT can assist the surgeon to evaluate the anatomy carefully. Despite the value of the radiology evaluation, the implant procedures may require additional consideration rather than only evaluating the anatomical factors. The purpose of this study is to evaluate the predictability of using CBCT alone to plan for implant placement on the edentulous patient digitally CBCT images were analyzed by clinicians, measuring the ridge heights and widths of 4 selected implant sites in the maxillary and 2 selected implant sites in the mandibular arches for 91 patients planning for the implant-supported overdenture. (A total of 47 patients out of the 91 had completed the implant placement on the edentulous ridge, contributing to 55 upper and/or lower arches (136 dental implants). . Both predictabilities are low, implying the CBCT planning for implant placement on the edentulous ridge is not a good index and is insufficient to predict the surgical procedures as a solo method. The finding of this study indicates that digital planning by CBCT is insufficient to serve as an individual tool to predict implant procedures. Further information and evaluation must be considered for implant placement on the edentulous ridge.

In this study, Brillouin optical time-domain analysis (BOTDA) sensing technology was utilized for monitoring settlement in a similarity model of a highway subgrade. As contact winding cannot be used for an optical fiber that is buried directly in soil, uncoupling between. the fiber and the soil can occur. Thus, an optical-fiber-embedded beam (OFEB) was developed, and a method for measuring and calculating the beam deformation was proposed. A calibration test and a test on a similarity model of a subgrade were carried out to investigate the applicability and monitoring accuracy of the OFEB. It was concluded that the OFEB can accurately measure beam deflection, where the maximum relative error between measurements by the optical fiber and a displacement transducer was approximately 5%. The OFEB was embedded directly into a similarity model of a subgrade to monitor settlement. The deflection deformation of the OFEB was found to be close to the subgrade settlement over a certain settlement range with a relative error below 8.1%. Thus, the OFEB can be used to realize measure large-range distributed settlement in a subgrade. A numerical simulation was performed to identify appropriate beam dimensions and material design parameters, thereby extending the measurement range before decoupling of the OFEB and soil occurs. The enhancement of the measurement range and accuracy of the OFEB based on the preliminary experiments carried out in this study enables further investigation of settlement monitoring.

In the computational prediction of bridge vibrations due to high-speed train traffic, the most accurate results can be obtained by considering the interaction dynamics between the train, the superstructure, and the supporting structure. To achieve this, a detailed understanding of the coupling properties of all elements is crucial as they significantly influence the calculated vibrations. The studies in this article investigate the influence of different levels of modeling complexity on the computational acceleration results of single-span girder bridges with a ballasted superstructure. A numerical study on an extensive parameter field of single-span girder bridges is conducted to investigate the influence of modeling the bridge structures as coupling beams, i.e., by considering them as two vertically coupled beams representing the track (rails and sleepers) and the supporting structure. The connection between both beams reflects the stiffness and damping properties of the ballasted superstructure and can reproduce its load-distribution capacity. The excitation is applied as either a moving load or a multi-body model of the train, an Austrian Railjet, to evaluate interdependencies of interaction effects between the vehicle and track, and between track and bridge structure. The reference model is a simply-supported Bernoulli-Euler beam excited by moving axle loads. The comparison of acceleration results allows for identifying critical combinations of structural and train parameters for which the implementation of interaction dynamics has a particularly significant impact on the calculated vibrations and quantifying that impact. These findings provide the possibility of formulating structure-dependent recommendations concerning the targeted application of more complex modeling of the structure (coupling beam model) on the one hand and train (multi-body model) on the other.

The calculation of moments of area is one of the most fundamental aspects of engineering mechanics for calculating the properties of beams or for the determination of invariants in different kind of geometries. While a variety of shapes such as circles, rectangles, ellipses or their combinations can be described symbolically, such symbolic expressions are missing for freeform cross-sections. In particular, periodic B-spline cross-sections are suitable for an alternative beam cross-section, e.g. for the representation of topology optimization results. In this work, therefore, a symbolic description of the moments of area of various parametric representations of such B-splines is computed. The expressions found are then compared with alternative computational methods and checked for validity. The resulting equations show a simple way for fast conceptual computation of such moments of area of periodic B-splines.

Evaluating the integrity of structures is an important issue in engineering applications. The use of vibration-based techniques has become a common approach to assessing cracks, which are the most often occurring damage in structural elements. When involving an inverse method, it is necessary to know the influence of the position and the geometry of the crack on the modal parameter changes. The geometry of the crack, both in size and shape, defines the damage severity (DS). In this study, we present a method (DS-SHC) used for estimating the DS for closed and open transverse cracks in beam-like structures by using the intact and damaged beam deflections under its weight and a Stochastic Hill Climbing (SHC) algorithm. After describing the procedure of applying DS-SHC, we calculate for a prismatic cantilever beam the severities for different crack types and depths. The results are tested by comparing the DS obtained with DS-SHC with those acquired from dynamic tests made using professional simulation software. We obtained a good fit between the severities determined in these two ways. Afterward, we performed laboratory experiments and find out that the severities obtained with the DS-SHC method can accurately predict the frequency changes due to the crack. Hence, these severities are a valuable tool for damage detection.

Organic-organic interactions play important roles in the secondary organic aerosol formation, but the interactions are complex and poorly understood. Here we use environmental molecular beam experiments combined with molecular dynamics simulations to investigate the interactions between methanol and nopinone, as atmospheric organic proxies. In the experiments, methanol monomers and clusters are sent to collide with three types of surfaces, i.e., graphite, thin nopinone coating on graphite and multilayer surfaces, at temperatures between 140 K and 230 K. Methanol monomers are efficiently scattered from the graphite surface, whereas the scattering is substantially suppressed from nopinone surfaces. The desorption from the three surfaces is similar, suggesting that all the surfaces have weak or similar influences on the methanol desorption. The molecular dynamics results show that upon collisions the methanol clusters shatter, and the shattered fragments quickly diffuse and recombine to clusters. The desorption involves a series of processes, including detaching from clusters and desorbing as monomers. The experimental results also show that all trapped methanol molecules completely desorb within a short experimental time scale at temperatures of 180 K and above. At lower temperatures, the desorption rate decreases, and a long experimental time scale is used to resolve the desorption, where three desorption components are identified. The fast component is beyond the experimental detection limit. The intermediate component exhibits multi-step desorption character and has an activation energy of E_a = 0.18 ± 0.03 eV, in good agreement with simulation results. The slow desorption component is related to diffusion processes due to the weak temperature dependence.

An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

Today, contamination from heavy metals in the atmosphere is a global concern. Efficient detection techniques are therefore necessary if heavy metal exposure levels in different media are to be determined. The voltammetry method for in situ detection of heavy metal ions is a very sensitive electrochemical method. This thesis explores emerging developments in electrode alteration, materials production and experimental optimization. An electrochemical sensing platinum nanoparticle in the tantalum electrode is provided by means of an Ion Beam Sputtering Deposition (IBSD). The electrode was made with a Pt solution, sputtered simultaneously with hydrochloric acid corrosion on tantalum substrate. In the study of heavy metal ions, for example, the platinum nanoparticle electrodes as prepared were used Square wavelength voltammetry (OSWV) Hg²⁺, Cu²⁺ and Ag²⁺. The porous electrodes were observed in a broader range by the Pt nanostructure electrode for heavy metal ions. Furthermore, the susceptibility to detection has been shown to be saturated as the thickness of the layer electrode exceeded 50 nm. For Hg²⁺ 0,003-1 M, for Cu²⁺ 0,005-3 M and for Ag²⁺ the linear detection scale is 0,009-4 M. There has also been good reusability and repeatability. In addition, a scan electron microscope (SEM) used to study platinum electrode forming process and nanostructure. This electrode will have interesting applications in sensing systems.

Knowledge of a lasers beam’s profile throughout a laser system and experiment can help immensely in diagnosing laser problems and assisting in beam alignment and focusing at a sample. Obtaining such profiles is a trivial task in the ultraviolet-visible wavelength range but more challenging with near-infrared to infrared beams. Scientific grade bolometer arrays, suitable for such a task, do exist but are extremely costly, relatively large and have a large pixel size, of the order of 80 μm, which is adequate for profiling larger beams but poses an issue when trying to profile sub 100 μm beams for example at a focal point. This communication identifies a micro-bolometer array for near- to mid-infrared laser beam profiling, which is extremely low cost. In addition, the device is very compact, enabling use in confined spaces, and has a small, 12 μm, pixel size permitting the profiling of focused laser beams. The best scientific grade device identified has a pixel size of 17 μm. This device is a powerful tool for infrared laser spectroscopists, reducing the time required to measure the spot size of beams and to achieve spatial overlap of multiple infrared beams as used in two-dimensional infrared spectroscopy, saving many hours of setup time. The use of the bolometer array as a spectrographic detector and probe of long-term beam drifts is also demonstrated.

We investigate molecular beam epitaxy growth conditions of micrometers-thick In0.52Al0.48As designed for waveguide of InGaAs/InAlAs/InP quantum cascade lasers. Effect of growth temperature and V/III ratio on the surface morphology and defect structure were studied. The growth conditions which were developed for the growth of cascaded In0.53Ga0.47As/In0.52Al0.48As active region, e.g. growth temperature of TG=520°C and V/III ratio of 12, turned out to be not optimum for the growth of thick In0.52Al0.48As waveguide layers. It has been observed that after exceeding ~1µm thickness the quality of In0.52Al0.48As layers deteriorates. The in-situ optical reflectometry showed increasing surface roughness caused by defect forming, which was further confirmed by High Resolution X-Ray reciprocal space mapping, optical microscopy and atomic force microscopy. The presented optimization of growth conditions of In0.52Al0.48As waveguide layer led to the growth of defect free material, with good optical quality. This has been achieved by decreasing the growth temperature to TG=480 °C with appropriate increasing V/III ratio. At the same time the growth conditions of the cascade active region of the laser were left unchanged. The lasers grown using new recipe have shown lower threshold currents and improved slope efficiency. We relate this performance improvement to reduction of the electron scattering on the interface roughness and decreased waveguide absorption losses.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. In-process EBM monitoring for quality assurance purposes has been a popular research area. Electronic imaging has recently been investigated as one of the in-process EBM data collection methods, alongside thermal/ optical imaging techniques. Despite certain capabilities of an electronic imaging system have been investigated, experiments are yet to be carried out to benchmark one of the most important features of any imaging systems – spatial resolution. This article addresses this knowledge gap by: (1) proposing an indicator for the estimation of spatial resolution which includes the Backscattered Electrons (BSE) information depth, (2) estimating the achievable spatial resolution when electronic imaging is carried out inside an Arcam A1 EBM machine, and (3) presenting an experimental method to conduct edge resolution evaluation with the EBM machine. Analyses of experimental results indicated that the spatial resolution was of the order of 0.3mm-0.4mm when electronic imaging was carried out at room temperature. It is believed that by disseminating an analysis and experimental method to estimate and quantify spatial resolution, this study has contributed to the on-going quality assessment research in the field of in-process monitoring of the EBM process.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

The present work proposes a novel manufacturing technique based on the combination of Laser Metal Deposition, Laser Beam Machining and Laser Polishing processes for the complete manufacturing of complex parts. Therefore, the complete process is based on the application of a laser heat source both for the building of the preform shape of the part by additive manufacturing and for the finishing operations. Their combination enables to manufacture near-net-shape parts and afterwards, remove the excess material via laser machining, which has resulted to be capable of eliminating the waviness resulting from the additive process. Besides, surface quality is improved via laser polishing to reduce the roughness of the final part. Therefore, conventional machining operations are eliminated, what results in a much cleaner process. In order to validate the capability of this new approach, the dimensional accuracy and surface quality of the resulting parts are evaluated. The process has been validated on an Inconel 718 test part, where a previously additively built up part has been finished by means of laser machining and laser polishing.

The study aimed to analyze thoracic and lumbar erector spinae muscle activations during 3D elongation exercises in individuals with adolescent idiopathic scoliosis (AIS). Participants included 24 adolescents, meeting specific criteria such as a Cobb angle between 10° and 20°, and not having undergone surgical or brace treatments. EMG data were collected to evaluate muscle activations. The study found no significant interaction between exercise type and the side of the curve, but a significant main effect of exercise type on muscle activation, irrespective of Cobb angle. Different exercise types significantly affected muscle activity, with the highest activations in the TheraBand exercise, followed by manual and without equipment conditions. This suggests that exercise type significantly impacts muscle engagement in AIS patients, providing valuable insights for targeted exercise program design. The study, however, focused on short-term muscle activation, not long-term Cobb angle progression, pointing to the need for further research in this area.

The flow properties of pellets or granules are crucial for further processing the drug dosage forms. Optimal compression or filling the multiparticulate dosage forms into capsules is influenced by forces between discrete particles, which could be partially characterized by flow properties. Several techniques were developed for the examination of flowability, including static and dynamic methods applying empirical studies and the up-to-date chaos theory; however newest methods seem only to be powerful with the supplement of empirical principles. Our experiments try to refine both the technique of analysis and the methods by finding new, alternative ways. Our approach to the flowability measurements was to set up a dynamic time-dependent model which combines empirical observations and the chaos theory on a geometrical basis, thus find new aspects regarding flow properties of pellets and granules that could be relevant for drug developers.

Many probability-based uncertainty quantification (UQ) schemes require a large amount of sampled data to build credible probability density function (PDF) models for uncertain parameters. Unfortunately, the data collected in compressor blades of aero-engine are mostly limited due to expensive and time-consuming tests. In this paper, we develop a preconditioner-based data-driven polynomial chaos (PDDPC) method that can efficiently deal with uncertainty propagation of limited sampled data. The calculation accuracy of PDDPC method is closely related to the sample size of collected data. Therefore, the influence of sample size on PDDPC method is investigated using a nonlinear test function. Subsequently, we consider the real manufacturing errors of stagger angle for compressor blades. Under three different operating conditions, PDDPC method is applied to investigate the effect of stagger angle error on UQ results of multiple aerodynamic parameters of a two-dimensional compressor blade. The results show that as the sample size of measured data increases, UQ results of aerodynamic performance obtained by PDDPC method gradually converge. There exists a critical sample size that ensures accurate UQ analysis of compressor blades. The probability information contained in the machining error data is analyzed through Kullback-Leibler divergence, and the critical sample size is determined. The research results can make a valuable reference for the fast and cheap UQ analysis of compressor blades in practical engineering.

Star image registration is the most important step in the application of astronomical image differencing, stacking and mosaicking, which requires high robustness, accuracy and real--time of the algorithm, but there is no high--performance registration algorithm in this field. In this paper, we propose a star image registration algorithm that relies only on radial module features (RMF) and rotation angle features (RAF), which has excellent robustness, high accuracy, and good real--time performance. The test results on a large amount of simulated and real data show that the comprehensive performance of the proposed algorithm is significantly better than the four classical baseline algorithms in the presence of rotation, insufficient overlapping area, false stars, position deviation, magnitude deviation and complex sky background, which is a more ideal star image registration algorithm.

The authors recently proposed a method for on-site dosimetry by a combination of radiochromic film and portable colorimeter. To test and expand the applicability of this method, dosimetric properties of radiochromic reactions were examined for six combinations of two popular Gafchromic films (EBT3 and EBT-XD) and three commercially-available portable colorimeters (nix pro2, nix spectro2 and Spectro1 Pro; abbreviated to “NixP”, “NixS” and “SpoP”, respectively). EBT3 and EBT-XD were irradiated with 160 kV X-rays at 0.3 to 40Gy and 1 to 80 Gy, respectively, and the radiation-induced color levels of RGB and CMMK components were measured with the three colorimeters. Angle dependence was examined by reading at 15° intervals. As results, it was judged that all combinations would work effectively as tools for on-site dosimetry. NixP and NixS showed advantages that they were applicable to a wider dose range for both films, while Spo1 worked better in a lower dose range. On the other hand, Spo1 had an advantageous feature of no angular dependence in reading films, while NixP and NixS showed significant angle-dependent changes. These differences were presumed to attribute to the different geometries of LED light emission; it came from all directions (ring-shape source) in Spo1, 4 directions in NixP, and 8 directions in NixS. These findings would expand the applicability of the proposed on-site dosimetry method to various occasions.

The bridge crane is often used in a complex environment, often subject to interference of all loads. Some uncertainties factors often have an inevitable impact on its swing. So the force situation of the bridge crane during a working cycle is analyzed, and a three-dimensional dynamic mathematical model of the bridge crane is built. Through the simulation analysis of the model under the action of driving force and wind load, the change law of the swing angle of the bridge crane is studied. Then, the fuzzy control theory is used to determine the control parameter in the anti sway control process. The position, swing angle deviation and deviation rate of the bridge crane are taken as the input, and the parameter correction is obtained after the fuzzification by using the center of gravity method, the anti sway fuzzy control system of the bridge crane is designed and simulated. The research results show that the fuzzy PID anti sway controller can not only improve the adaptability of the control system, but also overcome the large overshoot, quickly restrain the swing, and effectively realize the anti sway function of the bridge crane.

Underwater acoustic spiral sources are able to generate spiral acoustic fields where the phase depends on the bearing angle. It allows to estimate the bearing angle relatively to a receiver by subtracting the phases of a spiral and a circular wavefront, and finds application in the bearing angle estimate with a single hydrophone, e.g., for unmanned underwater vehicles localization. This paper presents a new prototype for a spiral acoustic source, which is able to generate the required wavefronts, and is composed of four monopoles in the same piezoceramic cylinder. This paper reports the prototyping and the acoustic tests performed in a water tank where the spiral source was characterized in terms o Transmitting Voltage Response, phase, and horizontal and vertical directivity patterns. A receiving calibration method for the spiral source is proposed and shows a maximum angle error of 1 degree when the calibration and the operation are carried under the same conditions and a mean angle error up to 6 degrees for frequencies above 25 kHz when the same conditions are not fulfilled.

Low charge density nanometric ions were recently shown to bind strongly to neutral hydrated matter in aqueous solution. This phenomenon, called (super-)chaotropic effect, arises from the partial dehydration of both, the nano-ion and the solute, leading to a high gain in enthalpy. Here, we investigate the chaotropic effect of the polyoxometalate α-PW12O403- on the triblock copolymer P84: (EO)19(PO)43(EO)19 with (EO)19 the polyethoxylated and (PO)43 the polypropoxylated chains. The combination of phase diagrams, spectroscopic (nuclear magnetic resonance) and scattering (small angle neutron/X-ray scattering) techniques reveals that (i) below the micellization temperature of P84, PW12O403- exclusively binds to the propylene oxide moiety of P84 unimers and (ii) above the micellization temperature, PW12O403- mostly adsorbs on the ethylene oxide micellar corona. The preferential binding of the PW12O403- to the PPO chain over the PEO chains suggests that the binding is driven by the chaotropic effect and reinforced by the hydrophobic effect. At higher temperatures, the copolymer micellization leads to the displacement of PW12O403- from the PPO chain to the PEO chains. This study deepens the understanding of the subtle interplay between the chaotropic and hydrophobic effects in complex salt-organic matter solutions.

Drought decreases grain yield of sorghum [Sorghum bicolor (L.) Moench], and understanding the mechanism(s) related to drought tolerance is critical for sustaining sorghum production. Variation in root and shoot traits associated with drought tolerance were analyzed to provide an integrated view of factors that underlie the drought tolerance of sorghum. The plants were grown in the root column up to the five-leaf stage, then exposed to either 0.9 fraction of transpirable soil water (FTSW) or 0.4 FTSW for five days. In another experiment, at the five-leaf stage, stress was imposed for 14 days. Various root and shoot traits associated with drought tolerance were recorded. The seminal root angle of IS13540 was lower (24.4) than IS23143 (42.6). Drought stress increased the maximum root length (40%) and total root length (58%) of IS13540 than its irrigated control. In contrast, the maximum root length and total root length were decreased in IS23143. Similarly, across the lines, drought stress decreased stomatal conductance (37%), transpiration rate (42%), photosynthetic rate (40%), photosystem II quantum yield (20%), photochemical quenching (44%), and total dry matter production (34%) than irrigated control. An increased transpiration rate was observed in IS23143 than IS13540 under irrigated and drought stress. In IS23143, the reduction in photosynthetic rate under drought may be a combination of stomatal and non-stomatal factors. However, in IS13540, the reduction is especially by the stomatal factors. It is evident that IS13540 is a drought-tolerant line, and tolerance is related to a deep prolific root system and reduced tran-spiration rate.

To investigate the effect of acidic nanoparticles on proton conductivity, permeability and fuel cell performance, a commercial Nafion® 117 membrane was impregnated with zirconium phosphates (ZrP) and sulfated zirconium (S-ZrO2) nanoparticles. The tensile test, water uptake, methanol crossover, Fourier-transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Thermal gravimetric analysis (TGA) and Scanning Electron Microscopy (SEM) were used to assess the ca-pacity of nanocomposite membrane to function in a fuel cell. The modified Nafion® membrane obtained the higher water uptake and a lower water content angle than the commercial Nafion® 117 membrane, indicating that it has a greater impact on conductivity. Under strain rates of 40, 30 and 20 mm/min, the nanocomposite membranes demonstrate more stable thermal deterioration and higher mechanical strength, which offers tremendous promise for fuel cell applications. When compared to 0.113 S/cm and 0.013 S/cm, respectively, of commercial Nafion® 117 and Nafion® ZrP membranes, the modified Nafion® membrane with ammonia sulphate acid had the highest proton conductivity of 7.891 S/cm. When tested using a direct single cell methanol fuel cell, it had the highest power density of 183 m. cm-2 which is better than commercial Nafion® 117 and Nafion® ZrP membranes.