Abstract: Amino acids are widely present as intermediates in marine nitrogen cycle. However, the information of amino acid distribution in deep-sea seawater, especially in abyss and hadal zone, is very limited. In the present study, we determined the concentrations of dissolved free amino acids (DFAA), dissolved combined amino acids (DCAA) and total hydrolysable amino acids (THAA) in the seawater from sea surface to hadal zone of the Yap Trench. Their occurrence, vertical variations and degradation behavior in the Yap Trench were investigated. The results showed that concentrations of ΣDFAA, ΣDCAA and ΣTHAA ranged from 0.09 to 1.78, 0.99 to 17.69 and 1.18 to 18.01 μmol/L, respectively, in the study area. In the seawater samples from the trench, Glycine (Gly) was the predominant DFAA, while the DCAA and THAA was dominated by threonine (Thr). Concentration of chlorophyll a (chl a) was not significantly correlated with any amino acids (DFAA, DCAA and THAA) in the euphotic layer. Mean concentrations for DFAA, DCAA and THAA in different water layers were in the order of: mesopelagic > euphotic > abyssal > bathyal. The concentrations of DCAA and THAA in sediment-seawater interface were higher than those from the euphotic to abyssal layer. Stations near the Yap Islands have the older organic matter (OM), while the organic matter in stations near the Yap Trench axis was relatively fresh above 1000-m depth. Degradation behavior of OM in the mesopelagic and abyssal layer are affected by transport of dissolved organic matter with water current. The organic matter in the sediment-seawater interface are older, especially on the west side of the trench. This is a survey of amino acids (DFAA, DCAA and THAA) in the Yap Trench, which provides information on the vertical variations and degradation behavior of amino acids from sea surface to hadal environment, and will be helpful to understand marine organic nitrogen cycle.

In urban areas like Chicago, daily life extends above ground level due to prevalence of high-rise buildings where residents and commuters live and work. This study examines the variation in fine particulate matter (PM2.5) concentrations across building stories. PM2.5 levels were measured using PurpleAir sensors, installed between April 8 and May 7, 2023, on floors one, four, six, and nine of an office building in Chicago. Additionally, data were collected from a public outdoor PurpleAir sensor on the fourteenth floor of a condominium located 800 meters away. Results show that outdoor PM2.5 concentrations peak at 14 meters height, then decline by 0.11 μg/m3 per meter elevation, especially noticeable from midnight to 8 AM under stable atmospheric conditions. Indoor PM2.5 concentrations increase steadily by 0.02 μg/m3 per meter elevation, particularly during peak work hours, likely caused by greater infiltration rates at higher floors. Both outdoor and indoor concentrations peak around noon. We find that indoor and outdoor PM2.5 are positively correlated, with indoor levels consistently remaining lower than outside levels. These findings align with previous research suggesting decreasing outdoor air pollution concentrations with increasing height. The study informs decision-making by community members and policymakers regarding air pollution exposure in urban settings.

Material identification based on R_value (transparency natural logarithm ratio of low-energy to high-energy) of line-scan dual-energy X-ray transmission (DE-XRT) has a good prospect for industrial application. Unfortunately, the DE-XRT signals before attenuation cannot be directly measured, whereas their precision is very important to R_value. Therefore, a context-based signal synthesis method which takes the filtered signals that remove high-frequency noises and retain low-frequency actual fluctuations as the reference value, and takes into account the vertical (forward/column) direction and horizontal (scanning/row) direction anisotropy of line-scan images was proposed. The vertical is a time series with continuity of signal trend; the horizontal is a spatial characteristic with the fluctuation synchronization within the same row signals. The special synthesis evaluations of curve synthesis difference and surface synthesis difference were also proposed. Experimental results show that the tow evaluations are both only about 0.0007, and it only takes 35 ms to complete the surface synthesis of 119×119 pixels on the CPU with 3.4 GHz main frequency. The presented method can achieve high signal synthesis precision and calculation real-time, so as to facilitate DE-XRT material identification. It can be extended to improve the precision of numerical synthesis in other line-scan uncomplete signals.

In this paper, dual-rotor counter-rotating (CR) configurations of vertical axis wind turbines (VAWT) are briefly inspected and divided into three types. This investigation was focused on one of these types – the CR-VAWT with co-axial rotors, in which two equal rotors are placed on the same shaft, displaced from each other along it and rotate in opposite directions. For this CR-VAWT with three-blade H-Darrieus rotors, the properties of the design in terms of aerodynamics, mechanical transmission and electric generator, as well as control system are analyzed. A new direct-driven dual-rotor (DR) permanent magnet synchronous generator (PMSG) was proposed, in which two built-in low-power PM electric machines have been added. They perform two functions – start-up and overclocking of the rotors to the angular velocity at which the lifting force of the blades is generated and stabilizing the CR-VAWT work as wind gusts act on the two rotors. Detailed in this paper is the evaluation of aerodynamic performance of the CR-VAWT via 3D computational fluid dynamics (CFD) simulations. The evaluation was conducted using the CONVERGE CFD software with the inclusion of the actuator line model for the rotor aerodynamics, which significantly reduces the computational effort. Obtained results show that both rotors, while they rotate in opposite directions, had a positive impact on each other: the power coefficients of the upper and lower rotors in the CR-VAWT increased by 5.5% and 13.3% respectively compared to the single-rotor VAWT at the optimal distance between the rotors of 0.3 from a rotor height.

To date, radiation adaptation response has been reported as a low-dose related phenomenon and has been associated with radiation hormesis. Well-known cancers are caused by non-radiation active reactants, in addition to radiation. A model of suppression for radiation-specific cancers was previously reported, but the model did not target radiation-nonspecific cancers. In this paper, we describe kinetic models of radiation-induced suppressors for general radiation non-specific cancers, estimating the dose that induces the maximum hormesis effect while satisfying the condition that the risk is approximately proportional to dose above 100 mSv. It was found that the radiation hormesis effect is maximal at about 20 mSv when the rate constant for generation is the same as the rate constant for decomposition. When the two rate constants are different, the dose at which the radiation hormesis effect is maximized depends on both rate constants, but the dose increases as the two rate constants approach each other, reaching a maximum of about 20 mSv. This conclusion may lead to the discovery of unknown cancer suppressors at low doses and the development of cancer suppression methods in the future.

Free-Living Amoebae (FLA) are widely distributed protozoa in both nature and artificial environments such as drinking water. Besides the ability of all FLA to transport various pathogenic microorganisms, certain species, Acanthamoeba spp. or Balamuthia mandrillaris, have intrinsic pathogenic abilities and cause severe cerebral infections. Previous work has shown an enrichment of FLA cysts in biofilm developed in upper levels of Drinking Water Storage Towers (DWST), suggesting that differences in densities of FLA cysts may play a role in their unequal distribution in the water column. To evaluate this hypothesis, a model of a water column was created for this study and used to analyze the vertical distribution of cysts of the FLA Acanthamoeba castellanii, Vermamoeba vermiformis and Balamuthia mandrillaris from 0 to 23 weeks. Interestingly, our data showed that the cysts of both A. castellanii and V. vermiformis were enriched in upper water levels during their aging. However, B. mandrillaris cysts were equally distributed in the water column during the entire study. These results showed that, besides the role of the water level variation in the DWST, some FLA cysts can become less dense during their aging, which contributes to their enrichment in upper water, and thus biofilm levels.

The foraging behavior of ruminating ungulates significantly impacts forest ecosystems due to their nutritional requirements. This study focuses on inter-specific comparisons of bark browsing (stripping) between Douglas fir (Pseudotsuga menziesii (Mirb.) Franco) and silver fir (Abies alba Mill.). Field measurements were conducted at the previously established research-demonstration site "Husárik" in the Javorníky Mountains, north-western Slovakia. We didn’t only measure the sizes of wounds on stems but also assessed the dimensions of unrecovered parts of wounds, subsequently calculating areas of recovered bark patches. Then, the total areas of wounds, recovered patches, and unrecovered parts were determined. Additionally, the percentages of wound areas, recovered areas, and unrecovered areas were expressed as their proportions to the total bark surface. Influencing factors such as the position of wounds along the vertical stem profile and stem diameter class were analyzed using two- and three-way ANOVA followed by Fisher's LSD test. The results demonstrate the susceptibility of both tree species to bark browsing by ruminating ungulates, primarily red deer (Cervus elaphus L.) in our study site. Douglas fir exhibited slightly less intense browsing compared to silver fir, while silver fir had a slightly higher recovery rate. Specifically, 17.0% of the bark surface in Douglas fir and 21.5% in silver fir were browsed. The proportions of recovered areas on wounds were 62.5% and 69.6% in Douglas fir and silver fir, respectively. Regarding the vertical stem profile, the most intense browsing occurred at a height of 101-125 cm from the ground level, with rates of 40.7% in Douglas fir and 47.0% in silver fir. Browsing intensity showed negligible variation among diameter classes, which were classified as up to 35 mm, 35-50 mm, and over 50 mm. Our findings suggest that, as an introduced species, Douglas fir is not any suitable substitute for other commercially significant tree species in European countries where ruminating ungulates are overabundant.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

In this paper presents analytical findings regarding the influence of gravity disturbance on INS. A data from the high-precision gravity model, EGM2008, we introduce a novel real-time gravity disturbance compensation approach for INS. This method estimates gravity disturbances along paths for platforms on both land and water, utilizing the Multi-Layer Perceptron (MLP) technique. To estimate these gravity disturbances, we developed four distinct MLP models and compared their training results using Half-Mean Square Error (half-MSE) and Root Mean Square Error (RMSE). This comparative analysis allowed us to identify the MLP model that exhibited the best performance. In order to validate the proposed gravity compensation method, field test was conducted using a test vehicle. The results of this field test unequivocally demonstrated the effectiveness of our approach in enhancing positioning accuracy. Over the course of a 2-hour field experiment, it was evident that employing the proposed gravity compensation method improved positioning accuracy by a notable 24%.

Introduction The placement of implants is often hindered by a severely atrophic mandibular edentulous ridge. A sufficient volume of bone graft is crucial for successful implant restoration. The required bone graft volume directly correlates with the deficiency present in the edentulous ridge. If the residual crestal bone height is so low that the distance between the crestal ridge and the inferior alveolar nerve is less than 2 mm, a significant bone augmentation procedure is necessary. This procedure must ensure the implants are surrounded by a sufficient margin of bone, aiming for a final height of more than 8 mm and a width of more than 7 mm. Achieving primary closure with adequate soft tissue is vital for the success of the bone graft procedure. The key to successful bone grafting lies in the effective management of the soft tissue covering. Case Report This case report details the treatment of a patient with severely atrophic edentulous ridges on both sides, addressed using Self Inflating Tissue Expanders (SITEs) to facilitate bone grafting and implant placement. Following soft tissue expansion, bone grafting and implant placement were successfully performed. The implants supported a fixed restoration, which remained stable and complication-free over a seven-year observation period. Conclusion The SITE (Self-Inflating Tissue Expander) proved effective in obtaining a substantial amount of bone graft needed for implant installation. A seven-year follow-up confirmed the implants were well-functioning with stable bone support, healthy soft tissue coverage, and adequate vestibular depth.

Previous studies have demonstrated that cold pools play a pivotal role in the initiation and organization of convection, yet their influence on the evolution of GFs remains inadequately understood. A destructive wind event associated with a rearward gust front (RGF, 8 grade gale appeared after passing GF) and a prior gust front (PGF, 10 grade gale appeared before passing GF) over the north coast of China on 10 June 2016 was analyzed. Using multiple observation data as well as the four-dimensional Variational Doppler Radar Data Assimilation System (VDRAS), we found that the intensity of the GFs increased with increasing cold pool strength, depth and propagation speed. Two schematic models were proposed to explain the discrepancy between GFs and associated cold pools. The depth and intensity of the cold pool in RGF are found to be relatively shallower and weaker, leading to a correspondingly reduced strength in both outflow and convergence. In contrast, the enhanced vertical shear and boundary northeaster inflow of PGF generate intensified and more organized downdrafts, resulting in a deeper cold pool, robust outflow, and convergence. These findings offer novel insights into the diversity of GFs and associated cold pools.

Incremental control strategies provide undeniable advantages for controlling Uncrewed Aerial Vehicles (UAVs) due to their reduced model dependency and accurate tracking capacities. This is of particular relevance for hybrid UAVs, specially for tail-sitters, which perform complex manoeuvres when transitioning to and from aerodynamic flight. This paper summarizes the research undertaken in the application of the Incremental Nonlinear Dynamics Inversion (INDI) and Incremental Backstepping (IBKS) to a small tail-sitter UAV. After the application of these control strategies in a simulated scenario, the implementation in a Micro-Controller Unit was validated in a Hardware-in-the-Loop scenario. Following such validation, indoor experimental trials were undertaken in order to evaluate the capacity of these controllers to stabilize and control the real aircraft. The stabilization in the flight trials was successfully implemented and allow to conclude that both INDI and IBKS are control strategies suited to control a tail-sitter in vertical flight, providing accurate tracking capabilities under smooth actuation. Furthermore, it was found that the IBKS is significantly more computationally demanding than the INDI, although having a global proof of stability that is of interest in aircraft control.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

To reduce the cost of small wind turbines, a prototype of a butterfly wind turbine (6.92 m in diameter), a small vertical-axis type, was developed with many parts made of extruded aluminum suitable for mass production. An over-speed control system with movable arms that operated using centrifugal and aerodynamic forces was installed for further cost reduction. Introducing this mechanism eliminates the need for large active brakes and expands the operating wind speed range of the wind turbine. However, although the mechanism involving the use of only bearings is simple, the violent movement of the movable arms can be a challenge. To address this in the present study, dampers were introduced on the movable arm rotation axes to improve the movement of the movable arms. To predict the behavior of a movable arm and the performance of the wind turbine with the mechanism, a simulation method was developed based on the blade element momentum theory and the equation of motion of the movable arm system. Comparison of experiments and predictions with and without dampers demonstrated qualitative agreement. In the case with dampers, measurements confirmed the predicted increase in the rotor rotational speed when the shorter ailerons installed perpendicularly to the movable arms were used to achieve the inclination. The movable arm system with dampers is expected to be a useful device for vertical-axis wind turbines that are difficult to control.

Vertical-axis wind turbines (VAWTs) are receiving more and more attention as they involve simple design, cope better with turbulence and are insensitive to wind direction which has a huge impact on the cost since the yaw mechanism is not needed. However, VAWTs still suffer from low conversion efficiency. As a results tremendous efforts are exerted to improve its efficiency which mainly focus on two methods regardless of whether the study is a CFD simulation or a field test or lab test experiment. An active approach which involves the modification of the rotor itself such as the blade design, angle, trailing and leading edges, inner blades, chord thickness, contra-rotating rotor, etc. While the second approach involves passive techniques where the flow is directed to optimally face the downwind rotor by mounting a guiding vane such as a diffuser or other shapes at the upwind position of the rotor. Among all techniques undertaken, the CRWT rotor technique seems to be the most effective with an output even comparable to that of Horizontal Axis Wind Turbines (HAWT), while the Savonius rotor received more attention compared to other designs of VAWTs. Apart from technological issues, it was also suggested that geographical issues such as proper site siting of the wind turbine rotor at a particular location where a uniform flow could be guaranteed is of paramount importance to ensure an effective conversion capacity of wind turbines.

Sea level rise due to global warming is a continuing and, disappointingly, accelerating process, which has already affected and will further impact coastal lowlands and the social and economic activities in these areas. Delos Island, situated in the middle of the Cyclades in the Aegean Sea, was considered the most sacred of all islands in ancient Greek culture and a trading hub for the entire eastern Mediterranean. Uninhabited since the 7th century AD, and consistently the focus of research and touristic attention, the island is designated as an archaeological site and inscribed on the Unesco World Heritage List. Previous studies on the relative sea level (rsl) changes suggest a steadily rsl rise during the last 6,300 years, starting from a sea level at -4.80±0.20m in the Late Neolithic. The seafront of the ancient city of Delos is subject to the effects of the rsl rise, which have caused significant coastline retreat and exposure to the northerly winds and waves, whereas parts of the coastal lowland where the remains of the ancient city lie are inundated, forming extended wetlands. The future impacts of rsl rise on the seafront of ancient Delos are illustrated on very high-resolution digital surface models, evaluating both the flooding risk under different climatic projections, as provided by the IPCC AR6 report, and the ongoing land subsidence, as recorded by GNSS data. An rsl rise ranging from 87cm (SSP1-2.6 scenario) to 148cm (SSP5-8.5 scenario) is anticipated by 2150, requiring both resilience strategies and adaptation solutions as well as mitigation policies to cope with the effects of climate change.

In response to the burgeoning global demand for premium agricultural products, particularly within the competitive nut market, this paper introduces an innovative methodology aimed at enhancing the grading process for almonds and their shells. Leveraging state-of-the-art Deep Convolutional Neural Networks (CNNs), specifically the AlmondNet-20 architecture, our study achieves exceptional accuracy exceeding 99%, facilitated by the utilization of a 20-layer CNN model. To bolster robustness in differentiating between almonds and shells, data augmentation techniques are employed, ensuring the reliability and accuracy of our classification system. Our model, meticulously trained over 1000 epochs, demonstrates remarkable performance, boasting an accuracy rate of 99% alongside a minimal loss function of 0.0567. Rigorous evaluation through test datasets further validates the efficacy of our approach, revealing impeccable precision, recall, and F1-score metrics for almond detection. Beyond its technical prowess, this advanced classification system offers tangible benefits to both industry experts and non-specialists alike, ensuring globally reliable almond classification. The application of deep learning algorithms, as showcased in our study, not only enhances grading accuracy but also presents opportunities for product patents, thereby contributing to the economic value of our nation. Through the adoption of cutting-edge technologies such as the AlmondNet-20 model, we pave the way for future advancements in agricultural product classification, ultimately enriching global trade and economic prosperity.