Germanium (Ge) nanostrip is embedded in polymer and studied as a waveguide. Measurement reveals that this new type of semiconductor/polymer heterogeneous waveguide exhibits strong absorption for the TE mode from 1500 nm to 2004 nm, while the propagation loss for the TM mode declines from 20.56 dB/cm at 1500 nm to 4.89 dB/cm at 2004 nm. The transmission characteristics serves as an essential tool to verify the optical parameters (n-κ) of the thin strips, addressing to the ambiguity raised by spectroscopic ellipsometry regarding highly absorbing materials. Furthermore, the observed strong absorption for the TE mode at 2004 nm is well beyond the cut-off wavelength of the crystalline bulk Ge (~1850 nm at room temperature). This redshift is modeled to manifest the narrowing of the Tauc-fitted bandgap due to the grain order effect in the amorphous Ge layer. The accurate measurement of the nanometer-scale light-absorbing strips in a waveguide form is a crucial step toward the accurate design of integrated photonic devices that utilize such components.

The integration of renewable energy and hybrid energy storage system (HESS) into electrified railways to build electric railway smart microgrid system (ERSMS) is beneficial for reducing fossil fuel consumption and minimizing energy waste. However, the fluctuations of renewable energy generation and traction load challenge the energy management effectiveness for such a complex system. In this work, an energy management strategy is proposed which firstly decomposes the renewable energy into low-frequency and high-frequency components by an integrated empirical mode decomposition (IEMD). Then, a two-stage energy distribution approach is utilized to appropriately distribute the energy flow among the ERSMS. Finally, the feasibility and effectiveness of the proposed solution are validated through case study.

The paper shows that it is possible to obtain reliable information on the dependence of radial distribution of longitudinal birefringence in glass cylindrical elements with radial distribution of refractive index (GRIN lenses) on the basis of transverse polarization tomography data of residual stresses. This does not require complicated procedures of sample preparation, as is necessary in the case of longitudinal translucency measurements. The approach developed was verified in the experiments with a set of different GRIN lenses formed with ion exchange technique, and the closeness of the data obtained from transversal and conventional longitudinal transmission measurements was demonstrated.

One of the future challenges of increasing the harnessed solar power is efficiency using of CubeSat sides. One of the approaches is using integrated antenna systems with solar panels or payloads. This study proposes a new approach to the use of integrated antenna systems in remote sensing missions. In this approach, due to the integration of antenna system with payload (in our case, with camera), it is possible to achieve a significant increase in the power generation. Calculations are carried out for cases when the antenna system are integrated with the optical system (α = 0°), which implies that they use one plane, in the second case they are spaced at an angle of α = 90° and in the third case when they are directed to opposite sides (α =180°). In the case of α = 0°, where the camera and antenna module are aligned co-axially, there is no energy expenditure for CubeSat orientation. However, in the other two cases, energy is required for rotation and maintenance of the specified orientation throughout the entire duration of the satellite's flight over the ground station, amounting to 111.99 mW when α = 90° and 44.33 mW when α = 180°.

Over the last ten years, the integrated pond aquaculture (IPA) has been developing rapidly as a new aquaculture mode, and mechanical power oxygenator is a common oxygenation device in this aquaculture mode. However, with the gradual expansion of the application range of this aquaculture mode, the problems of low efficiency, poor oxygenation uniformity, and low applicability of mechanical power oxygenators, which can produce water reflux and suction pollution accumulation, have gradually emerged. Therefore, we designed a new type of push-water aerator device (NPWAD) applicable to the integrated recirculating water aquaculture mode of ponds. Mainly, the specific parameters of the key components were clarified through the selection calculation and structural design, and the experiments were carried out in the self-constructed pond integrated aquaculture system at the experimental base. The experiments were carried out on the water in the tank for grass carp culture, and the oxygenation and water pushing effects of the type of push-water aerator device under 15 groups of different operating parameters were carried out by using multiple types of high-precision water quality monitoring sensors, with the rotational speed of the device, the operating time (0-30 min) and the height of the water (0.5-1.5 m) as the independent variables, and the oxygenation amount R, the oxygenation power efficiency E_s and the surface layer of the water as the evaluation indexes, average flow velocity V_f were used as its evaluation indexes of oxygenation and water pushing. The results show that the optimal parameters of the NPWAD are impeller water lifting component speed n_1=1000r/min, small-hole aeration component speed n_2=2280r/min. At this time, the average oxygen increase of this device is R=1.96mg/L, the average oxygenation power efficiency is E_s=3.8 kg·(h·kW)-1, the DO uniformity of the water M_1=95.3%, and the average flow velocity V_f=190.8mm/s, which can effectively promote the water directional flow and achieve the water circulation and layer exchange, and it is in line with the preferred swimming speed of grass carp at various growth stages. The new type of push-water aerator device is able to enhance the DO concentration of the water faster, but also to achieve the purpose of promoting the directional flow of the water and renewing the water in the tank, as well as in a short period of time to improve the uniformity of the DO of the water faster, for the improvement of the pond aquaculture production efficiency has practical significance.

We simulated the glass-blowing process to model a shell resonator, which is a key component in MRIG (Micro Rate Integrating Gyroscope), using the finite elements method to solve a non-isothermal problem. We also calculated the mechanical characteristics of the modeled resonator, including effective mass, eigenfrequencies, angular gain, and energy loss, to predict the resonator's performance as a gyroscope. One key aspect we addressed is the bending of the resonator's rim toward the stem during glass-blowing process. This phenomenon occurs due to increased heat loss at the mold's edge and reduced heat flux at the side of the Gaussian heat source. To mitigate rim bending and the subsequent reduction in capacitance between the rim and 3D electrodes, which can degrade performance in micro glass-blown shell resonators for gyroscopes, we propose two potential mold solutions. The first is using a short-stem mold, which requires extensive polishing to eliminate the bent rim. The second solution is using a mold with a suitable chamfer at the edge, resulting in a straight rim. To quantitatively compare resonators created by these two types of molds, we calculated the noise factor for predicting its gyroscope performance. From these calculations, we find out that using the chamfered mold enables us to increase in the resonator's effective mass, eigenfrequency, angular gain, and quality factor, consequently reducing the noise factor compared to using the short-stem mold. This simulation process will assist us in getting insight into understanding a shell resonator as a gyroscope, designing a mold and determining experimental conditions.

The use of biostimulants consisting of plant growth promoting rhizobacteria (PGPR) is rapidly expanding in horticulture in recent years. In the current study, a novel mix of six Bacillus sp. strains was tested as a PGPR biostimulant in two experiments with zucchini squash (Cucurbita pepo L.) cultivated in the greenhouse soil and in an open field, respectively. In both experiments, seeds of the local landrace ‘Kompokolokytho’ and the commercial hybrid ‘ARO-800’ were either inoculated or non-inoculated with the PGPR biostimulant. The application of the six Bacillus sp. strains increased both the vegetative growth and the yield of zucchini squash, and these effects were associated with significantly higher shoot phosphorus levels in both experiments and both genotypes. Furthermore, at the end of the cultivation, the colony forming units of Bacillus sp. were appreciably higher in plants originating from inoculated compared to non-inoculated seeds, indicating that the tested mix of Bacillus sp can be successfully applied through seed inoculation. ‘ARO-800’ produced more vegetative and fruit biomass than ‘kompokolokytho’ under greenhouse cropping conditions, while in the open-field crop both genotypes performed equally, presumably because the local landrace is traditionally grown in open fields, and thus it is not well adapted to greenhouse cropping.

Integrated cultivation strategies can significantly improve rice yield. However, it is unclear how integrated cultivation practices improve soil microbial diversity and its related mechanism in rice field. Therefore, four integrated cultivation practices i.e., no N application (N0), local farmers’ practice (FP), high-yield and high-efficiency practice (HYEY), and super-high-yield cultivation practice, impacts on soil properties and structure composition of microbial community were explored. Compared with N0, SHY treatment, significantly increased soil alkaline nitrogen and organic matter contents. HYHE and SHY treatments significantly altered soil fungal community and Alpha diversity. Based on Venn diagram analysis, the composition of bacterial communities under all treatments was similar, but with different compositions of fungal communities. Cluster analysis indicates that the Proteobacteria was the absolute dominant group of bacterial communities, and Chloroflexi, Bacteroidetes, and Acidobacteria were the dominant group. Different cultivation methods also led to changes in the main factors affecting soil bacteria and fungi composition. Available potassium and organic matter were the main environmental factors that affected bacteria, with the strong of available potassium on the soil. To sum up, SHY and HYEY were beneficial management options in terms of improved soil fertility Alpha diversity of the soil bacterial community respectively.

One way to reduce the negative impact of human activity on the natural environment is to use natural, easily available and relatively cheap to produce compounds in industrial processes. One such compound is naturally occurring calcium carbonate (CaCO3). This compound has adsorption properties so that it can be an alternative to commonly used adsorbents. The aim of this work is to determine the possibility of using CaCO3 to remove pharmaceutical substances such as sulfadiazine and tetracycline from water. The CaCO3 used in this work was synthesised using our own method, which allows the production of CaCO3 particles with nanometric size. In the conducted research, calcium carbonate was used in the form of a suspension in purified solutions and as an inorganic filling of the developed membranes. The mass of pharmaceutical substances removed from their aqueous solutions was determined in the tests carried out. Based on the results obtained, it can be concluded that CaCO3 has the ability to adsorb both tetracycline and sulfadiazine. In suspension tests, the mass of the removed substances per unit mass of adsorbent was 1.52 mg/g and 6.85 mg/g, respectively. In turn, in the case of the process using the developed membranes, the mass of the removed substances per unit mass of adsorbent was 232 mg/m2 and 524 mg/g, which is a several times greater increase in the mass of the removed substance compared to the process using an unmodified membrane.

This paper proposes an active-reactive power collaborative scheduling model with cluster division for the flexible distributed energy resources (DERs) of smart building system to resolve the high complexity of centralized optimal scheduling of massive dispersed DERs in the distribution network. Specifically, the optimization objective of each cluster is to minimize the operational cost, the power loss cost, and penalty cost for the flexibility deficiency, and the second-order cone-based branch flow method is utilized to convert the power flow equations into the linearized cone constraints, reducing the nonlinearity and heavy computation burden of the scheduling model. Customized virtual battery models for the building-integrated flexible DERs are developed to aggregate the power characteristics of flexible resources while quantifying their regulation capacities with time-shifting power and energy boundaries. Moreover, a cluster division algorithm considering the module degree index based on the electrical distance and flexible balance contribution index is formulated for cluster division to achieve the information exchange and energy interaction in the distribution network with high proportion of building-integrated flexible DERs. Comparative studies have demonstrated the superior performance of the proposed methodology on the economic merits and voltage regulation.

Species richness is a widely used measure for assessing the diversity of a particular area. However, observed richness often underestimates the true richness due to resource limitations, particularly in the small-sized sample or highly heterogeneous assemblage. Estimating species richness in a large-scale region typically involves an integrated data set consisting of subsamples collected independently from different subregions. However, the pooled sample of integrated data is no longer a random sample from the entire region, and the use of different sampling schemes results in variations in data formats. Consequently, employing a single sampling distribution to model the pooled sample becomes impractical, rendering existing richness estimators inadequate. This study theoretically explains the applicability of Chao's lower bound estimators in estimating species richness for large-scale areas using the pooled sample. Additionally, a new nonparametric estimator is introduced, which adjusts the bias of Chao's lower bound estimator by leveraging the Good-Turing frequency formula. This proposed estimator only utilizes the pooled sample's singleton, doubleton, and tripleton richness. Simulated data sets across various models are employed to demonstrate the statistical performance of the estimator, showcasing its ability to reduce bias and provide accurate 95% confidence intervals. Real data sets are also utilized to illustrate the practical application of the proposed approach.

The hybridization of conventional thermal power plants by incorporation of renewable energy systems has witnessed widespread adoption in recent years. This trend aims not only to mitigate carbon emissions but also to enhance the overall efficiency and performance of these power generation facilities. However, calculating the performance of such intricate systems using fundamental thermodynamic equations proves to be both laborious and time-intensive. Nevertheless, possessing accurate and real-time insights into their performance is of utmost significance to ensure optimal plant operation, facilitate decision-making, and streamline power production planning. In this paper, we delve into the application of machine learning techniques, particularly hybrid methodologies, to predict the performance of power plants. Specifically, we employ three approaches: the Adaptive Neuro-Fuzzy Inference System (ANFIS), the ANFIS optimized via Particle Swarm Optimization (ANFIS-PSO), and the ANFIS optimized through Genetic Algorithm (ANFIS-GA). These techniques are alternatively applied to a complex hybrid thermal power plant, namely an Integrated Solar Combined Cycle Power Plant (ISCCPP). This ISCCPP comprises a steam turbine section, a gas turbine section, and a concentrated solar power system utilizing troughs as collectors. The energy transfer fluid, in conjunction with exhaust from the gas turbine section, heats water within a vessel or steam generator, producing steam to propel the steam turbine's rotor. Electricity generation is facilitated by both gas and steam turbines, which are coupled to a generator. The findings of this study underscore the accuracy and appropriateness of ANFIS-based models in evaluating and predicting the performance of intricate hybrid power plants. The ANFIS model exhibited an impressive overall coefficient of correlation of 0.9991. Notably, the integration of evolutionary algorithms (PSO and GA) into the ANFIS framework elevated model performance, yielding correlation coefficients of 0.9994 for ANFIS-PSO and 0.9997 for ANFIS-GA. It is noteworthy that ANFIS-GA demonstrated superior predictive capability. The modeling framework developed in this research offers valuable support to designers, energy managers, and decision-makers. It provides a robust and dependable tool to assess the performance of hybrid thermal power plants, which are poised for a global surge in numbers amid the ongoing energy transition.

Building energy consumption is the main urban energy consumption component, which mainly serves people-centered work and living energy demands. Based on the physical requirements of humans in urban buildings and to determine the comfortable body temperature in each season, this paper establishes a sizing optimization model of building-type integrated energy systems (IES), where the cooling and heating loads required to maintain indoor somatosensory body comfortable temperature are calculated. Depending on the external energy price, internal power balance and other constraints, the model develops an optimal sizing and capacity panning method of energy conversion and storage unit in a building-type IES with PV generation. The operating principle is described as follows: the PV generation is fully consumed, a gas engine satisfies the electric and thermal base load requirements, while the power system and a heat pump supply the remaining loads. The gas price, peak-valley electricity price gap and heat-topower ratio of gas engines are considered as important factors for the overall techno-economic analysis. The developed method is applied to optimize the economic performance of building-type IES and verified by practical examples. The results show that using the complementary characteristics of different energy conversion units is important to the overall IES cost.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Abstract: With the continuous integration of various energy systems and the reform of energy trading marketization, the traditional power demand response can no longer meet the needs of multi-energy coupling. For the joint response problem of multi-energy, this paper proposes a comprehensive demand response optimization incentive model considering the user response characteristics, with the complete energy service providers and multiple users as the participants of the comprehensive demand response, to solve the response strategy for the optimal goal of all parties. The implementation architecture of integrated demand response and the electrothermal energy hub model is introduced first. Secondly, the integrated demand response collaborative optimization strategy of the integrated energy service providers and users is established, and the existence and uniqueness of the optimal solution are proved. Finally, the example analysis demonstrates that the proposed strategy can reduce the integrated energy service providers' response cost and user dissatisfaction under multiple scenarios.

The effects of soluble silicon fertilization on monocots and dicots have been widely studied. However, little is known regarding its effects on protecting epiphytes against insect and fungal pests. The efficacy of silicon fertilizer to reduce damage by thrip pest complexes, namely: Thrips palmi Karny, Frankliniella occidentalis Pergande, Chaetanaphothrips orchidii Moulton, and Chaetanaphothrips signipennis Bagnall (Thysanoptera: Thripidae), and fungal pathogens: Botrytis cinerea Persoon (Helotiales: Sclerotiniaceae) and Fusarium spp. Link (Hypocreales: Nectriaceae) was examined during a nine-month greenhouse trial in Hawaii. The trial assessed yield, quality, and pest damage across three common varieties of dendrobiums. All replicates received additional soluble silicon fertilizer applications alternating weekly between soil drench and foliar (50 mg Si/plant) applications. Yield, quality, and spray length, pest damage, plant vigor, SPAD, and leaf temperature were measured. Data were analyzed using a generalized linear model (glm) with repeated measures followed by post-hoc pair-wise comparisons in R, version 4.3.1. Treatment effects were significant at P

Today's city needs more than ever methodological devices that ensure a specific urbanism, in keeping with the complexity of relationships that occur in the urban space. Networks or systems of diverse nature must be activated to achieve a certain success of the city, even more so in its fragile central fabrics. The study is focused on the historic neighborhoods of the city of Jaén (Spain), which have a high vulnerability index. The aim is to establish a strategy to revitalize their urban and social capital and improve their articulation with the rest of the urban and territorial structure. A methodological proposal for the analysis of vulnerability factors and an urban and cartographic analysis of the public space is addressed through an interweaving of a triple network: environmental, social, and urban. For this purpose, the configuration of this overlapping network of analysis and formulation of criteria is presented, which considers the urban multiplicity and promotes new dynamics for the integrated urban regeneration of the area and for the activation of public and collective urban spaces.

In order to achieve its carbon peak and neutrality targets, a high proportion of distributed power sources are connected to the distribution network in China, which greatly increases the risk of distribution network operation. Aiming at the above problems, this paper proposes an active distribution network risk planning model based on multi-source data from carbon capture and power internet of things, and conducts exceeding testing of distribution network based on the stochastic load flow algorithm with semi-invariant and level expansion, calculates the semi-invariant of each order of node state vectors and branch current vectors, and then utilizes the Gram-Charlier level expansion to obtain the exceeding probability density function and probability distribution function of the node voltages and line powers of the distribution network. The probability density function and probability distribution function of the exceeding are obtained using the Gram-Charlier series expansion. Combined with multi-source data, the active distribution network with integrated energy system considering carbon capture is modeled. According to the risk scenario of the distribution network, the nonconvex constraints in the model are simplified by the second-order cone relaxation, and the optimal planning scheme of the distribution network is solved by combining the gurobi solver with the risk index as the first-level objective and the economic benefit as the second-level objective. The simulation results of a coupled network consisting of a 39-node distribution network and an 11-node transportation network verify the effectiveness of the proposed model.

International basins are divided into sub-basins that are managed at the national and local levels, within the territory of each country, before reaching the level of international concern. The management of international basins could be developed using an integrated water management, based on multi-level governance model in which many actors are involved, from local to international scale. However, in the La Plata River Basin this model is not working, even with international agreements such as the La Plata Basin Treaty, which was signed in 1969. The understanding of political interests behind the law helps to explain its inefficiency. Therefore, considering the lack of a systemic view in an international watershed, it could be possible to have accumulating effects caused by the transformations of watercourses in the sub-basins. Then, the 2014 water crisis in the State of São Paulo, Brazil, is an example of the possible consequences arising from the lack of an integrated water management in the La Plata River Basin. Finally, this article demonstrates that the only way to have water resources utilization efficiency in an international basin is considering it as an integrated ecosystem, in order that any local problem may affect the whole basin.

To address the problems of wind abandonment in the regional integrated energy system (RIES), which occurs when cogeneration unit operates in a heat-determined electricity operation mode, and the low efficiency of the energy storage system in a low-temperature environment, we propose an optimal scheduling method for RIES based on fine energy storage and wind power dissipation. First, a fine energy storage model is established on the source side and the conditional value at risk(CvaR) theory is used to quantify the uncertainty of wind power; then a combined heat and power demand response mechanism is introduced on the load side to reduce the peak-to-valley difference between heat and power loads, and to promote the consumption of wind power. Finally, with the objective of minimizing the total cost of RIES optimal dispatch, the example is solved on the MATLAB platform. The simulation results show that compared with the traditional model, the proposed model is not only more adaptable to the low-temperature environment, but also can effectively improve the system economy and wind power consumption.

Efficient heat management and control in optical devices, facilitated by advanced thermo-optic materials, is critical for many applications such as photovoltaics, thermal emitters, mode-locked lasers, and optical switches. Here, we investigate the thermo-optic properties of 2D graphene oxide (GO) films by precisely integrating them onto microring resonators (MRRs) with control over the film thicknesses and lengths. We characterize the refractive index, extinction coefficient, thermo-optic coefficient, and thermal conductivity of for the GO films with different layer numbers and degrees of reduction, including reversible reduction and enhanced optical bistability induced by photo-thermal effects. Experimental results show that the thermo-optic properties of 2D GO films vary widely with the degree of reduction, with significant polarization anisotropy, enabling efficient polarization sensitive devices. The versatile thermo-optic response of 2D GO substantially expands the scope of functionalities and devices that can be engineered, making it promising for a diverse range of thermo-optic applications.

On February 28th, 2023, Spanish Royal Decree 150/2023 as published, approving the plans for the management of the maritime space of the five Spanish marine demarcations. This Royal Decree Law inaugurates the Planning of the Maritime Space in Spain. Terrestrial Space Planning is very advanced, both in the legislation and in the instruments that are enabled to organize this space, from the national scale to the municipal scale, passing through the regional, provincial, and supra-municipal scales. Naturally, both Planning must converge and thus speak of an Integrated Space Planning. In some of the countries that we can take as global references, this convergence in the form of integration is taking place. On the other hand, and within the context of climate change, coastal cities will be the most affected, both by the potential rise in sea level and by the increasingly continuous and greater extreme events. Integrated Space Planning is postulated as the most effective tool to carry out adequate territorial and urban planning of our coastal cities, as well as to analyse the influence and possible corrective measures to apply against the effects produced by climate change.

Carbon dioxide capture and storage (CCS) is a necessary requirement for high-emitting CO2 industries to significantly reduce volumes of greenhouse gases released to the atmosphere and mitigate the climate change. Geological CO2 storage into depleted oil and gas fields is the fastest and most accessible option for CCS deployment allowing for re-purposing of existing infrastructure and utilizing the significant knowledge about the subsurface acquired during the field production operations. Location of such depleted fields in neighbourhood of high-emitting CO2 industries is additional advantage available for matured on-shore Europe fields. Considering these advantages, the oil and gas operators are now evaluating different possibilities for CO2 sequestration projects for the fields approaching end of production. This article describes an integrated approach to reservoir simulations focused on evaluating CO2 injection pilot at one of such matured fields operated by MND and located in the Czech Republic. The potential CO2 injection site in focus is a naturally fractured carbonate reservoir. This oil-bearing formation has a gas cap at the top and a limited aquifer at the bottom of the reservoir and was produced mainly by pressure depletion with quite limited pressure support from water injection. The article summarizes results of efforts taken by the multi-disciplinary team to develop and apply an integrated approach to reservoir simulation started from geological modelling of the naturally fractured reservoir and integrating results of laboratory studies and their interpretation (geomechanical and geochemistry laboratory experiments) and dynamic field data analysis (pressure transient analysis including time-lapse) into the history matching of the reservoir model and simulations of pilot CO2 injection. Attention is given to evaluating and modelling stress-sensitive fracture properties and safe injection envelope preventing induced fracturing as well as impact of potential salt precipitation in the near wellbore area. These effects are considered in the context of pilot CO2 injection and addressed in reservoir simulations of the injection scenarios. Single porosity and permeability reservoir simulations with dominating fracture flow and black-oil formulation with CO2 simulated as a solvent were used in this study and arguments for such choice of the simulation approach for the site in focus are shortly discussed. The reservoir simulations have indicated larger site injection capacity than required for the pilot injection and allowed to evaluate CO2 migration pathway within the reservoir. The application of the approach to the site in focus has also revealed large uncertainties, related to fracture description and geomechanical evaluations, resulted in an uncertain safe injection envelope. These uncertainties should be addressed in further studies in preparation to the pilot. The article concludes with an overview of the outcomes of the integrated approach and its application to the field in focus including discussion of issues and uncertainties revealed.

Household waste is the primary source of environmental pollution due to global population growth compared to other sources of waste. This research aims to develop a smart and integrated household waste management system framework. The resulting framework not only focuses on dimensions of information technology but also links it with other integrated dimensions. This research attempts to conduct a Systematic Literature Review (SLR) using the Preferred Reporting Items for Systematic Review and Meta-analysis (PRISMA) protocol to produce a smart and integrated household waste management framework. The framework's design is carried out by identifying the type of household waste management process based on the Integrated Sustainable Waste Management (ISWM) framework, dimensions that support smart household waste management, and stakeholders involved. The SLR results, namely dimensions and subdimensions that support the framework of a smart and integrated household waste management system, were validated by a resource person from the Indonesian Ministry of Environment and Forestry. The smart and integrated household waste management framework that has been developed in this research contains five main dimensions: Information Technology, Operational Infrastructure, Governance, Economy, and Social-culture. This framework also addresses stakeholder engagement to support smart household waste management systems and identifies waste management processes based on the ISWM framework. This research uses the PRISMA technique to provide a framework for smart and integrated household waste management systems in the initial stage. The proposed framework has been validated and can be further developed as a smart and integrated household waste management system. This research also contributes to the involvement of various dimensions identified to deal with waste problems.