The shear factor of ore drawing is one of the important factors affecting the formation of underground debris flow, and it has an important contribution to the formation of underground debris flow. The purpose of this paper is to study the effect of mining shear factor on underground debris flow in natural caving method. Based on the research background of the underground debris flow in Plan copper mine, this paper analyzes the characteristics of the slurry material structure of the underground debris flow, the influence of drawing shear factor on formation mechanism of underground debris flow is analyzed. The results show that the slurry of the underground debris flow in Plan mine is not only a pseudoplastic fluid but also a thixotropic fluid. It is indicated that once there is shearing force in drawing, it will deform, and its viscosity will decrease with the increase of shear rate and time. It is considered that the shear force produced by the flow of ore particles first produces shear action on the paste in the shear boundary region of ore drawing, it is reduced in viscosity and increased in fluidity, so that its “Activation” and then become a flowable paste, along with the bulk ore flow through the mouth. The continuous ore drawing process will continuously shear the new moraine slurry in the ore drawing channel and continuously “Activate” the moraine slurry in the ore drawing channel, finally, a certain scale and destructive down-hole debris flow accident. This paper is the first to study the effect of ore drawing shear factor on the formation mechanism of underground debris flow. It not only broadens the research field of debris flow, but also fills up the deficiency of systematic research on underground debris flow, and provides theoretical guidance for the prevention and control of underground debris flow.

While texturing of workpiece surfaces to promote lubrication in metal forming has been applied for several decades tool surface texturing is rather new. In the present paper tool texturing is studied as a method to prevent galling. Adopting a strip reduction test longitudinal pocket geometries oriented perpendicular to the sliding direction, with shallow pocket depth, small pocket angle to the workpiece surface and varying distance between pockets are investigated. The experiments reveal that the distance between pockets should be larger than the pocket width thereby creating a topography similar to flat table mountains to avoid mechanical interlocking in the valleys; otherwise an increase in drawing load and pick-up on the tools is observed. The textured tool surface lowers friction and improves lubrication performance provided that the distance between pockets is 2-4 times larger than the pocket width. Larger drawing speed facilitates escape of the entrapped lubricant in the pockets. Testing with low to medium viscosity oils leads to a low sheet roughness on the plateaus but also local workpiece material pick-up on the tool plateaus. Large lubricant viscosity results in higher sheet plateau roughness but also prevents pick-up and galling.

Microstructured optical fibres (MOFs) are a new type of optical fibres that possess a wide range of optical properties and many advantages over common optical fibres. Those are provided by unique structures defined by a pattern of periodic or quasi-periodic arrangement of air holes that run through the fibre length. In recent years, MOFs have opened up new possibilities in the field of optics and photonics, enabling the development of advanced devices and novel optical systems for different applications. The key application areas of PCFs vary from telecommunications and high-power energy transmission to quantum optics and sensing. The stack-and-draw method is a standard manufacturing technique for MOFs, where a preform is first manually created and then drawn in a high-tech furnace into a fibre with the required final dimensions and position of the air holes. Since in the manufacturing process experimenters can control only a few parameters, mathematical models and numerical simulations of the drawing process are highly requested. They not only allow to deepen the understanding of physical phenomena occurring during the drawing process, but they also accurately predict the final cross-section shape and size of the fibre. In this manuscript, we assume thermal equilibrium between the furnace and the fibre and propose a functional form of the fibre temperature distribution. We utilise it with asymptotic mass, momentum, and evolution equations for free surfaces already available in the literature to describe the process of fibre drawing. By doing so, the complex heat exchange problem between the fibre and the furnace need not be solved. The numerical results of the whole asymptotic model overall agree well with experimental data available in the literature, both for the case of annular capillaries and for the case of holey fibres.

A signed graph is an undirected graph such that all of its edges are labeled positive or negative. Let D be an embedding of a signed graph G in the Euclidean line. If in D for all of the vertices their positive neighbors are closer than the negative neighbors, then D is called a valid drawing of G. In this paper we show that signed trees, unicyclic graphs, and ladder graphs have a valid drawing in the Euclidean line.

In this paper, a new method by combining cold drawing and martensitic transformation was proposed to produce ultrahigh-strength steel wire, and the effect of austenitizing heating rate on microstructure and mechanical properties was studied. Compared with Muffle furnace heating, salt bath heating has a much higher austenitizing heating rate, which is beneficial to obtain ultrafine-grained martensite for steel wire with a larger section. By salt bath hardening and low-temperature tempering, an ultrahigh strong (strength of 2.48 GPa) and tough (elongation of 6.0%) steel wire was produced. Moreover, to explore whether is it possible to replace long-time low-temperature tempering with short-time tempering at elevated temperatures to improve the tempering efficiency, the effect of tempering time on the evolution of microstructure and mechanical properties of the steel wires tempered at 350 °C was systematically studied. The results demonstrate that tempering at 350 °C for 30 s can endow the steel wire with comparable mechanical properties to that of the one tempered at 250 °C for 2 h. With tempering time prolonging, the strength decreases gradually with the precipitated phase transition from χ-Fe5C2 carbide into θ-Fe3C carbide and coarsening, which plays a major role in the strength decrease.

The coordination polymer [Fe(NH₂trz)₃](2ns)₂ exhibits the rare phenomenon of spin crossover in an attractive temperature range, i.e., somewhat above room temperature. Spin crossover in [Fe(NH₂trz)₃](2ns)₂ is manifest by thermochromism, which is accompanied by a magnetic transition from diamagnetism to paramagnetism. However, [Fe(NH₂trz)₃](2ns)₂ is brittle and difficult to process, which limits its use. In this study, we show that [Fe(NH₂trz)₃](2ns)₂ can be co-processed with ultrahigh molecular weight polyethylene (UHMWPE), which possesses outstanding mechanical properties, particularly when tensile drawn. Therefore, [Fe(NH₂trz)₃](2ns)₂–UHMWPE blends were gel-processed by extrusion, employing a relatively poor solvent, which has recently been shown to offer advantages compared to good solvents. Uniform and flexible films, ribbons and fibers with [Fe(NH₂trz)₃](2ns)₂ fractions as high as 33.3% m/m were obtained that could be readily drawn. Spin crossover in the coordination polymer is retained in these materials, as evident from their thermochromism. The tensile strength and Young’s modulus of the blends exceed those of typical commodity polymers. Thus, the films, ribbons and fibers constitute a special class of multifunctional materials that combine the flexibility and excellent mechanical properties of drawn UHMWPE with the spin crossover behavior of [Fe(NH₂trz)₃](2ns)₂.

Owing to the reduction of rupture instability and the avoidance of wrinkle defect, hydrodynamic deep drawing (HDD) process is gradually becoming attractive for fabricating lightweight and complicated products. Meanwhile, since metallic material presents anisotropic deformation behavior, it is necessary to select an appropriate constitutive model for the prediction of plastic deformation behavior of applied material with high precision. In the present research, several anisotropic yield criteria namely, Hill’48, Yld2000-2d and BBC2005 are implemented to investigate the effect of yield functions on the prediction accuracy of the critical process window and deformation behavior for HDD process of 2024 and 5754 aluminum alloys. Material constants in the yield criteria are determined by applying uniaxial and equi-biaxial tension tests and optimizing an error-function by using the Levenberg-Marquardt algorithm. Furthermore, the process window diagram is computed utilizing the stress analytical model combined material properties with workpiece geometrical features. Numerical simulation results of predicted material anisotropic parameters, process window and HDD deformation for aluminum alloys are compared with the experimental data. Through the comparison of diverse yield criteria based on materials anisotropic coefficients, critical process window prediction, earing profile, and thickness distribution, it is revealed that the Yld2000-2d and the BBC2005 yield criteria can offer more precise models of material behavior in planar anisotropy properties for HDD process of 2024 and 5754 aluminum alloys.

The paper deals with the reverse engineering, namely the as built documentation of the actual construction. The input is data measured in field using geodetic methods. In addition to modern methods of surveying 3D objects, such as laser scanning, it is still necessary to use classic surveying using a total station. The bottle neck of the process is the creation of documentation of the construction, which is still created manually in the appropriate CAD/BIM software. The goal of the research was to find a method that would reduce the amount of manual work when drawing documentation in CAD/BIM to a minimum. The core of the solution is the use of a topology that interconnects the points measured in field. The entire procedure has 2 parts: 1. Creating a topo-logical drawing template in a suitable CAD/GIS software (digital sketch), 2. Adding geometry to this sketch and creating a drawing using topological codes. The method was verified in practice by applying it to several specific buildings in the Czech Republic. The practical application of the method demonstrated a 30% time saving, a reduction in work and error rate in the entire process.

Among the leading immersive technologies, Augmented Reality is one of the most promising and empowering to support designers in production environments. This research investigates the application of mobile augmented reality, based on the Web, as a mediation tool focused on cognitive activities of reading and understanding of Technical Drawings in the production and assembly for Tailor Made projects of the scenographic industry. In this context, the research presents a method to use the WebAR to improve the reading of technical drawings, seeking efficiency on the visualization of models and the exchange of information between professionals, involved in the processes of design, production and assembly of products, in the scope of scenography. This mediation tool was developed using Web AR platforms, compatible with native libraries (ARCore and ARKit) to ensure, first, compatibility with commonly used devices that workers or businesses can access, and secondly, to leverage hybrid tracking techniques that combine vision and sensors to improve the reliability of augmented reality viewing. The proposed solution adopts multiple tracking and navigation techniques in order to expand Space Skills components to provide greater exploratory freedom to users. The research process took place in the light of the Design Science Research Methodology and the DSR-Model, since it aimed to develop a solution to a practical problem, as well as to produce knowledge from this process. Field experiments were conducted in two real companies, with end users on their respective mobile devices, in order to evaluate usability and behavioral intent, through the Acceptance, Intent and Use of Technology questionnaires; and perceived mental workload, NASA-TLX. The experimental results show that the adoption of this tool reduces the cognitive load in the process of reading technical drawings and project´s understanding. In general, it´s usability and intent to use provide significant levels of satisfaction, being positively accepted by all participants involved in the study.