Digital-based differential amplifiers (DDA) are particularly suitable to low voltage digital integrated circuit technologies. This paper presents an exhaustive analysis of the digital-based analog amplifiers to take advantage of today's high-performance digital technologies and of computer-aided design (CAD) commonly employed to design integrated circuits. The operating principle and the main mathematical relations of the digital-based differential amplifiers are discussed along with an exhaustive explanation of its operating regions and of the corresponding power consumption. Finally, a detailed description of the design procedure of in UMC 180nm standard CMOS technology is shown.

Characteristics of artificial waveguide lines composed of finite size artificial cells are analyzed and discussed with relation to designing the travelling wave parametric amplifiers. From this point of view, flux driven amplifier suggested recently can be considered as the most successful amplifier design. To increase dynamic range of the amplifier, dc SQUID cells of the artificial line in use can be substituted for bi-SQUID cells. The 1-dB compression points of the amplifier gain are calculated and compared for both types of the cells.

The authors of the article performed computer simulation of buffer amplifiers (BA), which have medium and extremely small values of the offset voltage's systematic component (V_off), for different technological processes (Si, GaAs and GaN). The proposed control units are distinguished by a small number of elements and allow operation in the range of low and high temperatures. The variants of circuitry implementation of control units based on GaAs, GaN depletion-mode CMOS and JFET technological processes are considered. The results of the comparative modeling showed that the basic circuit of the BA on two field-effect transistors, when implemented on various modifications of GaN MOS and depletion-mode MOS transistors, provides sufficiently low values of the offset voltage's systematic component (less than 2 μV). The proposed BAs are designed for use in the structure of the Sallen-Key low-pass filter (LPF) when they are implemented both on mid-frequency Si CJFET and on GaAs microwave transistors. Low values of the LPF V_off have a positive effect on the effective capacity of the ADC. An example of switching on a BA in the JFET OpAmp structure based on the depletion-mode MOS input stage and a “folded” cascode, which, with 100% negative feedback, can be used in the Sallen-Key LPF, is considered. Computer simulation of the JFET/MOS OpAmp showed that the OpAmp has an open-loop voltage gain of 76-85dB, and its V_off is within 7µV in the temperature range from -60°C to +120°C. The presented circuitry of buffer amplifiers is intended, first of all, for the tasks of designing precision Sallen-Key low-pass filter (low-pass filter, high-pass filter, PF, RF).

Micro plasma devices (MPD) with power gains are of interest in applications involving operations in the presence of ionizing radiations, in propulsion, in control, amplification of high power electromagnetic waves, and in metamaterials for energy management. Here we review and discuss MPDs with an emphasis on new architectures that have evolved during the past 7 years. Devices with programmable impact ionization rates and programmable boundaries are developed to control the plasma ignition voltage and current to achieve power gain. Plasma devices with 1-10 μm gaps are shown to operate in the sub-Paschen regime in atmospheric pressures where ion-assisted field emission results in a breakdown voltage that linearly depends on the gap distance in contrast to the exponential dependence dictated by the Paschen curve. Small gap devices offer higher operation frequencies at low operation voltages with applications in metamaterial skins for energy management and in harsh environment inside nuclear reactors and in space. In addition to analog plasma devices, logic gates, digital circuits, and distributed amplifiers are also discussed.

Fiber laser technology has been demonstrated as a versatile and reliable approach for laser source manufacturing with a wide range of applicability in various fields ranging from science to industry. The power/energy scaling of single fiber laser systems has faced several fundamental limitations. To overcome them and to boost the power/energy level even further, combining the output powers of multiple lasers has become the primary approach. Among various combining techniques, the coherent beam combining of fiber amplification channels is the most promising approach, instrumenting ultra-high power/energy lasers with near-diffraction-limited beam quality. This paper provides a comprehensive review of the progress of coherent beam combining for both continuous-wave and ultrafast fiber lasers. The concept of coherent beam combining from basic notions to specific details of methods, requirements, and challenges are discussed, along with reporting some practical architectures for both continuous and ultrafast fiber lasers.

Optical parametric amplification (OPA) represents a powerful solution to achieve broadband amplification in wavelength ranges beyond the scope of conventional gain media, for generating high-power optical pulses, optical microcombs, entangled photon pairs and a wide range of other applications. Here, we demonstrate optical parametric amplifiers based on silicon nitride (Si₃N₄) waveguides integrated with two-dimensional (2D) layered graphene oxide (GO) films. We achieve precise control over the thickness, length, and position of the GO films using a transfer-free, layer-by-layer coating method combined with accurate window opening in the chip cladding using photolithography. Detailed OPA measurements with a pulsed pump for the fabricated devices with different GO film thicknesses and lengths show a maximum parametric gain of ~24.0 dB, representing a ~12.2 dB improvement relative to the device without GO. We perform a theoretical analysis of the device performance, achieving good agreement with experiment and showing that there is substantial room for further improvement. This work demonstrates a new way of achieving high photonic integrated OPA performance by incorporating 2D materials.

Symbolic pole/zero analysis is an important step when designing an analog operational amplifier. Generally, a simplified symbolic analysis of analog circuits suffers from NP-hardness, i.e., an exponential growth of the number of symbolic terms of the transfer function with the circuit size. In this study, we present a mathematical model combined with a heuristic-metaheuristic solution method for the symbolic pole/zero simplification in operational transconductance amplifiers (OTA). At first, the circuit is symbolically solved and an improved root splitting method is applied to extract symbolic poles/zeroes from the exact expanded transfer function. Then, a hybrid algorithm based on heuristic information and a metaheuristic technique using simulated annealing is performed for the simplification of the derived symbolic pole/zero expressions. The developed method has been tested on three analog OTAs. The obtained results show the effectiveness of the proposed method to achieve accurate simplified symbolic pole/zero expressions with the least complexity.

In this paper consider the circuitry of voltage followers (VF) with unity-gain, intended for practical use in active Sallen-Key RC-filters (LPF, HPF, BPF, RF). The results of research and computer modeling of radiation-resistant and low-temperature VF in the LTSpice environment on models of CJFET transistors operating under the influence of neutron flux up to 10e14 n/cm2 and cryogenic temperatures up to -197°C are presented.

Non-Linear Simulation by Harmonic Balance Techniques of Load Modulated Power Amplifier Driven by Random Modulated Signals. Comparison with measured results.

The human ankle is a complex joint, most commonly represented as talocrural and subtalar axes. It is difficult to locate and take in vivo measurements of the ankle joint. There are no instruments for patients lying on a bed or the floor; that can be used in outdoor or remote sites. We have developed a "Turmell-meter" to address these issues. We started with the study of ankle anatomy and anthropometry, then we used the product of exponentials’ formula to visualize the movements. Furthermore, we built a prototype using human proportions and statistics. For pose estimation, we used a trilateration method by applying tetrahedral geometry. Additionally, we computed the axis direction by fitting 3D circles, plotting the manifold and chart as an ankle joint model. We presented the results of simulations, a prototype comprising 45 parts, specifically designed draw-wire sensors, and electronics. Finally, we tested the device by capturing positions and fitting them into the bi-axial ankle model as a Riemannian manifold. The Turmell-meter is intended to be a hardware platform for human ankle joint axis estimation, it is adjustable and has an easy setup. The proposed model has the properties of a chart in a geometric manifold, we provided the details