We propose a deep learning algorithm that directly compensates for luminance degradation owing to the deterioration of organic light emitting diode (OLED) devices to address the burn-in phenomenon of OLED displays. Conventional compensation circuits are encumbered by a high cost of development and manufacturing processes owing to their complexity. However, given that deep learning algorithms are typically mounted on a system on chip (SoC), the complexity of the circuit design is reduced, and the circuit can be reused by re-learning only the changed characteristics of the new pixel device. The proposed approach comprises deep feature generation and multi-stream self-attention, which decipher the importance of the variables, and the correlation between burn-in-related variables. It also utilizes a deep neural network that identifies the nonlinear relationship between the extracted features and luminance degradation. Thereafter, the luminance degradation is estimated from the burn-in-related variables, and the burn-in phenomenon can be addressed by compensating for the luminance degradation. The experimental results revealed that compensation was successfully achieved within an error range of 4.56%, and demonstrate the potential of a new approach that can mitigate the burn-in phenomenon by directly compensating for pixel-level luminance deviation.

Ultrasonic sensors are inexpensive and can take measurements with high accuracy, even with simple hardware configurations, so they are used in various fields. When multiple ultrasonic sensors exist in the measurement space, crosstalk occurs due to other nodes, which causes measurement errors. Crosstalk includes not only receiving homogeneous signals from other nodes, but also overlap by other signals, and interference by heterogeneous signals. This paper proposes a method that uses frequency sweep keying modulation to be robust against overlap and a faster region-based convolutional neural networks (R-CNN)-based demodulator to reduce the interference caused by heterogeneous signals. The demodulator works by training faster R-CNN with the spectrograms of various received signals and classifying the received signals using a faster R-CNN. Experiments implementing an ultrasonic crosstalk environment showed that compared to on-off keying (OOK), phase-shift keying (PSK), and frequency-shift keying (FSK), the proposed method can implement CDMA even with shorter codes, and is robust against overlap. Compared to correlation-based frequency sweep keying, the time-of-flight error was reduced by approximately 75%. While existing demodulators did not consider heterogeneous signals, the proposed method ignored approximately 99% of the OOK and PSK signals, and approximately 79% of the FSK signals. The proposed method performs better than the existing methods and is expected to be used in various applications.

Although commercially-available low-cost air quality sensors have low accuracy, the sensor system are being used to collect the data for the regulation of PM2.5 emission caused by industrial activities or to estimate the personal exposure for PM2.5. In this work, to solve the accuracy problem of low-cost PM sensor, we developed a new PM2.5 calibration model by combining the deep neural network (DNN) optimized in calibration problem and a LSTM optimized in time-dependent characteristics. First, two datasets were generated to test the accuracy performance and generalization performance of the PM2.5 calibration machine learning (ML) model. The PM2.5 concentrations, temperature and humidity by low-cost sensor and gravimetric-based PM2.5 measuring instrument were sampled for a sufficiently long time. The proposed model was compared with benchmark (multiple linear regression model) and low-cost sensor results. For root mean square error (RMSE) for PM2.5 concentrations, the proposed model reduced 41-60% of error compared to the raw data of low-cost sensor, and reduced 30-51% of error compared to the benchmark model. R2 of ML model, MLR and raw data were 93, 80 and 59 %. Also, the developed model still showed consistent calibration performance when calibrated with new sensors in different locations. Low-cost sensors combined with ML model not only can improve the calibration performance of benchmark, but also can be applied to the sensor monitoring systems for various epidemiologic investigations and regulatory decisions.

The composition of fine-ground lead zirconate-titanate powder Pb(Zr_0.52Ti_0.48)O₃, suspended in PZT and bismuth titanate (BiT) solutions, is deposited on the curved surface of IN718 and IN738 nickel-based supper alloy substrates up to 100 µm thickness. Photochemical metal organic and infiltration techniques are implemented to produce smooth, semi-dense, and crack-free random orientated thick piezoelectric films as piezo-sensors, free of any dopants or thickening polymers. Every single layer of the deposited films is heated at 200 °C with 10 wt.% excess PbO, irradiated by UV lamp (365 nm, 6 watt) for 10 minutes, pyrolyzed at 400 °C, and subsequently annealed at 700 °C for one hour. This process is repeated successively until reaching the desired thickness. Au and Pt thin films are deposited as the bottom and top electrodes using evaporation and sputtering methods, respectively. PZT/PZT and PZT/BiT composite films are then characterized and compared to similar PZT and BiT thick films deposited on the similar substrates. The effect of composition and deposition process is also investigated on the crystalline phase development and microstructure morphology as well as dielectric, ferroelectric and piezoelectric properties of piezo-films. The maximum remnant polarization of P_r = 22.37 ± 0.01, 30.01 ± 0.01 µC/cm², the permittivity of ε_r = 298 ± 3, 566 ± 5 and piezoelectric charge coefficient of d₃₃ = 126, 148 m/V were measured versus the minimum coercive field of E_c = 50, 20 kV/cm for the PZT/PZT and PZT/Bit thick films, respectively. The thick film piezo-sensors are developed to be potentially used at frequency bandwidth of 1–5 MHz for rotary structural health monitoring and also in other industrial or medical applications as a transceiver.

We report a self-assembly synthesis of silicon nanoparticles/nitrogen-doped reduced graphene oxide/ carbon nanofiber (Si@N-doped rGO/CNF) composites as potential high-performance anodes for rechargeable lithium-ion batteries (LIB) through the electrostatic attraction between amino and carboxyl groups. Nitrogen atoms generate a large number of vacancies or defects on the graphite plane, providing additional transmission channels for the diffusion of lithium ions, and improving the conductivity of the electrode. Carbon nanofiber (CNF) can help maintain the stability of the electrode structure and prevent silicon nanoparticles from falling off the electrode, prevent silicon nanoparticles from being directly exposed to the electrolyte, and can form a stable solid electrolyte interface (SEI) film. The three-dimensional conductive structure composed of Si, nitrogen atom-doped reduced graphene oxide (N-doped rGO), and CNF can effectively buffer the volume changes of silicon nanoparticles, shorten the transmission distance of lithium ions (Li+) and electrons, and make the electrode have good conductivity and stability in mechanical properties. In addition, compared with the Si@N-doped rGO and Si/rGO/CNF composite electrode, the Si@N-doped rGO/CNF composite electrode shows good cycle performance and rate capability, and its reversible specific capacity can reach 1418.8 mAh/g. The capacity retention rate is 64.7%, and the coulomb efficiency is 95%.

The severe volumetric expansion of silicon nanoparticles (~400 %) limits their practical application as an anode material for next-generation lithium–ion battery (LIB). Here, we describe the fabrication and characterization of conformal polydopamine carbon shell encapsulating rattle-type silica@silicon nanoparticles (PDA−PEI@PVP−SiO2@Si) with tunable void structure prepared following a dual SiO2 template using (3–aminopropyl)triethoxysilane (APTES) as a self-catalytic, structure-directing agent to tetraethyl orthosilicate (TEOS) pretreated with polyvinylpyrrolidone (PVP K30) via modified Stöber process. Polyethylene imine (PEI) crosslinking facilitated the construction of interconnected three-dimensional bubble wrap-like carbon matrix structure through hydrothermal treatment, pyrolysis, and subsequent surface-protected etching. The composite anode material delivered 539 mAh·g−1 capacity after 100 cycles at 0.1 A·g−1, and 453 mAh·g−1 rate performance at 5 A·g−1. The satisfactory electrochemical performance of the PDA−PEI@PVP−SiO2@Si was attributed to the following: the rattle-type structure providing void space for Si volume expansion, PVP K30-pretreated APTES/TEOS SiO2 seeds via catalyst-free, hydrothermal-assisted Stöber protecting Si/C spheres upon etching, carbon coating strategy increasing Si conductivity while stabilizing the solid electrolyte interface (SEI), and PEI carbon crosslinks providing continuous conductive pathways across the electrode structure. The present work realizes a promising strategy to synthesize the tunable yolk–shell C@void@Si composite anode materials for high power/energy-density LIB applications.

Background and objectives: TSC1 is a crucial component of the mTOR pathway, impacting cell growth, proliferation, and autophagy, while TSC2 is a tumor suppressor gene that regulates cell growth and is associated with the mTOR signaling pathway. In the present study, we analyzed TSC1 and TSC2 mRNA expression levels in rectal cancer, and evaluated the clinicopathological and prognostic characteristics of TSC1 and TSC2. Materials and Methods: TSC1 and TSC2 mRNA expression was examined in various cancer types. We further evaluated survival to determine the prognostic significance of TSC1 and TSC2 mRNA in CRC using The Cancer Genome Atlas (TCGA) data. Results: The study focused on rectal cancer, as it exhibited the most promising results. The patients were split into two subgroups, each comprising 50% of the total, based on the TSC gene expression levels. This division was made to assess the clinical characteristics associated with the expression of TSC1 and TSC2 genes. In the study, lower TSC1 expression was linked to venous invasion in rectal cancer patients, and there was also a related trend with lymphatic invasion, although it didn't reach statistical significance. Lower TSC2 expression was observed in younger patients and had some associations with sex and M stage, but these correlations were not statistically significant. When it came to survival analysis, TSC1 expression did not significantly impact overall survival, while higher TSC2 expression was associated with a poorer prognosis in rectal cancer. To enhance our comprehension, additional research, especially in larger case studies, is needed to explore the molecular mechanisms and clinical characteristics of TSC genes in colorectal cancer.

Multidrug resistant (MDR) bacteria have become a severe problem for public health. Developing new antibiotics for MDR bacteria is difficult, from inception to the clinically approved stage. Here, we have used a new approach; we have modified the antibiotic, ciprofloxacin (CFX), with triphenylphosphonium (TPP, PPh3) moiety via ester- (CFX-ester-PPh3) and amide-coupling (CFX-ester-PPh3), to target bacterial membranes. In this study, we have evaluated the antibacterial activities of CFX and its derivatives against 16 species of bacteria, including MDR bacteria, using minimum inhibitory concentration (MIC) assay, morphological monitoring, and expression of resistance-related genes. TPP-conjugated CFX, CFX-ester-PPh3 and CFX-amide-PPh3 showed significantly improved antibacterial activity against Gram-positive bacteria, Staphylococcus aureus, including MDR S. aureus (MRSA) strains. The MRSA ST5 5016 strain showed high antibacterial activity, with an MIC values of 11.12 µg/mL for CFX-ester-PPh3 and 2.78 µg/mL for CFX-amide-PPh3. The CFX derivatives inhibited biofilm formation in MRSA by more than 74.9% of CFX-amide-PPh3. In the sub-MIC, CFX derivates induced significant morphological changes in MRSA, including irregular deformation and membrane disruption, accompanied by a decrease in the level of resistance-related gene expression. With these promising results, this method is very likely to combat MDR bacteria, through a simple TPP moiety modification of known antibiotics, which can be readily prepared at clinical sites.

Anesthetics reduce cardiac functions and lower blood pressure (BP), potentially causing excessive BP reduction in dehydrated patients or those with heart conditions, such as coronary artery disease (CAD). Considering the increased prevalence of cardiovascular disease with age, anesthesiologists must be cautious about BP reduction during general anesthesia in older adults. In the present case, an undiagnosed CAD patient in a hypovolemic state experienced a significant systolic blood pressure drop to the 50s during propofol and sevoflurane anesthesia. Despite the use of vasopressors, excessive hypotension persisted, leading to anesthesia suspension. Subsequent cardiac examinations, including computed tomography heart angio and calcium score, and coronary angiogram, revealed a near total occlusion of the left main coronary artery and the formation of collateral circulation. After 5 days of hydration and anticoagulation medications and confirmation of normovolemic state, general anesthesia was attempted again and successfully induced; a normal BP was maintained throughout the surgery. Thus, it is important to conduct a thorough cardiac evaluation and maintain normovolemia for general anesthesia in older adults.

Silica aerogels and their derivatives have outstanding thermal properties with exceptional values in the thermal insulation industry. However, the brittle nature restricts its large-scale commercialization. Thus, enhancing their mechanical strength without affecting their thermal insulating properties is essential. Therefore, for the first time, highly thermally stable Poly(acrylamide-Co-acrylic acid) partial sodium salt is used as a reinforcing polymer to synthesize hybrid P(AAm-CO-AAc)-silica aerogels via epoxy ring-opening polymerization in the present study. Functional groups in P(AAm-CO-AAc) partial sodium salts, such as CONH2 and COOH, acted as nucleophiles for the epoxy ring-opening reaction with (3-glycidyloxypropyl)trimethoxysilane, which resulted in a seven-fold enhancement in mechanical strength compared to that of a pristine silica aerogel while maintaining the thermal conductivity at less than 30.6 mW/mK and porosity of more than 93.68%. Moreover, the hybrid P(AAm-CO-AAc)-silica aerogel demonstrated improved thermal stability up to 343 ⁰C owing to the synergetic effect between P(AAm-CO-AAc) and the silica aerogel, corresponding to thermal stability and strong covalent bonding among them. These excellent results illustrate that this new synthetic approach for producing hybrid P(AAm-CO-AAc)-silica aerogels is useful for enhancing the mechanical strength of a pristine silica aerogel without impairing its thermal insulating property and shows potential as an industrial heat insulation material.

This retrospective study aimed to evaluate the impact of radiation dose on the outcomes of stereotactic radiosurgery (SRS) for benign meningiomas and determine an optimal dosing strategy for balancing tumor control and treatment-related toxicity. Clinical data of 147 patients with 164 lesions treated between 2014 and 2022 were reviewed. Primary outcomes included progression-free survival (PFS), local control rate (LCR), and radiation-induced toxicity, with secondary outcomes focusing on LCR and radiation-induced peritumoral edema (PTE) in two dose groups (≥14 Gy and <14 Gy). Results revealed a median follow-up duration of 47 months, with 1-year, 2-year, and 5-year PFS rates of 99.3%, 96.7%, and 93.8% respectively, and an overall LCR of 95.1%. Radiation-induced toxicity was observed in 24.5% of patients, primarily presenting mild symptoms. Notably, no significant difference in LCR was found between the two dose groups (P = 0.628), while Group 2 (<14 Gy) exhibited significantly lower PTE (P = 0.039). The study concludes that SRS with a radiation dose <14 Gy demonstrates comparable tumor control with reduced toxicity, advocating for consideration of such dosing to achieve a balance between therapeutic efficacy and safety.

Australia’s mental health system is failing young people. Calls for accountability, strategic long-term policy planning, and regional leadership have been identified as solutions to guide mental health reform. Developing system dynamics models using a participatory approach (participatory systems modelling, PSM) is recognised as a useful method that can support decision-making for strategic reform. This paper reports evaluation findings of a youth mental health PSM process conducted in the Australian Capital Territory (ACT). Baseline and follow-up mixed-methods evaluation data were collected in 2022 across diverse stakeholder groups to investigate the feasibility, value, impact, and sustainability of PSM. Though youth mental health system reform was viewed as desirable and a necessity across all stakeholder groups, shared perceptions of disabling powerless was observed regarding their ability to influence current decision-making processes to improve the youth mental health system. This suggests greater accountability is required to support systemic reform in youth mental health. PSM offers promise in improving transparency and accountability of decision-making for youth mental health as exemplified in the ACT. However, more support and time are required to facilitate transformational change. Future research should investigate empowerment strategies to complement the implementation of findings from dynamic models developed through PSM, as well as the effectiveness of regional youth mental health policy decision-making supported by systems modelling.

Wafer-scale blue micro-light-emitting diode (micro-LED) arrays are fabricated with a pixel size of 12 μm, a pixel pitch of 15 μm, and a pixel density of 1692 pixels per inch, achieved by optimizing the properties of e-beam-deposited and sputter-deposited indium tin oxide (ITO). Although the sputter-deposited ITO (S-ITO) films exhibit a densely packed morphology and lower resistivity compared to those of the e-beam-deposited ITO (E-ITO) films, the forward voltage (VF) values of a micro-LED with the S-ITO films are higher than those with the E-ITO films. The VF values for a single pixel and for four pixels with E-ITO films are 2.82 V and 2.83 V, respectively, while the corresponding values for S-ITO films are 3.50 V and 3.52 V. This was attributed to ion bombardment damage and nitrogen vacancies in the p-GaN layer. Surprisingly, the VF variations of a single pixel and of four pixels with the optimized E-ITO spreading layer from five different regions are only 0.09 V and 0.10 V, respectively. This extremely uniform VF variation is suitable for realizing micro-LED displays to be used in AR and VR applications, circumventing the bottleneck in the development of long-lifespan and high-brightness organic LED devices for industrial mass production.