This paper discusses domestic problem of waiting hot water for the shower use till it reaches satisfactory temperature, which result a lot of wastage in fresh water. The outcome from research survey shows that there is no satisfactory solution till now as all solutions were either expensive or with no effective results. Local small inline electric heater equipped with fuzzy logic controller is proposed in this paper to be installed just before the showerhead to measure the water temperature and flow before the showerhead, as control input-variables, and decide the operating voltage of the heater, as control output-variable (MISO). MATLAB Simulink is used to model the proposed system. Different test cases are simulated to prove the performance and the safe operation of the system. Techno-economic study is carried out to determine the “Direct Benefits” and “Indirect Benefits” that can be achieved if such system is implemented in wide range. Azerbaijan data is taken as an example to calculate the economic benefits. The results show important benefits not only for economy but also for climate and the reduction of CO₂ gas emission. Different economic indices are provided to be an easy reference for decision makers and project managers.

Environmental pollution is becoming ubiquitous; it has a negative impact on the ecosystem diversity and worsens the quality of human life. This review discusses the possibility of applying the Plant Microbial Fuel Cells (PMFC) technology for concurrent processes of electricity generation, purification of water and soil ecosystems from organic pollutants, in particular, from synthetic surfactants and heavy metals. The review describes the PMFC functioning mechanisms and highlights the issues of the PMFC environmental application. Generally, this work summarizes different approaches to the PMFC development and to the potential usage of such hybrid bioelectrochemical systems for the environmental protection.

(1) Background: Human-generated greenhouse gas (GHG) emissions are the largest contributor to climate change worldwide. Climate change negatively impacts human and planetary health threatening the existence of life on earth. The healthcare industry is responsible for approximately 8.5% of carbon emissions in the United States. Measuring baseline GHG emissions is the first step in emissions reduction. However, very few models of measurement exist for health care organizations. This project aimed to develop and implement a program to measure and track GHG emissions at a Midwestern Academic Medical Center (MAMC) and to educate staff to manage the process. (2) Methods: A Plan, Do, Study, Act (PDSA) cycle and Quality Improvement methodology was used to develop, implement, and assess a standardized GHG emission inventory process to measure Scope 1 and Scope 2 baseline emissions, and provide virtual training and education to the accountable staff. A pre- and post-survey design was used to measure the knowledge and readiness of the staff after the implementation of the GHG inventory training. (3) Results: The GHG inventory process was validated through an external verification process and the measurement of Scope 1 and Scope 2 baseline GHG emissions was completed and verified for accuracy through a data comparison review. The pre-post-training survey showed an increase in the knowledge and readiness of staff in maintaining a GHG inventory. (4) Conclusions: This work shows the feasibility of obtaining baseline GHG emissions data at large medical centers. It represents the initial phase of the overarching goal to develop site-wide and system-wide carbon reduction strategies and a climate action plan within this health system.

High efficacy LED lamps combined with adaptive lighting control and greenhouse integrated photovoltaics (PV) could enable the concept of year-round cultivation and become a feasible option even in the harsh climate of the Nordic countries. Meteorological satellite data of this region was analyzed in a parametric study to evaluate the potential of these technologies. The generated maps showed monthly average temperatures fluctuating from -20°C to 20°C throughout the year. The natural photoperiod and light intensity also changed drastically, resulting in monthly average daily light integral (DLI) levels ranging from 45-50 mol·m-2·d-1 in summer and contrasting with 0-5 mol·m-2·d-1 during winter. To compensate, growth room cultivation independent from outdoor conditions could be used in winter. Depending on the efficacy of the lamps, the electricity required for sole-source lighting at 300 µmol·m-2·s-1 for 16 hours would be between 1.4 and 2.4 kWh·m-2·d-1. Greenhouses with supplementary lighting could help start the cultivation earlier in spring and extend it further into autumn. The energy required for lighting highly depends on several factors such as the natural light transmittance, the light threshold settings and the lighting control protocol, resulting in electric demands between 0.6 and 2.4 kWh·m-2·d-1. Integrating PV on the roof or wall structures of the greenhouse could offset some of this electricity, with specific energy yields ranging from 400 to 1120 kWh·kWp-2·yr-1 depending on the region and system design.

Fertility management techniques being promoted in sub-Saharan Africa (SSA) seek to grow indigenous vegetables economically and sustainably. This study was conducted in a phytotron chamber and compared yield, soil carbon (C) speciation and greenhouse gas (nitrous oxide (N₂O) and carbon dioxide (CO₂)) emissions from SSA soils of two ecoregions; the dry savanna (lna, Republic of Benin) and rainforest (Ife, Nigeria) cultivated with local amaranth (Amaranthus cruentus) under manure (5 t/ha) and/or urea (80 kg N/ha) fertilization. Vegetable yield ranged from 1753 kg/ac to 3198kg/ac in the rainforest, RF, soils and 1281 kg/ac to 1951 kg/ac in the dry savanna, DS, soils. Yield in the urea treatment was slightly higher compared to the manure+urea treatment, but the difference was not statistically significant. Cumulative CO₂ emissions over 21 days ranged from 497.06 to 579.47 g CO₂ in the RF, and 322.96 to 624.97 g CO₂ in the DS, while cumulative N₂O emissions ranged from 60.53 to 220.86 mg N₂O in the RF, and 24.78 to 99.08 mg N₂O in the DS. In the RF samples, the combined use of manure and urea reduced CO₂ and N₂O emissions but led to an increase in the DS samples. ATR-FTIR analysis showed that the combined use of manure and urea increased the rate of microbial degradation in the soils of the DS, but no such effect was observed in soils of the RF. We conclude that combining manure and urea fertilization has different effects on soils of the two ecoregions, and that RF farmers can reduce agricultural emissions without compromising soil productivity and yield potential.

Rice provides ~20% of human dietary energy and, for many people, a similar share of their protein. Rice cultivation, however, produces significant greenhouse gas (GHG) emissions, comparable to those from the aviation sector. The main GHG from rice production is methane, mostly a result of conventional rice cultivation (CRC) keeping rice fields continuously flooded during the crop cycle. There is extensive evidence that alternate wetting and drying (AWD) of rice fields substantially reduces methane emissions. AWD is one component of the System of Rice Intensification (SRI), an agroecological approach to the management of plants, water, soil and nutrients practiced by millions of farmers in both lowland irrigated rice and upland rainfed cultivation. Thirteen countries have included SRI in their Nationally Determined Contributions to GHG reduction or climate change mitigation. This article reviews 16 field studies of the net reduction in GHG emissions from the adoption of AWD, eight from the adoption of SRI, and two that compared SRI and AWD. Where available, the review includes data on yield and therefore on carbon dioxide-equivalent GHG emissions per kilogram of rice produced. The evidence indicates that AWD and SRI offer a similar and substantial reduction (~35–41%) in GHG emissions per hectare compared with conventional rice cultivation. However, SRI offers ~66% greater yield than CRC, and therefore greater reduction in emissions per kilogram of rice, ~54% more than AWD. The limited data directly comparing SRI and AWD support this finding. SRI also appears to have greater potential to sequester carbon in the soil. SRI lowers rice farmers’ costs of production, adds to their income and can make climate-friendly methods more attractive. Both AWD and SRI are greatly preferable to current conventional practices, but SRI offers opportunities to contribute to food security while directly addressing the drivers of climate change.

Initial evaluations of the System of Rice Intensification in India and elsewhere have mainly fo-cused on its impact on yield and income and have usually covered just one or two seasons. Re-searchers at the ICAR-Indian Institute of Rice Research conducted a more comprehensive evalua-tion of SRI methods over six years (six wet and six dry seasons), comparing these methods with three other rice crop management systems: modified, partially mechanized SRI (MSRI); direct-seeded rice (DSR); and normal transplanting with inundated fields (NTP). SRI grain yield was found to be about 50% higher than with NTP (6.35 t ha-1 vs 4.27 t ha-1), while the MSRI yield was essentially the same (6.34 t ha-1) and 16% higher than with DSR (5.45 t ha-1). Compared to NTP, SRI methods significantly enhanced soil microbial populations over time, bacteria by 12%, fungi by 8%, and actinomycetes by 20%. Indicators of biological activity in the rhizosphere were also higher, dehydrogenase by 8.5% and FDA enzymes by 16%. Glucosidase activity, an indicator of soil organic matter, was 78% higher. Relative to normal transplanting methods, SRI reduced GHG emissions by 21%, while DSR reduced them by 23% and MSRI by 13%, which indicated pos-itive effects of the alternate and improved methods over normal transplanting. Economic analy-sis showed that both gross and net economic returns to be higher with SRI than with MSRI and the other management systems evaluated. While the six-year study documented many ad-vantages of SRI crop management, the MSRI version evaluated is a promising adaptation that provide similar benefits but with lower labor requirements.

Cement manufacturing is one of the most energy-intensive industries in the world. Most of the cost of producing cement is accounted by fuel consumption and power expenditures. Thermal power plants are the major source of electricity in Pakistan. But they are not efficient and environmentally friendly. This study simulates four different models for five cement plants of Pakistan on Homer Pro software and compares the optimal solutions based on the net present cost (NPC), levelized cost of electricity (LCOE) and greenhouse gas (GHG) emissions. Model-1 consists of solar panels, electrolyzer, hydrogen tank, hydrogen generator and converter. Model-2 has only a diesel generator and acts as a base case in this study. Model-3 has solar panels and a battery-converter system. In Model-4, diesel generators, solar panels and converters are considered. Based on NPC, the most optimal model is Model-4, having a 0.249 $/KWh LCOE in islanded systems. The NPC and operating costs are US$540 million and US$ 32.5 million per year, respectively, with a 29.80% reduction in CO2 emissions when compared to the base case. Based on GHG emissions, Model-1 and Model-3 are the best models with 0% GHG emissions. Sensitivity analyses is also performed using the parameters of load, inflation rate and discounted rate. The results prove that the proposed hybrid micropower systems (HMS) can sustainably provide electricity for 24 hours a day to the sites under consideration with minimum objectives.

A cross-flow ultrafiltration harvesting system of a pre-concentrated microalgae culture was tested in an innovative anaerobic-based WRRF. The microalgae culture was cultivated in a membrane photobioreactor fed with the effluent from an anaerobic membrane bioreactor treating sewage. These harvested microalgae biomass was then anaerobically co-digested with primary and secondary sludge from the water line. Depending on the needs of this anaerobic co-digestion, the filtration harvesting process was evaluated intermittently over a period of 212 days for different operating conditions, mainly the total amount of microalgae biomass harvested and the desired final total solids concentration (up to 15.9 g·L1 with an average of 9.7 g·L1). Concentration ratios of 15-27 were obtained with average transmembrane fluxes ranged from 5 to 28 L·m2·h1. Regarding membrane cleaning, both backflushing and chemical cleaning resulted in transmembrane flux recoveries that were, on average, 21% higher than those achieved with backflushing alone. The carbon footprint assessment shows promising results as the GHG emissions associated with the cross-flow ultrafiltration harvesting process could be less than the emissions savings associated with the energy recovered from the biogas production from the anaerobic valorisation of the harvested microalgae.

Additive Manufacturing (AM) has been proving suitable to support or even replace traditional manufacturing in several industries, offering many advantages such as delivery time and reduction in terms of material waste, energy consumption and greenhouse gas (GHG) emissions. This study aimed to carry out a comparative assessment of the life cycle, from gate to gate, in the production of a low alloy carbon steel flange part using ER-90 wire. The methods utilized were Wire and Arc Additive Manufacturing (WAAM) and conventional manufacturing (CM) by forging, and comparative factors were energy demands, GHG emissions and generated solid waste. The total energy consumption in WAAM was 10,239.40 MJ, total carbon footprint in CO2 equivalent (CO2e) was 714.1 kgCO2e kg-1, and generated solid waste was 68.6 kg, respectively, 90%, 95% and 76% lower than consumption calculated in conventional manufacturing.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

This paper provides an in-depth exploration of the role of Big Data and Artificial Intelligence (AI) in advancing dairy farming towards net zero emissions, a critical goal in the face of the global climate crisis. The study emphasizes how these technologies significantly enhance the management of greenhouse gas (GHG) emissions and optimize resource use, thereby contributing to environmental sustainability in agriculture. A key aspect of this transition is the alignment with international climate commitments, such as the Paris Agreement, which are instrumental in steering global efforts toward emission reduction and mitigating climate change. The integration of Big Data and AI in dairy farming emerges as a powerful tool to reduce the sector's environmental impact while sustaining economic growth. The paper delves into the specific applications of these technologies in emission management, including predictive analytics for feed optimization, manure management, and energy efficiency enhancements. It also addresses the broader implications of technological integration in dairy farming, considering aspects like benchmarking standards, data privacy, and the role of policy in fostering sustainable practices. The study underscores the challenges inherent in adopting these advanced technologies, including the need for improved farmer training, data quality, and compatibility with existing systems. It also advocates for enhanced policy frameworks that support sustainable practices, encourage technological adoption, and balance economic viability with environmental responsibility. This comprehensive analysis offers valuable insights into harnessing digital technologies for climate change mitigation and delineates a path for the dairy industry towards achieving net zero emissions, thereby contributing significantly to global environmental sustainability efforts.

This paper responds to the research question, “can urban farming help Nepali cities become more sustainable”? Especially after the Covid-19 pandemic, urban residents have begun to realize that food transported from long distances could not always be reliable. Urban farming can help produce fresh food locally and avoid long-distance transportation, and refrigeration. This practice also helps reduce greenhouse gases through plant carbon use efficiency (CUE). Urban farming not only helps city-dwellers towards achieving self-reliance in food production but also in vegetation carbon dynamics (VCD) while supporting the circular economy. Urban farming consists of edible landscapes, which can also be an aesthetic public space. As urban lands command higher prices than agricultural land, urban farming usually happens on residential yards, roofs, balconies, community gardens, and dedicated areas in public parks. Rainwater harvesting, and redirecting can help irrigate urban farms which can be part of rain gardens. The national census of 2021 (CBS 2022, p5) identifies that 66 percent of Nepal’s population live in urban areas. However, the World Bank (2018), shows that only 21 of Nepal’s population was projected to live in urban areas in 2021. It is not debatable that the urbanization process in Nepal is on the rise. Thus, urban agriculture can play an important role to supplement the residents’ food needs. Many cities in Nepal have already successfully adapted to urban farming where residents grow food on their building site, balconies, and rooftop often growing plants on pots, vases, and other types of containers. The UN-Habitat, with the support of European Union and local agencies, has published a rooftop farming training manual (2014) showing the feasibility of urban farming in Nepal.The paper discusses how Public Private Partnership (PPP) can promote urban agriculture and make the process more effective and attractive to urban farming households. It also analyzes how a PPP approach also facilitates the use of better technology, advisory support, and use of research extension activities. This paper draws on literature review, secondary data (e.g., from National Census Nepal 2021) and authors’ professional experiences related to best practices in the areas to analyze the benefits and challenges related to urban farming in Arizona, USA. The paper will provide recommendations for Nepali cities to maximize the benefit provided by urban farming. It is expected to be useful to Nepali policy makers, and government agencies, and nonprofit organizations which promote sustainability, and organic farming.

Cement industry is one of the highest energy consuming industries. The quantity of fuel and energy needed accounts for most of the cost of cement manufacturing. Thermal power plants generate electricity but are harmful and ineffective by nature. As a backup mechanism to account for main grid failures, batteries can be utilized. In this paper the first ever investigation on battery’s depth of discharge (DOD) for four different kinds of battery technologies is carried out in the framework of cement industry. The intended battery technologies are the lead-acid battery (LA), lithium-ion battery (Li-ion), vana-dium redox battery (VR), and nickel–iron battery (Ni-Fe). Four hybrid energy generation models (HEGMs) for five cement plants of Pakistan using the HOMER pro software are proposed. Cement plants includes Askari Cement Plant, Wah (ACPW); Bestway Cement Plant, Kalar Kahar (BCPKK); Bestway Cement Plant, Farooqia (BCPF); Bestway Cement Plant, Hattar (BCPH); and DG Cement Plant, Chakwal (DGCPC). HEGM-1 comprises of a diesel generator (DGen), a photovoltaic system (PV), a converter, and a battery system. HEGM-2 comprises of a PV system, a converter, and a battery system. HEGM-3 is the grid-connected version of HEGM-1 and HEGM-4 is the grid-connected version of HEGM-2. A base-model consisting of grid only is used as a reference. A multi-criteria decision analysis (MCDA) is performed by formulating a cumulative objective function (COF) which includes net present cost (NPC), levelized cost of energy (LCOE), and greenhouse gas (GHG) emissions. The principal objective is the maximization of COF while simultaneously minimizing the objectives (NPC, LCOE and GHG emissions), based on optimal battery technology and DOD. The results reveal that VR is the most suitable battery technology with 10% DOD. It is achieved for DGCPC with HEGM-3 with 61.49% of NPC, 78.62% of LCOE and 84.00% of GHG emissions reduction as com-pared to the base model.

The design and usage of the addressed combined fiber-optic sensors (ACFOS) and the multisensory control systems of the greenhouse gas concentration on their basis are investigated. The main development trend of the combined fiber-optic sensors (CFOS), consisting of the fiber Bragg grating (FBG) and the Fabry-Perot resonator (FPR), which are successively formed at the optical fiber end, is highlighted. The addressed fiber Bragg structures (AFBS) usage instead of the FBG in the CFOS leads not only to significant cheapening of the sensor system due to microwave photonics interrogating methods, but also to increasing its metrological characteristics. The structural scheme of the multisensory gas concentration monitoring system is suggested. The suggested scheme allows detecting four types of the greenhouse gases (СО2, NO2, CH4, OX) depending on the material and thickness of the polymer film, which is the FPR sensitive element. The usage of Karunen-Loeff transform (KLT), which allows separating each component contribution to the reflected spectrum according to its efficiency, is proposed. In the future, it allows determining the gas concentration at the AFBS address frequencies. The estimations have shown that the ACFOS design in the multisensory system allows measuring the environment temperature in the range of −60…+300 °C with an accuracy of 0.1–0.01 °C, and the gas concentration in the range of 10…90% with the accuracy of 0.1–0.5%.

Wind technology is considered to be among the most promising types of renewable energy sources, and due to high oil prices and growing concerns about climate change and energy security, it has been the subject of extensive considerations in recent years, including questions related to the relative sustainability of electricity production when the manufacturing, assembly, transportation and dismantling processes of these facilities are taken into account. The present article evaluates the environmental impacts, carbon emissions and water consumption, derived from the production of electric energy of the Villonaco wind farm, located in Loja-Ecuador, during its entire life cycle, using the Life Cycle Analysis method. Finally, it is concluded that wind energy has greater environmental advantages, since it has lower values of carbon and water footprints than other energy sources. Additionally, with the techniques Cumulative Energy Demand and Energy Return on Investment, sustainability in the production of electricity from wind power in Ecuador is demonstrated; and, that due to issues of vulnerability to climate change, the diversification of its energy mix is essential considering the inclusion of non-conventional renewable sources such as solar or wind, this being the only way to reduce both the carbon footprint and the water supply power.

Electric vehicles (EV) are getting more commonplace in the transportation sector in recent times. As the present trend suggests, this mode of transport is likely to replace the internal combustion engine (ICE) vehicles in near future. Each of the main EV components has a number of technologies that are currently in use or can become prominent in the future. EVs can cause significant impacts on the environment, power system, and other related sectors. The present power system can face huge instabilities with enough EV penetration; but with proper management and coordination, EVs can be turned into a major contributor to the successful implementation of smart grid. There are possibilities of immense environmental benefits as well, as the EVs can extensively reduce the greenhouse gas emission from the transportation sector. However, there are some major obstacles for EVs to overcome before replacing the ICE vehicles totally. This paper is focused on reviewing all the useful data available on EV configurations, energy sources, motors, charging techniques, optimization techniques, impacts, trends, and possible directions of future developments. Its objective is to provide an overall picture of the current EV technology and ways of future development to assist in future researches in this sector.

The building sector has a big potential to reduce the material resource demand needed for building construction and therefore, greenhouse gas (GHG) emissions. Digitalisation can help to make use of this potential and improve sustainability throughout the entire building’s life cycle. One way to address this potential is through the integration of Life-Cycle Assessment (LCA) into the building process by employing Building Information Modelling (BIM). BIM can reduce the effort needed to carry out an LCA and therefore facilitate the integration into the building process. A review of current industry practice and scientific literature shows two main approaches to address BIM-LCA integration. Either the LCA is performed in a simplified way at the beginning of the building process, or it is done at the very end when all the needed information is available, but it is too late for decision-making. One reason for this is the lack of methods, workflows and tools to implement BIM-LCA integration over the entire building process. Therefore, the main objective of this study is to develop an integrated BIM-LCA workflow implemented into a method for the whole building process using an existing structure for cost estimation. A tool is created and used in a case study in Switzerland to test the developed approach. The results of this study show that LCA can be performed continuously in each building phase over the entire building process using existing BIM modelling techniques. The main benefit of this approach is that the re-work caused by the need for re-entering data and the usage of many different software tools that characterise most of the current LCA practices is minimised. Furthermore, decision-making, both at the element and building levels, is supported.