The removable partial denture, despite new technologies and new materials, continues to play a significant role in clinical dental practice. The purpose of the following study was to evaluate the design of new retention devices in Kennedy's second grade classrooms. For the study of "lamellar" retentive devices, 4 prosthetists were chosen and selected, according to inclusion and exclusion criteria, 16 patients, 8 women and 8 men, whose upper arch had to be rehabilitated with a removable partial prosthesis. The results showed that the parameters taken into consideration such as satisfaction, stability, aesthetics and retention had an average score higher than 3.30 (range 1-4), with an average standard deviation of 0.6225 in the 4 indicative parameters that the data they are relatively homogeneous and coherent. In conclusion we can state that the skeletonized prosthesis with lamellar retentions, designed in Kennedy's second grade classes, has shown good acceptance in selected patients

The aim of this research is to investigate the influence of model height employed in the deep drawing of orthodontic aligner sheets on force transmission and aligner thickness. Forty sheets (Zendura FLX) were thermoformed over four models of varying heights (15, 20, 25, and 30 mm). Normal contact force generated on the facial surface of the upper right central incisor (Tooth 11) was measured using pressure-sensitive films. Aligner thickness around Tooth 11 was measured at five points. A digital caliper and a micro-computed tomography (µ-CT) were employed for thickness measurements. The normal contact force exhibited an uneven distribution across the facial surface of Tooth 11. Model 15 displayed the highest force (88.9±23.2 N), while Model 30 exhibited the lowest (45.7±15.8 N). The force distribution was more favorable for bodily movement with Model 15. Thickness measurements, conducted using a digital caliper and µ-CT, revealed substantial thinning of the aligner after thermoforming. This thinning was most pronounced at the incisal edge (50% of the original thickness) and least at the gingivo-facial part (85%). Additionally, there was a progressive reduction in aligner thickness with increasing model height, which was most significant on the facial tooth surfaces. We conclude that the thermoplastic aligner sheets undergo substantial thinning during the thermoforming process, which becomes more pronounced as the height of the model increases. As a result, there is a decrease in both overall and localized force transmission, which could lead to increased tipping by the aligner and a diminished ability to achieve bodily movement.

The aim of this study is to study the effect of aging in different media (deionized water and artificial saliva) on the force/torque generation by thermoplastic orthodontic aligners. Ten thermoformed aligners made of Essix ACE® thermoplastic sheets were aged in deionized water and in artificial saliva over two weeks at 37 C, five in each medium. The force/torque generated on upper second premolar (Tooth 25) of a resin model was measured at day 0 (before aging), 2, 4, 6, 10, and 14, using a biomechanical test set-up. The results showed that the thermocycling of aligners has no significant impact on their force/torque decay. No significant differences were also found in force/torque between the aligners stored in deionized water nor artificial saliva. The vertical extrusion-intrusion forces were measured in the range of 1.4 to 4.6 N, the horizontal oro-vestibular forces were 1.3 to 2.5 N, while the torques on mesio-distal rotation were 5.4 to 41.7 Nmm. It could be concluded that the influence of saliva on the mechanical properties can be classified as insignificant, and no significant difference between artificial aging in deionized water or artificial saliva was observed.

The integration of three-dimensional (3D) printed resin denture teeth represents a significant ad-vancement in digital dentistry. This study aimed to assess their ability to withstand chipping and indirect tensile fractures, comparing them with conventionally manufactured resin denture teeth. Four groups, each comprising 30 specimens, were examined: Group 1 featured 3D printed denture teeth (NextDent, 3D Systems, Soesterberg, The Netherlands), while the others included commer-cially obtained Ivostar Shade, SpofaDent Plus, and Major Super Lux teeth. Stereolithography 3D printing was utilized to produce methacrylate-based photopolymerized resin teeth models for Group 1, while the remaining groups were commercially sourced. Chipping and indirect tensile fracture tests were performed at a speed of 1 mm/min until fracture occurred. Statistical analysis was conducted using one-way analysis of variance (ANOVA) with Tukey's honestly significant difference multiple comparisons test (p < 0.05). Results indicated that 3D-printed teeth exhibited higher indirect tensile fracture resistance than Major Super Lux and Ivostar Shade but lower than SpofaDent Plus. Additionally, in the chipping test, buccal chipping occurred in 3D-printed resin teeth without distortion. In the indirect tensile test, the fracture line emerged near the loading point, extending cervically from the inner incline of both cusps. Overall, denture teeth produced via 3D printing with printable resin materials demonstrated sufficient fracture resistance, making them suitable for prosthetic applications.

The aim of the study is to investigate the effects of artificial aging by thermocycling and mechanical loading on force/torque delivery by thermoplastic orthodontic aligners. Ten thermoformed aligners made of Zendura™ thermoplastic polyurethane sheets were aged over two weeks in deionized water by thermocycling alone (n=5) and by both thermocycling and mechanical loading (n=5). The force/torque generated on upper second premolar (Tooth 25) of a plastic model was measured before aging (as control), and after 2, 4, 6, 10, and 14 days of aging, using a biomechanical set-up. Before aging, the extrusion-intrusion forces were in the range of 2.4 to 3.0 N, the oro-vestibular forces were 1.8 to 2.0 N, and the torques on mesio-distal rotation were 13.6 to 40.0 Nmm. Pure thermocycling had no significant effect on the force decay of the aligners. However, there was a significant decrease in force/torque after 2 days of aging for both thermocycling and mechanical loading aging group, which is no longer significant over 14 days of aging. In conclusion, artificial aging of aligners in deionized water with thermocycling and mechanical loading results in a significant decrease in force/torque generation. However, the mechanical loading of aligners has a greater impact than thermocycling alone.

Laser powder bed fusion (L-PBF) is a type of additive manufacturing technology that processes metal powders into a component. Support structures are an essential part of the L- PBF process as they transfer the laser-induced heat during and shortly after the process to the substrate, sustaining positional accuracy of downward facing surfaces of the component. Since the use of support structures is inevitable, optimized designs for them are crucial in realizing more sustainable production process. In a serial production setup, reducing the lead time and cost of a non-value-added process step like support structure removal is of significance when improving the overall business case and competitiveness.The goal of this study was to verify the applicability of lattice-based support structures for L-PBF. To achieve this, different lattice types as support structures were designed. They were tested, compared and verified for a Siemens gas turbine component. The results showed that the generated lattice-based support structures could be suitable for L-PBF. The supports had to be designed appropriately such that they could preserve the geometry of the part. Furthermore, they had to have a short fabrication time and to be removable easily, preferably without machining or sawing.